Datalogic Scanning I GD4100 Bedienungsanleitung

Gr yphon ™ I GD4100 Linear I m ager Barc ode Reader P roduct Referenc e Guide [...]

Datalogic Scanning, Inc. 959 T err y Str eet  Euge ne, Oregon 974 02  T eleph one: (541) 683-5700  F ax: (541) 345-7140 An Unpublished W ork - All rights reserved. No par t of the contents of this documentation or the procedur es described therein may be repr oduced or transmitted in an y form or by an y means without prior written permiss[...]

Pr oduct Reference Guide 1 T able of C ont ents Introduction ............................................................................................. ...................... ................................................................... 7 About this Guide ................ ........................................ ...........................[...]

Contents 2 Gryphon™ I GD4100 RS-232/USB-Com Interfaces ................................................ ...................................................... .................................................... 59 Introduction ............................................. ................................................... .................. ...[...]

Contents Pr oduct Reference Guide 3 Symbologies ......................................................................... ........................................... ................................ ............................ 127 Introduction ............................................. ................................................... .......[...]

Contents 4 Gryphon™ I GD4100 Code 39 Check Character Transmission ................................................................ .......................... .............. ......................................... ................................... 173 Code 39 Start/Stop Character Transmission ................................... ...............[...]

Contents Pr oduct Reference Guide 5 Codabar Start/Stop Character Match ..................................................................... ....................... ................. ......................................... ............................... .... 233 Codabar Quiet Zones ................................................................[...]

Contents 6 Gryphon™ I GD4100 Control Character Emulation ................................................................ ................................... ...... .............................. ......................................... ................................... 305 Single Press and Release Keys ........................................[...]

Pr oduct Reference Guide 7 Chapter 1 Intr oduc tion About this Guide This Product Reference Guide (PRG) is provided for users seeking advanced technical information, including connection, programming, maintenance and specifications. The Quick Reference Guide (QRG) and other publications associated with this product are downloadable free of charge f[...]

Introduction 8 Gryphon™ I GD4100 Chapter 11, Data Ed iting offers advanced configuration options for cus tomization of scanned data output. Chapter 12, Symbologies defines options for all symbologies and provides the programming barcodes necessary for configuring these features. Appendix A, T echnical Specifications lists physical and performance[...]

Technical Support Pr oduct Reference Guide 9 T echnical Suppor t Datalogic W e bsite Support The Datalogic website ( www .scanning.datalogic.com ) is the complete source for technical support and information for Datalogic products. The site offers product support, product registration, warranty information, product manuals, product tech notes, soft[...]

Introduction 10 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 11 Chapter 2 Getting Star ted About the Reader Advancements in the LED technology used in this reader significantly improve the illumination of the target field of view, resulting in higher scan efficiency. Whether used in Single Trigger or Continuous Mode, the ergonomic design of the reader will help to promote comfortable[...]

Getting Started 12 Gryphon™ I GD4100 Install the Inter face C able Connect the reader cable by inserting the cable into the handle as shown in Fi g u re 1 . To remove it, insert a paper clip into the release aperture , then unplug the ca ble. Figure 1. Connect/disconnect the cable RS-232 Serial Connection Turn off power to the terminal/PC and con[...]

Setting Up the Reader Pr oduct Reference Guide 13 Ke yboard W edge C onnec tion The Keyboard Wedge cable has a ‘Y’ connection from the reader . Connect the female to the male end from the keyboard and the remaining end at the keyboard port at the terminal/PC. Reference Figu r e 3 . Figure 3. Keyboard Wedge Interface connection USB C onnection C[...]

Getting Started 14 Gryphon™ I GD4100 Figure 5. Other Interface Connections U S B I B M K e y b o a r d W e d g e or ... or ... NO TE Pr ogr amming The reader is factory-configured with a set of default features standard. After scanning the interface barcode from the Inter f aces section, you can select other options and customize your reader thro[...]

Resetting the Standa rd Product Defaults Pr oduct Reference Guide 15 Selec t the Interface T ype Upon completing the physical connection between the reader and its host, proceed directly to "Interfaces"on page 17 for information and programming for the interface type the reader is connected to (for example: RS-232, Keyboard Wedge, USB, et[...]

Getting Started 16 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 17 Chapter 3 Int er faces Inter face Selec tion Each reader model will support one of the following sets of host interfaces: General P urpose Models RS-232 RS-232 OPOS USB Keyboard Wedge Retail P oint of Sale Models RS-232 RS-232 OPOS USB IBM 46XX C onfiguring the Inter face Scan the programming barcode from this sec tion w[...]

Interfaces 18 Gryphon™ I GD4100 Table 1. Available Interfaces RS-232 FEA TURES RS-232 standard int er face Selec t RS2 32-STD Set RS-232 Interface Fe a t u r e s starting on page 51 Select RS232-WN RS-232 Wincor-Nix dorf RS-232 for use with OPOS/UPOS/Ja vaPOS Select RS-232 OPOS Sele ct U SB- C OM- STD a a. Download the correct USB Com driver from[...]

Configuring the Interface Pr oduct Reference Guide 19 KEYBO ARD FEA TURES A T , PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80 , 90 & 95 w/Standard Key Encoding Sel ect K BD -A T Set KEYBOA RD WEDGE Interface Fea t u re s starting on page 79 Select KBD-A T-NK Keyboar d W edge fo r IBM A T PS2 with standard key encoding but without external keyboard A[...]

Interfaces 20 Gryphon™ I GD4100 KEYBO ARD — cont. FEA TURES Keyboard W edge for IBM T erminals 31xx, 32xx, 34xx, 37xx make only keyboard Select KBD-IBM -M Set KE YBOARD WEDGE Interface F eatur es star ting on page 79 Select KBD-IBM-MB Keyboard W edge for IBM T e rminals 31xx, 32xx, 34xx, 37xx make break ke yboard Keyboard W edge for DIGIT AL T [...]

Global Interface Features Pr oduct Reference Guide 21 Global Inter fac e F eatures The following interface features are co nfigurable by all interface types. To set features specific to your interface, turn to that section of this manual: • RS-232 ONL Y Interface on page 51 • Keyboard Int er face on page 79 • USB-OEM Interface on page 93 • [...]

Interfaces 22 Gryphon™ I GD4100 USB Suspend Mode This setting enables/disables the ab ility of USB interfaces to enter suspend mode. ENTER/EXIT PROGRAMMING MODE USB Suspend Mode = Disable USB Suspend Mode = Enable DEF A UL T[...]

Pr oduct Reference Guide 23 Chapter 4 General F eatures Double Read Timeout To prevent a double read of the same label, the Double Read Timeout sets the minimum time allowed between reads of labels of the same symbology and data. If the unit reads a label and sees the same label again within the Double Read Timeout, the second read of the label wil[...]

General Features 24 Gryphon™ I GD4100 Double Read T imeout — c ontinued ENTER/EXIT PROGRAMMING MODE Double Read Timeout = 0.5 Second Double Read Timeout = 0. 6 Second Double Read Timeout = 0.7 Second Double Read Timeout = 0. 8 Second Double Read Timeout = 0.9 Second Double Read Ti meout = 1 Second[...]

Label Gone Timeout Pr oduct Reference Guide 25 Label Gone Timeout This feature sets the time after the last label segment is seen before the reader prepares for a new label. The timeout can be set within a range of 10 milliseconds to 2,550 milliseconds (2.55 seconds) in 10ms increments. Label Gone Timeout does not apply to scan modes that require a[...]

General Features 26 Gryphon™ I GD4100 Label Gone T imeout — c ont. ENTER/EXIT PROGRAMMING MODE Select La bel Gone Timeout Se tting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 016 = Tim eout of 160 ms[...]

Sleep Mode Timeout Pr oduct Reference Guide 27 Sleep Mode Timeout Specifies the timeout value for the reader to enter low power Sleep Mode. When Sleep Mode is enabled the reader cannot receive commands from the Host or base station. In order for the reader to enter Sleep Mode, the following con ditions must be met: RS-232 interface and trigger sing[...]

General Features 28 Gryphon™ I GD4100 Sleep Mode T imeout — co ntinued ENTER/EXIT PROGRAMMING MODE Sleep Mode Timeout = 5 Seconds Sleep Mode Timeout = 6 Seconds Sleep Mode Timeout = 7 Seconds Sleep Mode Timeout = 8 Seconds Sleep Mode Timeout = 9 Seconds Sleep Mode Timeout = 10 Seconds max. $ $[...]

LED and Beeper Indicators Pr oduct Reference Guide 29 LED and Beeper Indicators Pow e r O n A l e r t Disables or enables the indication (from the Beeper) that the reader is receiving power. ENTER/EXIT PROGRAMMING MODE Po wer On Alert = Disable (No Audible Indication) Po wer On Alert = Four Beeps DEF A UL T[...]

General Features 30 Gryphon™ I GD4100 Good Read: When to Indicate This feature specifies when t he reader will provide indication (beep and/or flash its green LED) upon successfully reading a barcode. Choices are: • Good Read = I ndicate after decode • Good Read = I ndicate after transmit • Good Read = I ndicate after CTS goes inactiv e, th[...]

LED and Beeper Indicators Pr oduct Reference Guide 31 Good Read B eep T ype Specifies whether the good read beep has a mono or bitonal beep sound. ENTER/EXIT PROGRAMMING MODE Good Read Beep T ype = Mono Good Read Beep T ype = Bitonal DEF A UL T[...]

General Features 32 Gryphon™ I GD4100 Good Read Beep Fr equency Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/tone.) Good Read B eep Length Specifies the duration of a good read beep. ENTER/EXIT PROGRAMMING MODE Good Read B eep Fr equency = Low Goo[...]

LED and Beeper Indicators Pr oduct Reference Guide 33 Good Read Beep Length — c ontinued ENTER/EXIT PROGRAMMING MODE Good Read Beep Length = 80 msec Good Re ad Beep Length = 100 msec Good Read Beep Length = 120 msec Good Re ad Beep Length = 140 msec Good Read Beep Length = 160 msec Good Re ad Beep Length = 180 msec Good Read Beep Length = 200 mse[...]

General Features 34 Gryphon™ I GD4100 Good Read B eep V olume Selects the beeper vol ume (loudness) upon a good read beep . There are three selectable volume levels. ENTER/EXIT PROGRAMMING MODE Good Read Beep V olume = Beeper O ff Good Read Beep V olume = Lo w Good Read B eep V olume = Medium Good Read Beep V olume = High DEF A UL T[...]

LED and Beeper Indicators Pr oduct Reference Guide 35 Good Read LED Duration This feature specifies the amount of time that the Good Read LED remains on following a good read. The good read LED on time can be set within a range of 10 milliseconds to 2,550 milliseconds (0.001 to 2. 55 seconds) in 10ms increments. Follow these instructions to set thi[...]

General Features 36 Gryphon™ I GD4100 Good Read LED Dura tion — con t. ENTER/EXIT PROGRAMMING MODE Select G ood Read LED Duration Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 020 = Good Read LED stays on for 2 seconds. NO TE Indicat ors[...]

Scanning Features Pr oduct Reference Guide 37 Scanning F eatures Scan Mode Selects the scan operating mode for the reader. Selections are: T rigger Single. When the trigger is pulled, scanning is activated until one of the following occurs: - Scanning Active Time has elapsed - a label has been re ad - the trigger is released This mode is associated[...]

General Features 38 Gryphon™ I GD4100 Scan Mode — continued ENTER/EXIT PROGRAMMING MODE Scan Mode = T rigger Single Scan Mode = T rigger Hold Multiple Scan Mode = T rigger Pulse Multiple Scan Mode = Flashing Scan Mode = Always On Scan Mode = Stand Mode Scan Mode = T rigger Object Se nse DEF A UL T[...]

Scanning Features Pr oduct Reference Guide 39 Stand Mode T riggered Timeout This feature specifies the time to remain in Tr i g g e r S i n g l e mode after the trigger is pulled while in Stand Mode . NO TE ENTER/EXIT PROGRAMMING MODE Stand Mode T rigger ed Timeout = 0.5 Seconds DEF A UL T Stand Mode T rigg ered Timeout = 1.5 Seconds Stand Mode T r[...]

General Features 40 Gryphon™ I GD4100 Stand Mode T riggered T imeout — continued ENTER/EXIT PROGRAMMING MODE Stand Mode T rigger ed Timeout = 6 Seconds Stand Mode T riggered Timeout = 8 Seconds Stand Mode Triggered Timeout = Switch back to Trigger Single on trigger pull[...]

Scanning Features Pr oduct Reference Guide 41 Stand D ete c tion Specifies the behavior of the scanner when placed in a stand that contains autorecognition hardware. ENTER/EXIT PROGRAMMING MODE Stand Detection = Ignore Autorecognition DEF A UL T $ Stand Detect ion = Switch to object sense Stand Detect ion = Switch to always on Stand Detection = Swi[...]

General Features 42 Gryphon™ I GD4100 Scanning Activ e Time This setting specifies the amount of time that the reader stays in scan ON state once the state is entered. The range for this setting is from 1 to 255 seconds in 1-second increments. Follow these instructions to set this feature: 1. Determine the desired setting. 2. P ad the result with[...]

Scanning Features Pr oduct Reference Guide 43 Scanning Active T ime — con t. ENTER/EXIT PROGRAMMING MODE Select Scanning Ac tive Time Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 005 = Scann ing is active for 5 Seconds[...]

General Features 44 Gryphon™ I GD4100 F lash On Time This feature specifies the ON time for the indicator LED while in Flash Mode. The selectable range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. Follow these instructions to set this feature. 1. Determine the desired setting in milliseconds. 2. Divide the des[...]

Flash On Time Pr oduct Reference Guide 45 Fla s h O n Tim e — cont . ENTER/EXIT PROGRAMMING MODE Select Flash ON Time Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 10 = Flash is ON for 1 Second[...]

General Features 46 Gryphon™ I GD4100 F lash Off Time This feature specifies the OFF time for the indicator LED while in Flash Mode. The selectable range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. Follow these instructions to set this feature. 1. Determine the desired setting in milliseconds. 2. Divide the d[...]

Stand Mode Sensitivity Pr oduct Reference Guide 47 Flash Off T ime — cont . Stand Mode Sensitivity Sets the sensitivity level for stand mode wakeup. Choices are low, medium and high. ENTER/EXIT PROGRAMMING MODE Select Flash OFF Time Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t ag[...]

General Features 48 Gryphon™ I GD4100 Stand Det ec tion Specifies the behavior of the scanner when placed in a stand that contains autorecognition hardware. ENTER/EXIT PROGRAMMING MODE Ignore Autor ecognition Switch to Object Sense Switch to Always On Swit ch to F lashing DEF A UL T[...]

Green Spot Duration Pr oduct Reference Guide 49 Green Spot Dur ation Specifies the duration of the good read pointer beam after a good read. ENTER/EXIT PROGRAMMING MODE Green Spot Dura tion = Disable (Green Spot is Off ) Green Spot Duration = Short (300 msec) Green Spot Duration = Medium (500 msec) Green Spot Dura tion = Long (800 msec) DEF A UL T[...]

General Features 50 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 51 Chapter 5 RS-232 ONL Y Inter fac e Introduc tion Use the programming barcodes in this chapter if modifications to the standard RS-232 interface settings are necessary to meet your system’s re quirements. Additional settings which apply to both the RS-232 and USB interfaces are available in Chapt er 6, RS-232/USB-C om I[...]

RS-232 ONLY Interface 52 Gryphon™ I GD4100 Baud Rate Baud rate is the number of bits of data transmitt ed per second. Set the reader's baud rate to match the baud rate setting of the host device. With an improper baud rate setting, data may not reach the host correctly. ENTER/EXIT PROGRAMMING MODE Baud Rate = 1200 Baud Rate = 2400 Baud Rate [...]

Baud Rate Pr oduct Reference Guide 53 Baud Rate — con tinued ENTER/EXIT PROGRAMMING MODE Baud Rate = 9600 Baud Rate = 19,200 Baud Rate = 38,400 Baud Rate = 57,600 Baud Rate = 115,200 DEF A UL T[...]

RS-232 ONLY Interface 54 Gryphon™ I GD4100 Data Bits This parameter allows the reader to interface with devices requiring a 7-bit or 8-bit ASCII protocol for sending and receiving data. ENTER/EXIT PROGRAMMING MODE 7 Data Bits 8 Data Bits DEF A UL T[...]

Stop Bits Pr oduct Reference Guide 55 Stop Bits The stop bit(s) at the end of each trans mitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial data stream. The number of stop bits selected (one or two) depends on the number the receiving terminal is programmed to accom[...]

RS-232 ONLY Interface 56 Gryphon™ I GD4100 P arity This feature specifies parity required for sending and receiving data. A parity check bit is the most significant bit of each ASCII coded character. Select the parity type according to host device requirements. • Select N one when no parity bit is required. • Select Odd parity and the parity [...]

Handshaking Control Pr oduct Reference Guide 57 Handshaking Con trol The data interface consists of an RS-232 port designed to operate either with or without the hardware handshaking lines, Request to Send (RTS), and Clear to Send (CTS). Handshaking Control includes the following options: • R TS — R TS is asserted during transmissions. CTS is i[...]

RS-232 ONLY Interface 58 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 59 Chapter 6 RS -232/USB - C om In ter faces Introduc tion The programming barcodes in this chapter allow modifications to the standard RS-232 and USB-Com interfaces. Standard F ac tor y S ettings Reference Appendix C, Standar d Defaults for a listing of standard factory settings.[...]

RS-232/USB-Com Interfaces 60 Gryphon™ I GD4100 Interchar ac ter Dela y This parameter specifies the intercharacter de lay be tween the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments. A setting of zero specifies no delay. To set the delay: 1. Determine the [...]

Intercharacter Delay Pr oduct Reference Guide 61 Interchar acter Delay — cont . ENTER/EXIT PROGRAMMING MODE Inter character Dela y = No Delay Sele ct In t er ch ar act er De la y Se tti ng Make a mistake? Scan the CANCEL barcode to abort and not save the entr y string. Y ou can th en star t again at the begin ning. CANCEL DEF A UL T 00 = No Inter[...]

RS-232/USB-Com Interfaces 62 Gryphon™ I GD4100 Beep On ASCII BEL When this parameter is enabled, the reader issues a beep when a <BEL> character is detected on the RS-232 serial line. <BEL> is issued to gain a user's attention to an illegal entry or other important event. ENTER/EXIT PROGRAMMING MODE Beep On ASCII BEL = Disable Be[...]

ACK NAK Options Pr oduct Reference Guide 63 A CK NAK Options This enables/disables the ability of the reader to support the RS-232 ACK/NAK protocol. When configured, the reader and/or host sends an “ACK” when it receives data properly, and sends “NAK” when the data is in error. Options are: • Disable • Enable for label transmission — [...]

RS-232/USB-Com Interfaces 64 Gryphon™ I GD4100 A CK Charac ter This setting specifies an ASCII character or hex value to be used as the ACK character. ASCII characters or any hex value from 0 to 0xFF can be selected. NO TE To set this feature: 1. Determine the desired character or value. 2. U se the ASCII Char t on the inside back cover of this m[...]

ACK NAK Options Pr oduct Reference Guide 65 A CK Character — cont. ENTER/EXIT PROGRAMMING MODE Select ACK Character Setting DEF A UL T 0x06 ‘ACK’ Character[...]

RS-232/USB-Com Interfaces 66 Gryphon™ I GD4100 NAK Character This setting specifies an ASCII character or hex value to be used as the NAK character. ASCII characters or any hex value from 0 to 0xFF can be selected. NO TE To set this feature: 1. Determine the desired character or value. 2. U se the ASCII Char t on the inside back cover of this man[...]

ACK NAK Options Pr oduct Reference Guide 67 NAK Character — cont. ENTER/EXIT PROGRAMMING MODE Select NAK Charac ter Setting DEF A UL T 0x15 ‘NAK’ Character[...]

RS-232/USB-Com Interfaces 68 Gryphon™ I GD4100 A CK NAK Timeout V alue This option specifies the amount of time the reader waits for an ACK character from the host following label transmission. The selectable timeout range is 200 milliseconds to 15,000ms (15 seconds) in 200ms increments. A selection of 0 disables the timeout. To set this value: 1[...]

ACK NAK Options Pr oduct Reference Guide 69 A CK NAK T imeout V alue — con t. ENTER/EXIT PROGRAMMING MODE Select ACK NAK Timeout V alue Set ting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 01 ACK NAK Timeout value is 200ms[...]

RS-232/USB-Com Interfaces 70 Gryphon™ I GD4100 A C K NAK Retr y C ount This feature specifies the number of times the reader retries a label transmission due to a retry condition. The selectable range is from 1 to 254 retries. A selection of 0 disables the count, and a selection of 255 specifies unlimited retries. To set this feature: 1. Determin[...]

ACK NAK Options Pr oduct Reference Guide 71 A CK NAK Retry Count — con t. ENTER/EXIT PROGRAMMING MODE Select ACK NAK Retr y Count Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 003 = 3 Ret ries[...]

RS-232/USB-Com Interfaces 72 Gryphon™ I GD4100 A CK NAK Error Handling This feature specifies the method the reader uses to handle receive errors detected while waiting for an ACK character from the host. Options are: • Ignore err ors detected • P rocess err or as valid ACK character • P rocess err or as valid NAK character ENTER/EXIT PROGR[...]

Indicate Transmission Failure Pr oduct Reference Guide 73 Indicat e T ransmission F ailure This option enables/disables the reader’s ability to sound an error beep to indicate a transmission failure while in ACK/NAK mode ENTER/EXIT PROGRAMMING MODE Indicat e T ransmission F ailure = Disable Indica tion Indicate T ransmission F ailure = Enable Ind[...]

RS-232/USB-Com Interfaces 74 Gryphon™ I GD4100 Disable Character Specifies the value of the RS-232 host command used to disable the reader. ASCII characters or any hex value from 0 to 0xFF can be selected. NO TE To set the value: 1. Determine the desired character or value. A setting of 0xFF indicates the Disable Charac- ter is not used (not avai[...]

Disable Character Pr oduct Reference Guide 75 Disable Character — cont . ENTER/EXIT PROGRAMMING MODE Select Disa ble Character Setting DEF A UL T 0x44 = Disable Character is ‘D’[...]

RS-232/USB-Com Interfaces 76 Gryphon™ I GD4100 Enable Character Specifies the value of the RS-232 host command used to enable the reader. ASCII characters or any hex value from 0 to 0xFF can be selected. NO TE To set this feature: Determine the desired character or value. A setting of 0xFF indicates the Enable Character is not used (not available[...]

Enable Character Pr oduct Reference Guide 77 Enable Character — cont . ENTER/EXIT PROGRAMMING MODE Select Enab le Character Setting DEF A UL T 0x45 = Enable Character is ‘E’[...]

RS-232/USB-Com Interfaces 78 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 79 Chapter 7 K eyboar d Inter face Introduc tion Use the programming barcodes in this chapter to select options for USB Keyboard and Wedge Interfaces. Standard F ac tor y S ettings Reference Appendix C, Standar d Defaults for a listing of standard factory settings. Scancode T ables Information about control character emulat[...]

Keyboard Interface 80 Gryphon™ I GD4100 Country Mode This feature specifies the country/language supported by the keyboard. Only the following interfaces support ALL Country Modes. • USB Keyboard (without alternate key encoding) • A T , PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/S td Key Encoding • Keyboar d W edge for IBM A T [...]

Country Mode Pr oduct Reference Guide 81 C ountry Mode — continued ENTER/EXIT PROGRAMMING MODE Country Mode = Denmark Supports only the inter faces listed in the C ountry Mode featur e description. Coun try Mode = Franc e Co untry Mode = Germany Supports only the inter faces listed in the C ountry Mode fea- ture description. Coun try Mode = Hunga[...]

Keyboard Interface 82 Gryphon™ I GD4100 C ountry Mode — continued ENTER/EXIT PROGRAMMING MODE Country Mode = Poland Supports only the inter faces listed in the C ountry Mode featur e description. Supports only the inter faces list ed in the Country Mode fea- ture description. Country Mode = Portugal Country Mode = Romania Supports only the inte[...]

Caps Lock State Pr oduct Reference Guide 83 Cap s Loc k St at e This option specifies the format in which the reader sends character data. This applies to keyboard wedge interfaces. This does not apply when an alternate key encoding keyboard is selected. ENTER/EXIT PROGRAMMING MODE Caps L ock State = Caps L ock OFF Caps Loc k S tate = Ca ps Lock ON[...]

Keyboard Interface 84 Gryphon™ I GD4100 Send C ontrol Char acters This feature Specifies how the reader transmits ASCII control char acters to the hos t. Reference Appendix F , Scancode T ables for more information about control characters. Options are as follows: C ontrol Character 00 . Characters from 00 to 0x1F are sent as control character Ct[...]

Wedge Quiet Interval Pr oduct Reference Guide 85 W edge Quiet Interval This option specifies the amount of time to look for keyboard activity before the reader breaks the keyboard connection in order to transmit data to host. The selectable range for this feature is from 0 to 990ms in 10ms increments. NO TE Follow these instructions to set this fea[...]

Keyboard Interface 86 Gryphon™ I GD4100 W edge Quiet Inter val — con t. 6 Scan ENTER/EXIT PROGRAMMING MODE ENTER/EXIT PROGRAMMING MODE Selec t Wedge Quiet Interval Set ting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL STEP A CTION EXAMPLES 1 Desired Setti[...]

Intercharacter Delay Pr oduct Reference Guide 87 Interchar ac ter Dela y This parameter specifies the intercharacter de lay be tween the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments. A setting of zero specifies no delay. NO TE To set the delay: 1. Determin[...]

Keyboard Interface 88 Gryphon™ I GD4100 Interchar acter Delay — con t. ENTER/EXIT PROGRAMMING MODE Inter character Dela y = No Delay Selec t Intercharacter D elay Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entr y string. Y ou can th en star t again at the begin ning. CANCEL DEF A UL T 00 = No Intercharacter Delay[...]

Intercode Delay Pr oduct Reference Guide 89 Interc ode Delay Specifies the delay between labels transmitted to t he host for this interface. The selectable range for this feature is from 0 to 99 seconds. Follow these instructions to set this feature: 1. Determine the desired setting. 2. P ad the number with leading zeroes to yield two digits. Fo r [...]

Keyboard Interface 90 Gryphon™ I GD4100 Interc ode Delay — c o nt. ENTER/EXIT PROGRAMMING MODE Set Intercode Delay Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 00 = No Wed ge Intercode Delay[...]

USB Keyboard Speed Pr oduct Reference Guide 91 USB K e yboard Speed This option specifies the USB poll rate for a USB keyboard. NO TE ENTER/EXIT PROGRAMMING MODE USB Keyboard Speed = 1ms USB Keyboard Speed = 2ms USB Keyboard Speed = 3ms USB Keyboard Speed = 4ms USB Keyboard Speed = 5ms This feature applies ONL Y to the USB K eyboard interface. DEF [...]

Keyboard Interface 92 Gryphon™ I GD4100 USB K eyboard Speed — c ontinued ENTER/EXIT PROGRAMMING MODE USB Keyboard Speed = 6ms USB Keyboard Speed = 7ms USB Keyboard Speed = 8ms USB Keyboard Speed = 9ms USB Keyboard Speed = 10ms[...]

Pr oduct Reference Guide 93 Chapter 8 USB - OEM Inter face Introduc tion Feature settings for USB interfaces differ depending upon which host type the reader will be connected with. Use the feature settings in this chapter and Chapter 9, IBM 46X X Inter face to specifically configure for the US B-OEM interface. Other USB interfaces are included in [...]

USB-OEM Interface 94 Gryphon™ I GD4100 USB-OEM Devic e U sage The USB-OEM protocol allows for the reader to be identified as one of two different types of barcode scanners. Depending on what other scanners you may already have connected to a USB-OEM POS, you may need to change this setting to enable all devices to communicate. Options are: • T [...]

Pr oduct Reference Guide 95 Chapter 9 IBM 46X X Inter face Introduc tion Use the barcodes in this section to configure programmable features for available IBM 46XX interfaces. IBM Standard F a c tor y S ettings Reference Appendix C, Standar d Defaults for a listing of standard factory settings.[...]

IBM 46XX Interface 96 Gryphon™ I GD4100 46xx Number of Host Resets Specifies how many consecutive resets are processed before the reader starts a five-second period to allow the user to enter Programming Mode and configure the reader. The configurable range for this feature is 1 to 15 resets. ENTER/EXIT PROGRAMMING MODE 46xx Number of Hos t Reset[...]

ENTER/EXIT PROGRAMMING MODE 46xx Number of Hos t Resets = 7 46xx Number of Hos t Resets = 8 46xx Number of Hos t Resets = 9 46xx Number of Host Resets = 10 46xx Number of Host Resets = 11 46xx Number of Host Resets = 12 46xx Number of Host Resets Pr oduct Reference Guide 97 46xx Number of Host Resets — c ont.[...]

ENTER/EXIT PROGRAMMING MODE 46xx Number of Host Resets = 13 46xx Number of Host Resets = 14 46xx Number of Host Resets = 15 IBM 46XX Interface 98 Gryphon™ I GD4100 46xx Number of Host Resets — c ont.[...]

Transmit Labels in Code 39 Format Pr oduct Reference Guide 99 T ransmit Labels in C ode 39 F ormat This feature enable/disables translation to Code 39 before transmitting label data to an IBM- 46XX or a USB-OEM host. Only the symbology identifier is modified for the translation. The data is not converted to Code 39 or verified to be valid for Code [...]

IBM 46XX Interface 100 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 101 Chapter 10 W and Emulation Inter face Introduc tion This chapter provides feature/settings configuration for the Wand Emulation interface. W and Emulation Standard F ac tor y Settings Reference Appendix C, Standar d Defaults for a listing of standard factory settings. W and Idle State This feature specifies the level of[...]

Wand Emulation Interface 102 Gryphon™ I GD4100 W and P olarity This option specifies the polarity of the Wand output signal. Choices are: • Quiet zones and spaces ar e high, bars are lo w • Quiet zones and spaces are lo w , bars are high NO TE ENTER/EXIT PROGRAMMING MODE W and P olarity = Quiet Zones & Spaces High, Bars Low W and P olarit[...]

Wand Signal Speed Pr oduct Reference Guide 103 W and Signal Speed This feature specifies the speed of the Wand output signal per nominal bar or space. Choices are: • 330 microseconds • 660 microseconds NO TE ENTER/EXIT PROGRAMMING MODE W a nd Signal Speed = 330ms W and Signal Speed = 660ms TTL logic levels:  0 V <= Low <= 0.7V  2.4V[...]

Wand Emulation Interface 104 Gryphon™ I GD4100 Label S ymbology C on version When this feature is enabled for the Wand Emulation interface, all barcode labels are converted to a single symbology.  Options are: • N o conversion • Convert to Code 39 symbology • Convert to Code 128 symbology NO TE ENTER/EXIT PROGRAMMING MODE Label Symbology[...]

Transmit Noise Pr oduct Reference Guide 105 T ransmit Noise This option specifies the leading/trailing noise for the Wand interface.  Choices are: • Disable (no leading/trailing noise) • Enable leading noise • Enable trailing noise • Enable leading and trailing noise NO TE ENTER/EXIT PROGRAMMING MODE T ransmit Noise = D isable T ransmit [...]

Wand Emulation Interface 106 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 107 Chapter 11 Data Editing Data E diting Ov er view When a barcode is scanned, additional information can be sent to the host computer along with the barcode data. This combination of barcode data and supplementary user-defined data is called a “message string.” The features in this chapter can be used to build specifi[...]

Data Editing 108 Gryphon™ I GD4100 Please K eep In Mind ... • M odifying a message string is not a mandatory requirement. Data editing is sophisticated feature allowing highly customizable output for advanced users. F actor y default settings for data editing is typically set to NONE. • A prefix or suffix may be applied (refer ence the Sy mbo[...]

Global Prefix/Suffix Pr oduct Reference Guide 109 5. If less than the expected string of 20 characters ar e selected, scan the ENTER/EXIT bar- code to terminate the string. 6. Scan the ENTER/EXIT barcode once again to exit P rogramming M ode. 7. The resulting message string would appear as follo ws: Scanned barcode data:12345 Resulting message stri[...]

Data Editing 110 Gryphon™ I GD4100 Global AIM ID AIM label identifiers (as opposed to custom characters you select yourself as with label identifiers) can be included with scanned barcode data. AIM label identifiers consist of three characters as follows: • A close brace character (ASCII ‘]’), follo wed b y ... • A code character (see the[...]

Global AIM ID Pr oduct Reference Guide 111 Global AIM ID — c o ntinued ENTER/EXIT PROGRAMMING MODE Global AIM ID = Disable Global AIM ID = Enable DEF A UL T[...]

Data Editing 112 Gryphon™ I GD4100 GS1-128 AIM ID If Global AIM ID is disabled, the AIM ID for GS1-128 can be enabled/disabled inde- pendently. The AIM ID for GS1-128 is a ]C1, ]C2 or ]C3. AIM IDs for other symbologies can be enabled/disabled independently as well. Contact Customer Support for assistance If Global AIM ID is disabled, the AIM ID f[...]

Label ID Pr oduct Reference Guide 113 Label ID A Label ID is a customizable code of up to three ASCII characters (each can be one of hex 0x01- 0xFF), used to identify a barcode (symbology) type. It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled. This feature provides options for confi[...]

Data Editing 114 Gryphon™ I GD4100 CODE39 * 2A0000 V 560000 CODE4 4 340000 4 340000 CODE5 j 6A0000 j 6A0000 CODE93 & 260000 U 550000 GS1 D A T ABAR OMNIDIRECTIONAL R4 523400 u 750000 GS1 D A T ABAR EXP ANDED RX 525800 t 740000 GS1 D A T ABAR LIMITED RL 524C00 v 760000 D A T ALOGIC 2OF5 s 730000 s 730000 GS1-128 000000 k 6B0000 EAN13 F 460000 [...]

Label ID Pr oduct Reference Guide 115 Label ID: Set Individually P er S ymbology To configure a Label ID individually for a single symbology: 1. Scan the ENTER/EXIT barcode. 2. Select Label ID position as either BEFORE (Enable as P refix) or AFTER (Enable as suf- fix) by scanning the appropriate barcode in the section "Label ID Control"on[...]

Data Editing 116 Gryphon™ I GD4100 Label ID — con tinued Table 18 STEP A CTION EXAMPLES 1. Scan the ENTER/EXIT barc ode (Scanner enters Pr ogramming Mode) 2. Determine placemen t of the Label ID characters BEFORE or AFTER with regard to scanned data using Label ID Cont rol, starting on page 117 Enable as Prefix Enable as Suffix Enable as Prefix[...]

Label ID Pr oduct Reference Guide 117 Label ID — con tinued Label ID C ontrol This option controls whether a Label ID is disabled, or sent as a prefix or suffix for a given symbology type. ENTER/EXIT PROGRAMMING MODE Label ID T ransmission = Disable Label ID T ransmission = Enable as Prefix Label ID T ransmission = Enable as Suffix CANCEL Make a [...]

Data Editing 118 Gryphon™ I GD4100 Label ID — con tinued Label ID Symbology Selection This option selects the symbology for which a Label ID is to be configured. See "Label ID"on page 113 ENTER/EXIT PROGRAMMING MODE Set UPC-A Label ID Character(s) Set UPC-A/P2 Label ID Character(s) Set UPC-A/P5 Label ID Character(s) Set UPC-A/GS1-128 [...]

Label ID Pr oduct Reference Guide 119 Label ID — con tinued Label ID Symbology Selection — continued This option selects the symbology for which a Label ID is to be configured. See "Label ID"on page 113 for full instructions. ENTER/EXIT PROGRAMMING MODE Set UPC-E/P5 Label ID Character(s) Set UPC-E/GS1-128 Label ID Character(s) Set EAN[...]

Data Editing 120 Gryphon™ I GD4100 Label ID — con tinued Label ID Symbology Selection — continued This option selects the symbology for which a Label ID is to be configured. See "Label ID"on page 113 for full instructions. ENTER/EXIT PROGRAMMING MODE Set EAN 8 Label ID Character(s) Set EAN 8/P2 Label ID Character(s) Set EAN 8/P5 Lab[...]

Label ID Pr oduct Reference Guide 121 Label ID — con tinued Label ID Symbology Selection — continued This option selects the symbology for which a Label ID is to be configured. See "Label ID"on page 113 for full instructions. ENTER/EXIT PROGRAMMING MODE Set GTIN/P5 Label ID Character(s) Set GTIN/GS1-128 Label ID Charac ter(s) Set Data[...]

Data Editing 122 Gryphon™ I GD4100 Label ID — con tinued Label ID Symbology Selection — continued This option selects the symbology for which a Label ID is to be configured. See "Label ID"on page 113 for full instructions. ENTER/EXIT PROGRAMMING MODE Set Code 32 Label ID Character(s) Set Code 128 Label ID Character(s) Set ISBT 128 L[...]

Label ID Pr oduct Reference Guide 123 Label ID — con tinued Label ID Symbology Selection — continued This option selects the symbology for which a Label ID is to be configured. See "Label ID"on page 113 for full instructions. ENTER/EXIT PROGRAMMING MODE Set Standard 2 of 5 La bel ID Character(s) Set Code 4 Label ID Character(s) Set Co[...]

Data Editing 124 Gryphon™ I GD4100 Case C on version This feature allows conversion of the case of all alphabetic characters to upper or lower case. NO TE ENTER/EXIT PROGRAMMING MODE DEF A UL T Case Con version = Disable (no case conversion) Case C o nv ersion = C onv er t to upper case Case C onversion = Con vert to lo wer ca se Case c onv ersio[...]

Character Conversion Pr oduct Reference Guide 125 Character C onv ersion Character conversion is an eight byte configuration item. The eight bytes are 4 character pairs represented in hexadecimal ASCII values. The first character in the pair is the character that will be converted. The second character in the pair is the character to convert to. If[...]

Data Editing 126 Gryphon™ I GD4100 Character C on version — c ontinued ENTER/EXIT PROGRAMMING MODE Configure Character Conv ersion DEF A UL T 0xFFFFFFFFFFFFF FFF[...]

Pr oduct Reference Guide 127 Chapter 12 S ymbologies Introduc tion The reader supports the following symbologies (barcode types). Options for each symbology are included in this chapter. • UPC-A • GS1-128 • UPC-E • Interleav ed 2 of 5 (I 2 of 5) • EAN 13 ( JAN 13) • Datalogic 2 of 5 • EAN 8 (J A N 8) • Codabar • GS1 DataBar™ Omn[...]

Symbologies 128 Gryphon™ I GD4100 Co u p o n Co n t r o l This feature is used to control the reader’s method of processing coupon labels. Options are: • Disable coupon decoding • Enable UPC/EAN coupon decoding • Enable GS1 DataBar coupon decoding To set this feature: 1. Scan the SWIT CH bar code. 2. Scan either the enable or disable barc[...]

UPC-A Pr oduct Reference Guide 129 UPC-A The following options apply to the UPC-A symbology. UPC-A Enable/Disable When disabled, the reader will not re ad UPC-A barcodes. ENTER/EXIT PROGRAMMING MODE UPC-A = Disable UPC-A = Enable UPC-A Check Character T ransmission Enable this option to transmit the check character along with UPC-A barcode data. EN[...]

Symbologies 130 Gryphon™ I GD4100 UPC-A — cont . Expand UPC-A to EAN-13 Expands UPC-A data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. ENTER/EXIT PROGRAMMING MODE UPC-A to EAN-13 = Don ’t Expand UPC-A to EAN-13 = Expand UPC-A Number S yst em Char ac ter T ransmission This[...]

UPC-A Pr oduct Reference Guide 131 UPC-A — cont . UPC-A Minimum Reads This feature specifies the minimum number of consecutive times a UPC-A label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE UPC-A Minimum Reads = 1 UPC-A Minimum Reads = 2 UPC-A Minimum Reads = 3 UPC-A Minimum Reads = 4 DEF A UL T[...]

Symbologies 132 Gryphon™ I GD4100 UPC-E The following options apply to the UPC-E symbology. UPC-E Enable/Disable When disabled, the reader will not read UPC-E barcodes. ENTER/EXIT PROGRAMMING MODE UPC-E = Disable UPC-E = Enable UPC-E Check Character T ransmission Enable this option to transmit the check character along with UPC-E barcode data. EN[...]

UPC-E Pr oduct Reference Guide 133 UPC-E — cont. Expand UPC-E to EAN-13 Expands UPC-E data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. ENTER/EXIT PROGRAMMING MODE UPC-E to EAN-13 = Don’ t Expand UPC-E to EAN-13 = Expand Expand UPC-E to UPC-A Expands UPC-E data to the UPC-A [...]

Symbologies 134 Gryphon™ I GD4100 UPC-E — cont. UPC-E Number S yst em Character T ransmission This feature enables/disables transmission of the UPC-E system number character. ENTER/EXIT PROGRAMMING MODE UPC-E Number System Char acter = Do not transmit UPC-E Number System Character = T ransmit DEF A UL T[...]

UPC-E Pr oduct Reference Guide 135 UPC-E — cont. UPC-E Minimum Reads This feature specifies the minimum number of consecutive times a UPC-E label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE UPC-E Minimum Reads = 1 UPC-E Minimum Reads = 2 UPC-E Minimum Reads = 3 UPC-E Minimum Reads = 4 DEF A UL T[...]

Symbologies 136 Gryphon™ I GD4100 GTIN F ormatting This feature enables/disables the ability to convert UP C-E, UPC-A, EAN 8, and EAN 13 labels into the GTIN 14-character format. NO TE ENTER/EXIT PROGRAMMING MODE GTIN Formatting = Disable GTIN Formatting = Enable If add-on information is present on the base label prior to the co n version taking [...]

EAN 13 Pr oduct Reference Guide 137 EAN 13 The following options apply to the EAN 13 (Jan 13) symbology. EAN 13 Enable/Disable When disabled, the reader will not read EAN 13/JAN 13 barcodes. ENTER/EXIT PROGRAMMING MODE EAN 13 = Disable EAN 13 = Enable EAN 13 Check Character T ransmission Enable this option to transmit the check character along with[...]

Symbologies 138 Gryphon™ I GD4100 EAN 13 — cont . EAN-13 F lag 1 Character Enables/disables transmission of an EAN/JAN13 Flag1 character. The Flag 1 character is the first character of the label. ENTER/EXIT PROGRAMMING MODE EAN-13 Flag 1 Char= Don’ t transmit EAN-13 Flag 1 Char= T ransmit DEF A UL T[...]

EAN 13 Pr oduct Reference Guide 139 EAN-13 ISBN C on v ersion This option enables/disables conversion of EAN 13/JAN 13 Bookland labels starting with 978 to ISBN labels. ENTER/EXIT PROGRAMMING MODE EAN-13 ISBN Con version = Disable EAN-13 ISBN Con version = C onv er t to ISBN DEF A UL T[...]

Symbologies 140 Gryphon™ I GD4100 EAN 13 — cont . EAN 13 Minimum Reads This feature specifies the minimum number of consecut ive times an EAN 13 label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE EAN 13 Minimum Reads = 1 EAN 13 Minimum Reads = 2 EAN 13 Minimum Reads = 3 EAN 13 Minimum Reads = 4 DEF A UL T[...]

EAN 8 Pr oduct Reference Guide 141 EAN 8 The following options apply to the EAN 8 (Jan 8) symbology. EAN 8 Enable/Disable When disabled, the reader will not read EAN 8/JAN 8 barcodes. ENTER/EXIT PROGRAMMING MODE EAN 8 = Disable EAN 8 = Enable EAN 8 Check Character T ransmission Enable this option to transmit the check character along with EAN 8 bar[...]

Symbologies 142 Gryphon™ I GD4100 EAN 8 — cont . Expand EAN 8 to EAN 13 Enable this option to expand EAN 8/JAN 8 labels to EAN 13/JAN 13. ENTER/EXIT PROGRAMMING MODE Expand EAN 8 to EAN 13 = Disable Expand EAN 8 to EAN 13 = Enable DEF A UL T[...]

EAN 8 Pr oduct Reference Guide 143 EAN 8 — cont . EAN 8 Minimum Reads This feature specifies the minimum number of consecutive times an EAN 8 (Jan 8) label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE EAN 8 Minimum Reads = 1 EAN 8 Minimum Reads = 2 EAN 8 Minimum Reads = 3 EAN 8 Minimum Reads = 4 DEF A UL T[...]

Symbologies 144 Gryphon™ I GD4100 UPC/EAN Global Settings This section provides configuration settings for UPC-A, UPC-E, EAN 13 and EAN 8 symbologies, and affects all of these unless otherwise marked for each feature description. UPC/EAN Decoding L ev el Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to ve[...]

UPC/EAN Global Settings Pr oduct Reference Guide 145 UPC/EAN Global Settings — cont . UPC/EAN Decoding L ev el — con t. ENTER/EXIT PROGRAMMING MODE UPC/EAN Decoding Lev el = 1 UPC/EAN Decoding Level = 2 UPC/EAN Decoding Lev el = 3 UPC/EAN Decoding Level = 4 UPC/EAN Decoding Lev el = 5 DEF A UL T[...]

Symbologies 146 Gryphon™ I GD4100 UPC/EAN Global Settings — cont . UPC/EAN C orrela tion When correlation is enabled, the barcode re ader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/ or voids. It may al so help read labels that ha ve damaged areas. En[...]

UPC/EAN Global Settings Pr oduct Reference Guide 147 UPC/EAN Global Settings — cont . UPC/EAN Pric e W eight Check This feature enables/disables calculation and verification of price/weight check digits. Options are • Disabled • Enable 4-digit price-weight c heck-digi t calculation • Enable 5-digit price-weight c heck-digi t calculation •[...]

Symbologies 148 Gryphon™ I GD4100 UPC/EAN Global Settings — cont . In-Stor e Minimum Reads This feature specifies the minimum number of consecut ive times an in-store label must be decoded before it is accepted as good read. In-store labels are defined as UPC-A labels with a number-system character of 2 or 4 as well as EAN 8 and EAN 13 labels w[...]

Add-Ons Pr oduct Reference Guide 149 A dd-Ons The following features apply to optional add-ons. NO TE Optional A dd-ons The reader can be enabled to optionally read the following add-ons (supplementals): •P 2 •P 5 • GS1-128 NO TE ENTER/EXIT PROGRAMMING MODE Optional Add-Ons = Disable P2 Optional Add-Ons = Enable P2 Optional Add-Ons = Disable [...]

Symbologies 150 Gryphon™ I GD4100 Add-Ons — con t. Optional Add-ons — cont . ENTER/EXIT PROGRAMMING MODE Optional Add-Ons = Enable P5 Optional Add-Ons = Disable GS1-128 Optional Add-Ons = Enable GS1-128 DEF A UL T[...]

Add-Ons Pr oduct Reference Guide 151 Add-Ons — con t. Optional Add-On T i mer This option sets the time the reader will look for an add-on wh en an add-on fragment has been seen and optional add-ons are enabled. (Also see "Optional GS1-128 Add-On Timer"on page 154 .) ENTER/EXIT PROGRAMMING MODE Optional Add-on Timer = 10ms Optional Add-[...]

Symbologies 152 Gryphon™ I GD4100 Add-Ons — con t. Optional Add-On T imer — cont . ENTER/EXIT PROGRAMMING MODE Optional Add-on Timer = 60ms Optional Add-on Timer = 70ms Optional Add-on Timer = 100ms Optional Add-on Timer = 120ms Optional Add-on Timer = 140ms Optional Add-on Timer = 160ms DEF A UL T[...]

Add-Ons Pr oduct Reference Guide 153 Add-Ons — con t. Optional Add-On T imer — cont . ENTER/EXIT PROGRAMMING MODE Optional Add-on Timer = 180ms Optional Add-on Timer = 200ms Optional Add-on Timer = 220ms Optional Add-on Timer = 240ms Optional Add-on Timer = 260ms Optional Add-on Timer = 280ms Optional Add-on Timer = 300ms[...]

Symbologies 154 Gryphon™ I GD4100 Add-Ons — con t. Optional GS1-128 Add-On T imer This option sets the timer expiration value to read th e added part after reading the linear EAN/ UPC part. For UPC/EAN add-ons other than those of that type, see "Optional Add-On Timer"on page 151 . ENTER/EXIT PROGRAMMING MODE Optional GS1-128 Add-On Ti[...]

Add-Ons Pr oduct Reference Guide 155 Add-Ons — con t. Optional GS1-128 Add-On T imer — c ont . ENTER/EXIT PROGRAMMING MODE Optional GS1-128 Add-O n Timer = 60ms Optional GS1-128 Add-On Timer = 70ms Optional GS1-128 Add-On Timer = 100ms Optional GS1-128 Add-On Timer = 120ms Optional GS1-128 Add-On Timer = 140ms Optional GS1-128 Add-On Timer = 16[...]

Symbologies 156 Gryphon™ I GD4100 Add-Ons — con t. Optional GS1-128 Add-On T imer — c ont . ENTER/EXIT PROGRAMMING MODE Optional GS1-128 Add-On Timer = 180ms Optional GS1-128 Add-On Timer = 200ms Optional GS1-128 Add-On Timer = 220ms Optional GS1-128 Add-On Timer = 240ms Optional GS1-128 Add-On Timer = 260ms Optional GS1-128 Add-On Timer = 28[...]

Add-Ons Pr oduct Reference Guide 157 Add-Ons — con t. P2 A dd-Ons Minimum Reads This feature specifies the minimum number of times a P2 add-on must be read before it is marked as valid and then combined with a base labe l ENTER/EXIT PROGRAMMING MODE P2 Add-Ons Minimum Reads = 1 P2 Add-Ons Minimum Reads = 2 P2 Add-Ons Minimum Reads = 3 P2 Add-Ons [...]

Symbologies 158 Gryphon™ I GD4100 Add-Ons — con t. P5 A dd-Ons Minimum Reads This feature specifies the minimum number of times a P5 add-on must be read before it is marked as valid and then combined with a base labe l ENTER/EXIT PROGRAMMING MODE P5 Add-Ons Minimum Reads = 1 P5 Add-Ons Minimum Reads = 2 P5 Add-Ons Minimum Reads = 3 P5 Add-Ons M[...]

Add-Ons Pr oduct Reference Guide 159 Add-Ons — con t. GS1-128 A dd-Ons Minimum Reads This feature specifies the minimum number of times an GS1- 128 add-on must be read before it is marked as valid and then combined with a base labe l ENTER/EXIT PROGRAMMING MODE GS1-128 Add-Ons Minimum Reads = 1 GS1-128 Add- Ons Minimum Reads = 2 GS1-128 Add-Ons M[...]

Symbologies 160 Gryphon™ I GD4100 GS1 DataBar™ Omnidirectional The following options apply to the GS1 DataBar™ Omnidirectional (formerly RSS-14) symbology. GS1 DataBar™ Omnidirectional Enable/Disable When disabled, the reader will not read GS1 DataBar™ Omnidirectional barcodes. ENTER/EXIT PROGRAMMING MODE GS1 DataBar™ Omnidirectional = [...]

GS1 DataBar™ Omnidirectional Pr oduct Reference Guide 161 GS1 DataBar™ Omnidirectional — cont. GS1 DataBar™ Omnidirectional Minimum Reads This feature specifies the minimum number of consecutive times a GS1 DataBar™ Omnidirectional label must be decoded before it is accepted as good read ENTER/EXIT PROGRAMMING MODE GS1 DataBar™ Omnidire[...]

Symbologies 162 Gryphon™ I GD4100 GS1 DataBar™ Expanded The following options apply to the GS1 DataBar™ Expanded (formerly RSS Expanded) symbology. GS1 DataBar™ Expanded Enable/Disable When disabled, the reader will not read GS1 DataBar™ Expanded barcodes. ENTER/EXIT PROGRAMMING MODE GS1 DataBar™ Expanded = Disable GS1 DataBar™ Expand[...]

GS1 DataBar™ Expanded Pr oduct Reference Guide 163 GS1 DataBar™ Expanded — cont. GS1 DataBar™ Expanded Minimum Reads This feature specifies the minimum number of consecutive times a GS1 DataBar™ Expanded label must be decoded before it is accepted as good read ENTER/EXIT PROGRAMMING MODE GS1 DataBar™ Expanded Minimum Reads = 1 GS1 DataB[...]

Symbologies 164 Gryphon™ I GD4100 GS1 DataBar™ Expanded — cont. GS1 DataBar™ Expanded L ength C ontrol This feature specifies either variable length decoding or fixed length decoding for the GS1 DataBar™ Expanded symbology. V ariable Length. For variable-length decoding, a minimum length may be set. Fix ed Length. For fixed-length decodin[...]

GS1 DataBar™ Expanded Pr oduct Reference Guide 165 GS1 DataBar™ Expanded — cont. GS1 DataBar™ Expanded Set Length 1 This feature specifies one of the barcode lengths for GS1 DataBar™ Expanded L ength Con trol . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fix ed Le n g t h Mode. Length[...]

Symbologies 166 Gryphon™ I GD4100 GS1 DataBar™ Expanded — cont. GS1 DataBar™ Expanded Set Length 1 — c ont. ENTER/EXIT PROGRAMMING MODE Selec t GS1 Data Bar™ Expanded Set Length 1 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 01 [...]

GS1 DataBar™ Expanded Pr oduct Reference Guide 167 GS1 DataBar™ Expanded — cont. GS1 DataBar™ Expanded Set Length 2 This feature specifies one of the barcode lengths for GS1 DataBar™ Expanded L ength Con trol . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fixe d Le n g th Mode. Length [...]

Symbologies 168 Gryphon™ I GD4100 GS1 DataBar™ Expanded — cont. GS1 DataBar™ Expanded Set Length 2 — c ont. ENTER/EXIT PROGRAMMING MODE Selec t GS1 Data Bar™ Expanded Set Length 2 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 74 [...]

GS1 DataBar™ Limited Pr oduct Reference Guide 169 GS1 DataBar™ Limited The following options apply to the GS1 DataBar™ Limited (formerly RSS Limited) symbology. GS1 DataBar™ Limited Enable/Disable When disabled, the reader will not read GS1 DataBar™ Limited barcodes. ENTER/EXIT PROGRAMMING MODE GS1 DataBar™ Limited = Disable GS1 DataBar[...]

Symbologies 170 Gryphon™ I GD4100 GS1 DataBar™ Limited — cont. GS1 DataBar™ Limited Minimum Reads This feature specifies the minimum number of co nsecutive times a GS1 DataBar™ Limited label must be decoded before it is accepted as good read ENTER/EXIT PROGRAMMING MODE GS1 DataBar™ Limited Minimum Reads = 1 GS1 DataBar™ Limited Minimu[...]

Code 39 Pr oduct Reference Guide 171 C ode 39 The following options apply to the Code 39 symbology. C ode 39 Enable/Disable When disabled, the reader will not read Code 39 barcodes. ENTER/EXIT PROGRAMMING MODE Code 39 = Disable Code 39 = Enable DEF A UL T[...]

Symbologies 172 Gryphon™ I GD4100 C ode 39 — cont . C ode 39 Check Char acter Calculation Enable this option to enables/disables calculation and verification of an optional Code 39 check character. When disabled, any check character in the label is treated as a data character ENTER/EXIT PROGRAMMING MODE Code 39 Check Ch aracter Calculation = D [...]

Code 39 Pr oduct Reference Guide 173 C ode 39 — cont . C ode 39 Check Char acter T ransmission Enable this option to transmit the check character along with Code 39 barcode data. ENTER/EXIT PROGRAMMING MODE Code 39 Check Character T ransmission = Don ’t Send Code 39 Check Character T ransmission = Send C ode 39 Start/Stop Char acter T ransmissi[...]

Symbologies 174 Gryphon™ I GD4100 C ode 39 — cont . C ode 39 F ull ASCII In Code 39 decoding, this enables/disables the translation of Code 39 characters to Code 39 full-ASCII characters. ENTER/EXIT PROGRAMMING MODE Code 39 F ull ASCII = Disable Code 39 F ull ASCII = Enable DEF A UL T[...]

Code 39 Pr oduct Reference Guide 175 C ode 39 — cont . C ode 39 Quiet Zones This feature specifies the number of quiet zones for Cod e 39 labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 time s the width of the narrowest bar or space in the label. ENTER/EXIT PROGRAMMING MODE Code 39 Quiet Zones = Quiet Zone on one[...]

Symbologies 176 Gryphon™ I GD4100 C ode 39 — cont . C ode 39 Minimum Reads This feature specifies the minimum number of consecut ive times a Code 39 label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE Code 39 Minimum Reads = 1 Co de 39 Minimum Reads = 2 Code 39 Minimum Reads = 3 Co de 39 Minimum Reads = 4 DEF A[...]

Code 39 Pr oduct Reference Guide 177 C ode 39 — cont . C ode 39 Decoding L e ve l Decoding Levels are used to configure a barc ode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing Level 1 results in a ver y conser vative decoder at the expense of not being able to read poorly [...]

Symbologies 178 Gryphon™ I GD4100 C ode 39 — cont . C ode 39 Decoding Le v el — con t. ENTER/EXIT PROGRAMMING MODE Code 39 Dec oding Lev el = 1 Code 39 Decoding Level = 2 Code 39 Dec oding Lev el = 3 Code 39 Decoding Level = 4 Code 39 Dec oding Lev el = 5 DEF A UL T[...]

Code 39 Pr oduct Reference Guide 179 C ode 39 — cont . C ode 39 L ength C ontrol This feature specifies either variable length decoding or fixed length decoding for the Code 39 symbology. V ariable Length. For variable length decoding, a minimum and maximum length may be set. Fix ed Length. For fixed length decoding, two different lengths may be [...]

Symbologies 180 Gryphon™ I GD4100 C ode 39 — cont . C ode 39 Set Length 1 This feature specifies one of the barcode lengths for C ode 39 L ength Con trol . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fix ed Le n g th Mode. Length includes the barcode’s data characters only. The length can[...]

Code 39 Pr oduct Reference Guide 181 C ode 39 — cont . Code 39 Set L ength 1 — cont. ENTER/EXIT PROGRAMMING MODE Selec t Code 39 Set Length 1 Settin g Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 02 = Length 1 is 2 Characters[...]

Symbologies 182 Gryphon™ I GD4100 C ode 39 — cont . C ode 39 Set Length 2 This feature specifies one of the barcode lengths for C ode 39 L ength Con trol . Length 2 is the maximum label length if in Va r i a b l e L e n g t h Mode, or the second fixed length if in Fi xed Le n g t h Mode. Length includes the barcode’s check, data, and full-ASC[...]

Code 39 Pr oduct Reference Guide 183 C ode 39 — cont . Code 39 Set L ength 2 — cont. ENTER/EXIT PROGRAMMING MODE Selec t Code 39Length 2 Settin g Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 50 = Length 2 is 50 Characters[...]

Symbologies 184 Gryphon™ I GD4100 C ode 39 — cont . C ode 39 Inter digit Ratio This feature specifies the ratio between an intercharacter space and module for Code 39 labels. ENTER/EXIT PROGRAMMING MODE Code 39 Int erdigit Ratio = Disable Code 39 Inter digit Ratio = 1 Code 39 Interdigit Ratio = 2 Code 39 Inter digit Ratio = 3 Code 39 Interdigit[...]

Code 39 Pr oduct Reference Guide 185 C ode 39 — cont . Code 39 Interdigit Ratio — cont. ENTER/EXIT PROGRAMMING MODE Code 39 Interdigit Ratio = 6 Code 39 Inter digit Ratio = 7 Code 39 Interdigit Ratio = 8 Code 39 Inter digit Ratio = 9 Code 39 Interdigit Ratio = 10[...]

Symbologies 186 Gryphon™ I GD4100 C ode 39 — cont . C ode 39 Char acter Correla tion When correlation is enabled, the barcode re ader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/ or voids. It may al so help read labels that ha ve damaged areas. Enabli[...]

Code 39 Pr oduct Reference Guide 187 C ode 39 Stit ching This option enables/disables stitching for Code 39 labels. When parts of a Code 39 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met. ENTER/EX[...]

Symbologies 188 Gryphon™ I GD4100 C ode 32 The following options apply to the Code 32 (Italian Pharmaceutical Code) symbology. C ode 32 Enable/Disable When disabled, the reader will not read Code 32 barcodes. ENTER/EXIT PROGRAMMING MODE Code 32 = Disable Code 32 = Enable C ode 32 F eature Setting Ex ceptions NO TE DEF A UL T The follo wing featur[...]

Code 32 Pr oduct Reference Guide 189 C ode 32 — cont . C ode 32 Check Char acter T ransmission Enable this option to transmit the check character along with Code 32 barcode data. ENTER/EXIT PROGRAMMING MODE Code 32 Check Character T ransmission = Don ’t Send Code 32 Check Character T ransmission = Send C ode 32 Start/Stop Char acter T ransmissi[...]

Symbologies 190 Gryphon™ I GD4100 C ode 128 The following options apply to the Code 128 symbology. C ode 128 Enable/Disable When disabled, the reader will not read Code 128 barcodes. ENTER/EXIT PROGRAMMING MODE Code 128 = Disable Code 128 = Enable Expand C o de 128 to C ode 39 This feature enables/disables expansion of Code 128 labels to Code 39 [...]

Code 128 Pr oduct Reference Guide 191 C ode 128 — cont . C ode 128 Check Char ac ter T ransmission Enable this option to transmit the check character along with Code 128 barcode data. ENTER/EXIT PROGRAMMING MODE Code 128 Check Char acter T ransmission = D on’ t Send Code 128 Check Character T ransmission = Send C ode 128 F unc tion Character T [...]

Symbologies 192 Gryphon™ I GD4100 C ode 128 — cont . C ode 128 Sub-C o de Change T ransmission Enables/disables the transmission of “Sub-Code exchange” characters (NOT transmitted by standard decoding). ENTER/EXIT PROGRAMMING MODE Code 128 Sub-Code Change T ransmission = Disable Code 128 Sub-C ode Chan ge T ransmis sion = Enable DEF A UL T[...]

Code 128 Pr oduct Reference Guide 193 C ode 128 — cont . C ode 128 Quiet Z ones This feature specifies the number of quiet zones for Code 128 labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 time s the width of the narrowest bar or space in the label. ENTER/EXIT PROGRAMMING MODE Code 128 Quiet Zones = No Quiet Z o[...]

Symbologies 194 Gryphon™ I GD4100 C ode 128 — cont . C ode 128 Minimum Reads This feature specifies the minimum number of consecutive times a Code 128 label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE Code 128 Minimum Reads = 1 Code 128 Minimum Reads = 2 Code 128 Minimum Reads = 3 Code 128 Minimum Reads = 4 D[...]

Code 128 Pr oduct Reference Guide 195 C ode 128 — cont . C ode 128 Decoding L ev el Decoding Levels are used to configure a barc ode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing Level 1 results in a ver y conser vative decoder at the expe nse of not being able to read poor[...]

Symbologies 196 Gryphon™ I GD4100 C ode 128 — cont . C ode 128 Decoding L ev el — cont . ENTER/EXIT PROGRAMMING MODE Code 128 Decoding L evel = 1 Code 128 Decoding L evel = 2 Code 128 Decoding L evel = 3 Code 128 Decoding L evel = 4 Code 128 Decoding L evel = 5 DEF A UL T[...]

Code 128 Pr oduct Reference Guide 197 C ode 128 — cont . C ode 128 L ength C ontr ol This feature specifies either variable length decoding or fixed length decoding for the Code 128 symbology. V ariable Length. For variable length decoding, a minimum and maximum length may be set. Fix ed Length. For fixed length decoding, two different lengths ma[...]

Symbologies 198 Gryphon™ I GD4100 C ode 128 — cont . C ode 128 Set Length 1 This feature specifies one of the barcode lengths for C ode 128 Length C ontr ol . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fix ed Le n g th Mode. Length includes the barcode’s data characters only. The length [...]

Code 128 Pr oduct Reference Guide 199 C ode 128 — cont . C ode 128 Set Length 1 — con t. ENTER/EXIT PROGRAMMING MODE Select Code 128 Set L ength 1 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 01 = Length 1 is 1 Character[...]

Symbologies 200 Gryphon™ I GD4100 C ode 128 — cont . C ode 128 Set Length 2 This feature specifies one of the barcode lengths for C ode 128 Length C ontr ol . Length 2 is the maximum label length if in Va r i a b l e L e n g t h Mode, or the second fixed length if in Fi xed Le n g t h Mode. Length includes the barcode’s data characters only. [...]

Code 128 Pr oduct Reference Guide 201 C ode 128 — cont . C ode 128 Set Length 2 — con t. ENTER/EXIT PROGRAMMING MODE Selec t Code 128 Length 2 S etting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 80 = Length 2 is 80 Characters[...]

Symbologies 202 Gryphon™ I GD4100 C ode 128 — cont . C ode 128 Char ac ter C orr elation When correlation is enabled, the barcode re ader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/ or voids. It may al so help read labels that ha ve damaged areas. En[...]

Code 128 Pr oduct Reference Guide 203 C ode 128 — cont . C ode 128 St itching This option enables/disables stitching for Code 128 labels. When parts of a Code 128 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requi[...]

Symbologies 204 Gryphon™ I GD4100 GS1-128 The following options apply to the GS1-128 symbology. (Also known as USS-128, GS1-128, GTIN-128, UCC- 128, EAN-128.) GS1-128 Enable This option enables/disables the ability of the reader to translate GS1-128 labels to the GS1-128 data format. Options are: • T ransmit GS1-128 labels in Code 128 data form[...]

Interleaved 2 of 5 (I 2 of 5) Pr oduct Reference Guide 205 Interlea ved 2 of 5 (I 2 of 5) The following options apply to the I 2 of 5 symbology. I 2 of 5 Enable/Disable When disabled, the re ader will not read I 2 of 5 barcodes. ENTER/EXIT PROGRAMMING MODE I 2 of 5 = Disable I 2 of 5 = Enable DEF A UL T[...]

Symbologies 206 Gryphon™ I GD4100 Interlea ve d 2 of 5 (I 2 of 5) — con t. I 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional I 2 of 5 check character . ENTER/EXIT PROGRAMMING MODE I 2 of 5 Check Character Calculation = Disab le I 2 of 5 Check Character Calculatio n = Check Standard (Mo[...]

Interleaved 2 of 5 (I 2 of 5) Pr oduct Reference Guide 207 Interlea ve d 2 of 5 (I 2 of 5) — con t. I 2 of 5 Check Character T ransmission Enable this option to transmit the check character along with I 2 of 5 barcode data. ENTER/EXIT PROGRAMMING MODE I 2 of 5 Check Character T ransmission = Don’ t Send I 2 of 5 Check Character T ransmission = [...]

Symbologies 208 Gryphon™ I GD4100 Interlea ve d 2 of 5 (I 2 of 5) — con t. I 2 of 5 Minimum Reads This feature specifies the minimum number of consecutive times an I 2 of 5 label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE I 2 of 5 Minimum Reads = 1 I 2 of 5 Minimum Reads = 2 I 2 of 5 Minimum Reads = 3 I 2 of[...]

Interleaved 2 of 5 (I 2 of 5) Pr oduct Reference Guide 209 Interlea ve d 2 of 5 (I 2 of 5) — con t. 2 of 5 Decoding L ev el NO TE Decoding Levels are used to configure a barc ode symbology decoder to be very aggressive to very conservativ e depending on a partic ular customer’s needs. • Choosing Level 1 results in a ver y conser vative decode[...]

Symbologies 210 Gryphon™ I GD4100 Interlea ve d 2 of 5 (I 2 of 5) — con t. 2 of 5 Decoding Lev e l — cont . ENTER/EXIT PROGRAMMING MODE 2 of 5 Decoding Level = 1 2 of 5 Decoding L ev el = 2 2 of 5 Decoding Level = 3 2 of 5 Decoding L ev el = 4 2 of 5 Decoding Level = 5 DEF A UL T[...]

Interleaved 2 of 5 (I 2 of 5) Pr oduct Reference Guide 211 Interlea ve d 2 of 5 (I 2 of 5) — con t. I 2 of 5 Length C ontrol This feature specifies either variable length decoding or fixed length decoding for the I 2 of 5 symbology. V ariable Length. For variable length decoding, a minimum and maximum length may be set. Fix ed Length. For fixed l[...]

Symbologies 212 Gryphon™ I GD4100 Interlea ve d 2 of 5 (I 2 of 5) — con t. I 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for I 2 of 5 Length C o ntrol . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fix ed Le n g th Mode. The length includes the barcode’s check and[...]

Interleaved 2 of 5 (I 2 of 5) Pr oduct Reference Guide 213 Interlea ve d 2 of 5 (I 2 of 5) — con t. Datalogic 2 of 5 Set Length 1 — c ont. ENTER/EXIT PROGRAMMING MODE Select I 2 of 5 Length 1 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T[...]

Symbologies 214 Gryphon™ I GD4100 Interlea ve d 2 of 5 (I 2 of 5) — con t. I 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for I 2 of 5 Length C o ntrol . Length 2 is the maximum label length if in Va r i a b l e L e n g t h Mode, or the second fixed length if in Fi xed Le n g t h Mode. The length includes the barcode’[...]

Interleaved 2 of 5 (I 2 of 5) Pr oduct Reference Guide 215 Interlea ve d 2 of 5 (I 2 of 5) — con t. I 2 of 5 Set Length 2 — c ont. ENTER/EXIT PROGRAMMING MODE Select I 2 of 5 Length 2 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 50 = Le[...]

Symbologies 216 Gryphon™ I GD4100 Interlea ve d 2 of 5 (I 2 of 5) — con t. I 2 of 5 Character Correlation When correlation is enabled, the barcode re ader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/ or voids. It may al so help read labels that ha ve [...]

Interleaved 2 of 5 (I 2 of 5) Pr oduct Reference Guide 217 Interlea ve d 2 of 5 (I 2 of 5) — con t. I 2 of 5 Stit ching This option enables/disables stitching for I 2 of 5 labels. When parts of a I 2 of 5 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data wil[...]

Symbologies 218 Gryphon™ I GD4100 Interlea ve d 2 of 5 (I 2 of 5) — con t. F ollett 2 of 5 The following options apply to the Follett 2 of 5 symbology. F ollett 2 of 5 Enable/Disable Enables/Disables ability of imager to decode Follett 2 of 5 labels. ENTER/EXIT PROGRAMMING MODE F ollett 2 of 5 = Disable Follett 2 of 5 = Enab le DEF A UL T[...]

Datalogic 2 of 5 Pr oduct Reference Guide 219 Datalogic 2 of 5 The following options apply to the Datalogic 2 of 5 symbology. Datalogic 2 of 5 Enable/Disable When disabled, the reader will not read Datalogic 2 of 5 barcodes. ENTER/EXIT PROGRAMMING MODE Datalogic 2 of 5 = Disable Datalogic 2 of 5 = Enable DEF A UL T[...]

Symbologies 220 Gryphon™ I GD4100 Datalogic 2 of 5 — c ont . Datalogic 2 of 5 Check Char acter Calculation This option enables/disables calculation and verification of an optional Datalogic 2 of 5 check character. ENTER/EXIT PROGRAMMING MODE Datalogic 2 of 5 Check Character Calculation = Disable Datalogic 2 of 5 Check Char acter Calcula tion = [...]

Datalogic 2 of 5 Pr oduct Reference Guide 221 Datalogic 2 of 5 — c ont . Datalogic 2 of 5 Minimum Reads This feature specifies the minimum number of consecutive times an Datalogic 2 of 5 label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE I 2 of 5 Minimum Reads = 1 I 2 of 5 Minimum Reads = 2 I 2 of 5 Minimum Read[...]

Symbologies 222 Gryphon™ I GD4100 Datalogic 2 of 5 — c ont . Datalogic 2 of 5 L ength C o ntrol This feature specifies either variable length decoding or fixed le ngth decoding for the Datalogic 2 of 5 symbology. V ariable Length. For variable length decoding, a minimum and maximum length may be set. Fix ed Length. For fixed length decoding, tw[...]

Datalogic 2 of 5 Pr oduct Reference Guide 223 Datalogic 2 of 5 — c ont . Datalogic 2 of 5 Set L ength 1 This feature specifies one of the barcode lengths for Datalogic 2 of 5 Length C ontr ol . Length 1 is the minimum label length if in Va r i a b l e L e n g t h Mode, or the first fixed length if in Fi xed Le n g t h Mode. The length includes th[...]

Symbologies 224 Gryphon™ I GD4100 Datalogic 2 of 5 — c ont . Datalogic 2 of 5 Set Length 1 — c ont. ENTER/EXIT PROGRAMMING MODE Select Datalog ic 2 of 5 L ength 1 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 06 = Length 1 is 6 Charact[...]

Datalogic 2 of 5 Pr oduct Reference Guide 225 Datalogic 2 of 5 — c ont . Datalogic 2 of 5 Set L ength 2 This feature specifies one of the barcode lengths for Datalogic 2 of 5 Length C ontr ol . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fixe d Length Mode. The length includes th e barcode’[...]

Symbologies 226 Gryphon™ I GD4100 Datalogic 2 of 5 — c ont . Datalogic 2 of 5 Set Length 2 — c ont. ENTER/EXIT PROGRAMMING MODE Select Datalog ic 2 of 5 L ength 2 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 50 = Length 2 is 50 Charac[...]

Datalogic 2 of 5 Pr oduct Reference Guide 227 Datalogic 2 of 5 — c ont . Datalogic 2 of 5 Char acter C orrelation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/ or voids. It may also help read labels that ha[...]

Symbologies 228 Gryphon™ I GD4100 Datalogic 2 of 5 — c ont . Datalogic 2 of 5 Stitching This option enables/disables stitching for Datalogic 2 of 5 labels. When parts of a Datalogic 2 of 5 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded i[...]

Codabar Pr oduct Reference Guide 229 Co d a b a r The following options apply to the Codabar symbology. C odabar Enable/Disable When disabled, the reader will not read Codabar barcodes. ENTER/EXIT PROGRAMMING MODE Codabar = Disable Codabar = Enable DEF A UL T[...]

Symbologies 230 Gryphon™ I GD4100 C odabar — con t. C odabar Check Char acter Calculation Enable this option to enables/disables calculation and verification of an optional Codabar check character. When disabled, any check character in the label is treated as a data character ENTER/EXIT PROGRAMMING MODE Codabar Check Charac ter Calculation = Do[...]

Codabar Pr oduct Reference Guide 231 C odabar — cont . C odabar Check Char acter T ransmission Enable this option to transmit the check character along with Codabar barcode data. ENTER/EXIT PROGRAMMING MODE Codabar Check Character T ransmission = Don’t Send Codabar Check Character T ransmission = Send C odabar Star t/Stop Ch arac ter T ransmiss[...]

Symbologies 232 Gryphon™ I GD4100 C odabar — con t. C odabar St ar t /Stop C harac ter S et This option specifies the format of transmit ted Codabar start/stop characters ENTER/EXIT PROGRAMMING MODE Codabar Check Character Set = ABCD/TN*E Codabar Check Char acter S et = ABCD/ABCD Codabar Check Character Set = abcd/tn*e Codabar Check Character S[...]

Codabar Pr oduct Reference Guide 233 C odabar — cont . C odabar St ar t /Stop C harac ter Match When enabled, this option requires that start and stop characters match ENTER/EXIT PROGRAMMING MODE Codabar Star t/Stop Charac ter Match = D on’ t Require Match Codabar Start/Stop Character Match = Require Match . DEF A UL T[...]

Symbologies 234 Gryphon™ I GD4100 C odabar — con t. C odabar Quiet Z ones This feature specifies the number of quiet zones for Codabar labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 time s the width of the narrowest bar or space in the label. ENTER/EXIT PROGRAMMING MODE Codabar Quiet Zones = Quiet Zone on one [...]

Codabar Pr oduct Reference Guide 235 C odabar — cont . C odabar Minimum Reads This feature specifies the minimum number of consecutive times a Codabar label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE Codabar Minimum Reads = 1 Co dabar Minimum Reads = 2 Codabar Minimum Reads = 3 Co dabar Minimum Reads = 4 DEF A[...]

Symbologies 236 Gryphon™ I GD4100 C odabar — con t. C odabar Decoding Le vel Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing Level 1 results in a ver y conser vative decoder at the expe nse of not being able to read poorly pri[...]

Codabar Pr oduct Reference Guide 237 C odabar — cont . C odabar Decoding Le vel — c ont. ENTER/EXIT PROGRAMMING MODE Codabar Dec oding Lev el = 1 Codabar Dec oding Lev el = 2 Codabar Dec oding Lev el = 3 Codabar Dec oding Lev el = 4 Codabar Dec oding Lev el = 5 DEF A UL T[...]

Symbologies 238 Gryphon™ I GD4100 C odabar — con t. C odabar L ength C ontrol This feature specifies either variable length decoding or fixed length decoding for the Codabar symbology. V ariable Length. For variable length decoding, a minimum and maximum length may be set. Fix ed Length. For fixed length decoding, two different lengths may be s[...]

Codabar Pr oduct Reference Guide 239 C odabar — cont . C odabar Set Length 1 This feature specifies one of the barcode lengths for C odabar Length C ontrol . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fix ed Le n g th Mode. Length includes the barcode’s start, stop, check and data characte[...]

Symbologies 240 Gryphon™ I GD4100 C odabar — con t. C odabar Set Length 1 — cont . ENTER/EXIT PROGRAMMING MODE Select Codabar Length 1 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 03 = Length 1 is 3 Characters[...]

Codabar Pr oduct Reference Guide 241 C odabar — cont . C odabar Set Length 2 This feature specifies one of the barcode lengths for C odabar Length C ontrol . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fi xe d Le n g t h Mode. The length includes the barcode’s start, stop, check and data ch[...]

Symbologies 242 Gryphon™ I GD4100 C odabar — con t. C odabar Set Length 2 — cont . ENTER/EXIT PROGRAMMING MODE Select Codabar Length 2 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 50 = Length 2 is 50 Characters[...]

Codabar Pr oduct Reference Guide 243 C odabar — cont . C odabar Inter digit Ratio This feature specifies the ratio between an intercharacter space and module for Codabar labels. ENTER/EXIT PROGRAMMING MODE Codabar Int erdigit Ratio = Disable Codabar Inter digit Ratio = 1 Codabar In terdigit Ratio = 2 Codabar Inter digit Ratio = 3 Codabar In terdi[...]

Symbologies 244 Gryphon™ I GD4100 C odabar — con t. Codabar Interdigit Ratio — c ont. ENTER/EXIT PROGRAMMING MODE Codabar Int erdigit Ratio = 6 Codabar Inter digit Ratio = 7 Codabar Int erdigit Ratio = 8 Codabar Inter digit Ratio = 9 Codabar Interdigit Ratio = 10[...]

Codabar Pr oduct Reference Guide 245 C odabar — cont . C odabar Char acter C orrelation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/ or voids. It may also help read labels that have damaged areas. Enabling[...]

Symbologies 246 Gryphon™ I GD4100 C odabar Stitching This option enables/disables stitching for Codabar labels. When parts of a Codabar barcode are presented to the reader with this feature enabled, the barcode parts wil l be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met. ENTER/EXI[...]

Code 11 Pr oduct Reference Guide 247 C ode 11 The following options apply to the Code 11 symbology. C ode 11 Enable/Disable When disabled, the reader will not read Code 11 barcodes. ENTER/EXIT PROGRAMMING MODE Code 11 = Disable Code 11 = Enable DEF A UL T[...]

Symbologies 248 Gryphon™ I GD4100 C ode 11 — cont . C ode 11 Check Char acter Calculation This option enables/disables calculation and verification of optional Code 11 check character. ENTER/EXIT PROGRAMMING MODE Code 11 Check Char acte r Calculation = Disable Code 11 Check Character C alculation = C heck C Code 11 Check Character Calculation =[...]

Code 11 Pr oduct Reference Guide 249 C ode 11 — cont . C ode 11 Check Char acter T ransmission This feature enables/disables transmission of an optional Code 11 check character. ENTER/EXIT PROGRAMMING MODE Code 11 Check Character T ransmission = Don ’t Send Code 11 Check Character T ransmission = Send DEF A UL T[...]

Symbologies 250 Gryphon™ I GD4100 C ode 11 — cont . C ode 11 Minimum Reads This feature specifies the minimum number of consecut ive times a Code 11 label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE Code 11 Minimum Reads = 1 Co de 11 Minimum Reads = 2 Code 11 Minimum Reads = 3 Co de 11 Minimum Reads = 4 DEF A[...]

Code 11 Pr oduct Reference Guide 251 C ode 11 — cont . C ode 11 L ength C ontrol This feature specifies either variable length decoding or fixed length decoding for the Code 11 symbology. V ariable Length. For variable length decoding, a minimum and maximum length may be set. Fix ed Length. For fixed length decoding, two different lengths may be [...]

Symbologies 252 Gryphon™ I GD4100 C ode 11 — cont . C ode 11 Set Length 1 This feature specifies one of the barcode lengths for C ode 11 L ength Con trol . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fix ed Le n g th Mode. Length includes the barcod e’s check and data characters. The leng[...]

Code 11 Pr oduct Reference Guide 253 C ode 11 — cont . Code 11 Set L ength 1 — cont. ENTER/EXIT PROGRAMMING MODE Selec t Code 11 Set Length 1 Settin g Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 04 = Length 1 is 4 Characters[...]

Symbologies 254 Gryphon™ I GD4100 C ode 11 — cont . C ode 11 Set Length 2 This feature specifies one of the barcode lengths for C ode 11 L ength Con trol . Length 2 is the maximum label length if in Va r i a b l e L e n g t h Mode, or the second fixed length if in Fi xed Le n g t h Mode. Length includes the barcod e’s check and data character[...]

Code 11 Pr oduct Reference Guide 255 C ode 11 — cont . Code 11 Set L ength 2 — cont. ENTER/EXIT PROGRAMMING MODE Select Code 11 Length 2 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 50 = Length 2 is 50 Characters[...]

Symbologies 256 Gryphon™ I GD4100 C ode 11 — cont . C ode 11 Inter digit Ratio This feature specifies the ratio between an intercharacter space and module for Code 11 labels. ENTER/EXIT PROGRAMMING MODE Code 11 Int erdigit Ratio = Disable Code 11 Inter digit Ratio = 1 Code 11 Interdigit Ratio = 2 Code11 In terd igit Ratio = 3 Code 11 Interdigit[...]

Code 11 Pr oduct Reference Guide 257 C ode 11 — cont . Code 11 Interdigit Ratio — cont. ENTER/EXIT PROGRAMMING MODE Code 11 Interdigit Ratio = 6 Code 11 Inter digit Ratio = 7 Code 11 Interdigit Ratio = 8 Code 11 Inter digit Ratio = 9 Code 11 Interdigit Ratio = 10[...]

Symbologies 258 Gryphon™ I GD4100 C ode 11 Decoding L e ve l Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing Level 1 results in a ver y conser vative decoder at the expe nse of not being able to read poorly printed or damaged la[...]

Code 11 Pr oduct Reference Guide 259 C ode 11 — cont . C ode 11 Decoding Le v el — con t. ENTER/EXIT PROGRAMMING MODE Codabar Dec oding Lev el = 1 Codabar Dec oding Lev el = 2 Codabar Dec oding Lev el = 3 Codabar Dec oding Lev el = 4 Codabar Dec oding Lev el = 5 DEF A UL T[...]

Symbologies 260 Gryphon™ I GD4100 C ode 11 — cont . C ode 11 Char acter Correla tion When correlation is enabled, the barcode re ader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/ or voids. It may al so help read labels that ha ve damaged areas. Enabli[...]

Code 11 Pr oduct Reference Guide 261 C ode 11 Stit ching This option enables/disables stitching for Code 11 labels. When parts of a Code 11 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met. ENTER/EX[...]

Symbologies 262 Gryphon™ I GD4100 Standard 2 of 5 The following options apply to the Standard 2 of 5 symbology. Standar d 2 of 5 Enable/Disable When disabled, the reade r will not read Standard 2 of 5 barcodes. ENTER/EXIT PROGRAMMING MODE Standard 2 of 5 = Disable Standard 2 of 5 = Enable DEF A UL T[...]

Standard 2 of 5 Pr oduct Reference Guide 263 Standard 2 of 5 — c ont. Standar d 2 of 5 Check Char ac ter C alculation This option enables/disables calculation and verification of an optional Standard 2 of 5 check character. ENTER/EXIT PROGRAMMING MODE Standard 2 of 5 Check Character Calculation = Disable Standard 2 of 5 Check Character Calculatio[...]

Symbologies 264 Gryphon™ I GD4100 Standard 2 of 5 — c ont. Standar d 2 of 5 Minimum Reads This feature specifies the minimum number of consecutive times a Stan dard 2 of 5 label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE Standard 2 of 5 Minimum Reads = 1 Standard 2 of 5 Minimum Reads = 2 Standard 2 of 5 Mini[...]

Standard 2 of 5 Pr oduct Reference Guide 265 Standard 2 of 5 — c ont. Standar d 2 of 5 Length C ontrol This feature specifies either variable length decoding or fixed length decoding for the Standard 2 of 5 symbology. V ariable Length. For variable length decoding, a minimum and maximum length may be set. Fix ed Length. For fixed length decoding,[...]

Symbologies 266 Gryphon™ I GD4100 Standard 2 of 5 — c ont. Standar d 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for Standard 2 of 5 Length C ontrol . Length 1 is the minimum label length if in Va r i a b l e L e n g t h Mode, or the first fixed length if in Fi xed Le n g t h Mode. Length includes the barcod e’s chec[...]

Standard 2 of 5 Pr oduct Reference Guide 267 Standard 2 of 5 — c ont. Standard 2 of 5 Set L ength 1 — cont . ENTER/EXIT PROGRAMMING MODE Selec t Standard 2 of 5 L ength 1 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 08 = Length 1 is 8 C[...]

Symbologies 268 Gryphon™ I GD4100 Standard 2 of 5 — c ont. Standar d 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Standard 2 of 5 Length C ontrol . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fixe d Length Mode. Length includes the barcode’s check and data cha[...]

Standard 2 of 5 Pr oduct Reference Guide 269 Standard 2 of 5 — c ont. Standard 2 of 5 Set L ength 2 — cont . ENTER/EXIT PROGRAMMING MODE Selec t Standard 2 of 5 L ength 2 Setting Make a mistake? Scan the CANCEL barcode t o abor t and not sav e the entr y string. Y ou can then star t again at the beginning. CANCEL DEF A UL T 50 = Length 2 is 50 [...]

Symbologies 270 Gryphon™ I GD4100 Standard 2 of 5 — c ont. Standard 2 of 5 Char ac ter Correla tion When correlation is enabled, the barcode re ader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/ or voids. It may al so help read labels that ha ve damage[...]

Standard 2 of 5 Pr oduct Reference Guide 271 Standar d 2 of 5 Stitching This option enables/disables stitching for Standard 2 of 5 labels . When parts of a Standard 2 of 5 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofin[...]

Symbologies 272 Gryphon™ I GD4100 ISB T 128 The following options apply to the ISBT 128 symbology. ISB T 128 Enable/Disable When disabled, the imager will not read ISBT barcodes. ENTER/EXIT PROGRAMMING MODE ISBT 128 = Disable ISBT 128 = Enable ISB T 128 C oncatena tion Use this option to enable/disable ISBT128 concatenation of 2 labels . ENTER/EX[...]

ISBT 128 Pr oduct Reference Guide 273 ISB T 128 — cont . ISB T 128 F orce C oncatena tion When enabled, this feature forces concatenation for ISBT. NO TE ENTER/EXIT PROGRAMMING MODE ISBT 128 F orc e Conca tenation = Disable ISBT 128 For ce Concatenation = Enable ISB T 128 A dv anced C oncatena tion Options NO TE This option is only valid when ISB[...]

Symbologies 274 Gryphon™ I GD4100 C ode 4 The following options apply to the Code 4 symbology. C ode 4 Enable/Disable Enables/Disables ability of imager to decode Code 4 labels. ENTER/EXIT PROGRAMMING MODE Code 4 = Disable Code 4 = Enable DEF A UL T[...]

Code 4 Pr oduct Reference Guide 275 Co d e 4 — co n t . C ode 4 Check Char acter T ransmission This feature enables/disables transmission of an optional Code 4 check character. ENTER/EXIT PROGRAMMING MODE Code 4 Check Character T ransmission = Don’t Send Code 4 Check Char acter T ransmission = Send Co d e 4 H ex t o D e c i m a l Co nve r s i o[...]

Symbologies 276 Gryphon™ I GD4100 C ode 5 The following options apply to the Code 5 symbology. C ode 5 Enable/Disable Enables/Disables ability of imager to decode Code 5 labels. ENTER/EXIT PROGRAMMING MODE Code 5 = Disable Code 5 = Enable DEF A UL T[...]

Code 5 Pr oduct Reference Guide 277 Co d e 5 — co n t . C ode 5 Check Char acter T ransmission This feature enables/disables transmission of an optional Code 5 check character. ENTER/EXIT PROGRAMMING MODE Code 5 Check Character T ransmission = Don’t Send Code 5 Check Char acter T ransmission = Send Co d e 5 H ex t o D e c i m a l Co nve r s i o[...]

Symbologies 278 Gryphon™ I GD4100 C ode 4 and Code 5 C ommon C onfigur ation Items The following options apply to both Code 4 and Code 5 symbologies. C ode 4 and 5 Decoding L ev el Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing[...]

Code 4 and Code 5 Common Configuration Items Pr oduct Reference Guide 279 C ode 4 and C ode 5 C ommon C o nfigura tion Items — c ont. Code 4 and 5 Dec oding Lev e l — cont. ENTER/EXIT PROGRAMMING MODE Code 4 and Code 5 Decoding Lev el = 1 Code 4 and Code 5 Decoding Le v el = 2 Code 4 and Code 5 Decoding Lev el = 3 Code 4 and Code 5 Decoding Le [...]

Symbologies 280 Gryphon™ I GD4100 C ode 4 and C ode 5 C ommon C o nfigura tion Items — con t. C ode 4 and C ode 5 M inimum Reads This feature specifies the minimum num ber of consecutive times a Cod e 4 or Code 5 label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE Code 4 or Code 5 Minimum Reads = 1 Code 4 or Co[...]

Pr oduct Reference Guide 281 Appendix A T echnical Specifica tions Table 35 contains Physical and Performance Characteristics, User Environment and Regulatory information. Table 36 provides Standard Cable Pinouts. Table 35. Technical Specifications Item Description Phys ical Characteristics Colo r White/Gray Gray/Gra y Dimensions Height 7.1” /181[...]

Technical Specifications 282 Gryphon™ I GD4100 (a) T ypical inpu t current measured under factory default configuration. (b) See "Interface Selection" on page 17 for a listing of av ailable interf ace sets by model type. (c) 13 mils DOF based on EAN. All others are Code 39. All labels grade A, typical  environmental light, 20°C , la[...]

Technical Specifications Pr oduct Reference Guide 283 Standar d Cable Pinouts Fig u r e 1 0 and Table 36 provide standard pinout information for the Base Station’s interface cable. Figure 10. Standard Cable Pinouts Pin 10 Cable Clip (Latch) T o Host Cable Cable Strain Relief Bottom of Scanner Interface Cable Port Pin 1 The signal descriptions in [...]

Technical Specifications 284 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 285 Appendix B LED and Beeper Indications The reader’s beeper sounds and its LED illuminates to indicate various functions or errors on the reader. An optional “Green Spot” also performs useful functions. The tables below list these indications. One exception to the behaviors listed in the tables is that the reader’[...]

INDICA TION DESCRIPTION LED BEEPER P ow er-up Beep The r eader is in the process of pow- ering-up . Reader beeps four times a t highest fr eq uency and volume upon pow er- up . Good Read Beep A label has been successfully scanned b y the reader . LED behavior for this indica- tion is configurable via the fea tu re “ Good Read: When to Indi cate ?[...]

LED and Beeper Indications Pr oduct Reference Guide 287 Error C odes Upon startup, if the reader sounds a long tone, this means the reader has not passed its automatic Selftest and has entered FRU (Field Re placeable Unit) isolation mode. If the reader is reset, the sequence will be repeated. The following table describes the LED flashes/beep codes[...]

LED and Beeper Indications 288 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 289 Appendix C Standar d Defaults The most common configuration settings are listed in the “Default” column of the table below. Page references are also provided for feature descriptions and programming barcodes for each parameter. A column has also been provided for recording of your preferred default settings for thes[...]

Standard Defaults 290 Gryphon™ I GD4100 Data Bits 8 Data Bits 54 Stop Bits 1 Stop Bit 55 Pa r i t y None 56 Handshaking Con trol Disable 57 RS-232/USB-COM RTS/CT S Scan C ontrol — RT S is asserted during transmissions. CTS ga tes transmis- sions and controls enable and disable state of scanner . No Delay 57 Beep On AS CII BEL Disable 62 Beep On[...]

Standard Defaults Pr oduct Reference Guide 291 Global Prefix/Suffix No Global Prefix Global Suffix = 0x0D (CR) 108 Global AIM ID Disable 110 Label ID Contr ol Disable 117 Case Conver sion Disable 124 Character Con version No Char Con version 125 Symbologies UPC-A UPC-A Enable/Disable Enable 129 UPC-A Check Character T ransmission Enable 129 Expand [...]

Standard Defaults 292 Gryphon™ I GD4100 EAN 8 Enable/Disable Enable 141 EAN 8 Check Character T ransmission Send 141 Expand EAN 8 to EAN 13 Disable 142 EAN 8 Minimum Reads 11 4 3 UPC/EAN Global Settings UPC/EAN Decoding Lev el 31 4 4 UPC/EAN Corr elation Disable 146 Disable 146 UPC/EAN Pric e W eight Check Disable 147 Add-Ons Optional Add-ons Dis[...]

Standard Defaults Pr oduct Reference Guide 293 GS1 DataBar™ Limited Enable/Disable Disable 169 GS1 DataBar™ Limited GS1-128 Emula- tion Disable 169 GS1 DataBar™ Limited Minimum Reads 11 7 0 Code 39 Code 39 Enable/Disable Enable 171 Code 39 Check Character Calculation Calc ulate 1 72 Code 39 Check Character T ransmission Send 173 Code 39 Star [...]

Standard Defaults 294 Gryphon™ I GD4100 Code 128 Dec oding L evel 31 9 5 Code 128 L ength Control V ariable 197 Code 128 Set L ength 1 11 9 8 Code 128 Set L ength 2 80 20 0 Code 128 Character C orrelation Disable 202 Code 128 Stit ching Enable 203 GS1-128 GS1-128 Enable T ransmit in Code 128 Data F ormat 204 ISBT 128 ISBT 128 Enable/Disable Disab[...]

Standard Defaults Pr oduct Reference Guide 295 Datalogic 2 of 5 Set L ength 2 100 225 Datalogic 2 of 5 Character C orrela tion Disable 227 Datalogic 2 of 5 Stitching Disable 228 Codabar Codabar Enable/Disable Disable 229 Codabar Check Char acter Calculation Don ’t Cal culat e 230 Codabar Check Char acter T ransmission Send 231 Codabar Star t/Stop[...]

Standard Defaults 296 Gryphon™ I GD4100 Code 11 Stit ching Disable 261 Standard 2 of 5 Standard 2 of 5 Enable/Disable Disable 262 Standard 2 of 5 Check Character Calcula- tion Disable 263 Standard 2 of 5 Check Character T rans- mission Send 263 Standard 2 of 5 Minimum Reads 12 6 4 Standard 2 of 5 Decoding Level 32 6 4 Standard 2 of 5 Length Contr[...]

Pr oduct Reference Guide 297 Appendix D Sample Barcodes The sample barcodes in this appendix are ty pical representations for their symbology types. UPC-A EAN-13 Code 39 Code 128 0 1 2 3 4 5 6 7 8 9 0 5 3 4 5 6 7 8 9 0 1 2 3 4 0 123ABC 12345678901234567890123456789012345678901234[...]

Sample Barcodes 298 Gryphon™ I GD4100 Sample Barc odes — c ontinued Interleaved 2 of 5 Code 32 Codabar Code 93 Code 1 1 12345678901231 00246897634 5765485 7554628485[...]

Sample Barcodes Pr oduct Reference Guide 299 GS1 DataBar™ (RSS) NO TE GS1 DataBar™-14 GS1 DataBar™ v ariants must be enabled to r ead the barc odes below (see GS1 DataBar™ (RSS) on page 299 ). 10293847560192 83746501928374 60294784503665 23 (GS1 DataBar™ Expanded St acke d) 1234890hjio9900mnb (GS1 DataBar™ Expanded) 0867234565091 6 (GS1[...]

Sample Barcodes 300 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 301 Appendix E K eypad Use the barcodes in this appendix to enter numbers as you would selec t digits/characters from a keypad. 0 1 2 3 4 5[...]

Keypad 302 Gryphon™ I GD4100 6 7 8 9[...]

Keypad Pr oduct Reference Guide 303 A B C D E F[...]

Keypad 304 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 305 Appendix F Sc ancode T ables C ontrol Char ac ter Emulation Control character emulation selects from different scancode tables as listed in this appendix. Each of the control character sets below are detailed by interface type in the tables. These apply to Wedge and USB Keyboard platforms. C ontrol Char acter 00 . Chara[...]

306 Gryphon™ I GD4100 Inter face T ype PC A T PS/2 or USB-K eyboard T able F-1. Scancode Set When Control Char acter is 00 or 01 Extended characters (sky blue) are sent through dedicat ed keys (when av ailable in the selected country mode) or by using an Al t Mode sequence.[...]

Product Reference Guide 307 Inter face T ype PC A T PS/2 or USB-Keyboar d — cont . T able F-2. Scancode Set When Control Char acter is 02[...]

308 Gryphon™ I GD4100 Inter face type PC A T PS/2 Alt Mode or USB-K eyboard A lt Mode T able F-3. Scancode Set When Control Char acter is 00 or 01[...]

Product Reference Guide 309 Inter face type PC A T PS/2 Alt Mode or USB-Keyboar d Alt Mode — cont . T able F-4. Scancode Set When Control Char acter is 02[...]

310 Gryphon™ I GD4100 Digital Inter face T able F-5. Scancode Set When Control Char acter is 00 or 01[...]

Product Reference Guide 311 Digital Inter face — c o nt . T able F-6. Scancode Set When Control Char acter is 02[...]

312 Gryphon™ I GD4100 IBM31xx 102-ke y T able F-7. Scancode Set When Control Char acter is 00 or 01[...]

Product Reference Guide 313 IBM31xx 102-k ey — cont . T able F-8. Scancode Set When Control Char acter is 02[...]

314 Gryphon™ I GD4100 IBM XT T able F-9. Scancode Set When Control Char acter is 00 or 01[...]

Product Reference Guide 315 IBM XT — cont . T able F-10. Scancode Set When Control Char acter is 02[...]

316 Gryphon™ I GD4100 Microsof t Windo ws C odepage 1252 Windows-1252 is a character encoding of the Latin alphabet, used by default in the legacy components of Microsoft Windows in En glish and some other Western languages.[...]

Scancode Tables Pr oduct Reference Guide 317 NO TES[...]

Scancode Tables 318 Gryphon™ I GD4100 NO TES[...]

Pr oduct Reference Guide 319 Index B barcodes cancel 301 numeric barcodes 301 RS-232 baud rate 91 RS-232 parameters parity 82 , 218 ,2 7 2 ,2 7 4 ,2 7 6 ,2 7 9 Beeper Pitch, Good Read 31 ,3 2 Volume, Good Read 34 Beeper, Good Read 29 C Cable Pinouts 283 Clear to Send 57 Code 39 Format 99 Conversion, case 124 Conversion, character 125 Convert to Cod[...]

320 Gryphon™ I GD4100 Index P Performance Characteristics 281 Physical Characteristics 281 Pitch – Good Read, Beeper 31 ,3 2 Polarity (wand) 102 Prefix/Suffix 108 Product Specifications 281 Programming Barcodes 14 R Read, Beeper – Good 29 Read, Beeper Pitch – Good 31 ,3 2 Read, Beeper Volume – Good 34 Request to Send 57 RS-232 interface s[...]

ASCII Char t ASCII Char . He x No . ASCII Char . He x No . ASCII Char . He x No . ASCII Char . He x No . NUL SOH STX ETX EO T ENQ AC K BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F SP ! “ # $ % & ’ ( ) * +[...]

Datalogic Scanning, Inc. 959 T err y Street Eugene, OR 97402 USA T elephone: (541) 683-5700 F ax: (541) 345-7140 ww w .scanning .datalogic.com Austr alia Datalogic Scanning Pt y Ltd T elephone: [61] (2) 9870 3200 australia.scanning@datalogic .com F rance and Benelux Datalogic Scanning Sarl T elephone: [33].01.64.86.71.00 france.scanning@da talogic.[...]