Electrolux SDS51400S0 Bedienungsanleitung

SDS51400S0 EN FRIDGE-FREEZER USER MANUAL[...]

FOR PERFECT RE SULTS Thank you for choosing th is AEG product. We have created it to give you impeccable performance for many years, with innovative techno logies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minute s reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AE[...]

CONTENTS 4 Safety information 6 Operation 7F i r s t u s e 7D a i l y u s e 8 Helpful hints and tips 9 Care and cleaning 11 What to do if… 13 Technical data 13 Installation 20 Environmental concerns The following symbols are used in this user manual: Important information concerning your personal safety and information on how to avoid damaging th[...]

SAFETY INFORMATION In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistak es and accidents, it is importan t to ensure tha t all people using the appliance are thoroughly familiar with it s operation[...]

• It is dang erous to alter the specifications or modify this product in any way. Any dam - age to the cord may cause a short-ci rcuit, fire and/or electric sh ock. WARNING! Any electrical component (power cord, plug, co mpressor) must be replaced by a certified service agent or qualified service personnel. 1. Power cor d must not be lengthe ned.[...]

• Adequate air circulation should be around th e appliance, lacking this leads to overheat - ing. To achieve sufficient ventilation follow the instructions relevant to installation. • Wherever possible th e back of the product should be against a wall to avoid touching or catching warm parts ( compressor, condenser) to prevent possible burn. ?[...]

• the location of the appliance. If the ambient temperature is high or the ap pliance is fully loaded, and the appliance is set to the lowest temperatures, it may run continuously causing frost to form on the rear wall. In this case the dial must be se t to a higher temperature to allow automatic defrosting and therefore reduced ener gy consumpti[...]

The numbers indicate storage times in months for the appropriate types of fro zen goods. Whether the upper or lower value of the indi cated storage time is valid depends on the quality of the foods and tr eating before freezing. Ice-cube production This appliance is equipped wi th one or more trays for the pr oduction of ice-cubes. Fill these trays[...]

• only freeze top quality, fresh and thoroughly cleaned, foodstuffs; • prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required; • wrap up the food in aluminium foil or poly thene and make sure that the packages are airtight ; • do not allow fresh[...]

Take care of not to damage the coolin g system. Many proprietary kitchen surface cleaners co ntain chemicals that ca n attack/damage the plastics used in this appliance. For this reason it is recommended th at the outer casing of this appliance is only cleaned with warm water with a little washing-up liquid added. After cleaning, reconnect the equi[...]

4. When defrosting is co mpleted, dry the interior thoroughly. 5. Switch on the appliance. 6. After two or three hours, reload the previously removed food into the compartment. Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. Do not use a mechanical device or any artifi cial means to spe ed up the thawing [...]

Problem Possible cause Solution The door is not closed correctl y. Refer to "Closing the door". The door has been opened too frequently. Do not keep the door open lon - ger than necessary. The product temperature is too high. Let the product temperature de - crease to room temperature b e - fore storage. The room temperature is too high. [...]

3. Remove the lamp cover (refer to the il - lustrati on). 4. Replace the used lamp with a new lamp of the same power and specifically de - signed for household appliances. (the maximum power is shown on the lamp cover). 5. Install the lamp cover. 6. Tighten the screw to the lamp cover. 7. Connect the mains plug to the mains socket. 8. Open the door[...]

Climate class Ambient temperature SN +10°C to + 32°C N +16°C to + 32°C ST +16°C to + 38°C T +16°C to + 43°C Electrical connection Before plugging in, ensure that the voltage and frequency shown on the rating plate cor - respond to your do mestic power supply. The appliance must be earthed. The power su pply cable plug is provided with a con[...]

4. Loos en the middle h inge. 5. Remove the lower door. 6. Loosen and remove the lo wer pin. On the opposite side: 1. Tighten the lower pin. 2. Install the lower door. 3. Tighten the middle hinge. 4. Install the spacer. 5. Install the upper door. 6. Tighten the upper pin. Ventilation requirements The airflow behi nd the appliance must be suffi - ci[...]

1. Apply the adhesive sealing str ip to the appliance as shown in figure. 2. Install the appliance in the niche. Push the appliance in the direction of the arrow (1) until the upper gap cover stops against the kitchen furniture. Push the appliance in the direction of the arrow (2) against the cupboard on the opposite side of the hinge. 3. Adjust th[...]

4. Attach the appliance to the niche with 4 screws. 5. Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case. 6. Attach the covers (C, D) to the lugs and the hinge holes. Install the vent grille (B). Attach the hinge covers (E) to the hinge. I I B E E D C Installation 17[...]

7. Disconnect the parts (Ha), (Hb), (Hc) and (Hd). 8. Install the par t (Ha) on the inner s ide of the kitchen f urniture. 9. Push the part (Hc) on the part (Ha). ca. 50 mm ca. 50 mm 21 mm 90° 90° 21 mm Ha Hc 18 Installation[...]

10. Open the appliance door and the kitch - en furnitur e door at an angle of 90°. Insert the small squa re (Hb) into guide (Ha). Put together the appliance do or and the furniture door and mark the holes. 11. Remove the brackets and mark a dis - tance of 8 mm from the outer edge of the door where the nail must be fitted (K). 12. Place the small s[...]

13. Press the part (Hd) on the pa rt (Hb). 14. To open the doors do these step s. Use the sliding system previously illus - trated or open one of the two doors by fitting the small handle supplied as an acces - sory. Do a final check to make sure that: • All screws are ti ghtened. • The sealing strip is attached tightly to the cabinet. • The [...]

21[...]

22[...]

23[...]

www.aeg-electrolux.com/shop 212720 301-00-20052010[...]