Emerson KF160OI01 Bedienungsanleitung

Net Weight: 30.6 Lbs. Part No. F40BP72830004 Form No. BP7283-4 U.L. Model No.: KF160 READ AND SA VE THESE INSTRUCTIONS KF160OI01 Olde Iron with Washed Oak/Honey Maple Blades HIGH COUNTR Y Ceiling Fan Owner's Manual Emerson F ans Designed by Model Number BP7283, High Country, KF160 7/31/06 10:54 AM Page 1[...]

W ARNING: T o avoid fire, shock, and serious personal injury , follow these instructions. Safety Instructions 1. Read your owner ’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidental[...]

3 T ools Needed for Assembly One Phillips head screwdriver One wire stripper One stepladder Six wire connectors (supplied) Three 60-watt (max.) candelabra base bulbs Three 40-watt (max.) cnadelabra base round bulbs Materials Wiring, outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor (2-[...]

General Y our Emerson ceiling fan comes equipped with a remote control transmitter and a remote control receiver . This remote con- trol systems is designed to control your ceiling fan speed, airflow direction, and light intensity . NOTE: An optional SW1 15 Wall Control (not supplied) may also be used with the remote control receiver supplied with [...]

2. Slide the four switch levers on the code switch to your choice of ON (up) or down positions. Use a ball-point pen or small screwdriver and slide the levers firmly up or down. 3. In the receiver (Figure 1), slide the four switch levers to the same positions as set in the transmitter . Make sure the levers on both switches are in the same position[...]

7. Carefully remove the fan motor housing assembly from the lower foam pad. T urn the housing assembly over and position it on the lower foam pad with the fan blades resting on the pad so that the top of the motor faces up. 8. Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 5)[...]

tight against the pin and securely tight- en the setscrew in the hanger ball. A loose setscrew could create fan wobble. DOWNROD DECORA TIVE COVER GROMMET DECORA TIVE SCROLL ASSEMBL Y 40-WA TT CANDELABRA BASE ROUND BULB (3) 10. T ighten the setscrews (Figure 6) secure- ly while pulling up on the downrod. NOTE: The setscrews must be properly installe[...]

2. Carefully lift the fan and seat the hang- er ball/downrod assembly on the hang- er bracket that was just attached to the outlet box (Figure 1 1). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 10). 8 How to Hang Y our Ceiling Fan The fan must be hung with at least 7' of clearance from floor to blades ([...]

9 1. Position the supply wires to the left side of the outlet box (Figure 12); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 12. NOTE: Make all wiring connections using wire connectors (supplied). Make sure that all connections are tigh[...]

NOTE: If you wish to operate your ceil- ing fan with the downlight fixture attached, perform steps 7 and 8. Otherwise, skip to step 9. 7. For Operating Y our Fan With the Downlight Fixture. Remove the thread- ed plug from the light fitter adapter . Feed the black and white wires of the light fitter assembly through the hole in the adapter and screw[...]

10. Screw in three 60-watt (maximum) candelabra base bulbs into the light fitter sockets (Figure 18). Remove and retain the nut and rubber washer from the light fitter threaded nipple. Place the lower glass over the threaded nipple and secure in place using the rubber washer and nut. Place the decorative cap over the threaded nipple, then screw on [...]

12 Operating Y our Ceiling Fan IMPORT ANT Fan installation must be completed, including the installation of the fan blades, before testing of the remote control. Y our remote control (Figure 19) has full control of your fan and light. 1. Restore electrical power to the outlet box by turning the electricity on at the service panel. 2. T o set the de[...]

13 Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock. ! W ARNING The use of any other control not specifically approved for this fan could result in fire, shock and per- sonal injury . ! W ARNING This product is designed to use only those parts supplied with th[...]

14 T rouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not 1. Fuse or circuit breaker 1. Check main and branch start. blown. circuit fuses or circuit breakers. 2. Loose power line connections 2. Check line power connections to the fan, or loose switch wire to fan and switch wire connections in the switch connections in the switch [...]

15 Repair Parts Listing Part Number Key Model No. No. Description KF160OI01 * Hanger Pack, Consisting of: 761655-37 1 Hanger Bracket — 2 Hanger Ball — 3 Downrod — * Parts Bag, Containing: 762658 4 Wire Connector (7) — 5 Threaded Stud, 8-32 X 1-1/4” (2) — 6 Knurled Knob (2) — 7 Lockwasher (2) — 8 Hairpin Pin — 9 Clevis Pin — 10 S[...]

LIMITED WARRANTY What The War ranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. Y ou must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor , this warranty will la[...]