Ford 2010 Expedition Bedienungsanleitung

Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 17 Message center 20 Entertainment Systems 39 How to get going 39 AM/FM stereo with CD 43 AM/FM stereo with in-dash six CD 51 Auxiliary input jack (Line in) 59 USB port 61 Rear seat controls 61 Satellite radio information 67 Family entertainment system 70 Navigation system 10[...]

Locks and Security 161 Keys 161 Locks 162 Anti-theft system 173 Seating and Safety Restraints 183 Seating 183 Safety restraints 204 Airbags 217 Child restraints 227 Tires, Wheels and Loading 246 T ire information 248 T ire inflation 251 T ire Pressure Monitoring System (TPMS) 263 V ehicle loading 268 T railer towing 275 Recreational towing 283 Driv[...]

Customer Assistance 352 Reporting safety defects (U.S. only) 358 Reporting safety defects (Canada only) 358 Cleaning 359 Maintenance and Specifications 368 Engine compartment 370 Engine oil 373 Battery 376 Engine coolant 378 Fuel information 384 Air filter(s) 398 Part numbers 401 Maintenance product specifications and capacities 402 Engine data 405[...]

CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the following [...]

W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubricatio[...]

Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage. SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’[...]

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly d[...]

T o access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful[...]

W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid - Non-Petroleum Based Parking Aid System Stability Control System[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Flu[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains [...]

chapter . If the light is blinking, engine misfire is occurring which could damage your catalytic converter . Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately by your authorized dealer . W ARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the cataly[...]

Airbag readiness: If this light fails to illuminate when the ignition is turned to on, continues to flash or remains on, have the system serviced immediately by your authorized dealer . A chime will sound when there is a malfunction in the indicator light. Safety belt: Reminds you to fasten your safety belt. A Belt-Minder 威 chime will also sound [...]

Low tire pressure warning (if equipped): Illuminates when your tire pressure is low . If the light remains on at start up or while driving, the tire pressure should be checked. Refer to Inflating your tires in the T ires, Wheels and Loading chapter . When the ignition is first turned to on, the light will illuminate for three seconds to ensure the [...]

4X2 (R TT) (if equipped): Displays momentarily when two-wheel drive high is selected. If the light fails to display when the ignition is turned on, or remains on, have the system serviced immediately by your authorized dealer . Four wheel drive low (R TT) (if equipped): Displays when four -wheel drive low is engaged. If the light fails to display w[...]

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’ s door is opened. Parking brake on warning chime: Sounds when the parking brake is set, the engine is running and the vehicle is driven more than 3 mph (5 km/h). T urn signal chime: Sounds when the tu[...]

Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. W ARNING: Never remove the[...]

T achometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Battery voltage gauge: Indicates the battery voltage when the ignition is in the on position. If the pointer moves and stays outside the normal operating range, have the vehicle’ s ele[...]

STANDARD MESSAGE CENTER (IF EQUIPPED) Y our vehicle’ s message center is capable of monitoring many vehicle systems and will alert you to potential vehicle problems and various conditions with an informational message followed by a long indicator chime. The message center display is located in the instrument cluster . Selectable features (informa[...]

If you calculate your average fuel economy by dividing distance traveled by gallons of fuel used (liters of fuel used by 100 kilometers traveled), your figure may be different than displayed for the following reasons: • Y our vehicle was not perfectly level during fill-up • Differences in the automatic shut-off points on the fuel pumps at servi[...]

1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Press and release the SELECT/RESET stem to scroll through the information menu until the message center displays HOLD RESET FOR SETUP MENU. 3. Press and hold the SELECT/RESET stem until the message center displays HOLD RESET FOR SYSTEM CHECK. D[...]

5. Press and hold the SELECT/RESET stem until the message center displays CIRCLE SLOWL Y TO CALIBRA TE. This step may require up to five circles to complete the calibration. NOTE: If the SELECT/RESET stem is pressed during the calibration or three minutes has elapsed since the beginning of the calibration without driving the vehicle, the message ce[...]

OIL LIFE This displays the remaining oil life. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONL Y RECOMMENDED ENGINE OILS. T o reset the oil monitoring system to 100% after each oil change (approximately 7,500 miles [12,000 km] or 12 months) perform the following: 1. P[...]

AUTOUNLOCK This feature automatically unlocks all vehicle doors when the driver’ s door is opened within 10 minutes of the ignition being turned off. Press the RESET control to turn autounlock on or off. TRAILER SW A Y (if equipped) This feature uses the electronic stability control to mitigate trailer sway , Press the RESET control to turn trail[...]

• Some messages will reappear after clearing or being reset if a problem or condition is still present and needs your attention. • Some messages can be acknowledged and reset by pressing the SELECT/RESET stem. This allows you to use the full message center functionality by clearing the message. DOOR AJAR — Displayed when a door is not complet[...]

FOR 4X4 LOW SLOW TO 3 MPH (if equipped) — Displayed when 4X4 LOW is selected while the vehicle is moving. For more information, refer to Control trac four -wheel drive (4X4) operation in the Driving chapter . FOR 4X4 LOW SHIFT TO N (if equipped) — Displayed when 4X4 LOW is selected and the vehicle is stopped. For more information, refer to Cont[...]

KEY COULD NOT PROGRAM — Displayed when an attempt is made to program a spare key using two existing MyKeys. Refer to MyKey™ in the Locks and Security chapter for more information. VEHICLE SPEED 80 MPH MAX — Displayed when a MyKey™ is in use and the Admin has enabled the MyKey speed limit and the vehicle speed is 80 mph (130 km/h). Refer to [...]

Info Press the INFO button repeatedly to cycle through the following features: TRIP A/B Registers the distance of individual journeys. Press and release INFO button until the A or B trip appears in the display (this represents the trip mode). Press and hold the RESET button to reset. Refer to UNITS later in this section to switch the display from M[...]

A VG MPG (L/100km) A verage fuel economy displays your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing distance traveled by gallons of fuel used (liters of fuel used by 100 kilometers traveled), your figure may be different than displayed for the following reasons: • Y our vehicle was [...]

System check and vehicle feature customization Press the SETUP button repeatedly to cycle the message center through the following features: RESET FOR SYSTEM CHECK When this message appears, press the RESET button and the message center will begin to cycle through the following systems and provide a status of the item if needed. Note: Some systems [...]

Note: T o change oil life 100% miles value from 7,500 miles (12,000 km) or 12 months to another value, proceed to Step 3. 3. Once “OIL LIFE SET TO XXX%” is displayed, release and press the RESET button to change the Oil Life Start V alue. Each release and press will reduce the value by 10%. Note: Oil life start value of 100% equals 7,500 miles [...]

Press the RESET button to turn autounlock on or off. RUNNING BOARDS (if equipped) This feature automatically deploys the side running boards for easy entry/exit from the vehicle or for cleaning. Press the RESET button to select the running boards setting as follows: • AUTO: the running boards will automatically deploy when a door is opened and au[...]

Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error . Do the following to set the proper zone: Compass zone/[...]

CREA TE MYKEY / MYKEY SETUP / CLEAR MYKEY For more information refer to MyKey™ in the Locks and Security chapter . ENGLISH / FRENCH / SP ANISH RESET FOR NEW Allows you to choose which language the message center will display in. Selectable languages are English, Spanish, or French. Press RESET to cycle through each of the language choices. Press [...]

CHECK CHARGING SYSTEM — Displayed when the electrical system is not maintaining proper voltage when the engine is running. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal sp[...]

CHECK AIR SUSPENSION (if equipped) — Displayed when the air suspension system is not operating properly . If this message is displayed while driving, pull off the road as soon as safely possible. For more information, refer to Air suspension system in the Driving chapter . CHECK P ARK AID (if equipped) — Displayed when the transmission is in R [...]

MY KEY ACTIVE DRIVE SAFEL Y — Displayed at startup when MyKey™ is in use. Refer to MyKey™ in the Locks and Security chapter for more information. KEY COULD NOT PROGRAM — Displayed when an attempt is made to program a spare key using two existing MyKeys. Refer to MyKey™ in the Locks and Security chapter for more information. VEHICLE SPEED [...]

AUDIO SYSTEMS Note: If your volume is muted and MYKEY VOLUME LIMITED is displayed, refer to MyKey™ in the Locks and Security chapter for more information. Quick start — How to get going W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when u[...]

4. Once you are tuned to the desired station, press and hold a memory preset (1–6) to save the station. PRESET SA VED will appear on the display and the sound will return signifying the station has been saved. Y ou can save up to six stations in each frequency band — six in AM, six in FM1 and six in FM2. T o access your saved stations, press th[...]

Listening to a CD/MP3 (if equipped) 1. If the audio system is turned off, press VOL-PUSH to turn the radio on. T urn VOL-PUSH to adjust the volume. Note: The system may take a few moments to turn on. 2. Press CD to enter CD mode. If a disc is already loaded into the system, CD play will begin where it ended last. For a single CD system, if a disc i[...]

Press and hold REW to manually reverse in a CD/MP3 track. Press and hold FF to manually advance in a CD/MP3 track. While in folder mode, press FOLDER to access the previous folder on MP3 discs, if available. While in folder mode, press FOLDER to access the next folder on MP3 discs, if available. Press SHUFFLE to engage shuffle mode. SHUFFLE ON will[...]

AM/FM single CD/MP3 satellite compatible sound system (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of th[...]

Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer for availability . 2. (Phone): Press to access SYNC 威 phone features if your vehicle is equipped with SYNC 威 . Refer to the SYNC 威 supplement for more information. If your vehicle is not equipped with SYNC 威 , the display will read NO[...]

• DELETE SONG: Press OK to delete a song from the system’ s memory . Press / to cycle through the saved songs. When the song appears in the display that you would like to delete, press OK. The song will appear in the display for confirmation. Press OK again and the display will read SONG DELETED. If you do not want to delete the currently liste[...]

RBDS: A vailable only in FM mode. This feature allows you to display text transmitted by RBDS-equipped stations and to search for a certain category of music format: CLASSIC, COUNTRY , INFORM, JAZZ/RB, ROCK, etc. T o activate, press MENU repeatedly until RBDS (ON/OFF) appears in the display . Use / / SEEK to toggle RBDS ON/OFF . (When RBDS is OFF ,[...]

Adjust 1–7: Increasing this setting from 1 (lowest setting) to 7 (highest setting) allows the radio volume to automatically change slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3; SPEED OFF turns the feature off and level 7 is the maximum setting. T rack/Folder mode: A vailable only on MP3 discs in CD[...]

In satellite radio mode (if equipped), press SEEK, SEEK to seek to the previous/next channel. In CA TEGOR Y MODE, press SEEK, SEEK to select a category (Jazz, Rock, News, etc.). Once the desired category is in the display , press SEEK, SEEK to seek to the previous/next channel in the selected category . Press and hold SEEK, SEEK to fast seek throug[...]

9. FOLDER: In folder mode, press FOLDER to access the previous folder on MP3 discs, if available. 10. FF (Fast forward): In CD mode, press FF to manually advance in a track. In DVD mode (if equipped), press and hold to advance through the current chapter . 11. REW (Rewind): In CD mode, press REW to manually reverse in a track. In DVD mode (if equip[...]

In satellite radio mode (if equipped), press and release to enter TEXT MODE and display the current song title. While in TEXT MODE, press again to scroll through the current song title, artist, channel category and the SIRIUS long channel name. Press and hold to hear a brief sampling of the next channels. Press again to stop. In CA TEGOR Y MODE, pr[...]

Premium AM/FM in-dash six CD/MP3 satellite compatible sound system (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe op[...]

Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer for availability . 2. (Phone): Press to access SYNC 威 phone features if your vehicle is equipped. Refer to the SYNC 威 supplement for more information. If your vehicle is not equipped with SYNC 威 , the display will read NO PHONE. 3. MENU[...]

• DELETE SONG: Press OK to delete a song from the system’ s memory . Press / to cycle through the saved songs. When the song appears in the display that you would like to delete, press OK. The song will appear in the display for confirmation. Press OK again and the display will read SONG DELETED. If you do not want to delete the currently liste[...]

T o activate, press MENU repeatedly until RBDS (ON/OFF) appears in the display . Use / / SEEK to toggle RBDS ON/OFF . (When RBDS is OFF , you will not be able to search for RBDS equipped stations or view the station name or type.) T o search for specific RBDS music categories: When the desired category appears in the display , press / to find the d[...]

Recommended level is 1–3; SPEED OFF turns the feature off and level 7 is the maximum setting. T rack/Folder Mode: A vailable only on MP3 discs in CD mode. In T rack Mode, pressing SEEK will scroll through all tracks on the disc. In Folder mode, pressing SEEK will scroll only through tracks within the selected folder . Press FOLDER, FOLDER to acce[...]

In CA TEGOR Y MODE, press / to select a specific category (Jazz, Rock, News, etc.). Once the desired category is in the display , press SEEK, SEEK to seek to the previous/next channel in the selected category . Press and hold SCAN for a brief sampling of all channels in the selected category . In TEXT MODE, press SEEK, SEEK to view the previous/add[...]

10. FF (Fast forward): In CD mode, press FF to manually advance in a track. In DVD mode (if equipped), press to advance within the current chapter . 11. REW (Rewind): In radio mode, press REW to manually reverse in a track. In DVD mode (if equipped), press to reverse within the current chapter . 12. Memory presets: T o set a station, select the des[...]

14. AM/FM: Press to select AM/FM1/FM2 frequency band. 15. ON/OFF/V olume: Press to turn ON/OFF . T urn to increase/decrease volume. Note: If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. 16. CD: Press to enter CD/MP3[...]

19. CD slot: Insert a CD label side up. Auxiliary input jack (Line in) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of[...]

2. Ensure that the battery in your portable music player is new or fully charged and that the device is turned off. 3. Attach one end of the audio extension cable to the headphone output of your player and the other end of the audio extension cable to the AIJ in your vehicle. 4. T urn the radio on, using either a tuned FM station or a CD loaded int[...]

USB port (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle. Only use cell phones and other d[...]

1. MEDIA: Push repeatedly to cycle through available playing medias such as AM, FM1, FM2, CD, SA T1, SA T2, SA T3 (satellite radio if equipped), DVD (if equipped) and SYNC 威 (if equipped). If in Dual Play mode, SHARED illuminates in the radio display when the front and rear modes are set to the same media. Note: After pressing the media button to[...]

Parental control Press the memory preset controls 3 and 5 simultaneously on the front audio controls to disable the rear seat controls. They will remain disabled until the front seat passengers “enable” them again by simultaneously pressing the 3 and 5 preset controls. The settings of the front seat controls will always override those of the re[...]

Using headphones/Dual Play mode W ARNING: Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may become entangled in the cords and seriously injure themselves. Plug a 3.5 mm headphone (not included) into the jack. Press the speake[...]

CD/CD player care Do: • Handle discs by their edges only . (Never touch the playing surface). • Inspect discs before playing. • Clean only with an approved CD cleaner . • W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are[...]

CDs with homemade paper (adhesive) labels should not be inserted into the CD player as the label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. Audio[...]

Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extension will be played. Other files will be ignored by the system. This enables you to use the same MP3 d[...]

• T errain: Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception. • Station overload: When you pass a ground based broadcast repeating tower , a stronger signal may overtake a weaker one and result in an audio mute. Unlike AM/FM audible st[...]

Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly . SA T F AUL T Internal module or system failure present. If this message does not clear within a short period of time, or with an ignition key cycle, your receiv[...]

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly . NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly . NO SIGNAL Loss of sign[...]

Y our vehicle may be equipped with a Family Entertainment System (FES) which allows you to listen to audio CDs, MP3 discs, watch DVDs and to plug in and play a variety of standard video game systems. The DVD player is capable of playing standard DVDs, CDs, MP3s and is compatible with CD-R/W , CD-R and certain CD-ROM media. Please review this materi[...]

Note (navigation-based radio systems only): W h e nad i s ci s inserted, the FES switches to dual-play mode–rear speakers turn off, and headphones turn on. T o switch back to all four speakers on, press the headphone button. Press VIDEO to change the source displayed on the screen. Press repeatedly to cycle through: DVD-DISC, DVD-AUX, NON-DVD, OF[...]

Note (navigation-based radio systems only): W h e nad i s ci s inserted, the FES switches to dual-play mode–rear speakers turn off, and headphones turn on. T o switch back to all four speakers on, press the headphone button. T o play an MP3 disc in the DVD system: 1. Ensure that the vehicle is on or the ignition is in accessory mode. 2. Insert an[...]

3. Connect an auxiliary audio/video source by connecting RCA cords (not included) to the RCA jacks on the left hand side of the system. • Y ellow (1) — video input • White (2) — left channel audio input • Red (3) — right channel audio input 4. Press MEDIA on the DVD system to change the media source to AUX. 5. Press VIDEO on the DVD sys[...]

4. Press MEDIA to change the audio source of the active channel (A or B). The audio source will be shown on the display . Y ou may change the active channel by pressing the A or B headphone control button. Note: Channel A can access any possible media source (AM, FM1, FM2, SA T (if equipped), CD, DVD, AUX). Channel B can only access DVD and AUX sou[...]

Using wired headphones (not included): W ARNING: Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may become entangled in the cords and seriously injure themselves. 1. Connect the wired headphones in to the headphone jacks on ei[...]

DVD player controls 1. Headphone control A/B: While in Dual Play mode, press to select either the A or B headphone source. Then press MEDIA to select the desired playing media for that headset. When a headphone channel has been selected (A or B), selections will affect the source on that channel only . Note: Headphone A can access any possible medi[...]

4. (Fast forward): Press and release for the next chapter or track. Press and hold to forward search a DVD, Video CD, or FES CD in DVD/CD mode. 5. / (Play/Pause): Press (Play) to select DVD mode (and to turn the DVD system on if it is off). If a disc is present, it will resume or begin to play . Press (Pause) while playing a disc to pause a DVD or [...]

11. / (Headphones/Speakers): Press once for Dual Play (Headphone mode- the rear speakers are muted) and press again for Single Play (same media playing through all speakers). Y ou can also press the 2 and 4 memory preset buttons on the audio system at the same time to perform the same function. For further interaction information, refer to Single P[...]

Remote control Unless otherwise stated, all operations can be carried out with the remote control. Always point the remote control directly at the player . Ensure that there are no obstructions between the remote and player . 1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF . 2. Cursor controls: Use in various active men[...]

7. VOL (V olume): When in Single Play , press to increase ( )o r decrease ( ) the volume over all speakers. When in Dual Play , press to increase ( ) or decrease ( ) the volume for the wired headphones. (W ireless headphone volume is controlled with the rotary dial on the right ear piece.) 8. Fast Forward/Next: In DVD mode, press and hold for a qui[...]

21. LANGUAGE (DVD dependent): Press to select the desired language. 22. ENTER: Press to select the highlighted menu option. 23. ILLUMINA TION : Press to illuminate the remote control and backlight all of the buttons. Battery replacement Batteries are supplied with the remote control unit. Since all batteries have a limited shelf life, replace them [...]

Headphones Wireless headphones W ARNING: The driver should never use the headphones while driving the vehicle. Using headphones may prevent the driver from hearing audible warnings such as horns or emergency sirens, which could result in a crash causing serious injury . Give your full attention to driving and to the road. Y our FES system is equipp[...]

T o install the batteries, remove the screw at the bottom of the cover . Then, lightly press down on top and slide the cover off. When replacing the batteries, use two new batteries (alkaline recommended) and install them with the correct orientation as indicated in the battery housing. Entertainment Systems 84 2010 Expedition (exd) Owners Guide (o[...]

T o operate the headphones: • Press POWER on the ear piece to turn on the headphones. A red indicator light will illuminate indicating the headphones are ON. Press POWER again to turn the headphones off. • Adjust the headphones to comfortably fit your head using the headband adjustment. • Select the desired audio source (Channel A or B) for e[...]

Wired headphones W ARNING: Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may become entangled in the cords and seriously injure themselves. W ARNING: The driver should never use the headphones while driving the vehicle. Using[...]

Single Play: Single play consists of all occupants in the vehicle listening to the same playing media over the front and rear speakers. When the DVD system is on, and the same source is playing through the front and rear speakers, SINGLE PLA Y will appear in the front radio display . Dual Play (navigation-based radio systems only): Dual play is whe[...]

Press the Headphone Control button A to change the audio source for Channel A. Press MEDIA to change the audio source for Channel A. This information will display on the DVD system screen. Press the Headphone Control button B to change the audio source for Channel B. Press MEDIA to change the audio source for Channel B. This information will displa[...]

Press the Headphone Control button A to change the audio source for Channel A. Press MEDIA to change the audio source for Channel A. This information will display on the DVD system screen. Press the Headphone Control button B to change the audio source for Channel B. Press MEDIA to change the audio source for Channel B. This information will displa[...]

Menu mode Press MENU once on the DVD system to access the DVD disc menu if available. Press MENU twice to access the DVD set-up menu and the following features: 1. ZOOM 2. ANGLE 3. ASPECT RA TIO 4. LANGUAGE 5. SUB TITLES Angle mode Select ANGLE to select various angles of view for the DVD. This is disc dependent — some DVD discs may have more vie[...]

Y ou can select from: WIDE, LETTER BOX or P AN SCAN. Once you have made your selection, press ENTER to confirm. The LCD screen display will immediately change to your selection after the system resumes playback of the DVD. The system default is WIDE (16:9). Language Select LANGUAGE to select the language you would like to use for audio output (Engl[...]

Once you have made your selection, press ENTER to confirm. This is disc dependent. Audio CDs T o play audio CDs on your DVD system: 1. Ensure that the vehicle is on or the ignition is in accessory mode. 2. Ensure that the DVD system is on. 3. Insert an audio CD into the DVD system, label side up. 4. The track and elapsed time will appear in the sta[...]

4. The folder , track and elapsed time will appear in the status bar . The screen will list the Artist, T itle, Album and File Name. COMP (Compression): Compression brings soft and loud CD/MP3 passages together for a more consistent listening level when in CD mode. Press to turn the feature on/off. SHUFFLE: Press to hear all tracks on the current M[...]

CD, MP3 and CD player care • Handle discs by their edges only . Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended periods of time. • Do not insert more than one disc into the slot of the CD player (if equipped). • Always store discs out of direct sunlight. Excessive heat may damage or war[...]

Playing a DVD 1. Ensure that the vehicle is on or the ignition is in accessory mode. 2. Ensure that the navigation system is on. 3. Insert a DVD label-side up into the system. 4. Use the DVD bezel controls to: Press to play or pause a DVD. Press to stop or eject a DVD. Press and release to go to the previous chapter . Press and hold for a fast reve[...]

Frame by frame 1. W ith a DVD playing, press pause. 2. Press the right cursor button. The DVD will advance one frame. Each press of the right cursor button will advance the DVD video by one frame. Headphone/auxiliary jacks There are wired headphones (not included) and auxiliary jacks on the left and right side of your DVD system. They can be used t[...]

The B headphone jack (5) is located on the right side of the DVD system. Plug in wired headphones (not included) here. Note: The B headphones can only access DVD and AUX modes. They cannot access radio sources. Audio displays Y our DVD system interacts closely with the front audio system. Status messages will appear in the radio display showing the[...]

There are three levels of control of the FES buttons. The states are FULL (enabled), LOCAL or LOCKED (disabled). T o change the level of control, press the memory preset controls 3 and 5 simultaneously on the front audio controls. The control level will cycle each time the buttons are pressed simultaneously . The three states are described as: FULL[...]

rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. MP3: Supply of this product only conveys a license for private, non-commercia[...]

W ARNING: The driver should not attempt to operate any function of the DVD system while the vehicle is in motion. Give full attention to driving and to the road. Pull off the road in a safe place before inserting or extracting DVDs from the system. A remote control is included in the system to allow the rear seat occupants to operate the FES functi[...]

Care and service of the DVD player Environmental extremes DVD players which are subjected to harsh environmental conditions may be damaged or perform at less than maximum capability . T o avoid these outcomes, whenever possible avoid exposing your DVD player to: • extremely hot or cold temperatures. • direct sunlight. • high humidity . • a [...]

Cleaning DVD and CD discs Inspect all discs for contamination before playing. If necessary , clean discs only with an approved DVD and CD cleaner and wipe from the center out to the edge. Do not use circular motion. Compatibility with aftermarket audio systems (headphone only mode) When the Family Entertainment System (FES) detects that the origina[...]

MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. T emperature selection: Controls the temperature of the airflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recirculated air through the instrument panel vents [...]

6. Fan speed adjustment: Controls the volume of air circulated in the vehicle. Manual heating and air conditioning system with rear passenger compartment climate control (if equipped) 1. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recircul[...]

4. REAR Rear temperature control: Press to enable the auxiliary system and to set the desired rear cabin airflow temperature with the front control. The rear cabin airflow temperature will match the driver airflow temperature setting when only the center rear temperature light ( REAR ) is illuminated. The rear cabin airflow temperature will be warm[...]

• During extreme high ambient temperatures when idling stationary for extended periods of time in gear , it is recommended to run the A/C in the MAX A/C position, turn off the rear A/C unit, reduce blower fan speed from the highest setting and put the vehicle’ s transmission into the P (Park) position to continue to receive cool air from your A[...]

2. Rear temperature control: Press to enable the auxiliary system and set the desired rear cabin airflow temperature with the front control. The rear cabin airflow temperature will match the driver airflow temperature setting when only the center rear temperature bar is illuminated. The rear cabin airflow temperature will be warmer or cooler than t[...]

12. Manual override controls: Allows you to manually select where airflow is distributed. T o return to full automatic control, press AUTO. 13. F Front fan speed control: Press to manually increase or decrease the fan speed. T o return to full automatic control, press AUTO. 14. OFF: Outside air is shut out and the climate system is turned off. 15. [...]

Dual automatic temperature control with heated and cooled seats and rear passenger compartment climate control (if equipped) 1. Defrost: Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear thin ice or fog from the windshield. 2. Rear temperature control: Press to enable the auxiliary system and se[...]

5. R Rear fan speed control: Press to enable the auxiliary system or to adjust the rear fan speed from the front control. Press to manually increase or decrease the fan speed. When the rear fan button is pressed, the display will show only the rear cabin settings. After the rear setting changes are completed on the front control, the display will a[...]

14. Driver temperature control: Press to increase or decrease the temperature on the driver side of the cabin. Sets the passenger side temperature also when DUAL is disengaged. Note: The recommended vehicle cabin setting is between 72°F (22°C) and 75°F (24°C). 15. AUTO: Press to engage full automatic operation, and select the desired temperatur[...]

• For maximum cooling performance, (MAX A/C): In AUTO: Press AUTO control and set to desired temperature. In Manual Override: Press the (panel), A/C, and recirculated air , set the temperature to 60°F (16°C) and the fan to the highest blower setting. • Do not put objects under the front seats that will interfere with the airflow to the back s[...]

REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel and works to clear the rear window of fog and thin ice. The engine must be running to operate the rear window defroster . Press the control to turn the rear window defroster on. An indicator light on the button will illuminate when active. The rear window def[...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Rotate back to to turn the headlamps off. Autolamp control The autolamp system provides light sensitive automatic on/off control of the exterior lights normally controlled by the headlamp control. [...]

Fog lamp control (if equipped) The headlamp control also operates the fog lamps. The fog lamps can be turned on when the headlamp control is in the , or positions and the high beams are not turned on. Pull the headlamp control towards you to turn the fog lamps on. The fog lamp indicator light will illuminate. High beams Push the lever toward the in[...]

W ARNING: Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. P ANEL DIMMER CONTROL Use to ad[...]

1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away . • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp (indicated by a 3.0 mm circle on the lens) t[...]

TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Front row map lamps (if equipped) T o turn on the map lamps, press the outer edge of the clear lens. The front row map lamp lights when: • any door is opened. • the instrument panel dimmer switch is rotated until the[...]

Second row map lamps (if equipped) The second row map lamps are located in the headliner above the second row seats. The second row map lamp lights when: • any door is opened, • the instrument panel dimmer switch is rotated up until the courtesy lamps come on, and • any of the remote entry controls are pressed and the ignition is off. Press t[...]

BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a thin [...]

Function Number of bulbs T rade number Headlamps (low and high-beam) 2 H13/9008 Front sidemarker 2 194 Front park/turn lamps 2 3157 A Fog lamps 2 9145 Front row map lamps 2 W5W Front row map/dome lamps 3 578 Rear cargo lamp 1 578 2nd row reading lamp 2 W5W T urn/tail/brake/sidemarker lamps 2 3157K or 4157K Backup lamp 2 921 Approach/mirror turn sig[...]

Replacing headlamp bulbs 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. At the back of the headlamp, remove the two headlamp assembly retainer bolts. 4. Slide headlamp assembly forward and off the retaining tab to expose the back of the bulb and electrical connector . 5. Disconnect the electrical connector . 6. [...]

Replacing front parking lamp/turn/sidemarker signal bulbs 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. At the back of the headlamp, remove the two headlamp assembly retainer bolts. 4. Slide headlamp assembly forward and off the retaining tab to expose the back of the headlamp assembly . 5. Rotate the bulb sock[...]

4. Rotate the bulb socket counterclockwise and remove from lamp assembly . 5. Pull bulb straight out of socket and snap in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. 7. Carefully install the tail lamp assembly on the vehicle by securing the lamp assembly with two torx screws. Replacing the high-mount brake[...]

Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assembly on the liftgate. T o change the license plate bulbs: 1. Make sure the headlamp switch is in the off position. 2. Remove the license lamp screw from the assembly . 3. Pull the lamp down and twist the bulb socket counterclockwise. Remove the bu[...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Speed dependent wipers: When the wiper control is on, the speed of the wipers will automatically adjust with the vehicle speed. The faster your vehicle is travelling the fas[...]

Courtesy wipe feature: One extra wipe will occur a few seconds after washing the front window to clear any excess washer fluid remaining on the windshield. Note: Do not operate the washer when the washer reservoir is empty . This may cause the washer pump to overheat. Check the washer fluid level frequently . Do not operate the wipers when the wind[...]

TILT STEERING WHEEL 1. Pull and hold the steering wheel release control toward you. 2. Move the steering up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position. W ARNING: Never adjust the steering column when the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQU[...]

OVERHEAD CONSOLE The appearance of your vehicle’ s overhead console will vary according to your option package. Forward storage bin (if equipped) The storage compartment may be used to store a pair of sunglasses. Press the release area on the rear edge of the bin door to open the storage compartment. The door will open to full open position. Conv[...]

Power quarter rear windows (if equipped) Press the VENT portion of the control to open the power rear quarter windows. Pull the VENT control to close the power rear quarter windows. Note: V ehicles without a moonroof, will only have the VENT button. W ARNING: Do not leave children unattended in the vehicle and do not let children play with the powe[...]

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . Auxiliary powe[...]

POWER WINDOWS W ARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. W ARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and p[...]

T o operate one-touch up: • Pull the switch completely up to the second detent and release quickly . The window will close fully . Momentarily press the switch to any position to stop the window operation. If the switch is pressed and held to the normal open or one-touch down position during a one-touch up event, the window will stop. If, after 1[...]

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support arm which lets you adjust the mirror up or down and from side to side. W ARNING: Do not adjust the mirror while the vehicle is in motion. Automatic dimming interior rear view mirror Y our vehicle is equipped with an interior rear view mirror which has an auto-dimming [...]

EXTERIOR MIRRORS Power side view mirrors The ignition can be in any position to adjust the power side view mirrors. T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror . 2. Move the control in the direction you wish to tilt the mirror . 3. Return to th[...]

Note: 10 or more switch activations within one minute, or repeated folding/unfolding of the mirrors while holding the switch rearward during full travel, may cause the system to disable the fold/unfold function to protect motors from overheating. Should this occur , wait approximately three minutes with the vehicle running and up to 10 minutes with[...]

W ARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. POWER DEPLOYABLE RUNNING BOARDS (IF EQUIPPED) Deployable running boards (DRB) automatically move when the doors are opened to assist entering and exiting the vehicle. Automatic power deploy: • The running boards will extend down and out whe[...]

Note: The running boards may operate slower in cooler temperatures. In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running board mechanism, possibly leading to unwanted noise. If this occurs, manually set the running boards to the deployed position and flush the system (in particular the front and rear hinge arm[...]

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. No[...]

Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. Y ou can also use the SET [...]

Turning of f speed control There are two ways to turn off the speed control: • Press the brake pedal. This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) T[...]

In CD mode (if equipped): • Press SEEK to select the next selection on the CD/USB or press and hold to forward or reverse through the CD/USB. In DVD mode (if equipped): • Refer to the Family entertainment DVD system in the Entertainment Systems chapter . In any mode: • Press VOL + or − to adjust volume. Navigation system hands free control [...]

Press to activate phone mode or answer a phone call. Press and hold to end call or exit phone mode. Press to scroll through various menus and selections. Press OK to confirm your selection. For further information on the SYNC 威 system, refer to the SYNC 威 supplement. Navigation system/SYNC 威 hands free control features (if equipped) Press VOI[...]

W ARNING: When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the moon roof opening. T o close the moon roof: Pull and release the SLIDE control, the moon roof will close automatically . Press the switch again to stop the moon roof. Bounce-back: When an obsta[...]

Car2U 威 Home Automation System HomeLink 姞 Wireless Control System (if equipped) The HomeLink 威 W ireless Control System, located on the driver’ s visor , provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate gar[...]

Programming Do not program HomeLink 威 with the vehicle parked in the garage. Note: Y our vehicle may require the ignition switch to be turned to the accessory position for programming and/or operation of the HomeLink 威 . It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink ?[...]

press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink 威 should now activate your rolling code equipped device. T o program additional HomeLink 威 buttons begin with Step 1 in this section. For questio[...]

Erasing HomeLink 姞 buttons T o erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink 威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. HomeLink 威 is now in the train (or learning) mode and can be prog[...]

W ARNING: Make sure that people and objects are clear of the garage door or security device you are programming. Do not program the Car2U 威 system with the vehicle in the garage. Do not use the Car2U 威 system with any garage door opener that lacks safety stop and reverse features as required by U.S. Federal Safety Standards (this includes any g[...]

If you do not know if your garage door opener is a rolling code or fixed code device, open your garage door opener’ s remote control battery cover . If a panel of DIP switches is present your garage door opener is a fixed code device. If not, your garage door opener is a rolling code device. Rolling code programming Note: Programming the rolling [...]

2. Go to the garage to locate the garage door opener motor and its “learn” button. Y ou may need a ladder to reach the unit and you may need to remove the unit’ s cover or light lens to locate the “learn” button. Press the “learn” button, after which you will have 10–30 seconds to return to your vehicle and complete the following st[...]

Note: The Car2U 威 system allows for three devices to be programmed. If you need to change or replace any of the three devices after it has been initially programmed, it is necessary to erase the current settings using the Erasing the Car2U 威 Home Automation System buttons procedure and then programming all of the devices being used. Fixed code [...]

3. T o input these positions into the Car2U 威 system, simultaneously press all three Car2U 威 system buttons for a few seconds and then release to put the device into programming mode. The indicator lights will blink slowly . Within 2.5 minutes enter your corresponding DIP switch settings from left to right into your Car2U 威 system by pressing[...]

T o erase programming on the Car2U 威 system (individual buttons cannot be erased), use the following procedure: 1. Firmly press the two outside Car2U 威 system buttons simultaneously for approximately 20 seconds until the indicator lights begin to blink rapidly . The indicator lights are located directly above the buttons. 2. Once the indicator [...]

W ARNING: Keep keys out of reach of children. Do not allow children to play near an open or moving power liftgate. The liftgate will only operate with the vehicle in P (Park). The chime will beep once if conditions are not correct to start an operation. These conditions include: • The ignition is in on and the transmission is not in P (Park) • [...]

T o open the liftgate with outside liftgate control button (manual actuation): 1. Unlock the liftgate with the remote entry transmitter or power door unlock control. 2. Press the control button located in the top of the liftgate pull cup handle. Note: For the best performance allow the power system to open the liftgate after releasing the control b[...]

Note: In case of operation in extreme cold -40°F (-40°C), or on extreme inclines, manual operation of the liftgate is suggested. Obstacle detection The power liftgate system is equipped with an obstacle detection feature. If the power liftgate is closing, the system is designed to reverse to full open when it encounters a solid obstacle. A three [...]

Liftgate window T o open the liftgate window , press the button on the left side of the liftgate above the license plate. MANUAL LIFTGATE (IF EQUIPPED) The liftgate area is only intended for cargo, not passengers. Y ou can open and close the liftgate from outside the vehicle. The liftgate cannot be opened from the cargo area control button, only cl[...]

CARGO MANAGEMENT SYSTEM (IF EQUIPPED) The cargo management system consists of a storage compartment located in the floor of the rear cargo area. 1. T o open, lift up on the handle and cover . 2. T o close, lower the cover and press down on the handle until the latch clicks. Cargo shelf/divider (if equipped) The cargo shelf/divider is located behind[...]

W ARNING: Do not load any objects on the shelf that may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. W ARNING: Do not place people or pets on or under the parcel shelf. LUGGAGE RACK Y our vehicle is equipped with a roof rack for transporting items on the exterior of the vehicle. The maximum reco[...]

KEYS Y our vehicle may be equipped with two Integrated Keyhead T ransmitters (IKT s). The key blade functions as a programmed key which starts the vehicle and unlocks/locks all the doors. The transmitter portion functions as the remote entry transmitter . Y our IKT s are programmed to your vehicle; using a non-programmed key will not permit your ve[...]

POWER DOOR LOCKS Press control to unlock all doors. Press control to lock all doors. Smart locks This feature helps to prevent you from locking yourself out of the vehicle if your key is still in the ignition. When you open one of the front doors or the liftgate and you lock the vehicle with the power door lock control (on the driver or passenger d[...]

The autolock feature repeats when: • any door is opened then closed while the ignition is in the on position and the vehicle speed is 9 mph (15 km/h) or lower , and • the vehicle attains a speed greater than 12 mph (20 km/h). Deactivating/activating autolock Y our vehicle comes with the autolock feature enabled. There are four methods to enable[...]

Keyless entry keypad procedure 1. T urn the ignition to the off position. 2. Close all doors, the liftgate and liftgate window . 3. Enter 5–digit entry code 4. Press and hold the 3 • 4. While holding the 3 • 4p r e s st h e7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has [...]

Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the off position and all vehicle doors are closed. Y ou must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again. 1. Place the [...]

CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door . Setting the lock for one door will not automatically set the lock for b[...]

The IKT allows you to: • remotely unlock the vehicle doors. • remotely lock all the vehicle doors. • remotely open the power liftgate or manual liftgate window (if equipped). • activate the personal alarm. • arm and disarm the perimeter anti-theft system. • operate the illuminated entry feature. The remote entry lock/unlock feature oper[...]

Locking the doors 1. Press and release to lock all the doors. The parking lamps will illuminate. 2. Press and release again within three seconds to confirm that all the doors are closed. Note: The doors will lock again, the horn will chirp and the turn lamps will illuminate once if all the doors and liftgate are closed. Note: If any door or the lif[...]

Sounding a panic alarm Press to activate the alarm. The horn will sound and the turn lamps will flash for a maximum of three minutes. Press again or turn the ignition to the on position to deactivate, or wait for the alarm to time out in three minutes. Note: The panic alarm will only operate when the ignition is in the off position. Memory seats/po[...]

3. A tone will be heard when the deactivation is complete. 4. Repeat this procedure for another remote entry transmitter if desired. Replacing the battery The Integrated Keyhead T ransmitter uses one coin type three-volt lithium battery CR2032 or equivalent. T o replace the battery: 1. T wist a thin coin in the slot of the IKT near the key ring in [...]

Illuminated entry The interior lamps, parking lamps and puddle lamps (if equipped) illuminate when the Integrated Keyhead T ransmitter or the keyless entry system keypad is used to unlock the door(s). The illuminated entry system will turn off the lights if: • the ignition is turned to the on position, or • the Integrated Keyhead T ransmitter l[...]

• activate or deactivate the Autolock feature if equipped • release the liftgate glass, The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’ s wallet card in the glove box and is available from your authorized dealer . Y ou can also create your own 5–digit personal entry code. When pressin[...]

The anti-scan feature will turn off after: • one minute of keypad inactivity , • pressing the control on the remote entry transmitter , • or the ignition position changes. Unlocking and locking the doors and liftgate using keyless entry T o unlock the driver’ s door , enter the factory set 5-digit code or your personal code. Each number mus[...]

engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded IKT and restart the engine. Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle. Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster .[...]

Key information Y our vehicle is supplied with two coded keys. Only a coded key will start your vehicle. Spare coded keys can be purchased from your authorized dealer . Y our authorized dealer can program your key or you can “do it yourself.” Refer to the Programming spare keys section in this chapter . The following items may prevent the vehic[...]

T ips: • Only use Integrated Keyhead T ransmitters (IKT s) or standard SecuriLock 威 keys. • Y ou must have two previously programmed coded keys (keys that already operate your vehicle’ s engine) and the new unprogrammed key(s) readily accessible. • If two previously programmed coded keys are not available, you must take your vehicle to yo[...]

If the key has been successfully programmed it will start the vehicle’ s engine and will operate the remote entry system (if the new key is an Integrated Keyhead T ransmitter). The theft indicator light will illuminate for three seconds and then go out to indicate successful programming. If the key was not successfully programmed, it will not sta[...]

• Visual warnings are displayed followed by a chime when a preselected vehicle speed of 45, 55 or 65 mph (75, 90, or 105 km/h) is exceeded • The maximum volume of the audio system is limited to 45%. MYKEY VOLUME LIMITED will be displayed in the radio or (if equipped) navigation screen when attempting to exceed the limited volume • The Advance[...]

3. If you don’t want to change the maximum speed setting, press the SETUP button to display the next menu. The remaining menus appear as follows with the default settings shown: MYKEY MPH TONES 45 55 65 <OFF> MYKEY VOLUME LIMIT <ON> OFF MYKEY ADVTRAC CTRL ON <OFF>. 4. On any of the menus press RESET to highlight your choice with[...]

T roubleshooting Condition Potential Causes Can’t create a MyKey™ • Key in the ignition is already a MyKey™ • Key in the ignition is the last remaining Admin key (there always has to be at least one Admin key) • Securilock 威 Passive Anti-Theft System is disabled or in unlimited mode Cannot program the MyKey™ optional settings • Ke[...]

Arming the system When armed, this system will respond if unauthorized entry is attempted. When unauthorized entry occurs, the system will flash the turn signal lamps and will sound the horn. The system is ready to arm whenever the key is in the off position, or is removed from the ignition. Either of the following actions will prearm the alarm sys[...]

Disarming the system Y ou can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter portion of your Integrated Keyhead T ransmitter . • Unlock the doors by using your keyless entry pad. • T urn ignition to the on position with a valid programmed SecuriLock™ key or Integrated Keyhead T ra[...]

SEA TING Adjustable head restraints Y our vehicle is equipped with front row outboard head restraints that are vertically adjustable. W ARNING: T o minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The [...]

3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint. Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants of extremely tall stature, adjust th[...]

2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint. T o reinstall the adjustable head restraint, do the following: 1. Insert the two stems into the guide sleeve collars. 2. Push the head restraint down until it locks. Properly adjust the head restraint so that the top of [...]

Lift handle to move seat forward or backward. Manual seat recliner (if equipped) W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision.[...]

Using the armrest (if equipped) Push the release control to move the armrest up or down. Using the manual lumbar support (if equipped) The lumbar support control is located on the outboard side of the seat. T urn the lumbar support control clockwise for more support. T urn the lumbar support counter -clockwise for less support. Seating and Safety R[...]

Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the control for additional support. Press the rear side of the control to reduce support. Adjusting the front power seat W ARNING: Never adjust the driver’ s seat or seatback when the vehicle is moving. W AR[...]

Move the switch in the direction of the arrows to raise or lower the rear portion of the seat cushion. Press the switch in the direction of the arrows to move the seat forward, backward, up or down. Press the control to recline the seatback forward or rearward. Note: On vehicles with memory seats, to prevent damage to the seat, the power seats are [...]

Memory seat/power mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors and adjustable pedals to two programmable positions. The memory seat control is located on the outboard side of the seat cushion. • T o program position one, move the driver seat, exterior mirrors and adj[...]

Heated seats W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater . The seat heater may cause burns even at low temperatures, especially if used for long perio[...]

Climate controlled seats air filter replacement (if equipped) The climate controlled seat system includes air filters that must be replaced periodically . Refer to the scheduled maintenance information for more information. • There is a filter located under each front seat. • The filter can be accessed from the second row seat. Move the front s[...]

T o install a filter: • First, position the filter in its housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position. REAR SEATS Folding down the 2nd row 40% seat system W ARNING: Use caution when folding th[...]

2. Locate handle on the side of the seat cushion by the door . 3. Pull up on the handle and push the seatback forward toward the front of the vehicle. T o return the seat to the upright position: 1. Lift the seatback toward the rear of the vehicle. 2. Rotate the seatback until you hear a click, locking it in the upright position. 3. Lift up on the [...]

Placing the 2nd row outboard 40% seats in cargo mode W ARNING: Use caution when folding the seatback to the flat back position as the system will move forward when you lift the release handle. The 2nd row seats can be placed in a kneel down load floor position to allow more cargo space. W ARNING: Always return the seat from the kneel position prior[...]

Returning to the upright position from full lowered load floor position The seatback cannot be returned to the upright position until the seat is returned from the kneel down position. T o return the seat to the upright position: 1. Push the seat rearward until the latch is engaged. 2. Return the seatback to the upright position. Adjusting the 2nd [...]

T o return the seat to a seating position: 1. Push the seat down and latch to the floor with a moderate amount of effort and speed. 2. Make sure the seat is latched to the floor . 3. Bring the seat back to an upright position. The seatback should lock into position. Note : If the seat back will not return to the upright position, tumble the seat ag[...]

Exiting the 3rd row 1. Pull the strap located at the bottom outboard of the seat back to release the seat from the floor , and rotate the seat up towards the front seat. 2. Follow the directions above to return the seat from the E-Z entry and to the upright position. Reclining the 2nd row outboard 40% seatback Locate the release handle on the outbo[...]

W ARNING: T o prevent possible damage to the seat or safety belts, ensure that the safety belts are not buckled when moving the seat to the load floor position. 2. W ith the latch released the seatback can be lowered into the load floor position. 3. T o return the seat to the upright position, lift the seatback until the latch is fully engaged. W A[...]

Adjusting the 2nd row center 20% seat (if equipped) Lift the handle to move the seat forward or backward. Note: This seat can be moved forward to keep a child in a child restraint close to the front seat occupants. The seat should be moved to the full rearward position when it is occupied by older children or adults, including children in booster s[...]

T o operate the heated seats: • Push the indicated side of the control for maximum heat. • Push again to deactivate. • Push the indicated side of the control for minimum heat. • Push again to deactivate. The heated seat module resets at every ignition run cycle. While the ignition is in the on position, activating the high or low heated sea[...]

Folding down the 3rd row seats to the load floor W ARNING: T o prevent possible damage to the seat or safety belts, ensure that the safety belts are not buckled when moving the seat to the load floor position. Before folding the third row seats, fold the head restraints down by pulling on the strap located at the bottom of the restraint. Pull up on[...]

Third row power folding seat (if equipped) Note : Be sure that the head restraints are folded down before powering the 3rd row seat down. The control buttons are located on the right-hand rear quarter trim panel (accessible from the liftgate area). Push the bottom portion of the control button to lower the desired seatback. Push the top of the cont[...]

The power fold down seats will operate for 10 minutes after the ignition switch is in off. The transmission must be in P (Park), and the liftgate, or liftgate glass must be open. Similar to the battery saver feature, the power 3rd row seat will be disabled 10 minutes after turning the vehicle off. If the power 3rd row seat is disabled after 10 minu[...]

the system. Rather , it means the Personal Safety System 威 determined the accident conditions (crash severity , belt usage, etc.) were not appropriate to activate these safety devices. Front airbags are designed to activate only in frontal and near -frontal collisions, not rollovers, side-impacts, or rear -impacts unless the collision causes suff[...]

Front safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’ s forward momentum. This helps reduce the risk of force-related injuries to the occupant’ s chest by limiting the load on the o[...]

W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. W ARNING: All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an airbag supplemental restraint system (SRS) is provided. W ARNING: I[...]

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. • Front and rear seats 2. T o unfasten, push the release button and remove the tongue from the buckle.[...]

Webbing extraction sensitive mode The webbing sensitive locking mode locks the webbing and prevents more belt from being pulled out if the belt is pulled out too quickly . The belt will unlock when you stop pulling on it. Automatic locking mode In this mode, the shoulder belt is pre-locked. The belt will still retract to remove any slack in the sho[...]

How to disengage the automatic locking mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and return to the vehicle sensitive (emergency) locking mode. W ARNING: After any vehicle collision, the combination lap and shoulder belt system at all passenger seating positions mus[...]

Safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and right front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, squeeze the side release buttons with your thumb and finger and slide the height adjuster down. T [...]

T o adjust the comfort guide: 1. Slip the shoulder belt into the belt guide. (The portion of the belt between the latch tongue and the D-ring, not the portion where the belt exits from the quarter trim panel.) 2. Slide the guide up or down along the webbing so that the belt is centered on the occupant’ s shoulder . W ARNING: Position the safety b[...]

Conditions of operation If... Then... The driver safety belt is not buckled before the ignition switch is turned to the on position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The saf[...]

If... Then... The driver’ s safety belt is not buckled approximately five seconds after the safety belt warning light has turned off... The Belt-Minder 威 feature is activated - the safety belt warning light illuminates and the warning chime sounds for six seconds every 30 seconds, repeating for approximately five minutes or until safety belt is[...]

Reasons given... Consider ... “I was in a hurry” Prime time for an accident. Belt-Minder 威 reminds us to take a few seconds to buckle up. “Safety belts don’t work” Safety belts, when used properly , reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. “T raffic is light” Nearly 1 of 2 deaths occur[...]

W ARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. T o do so may adversely affect the performance of the vehicle’ s air bag system Deactivating/activating the Belt-Minder 姞 feature (if equipped) Read Step s1-4t horoughly before proceeding with the deactivation/activati[...]

4. W ithin approximately seven seconds of the light turning off, buckle then unbuckle the safety belt. • This will disable the Belt-Minder 威 feature for that seating position if it is currently enabled. As confirmation, the safety belt warning light will flash four times per second for three seconds. • This will enable the Belt-Minder 威 fea[...]

W ARNING: All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. W ARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position. W ARNING: The National Highway T raffic Safety Adm[...]

W ARNING: Additional equipment may affect the performance of the airbag sensors increasing the risk of injury . Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instr[...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amo[...]

• one or more impact and safing sensors and diagnostic monitor (RCM), • a readiness light and tone • the electrical wiring which connects the components. The RCM (restraints control module) monitors its own internal circuits and the supplemental airbag electrical system wiring (including the impact sensors, the system wiring, the airbag syste[...]

W ARNING: Do not attempt to service, repair , or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. Contact your authorized dealer as soon as possible. W ARNING: All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided. How does the side airbag system work? The design and[...]

The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activation. Side airbags are designed to inflate in side-impact collisions, not roll-over , rear -impact, frontal or near -frontal collisions, unless the collision caus[...]

W ARNING: Do not attempt to service, repair , or modify the Safety Canopy 威 system, its fuses, the A, B, C or D pillar trim, or the headliner on a vehicle containing a Safety Canopy 威 . See your authorized dealer . W ARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safet[...]

• T wo crash sensors mounted in the front doors (one on each side of the vehicle). • T wo crash sensors located at the C pillar behind the rear doors (one on each side of the vehicle). • Rollover sensor in the restraints control module (RCM). The Safety Canopy 威 system, in combination with safety belts, can help reduce the risk of severe in[...]

W ARNING: If the Safety Canopy 威 system has deployed, the Safety Canopy 威 will not function again unless replaced. The Safety Canopy 威 system (including the A, B, C, and D pillar trim and headliner) must be inspected and serviced by an authorized dealer . If the Safety Canopy 威 is not replaced, it will not function again, which will increas[...]

The SOS Post-Crash Alert can be turned off when any one of the following actions are taken by the driver or any other person: • pressing the hazard control button, • or pressing the panic button on the remote entry transmitter . The feature will continue to operate until the vehicle runs out of power . Disposal of airbags and airbag equipped ve[...]

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger) Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat). Small children Children who have outgrown or no[...]

Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA TCH (lower anchors only) Safety belt and top tether anchor Safety belt and LA TCH (lower anchors and top tether anchor) Safety belt only Rear facing [...]

W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury or death. W ARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collisio[...]

restrained properly , then restrain the child in the child safety seat or with the belt-positioning booster . Remember that child seats and belt-positioning boosters vary and may be designed to fit children of different heights, ages and weights. Children who are too large for child safety seats or belt-positioning boosters (as specified by your ch[...]

When installing a child safety seat with combination lap/shoulder belts: • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. • Keep the buckle release button pointing up and away from th[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. 6. Allow the belt to retract to remove slack. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. T ry to pull the belt out of the retractor to make sure the retract[...]

10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than 1 inch (2.5 cm) of movement for proper installation. 11. Ford recommends checking wit[...]

Y our vehicle has LA TCH lower anchors for child seat installation at the seating positions marked with the child seat symbol. The LA TCH anchors are located at the rear section of the rear seat between the cushion and seatback, below the locator symbols on the seat back. Follow the child seat manufacturer’ s instructions to properly install a ch[...]

W ARNING: Never attach two child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death. If you install a child seat with rigid LA TCH attachments, and have attached the top tether strap to the proper top tether anchor , do not tighte[...]

The tether strap anchors in your vehicle are in the following positions (shown from top view): • Second row bench seat • Second row bucket seats Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor . Once the child safety seat ha[...]

• Second row outboard seating positions • Second row center seating position (if equipped) 3. Grasp the tether strap and position it to the seat frame. 4. Rotate the tether strap, and clip the tether strap to the anchor on the seat frame. Seating and Safety Restraints 239 2010 Expedition (exd) Owners Guide (own2002) , 1st Printing USA (fus)[...]

5. Rotate the tether strap clip. 6. T ighten the child safety seat tether strap according to the manufacturer’ s instructions. Third row center seating position 1. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head r[...]

3. Clip the tether strap through the anchor loop as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 4. T ighten the child safety seat tether strap according to the manufacturer’ s instructions. If the safety seat is not anchored properly , the risk of a child bein[...]

Booster seats position a child so that vehicle lap/shoulder safety belts fit better . They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably at the edge of the cushion, while minimizing slouching. Booster seats may also make the shoulder belt fit better and more comfortably . T ry to keep the belt near [...]

T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head [...]

Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to [...]

Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision. Child restraint and safety belt maintena[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter . Information on transfer case maintenance can be found in the Maintenance and Specifications ch[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versa[...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon t[...]

TIRES T ires are designed to give many thousands of miles of service, but they must be maintained in order to get the maximum benefit from them. Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry . • T ire Identification [...]

INFLATING Y OUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least o[...]

The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or T ire Label. When weather temperature changes occur , tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressur[...]

TIRE CARE Inspecting your tires and wheel valve stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check the tire and valve stems for holes, cracks, or cuts that may permit air leakage and repair or replace the tire and replace the valve [...]

W ARNING: Age T ires degrade over time depending on many factors such as weather , storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear . However , heat caused by hot climates or frequent high loadi[...]

W ARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford. The recommended tire and wheel size may be found on either the Safety Compliance Certification Label or the T ire Label which is locate[...]

It is recommended that the two front tires or two rear tires generally be replaced as a pair . The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your T ire Pressure Moni[...]

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically . Wheel misalignment in t[...]

Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y our vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, s[...]

4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire’ s load index. It is an index that relates to how much weight a tire can carry . Y ou may find this information in your Owner[...]

8. U.S. DOT T ire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For exa[...]

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’ s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or T ir[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. T ire Quality Grades do not apply to this type of tire. 1. T: Ind[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard[...]

The T ire Pressure Monitoring System complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The[...]

Understanding your Tire Pressure Monitoring System (TPMS) The T ire Pressure Monitoring System measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The Low T ire Pressure W arning Lamp will turn ON if the tire pressure is significantly low . Once the light is illuminated, your tires are under inflated and [...]

When you believe your system is not operating properly The main function of the T ire Pressure Monitoring System is to warn you when your tires need air . It can also warn you in the event the system is no longer capable of functioning as intended. Please refer to the following chart for information concerning your T ire Pressure Monitoring System:[...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a description of how the system functions under these conditions, refer to When your temporary sp[...]

SNOW TIRES AND CHAINS W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover , personal injury and death. Add[...]

capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle’ s weight ratings, with or without a trailer , from the vehicle’ s T ire Label or Safety Compliance Certificatio[...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. Tires,[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Note: For trailer towing information r[...]

• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury . Tires, Wheels and Loading 272 2010 Expedition (exd) Owners Guide[...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

W ARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.” on your vehicle’ s placard. 2. Determine the combined weight of[...]

to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 - 540 = -103 [...]

• Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter . • Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter . • Service your vehicle more frequently if you tow a trailer . Refer to the severe duty schedule in the scheduled maintenance guide. • Do not tow a t[...]

Engine Rear axle ratio Maximum GCWR - lb. (kg) T railer weight range (0 - maximum) lb. (kg) 4x2 5.4L with standard trailer tow package All 11800 (5352) 0–6000 (0–2721) 5.4L with optional trailer tow package All 15000 (6804) 0–9200 (0–4172) 4x4 5.4L with standard trailer tow package All 12000 (5443 ) 0–6000 (0–2721) 5.4L with optional tr[...]

Engine Rear axle ratio Maximum GCWR - lb. (kg) T railer weight range (0 - maximum) lb. (kg) Expedition EL (U.S. Only) Expedition Max (Canada Only) 4x2 5.4L with standard trailer tow package All 12100 (5488) 0–6000 (0–2721) 5.4L with optional trailer tow package All 15000 (6804) 0–8900 (0–4037) Expedition EL (U.S. Only) Expedition Max (Canad[...]

Integrated hitch rating The standard integrated hitch has two ratings depending on mode of operation: • W eight carrying - requires a draw bar and hitch ball. The draw bar supports all the vertical tongue load of the trailer . • W eight distributing - requires an aftermarket weight distributing system which includes draw bar , hitch ball, sprin[...]

Weight distributing hitch When hooking up a trailer using a load equalizing hitch, always use the following procedure: 1. Park the unloaded vehicle on a level surface. W ith the ignition in the ON position and all doors closed, allow the vehicle to stand (without passengers) for several minutes so that it can level. 2. T urn the air suspension (if [...]

The braking system of the tow vehicle is rated for operation at the GVWR not GCWR. T railer lamps T railer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. Contact your authorized dealer or trailer rental agency for proper instructions and equipment for hooking up tra[...]

• Allow more distance for stopping with a trailer attached. • If you are driving down a long or steep hill, shift to a lower gear . Do not apply the brakes continuously , as they may overheat and become less effective. • The trailer tongue weight should be 10–15% of the loaded trailer weight. • If you will be towing a trailer frequently i[...]

RECREATIONAL TOWING Follow these guidelines if you have a need for recreational towing. An example of recreational towing would be towing your vehicle behind a motorhome. These guidelines are designed to ensure that your transmission is not damaged. Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from enterin[...]

STARTING Positions of the ignition 1. Off— locks the steering wheel, automatic transmission gearshift lever and allows key removal. 2. Accessory— allows the electrical accessories such as the radio to operate while the engine is not running. 3. On— all electrical circuits operational. W arning lights illuminated. Key position when driving. 4.[...]

W ARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If[...]

4. Make sure the parking brake is set. 5. T urn the key to 3 (on) without turning the key to 4 (start). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. T urn the key to 3 (on) without turning the key to 4 (start). [...]

3. After idling for a few seconds, release the parking brake, apply the brake, shift into gear and drive. Note: If the engine does not start on the first try , turn the key to the off position, wait 10 seconds and try Step 2 again. If the engine still fails to start, press the accelerator to the floor and try Step 2 again, keeping the accelerator o[...]

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects. W ARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important ventilating information If the engine is idling while the vehic[...]

W ARNING: T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Prior to using the engine block heater , follow these recommendations for proper and safe operation: • For your safety , use an outdoor extension cord that is product certified by Underwriter’ s Laborat[...]

How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. T o clean them, use a dry cloth. Depending on the type of factory installed equipment, your engine block heater system may consume anywhere between 400 watts or 1000 watts of power per hour . Y our factory installed block heater system does not have a[...]

Anti-lock brake system (ABS) On ABS-equipped vehicles, a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events. Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel, bumps, wet or snowy roads is normal and indicates proper functioning of the vehicle’ s anti-l[...]

Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned on) until the parking brake is released. W ARNING: If the parking brake is fully [...]

Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . ADVANCET RAC 姞 WITH ROLL STABILITY CONTROL™ (RSC 姞 ) STABILITY ENHANCEMENT SYSTEM (IF EQUIPPED) W ARNING: V ehicle modifications involving braking system, aftermarket roof racks, suspension, steeri[...]

W ARNING: If a failure has been detected within the AdvanceT rac 威 with RSC 威 system, the ⬙ sliding car ⬙ icon will illuminate steadily . V erify that the AdvanceT rac 威 with RSC 威 system is not manually disabled (push the AdvanceT rac 威 with RSC 威 “Off “ button located on the center of the instrument panel). If the ⬙ sliding [...]

Note: If the system cannot be turned off, refer to MyKey™ in the Locks and Security chapter for more information. When AdvanceT rac 威 with RSC 威 performs a normal system self-check, some drivers may notice a slight movement of the brake, and/or a rumble, grunting, or grinding noise after startup and when driving off. When an event occurs that[...]

Electronic Stability Control (ESC) Electronic Stability Control (ESC) may enhance your vehicle’ s directional stability during adverse maneuvers, for example when cornering severely or avoiding objects in the roadway . ESC operates by applying brakes to one or more of the wheels individually and, if necessary , reducing engine power if the system[...]

Switching Off T raction Control If the vehicle is stuck in snow , mud or sand, and seems to lose engine power , switching off the T raction Control features of the AdvanceT rac 威 with RSC 威 system may be beneficial because the wheels are allowed to spin. This will restore full engine power and will enhance momentum through the obstacle. T o swi[...]

During trailer sway control events the “sliding car” icon in the instrument cluster will flash momentarily . The cluster message center will also display TRAILER SW A Y REDUCE SPEED . In some cases when trailer sway is detected, the vehicle speed is too high and may be above a speed at which trailer sway will not grow continuously . This may ca[...]

If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually , but it takes more effort. If the steering wanders or pulls, check for: • Underinflated tire(s) on any wheel(s) • Uneven vehicle loading • High crown in center of road • High crosswinds • Wheels out of alignment • Loose or worn[...]

If the system is off, the rear air suspension will not operate and will not raise (pump) or lower (vent) while the vehicle is not moving. However , if the system determines that the vehicle is low or high and needs to make a height adjustment while driving at speeds above 15 mph (24 km/h), the system will pump or vent as required. Normal vehicle op[...]

W ARNING: Loaded vehicles, with a higher center of gravity , may handle differently than unloaded vehicles. Do not overload your vehicle and use extra precautions, such as driving at slower speeds, avoiding abrupt steering changes and allowing for increased stopping distance, when driving a heavily loaded vehicle. Over -loading or loading the vehic[...]

4. Using a flat-head screwdriver or similar tool, move the brake-shift interlock actuator spindle toward the left, apply the brake and shift the transmission into N (Neutral). 5. Start the vehicle. 6. Reinstall the access plug. W ARNING: Do not drive your vehicle until you verify that the brakelamps are working. W ARNING: Always set the parking bra[...]

If the fuse is not blown and the brakelamps are working properly , the following procedure will allow you to move the gearshift lever from P (Park): 1. Apply the parking brake, turn the ignition key to the off position, and remove the key . 2. Using a screwdriver (or similar tool), carefully pry off and remove the chrome trim ring (1) from the shif[...]

W ARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer . AUTOMATIC TRANSMISSION OPERATION Driving with a 6–speed automatic transmission Y our vehicle has been designed to improve fuel economy by reducing fuel usage while coasting or dece[...]

T o put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the off position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever[...]

• Floor -shift transmission The TOW HAUL indicator light will illuminate in the instrument cluster . T ow/Haul delays upshifts to reduce frequency of transmission shifting. T ow/Haul also provides engine braking in all forward gears when the transmission is in the D (Overdrive) position; this engine braking will slow the vehicle and assist the dr[...]

2 (Second) T ransmission operates in 2nd gear only . Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • T ransmission operates in 1st gear only . • Provides maximum engine braking. • Allows upshifts by moving gearshift lever . • W ill not downshift into 1 (First) at high speeds; a[...]

W ARNING: T o help avoid personal injury , always use caution when in R (Reverse) and when using the reverse sensing system. W ARNING: This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting objects to avoid damaging the vehicle. The system may not de[...]

While receiving a warning the radio volume will be reduced to a predetermined level. After the warning goes away , the radio will return to the previous value. Audible W arnings Distance to Object W arning Speed above 2.5 mph (4 km/h) up to 1.6 feet (.5 meters) Solid 1.6 feet (.5 meters) to 3.1 feet (1 meter) Fast beep 3.1 feet (1 meter) to 5.7 fee[...]

The message center will indicate the system is off and will not allow the driver to switch the system on to indicate a failure of the reverse sensing system. The radar sensor is located behind the rear bumper/fascia. Always keep the rear bumper/fascia free from snow , ice and large accumulations of dirt. These elements may cause the system to opera[...]

Image delay if displayed through the rearview mirror: When shifting out of R (Reverse) and into any other gear , the image in the rearview mirror will remain on for a few seconds before it shuts off to assist in parking or trailer hookup. Image delay if displayed through the Navigation screen: After shifting out of R (Reverse) and into any gear oth[...]

If the back end of the vehicle is hit or damaged, then check with your authorized dealer to have your rear video system checked for proper coverage and operation. Night time and dark area use At night time or in dark areas, the reverse camera system relies on the reverse lamp lighting to produce an image. Therefore it is necessary that both reverse[...]

4WD indicator lights The indicator lights illuminate in the message center in the reconfigurable telltale (RTT) location under the following conditions. Refer to W arning lights and chimes in the Instrument Cluster chapter . • 4X2 - Momentarily illuminates when 2H is selected. • 4X4 AUTO – Illuminates when 4X4 AUTO is selected. • 4X4 – Il[...]

dry pavement. This position is only intended for severe winter or off-road conditions, such as deep snow , ice or shallow sand. • 4L (4X4 LOW) provides electronically locked four -wheel drive when extra power at reduced speeds is required. The message center will display “4X4 LOW” when this position is selected. This position is not recommend[...]

Shifting between 4A and 4H Move the control between 4A to 4H at a stop or while driving at any speed. The message center will display “4X4” if 4H is selected and ⬙ 4X4 Auto if 4A is selected. Shifting to/from 4L 1. Bring the vehicle to a speed of 3 MPH (5 KPH) or less. 2. Place the gearshift in N (Neutral). 3. Move the control to the desired [...]

Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. Y ou should either know the t[...]

If your vehicle gets stuck If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear . Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur . [...]

W ARNING: V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily unde[...]

A void excessive speed because vehicle momentum can work against you and cause the vehicle to become stuck to the point that assistance may be required from another vehicle. Remember , you may be able to back out the way you came if you proceed with caution. If your vehicle is equipped with AdvanceT rac 威 with RSC, press the AdvanceT rac 威 with[...]

“T read Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas. Ford Motor Company joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treadin[...]

Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear . When descending a steep hill, avoid sudden hard braking as you could lose control. When you brake hard, the front wheels can’t tu[...]

W ARNING: If you are driving in slippery conditions that require tire chains or cables, then it is critical that you drive cautiously . Keep speeds down, allow for longer stopping distances and avoid aggressive steering to reduce the chances of a loss of vehicle control which can lead to serious injury or death. If the rear end of the vehicle slide[...]

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water , traction or brake capability may be limited. Also, wate[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the coverage period listed on the Roadsi[...]

Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic W arr[...]

Note: W ith extended use, the flasher may run down your battery . FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been ac[...]

FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage r[...]

Passenger compartment fuse panel The fuse panel is located under the right-hand side of the instrument panel. T o remove the trim panel for access to the fuse box, pull the panel toward you and swing it out away from the side and remove it. T o reinstall it, line up the tabs with the grooves on the panel, then push it shut. T o remove the fuse box [...]

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Smart window #1 2 15A Driver side memory module 3 15A Family entertainment system, Audio rear seat controls, Satellite radio, SYNC 威 4 30A Smart window #2 5 10A Keypad illumination, 3rd row seat enable, Brake shift interlock (BSI), Passenger compartment f[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 23 15A High beam headlamps 24 20A Horn 25 10A Demand lamps, Glovebox, V isor 26 10A Instrument panel cluster 27 20A Ignition switch 28 5A Radio 29 5A Instrument panel cluster 30 5A Not used (spare) 31 10A Not used (spare) 32 10A Airbag module 33 10A Not used (spare) 34 5A Not used (spare) 35 10[...]

Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. W ARNING: Always disconnect the battery before servicing high current fuses. W ARNING: T o reduce risk of electrical shock, always repla[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 4 — T railer tow battery charge relay 5 — Fuel pump relay 6 — Electronic fan 1 relay 7 — Rear window defroster/heated mirror relay 8 — Electronic fan 3 relay 9 — Run/Start (R/S) relay 10 — Rear air suspension (RAS) relay 11 40A** Power running board 12 40A** R/S relay 13 30A ** St[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 32 40A** Blower motor relay 33 — Not used 34 30A** Auxiliary blower motor 35 30A** PCM relay 36 30A** Power liftgate 37 — T railer tow left hand stop/turn relay 38 — T railer tow right hand stop/turn relay 39 — Backup lamps relay 40 — Blower motor relay 41 10A* PCM keep-alive power 42[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 59 15A* Heated mirrors 60 — One-touch start diode 61 — Fuel pump diode 62 — Not used 63 25A** Electronic fan 64 30A** Moon roof 65 20A** Auxiliary power point 2 66 20A** Auxiliary power point 3 67 40A** Climate controlled seats 68 60A** ABS valves 69 60A** ABS pump 70 40A** Third row powe[...]

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use. T o restore the full[...]

2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONL Y” When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label[...]

• W et weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • T owing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack[...]

Removing the jack and tools 1. Open the liftgate, then locate the access panel on the floor behind the 3rd row seat. Unlatch and remove the panel. 2. Remove the jack and tools assembly tray from the compartment by turning the wing-nut counterclockwise to relieve tension against the jack assembly tray . Remove the bag from the jack and tool assembly[...]

Tire change procedure W ARNING: T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block the wheels (both front or both rear) on the opposite end of the vehicle from the wheel being changed. If on a grade, block both opposite wheels on the downward side of the hill. W ARNING: If the vehicle slips[...]

1. Block the wheels (both front or both rear) on the opposite end of the vehicle from the wheel being changed. If on a grade, block both wheels on the downward side of the hill. 2. T urn off the air suspension system (if equipped - the air suspension system is controlled through the message center . Refer to Air suspension system in the Driving cha[...]

W ARNING: When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park). T o prevent the vehicle from moving when you change the tire, be sure that the parking brake is set and block the wheels (both front or both rear) on the opposite[...]

• Never use the front or rear differential as a jacking point. W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 7. Remove the lug nuts with the lug wrench. 8. Replace t[...]

2. Slide the wheel partially under the vehicle and install the retainer through the wheel center . If equipped, you may have to remove the wheel center cap prior to pushing the retainer through the center of the wheel. T o remove the center cap, press it off with the jack tool from the inner side of the wheel. After doing so, pull on the cable to a[...]

W ARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Ensure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the[...]

JUMP STARTING W ARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. W ARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your automatic transmission vehicle. Automatic transmiss[...]

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the [...]

4. Make the final connection of the negative (-) cable to the jump starting stud located in the engine compartment, near the washer fluid bottle. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points. W ARNING: Do not connect the end of the second cable to th[...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the rev[...]

2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper ca[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a sl[...]

If the vehicle is towed by other means or incorrectly , vehicle damage may occur . Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle. Emergency towing In case of a roadside emergency with a disabled vehicle ([...]

GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certai[...]

In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-[...]

In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights[...]

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . If a warranty concern has not been resolved using the three-step procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program. The BBB A[...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]

If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: FORD MOTOR COMP ANY FORD EXPORT OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. T elephone: ([...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Neve[...]

• After polishing chrome bumpers, apply a coating of Motorcraft Premium Liquid W ax (ZC-53-A), available from your authorized dealer , or an equivalent quality product to help protect from environmental effects. W AXING • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid W ax (ZC-53-A), which is[...]

ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine bl[...]

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle’ s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellent coatings, tree sap, or other organic con[...]

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with a clean, damp, white cotton cloth, then use a clean and dry white cotton cloth to dry these areas. • A void cleaners or polishes that increase the gloss of the upper portion of the instrument panel. The dull finish in this area he[...]

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side airbags: • Remove dust and loose dirt with a vacuum cleaner . • Remove light stains and soil with Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material, spot-clean the area first with Motorcraf[...]

• If the leather cannot be completely cleaned using a mild soap and water solution, the leather may be cleaned using a commercially available cleaning product designed for automotive interiors. • Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber , vinyl and plastics, or oil/petroleum-based leath[...]

Scratches Natural Markings - Because the leather in the seat comes from genuine steer hides, there will be evidence of naturally occurring markings, such as small scars. These markings give character to the seating covers and should be considered as proof of a genuine leather product. In order to lessen the appearance of certain scratches and other[...]

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Eac[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide/Customer Information Guide to find out which parts and servi[...]

Working with the engine on 1. Set the parking brake and shift to P (Park). 2. Block the wheels. W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle lo[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L V8 1. W indshield washer fluid reservoir 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Power distribution box 8. Engine oil filler cap 9. Battery Maintenance and Specifications 370 2010 Expedition (exd) Own[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streak[...]

CHANGING THE WIPER BLADES It is recommended that wiper blades are renewed before winter . T o replace the wiper blades: 1. Fold back the wiper arm and position the wiper blade at right angles to the wiper arm. 2. T o remove, press the retaining clip (A) to disengage the wiper blade, then pull the blade down toward the windshield to remove it from t[...]

4. T o attach the new wiper to the wiper arm, align the cross pin and keyway (denoted with the arrows) and firmly press the wiper blade into the wiper arm until an audible snap is heard. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehic[...]

• If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter . • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be[...]

Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the Internatio[...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Als[...]

W ARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. A void contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medi[...]

• If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of au[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the FULL COLD level or within the COLD FILL RANGE as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read and underst[...]

• Do not mix coolants. Add the coolant type originally equipped in your vehicle. Refer to Maintenance product specifications and capacities in this chapter . Note: Do not use stop leak pellets or cooling system sealants/additives as they can cause damage to the engine cooling and/or heating systems. This damage would not be covered under your veh[...]

4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, to within the COLD FILL RANGE or the FULL COLD level on the reservoir . If you removed the radiator cap in an overflow system, fill the radiator until the c[...]

• NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protec[...]

When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase. Once the engine temperature cools, the engine can be re-s[...]

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions W ARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. W ARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel™ “no cap” fuel system), do not[...]

• Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water . Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other f[...]

W ARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. W ARNING: The flow of fuel through a fuel pump nozzle can produce static electricity , which can[...]

When fueling your vehicle: 1. T urn the engine off. 2. Open the fuel filler door . 3. Slowly insert the fuel filler nozzle fully into the fuel system. Pump fuel as normal. 4. After you are done pumping fuel, slowly remove the fuel filler nozzle—allow about five seconds after pumping fuel before removing the fuel filler nozzle. This allows residua[...]

Flex Fuel V ehicle (FFV) fuel fill inlet Flex fuel vehicles have a yellow bezel placed over the fuel fill inlet. Choosing the right fuel Use only UNLEADED FUEL and FUEL ETHANOL (Ed75–Ed85). The use of leaded fuel is prohibited by law and could damage your vehicle. Y our vehicle was not designed to use fuel or fuel additives with metallic compound[...]

It is best not to alternate repeatedly between gasoline and E85. If you do switch fuels, it is recommended that you add as much fuel as possible—at least half a tank. Do not add less than five gallons (18.9L) when refueling. Y ou should drive the vehicle immediately after refueling for at least 5 miles (8 km) to allow the vehicle to adapt to the [...]

• Normally , adding 1 gallon (3.8L) of fuel is enough to restart the engine. If the vehicle is out of fuel and on a steep grade, more than 1 gallon (3.8L) may be required. • The service engine soon indicator may come on. For more information on the service engine soon indicator , refer to W arning lights and chimes in the Instrument Cluster cha[...]

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Y our best source of information about actual fuel economy is you, the driver . Y ou must gather information as accurately and consistently as possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy . W e do not recommend taking fuel econ[...]

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (in gallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odomet[...]

• Y ou may want to turn off the speed control in hilly terrain if unnecessary shifting between the top gears occurs. Unnecessary shifting of this type could result in reduced fuel economy . • W arming up a vehicle on cold mornings is not required and may reduce fuel economy . • Resting your foot on the brake pedal while driving may reduce fue[...]

EP A fuel economy estimates Every new vehicle should have a sticker on the window called the Monroney Label which contains EP A fuel economy estimates. Contact your authorized dealer if the Monroney Label is not supplied with your vehicle. The EP A fuel economy estimates should be your guide for the fuel economy comparisons with other vehicles. Y o[...]

W ARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine. By law , vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentional[...]

If the service engine soon indicator remains on, have your vehicle serviced at the first available opportunity . Although some malfunctions detected by the OBD-II may not have symptoms that are apparent, continued driving with the service engine soon indicator on can result in increased emissions, lower fuel economy , reduced engine and transmissio[...]

POWER STEERING FLUID Check the power steering fluid. Refer to scheduled maintenance information. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and rig[...]

T RANSMISSION FLUID Checking automatic transmission fluid The automatic transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Y our transmission does not consume fluid. However , the fluid level should be checked if the transmission is not work[...]

2. Unlock the locking clip on the connector (connector shown from below for clarity), then squeeze and pull the connector off of the air outlet tube. 3. Clean the area around the air tube to air cover connection to prevent debris from entering the system and then loosen the bolt on the air tube clamp so the clamp is no longer snug to the air tube. [...]

6. Remove the air filter element from the air filter housing. 7. Install a new air filter element. 8. Replace the air filter housing cover and secure the clamps. Be careful not to crimp the filter element edges between the air filter housing and cover and ensure that the tabs on the edge are properly aligned into the slots. 9. Slip the air tube ont[...]

Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not used. MOTORCRAFT PART NUMBERS Component 5.4L 3V V8 engine Air filter element F A-1883 Battery BXT -65-650 or BXT -65-750 (if equipped) Oil filter FL-820-S Spa[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name Ford part number / Ford specification Brake fluid Between MIN and MAX on reservoir Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid PM-1-C / WSS-M6C62-A or WSS-M6C65-A1 Hinges, latches, striker plates and rotors, seat tracks, fuel filler door hinge and spring[...]

Item Capacity Ford part name Ford part number / Ford specification Engine oil 7.0 quarts (6.6L) • Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil • Motorcraft SAE 5W -20 Full Synthetic Motor Oil (US) • Motorcraft SAE 5W -20 Super Premium Motor Oil • Motorcraft SAE 5W20 Synthetic Motor Oil (Canada) 2 • XO-5W20-QSP (US) • XO-5W20-[...]

Item Capacity Ford part name Ford part number / Ford specification T ransfer case fluid (4X4) 1.6-1.8 quarts (1.5-1.7L) Motorcraft T ransfer Case Fluid XL–12 / — W indshield washer fluid 4.5 quarts (4.1L) Motorcraft Premium W indshield W asher Concentrate ZC-32-A / WSB-M8B16-A2 Fuel tank (Standard) 28.0 gallons (106.0L) —— Fuel tank (Expedi[...]

ENGINE DATA Engine 5.4L V8 engine Cubic inches 330 Fuel 87 octane or (E-85) Firing order 1-3-7-2-6-5-4-8 Ignition system Coil on plug Spark plug gap 0.039–0.043 inch (1.05 +/– 0.05mm) Compression ratio 9.8:1 Maintenance and Specifications 405 2010 Expedition (exd) Owners Guide (own2002) , 1st Printing USA (fus)[...]

Engine drivebelt routing IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label i[...]

V ehicle identification number (VIN) The vehicle identification number is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number . The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross [...]

T RANSMISSION CODE DESIGNATIONS Y ou can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents. Description Code Six-speed automatic (6R80 ) 6 Maintenance and Specifications 408 2010 Expedition (exd) Owners Guide (own2002) , 1st Printing USA (fus)[...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your veh[...]

Lifestyle Ash cup / smoker’ s package Cargo organization and management Roof crossbars T railer towing accessories Peace of mind Remote start V ehicle security systems Locking gas plug for capless fuel system Wheel locks For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: ?[...]

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage. Up to 500+ Covered V ehicle Components There [...]

Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract. W ith Ford ESP , you minimize your risk for unexpected repair bills and rising repair costs. A void the rising cost of properly maintaining your vehicle! Ford ESP also offers a Premium Maintenance P[...]

Ford Extended Service Plan 413 2010 Expedition (exd) Owners Guide (own2002) , 1st Printing USA (fus)[...]

A ABS (see Brakes) ..................... 291 Accessory delay ........................ 133 AdvanceT rac .............................. 293 Air cleaner filter ...............398, 401 Air suspension ...........................299 description .............................. 299 Airbag supplemental restraint system ........................217, 221, 223 a[...]

LA TCH ..................................... 235 recommendations ................... 229 Child safety seats - booster seats ........................................... 242 Cleaning your vehicle engine compartment .............. 361 instrument panel ....................363 interior ..................................... 364 plastic parts ............[...]

change oil soon warning, message center ....................... 373 checking and adding .............. 373 dipstick .................................... 373 filter , specifications ........ 375, 401 recommendations ................... 375 refill capacities ........................ 402 specifications .......................... 402 Event data recordi[...]

Illuminated visor mirror ...........128 Infant seats (see Safety seats) ..................... 231 Inspection/maintenance (I/M) testing ........................................ 396 Instrument panel cleaning ................................... 363 cluster ........................................ 12 lighting up panel and interior .....................[...]

Oil (see Engine oil) .................. 373 P Parental MyKey programming ............................. 177 Parking brake ............................ 292 Parts (see Motorcraft parts) ....401 Pedals (see Power adjustable foot pedals) ............................... 136 Power adjustable foot pedals ...136 Power deployable running boards .............[...]

Satellite Radio Information ........ 67 Seats .......................................... 183 child safety seats .................... 231 cleaning ................................... 365 climate control ........................ 192 heated ...................................... 200 memory seat ................... 169, 190 SecuriCode keyless entry sys[...]

V V ehicle Identification Number (VIN) .......................................... 407 V ehicle loading .......................... 268 V entilating your vehicle ........... 288 W W arning lights (see Lights) .......12 W asher fluid .............................. 371 W ater , Driving through ............. 323 W indows power ..........................[...]