Electro-Voice 2.1P Bedienungsanleitung

Electro-V oice ® EVID 12.1P User Manual[...]

Electro-V oice ® T able of Contents Product Description ................................................................................. 1 Product Feature Identification .................................................................. 1 Packing List ............................................................................................. 2 [...]

Electro-V oice ® Product Description The 12.1P is a self cont ained, powered 12" subwoofer providing over 300 watt s continuous output to the speaker . The 12.1P makes the addition of a subwoofer to a EVID system very easy and ef ficient. Since the unit is self-powered, the full range satellite speakers can be powered independently from the s[...]

Electro-V oice ® Packing List Figure 4: EVID TM 12.1P Packing List 2 Below is a list of p arts included with the EVID TM 12.1P subwoofer . The part s are illustrated in Figure 4. A. EVIDTM 12.1P B. W all/Corner Mounting Bracket C. (4) Rubber Mounting Feet D. (2) Speaker Mounting Clips E. Eyebolt F . Right Angle Power Cord G . Owner s Manual H. [...]

Electro-V oice ® S tep-by-S tep Installation & Wiring S tep 1: Mount the Bracket The mounting bracket can be inst alled two ways (see Figures 5 and 6), allowing optimal configurations for installations. Leave 1.5" of sp ace between the bracket and the ceiling when inst alling in a corner! A ttach the bracket to the wall with suitable fast[...]

Electro-V oice ® 4 Figure 7: Wiring Configuration S tep 3: Wire the Speaker A typical wiring configuration is shown in Figure 7. It is highly advisable to support the unit while these connections are being made. When mounting the speaker in a corner mount configuration, a right angle XLR connector such as Neutrik #NC3MRC or equiv . is required for[...]

Electro-V oice ® 5 enclosure hangs from the top clip, always inst all the lower one to secure against possible disengagement of the top clip. S traighten the EV® logo and press firmly at its center to seat it securely into it s mounting hole. For midwall mounting Attach the four rubber mounting feet inside the corners on the side of the enclosure[...]

Electro-V oice ® 6 Mounting through a suspended ceiling grid On the rear of the enclosure install and tighten two 3/8-16-thread forged steel eyebolt s (one is included) with a 3/8" flat washer under each. Cut two pieces of ordinary drop ceiling L angle (wall track) 23 3/4" long and screw them to the top and bottom of the enclosure with 3[...]

Electro-V oice ® 7 Safety Agency Compliance The EVID 12.1P bracket system has successfully p assed EIA 636 at a safety factor of 6:1. The bracket system is intended to support the EVID 12.1P only . Do not use it for any other purpose. Never set anything on, or hang anything from, the EVID 12.1P enclosure when using this bracket. For a cop[...]

Electro-V oice ® 8 Obtaining Warranty Service T o obtain warranty service, a customer must deliver the product, prepaid, to Electro-V oice® Service or to any of it s authorized service representatives, together with proof of purchase of the product in the form of a bill of sale or receipted invoice. A list of authorized service representatives is[...]

Electro-V oice ® 9 • Higher-level foreground music in bass heavy applications such as dance floors, amusement arcades, or loud bars: use one pair of EVID 6.2s for each 12.1P . • For example, a large hotel might use eight 3.2s and two 12.1Ps in the dining room, eight 4.2s and two 12.1P s in the lounge, four 6.2s with two 12[...]

Electro-V oice ® 10 Appendix C: Painting Process • Remove the four screws securing the front hatch and lift of f the hatch p anel. Carefully twist and lift off the EV® logo and set it aside. • The foam grille blocks are held in place by sharp pins protruding through the baffle board. Note the relative position of the foam and carefully lift t[...]

Electro-V oice ® 11 Appendix D: T roubleshooting Guide Problem Possible Cause(s) Action 1. No sound Amplifier V erify that that the line level signal cables XLR connector has been pushed all the way into the Low Level In jack on the amplifier panel. T urn the Power  switch on and the volume up until you can hear sound emitting from [...]

Electro-V oice ® 12 Appendix E: T echnical Specifications Frequency Response (-10 dB): 42 Hz  160 Hz Max Calculated SPL 1 @ 1M: 126 dB LF Amplifier Power: 650W 50ms Burst, 300W Continuous Line Input Sensitivity: -12 dBu to 0 dBu for Full Output LF T ransducer: 12 (300 mm) High-Excursion Dual V oice-Coil Connectors: Line Input s: XLR Balanced[...]

Electro-V oice ® 13 Notes[...]

Electro-V oice ® U.S.A. and Canada: For customer orders, contact the Customer Service department at: 800/392-3497 Fax: 800/955-6831 For warranty repair or service information, contact the Service Repair Department at: 800/685-2606 For technical assistance, contact T echnical Support at: 866/78-AUDIO S pecifications subject to change without notice[...]