Dell D07S Bedienungsanleitung

Dell Precision T1700 Small Form Factor Owner's Manual Regulatory Model: D07S Regulatory Type: D07S001[...]

Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2013 Dell Inc[...]

Contents 1 Working on Your Computer....................................................................................................... 5 Before Working Inside Your Computer ..................................................................................................................... 5 Turning Off Your Computer ...........................[...]

Removing the Coin-Cell Battery .............................................................................................................................. 24 Installing the Coin-Cell Battery ............................................................................................................................... 25 Removing the Heat Sink As[...]

1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that[...]

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components. Turning Off Your Computer CAUTION: To avoid losing data, s[...]

2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe System Overview The figure below displays[...]

6. drive cage 7. optical drive 8. power switch 9. input/output (I/O) Panel 1. memory module 2. speaker 3. front bezel 4. system fan Removing the Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Pull up the cover-release latch at the side of the computer. 8[...]

3. Lift the cover upward to a 45–degree angle and remove it from the computer. Installing the Cover 1. Place the cover on the chassis. 2. Press down on the cover till it clicks into place. 3. Follow the procedures in After Working Inside Your Computer . Removing the Front Bezel 1. Follow the procedures in Before Working Inside Your Computer . 2. [...]

Installing the Front Bezel 1. Insert the hooks along the bottom edge of the front bezel into the slots on the chassis front. 2. Push the bezel toward the computer to engage the front bezel retention clips until they click into place. 3. Install the cover. 4. Follow the procedures in After Working Inside Your Computer . Removing The Expansion Card 1[...]

Installing The Expansion Card 1. Insert the expansion card into the connector on the system board and press down to secure it in place. 2. Install the cover 3. Follow the procedures in After Working Inside Your Computer . Removing the Wireless Local Area Network (WLAN) Card 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove[...]

5. Press the blue tab and lift the latch outwards. Lift and remove the WLAN card from the connector on the system board. Installing the WLAN Card 1. Place the WLAN card on the connector and press down. 2. Press the latch to secure the WLAN card. 3. Place the antenna puck on the connector and tighten the screws that secure it to the computer. 4. Ins[...]

Removing the Optical Drive 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the cover. 3. Disconnect the data and power cables from the back of the optical drive. 4. Lift the tab and slide the optical drive out to remove it from the computer. 5. Flex the optical-drive bracket and then lift the optical drive from the brack[...]

Removing the Drive Cage 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a. cover b. front bezel c. optical drive 3. Disconnect the data and the power cables from the back of the hard drive. 4. Slide the blue drive-cage handle toward unlock position and lift the hard drive cage from the computer. Installing the Drive[...]

3. Flip over the drive cage and insert it into the chassis. The drive cage tabs are secured by the slots in the chassis. 4. Slide the drive-cage handle toward the locked position. 5. Install the: a. front bezel b. optical drive c. cover 6. Follow the procedures in After Working Inside Your Computer . Removing the Hard Drive 1. Follow the procedures[...]

NOTE: Perform step 5 only if you have a mini hard drive. Installing the Hard Drive 1. Tighten the screws to secure the mini hard drive (if available) to the hard-drive bracket. 2. Flex the hard-drive bracket and then insert the hard drive into the bracket. 3. Slide the hard-drive bracket into the drive cage. 4. Install the: a. drive cage b. optical[...]

a. drive cage b. optical drive c. cover 5. Follow the procedures in After Working Inside Your Computer . Removing the Intrusion Switch 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the cover. 3. Press the clip inwards to release and gently pull the intrusion cable from system board. 4. Slide the intrusion switch toward[...]

NOTE: The memory sockets in your computer may be labeled differently depending on the hardware configuration. For example, A1, A2 or 1,2,3. • If the quad-rank memory modules are mixed with single or dual-rank modules, the quad-rank modules must be installed in the sockets with the white release levers. • If memory modules with different speeds [...]

4. Pry and remove the system fan away from the grommets securing it to the front of the computer. Then, press the grommets inward along the slots and pass through the chassis. Installing the System Fan 1. Place the system-fan in the chassis. 2. Pass the grommets through the chassis and slide outward along the groove to secure it in place. 3. Connec[...]

Removing the Power Switch 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a. cover b. front bezel c. optical drive d. drive cage 3. Disconnect the power-switch cable from the system board. 4. Press the clips on both side of the power switch to release it from the chassis and remove the power switch along with its ca[...]

3. Install the: a. drive cage b. optical drive c. front bezel d. cover 4. Follow the procedures in After Working Inside Your Computer . Removing the Input/Output (I/O) Panel 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a. cover b. front bezel c. optical drive d. drive cage 3. Disconnect and un-thread the I/O pane[...]

Installing the Input/Output (I/O) Panel 1. Insert the I/O panel into the slot on the chassis front. 2. Slide the I/O panel to secure it to the chassis. 3. Tighten the screw to secure the I/O panel to the chassis. 4. Connect the I/O panel or FlyWire cable and audio cable to the system board. 5. Thread the I/O panel or FlyWire cable into the fan-shel[...]

5. Remove the screws that secure the power supply to the back of the computer. 6. Push in on the blue release tab beside the power supply, and slide the power supply towards the front of the computer. 7. Lift the power supply out of the computer 23[...]

Installing the Power Supply 1. Place the power supply in the chassis and slide towards the back of the computer to secure it. 2. Tighten the screws securing the power supply to the back of the computer. 3. Connect the 4-pin and 8–pin power cables to the system board. 4. Thread the power cables into the chassis clips. 5. Install the: a. drive cage[...]

Installing the Coin-Cell Battery 1. Place the coin-cell battery into its slot on the system board. 2. Press the coin-cell battery downward until the release latch springs back into place and secures it. 3. Install the: a. drive cage b. front bezel c. cover 4. Follow the procedures in After Working Inside Your Computer . Removing the Heat Sink Assem[...]

Installing the Heat Sink Assembly 1. Place the heat-sink assembly into the chassis. 2. Tighten the captive screws to secure the heat-sink assembly to the system board. 3. Connect the fan cable to the system board. 4. Place the fan shroud on the fan and push to click in place. 5. Install the cover 6. Follow the procedures in After Working Inside You[...]

Installing the Processor 1. Insert the processor into the processor socket. Ensure the processor is properly seated. 2. Gently lower the processor cover. 3. Press the release lever down and then move it inward to secure it with the retention hook. 4. Install the heat-sink assembly. 5. Install the cover. 6. Follow the procedures in After Working Ins[...]

Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a. cover b. front bezel c. optical drive d. drive cage e. memory f. heat sink assembly g. expansion card(s) h. power supply 3. Disconnect all the cables connected to the system board, and move the cables away from the chassis. 4. Remove the sc[...]

g. front bezel h. cover 5. Follow the procedures in After Working Inside Your Computer . 29[...]

3 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardware • View the system hardware configuration • Enable or disable integrated devices • Set performance and power management thresholds • Manage[...]

Table 1. Navigation Keys Keys Navigation Up arrow Moves to the previous field. Down arrow Moves to the next field. <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable. <Tab> Moves to the next focus area. NOTE: For th[...]

Option Description Date/Time Allows you to set the date and time. The changes to the system date and time takes effect immediately. Table 3. System Configuration Option Description Integrated NIC Allows you to enable or disable the integrated network card. You can set the integrated NIC to: • Disabled • Enabled • Enabled w/PXE (this option is[...]

Option Description SMART Reporting This field controls if the hard drive errors for the integrated drives are reported during system startup. This technology is part of the SMART (Self Monitoring Analysis and Reporting Technology) specification. • Enable SMART Reporting - This option is disabled by default. USB Configuration This field configures[...]

Option Description • System Password Max Password Bypass Allows you to bypass the System Password and the internal HDD password prompts during a system restart. • Disabled - Always prompt for the system and internal HDD password when they are set. This option is disabled by default. • Reboot Bypass - Bypass the password prompts on restarts (w[...]

Option Description This option is set to Enable by default. Admin Setup Lockout Allows you to enable or disable the option to enter setup when an admin password is set. • Enable Admin Setup Lockout - This option is not set by default. Table 5. Secure Boot Secure Boot Enable Allows you to enable or disable Secure Boot feature • Disable • Enabl[...]

Option Description C States Control Allows you to enable or disable the additional processor sleep states. This option is enabled by default. Limit CPUID Value This field limits the maximum value the processor Standard CPUID Function will support • Enable CPUID Limit (this option is disabled by default) NOTE: Some Operating system will not comple[...]

Option Description NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if Auto Power is set to disabled . Deep Sleep Control Allows you to define the controls when Deep Sleep is enabled. • Disabled • Enabled in S5 only • Enabled in S4 and S5 This option is disabled by default.[...]

Option Description • Enable MEBx Hotkey — This option is enabled by default Table 9. Virtualization Support Option Description Virtualization This option specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Intel Virtualization technology. • Enable Intel Virtualization Technology - Thi[...]

Option Description NOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServer . Client Address Method Specifies how the client obtains the IP address. • Static IP • DHCP (enabled by default) NOTE: This field is only relevant when the Integrated NIC control in the System[...]

4. Enter the Service Tag or Express Service Code and click Submit . 5. If you are unable to locate or find the Service Tag, click the Product Category of your computer. 6. Choose the Product Type from the list. 7. Select your computer model and the Product Support page of your computer appears. 8. Click Drivers & Downloads . 9. On the Drivers a[...]

To enter a system setup, press <F2> immediately after a power-on or reboot. 1. In the System BIOS or System Setup screen, select System Security and press <Enter>. The System Security screen appears. 2. In the System Security screen, verify that Password Status is Unlocked . 3. Select System Password , enter your system password, and pr[...]

3. Identify the PSWD jumper on the system board. 4. Remove the PSWD jumper from the system board. NOTE: The existing passwords are not disabled (erased) until the computer boots without the jumper. 5. Install the cover. NOTE: If you assign a new system and/or setup password with the PSWD jumper installed, the system disables the new password(s) the[...]

4 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel [...]

5 Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Power LED Diagnostics The power button LED located on the front of the chassis also functions as a bicolored diagnostic LED. The diagnostic LED is only active and visible du[...]

Amber LED State Description 3,7 some other failure with messages on screen Beep Code The computer can emit a series of beeps during start-up if the display does not show errors or problems. These series of beeps, called beep codes, identify various problems. The delay between each beep is 300 ms, the delay between each set of beeps is 3 sec, and th[...]

Error Message Description Decreasing available memory One or more memory modules may be faulty or improperly seated. Re-install the memory modules and, if necessary, replace them. Diskette drive 0 seek failure A cable may be loose or the computer configuration information may not match the hardware configuration. Diskette read failure The floppy di[...]

Error Message Description Memory double word logic failure at address, read value expecting value A memory module may be faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them. Memory odd/even logic failure at address, read value expecting value A memory module may be faulty or improperly seated. Reinstall the mem[...]

Error Message Description Time-of-day not set- please run the System Setup program The time or date stored in System Setup does not match the computer clock. Timer chip counter 2 failed A chip on the system board may be malfunctioning. Unexpected interrupt in protected mode The keyboard controller may be malfunctioning or a memory module may be loo[...]

6 Specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) → Help and Support , and then select the option to view information about your computer. Table 15. Processor Feature Specification Processor type • Intel Core i3 series • Intel Core i5 series • Int[...]

Table 19. Network Feature Specification Integrated Intel I217LM Ethernet capable of 10/100/1000 Mb/s communication Table 20. System Information Feature Specification System chipset Intel C226 chipset DMA Channels two 8237 DMA controllers with seven independently programmable channels Interrupt Levels Integrated I/O APIC capability with 24 interrupt[...]

Feature Specification Small Form Factor one slim optical drive bay Internally Accessible: 3.5-inch SATA drive bays 2.5-inch SATA drive bays Mini-Tower two four Small Form Factor one two Table 24. External Connectors Feature Specification Audio: Front Panel one microphone connector and one headphone connector Back Panel one line-out connector and on[...]

Feature Specification Mini-Tower, Small Form Factor one 164-pin connector Serial ATA: Mini-Tower four 7-pin connectors Small Form Factor three 7-pin connectors Memory four 240-pin connectors Internal USB: Mini-Tower one 10-pin connector Small Form Factor none System Fan one 5-pin connector Front panel control: Mini-Tower one 6–pin and two 20–pi[...]

Feature Specification Orange — a good 1000 Mbps connection exists between the network and the computer. Off (no light) — the computer is not detecting a physical connection to the network. Network activity light on integrated network adapter Yellow light — A blinking yellow light indicates that network activity is present. Power supply diagno[...]

Feature Specification Storage 5 percent to 95 percent (non-condensing) Maximum vibration: Operating 0.26 GRMS Storage 2.20 GRMS Maximum shock: Operating 40 G Storage 105 G Altitude: Operating –15.2 m to 3048 m (–50 to 10,000 ft) Storage –15.20 m to 10,668 m (–50 ft to 35,000 ft) Airborne contaminant level G1 or lower as defined by ANSI/ISA-[...]

7 Contacting Dell NOTE: Dell provides several online and telephone-based support and service options. If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Availability varies by country and product, and some services may not be available in your are[...]