Ford 2008 F-250 Bedienungsanleitung

Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 18 Entertainment Systems 22 AM/FM stereo 22 AM/FM stereo with CD 24 AM/FM stereo with in-dash six CD 30 Auxiliary input jack 36 Satellite radio information 40 Navigation system 43 Family entertainment system 43 Climate Controls 71 Heater only 71 Manual heating and air conditi[...]

Locks and Security 136 Keys 136 Locks 136 Anti-theft system 148 Seating and Safety Restraints 151 Seating 151 Safety restraints 158 Airbags 171 Child restraints 180 Tires, Wheels and Loading 192 T ire information 195 T ire inflation 196 V ehicle loading 212 T railer towing 219 T railer brake controller -integrated 223 Recreational towing 230 Drivin[...]

Customer Assistance 298 Reporting safety defects (U.S. only) 304 Reporting safety defects (Canada only) 305 Cleaning 306 Maintenance and Specifications 314 Hood 315 Engine compartment 316 Engine oil 319 Battery 322 Engine coolant 324 Fuel information 330 Air filter(s) 349 Part numbers 350 Maintenance product specifications and capacities 352 Access[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. W arning symbols on your vehicle When you see this symbol, i[...]

SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide. Service Data Recording Service data recorders in your vehicle are capable of collecting and s[...]

V ehicle Modification Data Recording Some aftermarket products may cause severe engine and/or transmission damage; refer to the What is not covered section in The new vehicle limited warranty for your vehicle chapter of your vehicle’ s W arranty Guide for more information. Some vehicles are equipped with Powertrain Control Systems that can detect[...]

Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to the driving t[...]

If your vehicle is equipped with the Ford Ambulance Preparation Package, it will be indicated on the Safety Compliance Certification Label. The label is located on the driver’ s side door pillar or on the rear edge of the driver’ s door . Y ou can determine whether the ambulance manufacturer followed Ford’ s recommendations by directly contac[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid - Non-Petroleum Based Parking Aid System Stability Control System[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Flu[...]

W ARNING LIGHTS AND CHIMES V ehicles equipped with a manual transmission V ehicles equipped with an automatic transmission W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many light[...]

bulbs work. If any light remains on after starting the vehicle, refer to the respective system warning light description for additional information. Note: Some W arning Lights are reconfigurable telltale (RTT) indicator lights and will illuminate in the Message Center Display and function the same as the warning light. Check engine: The Check engin[...]

Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately by your authorized dealer . Normal braking is still functional unless the brake warning light also is illuminated. Airbag readiness: If this light fails to illuminate when ignition is turned to RUN,[...]

T raction control (R TT) (if equipped): Displays when the T raction Control 娂 system is active. If the light remains on, have the system serviced immediately by your authorized dealer . Refer to T raction control in the Driving chapter for more information Check fuel cap (R TT): Displays when the fuel cap may not be properly installed. Continued [...]

T ransmission T ow/Haul Feature (automatic transmission) (if equipped): The T ow Haul light remains illuminated as long as the T ow/Haul feature is activated. Refer to the Driving chapter for transmission function and operation. If the light remains illuminated and will not cancel using the T ow/Haul switch located on the end of the gear shift leve[...]

Diesel warning lights: • Glow plug pre-heat • W ater in fuel • Low oil pressure Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF , LOCK or ACCESSOR Y position and the driver’ s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is n[...]

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the e[...]

Odometer: Registers the total miles (kilometers) of the vehicle. Refer to Standard message center or Optional message center in the Driver Controls chapter on how to switch the display from Metric to English. T rip odometer: Registers the miles (kilometers) of individual journeys. If equipped with a one button message center (Select/Reset), press a[...]

Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the RUN position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The FUEL icon and arrow indicates which side of the vehicle the fuel filler door is located. Refer to Filling the tank in the Maintenance and Specificati[...]

Altering the severity of the driving conditions is recommended to lower the transmission temperature into the normal range. Red area (over temperature) — the transmission fluid is overheating. Stop the vehicle to allow the temperature to return to normal range. If the gauge is operating in the Y ellow or Red area, stop the vehicle and verify the [...]

AUDIO SYSTEMS AM/FM stereo system (if equipped) The AM/FM stereo system does not contain rear speakers; only front driver side and passenger side speakers. Accessory delay: Y our vehicle is equipped with accessory delay . With this feature, the window switches and radio may be used for up to ten minutes after the ignition is turned off or until eit[...]

BASS (Bass): Press AUDIO to reach the bass setting. Use / / SEEK . BAL (Balance): Press AUDIO to reach the balance setting. Use / / SEEK to adjust between the left and right speakers. Setting the clock: Press and hold CLK until the hours start to flash, then use / / SEEK to adjust. T o adjust minutes, press CLK again to make the minutes start to fl[...]

AM/FM stereo single CD/satellite compatible sound system (if equipped) Accessory delay: Y our vehicle is equipped with accessory delay which allows you to operate the window switches and the audio for up to ten minutes after the ignition has been turned off or until either front door is opened. 1. / : Press / to manually go up or down the radio fre[...]

3. MENU: Press MENU repeatedly to access to the following settings: CA TEGOR Y (satellite radio if equipped): : Press MENU until the currently active category appears in the display (CA TEGORY MODE). In CA TEGORY MODE, press / to scroll through the list of available SIRIUS channel Categories (Pop, Rock, News, etc.) Press SEEK, SEEK or SCAN to selec[...]

F ADE: Press MENU to reach the fade setting. Use / / SEEK, SEEK to adjust the audio between the back (B) and front (F) speakers. SPEEDVOL (Speed sensitive volume, if equipped): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louder with increasing vehicle speed to compensate for road and wind noise. Use / / SEEK, SEEK to a[...]

5. SEEK: In radio mode, press / to access the previous/next strong station. In CD/MP3 mode, press / to access the previous/next CD/MP3 track. In satellite radio mode (if equipped), press SEEK, SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.), press SEEK, SEEK to seek to the previous/next channe[...]

9. FOLDER: In folder mode, press FOLDER to access the previous folder on MP3 discs, if available. 10. FF (Fast forward): Press FF to manually advance in a CD/MP3 track. 11. REW (Rewind): Press REW to manually reverse in a CD/MP3 track. 12. Memory presets: T o set a station: Select frequency band AM/FM1/FM2; tune to a station, press and hold a prese[...]

In satellite radio mode (if equipped), press and hold to hear a brief sampling of the next channels. Press again to stop. In CA TEGORY MODE, press SCAN to hear a brief sampling of the channels in the selected category . Press again to stop. Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer f[...]

Premium/Audiophile in-dash six CD/MP3/satellite compatible sound system (if equipped) Accessory delay: Y our vehicle is equipped with accessory delay which allows you to operate the window switches and audio for up to ten minutes after the ignition has turned off or until either front door has opened. 1. / (T une/Disc selector): In radio mode, pres[...]

3. MENU: Press repeatedly to access to the following settings: CA TEGOR Y (satellite radio if equipped): Press MENU until the currently active category appears in the display (CA TEGORY MODE). In CA TEGORY MODE, press / to scroll through the list of available Sirius channel Categories (Pop, Rock, News, etc.) Press SEEK or SCAN to select the categor[...]

T o view the station name or type: When the desired category appears in the display , press TEXT/SCAN to toggle between displaying the station type (COUNTRY , ROCK, etc.) or the station name (WYCD, WXYZ, etc.). BASS: Press MENU to reach the bass setting. Use / / SEEK, SEEK to adjust. TREB (T reble): Press MENU to reach the treble setting. Use / / S[...]

COMPRESS (Compression): A vailable only in CD/MP3 mode. Press MENU until COMPRESS ON/OFF appears in the display . Use / / SEEK, SEEK to toggle ON/OFF . When COMPRESS is ON, the system will bring soft and loud CD passages together for a more consistent listening level. 4. AUX: Press repeatedly to cycle through FES/DVD (if equipped), LINE IN (Auxilia[...]

7. SHUFFLE: In CD/MP3 mode, press SHUFFLE to engage shuffle mode. SHUFFLE ON will appear in the display . If you wish to engage shuffle mode right away , press SEEK to begin random play . Otherwise, random play will begin when the current track is finished playing. CD SHUF will appear in the display . T o disengage, press SHUFFLE again. SHUFFLE OFF[...]

In CD/MP3 mode, press and release to display track title, artist name, and disc title and file name (if available). In satellite radio mode (if equipped), press and release to enter TEXT MODE and display the current song title. While in TEXT MODE, press again to scroll through the current song title, artist, channel category and the SIRIUS long cha[...]

discs, one at a time, label side up, when prompted. Once loaded, the disc in the last slot loaded will begin to play . Note: An MP3 disc with folders will show F001 (folder #) T001 (track #) in the display . An MP3 disc without folders will show T001 (track#) in the display . Refer to MP3 folder structure later in this chapter for further informati[...]

2. Ensure that the battery in your portable music player is new or fully charged and that the device is turned off. 3. Attach one end of the audio extension cable to the headphone output of your player and the other end of the audio extension cable to the AIJ in your vehicle. 4. T urn the radio on, using either a tuned FM station or a CD loaded int[...]

GENERAL AUDIO INFORMATION Radio frequencies AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz Radio reception factors There are three factors that can affect rad[...]

incompatibility , certain homemade compact discs may not function correctly when used in Ford CD players. Do not use any irregular shaped CDs or discs with a scratch protection film attached. CDs with homemade paper (adhesive) labels should not be inserted into the CD player as the label may peel and cause the CD to become jammed. It is recommended[...]

Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extension will be played. Other files will be ignored by the system. This enables you to use the same MP3 d[...]

Satellite radio reception factors: T o receive the satellite signal, your vehicle has been equipped with a satellite radio antenna located on the roof of your vehicle. The vehicle roof provides the best location for an unobstructed, open view of the sky , a requirement of a satellite radio system. Like AM/FM, there are several factors that can affe[...]

Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly . SA T F AUL T Internal module or system failure present. If this message does not clear within a short period of time, or with an ignition key cycle, your receiv[...]

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly . NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly . NO SIGNAL Loss of sign[...]

and to plug in and play a variety of standard video game systems. The DVD player is capable of playing standard DVDs, CDs, MP3s and is compatible with CD-R/W , CD-R and certain CD-ROM media. Please review this material to become familiar with the FES features and controls as well as the very important safety information. Quick start Y our Family En[...]

T o play a CD in the DVD system: The DVD system can play audio CDs, CD-R and CD-R/W , CD-ROM and video CDs. T o ensure proper disc operation, check the disc for finger prints and scratches. Clean the disc with a soft cloth, wiping from the center to the edge. 1. Ensure that the vehicle ignition is in the RUN or ACCESSORY position. 2. Insert a CD in[...]

T o play an auxiliary source through the DVD system The DVD system can be used to connect and play auxiliary electronic devices such as game systems, personal camcorders, video cassette recorders, etc. 1. Ensure that the vehicle ignition is in the RUN or ACCESSORY position. 2. Press the power button to turn the DVD system on. The indicator light ne[...]

A green light will illuminate next to either the A or B Headphone Control Button to indicate which channel is active (able to be controlled). 3. Press MEDIA to change the audio source of the active channel (A or B). The audio source will be shown on the display . Y ou may change the active channel by pressing the A or B headphone control button. No[...]

DVD player controls 1. Headphone control A/B: Press to select either the A or B headphone source. Then press MEDIA to select the desired playing media for that headset. When a headphone channel has been selected (A or B), selections will affect the source on that channel only . Note: Headphone A can access any possible media (AM, FM1, FM2, SA T (if[...]

4. (Fast forward): Press and release for the next chapter or track. Press and hold to forward search a DVD, Video CD, or FES CD in DVD/CD mode. 5. / (Play/Pause): Press (Play) to select DVD mode (and to turn the DVD system on if it is off). If a disc is present, it will resume or begin to play . Press (Pause) while playing a disc to pause a DVD or [...]

Single Play (same media playing through all speakers). For further interaction information, refer to Single Play/Dual play . 12. MEDIA: Press repeatedly to select from the various possible playing media sources (AM, FM1, FM2, SA T (if equipped), CD, DVD, DVD-AUX). The media will show in the status display on the top of the screen when in Dual Play [...]

1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF . 2. Cursor controls: Use in various active menus to advance the cursor up/down/left/right. When not in a Menu, the left and right cursor controls decrease and increase the display brightness. 3. DISPLA Y : Press to access the on-screen display of the FES functions and adj[...]

(W ireless headphone volume is controlled with the rotary dial on the right ear piece.) 8. Fast Forward/Next: In DVD mode, press and hold for a quick advance within the DVD. Press and release to advance to the next chapter . In CD/MP3 mode, press to access the next track. 9. Play/Pause: Press to play or pause a DVD. 10. SHUFFLE: Press to play all t[...]

Battery replacement Batteries are supplied with the remote control unit. Since all batteries have a limited shelf life, replace them when the unit fails to control the DVD player . Remove the screw and unlatch the battery cover to access the batteries. The remote control unit uses two AAA batteries which are supplied with the unit. 2008 F-250/350/4[...]

Headphones Wireless headphones Y our FES system is equipped with two sets of battery powered, infrared wireless headphones. T wo AAA batteries are needed to operate the headphones. (Batteries are included.) Additional infrared wireless headphones may be purchased for use with the system. Also, wired headphones may be purchased and plugged in where [...]

T o install the batteries, remove the screw at the bottom of the cover . Then, lightly press down on top and slide the cover off. When replacing the batteries, use two new batteries (alkaline recommended) and install them with the correct orientation as indicated in the battery housing. 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA [...]

T o operate the headphones: • Press POWER on the ear piece to turn on the headphones. A red indicator light will illuminate indicating the headphones are ON. Press POWER again to turn the headphones off. • Adjust the headphones to comfortably fit your head using the headband adjustment. • Select the desired audio source (Channel A or B) for e[...]

Wired headphones Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may become entangled in the cords and seriously injure themselves. Y ou may purchase wired headphones for your FES (Family Entertainment System). Plug them into t[...]

over headphones while the front speakers play the chosen selection for the front audio system, they may listen to another over the headphones. DUAL PLA Y will appear in the radio display . When both the front seat passengers and the rear seat passengers listen to the same audio source, SHARED MODE will appear on the radio. Note: If the front seat p[...]

While operating in Headphone Only Mode, the system will have limited functionality . • The system will only output audio to the headphones. It will not be capable of providing audio to the speakers. • The available sources in FES Headphone Only Mode are DVD-DISC and DVD-AUX, regardless of headphone channel (A or B). • When a disc is inserted [...]

Aspect ratio Select ASPECT RA TIO to select the viewing size and shape of the video displayed on the LCD screen. This is disc dependent. Y ou can select from: WIDE, LETTER BOX or P AN SCAN. Once you have made your selection, press ENTER to confirm. The LCD screen display will immediately change to your selection after the system resumes playback of[...]

Subtitles Select SUBTITLES to turn the subtitle option on or off. The system default is OFF . Once you have made your selection, press ENTER to confirm. This is disc dependent. Audio CDs T o play audio CDs on your DVD system: 1. Ensure that the vehicle ignition is in the RUN or ACCESSORY position. 2. Ensure that the DVD system is ON. 3. Insert an a[...]

SCAN: Press for a brief sampling of all tracks on the current CD. Press again to stop. Playing MP3 discs T o play an MP3 disc on your DVD system: 1. Ensure that the vehicle ignition is in the RUN or ACCESSORY position. 2. Ensure that the DVD system is ON. 3. Insert the MP3 disc into the DVD system, label side up. 4. The folder , track and elapsed t[...]

effect on sound quality and are recommended only for speech or low fidelity music material. W e recommend that you encode MP3 files using a high quality encoder . • PC configuration — Encoding MP3 files requires intensive use of your computer’ s resources. Follow the PC configuration recommendations of the encoder software vendor . W e recomm[...]

Playing a DVD 1. Ensure that the vehicle ignition is in the RUN or ACCESSORY position. 2. Ensure that the navigation system is on. 3. Insert a DVD label-side up into the system. 4. Use the DVD bezel controls to: Press to play or pause a DVD. Press to stop or eject a DVD. Press and release to go to the previous chapter . Press and hold for a fast re[...]

Frame by frame 1. W ith a DVD playing, press pause. 2. Press the right cursor button. The DVD will advance one frame. Each press of the right cursor button will advance the DVD video by one frame. Headphone/auxiliary jacks There are wired headphones (not included) and auxiliary jacks on the left and right side of your DVD system. They can be used t[...]

The B headphone jack (5) is located on the right side of the DVD system. Plug in wired headphones (not included) here. Note: The B headphones can only access DVD and AUX modes. They cannot access radio sources. Audio displays Y our DVD system interacts closely with the front audio system. Status messages will appear in the radio display showing the[...]

FULL (enabled): The FES has control over the primary (speaker) and secondary (headphone) audio sources. LOCAL : The FES has control over the secondary source (headphones) only . The radio will ignore button presses that affect the primary (speaker) audio source. LOCKED (disabled): The FES buttons are locked and all FES button presses are ignored by[...]

Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may become entangled in the cords and seriously injure themselves. The front glass on the liquid crystal display (LCD) flip-down screen may break when hit with a hard surface. If [...]

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference and radio communications[...]

Foreign substances Exercise care to prevent dirt and foreign objects from entering the DVD player compartment. Be especially careful not to spill liquids of any kind onto the media controls or into the system. If liquid is accidentally spilled onto the system, immediately turn the system OFF and consult a qualified service technician. Cleaning the [...]

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control: : Distributes outs[...]

T o increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. MANUAL HEATING AND AIR CONDITIONING SYSTEMS (IF EQUIPPED) • Manual heating and air conditioning system ?[...]

1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recirculated air through the i[...]

Operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position. • T o reduce humidity build up inside the vehicle, do not drive with the air flow selector in the O (OFF) position. • Do not put objects under the front seats that will interfere with the airflow to the rear seats. ?[...]

DUAL AUTOMATIC T EMPERATURE CONTROL (DA TC) SYSTEMS (IF EQUIPPED) • DA TC • DA TC with heated mirrors 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Climate Controls 75[...]

• DA TC with heated seats and heated mirrors T emperature conversion: T o switch between Fahrenheit and Celsius, refer to Units (English/Metric) under either Standard Message Center or Optional Message Center in the Driver Controls chapter In order to achieve maximum cooling performance, press , A/C, , and set the temperature to 60°F (16°C) and[...]

4. Recirculation control: Press to activate/deactivate air recirculation in cabin. Recirculated air may reduce the amount of time to cool down the interior of the vehicle and may also help reduce undesired odors from reaching the interior of the vehicle. Recirculation can be engaged manually in any other airflow selection except (defrost). Recircul[...]

Dual Automatic T emperature Control (DA TC) system operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position. • T o reduce humidity build up inside the vehicle, do not drive with the system OFF , or with recirculated air engaged and A/C off. • Do not put objects under the fro[...]

• T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the m[...]

HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also kee[...]

Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the ON position, • the headlamp control is in the OFF or parking lamp position and • the parking brake must be disengaged. Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime [...]

PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable illuminated switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. AIMING THE HEADLAMPS Y our vehicle may be equipped with a sealed beam or aerodynamic headl[...]

• (4) Horizontal reference line • (5) Center of headlamps • (6) Center line of the vehicle 2. The center of the headlamp is marked either on the lens (a circle or cross marker) or on the bulb shield, internal to the lamp (mark or feature). Measure the height from the center of your headlamp to the ground (2) and mark an 8 foot (2.4 meter) lon[...]

V ertical aim adjustment (aerodynamic headlamps) The headlamps on your vehicle can only be vertically adjusted. Y our vehicle does not require horizontal aim adjustments. T o adjust the headlamps: 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away . • (1) 8 feet (2.4 meters) • ([...]

T URN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. MAP LAMPS (IF EQUIPPED) The dome lamp lights when: • any door is opened, • the instrument panel dimmer switch is rotated up until the courtesy lamps come on, and • any of the remote entry controls are pressed and the ignition is[...]

Function Number of bulbs T rade number Sidemarker 2 194 T ail/stop/turn/sidemarker (Pick-up only) 2 4157K or 3157 T ail/stop/turn/sidemarker (Chassis cabs only) 2 3157 Back-up (Pick-ups only) 2 3156 or 3156K Back-up (Chassis cabs only) 2 3157 High-mount stoplamp 1 906 Foglamp 2 9145 License plate lamp 2 194 Cargo lamp 2 906 Mirror turn signal 2 282[...]

2. Remove the four bolts from the top, side and bottom front of the headlamp assembly . 3. Pull the assembly straight out disengaging two snap clips to fender . 4. Disconnect the electrical connector by squeezing the release tab and pushing the connector forward and then pulling it rearward. 5. Remove the bulb assembly by turning it counterclockwis[...]

Replacing park/turn and sidemarker lamp bulbs (aerodynamic) 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Remove the four bolts from the top, side and bottom front of the headlamp assembly . 3. Pull the assembly straight out. 4. Remove the bulb assembly , (1) sidemarker or (2) park/turn by turning it counterclo[...]

Replacing headlamp bulbs (sealed beam) 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Remove the three screws and one bolt from the top and bottom of the park lamp/bezel assembly . 3. Remove the four screws and the headlamp retaining ring from headlamp. 4. Disconnect the electrical connector from the headlamp. I[...]

Replacing park/turn/sidemarker bulbs (sealed beam) 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Remove the four bolts from the top, side and bottom of the park lamp/bezel assembly . 3. Pull the assembly straight out disengaging snap clip. 4. Remove the bulb assembly , sidemarker or park/turn by turning it coun[...]

Replacing brake/tail/turn/back-up lamp bulbs - Pick-ups only 1. Make sure the headlamp switch is in the OFF position and then open the tailgate to expose the lamp assemblies. 2. Remove the two bolts from the tail lamp assembly and carefully pull the lamp assembly from the tailgate pillar by releasing the two retaining tabs. 3. Rotate the bulb socke[...]

Replacing cargo lamp and high-mount brakelamp bulbs 1. Make sure the headlamp switch is in the OFF position. 2. Remove the two screws and lamp assembly from vehicle as wiring permits. 3. Remove the bulb socket by rotating counterclockwise. 4. Pull the bulb straight out of the socket. Front clearance and identification lamp bulbs 1. Make sure the he[...]

Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper . T o change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2. T wist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly . 3. Pull out the old bulb from the socket and push in the new [...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three [...]

TILT STEERING WHEEL (IF EQUIPPED) 1. Pull and hold the steering wheel release control toward you. 2. Move the steering up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position. Never adjust the steering column when the vehicle is moving. T RANSMISSION CONTROL T ow/H[...]

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’ s overhead console will vary according to your option package. If your vehicle is equipped with a moon roof, refer to One-touch moonroof later in this chapter for information on its operatio[...]

The auxiliary power point is located on the instrument panel. On SuperCab and Crew Cab models, another power point is located on the rear of the center console (if equipped). Do not use the power point for operating the cigarette lighter element (if equipped). T o prevent the fuse from being blown, do not use the power point(s) over the vehicle cap[...]

POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and pull the window switc[...]

Power rear slider window (if equipped) Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. • Pr[...]

The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) (when the mirror is on) to ensure a bright clear view when backing up. Do not block the sensors on the front and back of the inside rear view mirror since this may impair proper mirror performance. Do not clean the housing or glass of any mirror w[...]

If equipped with powerfold mirrors, you can fold the side mirrors simultaneously using the power mirror switch. 1. Rotate the switch to the center/neutral position. 2. Momentarily pull the switch rearward to auto fold in. 3. Momentarily pull the switch rearward again to fold back to design position. Note: When powerfolding the mirrors, it is normal[...]

the mirrors at high speeds, they may not fully fold forward/rearward - slow down and powerfold or manually fold the mirrors in order to complete the fold operation. If the powerfold mirrors feel loose or fold very easily , it is possible that the powerfold mechanism is out of sync. The powerfold mechanism gets out of sync when a mirror is manually [...]

Memory mirrors (if equipped) This system allows automatic positioning of the outside rearview mirrors. For more information on this feature, refer to Memory seats/power mirrors/adjustable pedals in the Seating and Safety Restraints chapter . Mirror mounted side turn signal indicator (if equipped) When the vehicle turn signals are activated, the out[...]

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you. The adjustment allows for approximately 2.75 inches (70 mm) of maximu[...]

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. No[...]

Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. Y ou can also use the SET [...]

Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED)[...]

In AM, FM1, or FM2 mode: • Press SEEK to select preset stations within the selected radio band or press and hold to select the next/previous radio frequency . In Satellite radio mode (if equipped): • Press SEEK to advance through preset channels or subscribed channels. In CD mode: • Press SEEK to select the next selection on the CD or press a[...]

Press F AN + or - to adjust fan speed. UPFITTER CONTROLS (IF EQUIPPED) Y our vehicle may be equipped with the Upfitter option package which will provide four switches, mounted in the center of the instrument panel, labeled AUX 1, AUX 2, AUX 3 and AUX 4. These switches will only operate while the ignition is in the 3 (ON) position, whether the engin[...]

The relays are coded as shown in the accompanying illustration. There will also be one power lead for each switch found as a blunt-cut and sealed wire located below the instrument panel and to the left of the steering column. They are coded as follows: Switch Circuit number W ire color Fuse AUX 1 CAC05 Y ellow 30A AUX 2 CAC06 Green with Brown T rac[...]

Note: The moon roof will open to the “comfort” position first before opening all the way . The “comfort” position helps to alleviate rumbling wind noise which may happen in the vehicle with the roof fully opened. T o open the moon roof: The moon roof is equipped with a one-touch open feature. Press and release the AUTO control. The moon roo[...]

HOMELINK 姞 WIRELESS CONTROL SYSTEM The HomeLink 威 W ireless Control System, located on the driver’ s visor , provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security syste[...]

1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat Step 1 to program additional hand-held transmitters to the remaining two HomeLink 威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink 威 . 2. Position the end of your hand-held[...]

Note: There are 30 seconds in which to initiate Step 7. 7. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink 威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to comp[...]

Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button. Activation will now occur for the trained product (garage door , gate operator , security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used a[...]

CENTER CONSOLE (IF EQUIPPED) Y our vehicle may be equipped with a variety of console features. These include: • Utility compartment with cassette/CD holder • Coin holder • Pen holder • W riting surface • A power point inside and on the rear • Laptop storage • Hanging file folder supports • Rear cupholders (Crew Cab only) Use only so[...]

• A verage Fuel Economy • Setup Menu • System check • Blank (Odometer and compass, if equipped, off) Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter . Distance to empty (DTE) Selecting this function from the INFO MENU estimates approximately how far you can drive with the fuel remaining in your tank under normal dri[...]

• Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the SELECT/RESET control switch (press and hold for 2 seconds in order to reset t[...]

Language Note: When entering the SETUP MENU and a non-English language has been selected, “PRESS RESET FOR ENGLISH” will be displayed to change back to English. 1. Select this function from the SETUP MENU for the current language to be displayed. 2. Press and hold the SELECT/RESET control to select a new language. Selectable languages are Engli[...]

The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the SELECT/RESET control and clearing the warning message. W arning messages that have been reset are divided into two categories: • They[...]

P ARK BRAKE ENGAGED Displayed when the parking brake is applied (or not fully released). CHECK BRAKE SYSTEM Displayed when a fault has been detected by the ABS module. TRAILER F AUL T (if equipped): Displayed if there is a short circuit on the electric brake output wire or the trailer brakes are drawing too much current. Refer to Integrated trailer[...]

OPTIONAL MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the RUN position, the message center , located on your instrument cluster , displays important vehicle information through a constant monitor of vehicle systems. Yo u may select display features on the message center for a display of status. The system will also notify you of potential veh[...]

Info menu This control displays the following control displays: • T rip Odometer A or B • Distance to Empty • A verage Fuel Economy • Drive T ime (Elapsed T ravel T imer) • Blank (Odometer and compass, if equipped, off) Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter . Distance to empty (DTE) Selecting this functi[...]

Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing miles traveled since last fill-up by gallons of fuel used (multiply liters used by 100, then divide by kilometers traveled), your figure may be different tha[...]

Setup menu Press this control for the following displays: • System Check • Units (English/Metric) • Autolamp T imer Presets (if equipped) • Autolock On/Off (if equipped) • Compass calibration • Language • Reset to English (if in another language) (see Note below) Note: When returning to the SETUP menu and a non-English language has be[...]

3. AIR FIL TER (Diesel engine only) 4. DOOR AJAR 5. BRAKE SYSTEM 6. FUEL LEVEL Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. Autolamp timer presets This feature keeps your headlights on for up to three minutes after the ignition [...]

Usually , when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary . Refer to Compass zone/calibration adjustment. Most geographic areas (zones) have a magnetic north compass point[...]

7. Press the RESET control to start the compass calibration function. 8. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CIRCLE SLOWL Y TO CALIBRA TE display changes to CALIBRA TION COMPLETED. It will take up to five circles to complete calibration. 9. The compass is now calibrated. Note: If the RESET control is pressed or[...]

W arning messages that have been reset are divided into two categories: • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-RUN cycle has been completed. This acts as a reminder that these warning conditions still exist within the vehicle. W arning display Status Park brake engaged W ar[...]

TRAILER F AUL T (if equipped): Displayed if there is a short circuit on the electric brake output wire or the trailer brakes are drawing too much current. Refer to Integrated trailer brake controller in the T ires, Wheels and Loading chapter for more information. TBC F AUL T (if equipped): Displayed in response to faults sensed by the trailer brake[...]

T AILGATE LOCK (IF EQUIPPED) Y our vehicle may be equipped with a tailgate lock designed to help prevent theft of the tailgate. • Insert ignition key and turn to the right to engage lock. • T urn ignition key to the left to unlock. T ailgate removal Y our tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a scre[...]

T ailgate step (if equipped) Y our vehicle may be equipped with a feature that allows easier entry into the truck bed. T o open the tailgate step: 1. Flip down the tailgate. 2. Pull the yellow latch lever to the Unlock positon ( ) to release the grab handle from it’ s stowed postion and raise the handle upright until you feel it latch and see the[...]

• Replace slip resistance tape (serviceable item) if worn out. • Replace handle molding (serviceable item) if damaged. • Do not tow with grab handle or step frame. Bed extender (if equipped) Y our vehicle may be equipped with a cargo management feature in the truck bed. Note: This feature is not intended for off-road usage. T o open the bed e[...]

3. Rotate the panels toward the tailgate. Repeat Steps 1–3 for the other side of the bed extender . 4. Connect the two panels, then rotate both knobs a quarter -turn clockwise to secure the panels. 5. Ensure the latch rod is inserted into the tailgate hole and the locking pins on both sides are engaged into their holes in the pick-up box. 6. Reve[...]

Note: When the vehicle is in motion, ensure the locking pins and knobs are fully engaged. Note: Ensure all cargo is secured. Note: When the vehicle is in motion, the tailgate load must not exceed 150 lbs. (68 kg). T o open the bed extender into Grocery Mode, follow Steps 1–5 by rotating the panels away from the tailgate. 2008 F-250/350/450/550 (f[...]

KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . If your vehicle is equipped with the SecuriLock 娂 Passive Anti-theft system, your keys are coded to your vehicle; using a non-coded key will not permit your vehicle to start. If you lose your dea[...]

• the ignition is in the 3 (ON) position, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h) for greater than 2 seconds. The autolock feature repeats when: • any door is opened then closed while the ignition is in the 3 (ON) position and the vehicle speed is 9 mph (15 km/[...]

6. T o enable/disable the autolock feature, press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. T urn the ignition to the 1 (OFF/LOCK) position. The horn will chirp once to confirm the procedure is complete. Keyless entry ke[...]

Note: The autounlock feature can be activated/deactivated independently of the autolock feature. Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the 1 (OFF/LOCK) position and all vehicle doors are closed. Y ou must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated.[...]

The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled. CHILDPROOF DOOR LOCKS (IF EQUIPPED) • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The chi[...]

• structures around the vehicle, or • other vehicles parked next to your vehicle. Y our vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without a key . • lock all the vehicle doors without a key . • activate the personal alarm. If there are problems with the remote entry system, make sure to [...]

Note: The panic alarm will only operate when the ignition is in the 1 (OFF/LOCK) position. Memory seats/adjustable pedals/mirrors (if equipped) The remote entry system can also control the memory seat/adjustable pedals/mirrors. Press to automatically move the seat, adjustable pedals and mirrors to the desired memory position (the seat position corr[...]

T o replace the battery: 1. T wist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT T AKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . N[...]

transmitter to each memory position using this procedure. The first transmitter that is programmed will recall Driver 1 settings, and the second transmitter that is programmed will recall Driver 2 settings. How to program your remote entry transmitters Y ou must have all remote keyless entry keypads and remote entry transmitters (maximum of four) a[...]

The lamps will automatically turn off: • if the ignition switch is turned to the 3 (ON) position, or • the Remote Keyless Entry T ransmitter lock control is pressed, or • the vehicle is locked using the keyless entry keypad (if equipped), or • after 25 seconds of illumination. Note: On some vehicles, the perimeter lamps illuminated entry fe[...]

Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the 3 (ON) position, or • the remote transmitter lock control is pressed, or • the 7 • 8 and the 9 • 0 controls on the keyless ent[...]

3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other . 4. T o associate the entry code with a memory setting, enter a sixth digit to indicate which driver should be set in a memory recalled by the personal entry code: • Pressing 1 • 2 recalls Driver 1 settings. • Pressing 3 • 4 recalls Driver 2 [...]

Unlocking and locking the doors using keyless entry T o unlock the driver’ s door , enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other . The interior lamps will illuminate after entering a valid keypad entry code. T o unlock all doors, press the 3 • 4 control within five secon[...]

• When the ignition is in the 3 (ON) position, the indicator will glow for 3 seconds to indicate a programmed key has been validated and the SecuriLock 娂 Passive Anti-theft system has enabled the engine. V ehicles without the SecuriLock 娂 Passive Anti-theft system behave as follows: • When the ignition is in the 1 (OFF/LOCK) position, the i[...]

operate your vehicle’ s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure. If two previously programmed coded keys are not available, you must bring your vehicle to your authorized dealer to have the spare coded key(s) programmed. Please read and understand the entire procedure befo[...]

SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Adjustable head restraints (if equipped) The purpose of these head restraints[...]

Full bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Pull up on the lever located at the bottom of the seatback to quickly fold the seatback forward. • Pull up on the lever located at the side of the seat cushion to recline the seatback and to return the sea[...]

40/20/40 front seat armrest and console (if equipped) T o release the armrest, pull forward on the strap and pull the armrest down. T o gain access to the storage compartment in your armrest, lift the latch to open the lid. The lid cannot be opened in the upright position. Lift up armrest to return it to a center seatback. 2008 F-250/350/450/550 (f[...]

Captain’ s chair (if equipped) • Lift the bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • T o recline the seatback, pull the release lever handle located on the side of the seat up. • Push down the lever (if equipped) located at the bottom of the seatback to quickly fold the seatback forward. Adj[...]

Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Using the manual lumbar support The lumbar support control is located on the outboard side of the seat T urn the lumbar support clockwise for more s[...]

T o operate the heated seats, do the following (engine must be running): Push to activate; push again to deactivate. The indicator light on the control will illuminate when activated. The system will automatically shut off after 10 minutes unless the control is pushed to deactivate. The system will reset after each ignition key cycle. Memory seats/[...]

REAR FOLDING SEAT SYSTEM WITH LOAD FLOOR (IF EQUIPPED) The rear seatback has a split 60/40 seat. Each seat cushion can be flipped up into the seatback position. Note: The Crew Cab rear 60/40 split bench seatback is not intended to support a cargo load in the forward-folded position. T o fold the seatback down, pull down the latch lever located on t[...]

T o gain access to the cupholders and tray , pull down on the armrest. T o gain access to the 60/40 load floor , store the cushion in the upright locked position. Pull up on the straps located at the sides of the load floor , and rotate forward until resting on the carpet. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with y[...]

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety [...]

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle. V ehicle sensitive mode [...]

This mode should be used any time a child safety seat is installed except a booster in a front or rear outboard passenger seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter . How t[...]

BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in the W orkshop Manual . Failure to replace the belt and retractor assembly could increase the risk of injury in collisions. Energy Man[...]

Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. T o adjust the shoulder belt height, push the button and slide the height adjuster up or down. Release the bu[...]

2. Insert the belt into the clip on the back panel. Protect the stowed belt if you carry cargo this may damage or soil the belt. If the belt has been disconnected to carry large objects behind the seat, reconnect it as follows: 1. Remove the belt from the stowage clip on the back panel. 2. Buckle the small tongue on the end of the belt into the min[...]

longer . The cinch tongue is designed to slip during a crash, so always wear the shoulder belt properly and don’t allow any slack in either the lap or shoulder portions. Before you can reach and latch a combination lap and shoulder belt having a cinch tongue into the buckle, you may have to lengthen the lap belt portion of it. 1. T o lengthen the[...]

Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around the hips, not across the waist. • 1st row center seating position on Super Cab and Crew Cab The lap belt does not adjust automatically . Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o length[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.[...]

The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our [...]

Do not sit on tope of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. T o do so may adversely affect the performance of the vehicle’ s air bag system One-time disable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, the Belt-Minder 威 will be disabled for that ig[...]

• Step 3 must be completed within 60 seconds after the safety belt warning light turns off. 3. At a moderate speed, buckle then unbuckle the safety belt 9 times, ending with the safety belt in the unbuckled state. • After Step 3 is complete, the safety belt warning light will be turned on for 3 seconds. • If Step 4 does not occur within 10 se[...]

assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar -if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if equipped), child safety seat LA TCH and tether anchors, and attaching hardware, should be inspected after a collision. Ford Motor Company [...]

Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag. All occupants of the vehicle, including the driver , should always properly wear their safety belts, even [...]

Do not attempt to service, repair , or modify the airbag supplemental restraint systems or its fuses. See your authorized dealer . The front passenger air bag is not designed to offer protection to an occupant in the center front seating position. Modifying or adding equipment to the front end of the vehicle (including frame, bumper , front end bod[...]

How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activatio[...]

If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger airbag modules (which include the inflators and airbags), • one or more impact and safing sensors, ?[...]

Passenger airbag ON/OFF switch (if equipped) An airbag ON/OFF switch has been installed in this vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper position in accordance with these instructions and warnings. Failure to put the switch in a proper position can increase the risk of serious injury or d[...]

An infant in a rear -facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unless the passenger airbag is turned off. Turning the passenger airbag back on The passenger airbag remains OFF until you turn it back ON. 1. Insert the ignition key [...]

If your vehicle has rear seats, always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly . If a child in a rear facing infant seat must be transported in front, the passenger airbag must be turned OFF . This is because the back of the infant seat is too close to the inflating airbag an[...]

• the child has a medical condition which, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’ s condition. 3. Medical condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger airbag to pose[...]

• the child has a medical condition that, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can monitor the child’ s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a special risk for the passenger if the ai[...]

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. Children and safety belts If the child is the proper size, restrain the child in a safety seat. C[...]

lap/shoulder belt to fit properly . Generally this is when they weigh about 80 lb. (36 kg) (about 8 to 12 years old). Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? • Does th[...]

• Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’ s head, a high back booster seat would be a better choice. Either type can be used at any seating position equipped with lap/shoulder belts if your child is over 40 lb. (18 kg). Children and booster seats vary wide[...]

Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’ s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or towels to boost a child. They can slide around a[...]

• T op tether anchors can be used for children up to 60 pounds (27 kg) in a child restraint, and to provide upper torso restraint for children up to 80 pounds (36 kg) using an upper torso harness and a belt-positioning booster . Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating po[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. T[...]

• F-Series Crew Cab T ether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position. 4. Y ou may need to pull the seatback forward to access the tether anchors. Make sure the seat is locked in the u[...]

• Front seat (SuperCab) • Rear seats (Crew Cab) If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 7. Refer to the Installing child safety seats with combination lap and shoulder belts section of this chapter for further instructions to secure the child safety seat. 8. T [...]

Many tether straps cannot be tightened if the tether strap is hooked to the loop directly behind the child seat. T o provide a tight tether strap: 1. Route the tether strap through the loop directly behind the child seat. 2. Attach the strap hook onto the loop behind an adjacent seating position. 3. Install the child safety seat tightly using the v[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on shifting procedures and maintenance can be found in your Owner’ s Guide .Y o u should become thoroughly familiar with this information before you operate your vehicle. On some 4W[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versa[...]

government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however , and may depart significantly from the norm due to variations in driving habits, service practices, a[...]

• T ire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a[...]

At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company . Use a tire gauge to check the tire inflation pressure, including the spare (if equipped), at least monthly and before long trips.[...]

T o check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recomme[...]

Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, they cannot be treated like normal light truck tires. T ire service, including adjusting the air pressure, must be performed by personnel trained, supervised and equipped according to Federal Occupational Sa[...]

Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Al[...]

Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydropla[...]

U.S. DOT Tire Identification Number (TIN) U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification and [...]

When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi greater than t[...]

Highway hazards No matter how carefully you drive there’ s always the possibility that you may eventually have a flat tire on the highway . Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect[...]

• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD) (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask your authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y [...]

• DRW – Six tire rotation If your vehicle is equipped with dual rear wheels it is recommended that the front and rear tires (in pairs) be rotated only side to side. W e do not recommend splitting up the dual rear wheels. Rotate them side to side as a set/pair . After tire rotation, inflation pressures must be adjusted for the tires new position[...]

Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the T ire and Rim Association (T&RA), that[...]

Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186[...]

12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire grad[...]

Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/L[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and Rim A[...]

Note: Do not use snow chains on front tires of vehicles with 20” wheels and tires. The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same size and specifications) be u[...]

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label (vehicles exported outside the U.S. and Canada may not have a T ire Label) on the B-Pillar or the edge of the driver’ s door . Look for “THE COMBINED WEIGHT OF OCCUP ANTS AND CARGO SHOULD [...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2008 F[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Exceeding the Safety Compliance Certif[...]

GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The GVW must never exceed the GVWR. GCW (Gross Combined W eight) ?[...]

T ongue Load or Fifth Wheel King Pin W eight – refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5,000 lb. (2,268 kg) conventional trailer , multiply 5,000 by 0.10 and 0.15 to obtain a proper tongue load range of 500 to 750 lb. (227 to 340 kg). For an 11,500 lb. (5,216 kg) fifth wheel trailer , mult[...]

The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity: • Another example for your vehicle with 1,400 lb. (635 kg) of cargo and luggage capacity . Y ou decide to go golfing. Is there enough load capacity to carry you, 4 of your friends and all the golf bags? Y ou and four friends average[...]

Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Y our vehicle can haul more cargo and people than most passenger cars. Depending upon the type and placement of the load, hauling cargo and people may raise t[...]

Note: Do not exceed the GCWR listed for your vehicle on the following chart/table, or the GVWR, GA WR or tire ratings specified on the Tire Label or Safety Compliance Certification Label. T owing trailers beyond the maximum recommended trailer weight which exceeds the limit of the vehicle’ s GCWR, GVWR, GA WR or tire ratings could result in engin[...]

Maximum GCWR - lb. (kg.) Engine Rear axle ratio Manual transmission Automatic transmission F–350 Dual Rear Wheel (DR W) Chassis Cab 5.4L 3.73 15000 (6804) 16500 (7484) 4.10 17500 (7938) 18500 (8391) 6.8L 4.10 20500 (9299) 21500 (9752) 4.30 22500 (10206) 23000 (10433) F–450 Chassis Cab/F–550 6.8L 4.88/5.38 26000 (11793) 26000 (11793) Preparing[...]

Hitch T ype Maximum Gross T railer W eight — lb. (kg) Maximum T ongue W eight — lb. (kg) 6.8L DRW Pickup 2.5” ID without adapter (requires 2.5” drawbar) W eight carrying 8000 (3629) 800 (363) W eight distributing 15000 (6804) 1500 (680) 6.8L DRW Pickup 2.5” ID with adapter (requires 2” drawbar) W eight carrying 6000 (2721) 600 (272) W e[...]

Note: Adjusting a weight distributing hitch so the rear bumper of the vehicle is higher than it was unloaded will defeat the function of the weight distributing hitch and may cause unpredictable handling. Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle hitch. T o connect the trailer’ s saf[...]

The TBC user interface consists of the following: 1. +/- (GAIN adjustment buttons): Pressing these buttons will adjust the TBC’ s power output to the trailer brakes (in 0.5 increments). The GAIN setting can be increased to a maximum of 10.0 or decreased to a minimum of 0 (no trailer braking). Pressing and holding a button will raise or lower the [...]

• Stop Lamps: Activating the TBC manual control lever will illuminate both the trailer brake lamps and the tow vehicle brake lamps except the Center High-Mount Stop Lamp (presuming proper trailer electrical connection). Pressing the vehicle brake pedal will also illuminate both trailer and vehicle brake lamps. GAIN The GAIN setting is used to set[...]

TBC determines a malfunction in the trailer connection, TBC system, or in the trailer . These messages are listed below: TRAILER DISCONNECTED (if equipped with message center) or CHECK TRAILER (if equipped with mini message center): This message is displayed when a trailer connection was determined and then a disconnection, either intentionally or [...]

• A void towing in adverse weather conditions. The TBC does not provide anti-lock control of the trailer wheels. T railer wheels can lock-up on slippery surfaces, resulting in reduced stability of trailer and tow vehicle. • The TBC interacts with the brake system of the vehicle, including ABS, in order to reduce the likelihood of trailer wheel [...]

information, refer to the Understanding the shift positions of the 5–speed automatic transmission section in the Driving chapter . • Anticipate stops and brake gradually . • Do not exceed the GCWR rating or transmission damage may occur . • Y our vehicle may be equipped with a temporary or conventional spare tire. If the spare tire is diffe[...]

Loading • Keep the center -of-gravity low for best handling. • T railer loads should be evenly distributed front to back and left to right. • The load distribution within the trailer should be such that 10%–15% of the trailer weight is on the hitch. (15%–25% for fifth-wheel or gooseneck towing.) • Never exceed truck, trailer , receiver [...]

• Disconnect the trailer tow electrical connector to prevent blown fuses caused by water entering into your trailer’ s electrical wiring. Exceeding these limits may allow water to enter critical vehicle components, adversely affecting driveability , emissions and reliability . Replace front and rear axle lubricants any time the axles have been [...]

STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engine and all accessories/locks the steering wheel, gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. This position also unlocks the steering wheel. 3. ON, all electrical circuits operational. [...]

If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked. If your vehicle is operat[...]

If starting a vehicle with a manual transmission: 1. Make sure the parking brake is set. 2. Push the clutch pedal to the floor . • T urn the key to 3 (ON) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning l[...]

Note: If the engine does not start within five seconds on the first try , turn the key to OFF , wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel. If your vehicle has an automatic tran[...]

T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out and should be inspected by your authorized dealer . If the ve[...]

effectiveness of the ABS and will increase your vehicle’ s stopping distance. The ABS will be activated immediately , allowing you to retain full steering control during hard braking and on slippery surfaces. However , the ABS does not decrease stopping distance. Parking brake T o set the parking brake, press the parking brake pedal down until th[...]

If you’re parking your vehicle on a grade or with a trailer , press and hold the brake pedal down, then set the parking brake. There may be a little vehicle movement as the parking brake sets to hold the vehicle’ s weight. This is normal and should be no reason for concern. If needed, press and hold the service brake pedal down, then try reappl[...]

The T raction Control 娂 switch, located on the instrument panel to the left of the climate control system, has an indicator light that illuminates when the system is off. The T raction Control 娂 system will automatically turn on every time the ignition is turned off and on. The T raction Control 娂 system should normally be left on. If you sho[...]

torque features which may not be re-used). Never re-use a bolt or nut. T orque fasteners to specifications in Workshop Manual . A high crown in the road or high crosswinds may also make the steering seem to wander/pull. T RACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor [...]

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the 3 (ON) position and the brake pedal is not depressed. If you cannot move the gearshift lever out of the P (Park) position with[...]

Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer as soon as poss[...]

Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutra[...]

T o deactivate the T ow/Haul feature and return to normal driving mode, press the button on the end of the gearshift lever . The TOW HAUL light will no longer be illuminated. When you shut-off and restart the engine, the transmission will automatically return to normal D (Overdrive) mode (T ow/Haul OFF). Do not use the T ow/Haul feature when drivin[...]

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transmission has a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. T o start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor , then put the gearshift lever in the neutral position. [...]

Shift according to the following shift speed charts: Upshifts when accelerating (recommended for best fuel economy) 6-speed transmission Shift from: T ransfer case position 1 (if equipped) 2H or 4H 4L LO-1 5 mph (8 km/h) 2 mph (3 km/h) 1-2 15 mph (24 km/h) 6 mph (10 km/h) 2-3 22 mph (35 km/h) 9 mph (14 km/h) 3-4 30 mph (48 km/h) 12 mph (19 km/h) 4-[...]

3. T urn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully . REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) is selected and the vehicle is[...]

The RSS detects obstacles up to 6 feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away , the tone will sound conti[...]

If your vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this [...]

engaged, the vehicle speed must be below 5 mph (8 km/h) with the brake pedal depressed and the transmission in N (Neutral). If your vehicle is equipped with a manual transmission, the clutch pedal also must be depressed.This vehicle is equipped with a non-synchronous low range gearset which will not allow the transfer case to shift into 4X4 LOW if [...]

• 4x4 LOW – momentarily illuminates when the ignition is turned to the ON position. Illuminates when 4L (4x4 Low) is engaged. Using a Manual Shift On Stop (MSOS) 4x4 system (if equipped) Note: High shift efforts may be encountered when attempting to shift into and out of 4x4 modes. It is recommended to allow the vehicle to roll at a speed below[...]

• Do not shift into 4H (4x4 High) with the rear wheels slipping. Shifting from 4H (4x4 High) to 2H (2WD) Move the transfer case lever to 2H (2WD) at a stop or a vehicle speed below 5 mph (8 km/h). W ith the vehicle at complete stop, disengage the locking hubs (optional) by rotating the hub lock control from LOCK to FREE. • For proper operation,[...]

3. Move the transfer case shift lever through N (Neutral) directly to 4H (4x4 High) or 2H (2WD). 4. If the transfer case will not engage into 4H (4x4 High) or 2H (2WD), perform a shift with the transmission in N (Neutral) (or clutch pedal depressed) and the vehicle rolling at a speed below 5 mph (8 km/h). 5. If shifting to 2H (2WD) with the vehicle[...]

4x4 LOW – For low-speed off-road applications that require extra power such as steep grades, deep sand or pulling a boat out of the water . Sends power to front and rear wheels. This mode is not intended for use on dry pavement. Shifting from 2WD to 4x4 HIGH Rotate the 4x4 control to the 4x4 HIGH position at speeds up to 55 mph (88 km/h). • The[...]

4. Move the 4x4 control to the 4x4 LOW position. 5. Hold the shift conditions until the 4x4 LOW indicator light illuminates. 6. If the 4x4 LOW indicator light does not illuminate within 15 seconds, allow the vehicle to move at a speed below 5 mph (8 km/h), then repeat steps 2 through 5 while the vehicle is rolling before reporting any shift concern[...]

Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. Y ou should either know the t[...]

V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road[...]

V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road[...]

can be found in the Maintenance and Specifications chapter . Y ou should become thoroughly familiar with this information before you operate your vehicle. Normal characteristics On some 4WD models, the initial shift from two-wheel drive to 4x4 while the vehicle is moving can cause some momentary clunk and ratcheting sounds. This is the front drivet[...]

Refer to T ransmission temperature gauge in the Instrument Cluster chapter for transmission fluid temperature information. If the front or rear axle is submerged in water , the axle lubricant should be replaced. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts c[...]

Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, manually shift to a lower gear . Y our vehicle has anti-lock brakes, apply the brakes steadily . Do not “pump” the brakes. Driving on snow and ice 4WD vehicles have advantages over 2W[...]

Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carrying capability . For this reason, Ford Motor Company strongly recommends that you do not make modifications such as adding or removing parts (such as lift ki[...]

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water , traction or brake capability may be limited. Also, wate[...]

• Rear ballast weight behind the rear axle may be required to prevent exceeding the FGA WR, and provide front-to-rear weight balance for proper braking and steering. • Front wheel toe may require re-adjustment to prevent premature uneven tire wear . Specifications are found in the Ford W orkshop Manual. • Headlight aim may require re-adjustme[...]

All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. Never remove or defeat the “tripping mechanisms” designed into the snow removal equipment by its manufacturer . Doing so may cause damage to the vehicle and the snow removal e[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the period of five years or 60,000 miles[...]

Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick re[...]

HAZARD FLASHER The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it whe[...]

The switch has a red button on top of it. T o reset the switch: 1. T urn the ignition off. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. T urn the ignition on. 5. W ait a few seconds and return the key to off. 6. Make another check for leaks. FUSES AND RELAYS Fuses If electri[...]

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

T o remove the fuse panel cover , pull the panel toward you. When the clips of the panel disengage, let the panel fall easily . T o remove a fuse use the fuse puller tool provided on the fuse panel cover . Always disconnect the battery before servicing high current fuses. Always replace the cover to the passenger compartment fuse panel before recon[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 30A Not used (spare) 2 15A Not used (spare) 3 15A Family Entertainment System (FES) 4 30A Not used (spare) 5 10A Keypad illumination, Brake-Shift Interlock (BSI) 6 20A T urn signals 7 10A Left headlamp (Low beam) 8 10A Right headlamp ([...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 12 7.5A Power mirror switch, Driver power seat (Memory) 13 7.5A Not used (spare) 14 10A Upfitter relay #3 feed 15 10A Climate control head 16 15A Upfitter Relay #4 Feed 17 20A All lock motor feeds 18 20A Heated seat relay feed 19 25A Not used (spare) 20 15A Adjustable [...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 35 10A Reverse Sensing System (RSS), 4x4 module, 4x4 solenoid, T raction control switch, T ow/Haul switch (Diesel engine) 36 5A Passive Anti-Theft System (P A TS) transceiver , Cluster control 37 10A Dual automatic or Manual climate control, PTC control 38 20A Subwoofe[...]

If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter . The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 Relay Blower motor/V ariable blower control (Dual Zone Climate Control) 2 Relay Electronic Shift-on-t[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 17 Relay Not used 18 Relay Fuel Pump Driver Module (FPDM), Fuel injectors (Gasoline engines), Diesel Fuel Control Module (DFCM) (Diesel engine) 19 Relay Back-up lamps, Reverse Sensing System (RSS), Engine compartment fuse 63 20 Relay T railer stop/turn (Left) 21 Relay T railer s[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 39 50A* ECM power (Diesel engine) 40 30A* Starter relay 41 20A* Power point (Center console - Front) 42 30A* T railer park lamp relay 43 20A* Power point (Center console - Rear) 44 30A* T railer battery charge relay 45 30A* Driver power seat or Memory module 46 40A* Run/Start re[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 66 — Not used 67 — Not used 68 — Not used 69 — Not used 70 10A** Gasoline engines: A/C clutch relay coil, Refrigerant Containment Switch, Heated PCV Diesel engine: A/C clutch relay coil, Clutch switch, Fuel pump cooler , A/C cycle pressure switch 71 5A** Fuel pump relay [...]

The use of tire sealants may damage your tires. Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare tire/wheel, then it is intended for temporary use only . This means that if you need to use it, you should replace it[...]

• W inter weather driving capability • W et weather driving capability It is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire. If 4WD operation is necessary , do not operate above speeds of 10 mph (16 km/h) or for distances above 50 miles (80 km). 3. Full-size dissimilar spare without label on whee[...]

Refer to the instruction sheet (located in the glove box) for detailed tire change instructions. Park on a level surface, activate hazard flashers and set the parking brake. • Automatic transmission: Place gearshift lever in P (Park). • Manual transmission: Place gearshift lever in R (Reverse). • Electronic Shift-On-the-Fly (ESOF) 4x4: Place [...]

Removing the spare tire (with spare tire carrier only) 1. The following tools are required to remove the spare tire: • one handle extension and two typical extensions. T o assemble, align button with hole and slide parts together . T o disconnect, depress button and pull apart. • one wheel nut wrench. Slide over square end of jack handle. • V[...]

3. Fully insert the jack handle (with one extension) through the bumper hole and into the guide tube. The key and lock will engage with a slight push and counterclockwise turn. Some resistance will be felt when turning the jack handle assembly . 4. T urn the handle counterclockwise and lower the spare tire until you can slide the tire rearward and [...]

The following steps apply to F–250/F–350 Single Rear Wheel (SR W) vehicles only: 5. Insert the hooked end of the jack handle into the jack and use the handle to slide the jack under the vehicle. 6. Position the jack according to the following guides: • Front (4x2) • Front driver side (4x4) Note: Make sure the jack fits onto the flat area on[...]

• Front passenger side (4x4) Note: View shown from the rear of the vehicle to clearly identify the jack point. Place the jack directly under the axle. • Rear Never use the front or rear differential as a jacking point. T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start[...]

9. Replace the flat tire with the spare tire, making sure the valve stem is facing outward for all front wheels and single rear wheel vehicles. If replacing an inboard rear tire on dual rear wheel vehicles, the valve stem must be facing outward. If replacing the outboard wheel, the valve stem must be facing inward. Reinstall the lug nuts until the [...]

• Front driver side (4x4): F–350 DRW Note: Make sure the jack fits onto the flat area on the outboard side of the differential housing. • Front passenger side (4x4): F-350 DRW Note: View shown from the rear of the vehicle to clearly identify the jack point. Note: Place the jack directly under axle and inboard of the radius arm so that the jac[...]

• Rear: F-350 DRW • Rear: F-450/F-550 13. Insert the jack handle into the pump linkage. 14. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack’ s rated capacity . 15. Remove the lug nuts with t[...]

The following steps apply to all vehicles: 18. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 8–lug nut torque sequence 10–lug nut torque sequence 19. Stow the flat tire. Refer to Stowing the flat/spare tire if the[...]

Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing in the direction specified on the T ire Changing Instructions located in the glove box. 2. Slide the wheel partially under the vehicle and install the reta[...]

Bolt size Wheel lug nut torque* lb.ft. N • m M14 x 1.5 150 200 * T orque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. On all two-piece flat wheel nuts, apply one drop of motor oil between the flat washer and the nut. Do not apply motor oil to the wheel nut threads or the wheel[...]

Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fu[...]

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . + – + – + – + – 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 292[...]

4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the bat[...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s batter[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground using a wheel lift On 4x4 vehi[...]

Note: T owing an a 4x2 or an ESOF 4x4 vehicle with the rear wheels on the ground for more than 50 miles (80 km) and/or in excess of 35 mph (56 km/h) may cause damage to the automatic transmission. Note: On Dual Rear Wheel (DRW) vehicles, an outer rear wheel must be removed prior to using a wheel lift wrecker . If the vehicle is towed by other means[...]

GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repair[...]

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, c[...]

In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent a[...]

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide. However , if your warranty conc[...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]

If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .ford-esp.com. GETTING ASSIST A[...]

ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: w[...]

T o contact NHTSA, you may call the V ehicle Safety Hotline toll-free at 1–888–327–4236 (TTY : 1–800–424–9153); go to http://www.safercar .gov; or write to: Administrator NHTSA 400 Seventh Street, SW W ashington, D.C. 20590 Y ou can also obtain other information about motor vehicle safety from http://www.safercar .gov. REPORTING SAFETY [...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Ne[...]

racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Y our authorized dealer has touch-up paint and sprays to match your vehicle’ s color . T ake your color code (printed on a sticker in the driver’ s door jamb) to your authorized dealer to ensure[...]

• Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. • Cover the highlighted areas to prevent water damage when cleaning the engine. • 5.4L V8 gasoline engine • 6.8L V10 gasoline engine 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Cleaning 308[...]

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft Detail W ash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and T ar Remover (ZC-42). • For plastic headlamp lenses, use Motorcraft Ultr[...]

• Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens. Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system. If a staining liquid like coffee/juice has been spilled on the instrume[...]

LEATHER SEATS (IF EQUIPPED, EXCEPT FOR THE KING RANCH F–250 AND F–350 CREWCAB) Y our leather seating surfaces have a clear , protective coating over the leather . For King Ranch F-250 and F-350 CrewCab leather seats, refer to separate section in this chapter . • T o clean, use a soft cloth with Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-[...]

• Clean spills as quickly as possible. • T est any cleaner or stain remover on an inconspicuous part of the leather as cleaners may darken the leather . For more specific cleaning information, contact the King Ranch Saddle Shop at 1–800–282–KING (5464). • Do not spill coffee, ketchup, mustard, orange juice or oil-based products on the l[...]

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Y our authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from [...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a scheduled maintenance guide which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Ch[...]

2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the b[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Refer to the 6.0/6.4 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for diesel engine component locations. 5.4L V8 gasoline engines 1. W indshield washer fluid reservoir 2. Battery 3. T ransmission fluid dipstick (automatic transmission) 4. Engine oil filler cap 5. Engi[...]

6.8L V10 gasoline engine 1. W indshield washer fluid reservoir 2. Battery 3. T ransmission fluid dipstick (automatic transmission) 4. Engine oil filler cap 5. Engine oil dipstick 6. Power steering fluid reservoir 7. Brake fluid reservoir 8. Engine coolant reservoir 9. Air filter assembly 10. Power distribution box 2008 F-250/350/450/550 (f23) Owner[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellant-type fluid or bug wash as this may cause a squeaking/chattering noise[...]

4. Poor wiper quality can be improved by cleaning the wiper blades and the windshield; refer to Windows and wiper blades in the Cleaning chapter . 5. T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro [...]

• 5.4L/6.8L engine 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause [...]

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter . 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil l[...]

Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine nois[...]

Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery , excessive pressure on the end wa[...]

6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more to relearn the idle and fuel trim strategy . • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. If the battery has b[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “COLD FILL RANGE” in the coolant reservoir . • Refer to the scheduled maintenance information for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter . If [...]

Note: Use of Motorcraft Cooling System Stop Leak Pellets may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan. • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Specialty Orange Engine Coolant meeting Ford specification WSS-M97B44–D, or DEX-COOL 威 brand with the factory-filled coo[...]

3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (see above), to within the “COLD FILL RANGE” on the reservoir . 6. Replace the cap. T urn until tightly install[...]

Severe climates If you drive in extremely cold climates (less than –34°F [–36°C ]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant a[...]

How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The message center will indicate the engine is overheating. • The Check engine indicator ( ) will illuminate. If the engine reaches a preset over -temperature condition, the engine will automatically switch t[...]

Driving the vehicle without repairing the engine problem increases the chance of engine damage. T ake your vehicle to a service facility as soon as possible. FUEL FILTER For fuel filter replacement, see your authorized dealer . Refer to the scheduled maintenance information for the appropriate intervals for changing the fuel filter . Replace the fu[...]

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injur[...]

Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling. • DO NOT use a device that would h[...]

If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The vehicle warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you [...]

Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly . However , if it knock[...]

If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. • Normally , adding one gallon of fuel is enough to restart the engine. If the vehicle is [...]

• Use the same filling rate setting (low-medium-high) each time the tank is filled. • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction[...]

• Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy . • Slow down gradually . • Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h[...]

• Using fuel blended with alcohol may lower fuel economy . • Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • T ransmissions give their best fuel economy when operated in the top cruise ge[...]

emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability . Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the Check engine light ( ), c[...]

4. Driving through deep water - the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tightening the fuel cap or letting the electrical system dry out. After three driving cycles without these or any other temporary malfunctions present, the indicator should stay of[...]

• Gasoline engine shown; diesel engine similar . Refer to Identifying components in the engine compartment in the 6.0/6.4 Liter Power Stroke Direct Injection T urbo Diesel Owner Guide Supplement. Check the fluid level when it is at ambient temperature, 20°F–80°F (-7°C–25°C): 1. Check the fluid level in the reservoir . It should be between[...]

BRAKE FLUID • V acuum boost system • Hydroboost system The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating ra[...]

Carefully read cautionary information on product label. For MEDICAL EMERGENCY INFORMA TION, contact a physician or Poison Control Center immediately; on Ford-Motorcraft products call: 1-800-959-3673 (FORD). Failure to follow these instructions may result in personal injury . During normal operation, the fluid level in the clutch reservoir should re[...]

4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary , refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remov[...]

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick handle and also in the Maintenance Product Specifications and Capacities section in this chapter . Use of a non-approved automatic transmission fluid may cause internal transmission [...]

Automatic transmission fluid filter (if equipped) The T orqShift automatic transmission may be equipped with a serviceable external fluid filter mounted under the transmission bell housing as shown in the illustration. T orqShift-equipped vehicles which do not have the externally mounted filter will have the transmission fluid filter located inside[...]

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Us[...]

T RANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to Maintenance Product Specifications and Capacities in this chapter . D[...]

The following procedure is for vehicles equipped with a gasoline engine. If your vehicle is equipped with a diesel engine, refer to the 6.0/6.4 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air [...]

5. Return air filter cover to original position making sure the four tabs are engaged and secure the three clamps. T ighten clamp on air tube and reconnect sensor . MOTORCRAFT PART NUMBERS Component 5.4L V8/6.8L V10 engines Air filter element F A-1883 Fuel filter FG-1011 Oil filter FL-820-S PCV valve 1 Battery (Standard) BXT -65-650 Battery (Option[...]

Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle, such as Motorcraft or equivalent replacement parts. The customer warranty may be void for any damage to the engine if such spark plugs are not used. 3 Also available with 6.4L diesel engine and T orqShift transmission. Part number is FT -176. 4 Als[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name Ford part number / Ford specification Front axle 5.8 pints (2.8L) Motorcraft SAE 80W -90 Premium Rear Axle Lubricant XY -80W -90–QL / WSP-M2C197–A Spindle bearing — High T emperature 4X4 Front Axle and Wheel Bearing Grease E8TZ-19590–A XG-11 (F AD) / ESA-M1C198?[...]

Item Capacity Ford part name Ford part number / Ford specification Engine coolant - 6.8L V10 engine 2 27.5 quarts (26.0L) Motorcraft Premium Gold Engine Coolant (yellow-colored) VC-7-B / WSS-M97B51-A1 Engine and fuel coolant - diesel engine Refer to the 6.0/6.4 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement Engine oil[...]

Item Capacity Ford part name Ford part number / Ford specification Hinges, latches, striker plates, fuel filler door hinge and seat tracks — Multi-Purpose Grease XG–4 or XL-5 / ESB-M1C93–B Lock cylinders — Motorcraft Penetrating and Lock Lubricant XL-1 / None T ransmission / parking brake linkages and pivots, brake and clutch pedal shaft (i[...]

Item Capacity Ford part name Ford part number / Ford specification W indshield washer fluid 3.5 quarts (3.3L) Motorcraft Premium W indshield W asher Concentrate ZC-32–A / WSB-M8B16–A2 1 Add 8 oz. (236 ml) of Additive Friction Modifier XL-3 or equivalent meeting Ford Specification EST -M2C118–A for complete refill of limited slip Ford axles. F[...]

ENGINE DATA Engine 5.4L V8 engine 6.8L V10 engine Cubic inches 330 415 Required fuel 87 octane 87 octane Firing order 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9 Spark plug gap 1.02–1.28mm (0.040–0.050 inch)* 1.02–1.28mm (0.040–0.050 inch)* Ignition system Coil on plug Coil on plug Compression ratio 9.8:1 9.2:1 *The 5.4L 3V and 6.8L 3V spark plug [...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

1. W orld manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSION/T RANSAXLE CODE DESIGNATIONS Y ou can find a transmission/transaxle code on the vehicle Safety Compliance Certification L[...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada authorized dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic [...]

Cargo organization and management T owing mirrors T railer hitches, wiring harnesses and accessories Peace of mind Mobile-ease 娂 hands-free communication system Remote start V ehicle security systems Wheel locks Not all accessories are available for all models. For maximum vehicle performance, keep the following information in mind when adding ac[...]

A Accessory delay .......................... 99 Air cleaner filter ............... 348–350 Air conditioning .......................... 75 Airbag supplemental restraint system ................................ 171–172 and child safety seats ............ 173 description .............................. 172 disposal ..................................[...]

Climate control (see Air conditioning or Heating) ............75 Clock adjust 6-CD in dash .............................31 AM/FM/CD ................................. 25 Clutch fluid .......................................... 342 operation while driving ..........244 recommended shift speeds .... 244 Compass, electronic set zone adjustment .........[...]

recommendations ................... 321 refill capacities ........................ 352 Exhaust fumes .......................... 234 F Fail safe cooling ........................ 328 Family entertainment system .... 43 Fluid capacities ......................... 352 Foglamps ..................................... 80 Four -Wheel Drive vehicles ....... 2[...]

lighting up panel and interior ....................................... 82 J Jump-starting your vehicle ......290 K Keyless entry system ............... 146 autolock ................................... 136 programming entry code ....... 146 Keys ........................................... 149 positions of the ignition ......... 231 L Lamps autolamp [...]

fluid, checking and adding .... 340 fluid, refill capacity ................ 352 Power W indows ........................... 98 Preparing to drive your vehicle ............................... 239 R Radio ................................22, 24, 30 Rear seat entertainment system .......................................... 43 Relays .....................[...]

label ......................................... 211 replacing .................................. 202 rotating .................................... 204 safety practices ....................... 203 sidewall information ............... 206 snow tires and chains ............ 211 spare tire ................................. 278 terminology .............[...]

367[...]

368[...]