EverFocus EDN850H Bedienungsanleitung

EDN850H User ’ s Manual Copyright © EverFocus Electronics Corp, Release: Dec. 2009 Rev .A[...]

EDN850H 2 Product Name: EAN 850H EverFocus IP Network Cameras Model Number(s): EDN850H FCC Notice "Declara tion of Conformity Information" This equipment has been tested and found to co mply with the limits for a Class A digital devic e, pursuant to part 15 of the FCC Rules. These limits ar e designed to provide reasonable protection agai[...]

EDN850H 3 About this document All the safety and operating instructions shou ld be read and followed before the unit is operated. This manual should b e retained for future reference. The information in this manual was current when publish ed. The manufacturer reserves the right to revise and improve its products. All specifications are therefore s[...]

EDN850H 4 Do not operate the appliance beyond its specified temperature, humidity or power source ratings. D o not use th e appliance in an extreme environ ment where high temperature or high humidity exists. Use the appliance at temperature within 0 ℃ ~ +40 ℃ / 32 ~ 104 and a humidity below 90%. The input power source for this appliance [...]

EDN850H 5 External Dimensions: 56 mm x 68 mm x 101 mm / 2.24” x 2.72” x 4.04” T ABLE OF CONTENTS 1. INTRODUCTION.......................................... .......................................................... 7 2. FEATURES .................................................................................................... .......... 7 3.[...]

EDN850H 6 4.8 SYSTEM ................................................... ......................................................... 51 4.8.1 Date/T ime.................................................................................................... 51 4.8.2 Daylight Saving ..........................................................................[...]

EDN850H 7 1. INTRODUCTION The EDN850H is weatherproof IP66 rated outdoor network dome camera which provides H.264, MPEG-4 and MJPEG compression for multi-streaming capabilities. W ith unique digital processing technology , EDN850H can reduces the g ain noise and produce clear , obv ious images in low light environments. Equipped with build-in SD ca[...]

EDN850H 8 3. ACCESSING THE CAMERA MENU Step 1.S tart an Internet Explorer browser . Step 2. Enter the IP address or host name of the ca mera in the Location/Address field of your Internet Explorer browser . (Please refer to EDN850H Installation Guide for how to find the IP address) Step 3. Input “Use rname” and “Password”. Default Userna me[...]

EDN850H 9 ○ 3 Press button to close EDN850H network pag e. ○ 4 V ideo Stream Select V ideo S tream from Stream 1 / St ream 2, S tream 3 a nd S tream 4. Please refer to “4.4.1 Multi S tre aming” for fu rther information. ○ 5 Vi e w S i z e Y ou can s elect V iew siz e to either reduce or enlarge the i mage to the appropriate view size. Sel[...]

EDN850H 10 ○ 8 Snapshot The Snapshot button saves a snapshot of the video image currently being displayed. The location where th e snapshot data is saved can be spe cified in Setting - > User ’ s Config. Please refer to “4.2 User Config” for further information. ○ 9 ~ ○ 10 Play Audio/Transmit Audio Click the “Play Audio” and “T[...]

EDN850H 11 4. SETTING Click this button to dis play the setup menu.[...]

EDN850H 12 4.1 System Info System information and system log check of the setup menu can be performed on this page. The “System Info” page has 2 tabs: [Information] tab and th e [Log] tab. 4.1.1 Information System Information: Firmware version, MAC address, V ideo T y pe, Model number . (unchangeable, for reference only)[...]

EDN850H 13 4.1.2 Log System Log : Date/Time : displaying date and tim e of the log. Log message : all information and event message, including login, user ’ s IP , reboot, firmware upgrade, load factory default, configuration reset and event detected. System will keep the newest 256 records. Press button to export sy stem log into “.txt” file[...]

EDN850H 14 4.2 User Config Live view configuration is to b e set by user . Each login user can make his/her own settings for the following items: Te x t S e t t i n g Check the box for text of Machine name , Date/Time or Frame Ra te to be displayed on the screen. Te x t C o l o r Foreground Color: Select the foreground color of text to be displayed[...]

EDN850H 15 Position: Select the position where the text will be displaying fro m Upper Left / Lower R ight / Lowe r Left. Press Apply to apply the setting changes or Reset to res et without saving the change. Date/T ime Format Used in T ext Select Date/T i me Format from the following options: T i me Format: 24 Hours or 12 Hours. Press Apply to app[...]

EDN850H 16 Language: Select the language to be di splay ed in web page. Default languag e is English. T o add a new language which is not listed in the orig inal configuration, press the Browse button to locate the new language file (.evb) and then click the Load button. Press Apply to apply the setting changes or Reset to res et without saving the[...]

EDN850H 17 • IP Ty pe • IP address • Subnet mask • Gateway (when using the g ateway server/router) • Prim ary DNS, Sec onda ry DNS ( when using DNS ) • HTTP Port IP SETTING IP T yp e DHCP: Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs w hose IP address is unique. Refer to the ne[...]

EDN850H 18 Primary DNS An IP a ddress of DNS server that is provided by ISP . Secondary DNS If your ISP provides you an IP addres s secondary DNS, please set it here. User name Enter User name of the account (used only for PPPoE). Password Enter Password of the account (used only for PPPoE). Press Apply to apply the setting changes or Reset to res [...]

EDN850H 19 DDNS setting When accessing the ca mera via the Inte rnet fro m the network environment of which the global IP address is obtain ed using DHCP, the DDNS function is necessary. To use the DDNS function, it is necessary to connect to the dedicated DDNS server. We offer 4 DDNS server providers as foll ow: ○ www .everfocusddns.com ○ www [...]

EDN850H 20 Press Apply to apply the setting changes or Reset to res et without saving the change. 4.3.3 Bandwidth Bandwidth Setting Max. Bandwidth: Specify , Unlimited / 64 K/ 128 K/ 256 K / 512 K / 1M / 2M / 4M / 8M bps. the maxi mum bandwidth that the camera is allowed to use on th e network. This is a useful function when connecting the ca mera [...]

EDN850H 21 4.3.4 SMTP/FTP Set SMTP The settings relat ing to the mail s erver used to send the e- mail notification from the camera to predefined add resses via SMTP can be configured. SMTP Server: Enter the IP address or the host name o f the SMTP s erver used to send e-mails . SMTP Port: Enter the port number for SMTP . Default is 25. Authenticat[...]

EDN850H 22 Send T est Mail: Press button to send a testing mail to the assigned address. Set FTP The settings relating to the FTP server used to tran smit the alarm images can be configured. FTP Server: Enter the IP address or the host name of the FTP server. FTP Port: Enter the port number for FTP server . Default is 21. Recording Path: Assign the[...]

EDN850H 23 4.3.5 Network Alarm (reserved for PowerCon) Set Network Alar m This function is reserved for PowerCon software, for th e detail setting please refer to PowerCon network alarm protocol. 4.4 V ideo The settings relating video such as streaming, camera OSD can be configured on this page. The "Video" page has 2 tabs: the [Multi-str[...]

EDN850H 24 4.4.1 Multi S treaming St ream Setting The system can output 4 video stream s simultaneously . For each of them, user can set compression for mat, resolution, quality and frame rate individually . Stream 1 is always enabled for live view . Check “Enable” box to enable other streams. Format: Select encode format from H.264, MPEG4 and [...]

EDN850H 25 Press Apply to apply the setting changes or Reset to res et without saving the change. V ideo Recording Setting User can set video recording by selecting one of the enabled video streamings. This will allow user to view liv e images as well as to record video of the other video streaming. V ideo St ream: Select video recordin g stream fr[...]

EDN850H 26 OSD setting: Use the following buttons on the operation pan el to operate the "Camera OSD setting" using a PC. (Please refer to 4.4.2.1 for detail guide of Camera OSD Setting) [SET] button: Click this button to move to the submenu. [Left] button/ [Right] but ton : Click t hese b uttons to sele ct the p aramet ers. [Down] button[...]

EDN850H 27 4.4.2.1 LENS 1. When the SETUP menu is displayed on the screen, please direct the arr ow to point to “LENS” by using the UP and DOWN buttons. Press the SET button to adjust IRIS level (the higher is brighter). In most cases, you don’t need to adjust this, since Lens is Auto Iris supported. 2. Please press SET button for saving set [...]

EDN850H 28 Ö ESC: (Reserved). Ö Manual: (Reserved) 2. Press SET button when you finish all the settings. SETUP L E N S M A N U A L > S H U T T E R F L K W H I T E B A L . A T W B A C K L I G H T O F F A G C M I D D L E DNR LOW S E N S - U P _ _ _ SPECIAL <┘ EXIT BRIGHTNESS BRIGHTNESS |+++++++++| 25 SHU TTER > MANUAL 1/50 SETUP L E N S [...]

EDN850H 29 4.4.2.3 WHITE BALANCE Contr ol The screen color can be adjus ted by using the WHITE BALANCE function. 1. Please direct the arrow to point to “WHI TE BAL” on the SETUP menu by using the UP and DOWN buttons. 2. Please select the mode y ou would like to operat e by press ing the LEFT or RIGHT button. Please select one of the 3 modes bel[...]

EDN850H 30 4.4.2.4 BACKLIGHT Even there is a massive backlight behind the object, bright images of the background and the object can still be obtaine d by using the BACKLIGHT function. 1. Please direct the arrow to point to “BACKLIGHT” on th e SETUP menu by using the UP and DOWN buttons. 2. Select the mode you would like to o perate by pressing[...]

EDN850H 31 4.4.2.6 DNR (Dynamic Noise Reduction) Dynamic Noise Reduc tion in video images h as the following effects. 1. Images are brighter and sharper . 2. When the level of noise is redu ced, the perfor mance of a camera can appa rently be improved. 3. When it is recorded dig itally , reduced noise can reduce image file size. As the level of gai[...]

EDN850H 32 4.4.2.7 SENS-UP SENS UP is used to keep a bril liant, vivid screen ima ge by auto matically detect ing changes in the level of light und er low light level conditions. The value is from x2 ~x128. 1. Please direct the arrow to point to “S ENS UP” on the SETUP m enu by using the UP and DOWN buttons. 2. Select the mode you would like to[...]

EDN850H 33 4.4.2.8 SPECIAL 1. Please direct the arrow to point to “S PECIAL” on the SETUP menu by using the UP and DOWN buttons. 2. Select the mode you would like to o perate by pressing the LEFT or RIGHT button. 4.4.2.8.1 CAMERA ID Input the camera ID, and it will be appeared on the monitor . 1) Please direct the arrow to point to “CAMERA”[...]

EDN850H 34 6) If you would like to cancel the ID inputted, please move the cursor to “CLR”, and all th e letters in putted will be del eted. 7) Select “END” and press SET butt on to complete ID input. 4.4.2.8.2 COLOR ADJ Adjust the Color Gain from 0 ~ 15 C A M E R A I D A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j[...]

EDN850H 35 4.4.2.8.3 SYNC There are two SYNCHRONIZA TION modes: INTERNAL and EXTERNAL LINE-LOCK. In LINE-LOCK mode, without a synchronous generator , it synchronizes the video signal between came ras. The Line-Lock synchronization is only us ed in the pl aces of 60Hz (N TSC models) or 50H z (P AL models). -INT : Internal synchronization -LL: Extern[...]

EDN850H 36 z Please use the UP or DOWN button to move between T O P , DOWN, LEFT and RIGHT for adjusting the size of the area. z Please use the LEFT or RIGHT button to adjust the value for s ize of the area. z Additionally , it is possible to change t he position of the area. Please refer to the following e xampl e for de tailed steps o n moving AR[...]

EDN850H 37 3. Increase T OP scale value by 20. AREA1 position after chang e is: T O P: 30, DOWN: 45, LEFT : 20 and RIG HT : 40. 4. Increase RIGHT scale value by 20. AREA1 position af ter change is: T OP: 30, DOWN: 45, LEFT : 20 and RIG HT : 60. 5. Increase LEFT scale value by 20. AREA 1 position after change is: TOP: 30, DOWN: 45, LEFT : 40 and RIG[...]

EDN850H 38 z Please select the area y ou would like to cover from the 4 are as in AREA SEL mode . z Please select ON mode for the chosen area. z Please select A REA T O NE for cover area color . The smaller the nu mber , the darker the color . z Please use the UP or DOWN button to move between T O P , DOWN, LEFT and RIGHT for adjusting the size of [...]

EDN850H 39 1. The original position of A REA1 was TOP: 10, DOWN: 25, LEFT : 20 and RIGHT : 40. 2. Increase DOWN scale va lue by 20. AREA 1 position after change is: T O P: 10, DOWN: 45, LEFT : 20 and RIG HT : 40. 3. Increase T OP scale value by 20. AREA1 position after chang e is: T O P: 30, DOWN: 45, LEFT : 20 and RIG HT : 40. 4. Increase RIGHT sc[...]

EDN850H 40 5. Increase LEFT scale value by 20. AREA 1 position after change is: TOP: 30, DOWN: 45, LEFT : 40 and RIG HT : 60. z In order to save the changes and co mplete the setting, press the SET button. This allows you to return to the previous menu. 4.4.2.8.6 MIRROR -ON: Sets a horizontal image 180 angel inversion. -OFF: Disable the inversion. [...]

EDN850H 41 4.4.2.8.8 RESET Press the SET butt on on RESET for 3 seconds until it restarts. It will go to factory default value. 4.4.2.8.9 RETURN Press the SET butt on on RETURN. It saves all settings in SPECIAL menu and returns to the Setup menu. 4.4.2.9 EXIT Press the SET button on EXIT after you finish all the settings. I t will return to live im[...]

EDN850H 42 4.5 Audio The EDN850H camera can transmit audio to oth er clients using a built-in microphone or connecting to external microphone to pl ay audio received from other clients via connected speakers. This section describes how to configure the basic audio settings. Audio Check Enable Audio box to enable audio function. Audio Input: Audio f[...]

EDN850H 43 4.6 USER User Information Maximum 10 users can be set for using the IP camera. The user information displays the authorized users and acc ess levels: • Sup ervisor/Administrator –a supervisor/administrator has unrestricted access to the Setting menu and can determine the registration of all other users. However, administrator is not [...]

EDN850H 44 4.7 EVENT An event in the camera is when an Ev ent T y pe is activated and causes cert ain actions to be performed. The e vent type is the set of conditions that specifies how and when which actions will be performed. This table describes how to setup action types and event type. E v e n t T y p e Action Type Alarm Input Manual Trigger M[...]

EDN850H 45 4.7.1 Event The settings relating to e vent occurrences such as settings for the event occurrence, motion, alarm and time mask can be configure d on this page. The "Event” page has 4 tabs: [Event] tab, the [Motion] tab, the [Alar m] tab and the [Time Mask] tab. Press button to add an event condition. T o modify the event list, cli[...]

EDN850H 46 T o change the priority of events, click on the event and it will be highligh ted. Press or button to move bet ween events. The event that has highest priority will be activated first. Press Apply to apply the setting changes or Reset to res et without saving the change. This example describes how to set the camera to upload i mages to F[...]

EDN850H 47 5. Check “Enable Pre-alarm Buf fer” and “Enable Post-alar m Buf fer”. For pre-and post alarm buffer setting, please refer to “4.7.3 Al arm”. 6. Check “Enable This Event”. 7. Select “Always” for time mask. F or detail about T i me Mask, please refer to “4.7.4 T ime Mask”. 8. Click to save this event in event list. [...]

EDN850H 48 There are 5 motion trigger areas, which can be di stinguished by 5 different colors. Check Enable checkbox to enable event action. For each of them, you can set the event action to be activated. Event actio n can be set in “Event” s ection. Moreover , y ou can set the Sensitivity level for motion triggered by selecting from 1 (low), [...]

EDN850H 49 preceding the trigger . Input the desired length of pre-trigger buffer time. It can be set up to 120 seconds. Post-Alarm Buffer: Image saved internally in the server from the ti me immediately after the trigger . Input the desired length of post-trigger buffer tim e. It can be set up to 120 seconds. Press Apply to apply the setting chang[...]

EDN850H 50 Press button to add new time period. Mask name: Input a mask name for the new time period. Check the check box for the day to be scheduled: Sun, Mon, T ue, W ed, Thu, Fri & Sat. Set the S tart time and End time for time mask by cl icking Up arrow or Down arrow . Or simply press for a full day of event action. Press button to remove a[...]

EDN850H 51 4.8 SYSTEM Date/Time, Daylight Saving, SD card and Maintenance settings can be performed on this page. The "System " page has 4 t abs o f the [ Dat e/Time] tab, the [Da ylight Saving] tab, the [SD card] t ab and the [Mainten ance] tab. 4.8.1 Date/Time Machine Name Setting Machine Nam e: Enter the name of the camera. The ent ere[...]

EDN850H 52 previous month, > to go next month and >> to go next y ear . T i me: Click on Hour , Minute, Seconds, am/pm; then use up arrow to increase value and down arrow to decrease val ue. Press Apply to apply the setting changes or Reset to res et without saving the change. Set Date/T i me Sync. Check Enable NTP c heckbox to enable NTP [...]

EDN850H 53 4.8.2 Daylight Saving Set Daylight Saving Check Enable Daylight Saving checkbox to enable day light saving. Set the start time to daylight sav ing time. Set the start week of day light saving ti me: 1 st / 2 nd / 3 rd / 4 th / Last Set the start date of daylight saving time: S unday / Monday / T uesday / W ednesday / Thursday / F riday /[...]

EDN850H 54 Press Apply to apply the setting changes or Reset to res et without saving the change. 4.8.3 SD Card Setup SD Card Notification: Notification will be made via e- mail when the remaining space of the SD memo ry card re ached the va lue selected from the following. 50%, 20%, 10%, 5%, 2%, 0% Event Recording: FTP backup only: Event video wil[...]

EDN850H 55 Normal: Follow the event actions settings you have made in “Event” menu to record event video to SD c ard. Overwrite : Select ON for overwriting data when SD card memory is full. Select OFF for not overwriting SD card data. Press Apply to apply the setting changes or Reset to res et without saving the change. SD Card Utility The tota[...]

EDN850H 56 4.8.4 Maintenance Maint enance Se rver Reboot: The unit is rebooted without changing any of the settings. Use this method by pressing Reboot button if the unit is no t behaving as expected. Restore: The unit is restarted and most current settings are reset to the factory defaul t values by press ing Restore button. The only settings save[...]

EDN850H 57 the Load button. Th e settings will be restored to the previous configuration. Upgrade Firmware Upgrade the EDN850H with the lates t firmware. Press Browse button to s earch firmware file. Press Upgrade button to upg rade the firmware. Note 1: Do not disconnect power to the unit during the upgrade. The unit r eboots automatically after t[...]

EDN850H 58 5. SPECIFICA TIONS CAMERA Pickup Device 1/3" Sony Super HAD I nterlaced CCD Picture Elements NTSC: 768 (H) x 494 (V); P AL: 752 (H) x 582 (V) Sensitivity 0.002 Lux (SENS-UP 128x); 0.25 Lux/F=1.2 Day & Night Y es (with IR cut filter) Lens V ari-Focal Lens with Auto Iris (2.8~1 0mm) Video Ou tput BNC socket, composite 1 V p -p / 7[...]

EDN850H 59 PHYSI CAL Weight 0.74 kg / 1.6 lbs Dimensions 123mm (O.D.) x 107.8mm (H) ; 4.8” (O.D.) x 4.2” (H) ENVIRONMENT AL Operating T emp. -1 0°C ~50°C / 14°F~122 °F Humidity (20%~80% Humidity) OTHE RS W aterproof IP66 V andal Resist ant Y es[...]

EDN850H 60 EverFocus Electronics Corp. Head Office: 12F , No.79 Sec. 1 Shin-T ai W u Road, Hsi-Chi, T aipei, T aiwan TEL: 886-2-26982334 F AX: 886-2-26982380 www .everfocus.com.tw USA Office: 1801 Highland A ve. Unit A Duarte, CA 91010, U.S .A. TEL: +1-626-844-8888 F AX: +1-626-844-8838 www .everfocus.com USA N.Y . Office: 415 Oser A venue Un it S [...]