Dodge 2009 Bedienungsanleitung

2009 CHALL ENGER CHAL LENGER Chrysler LL C 81-226-0916 Second Edition Printed in U.S.A. OWNER ’S MANU AL 2009 147914 Dodge LC22 Challenger.indd 1 9/8/08 3:39:42 PM[...]

VEHICLES SOLD IN CANADA W ith r espect to any V ehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor . DRIVING AND ALCOHOL Drunken driving is one of the most fr equent causes of accidents. Y our driving ability can be seriously impaired with blood alcohol levels [...]

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION .............................................................3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................... 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ............................... 7 1 4 UNDERST ANDING YOUR INSTRUMENT P ANEL ..................................[...]

[...]

INTRODUCTION CONTENTS 䡵 Introduction .......................... 4 䡵 How T o Use This Manual ................. 4 䡵 W arnings And Cautions .................. 6 䡵 V ehicle Identification Number ............. 6 䡵 V ehicle Modifications/Alterations ........... 7 1[...]

INTRODUCTION This Owner’s Manual has been prepar ed with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a W arranty Information Booklet and various customer-oriented documents. Y ou are urged to r ead these publications carefully . Following the ins[...]

INTRODUCTION 5 1[...]

W ARNINGS AND CAUTIONS This Owner’s Manual contains W ARNINGS against op- erating procedur es that could result in an accident or bodily injury . It also contains CAUTIONS against proce- dures that could r esult in damage to your vehicle. If you do not read this entir e manual, you may miss important information. Observe all W arnings and Caution[...]

VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. INTRODUCTION 7 1[...]

[...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................ 1 2 ▫ W ireless Ignition Node (WIN) ........... 1 2 ▫ FOB W ith Integrated Key .............. 1 3 ▫ Ignition Key Removal ................. 1 3 ▫ Key-In-Ignition Reminder .............. 1 4 䡵 Sentry Key 威 ......................... 1 5 ▫[...]

▫ T o Open The T runk .................. 2 4 ▫ Using The Panic Alarm ................ 2 4 ▫ Programming Additional T ransmitters ..... 2 5 ▫ T ransmitter Battery Service ............. 2 5 ▫ General Information .................. 2 6 䡵 Remote Starting System ................. 2 6 ▫ How T o Use Remote Start .............. 2 6 䡵 Door L[...]

▫ Event Data Recorder (EDR) ............. 5 6 ▫ Child Restraint ...................... 5 8 䡵 Engine Break-In Recommendations ......... 6 7 䡵 Safety T ips .......................... 6 8 ▫ T ransporting Passengers ............... 6 8 ▫ Exhaust Gas ........................ 6 8 ▫ Safety Checks Y ou Should Make Inside The V ehicle ........[...]

A WORD ABOUT YOUR KEYS Y our vehicle uses a keyless ignition system. This system consists of a Fob with Integrated Key and a W ireless Ignition Node (WIN) with an integral ignition switch. Y ou can insert the double-sided integrated key into the ignition switch with either side up. Keyless Go Feature This vehicle may be equipped with the Keyless Go[...]

Fob With Integrated Key The Fob with Integrated Key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) trans- mitter and a valet key , which stores in the rear of the Fob. The valet key allows for entry into the vehicle should the battery in the vehicle or the Fob go dead. The valet key is also for locking the glove box. [...]

NOTE: The power window switches, radio, power sunroof (if equipped), and ignition-power ed power out- lets will remain active for up to 60 minutes after the ignition switch is turned to the LOCK position. Opening either door will cancel this feature. The time for this feature is pr ogrammable. Refer to “Delay Power Off to Accessories Until Exit,?[...]

SENTR Y KEY 姞 The Sentry Key 威 Immobilizer System prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regar dless of whether the vehicle is locked or unlocked. The system uses the factory-mated Remote Keyless Entry (RKE) transmitter with integrated key and[...]

Replacement Keys NOTE: Only RKE transmitters that are pr ogrammed to the vehicle electronics can be used to start and operate the vehicle. Once a transmitter is programmed to a vehicle, it cannot be programmed to any other vehicle. CAUTION! Always remove the keys from the vehicle and lock all doors when leaving the vehicle unattended. At the time o[...]

2. Insert the second valid integrated key and turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound and the V ehicle Security Light will begin to flash. T urn the ignition switch to the LOCK position and remove the second key . 3. Insert a blank integrated key into the ignition switch and turn the ignit[...]

VEHICLE SECURITY ALARM The V ehicle Security Alarm monitors the vehicle doors for unauthorized entry and the ignition switch for unau- thorized operation. If something triggers the alarm, the V ehicle Security Alarm will pr event the vehicle from starting and provide the following audible and visible signals: the horn will pulse; the headlights wil[...]

NOTE: • The driver’s door key cylinder and the trunk button on the RKE transmitter cannot arm or disarm the V ehicle Security Alarm. • The V ehicle Security Alarm r emains armed during trunk entry . Pressing the TRUNK button will not disarm the V ehicle Security Alarm. If someone enters the vehicle through the tr unk, and opens any door , the[...]

The lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned ON from the LOCK position. NOTE: • None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extr eme downward position), unless the overhead map/r eading lights are turned on manually . [...]

T o Unlock The Doors Press and r elease the UNLOCK button on the transmitter once to unlock the driver’s door , or twice within five seconds, to unlock both doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote Key Unlock, Driver Door/All Doors First This feature lets you[...]

Flash Lights with Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the transmitter . This feature can be turned on or turned of f. Refer to “Flash Lights with Remote Key Lock,” under ⬙ Personal Settings (Customer Programmable Featur es),” under “Electronic V ehicle Informat[...]

Headlights On with Remote Key Unlock,” under “Per- sonal Settings (Customer Programmable Featur es),” un- der “Electronic V ehicle Information Center (EVIC)” in Section 4. T o Lock The Doors Press and r elease the LOCK button on the transmitter to lock both doors. The turn signal lights will flash and the horn will chirp to acknowledge th[...]

Express Down Window Feature This feature allows you to r emotely lower both door windows at the same time. T o use this feature, pr ess and release the UNLOCK button on the transmitter and then immediately press and hold the UNLOCK button until the windows lower to the level desired or until they lower completely . T o Open The T runk Press the TRU[...]

Programming Additional T ransmitters Refer to Sentry Key 威 “Customer Key Programming.” If you do not have a programmed RKE transmitter , contact your authorized dealer for details. T ransmitter Battery Service The recommended r eplacement battery is one CR2032 battery . NOTE: • Perchlorate Material — special handling may apply . See www .[...]

3. Reposition the access door panel over the battery opening and snap into place. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference r eceived, includi[...]

• Doors closed • Hood closed • Hazard switch of f • Brake switch inactive (brake pedal not pressed) • Ignition key removed fr om ignition switch • Battery at an acceptable charge level, and • RKE P ANIC button not pressed. T o Enter Remote Start Mode Press and r elease the REMOTE ST AR T button on the RKE transmitter twice, within fiv[...]

NOTE: T o avoid unintentional shut downs, the system will disable the one time press of the REMOTE ST AR T button for two seconds after receiving a valid Remote Start request. T o Exit Remote Start Mode and Drive the V ehicle Before the end of the 15-minute cycle, pr ess and release the UNLOCK button on the RKE transmitter to unlock the doors and d[...]

If the door lock plunger is down when you shut the door , the door will lock. Therefor e, make sure the key is not inside the vehicle before closing the door . W ARNING! • For personal security and safety in the event of an accident, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehic[...]

If you press the power door lock switch while the key is in the ignition, and either door is open, the power locks will not operate. This prevents you fr om accidentally locking the key in the vehicle. Removing the key or closing the door will allow the locks to operate. If a door is open, the key is in the ignition, and the ignition is in the LOCK[...]

Automatic Door Locks — If Equipped The auto door lock feature can be enabled or disabled by your authorized dealer . See your authorized dealer for programming. Automatic Unlock Doors on Exit The doors will unlock automatically if: 1. The Automatic Unlock Doors On Exit feature is en- abled 2. The transmission was in gear and the vehicle speed ret[...]

5. A single chime will indicate the completion of the programming. NOTE: If you do not hear the chime, it means that the system did not enter the programming mode and you will need to repeat the pr ocedure. 6. Repeat these steps if you want to return this featur e to its previous setting. NOTE: Use the Automatic Unlock Doors On Exit feature in acco[...]

NOTE: • The door window will lower slightly if it is closed completely when opening the door . The window will return to its fully closed position after closing the door . This action allows the door to open without resistance and prevents window and seal damage. • Y ou can remotely lower both the driver side and passenger side windows at the s[...]

Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter-type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buf feting occurs with[...]

W ith the ignition switch in the ON position, the T runk Open symbol will display in the instrument cluster indicating that the trunk is open. The odometer display will reappear once the tr unk is closed. W ith the ignition switch in the LOCK position or the key removed fr om the ignition switch, the T runk Open sym- bol will display until the trun[...]

T runk Emergency Release The trunk of your vehicle is equipped with an emer gency release handle. It is located on the inside of the tr unk lid, near the latch, and is coated so that it glows in a darkened trunk. Pull on the handle to open the trunk. OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint [...]

W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. Y ou can strike the interior of your vehicle or other passengers or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly . Buckle up even though you are an excellent driver , e[...]

W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a se[...]

2. The seat belt latch plate is contacting the seat when the belt is routed thr ough the seat web guide. When the belt is routed outside of the seat web guide, the latch plate will contact the quarter trim panel. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap[...]

W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop, you could move too far forward, increasing[...]

W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt cannot do its job as well. In a collision, it could even cut into you. Be sure the [...]

W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (ben[...]

NOTE: These devices are not a substitute for pr oper seat belt placement by the occupant. The seat belt still must be worn snug and positioned properly . The pretensioners ar e triggered by the Occupant Re- straint Controller (ORC). (Refer to information on Air- bags in this section). Like the front airbags, the pr eten- sioners are single use item[...]

NOTE: Y ou must perform the following steps within 60 seconds of turning the ignition switch to the ON position. 3. W ithin 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver’s seat belt at least three times, ending with the seat belt buckled. NOTE: W atch for the Seat Belt Reminder Light to turn [...]

3. Allow the belt to retract. As the belt retracts, you will here a clicking sound. This indicates the safety belt is now in the Automatic Locking mode. How to Disengage the Automatic Locking Mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the Automatic Locking mode and activate the vehicle sensit[...]

Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt r estraint systems. The driver side front airbag is mounted in the center of the steering wheel. The passenger side front airbag is mounted in the instrument panel, above the[...]

The front airbags have a multistage inflator design. This allows the airbag to have differ ent rates of inflation that are based on collision severity . W ARNING! • Do not put anything on or around the front airbag covers or attempt to open them. Y ou may damage the airbags and you could be injured because the airbags are no longer functional. Th[...]

W ARNING! • Do not stack luggage or other cargo up high enough to block the location of the side curtain airbag. The area where the side curtain airbag is located should remain free from any obstructions. • Do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that[...]

W ARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment could cause severe injury or death to infants in that position. 2. Children who ar e not big enough to wear the vehicle seat belt properly should be secur ed in the rear seat in child restraints or b[...]

W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag dep[...]

• Interconnecting W iring • Seat Belt Reminder Light • Knee Impact Bolsters • Front Acceleration Sensors • Driver and Front Passenger Seat Belt Pr etensioners How the Airbag System W orks • The Occupant Restraint Controller (ORC) determines if a frontal collision is sever e enough to requir e the airbags to inflate. The front airbag inf[...]

W ARNING! Ignoring the AIRBAG W arning Light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away . • The Driver and Front Passenger Airbag/Inflator Units are l[...]

inflating side curtain airbag pushes the outside edge of the headliner out of the way and covers the window . The airbag inflates in about 30 milliseconds (about one-quarter of the time that it takes to blink your eyes) with enough force to injur e you if you are not belted and seated properly , or if items are positioned in the area wher e the sid[...]

irritation, move to fresh air . If the irritation continues, see your doctor . If these particles settle on your clothing, follow the garment manufacturer’s instr uc- tions for cleaning. • It is not advisable to drive your vehicle after the airbags have been deployed. If you are involved in another collision, the airbags will not be in place to[...]

Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper passen[...]

Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to recor d up to five seconds of specific vehicle data param- eters (see the following list) in an event data recor der prior to the moment of airbag deployment, or near deployment, and up to a quarter second of high-speed deceleration data during and/or after airbag de[...]

upon request. General data that does not identify par - ticular vehicles or crashes may be released for incorpo- ration in aggregate crash databases, such as those main- tained by the U.S. government and various states. Data of a potentially sensitive nature, such as would identify a particular driver , vehicle, or crash, will be treated confi- den[...]

• Cruise contr ol status • T raction/stability control status • T ire Pressur e Monitoring System status (if equipped) Child Restraint Everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the United States and all Canadian provinces r equire that small children ride in pr oper restraint s[...]

Infants and Child Restraints • Safety experts recommend that childr en ride rearwar d-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). T wo types of child restraints can be used r earward-facing, infant carriers and convertible child seats. • The infant carrier is only used rearwar d-facing in the veh[...]

The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who ar e still too small to fit the vehicle’s seat belts properly . If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, they should use a belt-positioning booster seat. The child and belt[...]

W ARNING! (Continued) • A rearward-facing child restraint should only be used in a rear seat. A rearward-facing child re- straint in the front seat may be struck by a deploy- ing passenger airbag, which may cause severe or fatal injury to the infant. Here are some tips on getting the most out of your child restraint: • Before buying any r estra[...]

the child restraint using lower anchorages and upper tether straps from the child r estraint to the vehicle structur e. LA TCH-compatible child restraint systems ar e now avail- able. However , because the lower anchorages are to be introduced over a period of years, child r estraint systems having attachments for those anchorages will continue to [...]

Installing the LA TCH-Compatible Child Restraint System W e urge you to follow the manufactur er’s directions carefully when installing your child r estraint. Not all child restraint systems will be installed as described her e. Again, carefully follow the installation instr uctions that are pr ovided with the child restraint system. The rear sea[...]

most direct path between the anchor and the child restraint. Finally , tighten all three straps as you push the child restraint r earward and downwar d into the seat, removing slack in the straps accor ding to the child restraint manufactur er’s instructions. NOTE: • Ensure that the tether strap does not slip into the opening between the seatba[...]

restraint so that it is not necessary to use a locking clip. Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight; however , any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary . The seat belt must be in the Automati[...]

2. Route the tether strap to provide the most dir ect path for the strap between the anchor and the child seat. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child r estraint manufacturer’s instruc- tions. NOTE: Ensure that the tether strap does not slip into the[...]

ENGINE BREAK-IN RECOMMENDA TIONS A long break-in period is not requir ed for the drivetrain (engine, transmission, and rear axle) in your new vehicle. Drive moderately during the first 500 mi (800 km). After the initial 60 mi (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-thr ottle acceleration within [...]

SAFETY TIPS T ransporting Passengers NEVER TRANSPOR T P ASSENGERS IN THE CARGO AREA. W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is no[...]

If you are r equired to drive with the trunk/liftgate open, make sure that all windows ar e closed and the climate control BLOWER switch is set at high speed. DO NOT use the recir culation mode. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the[...]

Defroster Check operation by selecting the defrost mode and place the blower control on high speed. Y ou should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Periodic Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for excessive tr ead wear a[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors ............................. 7 5 ▫ Automatic Dimming Inside Mirror — If Equipped ....................... 7 5 ▫ Outside Mirrors ..................... 7 6 ▫ Outside Mirrors Folding Featur e ......... 7 6 ▫ Power Mirrors ...................... 7 6 ▫ Heated Mirrors — If Eq[...]

䡵 V oice Recognition System (VR) — If Equipped ........................ 1 0 7 ▫ V oice Recognition System (VR) Operation . . 107 ▫ Commands ....................... 1 0 9 ▫ V oice T raining ..................... 1 1 2 䡵 Seats ............................. 1 1 2 ▫ Easy Entry Seats .................... 1 1 2 ▫ Power Seats .............[...]

䡵 W indshield W ipers And W ashers ......... 1 2 6 ▫ Intermittent W iper System ............. 1 2 7 ▫ Mist Feature ....................... 1 2 7 ▫ W indshield W ashers ................. 1 2 7 ▫ Headlights On W ith W ipers (A vailable W ith Auto Headlights Only) ................ 1 2 8 䡵 T ilt/T elescoping Steering Column ......... 1 2 8 [...]

䡵 Power Sunroof — If Equipped ........... 1 4 0 ▫ Opening Sunroof - Partially ............ 1 4 1 ▫ Opening Sunroof - Expr ess ............ 1 4 1 ▫ Closing Sunroof - Partially ............ 1 4 1 ▫ Closing Sunroof - Expr ess ............. 1 4 2 ▫ Pinch Protect Featur e ................ 1 4 2 ▫ Pinch Protect Override ............... 1 [...]

MIRRORS Automatic Dimming Inside Mirror — If Equipped This mirror automatically adjusts for headlight glar e from vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light next to the button will illuminate to indicate when the dimming feature is activated. CAUTION! T o avoid damage to th[...]

Outside Mirrors T o receive maximum benefit, adjust the outside mirr or(s) to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirr or . NOTE: The passenger-side convex outside mirr or will give a much wider view to the rear , and especially of the lane next to your vehicle. W ARNING! V ehicles and ot[...]

After selecting a mirror , move the knob in the same direction you want the mirr or to move. Use the center off position to guard against accidentally moving a mirr or position. Heated Mirrors — If Equipped These mirrors ar e heated to melt frost or ice. This feature is activated whenever you turn on the r ear window defroster . Refer to “Rear [...]

Slide On Rod and Extender Features of Sun Visor T o use the slide on rod featur e of the sun visor , rotate the sun visor downward and swing the sun visor so it is parallel to the side window , grabbing the sun visor with your left hand pull rearwar ds until the sun visor is in the desired position. T o use the extender feature of the sun visor , g[...]

uconnect 姞 phone — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated uconnect 威 phone. Refer to your “Navigation User’s Manual” for uconnect 威 phone operating instruc- tions for these radios. Radio sales code can be located on the lower right corner of the Radio faceplate. uconnect 威 phone is a voice-activate[...]

it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s uconnect 威 phone. The uconnect 威 phone allows up to seven cellular phones to be linked to the system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or Fr[...]

Operation V oice commands can be used to operate the uconnect 威 phone and to navigate through the uconnect 威 phone menu structur e. V oice commands are r equired after most uconnect 威 phone prompts. Y ou will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait fo[...]

Cancel Command At any prompt, after the beep, you can say ⬙ Cancel ⬙ and you will be returned to the main menu. However , in a few instances the system will take you back to the previous menu. Pair (Link) uconnect 威 phone to a Cellular Phone T o begin using your uconnect 威 phone, you must pair your compatible Bluetooth 威 enabled cellular [...]

phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority three and priority five phones are pr esent in the vehicle, the uconnect 威 phone will use the priority three cellular phone when you make a call. Y ou can select to use a lower priority cellular phone at any time (refer to ⬙ Advanced Phone Con[...]

• The uconnect 威 system will confirm the name and then dial the corresponding phone number , which may appear in the display of certain radios. Add Names to Y our uconnect 威 Phonebook NOTE: Adding names to the uconnect 威 phonebook is recommended when the vehicle is not in motion. • Press the PHONE button to begin. • After the ⬙ Ready [...]

Phonebook Download – Automatic Phonebook T ransfer From Cellular Phone If equipped and specifically supported by your phone, uconnect 威 phone automatically downloads names (text names) and number entries from the cellular phone’s phonebook. Specific Bluetooth 威 Phones with Phone Book Access Profile may support this featur e. See uconnect ?[...]

Phonebook Download — Single Entry If equipped and supported by your phone, uconnect 威 phone allows the user to download entries from their phone via Bluetooth 威 . T o use this feature, pr ess the PHONE button and say “Phonebook Download.” The system prompts, “Ready to accept “V” car d entry via Bluetooth 威 …” The system is now[...]

• Y ou will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, cellular , or pager) that you wish to edit. • When prompted, r ecite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be gi[...]

• After you enter the name, the uconnect 威 phone will ask you which designation you wish to delete: home, work, cellular , pager , or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. • Automatic downloaded phonebook entries cannot be deleted or edited. Delete/Erase “All?[...]

• The uconnect 威 phone will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed thr ough the uconnect 威 phone if the feature(s) ar e available on your cellular service plan. For example, if your cellular service plan provides thr ee-w[...]

refer to ⬙ T oggling Between Calls ⬙ in this section. T o combine two calls, refer to ⬙ Confer ence Call ⬙ in this section. Place/Retrieve a Call From Hold T o put a call on hold, press the PHONE button until you hear a single beep. This indicates that the call is on hold. T o bring the call back from hold, pr ess and hold the PHONE button [...]

• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Redial. ⬙ • The uconnect 威 phone will call the last number that was dialed from your cellular phone. NOTE: This may not be the last number dialed from the uconnect 威 phone. Call Continuation Call continuation is the progr ession of a phone call on the uconnect 威 phone afte[...]

• Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every uconnect 威 phone language change operation, only the language-specific 32-name phone- book is usable. The paired phone name is not language- specific and usa[...]

• The uconnect 威 phone does slightly lower your chances of successfully making a phone call as to that for the cell phone directly . W ARNING! Y our phone must be turned on and paired to the uconnect 威 phone to allow use of this vehicle feature in emergency situations, when the cell phone has network coverage and stays paired to the uconnect [...]

W orking with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. Y ou can use your uconnect 威 phone to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some s[...]

Barge In - Overriding Prompts The “V oice Recognition” button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately . For example, if a prompt is asking ⬙ W ould you like to pair a phone, clear a..., ⬙ you could press the VOICE RECOGNITION button and say , ⬙ Pair a Phone ⬙ to select that[...]

NOTE: Certain brands of cellular phones do not send the dial ring to the uconnect 威 phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progr ess. Once your call is answered, you will hear the [...]

If you would like to connect or disconnect the Bluetooth 威 connection between a uconnect 威 phone paired cellular phone and the uconnect 威 phone, follow the instructions described in your cellular phone User’s Manual. List Paired Cellular Phone Names • Press the PHONE button to begin. • After the “Ready” prompt and the following beep[...]

Delete uconnect 威 phone Paired Cellular Phones • Press the PHONE button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing. ⬙ • At the next prompt, say ⬙ Delete ⬙ and follow the prompts. • Y ou can also press the VOICE RECOGNITION button at any time while the list is being played, and then[...]

This procedur e may be repeated with a new user . The system will adapt to the last trained voice only . T o restor e the V oice Recognition system to factory default settings, enter the V oice T raining session via the above procedur e and follow the prompts. V oice Recognition (VR) • For best performance, adjust the rearview mirr or to provide [...]

• It is not recommended to stor e similar sounding names in the uconnect 威 phonebook. • Phonebook (Downloaded and uconnect 威 phone Local) name recognition rate is optimized when the entries are not similar . • Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero). ⬙ 800 ⬙ must be spoken ⬙ eight-zero-zer o. ⬙ • Even tho[...]

Bluetooth 威 Communication Link Cellular phones have been found to lose connection to the uconnect 威 phone. When this happens, the connection can generally be reestablished by switching the phone off/on. Y our cellular phone is recommended to r emain in Bluetooth 威 ON mode. Power-Up After switching the ignition key from OFF to either the ON or[...]

102 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 103 3[...]

104 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 105 3[...]

V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistan[...]

General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly appr oved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interf[...]

When you press the VR button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR button, listen for the beep, and say your command. Pressing the VR bu[...]

Commands The V oice Recognition system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the V olume 1. Start a dialogue by pressing the VR button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volum[...]

Radio FM T o switch to the FM band say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency” (to change the fr equency) • “Next Station” (to select the next station) • “Previous Station” (to select the pr evious station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (t[...]

Memo T o switch to the voice recor der mode say “Memo”. In this mode, you may say the following commands: • “New Memo” (to recor d a new memo) — During the recor ding you may press the VR button to stop r ecord- ing. Y ou proceed by saying one of the following commands: − “Save” (to save the memo) − “Continue” (to continue r[...]

NOTE: Keep in mind that you have to press the VR button first and wait for the beep before speaking the “Barge In” commands. V oice T raining For users experiencing difficulty with the system r ecog- nizing their voice commands or numbers, uconnect 威 phone V oice T raining feature may be used. 1. Press the VR button, say “System Setup” an[...]

Power Seats The power seat switches are on the outboar d side of the front seat cushions. The power seat switch can be moved forward and backwar d as well as up and down to control the position of the seat. The power seatback switch is used to adjust the angle of the seatback. Push forward or rearwar d on the switch to change the position of the se[...]

W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. CAUTION! Do not place any article under a power seat as it may cause damage to the seat control[...]

Lumbar Support This feature allows you to incr ease or decrease the amount of lumbar support. T urn the control lever for - ward to incr ease and rearwar d to decrease the desired amount of lumbar support. Head Restraints Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear . Adjust the restraint so that the[...]

Heated Seats The driver seat and front passenger seat ar e heated. The heaters provide the same heat level for both cushion and seatback. The controls for each heater ar e located near the bottom center of the instrument panel. After turning on the ignition, you can choose from High, Low , or Off heat settings. Amber indicators in the top portion o[...]

If high level heating is selected, the system will automati- cally switch to the low level after 30 minutes of continu- ous operation. At that time, the number of indicators illuminated changes from two to one, indicating the change. Operation on the low setting also turns off automatically after 30 minutes. NOTE: Once a heat setting is selected, h[...]

When the seatback is folded to the upright position, make sure it is latched by str ongly pulling on the top of the seatback above the seat strap. W ARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or pa[...]

TO OPEN AND CLOSE THE HOOD T wo latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. 2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. Hood Release Lever Hood Safety Catch UNDERST [...]

CAUTION! T o prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. W ARNING! If the hood is not fully latched, it could fly up when the vehicle is [...]

Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. T urn it to the second detent for headlight, parking light and instrument panel light operation. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. T o turn t[...]

position. In addition, the headlights will turn off when the wipers are turned of f if they were turned on by this feature. The Headlights On with W ipers feature can be enabled or disabled. Refer to ”Headlights On with W ipers,” under “Personal Settings (Customer-Pr ogrammable Features)” under “Electronic V ehicle Information Center (EVI[...]

Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF , a chime will sound to alert the driver when the driver’s door is opened. Fog Lights — If Equipped The front fog light switch is built into the head- light switch. T o activate the front fog lights, turn on the parking lights or the low beam headligh[...]

T urn Signals Move the multifunction lever up or down and the corresponding turn signal indicator in the instr ument cluster flashes to show proper operation of the fr ont and rear turn signal lights. Y ou can also signal a lane change by moving the multifunction lever partially up or down without moving beyond the detent. Releasing the multi- func[...]

Interior Lights The interior lights come on when a door is opened. T o protect the battery , the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or ar e on because a door is open. This includes the glove box light, but no[...]

Dome Light Position Rotate the dimmer control completely upwar d to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer contr ol is in this position. Interior Light Defeat (OFF) Rotate the dimmer control to the extr eme bottom off position. The interior lights will remain of f when the doors are open[...]

CAUTION! T urn the windshield wipers off when driving through an automatic car wash. Damage to the wind- shield wipers may result if the wiper switch is left in any position other than off. Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause be- tween cycles desirable. Rotate[...]

If you activate the washer while the windshield wiper control is in the delay range, the wipers will operate for two wipe cycles after releasing the multifunction lever and then resume the intermittent interval pr eviously selected. If you activate the washer while the windshield wiper is turned off, the wipers will operate for thr ee wipe cycles a[...]

T o unlock the steering column, pull the control handle outward. T o tilt the steering column, move the steering wheel upward or downwar d as desired. T o lengthen or shorten the steering column, pull the steering wheel outward or push it inwar d as desired. T o lock the steering column in position, push the control handle inwar d until fully engag[...]

T o Activate Push and release the ON/OFF button located on the end of the Electronic Speed Contr ol lever . The indicator light in the instrument cluster will illuminate to show that the speed control system is on. T o turn the system off, push and release the ON/OFF button again. The system and the indicator light will turn off. W ARNING! Leaving [...]

T o Set At A Desired Speed When the vehicle reaches the speed desir ed, push the lever downward to SET DECEL and release. Remove your foot from the accelerator pedal and the vehicle will operate at the selected speed. NOTE: • Electronic Speed Contr ol will only function in 3rd, 4th, or 5th gear when in the Autostick 威 mode (if equipped). • El[...]

T apping the lever to RESUME ACCEL once will r esult in a 1 mph (1.6 km/h) speed increase. Each time the lever is tapped speed increases, so tapping the lever thr ee times will increase speed by 3 mph (4.8 km/h), etc. T o decrease speed while Electr onic Speed Control is set, push down and hold the lever in SET DECEL. Release the lever when the des[...]

W ARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Y our ve- hicle could go too fast for the conditions and you could lose control. An accident could be the result. Don’t use Electronic Speed Control in heavy traffic or on roads that are winding, icy , snow-covered, or slippery . OVERHEAD CONSOL[...]

These lights also turn on when a door is opened, or when the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed, or when the dimmer contr ol is turned fully upward, past the second detent. Sunglasses Storage At the rear of the console, a compartment is pr ovided for the storage of a pair of sunglasses. The storage compartment ac[...]

W ARNING! • Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes [...]

2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink 威 buttons while keeping the EVIC display in view . For optimal training, point the battery end of the hand- held transmitter away from the HomeLink 威 . 3. Simultaneously , press and hold both the chosen HomeLink 威 button and the hand-held transmitter button until the E[...]

This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly press and r elease the “learn” or “training” button. The name and color of the button may vary by manufacturer . NOTE: There ar e 30 seconds in which to initiate the [...]

Gate Operator/Canadian Programming Canadian radio-frequency laws r equire transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink 威 to pick up the signal during programming. Similar to this Canadian law , some U.S. gate operators are designed to “time-out” in the sa[...]

Reprogramming A Single HomeLink 姞 Button T o repr ogram a channel that has been previously trained, follow these steps: 1. T urn the ignition switch to the ON/RUN position. 2. Press and hold the desir ed HomeLink 威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. W ithout releasing the [...]

General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference that may be received including interfer ence that may cause undesired operation NOTE: The transmitter has bee[...]

W ARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with[...]

the switch in the forward position, the sunr oof will close fully and then stop automatically . Release the switch once the sunroof stops moving. Closing Sunroof - Express Press the switch forwar d and release, and the sunr oof will close automatically from any position. The sunr oof will close fully and stop automatically . This is called Express [...]

NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter-type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occu[...]

The center console outlet is powered dir ectly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or pr event engine starting. W ARNING! T o avoid serious injury or death: • Do not use a three-prong adapter . • Do not insert any objects into the receptacles. • Do not touch with wet ha[...]

CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery even when not in use (i.e., cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, va[...]

CUPHOLDERS Front Cupholders The front cupholders ar e located in the center console. Illuminated Front Cupholders — If Equipped The front cupholders ar e illuminated with LEDs. They are turned on with the headlights or parking lights. Refer to “Interior Lights” under “Lights” in Section 3. Rear Cupholders The rear seat cupholders ar e loc[...]

CONSOLE FEA TURES Sliding Center Console Armrest The center console armrest slides forwar d with three detents to provide flexibility for comfort, cupholder use, and shifting ease. Rear Cupholders Sliding Console Armrest UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 147 3[...]

Console Storage The center console has a storage compartment located underneath the armrest, and also contains a 12-V olt power outlet, a molded-in coin holder (designed to hold various size coins). The center console may also be equipped with a Universal Consumer Interface (UCI). UCI supports Mini, 4G, Photo, Nano, 5G iPod 威 and iPhone 威 devic[...]

REAR WINDOW FEA TURES Rear Window Defroster The pushbutton for the rear window defr oster is located on the mode knob of the climate control switch bank. Press this button to turn on the r ear window defroster and the electric r emote control heated mirr ors (if equipped). An amber light shows that the defroster is on. The defroster will automatica[...]

[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Featur es .............. 1 5 5 䡵 Instrument Cluster – Base .............. 1 5 6 䡵 Instrument Cluster – Pr emium ........... 1 5 7 䡵 Instrument Cluster Description ........... 1 5 8 䡵 Electronic V ehicle Information Center (EVIC) . 169 ▫ Electronic V ehicle Information[...]

䡵 Sales Code REQ — AM/FM Ster eo Radio And 6–Disc CD Changer (MP3/WMA AUX Jack) . . . 182 ▫ Operating Instructions - Radio Mode ..... 1 8 2 ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play) ............ 1 8 7 ▫ Notes On Playing MP3/WMA Files ...... 1 8 9 ▫ List Button (Disc Mode For MP3/WMA Play) ...................[...]

▫ Operation Instructions — CD Mode For CD And MP3 Audio Play ................. 2 1 1 ▫ Notes On Playing MP3 Files ........... 2 1 3 ▫ List Button (CD Mode For MP3 Play) ..... 2 1 6 ▫ Info Button (CD Mode For MP3 Play) .... 2 1 6 䡵 Universal Consumer Interface (UCI) — If Equipped ........................ 2 1 7 ▫ Connecting The iPod ?[...]

䡵 Kicker 威 High Performance Sound System W ith Driver-Selectable Surr ound (DSS) – If Equipped ......................... 2 2 7 䡵 Remote Sound System Controls .......... 2 2 8 䡵 CD/DVD Disc Maintenance ............. 2 2 9 䡵 Radio Operation And Cellular Phones ...... 2 3 0 䡵 Climate Controls ..................... 2 3 0 ▫ Manual Air Co[...]

INSTRUMENT P ANEL FEA TURES 1 - Air Outlets 5 - Heated Seat Switch 9 - Ignition Switch 2 - Instrument Cluster 6 - ESP OFF Switch 10 - T runk Release Switch 3 - Glove Compartment 7 - Hazard W arning Switch 1 1 - Headlight Switch 4 - Radio 8 - Climate Control UNDERST ANDING YOUR INSTRUMENT P ANEL 155 4[...]

INSTRUMENT CLUSTER – BASE 156 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

INSTRUMENT CLUSTER – PREMIUM UNDERST ANDING YOUR INSTRUMENT P ANEL 157 4[...]

INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. T rip Odometer Button Press this button to change the display fr om odometer to either of two trip odometer settings. The letter “A” or “B” will appear when in the trip odometer mode. Push in a[...]

7. Electronic Thr ottle Control (ETC) W arning Light This light will turn on briefly as a bulb check when the ignition switch is turned ON. This light will also turn on while the engine is running if ther e is a problem with the Elec- tronic Thr ottle Control (ETC) system. If the light comes on while the engine is running, safely bring the vehicle [...]

CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H,” and you hear a chime, turn the engine OFF immediately and[...]

1 1. Engine T emperature W arning Light This light will turn on and a single chime will sound to warn of an overheated engine condition. When this light turns on, the engine temperature is critically hot. If the light turns on while driving, safely pull over and stop the vehicle. The vehicle should be turned OFF immediately and serviced as soon as [...]

14. Oil Pressur e W arning Light This light indicates low engine oil pressur e. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause i[...]

19. Odometer/Electronic V ehicle Information Center (EVIC) Display The odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “T rip Odometer Button” for additional information. NOTE: U.S. Federal regulations r equire upon transfer of vehicle ownership, the seller certify the mil[...]

the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON position. T o turn off the message temporarily ,[...]

the brake booster , the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a r eserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake W arning Light, which will t[...]

The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 21. V ehicle Security Light — If Equipped This light will flash at a fast rate for approxi- mately 15 seconds, when the vehicle [...]

maintain correct tir e pressur e, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pr essure telltale. Y our vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly . The TPMS malfunction indicator is combined with the low tire pr essure tel[...]

23. Anti-Lock Brake (ABS) Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is requir[...]

26. Door Ajar Indicator This light will turn on to indicate that one or more door may be ajar . 27. Decklid Ajar Indicator This light will turn on to indicate that the decklid may be ajar . 28. W indshield W asher Fluid Low Indicator This light will turn on to indicate the windshield washer fluid is low . ELECTRONIC VEHICLE INFORMA TION CENTER (EVI[...]

• V ehicle Information W arning Message Displays • T ire Pressur e Monitor System • Personal Settings (Customer Programmable Featur es) • Compass Display • Outside T emperature Display • T rip Computer Functions • uconnect 威 phone (If Equipped) • uconnect 威 gps Screens (If Equipped) • Audio Mode Display • Surround Sound Mode[...]

Features). The SCROLL button also functions as a remote sound system control. Refer to “Remote Sound System Controls” in this section. AUDIO MODE Button Press the AUDIO MODE button to select the Compass/T emp/Audio screen. Along with compass reading and outside temperatur e, this screen will display radio and media mode information depending on[...]

• Channel # T rained • Clearing Channels • Channels Cleared • Did Not T rain • Left Front Low Pr essure (with a single chime) • Left Rear Low Pressur e (with a single chime) • Right Front Low Pr essure (with a single chime) • Right Rear Low Pressur e (with a single chime) • Check TPM System (with a single chime) • ESP Of f – E[...]

indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. T o turn off the message temporarily , press and release the MENU button. T o reset the oil cha[...]

“RESET” or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel average r eading before the reset. • Distance T o Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted averag[...]

T o Reset The Display Reset will only occur while a resettable function is being displayed. Press and r elease the FUNCTION SELECT button once to clear the resettable function being dis- played. T o reset all r esettable functions, press and release the FUNCTION SELECT button a second time within three seconds of r esetting the currently-displayed [...]

NOTE: Under certain conditions, the display may be superseded by another display of higher priority . But when the ignition switch position is changed, the display always re-appears. Compass Display COMP ASS Button The compass readings indicate the dir ection the vehicle is facing. Press and r elease the COMP ASS button to display one of eight com-[...]

5. Complete one or more 360 degr ee turns (in an area fr ee from lar ge metal or metallic objects) until the “CAL” message turns off. The compass will now function normally . Compass V ariance Compass V ariance is the differ ence between magnetic North and geographic North. In some areas of the country , the difference between magnetic and geog[...]

3. Press the SCROLL button until “Compass V ariance” message and the last variance zone number displays in the EVIC. 4. Press and r elease FUNCTION SELECT button until the proper variance zone is selected accor ding to the map. 5. Press and r elease the COMP ASS button to exit. Driver-Selectable Surround Sound (DSS) – If Equipped Press and r [...]

Press and r elease the MENU button until Personal Set- tings displays in the EVIC. Use the SCROLL button to display one of the following choices. Language When in this display you may select one of three lan- guages for all display nomenclature, including the trip functions and the uconnect 威 gps (if equipped). Press the FUNCTION SELECT button wh[...]

the doors will unlock on the first press of the RKE transmitter UNLOCK button. T o make your selection, press and r elease the FUNCTION SELECT button until “Driver Door 1st Press” or “All Doors 1st Pr ess” appears. Sound Horn with Remote Key Lock When ON is selected, a short horn sound will occur when the RKE transmitter LOCK button is pres[...]

Hill Start Assist (HSA) — If Equipped When on is selected, the HSA system is active. Refer to “HSA (Hill Start Assistance)” under “Electronic Brake Control System” in Section 5 of this manual for system function and operating information. T o make your selec- tion, press and r elease the FUNCTION SELECT button until “ON” or “OFF” [...]

SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control [...]

to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to sear ch for the next listenable station in AM, FM or Satellite (if equipped) frequenc[...]

4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL contr ol knob to save the time change. 5. T o exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button and selecting the “SET HOME CLOCK” entry . Once in this display follow the above procedur e, starting a[...]

SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary TUNE/SCROLL control knob a fifth time and F ADE will display . T urn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and r ear speakers. Push the rotary TUNE/SCROLL control knob again[...]

Program T ype 16-Digit Character Dis- play Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R & B Sports Sports T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when the Music T ype icon is displayed, the radio will be tuned t[...]

Y ou may add a second station to each pushbutton by repeating the above pr ocedure with this exception: Pr ess the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM, 12 FM, and 12 Satellite (if equipped) stations to be stored into pushbutton memory[...]

CAUTION! This CD player will accept 4–3/4 in (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) wher e the CD was loaded and the disc will unload and move to the entrance for easy removal. Radi[...]

R W/FF (CD MODE) Press and hold FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased, or R W or another CD button is pressed. The R W (Rewind) button works in a similar manner . AM or FM Button (CD MODE) Switches the radio to the radio mode. Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however , [...]

Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files). Discs created with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for CD audio or MP3/ WMA playback may result [...]

ID3 T ag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pr o files are not supported. Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contai[...]

INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button r epeatedly will scroll thr ough the following T AG information: Song T itle, Artist, File Name, and Folder Name (if available). Press the INFO button once mor e to return to ⬙ elapsed time ⬙ priority mode. Press and hold the INFO button for thr ee seconds or more and radio will [...]

TIME Button (Auxiliary Mode) Press the TIME button to change the display fr om elapsed playing time to time of day . The time of day will display for five seconds. R W/FF (Auxiliary Mode) No function. SET Button (Auxiliary Mode) No function. Operating Instructions — V oice Recognition System (VR) (If Equipped) For the radio, refer to “V oice Re[...]

DTS™ ⬙ DTS™ ⬙ and ⬙ DTS™ 2.0 ⬙ are trademarks of Digital The- ater Systems, Inc. AM/FM/CD/DVD RADIO (RER/REN) – IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The REN and RER radios contain a CD/DVD player , USB port, and a 30-gigabyte hard drive (HDD). Sirius Satellite Radio is option[...]

T o Manually Set the Clock — RER/REN 1. T urn on the radio. 2. T ouch the screen wher e the time is displayed. 3. T ouch the screen wher e “User Clock” is displayed. The clock setting menu will appear on the screen. 4. T o move the hour forward, touch the scr een where the word “Hour” with the arr ow pointing upward is dis- played. T o mo[...]

Show T ime if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned of f. Proceed as follows to change the current setting: 1. T urn on the radio. 2. T ouch the screen wher e the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark [...]

SALES CODE RES — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to tu[...]

to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button Press the TIME button to alternate locations of the time and frequency display . Clock Setting Procedure 1. Press and hold the TI[...]

Push the rotary TUNE/SCROLL control knob a second time and MID will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the trebl[...]

SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory . The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corr esponding button number will display . Button s1-6 These buttons tune the radio to the stations that you commi[...]

If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number , and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only . The use of o[...]

TIME Button Press this button to change the display fr om a large CD playing time display to a small CD playing time display . R W/FF Press and hold the FF (Fast Forwar d) button and the CD player will begin to fast forward until FF is r eleased, or R W or another CD button is pressed. The R W (Reverse) button works in a similar manner . AM/FM Butt[...]

The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name, and will assign a numb[...]

rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rate. MPEG Specifi- cation Sampling Fre- quency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 8[...]

Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player , or cassette player , and utilize the vehicle’s audio system to amplify the source and play thr ough the vehicle speakers. Pressing the DISC/AUX button will change the mode to auxiliar[...]

Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic V olume Control The electronic volume contr ol turns conti[...]

If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped W ith uconnect” message will display on the radio screen. TIME Button Press the TIME button to alternate locations of the time and frequency display . Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust t[...]

TUNE Control T urn the rotary TUNE/SCROLL control knob clockwise to increase or counter clockwise to decrease the fr equency . Setting the T one, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display . T urn the TUNE/SCROLL control knob to the right or left to increase or decr ease the bass tones. Push the rotary TUNE/SCR[...]

Program T ype 16-Digit Character Dis- play No program type or un- defined None Adult Hits Adlt Hit Classical Classicl Classic Rock Cls Rock College College Country Country Foreign Language Language Information Inform Jazz Jazz News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Program T ype 16-Digit Character Dis- play Rh[...]

station with the same selected Music T ype name. The Music T ype function only operates when in the FM mode. If a preset button is activated while in the Music T ype (Program T ype) mode, the Music T ype mode will be exited and the radio will tune to the preset station. SETUP Button Pressing the SETUP button allows you to select between the followi[...]

Every time a preset button is used, a corr esponding button number will display . Button s1-6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations). DISC/AUX Button Pressing the DISC/AUX button will allow you to switch from AM/FM modes to DISC/AUX mode. Operation Instructions — CD MODE for CD[...]

CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player . Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (on[...]

R W/FF Press and hold FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased or R W or another CD button is pressed. The R W (Reverse) button works in a similar manner . AM/FM Button Press the button to select either AM or FM mode. SET/RND Button (Random Play Button) Press this button while the CD is playing to activa[...]

• Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. W ith a maximum number of files, exceeding 20 folders will result in this display [...]

MPEG Specifi- cation Sampling Fre- quency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 T ag information for artist, song title, and album title are supported for version 1 ID3 ta[...]

LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection[...]

TIME Button (Auxiliary Mode) Press this button to change the display to time of day . The time of day will display for five seconds (when the ignition is OFF). Operating Instructions - uconnect 威 phone (If Equipped) Refer to “uconnect 威 phone” in Section 3. Operating Instructions - uconnect 威 studios (Satellite Radio) (If Equipped) Refer [...]

Connecting The iPod 姞 Use the optional connection cable to connect an iPod 威 to the vehicle’s 16–pin connector port located on the center console. Once the iPod 威 is connected and synchronized to the vehicle’s UCI system (iPod 威 may take a few seconds to connect), the iPod 威 starts charging and is ready for use by pr essing radio sw[...]

Play Mode When switched to UCI mode, the iPod 威 automatically starts Play mode. In Play mode, you may use the following buttons on the radio faceplate to control the iPod 威 and display data: • Use the TUNE control knob to select the next or previous track. • T urning it clockwise (forward) by one click, while playing a track, skips to the n[...]

• While a track is playing, press the INFO button to see the associated metadata (Artist, track title, album, etc.) for that track. Pressing the INFO button again jumps to the next screen of data for that track. Once you have seen all screens, the last INFO button pr ess will take you back to the play mode screen on the radio. • Pressing the RE[...]

• During all List modes, the iPod 威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list just turn the wheel backwards (counter-clockwise) to get to the track faster . • In List mode, the radio PRESET Buttons are used as shortcuts to the following lists on the iPod 威 . • Preset 1 – Playlists • Pre[...]

CAUTION! • Leaving the iPod 威 (or any supported device) any- where in the vehicle in extreme heat or cold can alter the operation, or damage the device. Follow the device manufacturer ’ s guidelines. • Placing items on the iPod 威 , or connections to the iPod 威 in the vehicle, can cause damage to the device and/or to the connectors. W AR[...]

number 888-539-7474, or visit the Sirius web site at www .sirius.com, or at www .siriuscanada.ca for Cana- dian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Y our V ehicle Identificat[...]

bikes should be placed as far rearwar d as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interr upted due to one of the following reasons: • The vehicle is parked in an undergr ound parking structur e or under a physical obstacle. • Dense tree c[...]

INFO Button Pressing the INFO button will cycle the display informa- tion between Artist, Song T itle, and Composer (if avail- able). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song T itle all of the time (press and hold again to return to normal display). R W/FF Pressing the R W (Rewi[...]

• Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number . This number is used to activate, deactivate, or change the Sirius subscription. SET Button – T o Set the Pushbutton Memory When you are r eceiving a channel that you wish to commit to pushbutton memory , press the SET button. The symbol SET 1 will no[...]

KICKER 姞 HIGH PERFORMANCE SOUND SYSTEM WITH DRIVER-SELECT ABLE SURROUND (DSS) – IF EQUIPPED Y our vehicle is equipped with a state of the art audio amplifier that provides 5.1-channel surr ound sound from any stereo audio sour ce. A new feature of the Kicker 威 audio system offers the ability to choose surr ound sound for any audio source. “[...]

When in “Audio Surround” mode, balance is set auto- matically . Fader control is available to add more sur - round audio if desir ed. REMOTE SOUND SYSTEM CONTROLS The remote sound system contr ols are located on the surface of the steering wheel at the three and nine o’clock positions. V ehicles equipped with steering wheel-mounted buttons ar[...]

If the Compass/T emp/Audio screen is alr eady displayed when the AUDIO MODE button is pressed, then the mode will change (i.e., from AM to FM, to Media mode, etc., depending on which radio is in the vehicle). FUNCTION SELECT Button When the EVIC is in the Compass/T emp/ Audio screen, pr ess the FUNCTION SELECT button to operate various radio, media[...]

NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.e. scratched, reflective coating removed, a hair , moisture or dew on the disc) oversized, or have copyright encoding. T ry a known good disc before considering disc player service. RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phon[...]

Blower Control Use this control to r egulate the amount of air forced thr ough the ven- tilation system in any mode. The blower speed increases as you move the control to the right fr om the “O” (Off) position. Ther e are four blower speeds. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Star[...]

Mode Control Use this control to choose fr om several patterns of air distribution. Y ou can select either a primary mode as iden- tified by the symbols on the control, or a blend of two of these modes. • Panel Air is directed thr ough the outlets in the instrument panel and the center console. These outlets can be adjusted to direct airflow . NO[...]

• Mix Air is directed thr ough the floor , defrost, and side window demist outlets. This setting works best in cold or snowy conditions that requir e extra heat to the windshield. This setting is good for maintaining comfort while reducing moistur e on the windshield. • Defrost Air is directed thr ough the windshield and side window demist outl[...]

• The A/C will engage automatically to prevent fogging when the recir culation button is pressed. • The A/C can be deselected manually without disturb- ing the mode control selection. Air Conditioning Control Use this button to engage the Air Conditioning. A light will illuminate when the Air Conditioning System is engaged. NOTE: The air condit[...]

If Outside Ambient T emperature Is Mode Overrides T o T emperature Overrides T o Rear Window Defroster Active Less than 40°F Mix Full Heat Y es Between 40°F and 80°F No Override No Override No More than 80°F Bi-Level Full Cool No NOTE: • The feature can be disable by parking the vehicle with the blower control set to the “O” (or OFF) posi[...]

fresh air and high blower settings. This will ensur e adequate system lubrication to minimize the possibility of compressor damage when the system is started again. W indow Fogging Interior fogging on the windshield can be quickly re- moved by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield an[...]

Control Setting Suggestions for V arious W eather Conditions UNDERST ANDING YOUR INSTRUMENT P ANEL 237 4[...]

[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ................... 2 4 3 ▫ Manual T ransmission ................ 2 4 3 ▫ Automatic T ransmission .............. 2 4 5 ▫ Keyless Go ....................... 2 4 6 ▫ Normal Starting .................... 2 4 6 ▫ Extremely Cold W eather (Below ⫺ 20°F Or ⫺ 29°C) .................[...]

▫ 5-Speed Automatic T ransmission (5.7L Engine) ........................... 2 6 5 䡵 AutoStick 威 — If Equipped .............. 2 6 9 ▫ AutoStick 威 — 3.5L Engine ............. 2 6 9 ▫ AutoStick 威 — 5.7L Engine ............. 2 7 0 䡵 Driving On Slippery Surfaces ............ 2 7 1 ▫ Acceleration ....................... 2 7 1 ▫ [...]

▫ Synchronizing ESP .................. 2 8 7 ▫ ESP/BAS Malfunction Indicator Light And ESP/TCS Indicator Light ............... 2 8 8 䡵 T ire Safety Information ................ 2 8 9 ▫ T ire Markings ..................... 2 8 9 ▫ T ire Loading And T ire Pressur e ......... 2 9 4 䡵 T ires — General Information ............ 2 9 6 ▫ T [...]

▫ Reformulated Gasoline ............... 3 1 7 ▫ Gasoline/Oxygenate Blends ........... 3 1 7 ▫ E-85 Usage In Non-Flex Fuel V ehicles ..... 3 1 7 ▫ MMT In Gasoline ................... 3 1 8 ▫ Materials Added T o Fuel .............. 3 1 9 ▫ Fuel System Cautions ................ 3 1 9 ▫ Carbon Monoxide W arnings ........... 3 2 0 䡵 Addi[...]

ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instr uct all other occupants to buckle their seat belts. W ARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or [...]

Normal Starting with Integrated Key — Manual T ransmission Normal starting of either a cold or a warm engine does not requir e pumping or depressing the accelerator pedal. Press the clutch pedal fully to the floor , and turn the ignition switch to the ST AR T position and release when the engine starts. If the engine fails to start within 15 seco[...]

Automatic T ransmission The shift lever must be in the NEUTRAL or P ARK position before you can start the engine. Apply the brakes before shifting into any driving gear . CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift i[...]

Keyless Go This feature allows the driver to oper - ate the ignition switch with the push of a button, as long as the ENGINE ST AR T/STOP button is installed and the Remote Keyless Entry transmitter is in the passenger compartment. Installing and Removing the ENGINE ST AR T/STOP Button Installing the Button 1. Remove the ignition key . 2. Insert th[...]

T o start the engine, the transmission must be in P ARK or NEUTRAL. Press and hold the brake pedal while pr ess- ing the ENGINE ST AR T/STOP button once. The system takes over and attempts to start the vehicle. If the vehicle fails to start, the starter will disengage automatically after 10 seconds. If you wish to stop the cranking of the engine pr[...]

NOTE: If the ignition switch is left in the ACC position the system will automatically time out after 60 minutes of inactivity and the ignition will switch to the OFF position. T o T urn Off the Engine Using ENGINE ST AR T/STOP Button — Manual T ransmission Only 1. W ith the vehicle stopped, place the shift lever in NEUTRAL, then press and r elea[...]

ST AR T . T o change the ignition switch positions without starting the vehicle and use the accessories follow these steps. • Starting with the ignition switch in the OFF position: • Press the ENGINE ST AR T/STOP button once to change the ignition switch to the ACC position (EVIC displays “IGNITION MODE ACCESSOR Y”), • Press the ENGINE ST[...]

W ARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic transmission cannot be started this way . Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a dis- charged battery , booster cab[...]

and hold the clutch pedal, push the accelerator pedal all the way to the floor and hold it, then press and hold the ENGINE ST AR T/STOP button for no more than 15 sec- onds. Release the accelerator pedal and the clutch pedal, wait 10 to 15 seconds, then repeat the “Normal Starting” procedur e. Clearing A Flooded Engine (Using Fob W ith Integrat[...]

W ARNING! Remember to disconnect the cord before driving. Damage to the 1 10-1 15 V olt electrical cord could cause electrocution. MANUAL TRANSMISSION — IF EQUIPPED Six-Speed Manual T ransmission W ARNING! Y ou or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should a[...]

Shifting Fully depress the clutch pedal befor e shifting gears. As you release the clutch pedal, lightly depr ess the accelera- tor pedal. The six-speed manual transmission has a spring that centers the shift lever near third and fourth gear . This spring helps you know which gear you are in when you are shifting. Be car eful when shifting from fir[...]

Recommended Shift Speeds T o utilize your manual transmission efficiently for fuel economy , it should be upshifted as listed in recom- mended shift speed chart. MANUAL TRANSMISSION RECOMMENDED SHIFT SPEEDS Axle Ra- tio 1-4 4-5 5-6 3.73 mph 20 25 42 (km/h) (32) (40) (67) 3.91 mph 20 37 48 (km/h) (32) (59) (77) Earlier upshifts during cruise conditi[...]

1–4 Skip Shift There ar e times when you must shift the transmission directly fr om first gear to fourth gear instead of from first gear to second gear . This is to help you get the best possible fuel economy from your vehicle. This occurs when the engine coolant (antifreeze) is higher than 106°F (41°C), vehicle speed is greater than 19 mph (30[...]

AUTOMA TIC TRANSMISSION — IF EQUIPPED CAUTION! Damage to the automatic transmission may occur if the following precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift [...]

• Shift lever position • Accelerator position • V ehicle speed The gear shifting process is continuously adapted, de- pendent on the driving style, the driving situation, and the road characteristics. NOTE: • After selecting any driving position, wait a moment to allow the gear to engage fully before accelerating, especially when the engine[...]

W ARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into P ARK, remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignit[...]

T o activate the override, first insert the key into the ignition switch and turn it to the ACC or ON position. Then, press the pink-color ed tab through the access port with a small flat-bladed screwdriver or alike. While pressing the override tab, move the shift lever out of the P ARK position. When complete, return the override cover to its orig[...]

4-Speed Automatic T ransmission (3.5L Engine) NOTE: Under extreme cold temperatur es (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only 2nd gear operation. Normal op- eration will resume once the transmission temperatur e has risen to a suitable level. Shifting from DRIVE to P ARK or REVERSE should be done only[...]

When parking on a flat surface, place the shift lever in the P ARK position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the shift lever in P ARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of park. As an added[...]

NEUTRAL The engine may be started in this range. CAUTION! Coasting the vehicle or driving for any other reason with shift lever in NEUTRAL can result in transmis- sion damage. W ARNING! Do not coast in NEUTRAL and never turn of f the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road condi[...]

“3” (Third) This range eliminates shifts into Overdrive. The transmis- sion will operate normally in 1st, 2nd, and 3rd while in this range. The “3” position should also be used when descending steep grades to prevent brake system dis- tress. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will impr[...]

NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant is warm (usu- ally after 1–3 miles [1.6–4.8 km] of driving). Because engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmis- sion is not shifting into Overdrive when cold. This is considered a nor[...]

possible convenience. Y our authorized dealer has diag- nostic equipment to determine if the problem could recur . If the transmission cannot be reset, authorized dealer service is requir ed. 5-Speed Automatic T ransmission (5.7L Engine) Shifting from DRIVE to P ARK or REVERSE should be done only after the accelerator pedal is released and the vehi[...]

When parking on a flat surface, place the shift lever in the P ARK position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the shift lever in P ARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of P ARK. As an adde[...]

NEUTRAL In NEUTRAL, no power is transmitted from the engine to the drive axle. When the brakes are r eleased, the vehicle can be moved freely (pushed or towed). Do not engage NEUTRAL position while driving except to coast when the vehicle is in danger of skidding (e.g., on icy roads). The engine may be started in this range. Use this range for star[...]

under heavy loading conditions (in hilly terrain, travel- ing into strong head winds, or while towing heavy trailers, use the AutoStick 威 mode and select the “3” range. Delayed Shifts in Cold T emperatures During cold temperature operation, you may notice delayed upshifts depending on engine and transmission temperature as well as vehicle spe[...]

NOTE: Even if the transmission can be reset, we r ecom- mend that you visit your authorized dealer at your earliest possible convenience. Y our authorized dealer has diagnostic equipment to determine if the problem could recur . Have the transmission checked at your authorized dealer as soon as possible. If the problem has been momentary , the tran[...]

Autostick 姞 — 5.7L Engine Autostick 威 is a driver-interactive transmission that of fers manual gear shifting to provide you with mor e control of the vehicle. Autostick 威 allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with mor e [...]

• Starting out in second gear is helpful in snowy or icy conditions. • A void using speed control when Autostick 威 is en- gaged. • The transmission will automatically shift up when maximum engine speed is reached while Autostick 威 is engaged. • T ransmission shifting will be more sharper when Autostick 威 is engaged. DRIVING ON SLIPPER[...]

2. Slow down if the road has standing water or puddles. 3. Replace tires when tr ead wear indicators first become visible. 4. Keep tires pr operly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. DRIVING THROUGH W A TER Driving through water mor e than a few inches[...]

CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water , and if there are any obstacles in the way , before driving through the standing wate[...]

W ARNING! • Driving through standing water limits your vehi- cle’ s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water . • Driving through standing water limits your vehi- cle’ s braking capabilities, which increases stop- ping distances. Therefore, after driving through standing water , drive slowly and[...]

W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to t[...]

P ARKING BRAKE The parking brake should always be applied when the driver is not in the vehicle. The brake light in the instrument cluster will turn on when the parking brake is applied and the ignition switch is ON. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application. When parking on a fl[...]

Automatic T ransmission — If Equipped The foot operated parking brake is positioned below the lower left corner of the instrument panel. T o apply the parking brake, push the parking brake pedal down and then remove your foot fr om the pedal. T o release the parking brake, push down on the parking brake pedal and then release. W ARNING! Never use[...]

W ARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power win- dows, other controls, or move the vehicle. • Be sure the parking brake is fully diseng[...]

When the vehicle is driven over 7 mph (1 1 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises ar e the system per- forming its self check cycle to ensure that the ABS system is working properly . This self check occurs each time the vehicle is started and accelerated past 7 mph (1 1 km/h). ABS is act[...]

W ARNING! (Continued) • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer . Just press firmly on your brake pedal when you need to slow down or stop. • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, no[...]

the conventional brake system will continue to operate normally if the Brake W arning Light is not on. If the ABS Light is on, the brake system should be serviced as soon as possible to restor e the benefits of Anti-Lock brakes. If the ABS Light does not come on when the ignition switch is turned to the ON position, have the bulb repair ed as soon [...]

W ARNING! The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ABS cannot prevent accidents, including those re- sulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver[...]

must apply continuous brake pedal pressur e during the stopping sequence. Do not reduce brake pedal pr essure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated. W ARNING! The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing [...]

• Gear selection matches vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle back- ing uphill is in REVERSE gear). W ARNING! There may be situations on minor hills (i.e., less than 8%), with a loaded vehicle, or while pulling a trailer , when the system will not activate and slight rolling may occur . This could caus[...]

8. Rotate the steering wheel back to center and then an additional half-turn to the right. 9. T urn the ignition switch to the OFF position and then back to the ON position. If the sequence was completed properly , the ESP/TCS Indicator Light will blink several times to confirm HSA is disabled. 10. Repeat these steps if you want to return this feat[...]

accelerator and apply as little throttle as possible. Be sur e to adapt your speed and driving to the prevailing r oad conditions. W ARNING! The ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ESP cannot prevent accidents, including those result-[...]

T o turn the ESP ON again, momentarily depr ess the ESP OFF switch and the ESP/TCS Indicator Light will turn off. NOTE: T o improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow , sand, or gravel, it may be desirable to switch to the “Partial Off” mode by momentarily depr essing the ESP OFF switch. On[...]

ESP/BAS Malfunction Indicator Light and ESP/TCS Indicator Light The Malfunction Indicator Light for the ESP is combined with the BAS indicator . The yellow ESP/BAS Malfunction Indicator Light and the yellow ESP/TCS Indicator Light in the instru- ment cluster both come on when the ignition switch is turned to the ON position. They should go out with[...]

TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger) - Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tir e sizing is based on European design standards. T ires designed to this standar d [...]

CAUTION! Do not use two different size tires on the rear wheels, as this can result in rear axle damage. T ire Sizing Chart TIRE SIZING TERMS Size Designation: P = Passenger Car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger Car tire based on Eur opean design standards LT = Light T ruck tire based on U.S. design standar[...]

TIRE SIZING TERMS R = Construction code — ⬙ R ⬙ means radial construction — ⬙ D ⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire ca[...]

TIRE SIZING TERMS Light Load = Light load tire C, D, E = Load range associated with the maximum load a tire can carry at a specified pr essure Maximum Load — Maximum load indicates the maximum load this tire is designed to carry Maximum Pressure — Maximum pressur e indicates the maximum permissible cold tire inflation pr essure for this tire T [...]

TIRE IDENTIFICA TION NUMBER EXAMPLE: DOT MA L9 ABCD 0301 MA = Code repr esenting the tire manufacturing location (two digits) L9 = Code repr esenting the tire size (two digits) ABCD = Code used by the tire manufactur er (one to four digits) 03 = Number repr esenting the week in which the tire was manufactur ed (two digits) —03 means the 3rd week.[...]

Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e is listed on the driver’s side B-Pillar . T ire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size de[...]

axles must not be exceeded. For further information on GA WRs, vehicle loading, and trailer towing, refer to “V ehicle Loading” in this section. T o determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on the T ire and Loading Infor[...]

NOTE: • The following table shows examples on how to calcu- late total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle. • For the following [...]

ST ARTING AND OPERA TING 297 5[...]

W ARNING! (Continued) • Unequal tire pressures can cause steering prob- lems. Y ou could lose control of your vehicle. • Over-inflated or under -inflated tires can affect vehicle handling and can fail suddenly , resulting in loss of vehicle control. • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to dr[...]

once a month. Use a good quality pocket-type gauge to check tire pr essure. Do not make a visual judgement when determining proper inflation. Radial tir es may look properly inflated even when they ar e under-inflated. CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent mo[...]

T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tir e inflation pressur e is very important. Increased tir e pressur e and reduced vehicle loading may be requir ed for [...]

vehicle only . Since this tire has limited tread life, the original tire should be r epaired (or r eplaced) and rein- stalled at the first opportunity . W ARNING! T emporary use spare tires are for emergency use only . W ith these tires, do not drive more than 50 mph (80 km/h). T emporary use spare tires have limited tread life. When the tread is w[...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continu- ously when you are stuck, and do not let anyone near a spinning wheel, no matte[...]

Many states have laws requiring tir e replacement at this point. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to foll[...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredict- able handling and stress to steeri[...]

The 245/45 R20 size tires do not pr ovide adequate clearance for tire chains. NOTE: Do not use tire chains on a compact spar e tire. CAUTION! T o avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good [...]

pavement. Observe the tire chain manufactur er’s instruc- tions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufactur er sug- gest a maximum speed. This notice applies to all chain traction devices, including link and cable (radial[...]

Follow the Maintenance Schedule in Section 8 for the recommended tir e rotation fr equency . Remember , more frequent r otation is permissible if desired. Also, correct for anything causing rapid or unusual wear prior to performing the tire r otation. TIRE PRESSURE MONITOR SYSTEM (TPMS) The T ire Pressur e Monitor System (TPMS) will warn the driver[...]

The TPMS will warn the driver of a low tire pr essure if the tire pr essure falls below the low-pr essure warning limit for any reason, including low temperatur e effects and natural pressur e loss through the tir e. The TPMS will continue to warn the driver of low tire pressur e as long as the condition exists, and will not turn off until the tir [...]

CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when us- ing replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause [...]

• Seasonal temperature changes will af fect tire pr essure, and the TPMS will monitor the actual tire pr essure in the tire. Base System The T ire Pressur e Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pr essure levels. Sensors mounted to each wheel as part of the valve stem transmit tir[...]

off when the fault condition no longer exists. A system fault can occur due to any of the following: 1. Signal interference due to electr onic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumulati[...]

Premium System — If Equipped The T ire Pressur e Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pr essure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pr essure readings to the r eceiver module. NOTE: It is particularly important for you to check the tire p[...]

Should this occur , you should stop as soon as possible and inflate all of the tires with low pr essure (including those flashing in the EVIC graphic) to the vehicle’s recommended cold placar d pressur e value. Once the system receives the updated tir e pressur es, the system will automatically update, the graphic display in the EVIC will stop fl[...]

If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the TPM T elltale Light will no longer flash, and the ⬙ CHECK TPM SYSTEM ⬙ message will no longer display , and a pressure value will display in place of the dashes. A system fault can occur due to any of the [...]

limit, upon the next ignition key cycle, the TPM T elltale Light will remain ON and a chime will sound. In addition, the graphic in the EVIC will still display a flashing pressur e value. 3. After driving the vehicle for up to 20 minutes above 15 mph (25 km/h), the TPM T elltale Light will flash on and off for 75 seconds and then r emain on solid. [...]

United States ..................... KR5S120123 Canada ........................ 2671-S120123 FUEL REQUIREMENTS 3.5L and 5.7L Engines (with Automatic T ransmission) The 3.5L and 5.7L engines (with automatic transmission) are designed to meet all emissions regulations and pr ovide satisfac- tory fuel economy and performance when using high-quality unl[...]

Reformulated Gasoline Many areas of the country r equire the use of cleaner burning gasoline referr ed to as “reformulated gasoline.” Reformulated gasolines contain oxygenates and are spe- cifically blended to reduce vehicle emissions and im- prove air quality . The manufacturer supports the use of r eformulated gaso- lines. Properly blended r [...]

• operate in a lean mode • OBD II “Malfunction Indicator Light” on • poor engine performance • poor cold start and cold drivability • increased risk for fuel system component corr osion T o fix a Non-FFV vehicle inadvertently fueled once with E-85 perform the following: • drain the fuel tank (see your authorized dealer) • change t[...]

Materials Added to Fuel All gasoline sold in the United States is requir ed to contain effective deter gent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefor e, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these[...]

Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed ar ea, such as a garage, and never sit in a parked vehi[...]

NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler door . Fuel Filler Cap Fuel Filler Cap (If Equipped) ST ARTING AND OPERA TING 321 5[...]

CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunc- tion Indicator Light (MIL) to turn on. • T o avoid fuel spillage and overfilling, do[...]

Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “Check Gascap” message will display in the Electronic V ehicle Information Center (EVIC). If this occurs, tighten the fuel filler cap properly and pr ess the TRIP ODOM- ETER button to turn off the mess[...]

The bar code allows a computer scanner to read the VIN. Gross V ehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver , passengers, and cargo. The total load must be limited so that you do not exceed the GVWR. Gross Axle W eight Rating (GA WR) The GA WR is the maximum capacity of the front and r ea[...]

Figure out the weight on the fr ont and rear of the vehicle separately . It is important that you distribute the load evenly over the front and r ear axles. Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR. Loading T o load your ve[...]

Gross V ehicle W eight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver , passengers, cargo, and tongue weight. The total load must be limited so that you do not exceed the GVWR. Gross T railer W eight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables, and equipment (perma[...]

Frontal Area The frontal ar ea is the maximum height and maximum width of the front of a trailer . T railer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trai[...]

W ARNING! • An improperly adjusted weight distributing hitch system may reduce handling, stability , braking performance, and could result in an accident. • W eight distributing systems may not be compat- ible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable rec- reational vehicle dealer for additional [...]

Engine/T ransmission Frontal Area Max. GTW (Gross T railer Wt.) Max. T ongue Wt. 3.5L Automatic 12 sq ft (1.1 1 sq m) 1,000 lbs (454 kg) 100 lbs (45 kg) 5.7L Automatic 12 sq ft (1.1 1 sq m) 1,000 lbs (454 kg) 100 lbs (45 kg) Refer to local laws for maximum trailer towing speeds T railer and T ongue Weight Always load a trailer with 60% to 65% of th[...]

Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer . • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. [...]

W ARNING! (Continued) Make certain that the load is secured in the trailer and it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. Y ou could lose control of your vehicle and have an accident. • When hauling cargo or towing a trailer , do [...]

T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tir e. − Proper tir e inflation pressur es are essential to the safe and satisfactory operation of your vehicle. Refer to “T ires–General Information” for proper tir e inflation procedur es. − Also, check the trailer tires for pr oper tire infl[...]

CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes, and they should be of adequate capacity . Failure to do this could lead to accelerated brake lining wear , higher brake pedal effort, and longer stopping distances. W ARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. I[...]

4-Pin Connector 1 — Female Pins 4 — Park 2 — Male Pin 5 — Left Stop/T urn 3 — Ground 6 — Right Stop/T urn 7-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 — Left Stop/T urn 3 — Right Stop/T urn 7 — Running Lamps 4 — Electric Brakes 334 ST ARTING AND OPERA TING[...]

T owing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away fr om heavy traffic. T owing T ips — Automatic T ransmission The DRIVE range can be selected when towing. How- ever , if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3?[...]

− Extended driving at high RPM should be avoided to prevent excess heat generation. A reduction in vehicle speed may be requir ed to avoid extended driving at high RPM. Return to a higher gear range or vehicle speed when road conditions and RPM level allows. T owing T ips — Cooling System T o reduce potential for engine and transmission over - [...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ............... 3 3 8 䡵 If Y our Engine Overheats ............... 3 3 8 䡵 TIREFIT T ire Repair — If Equipped ....... 3 3 9 䡵 Jacking And T ire Changing .............. 3 4 5 ▫ Jack Location/Spare T ire Stowage ....... 3 4 5 ▫ Preparations For Jacking .............. 3 4 7 ?[...]

HAZARD W ARNING FLASHER The Hazard W arning flasher switch is located in the switch bank near the bottom center of the instrument panel. Press the switch to turn on the Hazar d W arning flashers. When the Hazard W arning flasher switch is activated, all directional turn signals will flash on and off to warn oncoming traf fic of an emergency . Press[...]

the fan control to high. This allows the heater cor e to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads 240°F (1 16 °C) or greater pull over and stop the vehicle. Idle the vehicle with the air conditi[...]

The TIREFIT system is located under an access panel in the trunk. 1. Air pump hose 2. Power plug and cable 3. AIR PUMP switch 4. Pressur e gauge TIREFIT Location TIREFIT Kit 340 WHA T TO DO IN EMERGENCIES[...]

5. TIREFIT sealant bottle 6. TIREFIT sealant hose W ARNING! • Do not attempt to repair a tire on the side of the vehicle close to traffic. Pull far enough of f the road to avoid the danger of being hit when operating the jack or repairing a tire. • Cuts or punctures larger than approximately 0.16 in (4 mm), tire damage caused by driving with ex[...]

Sealing T ire with TIREFIT 1. T urn on the Hazard W arning Flashers. 2. Move the shift lever into P ARK (automatic transmis- sion) or in gear (manual transmission), turn OFF the engine and set the parking brake. 3. Remove the TIREFIT kit from the tr unk. 4. Pull the power plug 2 and the TIREFIT sealant hose 6 out from the TIREFIT kit. 5. Unscrew th[...]

13. T urn on the Hazard W arning Flashers. 14. Move the shift lever into P ARK (automatic transmis- sion) or in gear (manual transmission), turn OFF the engine and set the parking brake. 15. Disconnect the air pump hose 1 from the underside of the sealant bottle 5 by flipping the hose valve open. 16. Connect the air pump hose valve to the tire valv[...]

24. Connect the air pump hose valve to the tire valve and flip the hose valve closed. 25. Check the pressur e in the tire by r eading the pressure gauge 4. If the pressur e is 19 psi (1.3 bar) or greater , proceed to the following step. NOTE: If the pr essure is less than 19 psi (1.3 bar), the tire is too badly damaged. Do not attempt to drive the [...]

• If TIREFIT is liquid, clean water and a damp cloth will remove the material fr om the vehicle or tire and wheel components. Once TIREFIT sealing material has dried, it can easily be peeled off and pr operly discarded. • Do not exceed 55 mph (90 km/h) until the tire has been inspected. JACKING AND TIRE CHANGING W ARNING! • Do not attempt to [...]

NOTE: The spare tir e must be removed in or der to access the jack. 1. Open the trunk. 2. Lift the access cover using the pull strap. 3. Remove the fastener securing the spare tir e. 4. Remove the spare tir e. 5. Remove the fastener securing the jack. Opening The Access Panel Spare T ire Fastener 346 WHA T TO DO IN EMERGENCIES[...]

W ARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Preparations For Jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible. A void icy or slippery areas. 2. Set the [...]

NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking and Changing a Tire W ARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Bl[...]

1. Remove the spare tir e, jack, and lug wrench. 2. If equipped with steel wheels, do not remove the wheel cover at this time. If equipped with aluminum wheels where the center cap covers the lug nuts, use the lug wrench to pry the center cap of f carefully befor e raising the vehicle. W ARNING! T o avoid possible personal injury , handle the wheel[...]

3. Before raising the vehicle, use the lug wr ench to loosen, but not remove, the lug nuts on the wheel with the flat tire. T urn the lug nuts counter clockwise one turn while the wheel is still on the ground. 4. Place the jack underneath the lift area that is closest to the flat tire. T urn the jack scr ew clockwise to firmly engage the jack saddl[...]

W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts, wheel cover (if equipped), and tire. Remove the cover by hand. Do not pry it of f. 7. Mount the spare tir e. NOTE: For vehicles so equipp[...]

W ARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Compact Spare Tire The compact spare tir e is for temporary emergency use with radial tires. It is engineer ed to be used on your style vehicle only . Since th[...]

1. Mount the road tir e on the axle. For vehicles equipped with wheel covers, perform Steps 2 and 3. For vehicles equipped with center caps, proceed to Step 4. 2. Install two lug nuts on the mounting studs, which are on each side of the stud that is in alignment with the valve stem. Install the lug nuts with the cone shaped end of the nut toward th[...]

snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover . 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. T o avoid the risk of forcing the vehicle of f the jack, do not tighten the lug nuts fully until the vehicle is lowered to the g[...]

JUMP-ST ARTING W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON. Y ou can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic transmission cannot be started this way . Unburned fuel could ent[...]

NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals ar e located in the engine compartment for jump-starting. 1. W ear eye protection and r emove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park th[...]

7. Start the engine in the vehicle that has the booster battery . Let the engine idle a few minutes. Then, start the engine in the vehicle with the discharged battery . NOTE: Refer to ⬙ Synchronizing ESP ⬙ under ⬙ Electr onic Stability Program ⬙ in Section 5 if the ESP/BAS light (in the instrument cluster) r emains on continuously after sta[...]

W ARNING! (Continued) • During cold weather when temperatures are be- low the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode. The battery temperature must be brought above the freezing point before attempting jump-start. FREEING A STUCK VEHICLE If your vehi[...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed. TOWING A DISABLED VEH[...]

If the transmission is not operative or if the vehicle is to be towed more than 30 miles (48 km), the vehicle must be transported using a flatbed truck. CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • If the transmission is not operative or if the vehicle i[...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.5L ............ 3 6 3 䡵 Engine Compartment — 5.7L ............ 3 6 4 䡵 Onboard Diagnostic System — OBD II ..... 3 6 5 ▫ Loose Fuel Filler Cap ................ 3 6 5 䡵 Emissions Inspection And Maintenance Programs ............................ 3 6 6 䡵 Replacement Parts ....[...]

▫ Brake System ...................... 3 8 5 ▫ Clutch Hydraulic System — Manual T ransmission (If Equipped) ............. 3 8 7 ▫ Manual T ransmission — If Equipped ..... 3 8 7 ▫ Automatic T ransmission — If Equipped . . . 387 ▫ Rear Axle ........................ 3 8 9 ▫ Appearance Care And Protection From Corrosion ...............[...]

ENGINE COMP ARTMENT — 3.5L 1 — Integrated Power Module 6 — Engine Coolant Reservoir 2 — Air Cleaner Filter 7 — Engine Oil Fill 3 — Brake Fluid Reservoir Access Cover 8 — Engine Oil Dipstick 4 — Coolant Pressur e Cap 9 — W asher Fluid Reservoir 5 — Power Steering Fluid Reservoir 10 — Remote Jump-Start Positive Battery Post MAIN[...]

ENGINE COMP ARTMENT — 5.7L 1 — Integrated Power Module 6 — Air Cleaner Filter 2 — Coolant Pressur e Cap 7 — Engine Oil Fill 3 — Brake Fluid Reservoir Access Cover 8 — Engine Oil Dipstick 4 — Engine Coolant Reservoir 9 — Remote Jump-Start Positive Battery Post 5 — Power Steering Fluid Reservoir 10 — W asher Fluid Reservoir 364 [...]

ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems ar e operating properly , your vehicle will provide excellent performance and fuel economy , as wel[...]

T rip Odometer button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the MIL. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of this vehi[...]

5. Approximately 15 seconds later , one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition key or start the engine. This means that the vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all a[...]

DEALER SERVICE Y our authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner . Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedur e yourself. NOTE: Intentional tamp[...]

The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level r eadings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding 1.0 qt (1.0 L) of oil when the reading is at the MIN ma[...]

NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever occurs first. Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that ar e API Certified and meet the requir ements of Chrysler Material [...]

The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compart- ment” in this section. Lubricants that do not have both, the engine oil certifi- cation mark and the correct SAE viscosity grade number should not be used. Synthetic Engine Oils [...]

Engine Air Cleaner Filter Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. W ARNING! The air induction system (air cleaner , hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner , hoses, etc.) unless such removal is necessary for re[...]

W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water . • Battery gas is flammable and explosive. Kee[...]

W ARNING! (Continued) • The battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented). CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative [...]

W ARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. T o avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrof[...]

Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner . This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using t[...]

W ARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in t[...]

CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly . Contin- ued operation of your vehicle with a severe malfunction could cause the co[...]

T o minimize the possibility of catalyst damage: • Do not shut off the engine or interr upt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle (automatic transmission only). • Do not idle the engine with any spark plug wires disconnected or removed, suc[...]

system should be drained, flushed, and refilled with fresh coolant. Check the fr ont of the radiator for any accumulation of bugs, leaves, etc. If dirty , clean by gently spraying water from a gar den hose vertically down the face of the condenser . Check the coolant recovery bottle tubing for brittle r ub- ber , cracking, tears, cuts, and tightnes[...]

CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOA T engine coolant (antifreeze), may result in engine damage and may decrease corro- sion protection. If a non-HOA T engine coolant (antifreeze) is introduced into the cooling system in an emergency , it should be replaced with the specified engine coolant (antifreeze) as soo[...]

When adding engine coolant (antifreeze): • The manufacturer r ecommends using MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Organic Additive T echnology). • Mix a minimum solution of 50% HOA T engine coolant (antifreeze) and distilled water . Use higher concentra- tions (not to exceed 70%) if temperatures below ⫺ 34[...]

W ARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. T o prevent scalding or injury , do not remove [...]

of this. As long as the engine operating temperature is satisfactory , the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (kilometers[...]

• Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for Summer or W inter operation. If replacement is ever necessary , install ONL Y the corr ect type thermostat. Other designs may result in unsatisfactory engine coolant (antifr eeze) p[...]

Overfilling of fluid is not recommended because it may cause leaking in the system. Add enough fluid to bring the level up to the requir e- ments described on the brake fluid reservoir . W ith disc brakes, fluid level can be expected to fall as the brake pads wear . However , low fluid level may be caused by a leak and a checkup may be needed. Use [...]

Clutch Hydraulic System — Manual T ransmission (If Equipped) The clutch hydraulic system is fed by a segregated volume of fluid within the brake system master cylinder reservoir . In the event of leakage or wear , use only the manufacturer’s r ecommended brake fluid. Refer to “Flu- ids, Lubricants, and Genuine Parts” in this section for the[...]

If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level. CAUTION! • Using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than that recommend[...]

Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor - mance. Use only manufacturer ’s recommended transmis- sion fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. It is important that the transmission fluid be maint[...]

parking, which exposes your vehicle to airborne contami- nants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extr eme condi- tions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corr osio[...]

CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the under carriage at least once a month. • It is important that the drain holes in the lower edges of the doo[...]

heavy soil and/or excessive brake dust, use MOP AR 威 Wheel Cleaner (05066247AB) or equivalent or select a nonabrasive, non-acidic cleaner . Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOP AR 威 or equivalent is recommended. Do not use oven cleaner . A void automatic car washes that use acidic solutions or harsh[...]

Cleaning Headlights Y our vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and ther efore differ ent lens cleaning procedur es must be followed. T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with [...]

Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use MOP AR 威 T otal Clean, a mild soap solution, or lukewarm water . Do not remove the belts from the vehicle to wash them. Replace the belts if t[...]

CAUTION! • When installing the integrated power module cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the [...]

Cavity Car- tridge Fuse Mini- Fuse Description 8 — 25 Amp Neutral Starter 9— — — 10 30 Amp Pink — W indshield W iper 1 1 30 Amp Pink — Anti-Lock Brake System (ABS) V alves 12 40 Amp Green — Radiator Fan Lo/High 13 50 Amp Red — Anti-Lock Brake System (ABS) Pump Motor 1 4——— Cavity Car- tridge Fuse Mini- Fuse Description 15 50 A[...]

Rear Power Distribution Center There is also a power distribution center located in the trunk under the spar e tire access panel. This center contains fuses and relays. Access Panel Rear Power Distribution Center MAINT AINING YOUR VEHICLE 397 7[...]

CAUTION! • When installing the power distribution center cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having [...]

Cavity Car- tridge Fuse Mini- Fuse Description 8 — 15 Amp Blue Diagnostic Link Connec- tor (DLC)/W ireless Con- trol Module (WCM)/ W ireless Ignition Node (WIN) 9 — 20 Amp Y ellow Power Outlet 1 0——— 11 * ——— 12 * ——— 13 * ——— 14 — 10 Amp Red AC Heater Control/ Cluster/Security Mod- ule - if equipped 1 5——— 1 6?[...]

Cavity Car- tridge Fuse Mini- Fuse Description 28 — 10 Amp Red Ignition Run 29 — 5 Amp Orange Cluster/Electronic Sta- bility Program (ESP)/ Powertrain Control Module (PCM)/STOP LIGHT Switch 30 — 10 Amp Red Door Modules/Power Mirrors/Steering Con- trol Module (SCM) 3 1——— 3 2——— 3 3——— 3 4——— Cavity Car- tridge Fuse Min[...]

Cavity Car- tridge Fuse Mini- Fuse Description 41 — 10 Amp Red AC Heater Control/ Headlights/T ire Pres- sure Monitoring - if equipped 42 30 Amp Pink — Front Blower Motor 43 30 Amp Pink — Rear W indow Defroster 44 20 Amp Blue — Amplifier - if equipped/ Sunroof - if equipped * Cavities 1 1, 12, and 13 contain self-resetting fuses (circuit br[...]

REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Rear Courtesy/Reading Lights .............. W 5 W Rear Compartment (T runk) Light ............. 5 6 2 Overhead Console Reading Lights ............. 5 7 8 V isor V anity Lights ..................... A6220 Glove Box Light ......................... 1 9 4 Door Courtesy .......................[...]

BULB REPLACEMENT Low Beam Headlight, High Beam Headlight, Park/T urn Light — Models with Halogen Headlights — If Equipped See your authorized dealer for bulb replacement. Low Beam Headlight, High Beam Headlight, and Park/T urn Light — Models with High Intensity Discharge (HID) Headlights — If Equipped HID Headlights The headlights are a typ[...]

NOTE: • If a screwdriver is used, make sur e a soft material is placed between the vehicle body and tool so not to scratch the paint. 2. Rotate the bulb’s socket counterclockwise, and r emove the bulb and socket assembly from the housing. 3. Pull the bulb out of the socket and insert the replace- ment bulb. 4. Install the bulb and socket assemb[...]

3. Remove the fasteners from the back of the tail light assembly . 4. Pull back the trunk liner . 5. Remove the remaining fasteners fr om the back of the tail light assembly . 6. Pull the tail light assembly clear from the vehicle to access the bulbs. MAINT AINING YOUR VEHICLE 405 7[...]

7. Push the electrical connector locking tab to the side. 8. Disconnect the electrical connector . 9. T urn the appropriate bulb and socket assembly coun- terclockwise to r emove it from the tail light assembly . 10. Disconnect the bulb from the socket assembly and install the replacement bulb. 1 1. Reinstall the bulb and socket assembly into the t[...]

Center T ail/Backup Light See your authorized dealer for bulb replacement. Center High-Mounted Stop Light (CHMSL) The CHMSL uses LED lights that are not serviceable separately . The CHMSL must be r eplaced as an assembly , see your authorized dealer . License Light 1. Remove the screws securing the light to the r ear fascia. 2. Remove the bulb and [...]

FLUIDS AND CAP ACITIES U.S. Metric Fuel (Approximate) 3.5 Liter Engine 18 Gallons 68 Liters 5.7 Liter Engine 19 Gallons 72 Liters Engine Oil with Filter 3.5 Liter Engine (SAE 10W -30, API Certified) 6.0 Quarts 5.7 Liters 5.7 Liter Engine (SAE 5W -20, API Certified) 7.0 Quarts 6.6 Liters Cooling System * 3.5 Liter Engine (MOP AR 威 Antifreeze/Coola[...]

FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Organic Additive T echnology) Engine Oil (3.5L Engine) Use API Certified SAE 10W -30 Engine Oil meeting the requirements of Chrysler Material Standard MS-6395. Refer to the[...]

Chassis Component Fluid, Lubricant, or Genuine Part Manual T ransmission MOP AR 威 A TF+4 Automatic T ransmission Fluid Automatic T ransmission MOP AR 威 A TF+4 Automatic T ransmission Fluid Brake Master Cylinder MOP AR 威 DOT 3, SAE J1703 or equivalent should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only rec[...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ..... 4 1 2 䡵 Maintenance Schedule ................. 4 1 2 ▫ Required Maintenance Intervals ......... 4 1 4 8 M A I N T E N A N C E S C H E D U L E S[...]

EMISSION CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emission Contr ol System. These, and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliabilit[...]

NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-r oad for an extended period of time. • U[...]

Once a Month • Check tire pr essure and look for unusual wear or damage. • Inspect the battery , and clean and tighten the terminals as requir ed. • Check the fluid levels of coolant reservoir , brake master cylinder , power steering, and transmission, and add as needed. • Check all lights and other electrical items for correct operation. A[...]

6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tir[...]

18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and[...]

30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the spark plugs (5.7L Engine). ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. Odometer Reading Date Repair Order # Dealer Code Sign[...]

42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate t[...]

54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil an[...]

66,000 Miles (1 10,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . Odometer Reading Date Repair Order # Dealer Code Signature Authorized[...]

78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . Odometer Reading Date Repair Order # Dealer Code Signature Authorized [...]

96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the brake linings; replace if necessary . ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front suspension, tie rod ends and [...]

1 14,000 Miles (190,000 km) or 1 14 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . Odometer Reading Date Repair Order # Dealer Code Signature Authori[...]

126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . ❏ Inspect the rear axle fluid. Odometer Reading Date Repair Order [...]

144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the brake linings; replace if necessary . ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the rear axle fluid. ❏ Inspect the [...]

† This maintenance is recommended by the manufactur er to the owner , but is not requir ed to maintain emissions warranty . W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 4 2 9 ▫ Prepar e For The Appointment .......... 4 2 9 ▫ Prepar e A List ..................... 4 2 9 ▫ Be Reasonable W ith Requests ........... 4 2 9 䡵 If Y ou Need Assistance ................ 4 2 9 ▫ Chrysler L[...]

䡵 Publication Order Forms ............... 4 3 3 䡵 Department Of T ransportation Uniform T ire Quality Grades ........................ 4 3 4 ▫ T readwear ........................ 4 3 5 ▫ T raction Grades .................... 4 3 5 ▫ T emperature Grades ................. 4 3 5 428 IF YOU NEED CONSUMER ASSIST ANCE[...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty . Discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • If an authorized dealership is unable to resol[...]

Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center . Any hearing or speech impaired customer , who has access to a TDD or a conventional teletypewriter (TTY) in the[...]

W ARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contain, or emit, chemicals known to the State of Cal[...]

T o contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY : 1–800–424– 9153), or go to http://www .safercar .gov; or write to: Administra- tor , NHTSA, 400 Seventh Street, SW ., W ashington, D.C. 20590. Y ou can also obtain other information about motor vehicle safety from http://www .safercar .gov [...]

• Diagnostic Procedure Manuals Diagnostic Procedur e Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer -controlled ve- hicle systems and features. They show exactly how to find and correct pr oblems the first time, using s[...]

T readwear The T readwear grade is a comparative rating, based on the wear rate of the tire when tested under contr olled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relative performance of tir es depends upon the actual[...]

W ARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure. 436 IF YOU NEED CONSUMER ASSIST ANCE[...]

INDEX 10[...]

About Y our Brakes .................... 276,278 ABS (Anti-Lock Brake System) ............ 278,281 Adding Engine Coolant (Antifreeze) .......... 3 8 1 Adding Fuel ........................... 3 2 0 Adding W asher Fluid ..................... 3 7 6 Additives, Fuel ......................... 3 1 9 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 37[...]

Automatic Door Locks ................... 30,31 Automatic Headlights .................... 1 2 1 Automatic Oil Change Indicator ............. 1 6 3 Automatic T ransaxle Special Additives ...................... 3 8 9 Automatic T ransmission ........... 260,265,387,388 Adding Fluid ...................... 388,410 Autostick ............................ 2[...]

Parking ............................. 2 7 6 W arning Light ..................... 164,278 Brakes ............................. 278,385 Brake/T ransmission Interlock ............... 2 5 8 Break-In Recommendations, New V ehicle ........ 6 7 Brightness, Interior Lights .................. 1 2 5 Bulb Replacement ..................... 402,403 Bulbs, Light[...]

Compact Spare T ire ...................... 3 0 0 Compass .............................. 1 7 6 Compass Calibration ..................... 1 7 6 Compass V ariance ....................... 1 7 7 Computer , T rip/T ravel .................... 1 7 3 Connector U C I ................................ 2 1 7 Universal Consumer Interface (UCI) ......... 2 1 7 Co[...]

Delay (Intermittent) W ipers ................. 1 2 7 Diagnostic System, Onboard ................ 3 6 5 Dimmer Switch, Headlight ................. 1 2 4 Dipsticks Oil (Engine) ....................... 368,369 Power Steering ........................ 2 7 5 Disabled V ehicle T owing ................... 3 5 9 Disposal Antifreeze (Engine Coolant) ........[...]

Block Heater ......................... 2 5 1 Break-In Recommendations ................ 6 7 Checking Oil Level .................. 368,369 Compartment ...................... 363,364 Coolant (Antifreeze) ................. 379,409 Cooling ............................. 3 7 9 Exhaust Gas Caution .................. 68,320 Fails to Start ..................[...]

Flashers Hazard W arning ....................... 3 3 8 T urn Signal ...................... 70,124,160 Flash-T o-Pass ........................... 1 2 4 Flat T ire Changing ....................... 3 4 5 Flooded Engine Starting ................... 2 4 9 Fluid, Brake ........................... 4 1 0 Fluid Capacities ......................... 4 0 8 Flu[...]

Garage Door Opener (HomeLink 威 ) ........... 1 3 4 Gas Cap (Fuel Filler Cap) ............... 320,365 Gasoline, Clean Air ...................... 3 1 7 Gasoline (Fuel) ......................... 3 1 6 Gasoline, Reformulated ................... 3 1 7 Gauges Coolant T emperature ................... 1 5 9 Fuel ............................... 1 5 8 Odom[...]

Heater ............................... 2 3 0 Heater , Engine Block ..................... 2 5 1 High Beam/Low Beam Select (Dimmer) Switch . . 124 Hill Start Assist ......................... 2 8 3 Hitches T railer T owing ........................ 3 2 8 Holder , Cup ........................... 1 4 6 HomeLink 威 (Garage Door Opener) T ransmitter . . .[...]

Kicker Sound System ..................... 2 2 7 Knee Bolster ............................ 4 6 Lane Change and T urn Signals .............. 1 2 4 Lap/Shoulder Belts ....................... 3 7 LA TCH (Lower Anchors and T ether for CHildren) ............................ 61,63 Latches ................................ 7 0 Hood .........................[...]

High Beam/Low Beam Select ............. 1 2 4 Illuminated Entry ....................... 1 9 Instrument Cluster .................. 120,158 Intensity Control ...................... 1 2 5 Interior .......................... 125,133 License ............................. 4 0 7 Lights On Reminder .................... 1 2 3 Low Fuel ......................[...]

Maintenance Free Battery .................. 3 7 2 Maintenance, General ..................... 3 6 8 Maintenance Procedur es ................... 3 6 8 Maintenance Schedule .................... 4 1 2 Maintenance, Sunroof ..................... 1 4 3 Malfunction Indicator Light (Check Engine) . . 168,366 Manual, Service ......................... 4 3 3 M[...]

Checking ......................... 368,369 Dipstick .......................... 368,369 Disposal ............................ 3 7 1 Filter ............................ 371,409 Filter Disposal ........................ 3 7 1 Identification Logo ..................... 3 7 0 Materials Added to ..................... 3 7 1 Recommendation ..................[...]

Seats ............................... 1 1 3 Steering .......................... 274,275 Sunroof ............................. 1 4 0 W indows ............................. 3 2 Power Steering Fluid ..................... 4 1 0 Pregnant W omen and Seat Belts .............. 4 5 Preparation for Jacking .................... 3 4 7 Pretensioners Seat Belts [...]

Replacement T ires ....................... 3 0 3 Reporting Safety Defects ................... 4 3 2 Resetting Oil Change Indicator .............. 1 6 3 Restraint, Head ......................... 1 1 5 Restraints, Child ......................... 5 8 Restraints, Occupant ...................... 3 6 Rocking V ehicle When Stuck ................ 3 5 8 Rot[...]

Rear Folding ......................... 1 1 7 Seatback Release ....................... 1 1 7 T ilting .............................. 1 1 3 Security Alarm (Theft Alarm) ................ 1 8 Selection of Coolant (Antifreeze) .......... 380,409 Selection of Oil ......................... 3 7 0 Sentry Key (Immobilizer) ................... 1 5 Sentry Key [...]

Cold W eather ......................... 2 4 9 Emergency (Jump Starting) ............... 3 5 5 Engine Fails to Start .................... 2 4 9 Remote .............................. 2 6 Starting and Operating .................... 2 4 3 Starting Procedur es ...................... 2 4 3 Steering Column Controls ...................... 1 2 3 Column Lock[...]

TIREFIT .............................. 3 3 9 T i r e s ............................ 70,296,434 Aging (Life of T ires) .................... 3 0 3 Air Pressur e .......................... 2 9 6 Chains .............................. 3 0 4 Changing ......................... 345,348 Compact Spare ........................ 3 0 0 Flat Changing ............[...]

T owing V ehicle Behind a Motor Home ......... 3 3 6 T raction Control ......................... 2 8 2 T railer T owing .......................... 3 2 5 Cooling System T ips .................... 3 3 6 Hitches ............................. 3 2 8 Minimum Requirements ................. 3 3 0 T i p s ................................ 3 3 5 T railer and [...]

Unleaded Gasoline ....................... 3 1 6 Untwisting Procedur e, Seat Belt .............. 4 2 V anity Mirrors ........................... 7 7 V ariance, Compass ....................... 1 7 7 V ehicle Certification Label ................. 3 2 3 V ehicle Identification Number (VIN) ............ 6 V ehicle Loading ................... 294,323,325[...]

INST ALLA TION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to pr ovide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power[...]

2009 CHALL ENGER CHAL LENGER Chrysler LL C 81-226-0916 Second Edition Printed in U.S.A. OWNER ’S MANUAL 2009 147914 Dodge LC22 Challenger.indd 1 9/8/08 3:39:42 PM[...]