Exmark VH3615KA Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Exmark VH3615KA an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Exmark VH3615KA, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Exmark VH3615KA die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Exmark VH3615KA. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Exmark VH3615KA sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Exmark VH3615KA
- Den Namen des Produzenten und das Produktionsjahr des Geräts Exmark VH3615KA
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Exmark VH3615KA
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Exmark VH3615KA zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Exmark VH3615KA und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Exmark finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Exmark VH3615KA zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Exmark VH3615KA, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Exmark VH3615KA widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    [...]

  • Seite 2

    ii WA RNING The engine exhaust f rom this pr oduct contains chemicals k nown to the St at e of Califor nia t o cause cancer , birth def ect s , or other r epr oduct ive harm. IMPORTANT W hen the m ower is used or operat ed on any California f or est , brush or gr ass covered land, a work ing spark ar r est er m ust be attached to t he m uf fler. If[...]

  • Seite 3

    iii EXMARK PA RTS PLUS     PROGRA M EFFECTIVE DATE: September 1, 1995 Program If your Ex mark dealer does not have the Exmark part in stock, Exmark w ill get the parts to the dealer the next business day or the part will be FREE* Guaranteed!! How the Program Works 1. If dealer does not have part in stock for a "dow n" unit at [...]

  • Seite 4

    iv CONGRAT ULATIONS on the purchase of your Exmark Mower. This product has been caref ully designed and manuf actured to g ive y ou a m aximum amount of dependability and years of trouble-f ree operation. OPERA TOR'S M ANUA L This manual cont ains assem bly, oper at ing , maintenance, adj ustment and saf ety instructions f or your Exmark m owe[...]

  • Seite 5

    TABLE OF C ONTENTS v 1. SA FETY ................................................................................................... PA GE 1.1 Sa f ety Alert Sy mbol ...................................................................................... 1 1.2 Trai ning ..................................................................................[...]

  • Seite 6

    - 1 - 1. SA FETY 1.1 SA FETY A LERT SYMBOL THI S SAFETY ALERT SY MBO L IS US ED BOT H IN TH IS MA NU A L A ND ON THE MA CHINE TO I DENTIFY IMPORTA NT SA FETY MESSA G ES W HICH MUST BE FOLLOW ED TO AVOID A CCIDENTS. THIS SYM BO L MEA NS: A TTENTION! BECOME A LERT! YOUR SA FETY IS INVOLVED! The saf ety alert symbol appear s above infor mation which a[...]

  • Seite 7

    - 2 - WA RNING POTENT IAL HAZARD ♦ Engine exhaust contains carbon m onoxide, which is an odorless deadly poison. W HAT CAN HAPPEN ♦ Carbon monoxide can kill you and is also known to t he State of California t o cause bir t h def ects. HOW T O AVOI D T HE HAZARD ♦ Do not run eng ine indoor s or in a sm all confined area where dangerous carbon [...]

  • Seite 8

    - 3 - DA NGER POTENT IAL HAZARD ♦ In certain condit ions gasoline is extremely flam m able and highly explosive. W HAT CAN HAPPEN ♦ A static charg e can ignite g asoline vapors. A f ire or explosion from g asoline can burn you, others, and cause property damag e. HOW T O AVOI D T HE HAZARD ♦ Purchase and store g asoline only in an approved co[...]

  • Seite 9

    - 4 - 1.4.5 Stop the blades when crossing surf aces other than g r ass; and w hen transport ing t he mower to and from t he ar ea t o be mowed. 1.4.6 Never operate the mower with defect iv e g uards, shields, or covers. Alw ays have safety shields, guards, switches, and other devices in place and in proper working condit ion. 1.4.7 Do Not chang e t[...]

  • Seite 10

    - 5 - 1.5.5 Keep the mower and fuel cont ainer in locked storag e to prevent children f r om playing or tam per ing with them. 1.5.6 Gasoline powered equipment or fuel containers should not be stored in a basement or any enclosed area, where open pilot lig hts or heat appliances are present. 1.5.7 Max imum mowing result s and saf ety can only be ac[...]

  • Seite 11

    - 6 - PART NO. 323741 LOCATI ON: Console PART NO. 323691 LOCATION: RH Side of Console PART NO. 303517 LOCATI ON: Left Side of Rear Surface on Engine Dec k PART NO. 403143 LOCATI ON: Right Side of Rear Surface on Engine Dec k PART NO. 413214 LOCATI ON: Right Side of Hydro Control Crank Arm PART NO. 603845 LOCATIO N: Rear Center of T op Surface of En[...]

  • Seite 12

    - 7 - 2. SPECIFICA TIONS 2.1 MODEL NUMBE R: Serial Nos. 220, 000 & Hi gher: VH3615KA; VH4815KA 2.2 ENGINE 2.2.1 Engine Specif icat ions: See your Engine Owner's Manual. 2.2.2 3600 RPM (No Load). 2.3 FUEL SYSTEM 2.3.1 Capacity: 5.0 gal. (18.9 L.) 2.3.2 Type of Fuel: Regular unleaded g asoline, 87 oct ane or higher. I n countries using the r[...]

  • Seite 13

    - 8 - 2.6.2 Hydraulic Filter is replaceable cart ridge type. P/N 513211: 10 microns, 18 psi bypass (Summer use above 32 ° F) P/N 523541: 40 microns, 18 psi bypass (W inter use below 32 ° F) 2.6.3 Speed Range: Forward 0 - 6. 2 m ph ( 10.0 km/ h) Reverse 0 - 2.2 mph ( 3. 5 k m/h) 2.7 WHEEL DRIVE SY STEM: Drive wheels are direct coupled to Park er/R[...]

  • Seite 14

    - 9 - 2.11 TORQUE REQUIREMENTS BOLT LO CATION TORQ UE Blade/Cu tter Housing Spindle B olt ................................. 75-80 ft-lbs. Caster Bracket M ounts .................................................. 30-35 f t-lbs. Cutter De ck /Engine De ck M ount .................................... 30-35 ft-lbs. Engine M ounting Bolts (Kohler & K[...]

  • Seite 15

    - 10 - b) Loosen clamp on eng ine control plate (See Fig ure 2). Att ach inner wire of the throt tle cable to the contr ol plat e lever and posit ion cable under cable clamp, do not t ig hten clamp. FIG 2 15 HP KA WASA KI SPEED CONTROL (THROTTLE CA BLE HOO K- UP) c) Pull the cable to the r ight when facing t he control plate until t he alignment ho[...]

  • Seite 16

    - 11 - 3.13 Install the speed cont rol rod assembly (linka g e wi th the yoke inst alled on one end) into the end of the speed control lever located under neat h t he cent er of t he console. Insert t he end of the link age (opposite t he yok e) int o t he end of the speed control lever f rom the rig ht hand side and f asten with a hairpin cotter f[...]

  • Seite 17

    - 12 - 4. OPERA TION INSTRUCTIONS 4.1 Controls 4.1.1 Operator Pr esence Control (OPC) Levers: Locat ed on the upper handle assembly directly above the handle grips. When these l evers are depressed, the OPC system senses that t he operat or i s i n t he normal operat or's position. When the levers are released, the O PC system senses t hat the[...]

  • Seite 18

    - 13 - Once the eng ine has st ar t ed, move the throt t le cont r ol lever t o t he m idway point and allow the engine to warm- up bef ore going to f ull t hr ottle. 4.1.7 “Of f-Run” Switch: Locat ed on t he console. Turn k ey to the “Run” position to allow the engine to be star t ed. Turn k ey to t he “ O f f” posit ion to shut engine[...]

  • Seite 19

    - 14 - 4.2.1 Fill fuel t ank . For best r esult s use only clean f resh regular g rade unleaded gasoline with an octane rat ing of 87 or hig her . Regular g rade leaded gasoline may also be used; however, combustion chamber and cylinder head will requir e m or e f requent ser vice. See Eng ine Owner's Manual. Do not add oil to g a soline. DA N[...]

  • Seite 20

    - 15 - WA RNING POTENT IAL HAZARD ♦ Engine exhaust contains carbon m onoxide, which is an odorless deadly poison. W HAT CAN HAPPEN ♦ Carbon monoxide can kill you and is also known to t he State of California t o cause bir t h def ects. HOW T O AVOI D T HE HAZARD ♦ Do not run eng ine indoor s or in a sm all confined area where dangerous carbon[...]

  • Seite 21

    - 16 - CA UTION POTENT IAL HAZARD ♦ If t he neut ral lock latches ar e not completely engag ed t he drive levers could unexpectedly slip into the for ward drive position. W HAT CAN HAPPEN ♦ If t he drive levers slip into the drive position, t he unit could lurch f or ward and cause injur y or property damage. HOW T O AVOI D T HE HAZARD ♦ Be s[...]

  • Seite 22

    - 17 - 4.3.8 Blade Disengagem ent : Push forward and down completely on the eng ag ement knob to diseng age the blades (See Section 4. 1.5). 4.4 TRA NSPORTING WA RNING POTENT IAL HAZARD ♦ Loading the m ower onto a t r ailer wi t hout strong enough or pr oper ly supported r amps could be dangerous. W HAT CAN HAPPEN ♦ The ram ps could collapse ca[...]

  • Seite 23

    - 18 - 5.1 PERIODIC MA INTENA NCE 5.1.1 Check eng ine oil level. Serv ice Interv al: See Engine Ow ner's Manual a) Make sure engine is st opped and on a level surf ace. b) Check with engine cool. c) Clean area around dipstick. Remove dipstick and wi pe oil off . Reinsert the dipstick ( DO NOT screw into place). Rem ove dipstick and check oil l[...]

  • Seite 24

    - 19 - h) Remove jack st ands ( or eq uivalent support) and lower deck t o g round. FIG. 6 BLA DE BOLT IN STA LLA T ION 5.1.4 Check saf et y interlock system. Serv ice Interv al: Daily a) For your saf et y, your Exmark mower is equipped with Operat or Pr esence Controls (O PC) . W hen either t he mower blades are engaged, or the speed control lever[...]

  • Seite 25

    - 20 - d) Remove the oil drain plug from t he r ight hand side of the engine. Allow oil to drain, t hen replace drain plug. e) Replace the oil f ilter as per Eng ine O wner's Manual. Clean around oil filt er and unscr ew filter to r em ove. Before r einst alling new filter , apply a thin coating of oil on the surf ace of the r ubber seal. Turn[...]

  • Seite 26

    - 21 - e) Loosen f ilt er 1/2 turn and allow a small amount of oil to leak f rom the oil filt er ( this allows air to be purged f rom the oil f ilter and supply hose f r om the hydraulic reservoir). Turn f ilt er clockwise until rubber seal cont act s t he filt er adapt er. Then t ig hten the f ilt er an additional 2/3 to 3/4 t ur n. f) Raise the r[...]

  • Seite 27

    - 22 - e) To “pr ime” charge pump, loosen t wo hex socket head capscrews (shown in Figure 7) 1-1/2 turns only. Make sure engine is not runni ng. Lift charge pum p housing upward and w ait f or a steady f low of oil t o f low out fr om under housing . Retighten capscrew s . Do this for bot h pum ps. Note: Hydraulic reser voir can be pr essur ize[...]

  • Seite 28

    - 23 - No. 4 Idler Pivot ( Pump Drive) Located Under Eng ine Deck No. 4 & 6 (Idler Pivots) Disassemble and grease once a month under a “ No Load” condit ion. c) Lubricate pivot points with a spray penetrating lubricant as directed below. SPRA Y LUBRICA NT CHART PIVOT POINT NO. OF P LACES 36” 48 ” SERVICE INTERVAL 1. Blade Engag ement Up[...]

  • Seite 29

    - 24 - c) OPC lever setscrew s. d) Shoulder bolts in ends of speed control crank . e) Between the fuel t ank studs and the f uel tanks. f) Betw een t he shifter lever and t he k nob. Adhesives such as “Loctite RC/609 or RC/ 680” or “Fel-Pro Pro- Lock Retaining I or Retaining II” ar e used on t he f ollowing: a) OPC lever hubs and cross-shaf[...]

  • Seite 30

    - 25 - 5.2.1 Blade Spacers: Blades may be adjusted f or cutting heig ht by using the f our 1/ 4" spacer s found on the blade spindle bolts (f actory setting is two above and tw o below). T his allows a 1" range in 1/4" incr em ent s of cutt ing height in any axle position. The same number of blade spacers must be used on all blades t[...]

  • Seite 31

    - 26 - FIG. 8 A XLE and CAST ER HEI G HT A DJUSTMENT Refer t o t he following chart t o pr operly adjust desired cutt ing height. CUTTING HEIGHT A DJUS TME NT (1" to 4 1/4") AX L E POSITIO N (FIG. 9) NO. OF S PA CERS BELOW CAST ER 1/2" 3/16" NUMBER OF 1/ 4” BLADE SPA CERS BELOW SPI NDLE 4 3 2 1 0 A 0 0 1" 1 1/4" 1 1/[...]

  • Seite 32

    - 27 - b) W ith blade drive engag ed (lever pulled up, adjust t he link age lengt h to where the lower end of the bellcrank just clears t he axle support g usset (See Figure 9) . Make sur e t he assist ar m is against the r ear assist arm stop on the deck ( See Fig ure 10). Push the lever down to the diseng ag ed position. T he assist ar m should c[...]

  • Seite 33

    - 28 - FIG. 10 CUTTER DECK BELT ADJUSTMENT e) Proper belt t ension will require about 10 lbs. side pull on belt , halfway between pulleys, to deflect belt 1/2”. (See Fig ure 10, Point A). 5.2.6 Blade Brake Adj ust ment: a) Stop eng ine and r em ove spark plug wire(s). b) Disengag e the blades. c) Make sure the blade brake pad r est s ag ainst the[...]

  • Seite 34

    - 29 - Note: T hese dr awings ar e viewed from under neat h t he engine deck FIG. 12 FIG. 13 36" B ELT GUIDE LOC A TION 48" B ELT GUIDE LOC A TION 5.2.8 Pump Drive Belt Tension Adj ustment: No adjustment necessary . 5.2.9 Hydro Drive Linkage Adj u st m ent : a) Adjust Speed Cont rol Linkag e and neut r al saf ety switch 1. Move the speed [...]

  • Seite 35

    - 30 - Make sure you have not reached the end of t he neutral lock lat ch slot . If you have, short en t he dr ive lever link ag e. If the wheel turns while holding the dr ive lever in neutr al, the neutral contr o l link ages need to be adjusted. I f wheel stop then go to st ep 7. FIG. 15 HYDRO DRIVE LI NKAGE A DJUSTMENT 4. Loosen the nut against [...]

  • Seite 36

    - 31 - Aft er adj usting the lef t hydro control link a g e, move the speed control lever to the mid-speed posit ion and then back to t he neut ral position. Recheck the lef t drive wheel rotation to see if fur t her adjustment is necessary - be sure the speed cont r ol lever is in t he neut r al position. If inconsi st ent neut ral occurs, check t[...]

  • Seite 37

    - 32 - 4. If the unit tr ack s to one side or the ot her , t ur n the quick t rack k nob . Turn t he k nob right t o “ s t eer ” right, t u r n t he k nob left t o “ s t eer ” left. 5.2.10 Hydro Pump Spr ing Tension Setting : a) For medium or heavy duty drive conditions such as operation with a sulky on steep slopes, a hig her spr ing force[...]

  • Seite 38

    - 33 - e) Check t hat there is f uel in t he t ank and that t he f uel valve is open. f) Check that t he spark plug wire(s) ar e pr oper ly connected. g) Check f or loose or f aulty w iring connections. I f it is necessary to disconnect wire connectors, Do Not pull on t he wi r es while disconnecting. h) Check f or corrosion at all wiring connect i[...]

  • Seite 39

    - 34 - 8. WIRING DIA GRAM[...]

  • Seite 40

    - 35 - 9. HYDRA ULIC DIAGRA M[...]

  • Seite 41

    - 36 - 10. WA RRANTY Limited W arranty Exmark Comm ercial Turf Equipment Exmar k Mfg. Co. Inc. ("Exmar k ") warrants on the ter m s and condit ions her ein, t hat it will repair, replace or adj ust any part manuf act ur ed by Exmark and found by Exmark( in t he exercise of its reasonable discretion) to be defect ive in f act or y material[...]

  • Seite 42

    - 37 - As a condition to this warrant y, cust om er shall have read t he oper at or's manual and shall have returned t o Exmark , within the prescribed time, the enclosed warranty registrat ion car d. The sole liability of Exmar k with respect to this warrant y shall be repair and r eplacem ent as set for t h her ein. Exmark shall have no liab[...]

  • Seite 43

    - 38 - T H I S I S A 1 5 ° S L O P E T H I S I S A 1 0 ° S L O P E T H I S I S A 5 ° S L O P E ALIGN THIS EDGE WITH A VERTICAL SURF ACE (TREE, BUILDING, F E NCE POST , POLE ETC.) EXAMPLE: COMP ARE SLOPE WITH FOLDED EDGE. FOLD ALONG APP ROPRIA TE LINE T HI S I S A 2 0 ° S L O P E[...]

  • Seite 44

    SEE EXMARK’S COMPLETE LINE OF PRODUCTS FOR TURF CARE LAZER Z ™ LAZER Z ™ HP TURF RANGER ® TURF TRACER ® TURF TRACER ® HP VIKING HYDRO METRO ™ METRO ™ HP SELF STEERIN G SULKY GRASS CATCHER MICRO-MULCH ™ ACCESS ORY ® MFG. C O. I NC. ©1997,1998, 1999 PA RT NO. 850654 EXMARK MFG. CO . INC. (402) 223-6300 INDUSTRIAL PA RK BOX 808 FA X ([...]