Ford F-450 (2007) Bedienungsanleitung
- Schauen Sie die Anleitung online durch oderladen Sie diese herunter
- 311 Seiten
- N/A
Zur Seite of
Ähnliche Gebrauchsanleitungen
-
Car
Ford Escape (2015)
448 Seiten -
Car
Ford Fiesta - juni 2010 - feb 2011
236 Seiten 8.35 mb -
Car
Ford Fiesta 2015
340 Seiten 4.76 mb -
Car
Ford Mondeo - april 2012 - april 2013
344 Seiten 7.57 mb -
Car
Ford Transit Connect - okt 2008 - april 2009
2 Seiten 1.31 mb -
Car
Ford Focus Electric 2014
290 Seiten 23.1 mb -
Car
Ford Focus - april 2012 - mei 2012
344 Seiten 1.04 mb -
Car
Ford Mondeo (1996)
279 Seiten
Richtige Gebrauchsanleitung
Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Ford F-450 (2007) an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Ford F-450 (2007), sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.
Was ist eine Gebrauchsanleitung?
Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Ford F-450 (2007) die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.
Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Ford F-450 (2007). Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.
Was sollte also eine ideale Gebrauchsanleitung beinhalten?
Die Gebrauchsanleitung Ford F-450 (2007) sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Ford F-450 (2007)
- Den Namen des Produzenten und das Produktionsjahr des Geräts Ford F-450 (2007)
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Ford F-450 (2007)
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen
Warum lesen wir keine Gebrauchsanleitungen?
Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Ford F-450 (2007) zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Ford F-450 (2007) und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Ford finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Ford F-450 (2007) zu überspringen, wie es bei der Papierform passiert.
Warum sollte man Gebrauchsanleitungen lesen?
In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Ford F-450 (2007), über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.
Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Ford F-450 (2007) widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.
Inhaltsverzeichnis der Gebrauchsanleitungen
-
Seite 1
Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 16 Entertainment Systems 21 AM/FM stereo 21 AM/FM stereo with CD 23 AM/FM stereo with in-dash six CD 28 Satellite radio information 34 Climate Controls 38 Heater only 38 Manual heating and air conditioning 39 Automatic temperature control 41 Lights 44 Headlamps 44 T urn signa[...]
-
Seite 2
Locks and Security 85 Keys 85 Locks 85 Seating and Safety Restraints 94 Seating 94 Safety restraints 101 Airbags 113 Child restraints 121 Tires, Wheels and Loading 133 T ire information 136 T ire inflation 137 V ehicle loading 153 T railer towing 160 T railer brake controller -integrated 164 Recreational towing 170 Driving 172 Starting 172 Brakes 1[...]
-
Seite 3
Cleaning 248 Maintenance and Specifications 256 Hood 257 Engine compartment 258 Engine oil 261 Battery 265 Engine coolant 267 Fuel information 273 Air filter(s) 291 Part numbers 293 Refill capacities 294 Accessories 301 Index 304 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any inf[...]
-
Seite 4
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]
-
Seite 5
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. W arning symbols on your vehicle When you see this symbol, i[...]
-
Seite 6
SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide. Service Data Recording Service data recorders in your vehicle are capable of collecting and s[...]
-
Seite 7
limited warranty for your vehicle chapter of your vehicle’ s W arranty Guide for more information. Some vehicles are equipped with Powertrain Control Systems that can detect and store information about vehicle modifications that increase horsepower and torque output; this information cannot be erased and will stay in the system’ s memory even i[...]
-
Seite 8
Notice to owners of diesel-powered vehicles Read the 6.0 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for information regarding correct operation and maintenance of your Diesel-powered light truck. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate [...]
-
Seite 9
If your vehicle is equipped with the Ford Ambulance Preparation Package, it will be indicated on the Safety Compliance Certification Label. The label is located on the driver’ s side door pillar or on the rear edge of the driver’ s door . Y ou can determine whether the ambulance manufacturer followed Ford’ s recommendations by directly contac[...]
-
Seite 10
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag-Front Airbag-Side Child Seat Child Seat Installation W arning Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based Powertrain Malfunction S[...]
-
Seite 11
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Corr[...]
-
Seite 12
W ARNING LIGHTS AND CHIMES Standard instrument cluster (manual transmission) Standard instrument cluster (automatic transmission) Harley-Davidson instrument cluster W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one [...]
-
Seite 13
Many lights will illuminate when you start your vehicle to make sure the bulbs work. If any light remains on after starting the vehicle, have the respective system inspected immediately . If your vehicle is equipped with a diesel engine, it has a unique cluster; refer to Starting the engine in your 6.0 Liter Power Stroke Direct Injection T urbo Die[...]
-
Seite 14
Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and ST ART , or by applying the parking brake when the ignition is turned to the ON position. If the brake system warning light[...]
-
Seite 15
Charging system: Illuminates when the battery is not charging properly . T ransmission T ow/Haul Feature (automatic transmission): Illuminates when the T ow/Haul feature has been activated. Refer to the Driving chapter for transmission function and operation. If the remains on, have the system serviced immediately , damage to the transmission could[...]
-
Seite 16
GAUGES Speedometer: Indicates the current vehicle speed. Standard instrument cluster Harley-Davidson instrument clusters Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheatin[...]
-
Seite 17
Odometer: Registers the total miles (kilometers) of the vehicle. Refer to Message Center in the Drivers Controls chapter on how to switch the display from Metric to English. • W ith Mini Message Center • W ith Full Message Center T rip odometer: Registers the miles (kilometers) of individual journeys. • W ith Mini Message Center Press and rel[...]
-
Seite 18
T achometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Standard instrument cluster Harley-Davidson instrument cluster Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal operating range (between “[...]
-
Seite 19
Battery voltage gauge (manual transmission only): Indicates the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range, have the vehicle’ s electrical system checked as soon as possible. T ransmission fluid temperature gauge (automatic transmission only): If the gauge is in the: [...]
-
Seite 20
If the gauge is operating in the Y ellow or Red area, stop the vehicle and verify the airflow is not restricted such as snow or debris blocking airflow through the grill. If the gauge continues to show high temperatures, see your authorized dealer . 2007 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Instrument Cluster 20[...]
-
Seite 21
AUDIO SYSTEMS AM/FM stereo system (if equipped) The AM/FM stereo system does not contain rear speakers; only front driver side and passenger side speakers. Accessory delay: Y our vehicle is equipped with accessory delay . With this feature, the window switches and radio may be used for up to ten minutes after the ignition is turned off or until eit[...]
-
Seite 22
BASS (Bass): Press AUDIO to reach the bass setting. Use / / SEEK . BAL (Balance): Press AUDIO to reach the balance setting. Use / / SEEK to adjust between the left and right speakers. 3. SEEK: Press SEEK to access the previous/next strong station. 4. Memory presets: T o set a station: Select frequency band AM/FM1/FM2; tune to a station, press and h[...]
-
Seite 23
AM/FM stereo/single CD with satellite compatible sound system (if equipped) 1. / (T uner): Press to manually go up or down the radio frequency . Press and hold for a fast advance through radio frequencies. Also use in MENU mode to select various settings: In satellite radio mode (if equipped), press / to enter TEXT MODE and scroll through the curre[...]
-
Seite 24
2. MUTE/ : Press to mute the playing media. Press again to return to the playing media. 3. MENU: Press MENU repeatedly to gain access to the following settings: CA TEGOR Y (satellite radio, if equipped): Press MENU until the currently active category appears in the display (CA TEGORY MODE). In CA TEGORY MODE, press / to scroll through the lists of [...]
-
Seite 25
F ADE (Fade): Press MENU to reach the fade setting. Use / / SEEK, SEEK to adjust the audio between the front and rear speakers. SPEEDVOL (Speed sensitive volume) (if equipped): Press MENU to reach the SPEEDVOL setting. Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Use the / / SEEK, SEEK to adj[...]
-
Seite 26
In TEXT MODE, press SEEK, SEEK to view the previous/additional display text. In CA TEGOR Y MODE, press SEEK, SEEK to select a category . Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability 6. SHUFFLE: In CD mode, press SHUFFLE to play tracks in random order . 7. COMPRESS (Compressio[...]
-
Seite 27
13. AM/FM: Press AM/FM to select AM/FM1/FM2. 14. ON/OFF/V olume: Press VOL - PUSH to turn ON/OFF . T urn VOL - PUSH to increase/decrease volume. Note: If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition is turned back on. 15. CD: Press CD to ent[...]
-
Seite 28
Premium in-dash six CD/satellite compatible sound system (if equipped) 1. / (T uner/Disc selector): In radio mode, press to manually go up or down the radio frequency . Press and hold for a fast advance through radio frequencies. In CD mode, press / to select a desired disc (1–6). Press and hold for a fast advance through all loaded discs. Also u[...]
-
Seite 29
Satellite radio is available only in the continental United States with a valid SIRIUS radio subscription. 2. MUTE/ : Press mute button to mute playing media. Press again to return to the playing media. 3. MENU: Press the MENU button to gain access to various settings: CA TEGOR Y (satellite radio, if equipped): Press MENU until the currently active[...]
-
Seite 30
F ADE (Fade): Press MENU to reach the fade setting. Use / / SEEK, SEEK to adjust the audio between the front and rear speakers. SPEEDVOL (Speed sensitive volume) (if equipped): Press MENU to reach the SPEEDVOL setting. Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Use the / / SEEK, SEEK to adj[...]
-
Seite 31
In CA TEGOR Y MODE, press SEEK, SEEK to select a category . Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability 6. SHUFFLE: In CD mode, press SHUFFLE to play tracks in random order . 7. COMPRESS (Compression): In CD mode, press COMPRESS to bring soft and loud CD passages together fo[...]
-
Seite 32
14. ON/OFF/V olume: Press VOL - PUSH to turn ON/OFF . T urn VOL - PUSH to increase/decrease volume. Note: If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition is turned back on. 15. CD: Press CD to enter CD mode. If a CD is already loaded into th[...]
-
Seite 33
• T errain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception. • Station overload: When you pass a broadcast tower , a stronger signal may overtake a weaker one and play while the weak station frequency is displayed. CD/CD player care Do: • Handle discs by their [...]
-
Seite 34
CDs with homemade paper (adhesive) labels should not be inserted into the CD player as the label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. Audio[...]
-
Seite 35
SIRIUS satellite radio service: SIRIUS Satellite Radio is a continental U.S. based satellite radio service that broadcasts over 120 channels of music, sports, news and entertainment coast-to-coast. A service fee is required in order to receive SIRIUS service. V ehicles that are equipped with a factory installed SIRIUS Satellite Radio system include[...]
-
Seite 36
Radio Display Condition Action Required INV ALID CHNL Channel no longer available. This previously available channel is no longer available. T une to another channel. If the channel was one of your presets, you may choose another channel for that preset button. UNSUBSCRIBED Subscription not available for this channel. Contact SIRIUS at 1–888–53[...]
-
Seite 37
Radio Display Condition Action Required NO SIGNAL Loss of signal from the SIRIUS satellite or SIRIUS tower to the vehicle antenna. Y ou are in a location that is blocking the SIRIUS signal (i.e., tunnel, under an overpass, dense foliage, etc). The system is working properly . When you move into an open area, the signal should return. UPDA TING Upda[...]
-
Seite 38
HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control: : Distributes outs[...]
-
Seite 39
T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Modulate the temperature control to maintain comfort. 3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents toward the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middle of the instr[...]
-
Seite 40
: Distributes outside air through the instrument panel vents and center console vents (if equipped). : Distributes outside air through the instrument panel vents, floor vents and center console vents (if equipped). O (OFF): Outside air is shut out and the climate system is turned off. : Distributes outside air through the floor vents. : Distributes[...]
-
Seite 41
Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. AUTOMATIC T EMPERATURE CONTROL SYSTEM (IF EQUIPPED) Press the AUTO and (floor/defrost) controls at the same time and hold for one second to switch between Fahrenheit and Celsius. 1. A/C: Press to activate/deactivate air conditi[...]
-
Seite 42
4. Fan speed: Press the respective control in order to manually increase or decrease the fan speed. T o return to automatic fan operation, press AUTO. 5. (Floor/defrost): Distributes air through the instrument panel vents, floor vents and demister vents. 6. (Floor): Distributes air through the floor vents. 7. (Panel/floor): Distributes air through [...]
-
Seite 43
Operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position. • T o reduce humidity build up inside the vehicle, do not drive with the air flow selector in OFF or with recirculated air engaged. • Do not put objects under the front seats that will interfere with the airflow to th[...]
-
Seite 44
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also kee[...]
-
Seite 45
Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp control is in the , or position and the high beams are not turned on. In autolamp mode, the foglamps won’t be operational until lighting conditions warrant the activation of the headlamp/parklamp lighting. Pull headl[...]
-
Seite 46
High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move t[...]
-
Seite 47
AIMING THE HEADLAMPS Y our vehicle may be equipped with a sealed beam or aerodynamic headlamp system. Sealed beam headlamps may be aimed in the vertical (up/down) and the horizontal (left/right) directions using the procedures following. The aerodynamic headlamps can only be aimed in the vertical direction (up/down) using the following procedures. [...]
-
Seite 48
3. T urn on the low beam headlamps and open the hood. 4. Locate the high intensity area of the beam pattern and place the top edge of the intensity zone even with the horizontal reference line (4). If the top edge of the high intensity area is not even with the horizontal line, follow the next step to adjust it. 5. Locate the vertical adjuster (2) [...]
-
Seite 49
V ertical aim adjustment (aerodynamic headlamps) The headlamps on your vehicle can only be vertically adjusted. Y our vehicle does not require horizontal aim adjustments. T o adjust the headlamps: 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away . • (1) 8 feet (2.4 meters) • ([...]
-
Seite 50
T URN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. COURTESY/READING LAMPS (IF EQUIPPED) The dome lamp illuminates when any door is not completely closed, the instrument panel switch is pushed past the detent and when any of the remote entry controls are pressed while the ignition is o[...]
-
Seite 51
BULBS Headlamp condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur . This condensation is normal and will clear within 45 minutes of headlamp operation. Replacing exterior bulbs Check the operation of all the bulbs frequently . Functi[...]
-
Seite 52
Replacing headlamp bulbs (aerodynamic) 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Remove the four screws from the top and bottom front of the headlamp assembly . 3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out. If removing the lamp is difficult, removin[...]
-
Seite 53
Replacing park/turn and sidemarker lamp bulbs (aerodynamic) 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Remove the four screws from the top and bottom front of the headlamp assembly . 3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out. If removing the lamp [...]
-
Seite 54
Replacing headlamp bulbs (sealed beam) 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Remove the four screws from the top and bottom front of the headlamp assembly . 3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out. If removing the lamp is difficult, removin[...]
-
Seite 55
Replacing park/turn/sidemarker bulbs (sealed beam) 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Remove the four screws from the top and bottom front of the headlamp assembly . 3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out. If removing the lamp is diffic[...]
-
Seite 56
Replacing brake/tail/turn/back-up lamp bulbs - F–250/F–350 only 1. Make sure the headlamp switch is in the OFF position and then open the tailgate to expose the lamp assemblies. 2. Remove the two bolts from the tail lamp assembly and carefully pull the lamp assembly from the tailgate pillar by releasing the two retaining tabs. 3. Rotate the bul[...]
-
Seite 57
Replacing cargo lamp and high-mount brakelamp bulbs 1. Make sure the headlamp switch is in the OFF position. 2. Remove the two screws and lamp assembly from vehicle as wiring permits. 3. Remove the bulb socket by rotating counterclockwise. 4. Pull the bulb straight out of the socket. Front clearance and identification lamp bulbs 1. Make sure the he[...]
-
Seite 58
Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper . T o change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2. T wist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly . 3. Pull out the old bulb from the socket and push in the new [...]
-
Seite 59
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three [...]
-
Seite 60
T RANSMISSION CONTROL T ow/Haul feature (5–speed automatic transmission) (if equipped) T o activate, press the transmission control switch (TCS) located on the gearshift. The TOW/HAUL indicator light will illuminate in the instrument cluster . The transmission will operate in all gears. Press the transmission control switch again to deactivate T [...]
-
Seite 61
Storage compartment (if equipped) Press the release on the door to open the storage compartment. The storage compartment may be used to secure sunglasses or a similar object and the front tab can be used for holding tickets, paper , envelopes, etc. The front bin may be used to store small objects. AUXILIARY POWER POINT (12VDC) Power outlets are des[...]
-
Seite 62
Cigar lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage no[...]
-
Seite 63
Window lock (if equipped) The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s, press the left side of the control. Press the right side to restore the window controls. Power rear slider window (if equipped) Do not leave children unattended in the vehicle and do[...]
-
Seite 64
POWER SIDE VIEW MIRRORS (IF EQUIPPED) T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror . 2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to lock mirrors in place. Heated outside mirrors (if equippe[...]
-
Seite 65
Mirror mounted side turn signal indicator (if equipped) When the vehicle turn signals are activated, the outer portion of the mirror housing will blink amber . The turn signal feature can be seen by other drivers who may approach from the rear of the vehicle. Clearance lamps (if equipped) Illuminates when the headlamps or parking lamps are switched[...]
-
Seite 66
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you. The adjustment allows for approximately 2.75 inches (70 mm) of maximu[...]
-
Seite 67
3. Press the SET ACCEL control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. Note: • V ehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to red[...]
-
Seite 68
Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the COAST control until you get to the desired speed, then release the control. Y ou can also use the COAST control to operate the T ap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 k[...]
-
Seite 69
STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Radio control features • Press MODE to select AM, FM1, FM2, T APE or CD (if equipped). In Radio mode: • Press NEXT to seek/scan to the next strong station. In T ape mode: • Press NEXT to listen to the next selection on the tape. [...]
-
Seite 70
When switched on by the operator they provide 10 amps or 30 amps of electrical battery power for a variety of personal or commercial uses. If your vehicle is equipped with this option, there will also be a relay box with a fuse located inside the glove box. The relays and fuse in the glove box are coded as shown in the accompanying illustration. 20[...]
-
Seite 71
There will also be one power lead for each switch found as a blunt-cut and sealed wire located behind the passenger compartment fuse panel. They are coded as follows: Switch Circuit number W ire color Fuse AUX 1 1936 Orange with Light Green T race 30A AUX 2 1933 Orange 30A AUX 3 1934 Orange with Y ellow T race 10A AUX 4 1935 Orange with Light Blue [...]
-
Seite 72
T o close the moon roof: Press and hold the control until the glass panel stops at the “comfort” position. Press and hold the control again until the glass stops moving. When fully closed, the rear portion of the glass panel will appear higher than the front portion. T o vent the moon roof: Press and hold the control. The moon roof must be in t[...]
-
Seite 73
Door ajar: Displays when the ignition is in the ON position and any door is open. Check fuel cap: Displays when the fuel cap may not be properly installed. Continued driving with this display on may cause the Service engine soon warning light to come on. Refer to Fuel filler cap under the Fuel Information section in the Maintenance and Specificatio[...]
-
Seite 74
Check trailer (if equipped): Displayed when a trailer connection becomes disconnected, either intentionally or unintentionally , and has been sensed during a given ignition cycle. Refer to Integrated trailer brake controller in the T ires, Wheels and Loading chapter for more information. Language The language options are English and French. The fea[...]
-
Seite 75
Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • Odometer/Compass • Tr i p Odometer/Odometer/Compass • Distance to Empty/Odometer/Compass • A verage Fuel Economy/Odometer/Compass • Engine hour meter/Odometer/C[...]
-
Seite 76
Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/ 100 km. If you calculate your average fuel economy by dividing miles traveled since last fill-up by gallons of fuel used (multiply liters used by 100, then divide by kilometers traveled), your figure may be different th[...]
-
Seite 77
Compass zone/calibration adjustment 1. Determine your magnetic zone by referring to the zone map. 2. T urn ignition to the ON position. 3. Start the engine. 4. From Info menu, press and hold the SETUP and RESET controls simultaneously until the message center display changes to show the current zone setting (XX). 5. Press the SETUP control repeated[...]
-
Seite 78
9. The compass is now calibrated. Engine hour meter Select this function from the INFO menu to display the accumulated running time of the engine. Setup menu Press this control for the following displays: • System Check • Units (English/Metric) • Autolock • Autolamp Delay • Language System check Selecting this function from the SETUP menu[...]
-
Seite 79
5. DOOR AJAR 6. FUEL CAP (gasoline engine only) 7. AIR FIL TER (diesel engine only) 8. FUEL LEVEL Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. Autolocks This feature automatically locks all vehicle doors when the vehicle is shif[...]
-
Seite 80
2. Pressing the RESET control cycles the message center through each of the language choices. 3. Press and hold the RESET control to set the language choice. System warnings System warnings alert you to possible problems or malfunctions in your vehicle’ s operating systems. In the event of a multiple warning situation, the message center will cyc[...]
-
Seite 81
W arning display Status Low fuel level W arning returns after 10 minutes Low brake fluid level Low oil pressure Check engine temperature T railer disconnected W ater in fuel (diesel only) Check air filter (diesel only) Door ajar W arning returns after the ignition key is turned from OFF to ON. Check fuel cap Engine failsafe mode Check compass modul[...]
-
Seite 82
CHECK ENGINE TEMPERA TURE Displayed when the engine coolant is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter . If the warning stays on or continues to come on, contact your authorized dealer as [...]
-
Seite 83
DA T A ERR These messages indicate improper operation of the vehicle network communication between electronic modules. • Odometer • Fuel flow • Fuel level • T rans temp • Fuel cap • Engine sensor • Brake fluid • Auto lock • Auto lamp delay Contact your authorized dealer as soon as possible if these messages occur on a regular basi[...]
-
Seite 84
T ailgate removal Y our tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw . Disconnect cable. 3. Disconnect the other cable. 4. Lift tailgate to a 45–degree angle. 5. Lift right side off of its hinge. 6. Lift left side off[...]
-
Seite 85
KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . POWER DOOR LOCKS (IF EQUIPPED) Press control to unlock all doors. Press control to lock all doors. Smart locks (if equipped) This feature prevents you from locking yourself out of the vehicle if yo[...]
-
Seite 86
[...]
-
Seite 87
6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. Note: Pressing the power door UNLOCK/LOCK button again will toggle between activating and deactivating the autolock feature. 7. T urn the ignition to the 3 (OFF) position. [...]
-
Seite 88
The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. Y our vehicle is equipped with a remote entry system which allows[...]
-
Seite 89
Power door lock disable feature (if equipped) The UNLOCK feature on your power door locks will not work from inside the vehicle when: • the ignition has been turned to the 3 (OFF) position, and • 20 seconds elapse after all vehicle doors are closed and locked using the remote entry transmitter , or the power door lock control (while the accompa[...]
-
Seite 90
2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery . Press the batt[...]
-
Seite 91
T o program the keyless entry keypads remote entry transmitters yourself: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. T urn the key from the 2 (LOCK) position to 3 (OFF). 4. Cycle eight times rapidly (within 10 seconds) between the 3 (OFF) position and 4 (ON). Note: The eighth turn must end in the 4 (ON) pos[...]
-
Seite 92
• the 7 • 8 and the 9 • 0 controls on the keyless entry keypad are pressed, or • after 25 seconds of illumination. The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door [...]
-
Seite 93
• The factory set code will work even if you have set your own personal code. • If you set a second personal code it will erase your first personal code. Erasing personal code 1. Enter the factory set 5–digit code. 2. W ithin five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold the 1 • 2 for two seconds. This must be[...]
-
Seite 94
SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Adjustable head restraints (if equipped) The purpose of these head restraints[...]
-
Seite 95
Full bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Pull up on the lever located at the bottom of the seatback to quickly fold the seatback forward. • Pull up on the lever located at the side of the seat cushion to recline the seatback and to return the sea[...]
-
Seite 96
40/20/40 front seat armrest and console (if equipped) T o release the armrest, pull forward on the strap and pull the armrest down. T o gain access to the storage compartment in your armrest, lift the latch to open the lid. The lid cannot be opened in the upright position. Lift up armrest to return it to a center seatback. 2007 F-250/350/450/550 (f[...]
-
Seite 97
Captain’ s chair (if equipped) • Lift the bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • T o recline the seatback, pull the release lever handle located on the side of the seat up. • Push down the lever (if equipped) located at the bottom of the seatback to quickly fold the seatback forward. Adj[...]
-
Seite 98
Press to raise or lower the rear portion of the seat cushion. • T ype A • T ype B Press the control to move the seat forward, backward, up or down. • T ype A • T ype B 2007 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Seating and Safety Restraints 98[...]
-
Seite 99
Using the manual lumbar support For more lumbar support, turn the lumbar support control toward the front of vehicle. For less lumbar support, turn the lumbar support control toward the rear of vehicle. Heated seats (if equipped) T o operate the heated seats, do the following: • Push control to activate. • Push again to deactivate. The indicato[...]
-
Seite 100
REAR FOLDING SEAT SYSTEM WITH LOAD FLOOR (IF EQUIPPED) The rear seatback has a split 60/40 seat. Each seat cushion can be flipped up into the seatback position. 1. Pull down the latch lever located on the bottom seat back to fold the seat back forward. 2. Pull up on the lever located on the side of the seat cushion to rotate the cushion up until it[...]
-
Seite 101
T o gain access to the cupholders and tray , pull down on the armrest. T o gain access to the 60/40 load floor , store the cushion in the upright locked position. Pull up on the straps located at the sides of the load floor , and rotate forward until resting on the carpet. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with y[...]
-
Seite 102
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety [...]
-
Seite 103
Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle. The front outboard and r[...]
-
Seite 104
Automatic locking mode When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. This mode should be used any time a child safety seat is installed, except a booster ,[...]
-
Seite 105
After any vehicle collision, the front passenger and rear outboard seat belt systems must be checked by your authorized dealer to verify that the “automatic locking retractor” feature for child seats is still functioning properly . In addition, all seat belts should be checked for proper function. BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED [...]
-
Seite 106
• Regular Cab and 4–door Crew Cab • 4–door Super Cab T o adjust the shoulder belt height, push the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place. Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around the hips[...]
-
Seite 107
Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and[...]
-
Seite 108
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.[...]
-
Seite 109
If... Then... The driver’ s safety belt is buckled before the ignition switch is turned to the ON position... The BeltMinder 威 feature will not activate. The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur eve[...]
-
Seite 110
Reasons given... Consider ... “The people I’m with don’t wear belts” Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see. “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed[...]
-
Seite 111
• the driver’ s safety belt is unbuckled • the parklamps/headlamps are in the OFF position (If the vehicle is equipped with Autolamps, this will not affect the procedure) While the design allows you to deactivate your BeltMinder 威 ,t h i s system is designed to improve your chances of being safely belted and surviving an accident. W e recom[...]
-
Seite 112
Safety belt extension assembly If the safety belt is too short when fully extended, there i sa8i n c h( 2 0 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your authorized dealer . Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is lo[...]
-
Seite 113
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag. All occupants of the vehicle, including the driver , should alw[...]
-
Seite 114
Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. T o properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably . • Recline the seat slightly one or two degrees from the upright position. Do [...]
-
Seite 115
Children must always be properly restrained. Failure to follow these instructions may increase the risk of injury in a collision. An infant in a rear -facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unless the passenger airbag is turned[...]
-
Seite 116
restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control. Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deploye[...]
-
Seite 117
Disposal of airbags and airbag equipped vehicles See your local authorized dealer . Airbags MUST BE disposed of by qualified personnel. Passenger airbag ON/OFF switch (if equipped) An airbag ON/OFF switch has been installed in this vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper position in acco[...]
-
Seite 118
An infant in a rear -facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unless the passenger airbag is turned off. Turning the passenger airbag back on The passenger airbag remains OFF until you turn it back ON. 1. Insert the ignition key [...]
-
Seite 119
If your vehicle has rear seats, always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly . If a child in a rear facing infant seat must be transported in front, the passenger airbag must be turned OFF . This is because the back of the infant seat is too close to the inflating airbag an[...]
-
Seite 120
• the child has a medical condition which, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’ s condition. 3. Medical condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger airbag to pose[...]
-
Seite 121
• the child has a medical condition that, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can monitor the child’ s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a special risk for the passenger if the ai[...]
-
Seite 122
Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. Children and safety belts If the child is the proper size, restrain the child in a safety seat. C[...]
-
Seite 123
When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly . Generally this is when they weigh about 80 lb. (36 kg) (about 8 to 12 years old). Booster seats should be used until you can answer YES to ALL of[...]
-
Seite 124
• Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’ s head, a high back booster seat would be a better choice. Either type can be used at any seating position equipped with lap/shoulder belts if your child is over 40 lb. (18 kg). Children and booster seats vary wide[...]
-
Seite 125
Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’ s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or towels to boost a child. They can slide around a[...]
-
Seite 126
• T op tether anchors can be used for children up to 60 pounds (27 kg) in a child restraint, and to provide upper torso restraint for children up to 80 pounds (36 kg) using an upper torso harness and a belt-positioning booster . Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating po[...]
-
Seite 127
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]
-
Seite 128
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]
-
Seite 129
Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. T[...]
-
Seite 130
• F-Series Crew Cab T ether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position. 4. Y ou may need to pull the seatback forward to access the tether anchors. Make sure the seat is locked in the u[...]
-
Seite 131
• Rear seats (Crew Cab) If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 6. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat. 7. T ighten the [...]
-
Seite 132
1. Route the tether strap through the loop directly behind the child seat. 2. Attach the strap hook onto the loop behind an adjacent seating position. 3. Install the child safety seat tightly using the vehicle belts. Follow the instructions in this chapter . 4. T ighten the tether strap according to the child seat manufacturer’ s instructions. A [...]
-
Seite 133
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]
-
Seite 134
Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on shifting procedures and maintenance can be found in your Owner’ s Guide .Y o u should become thoroughly familiar with this information before you operate your vehicle. On some 4W[...]
-
Seite 135
• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versa[...]
-
Seite 136
government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however , and may depart significantly from the norm due to variations in driving habits, service practices, a[...]
-
Seite 137
• T ire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a[...]
-
Seite 138
At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company . Use a tire gauge to check the tire inflation pressure, including the spare (if equipped), at least monthly and before long trips.[...]
-
Seite 139
T o check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recomme[...]
-
Seite 140
Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, they cannot be treated like normal light truck tires. T ire service, including adjusting the air pressure, must be performed by personnel trained, supervised and equipped according to Federal Occupational Sa[...]
-
Seite 141
Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Al[...]
-
Seite 142
Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydropla[...]
-
Seite 143
U.S. DOT Tire Identification Number (TIN) U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification and [...]
-
Seite 144
When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi greater than t[...]
-
Seite 145
Highway hazards No matter how carefully you drive there’ s always the possibility that you may eventually have a flat tire on the highway . Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect[...]
-
Seite 146
• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD) (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask your authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y [...]
-
Seite 147
• DRW – Six tire rotation If your vehicle is equipped with dual rear wheels it is recommended that the front and rear tires (in pairs) be rotated only side to side. W e do not recommend splitting up the dual rear wheels. Rotate them side to side as a set/pair . After tire rotation, inflation pressures must be adjusted for the tires new position[...]
-
Seite 148
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the T ire and Rim Association (T&RA), that[...]
-
Seite 149
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186[...]
-
Seite 150
12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire grad[...]
-
Seite 151
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/L[...]
-
Seite 152
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and Rim A[...]
-
Seite 153
SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. Note: Do not use snow chains on front tires of vehicles with 20” wheels and tires. The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and[...]
-
Seite 154
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label (vehicles exported outside the U.S. and Canada may not have a T ire Label) on the B-Pillar or the edge of the driver’ s door . Look for “THE COMBINED WEIGHT OF OCCUP ANTS AND CARGO SHOULD [...]
-
Seite 155
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2007 F[...]
-
Seite 156
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Exceeding the Safety Compliance Certif[...]
-
Seite 157
GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The GVW must never exceed the GVWR. GCW (Gross Combined W eight) ?[...]
-
Seite 158
T ongue Load or Fifth Wheel King Pin W eight – refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5,000 lb. (2,268 kg) conventional trailer , multiply 5,000 by 0.10 and 0.15 to obtain a proper tongue load range of 500 to 750 lb. (227 to 340 kg). For an 11,500 lb. (5,216 kg) fifth wheel trailer , mult[...]
-
Seite 159
The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity: • Another example for your vehicle with 1,400 lb. (635 kg) of cargo and luggage capacity . Y ou decide to go golfing. Is there enough load capacity to carry you, 4 of your friends and all the golf bags? Y ou and four friends average[...]
-
Seite 160
Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Y our vehicle can haul more cargo and people than most passenger cars. Depending upon the type and placement of the load, hauling cargo and people may raise t[...]
-
Seite 161
Note: Do not exceed the GCWR listed for your vehicle on the following chart/table, or the GVWR, GA WR or tire ratings specified on the Tire Label or Safety Compliance Certification Label. T owing trailers beyond the maximum recommended trailer weight which exceeds the limit of the vehicle’ s GCWR, GVWR, GA WR or tire ratings could result in engin[...]
-
Seite 162
Integrated hitch rating The standard integrated hitch has two ratings depending on mode of operation: • W eight carrying - requires a draw bar and hitch ball. The draw bar supports all the vertical tongue load of the trailer . • W eight distributing - requires an aftermarket weight distributing system which includes draw bar , hitch ball, sprin[...]
-
Seite 163
Weight distributing hitch When hooking up a trailer using a weight distributing hitch, always use the following procedure: 1. Park the unloaded vehicle on a level surface. W ith the ignition on and all doors closed, allow the vehicle to stand for several minutes so that it can level. 2. Measure the height of a reference point on the front and rear [...]
-
Seite 164
Integrated trailer brake controller (if equipped) Y our vehicle may be equipped with a fully integrated electronic T railer Brake Controller (TBC). When used properly , the TBC helps ensure smooth and effective trailer braking by powering the trailer’ s electric brakes with a proportional output based on the towing vehicle’ s brake pressure. Th[...]
-
Seite 165
3. GAIN setting display: Shows the current GAIN setting. This will illuminate when a trailer is connected, flash if the trailer becomes disconnected, or remain off if no trailer is connected. 4. OUTPUT bar graph: When the vehicle’ s brake pedal is pushed, or when the manual control is activated, green bar indicators will illuminate to indicate th[...]
-
Seite 166
5. In a traffic-free environment, tow the trailer on a dry , level surface at a speed of 20 – 25 mph (30 – 40 km/h) and squeeze the manual control lever completely . 6. If the trailer wheels lock-up (indicated by squealing tires), reduce the GAIN setting; if the trailer wheels turn freely , increase the GAIN setting. Repeat Steps 5 and 6 until [...]
-
Seite 167
Points to Remember: • Remember to adjust gain setting before using the TBC for the first time. • Readjust GAIN setting on the TBC (according to procedure above) whenever road, weather and trailer or vehicle loading conditions change from those that existed when the gain was initially set. • The sliding lever on the TBC should be used only for[...]
-
Seite 168
Driving while you tow When towing a trailer: • Do not drive faster than 70 mph (112 km/h) during the first 500 miles (800 km) of trailer towing and don’t make full-throttle starts. • T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed r[...]
-
Seite 169
refilling your rear axle with synthetic gear lubricant if not already so equipped. Refer to Maintenance Product Specifications and Capacities in the Maintenance and Specifications chapter for the proper axle lubricant. Remember that regardless of the rear axle lubricant used, do not tow a trailer for the first 500 miles (800 km) of a new vehicle, a[...]
-
Seite 170
Tires • All trailer tires should be of the same size, and construction. • Select tires that meet the trailer loading requirements. • Always check tow vehicle and trailer tire pressure before towing. Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not allow the static water level to rise above[...]
-
Seite 171
4x4 with manual shift transfer case: • Place the transfer case in N (Neutral). • Front hub locks are in the FREE position. 4x4 electronic shift transfer case vehicles with automatic transmissions: Regarding recreational towing or having your vehicle towed, 4x4 vehicles with electronic shift on the fly cannot be towed with any wheels on the grou[...]
-
Seite 172
STARTING Positions of the ignition 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. For vehicles equipped with a manual transmission, you must depress the ignition release lever to release t[...]
-
Seite 173
Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehi[...]
-
Seite 174
If starting a vehicle with an automatic transmission: 1. Make sure the parking brake is set. 2. Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: 1. Make sure the parking brake is set. 2. Push the clutch pedal to the floor . 2007 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Driving 174[...]
-
Seite 175
• T urn the key to 4 (ON) without turning the key to 5 (ST ART). 1 2 3 4 5 2007 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Driving 175[...]
-
Seite 176
Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. Starting the engine 1. T urn the key to 4 (ON) without turning the key to 5 (ST ART). 2. T urn the key to 5 (ST ART), then release the key as s[...]
-
Seite 177
Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.5 cm) or adjust the heating or air conditioning to bring in fresh air . USING THE ENGINE BLOCK HEATER (IF EQUIPPED) Use of an engine block heater is strongly recommended if you live in a region wher[...]
-
Seite 178
Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking. Noise from the ABS pump motor and brake pedal pulsation may be observed during ABS braking and the brake pedal may suddenly travel a litt[...]
-
Seite 179
Parking brake T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated until the parking brake is released. Pull the right side of the release lever to release the parking brake; the release lever pulls at an angle toward the driver’ s[...]
-
Seite 180
Note: If your vehicle is equipped with a manual transmission, the engine may be required to run while power accessories operate and the parking brake is set. It is recommended that wheel chocks be used during this operation. If you’re parking your vehicle on a grade or with a trailer , press and hold the brake pedal down, then set the parking bra[...]
-
Seite 181
A high crown in the road or high crosswinds may also make the steering seem to wander/pull. T RACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the T raction-Lok axle functions like a standard rear axle. The axle may exhibit a sl[...]
-
Seite 182
AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the 4 (ON) position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the 4[...]
-
Seite 183
Understanding the shift positions of the 5–speed automatic transmission This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality . When the vehicle’ s battery has been disconnected for any type of service or repair , the transmission will need to[...]
-
Seite 184
N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Overdrive) with T ow/Haul OFF D (Overdrive) with T ow/Haul OFF is the normal driving position for the best fuel economy . The overdrive function allows automatic upshifts and downshifts through g[...]
-
Seite 185
3 (Third) T ransmission starts and operates in third gear only . Used for improved traction on slippery roads. Selecting 3 (Third) provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearsh[...]
-
Seite 186
T o start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor , then put the gearshift lever in the neutral position. 3. Start the engine. 4. Press the brake pedal and move the gearshift lever to the desired gear; 1 (First) or R (Reverse). 5. Release the parking brake, then slowly release the clutch peda[...]
-
Seite 187
Maximum downshift speeds 1 6-speed transmission Shift from: T ransfer case position (if equipped) 2 2H or 4H 4L D (Overdrive) - 4 45 mph (72 km/h) 16 mph (26 km/h) 4-3 35 mph (56 km/h) 12 mph (19 km/h) 3-2 20 mph (32 km/h) 8 mph (13 km/h) 2-1 5 mph (8 km/h) 2 mph (3 km/h) 1-LO Only shift to LO when at a stop. 1 Use 2H or 4H for 4WD equipped vehicle[...]
-
Seite 188
Removing the key T urn the ignition off, push the release lever (located above the ignition), then turn the key toward you and remove the key . REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) is selected and the vehicle is moving at speeds [...]
-
Seite 189
The RSS detects obstacles up to 6 feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away , the tone will sound conti[...]
-
Seite 190
If your vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this [...]
-
Seite 191
LOW (4WD Low) can be engaged, the vehicle speed must be below 3 mph (5 km/h) with the brake pedal depressed and the transmission in N (Neutral). This vehicle is equipped with a non-synchronous low range gearset which will not allow the transfer case to shift into 4X4 LOW (4WD Low) if vehicle speed is above 3 mph (5 km/h). It is recommended that a s[...]
-
Seite 192
• LOW RANGE – momentarily illuminates when the ignition is turned to the ON position. Illuminates when 4L (4x4 Low) is engaged. Using a Manual Shift On Stop (MSOS) 4WD system (if equipped) Note: Some noise may be heard as the 4WD system shifts or engages. This is normal. 2H (2WD High) – For general on-road driving. Sends power to the rear whe[...]
-
Seite 193
Shifting from 4H (4WD High) to 2H (2WD High) Move the transfer case lever to 2H (2WD High) at a stop or a vehicle speed below 3 mph (5 km/h). W ith the vehicle at complete stop, disengage the locking hubs (optional) by rotating the hub lock control from LOCK to FREE. • For proper operation, make sure that both indicator arrows on the hub are alig[...]
-
Seite 194
Using the N (Neutral) position The transfer case neutral position overrides the transmission and puts the vehicle in neutral regardless of transmission gearshift lever position. The vehicle can move forward or backwards. This position should only be used when towing the vehicle. Do not leave the vehicle unattended with the transfer case in the N (N[...]
-
Seite 195
Shifting from 2WD (2WD High) to 4x4 HIGH (4WD High) Rotate the 4WD control to the 4x4 HIGH position at speeds up to 55 mph (88 km/h). • The electronic shift 4WD system is designed to engage 4x4 HIGH (4WD High) when the vehicle is moving. If shifted to 4x4 HIGH (4WD HIGH) while at complete stop, 4x4 may not engage and the 4x4 indicator may not ill[...]
-
Seite 196
4. Move the 4WD control to the 4x4 LOW position. 5. Hold the shift conditions until the LOW RANGE indicator light illuminates. 6. If the LOW RANGE indicator light does not illuminate within 15 seconds, allow the vehicle to move at a speed above 1 mph (1.6 km/h), then repeat steps 3 through 5 before reporting any shift concerns to your authorized de[...]
-
Seite 197
Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. Y ou should either know the t[...]
-
Seite 198
V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road[...]
-
Seite 199
V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road[...]
-
Seite 200
can be found in the Maintenance and Specifications chapter . Y ou should become thoroughly familiar with this information before you operate your vehicle. Normal characteristics On some 4WD models, the initial shift from two-wheel drive to 4x4 while the vehicle is moving can cause some momentary clunk and ratcheting sounds. This is the front drivet[...]
-
Seite 201
Refer to T ransmission temperature gauge in the Instrument Cluster chapter for transmission fluid temperature information. If the front or rear axle is submerged in water , the axle lubricant should be replaced. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts c[...]
-
Seite 202
Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, manually shift to a lower gear . Y our vehicle has anti-lock brakes, apply the brakes steadily . Do not “pump” the brakes. Driving on snow and ice 4WD vehicles have advantages over 2W[...]
-
Seite 203
Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carrying capability . For this reason, Ford Motor Company strongly recommends that you do not make modifications such as adding or removing parts (such as lift ki[...]
-
Seite 204
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water , traction or brake capability may be limited. Also, wate[...]
-
Seite 205
• Rear ballast weight behind the rear axle may be required to prevent exceeding the FGA WR, and provide front-to-rear weight balance for proper braking and steering. • Front wheel toe may require re-adjustment to prevent premature uneven tire wear . Specifications are found in the Ford W orkshop Manual. • Headlight aim may require re-adjustme[...]
-
Seite 206
All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. Never remove or defeat the “tripping mechanisms” designed into the snow removal equipment by its manufacturer . Doing so may cause damage to the vehicle and the snow removal e[...]
-
Seite 207
Do not spin the wheels at over 35 mph (55 km/h). The tires may fail and injure a passenger or bystander . Removing the snowplow frame mount A metal crossmember is included below the front bumper on Super Duty vehicles called a “BlockerBeam”. T ypical snowplow installations require removal of this BlockerBeam to install the snowplow mounting har[...]
-
Seite 208
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the New V ehicle Limited W arranty perio[...]
-
Seite 209
Canadian customers refer to your Owner Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick refer[...]
-
Seite 210
HAZARD FLASHER The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it whe[...]
-
Seite 211
This switch is located in the front passenger’ s footwell, behind the kick panel access cover . T o reset the switch: 1. T urn the ignition off. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. T urn the ignition on. 5. W ait a few seconds and return the key to off. 6. Make an[...]
-
Seite 212
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]
-
Seite 213
T o remove a fuse use the fuse puller tool provided on the fuse panel cover . T o reinstall the cover , align and engage the two hooked clips at the bottom of the cover onto the instrument panel, then lift the panel and press the top clips firmly into place. Always disconnect the battery before servicing high current fuses. Always replace the cover[...]
-
Seite 214
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A* Adjustable pedals 2 10A* Cluster 3 10A* Upfitter #3 4 20A* Power point (Instrument panel) 5 10A* Upfitter #4 6 — Not used 7 30A* High beam headlamps, Flash-to-pass 8 20A* Back-up lamps 9 — Not used 10 — Not used 11 20A* Radi[...]
-
Seite 215
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 15 — Not used 16 — Not used 17 15A* Exterior lamps 18 20A* Flasher , Brake On-Off (BOO) lamps 19 10A* Body Security Module (BSM) (Security) 20 15A* T railer tow Electric Brake Controller (EBC) 21 20A* Heated seats 22 20A* Engine control 23 20A* Engine control (gaso[...]
-
Seite 216
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 40 20A* Fuel pump 41 10A* Instrument cluster 42 15A* Delayed accessory 43 10A* Fog lamps 44 — Not used 45 10A* Ignition switch RUN/ST ART feed 46 10A* Left-hand low beam headlamp 47 10A* Right-hand low beam headlamp 48 — Not used 101 30A** T railer tow EBC 102 30A*[...]
-
Seite 217
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 304 — Not used 305 Full ISO relay Upfitter control 306 Full ISO relay Delayed accessory 307 Full ISO relay Starter 601 30A circuit breaker Delayed accessory , Power windows, Moonroof 602 — Not used * Mini fuse ** Cartridge fuse Power distribution box The power dist[...]
-
Seite 218
The high-current fuses and relays are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 30A* W ipers 2 40A* Blower 3 30A* Electronic Shift on the Fly (ESOF) 4 — Not used 5 50A* Injector Driver Module (IDM) (Diesel engine only) 6 — Not used 7 — Not used 8 — Shunt 9 20A** T railer tow turn signals 10 1[...]
-
Seite 219
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 14 — Not used 15 15A** IDM logic (Diesel engine only) 16 — Not used 17 10A** A/C clutch 18 10A** IDM relay (Diesel engine only) 19 — Not used 20 10A** T railer tow back-up lamps 21 — Not used 22 60A*** ABS (Coils) 23 60A*** ABS (Pump) 201 1 ⁄ 2 ISO relay T railer tow r[...]
-
Seite 220
Relays An auxiliary relay box is located in the left-hand front side of the engine compartment. This box contains relays for the Electronic Shift On the Fly (ESOF) system. Please see your authorized dealer for troubleshooting or service of these relays. CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily . • gradua[...]
-
Seite 221
A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T -type mini-spare: This spare tire begins with the letter “T” for tire size and may have “T emporary Use Only” molded in the sidewall 2. Full-size dissimilar s[...]
-
Seite 222
The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability • All-Wheel driving capability (if applicable) • Load leveling ad[...]
-
Seite 223
• Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability Location of the spare tire and tools If your vehicle is equipped with a spare tire, jack and associated tools, refer to the following table for their locations: T ool Location Spare tire (pick-up trucks only) Under the vehicle, just [...]
-
Seite 224
• one wheel nut wrench. Slide over square end of jack handle. • V ehicles equipped with dual rear wheels, insert the lug wrench extension into the lug wrench to reach the lug nuts. 2. Attach the spare tire lock key (A) to the jack handle (B). 3. Fully insert the jack handle through the bumper hole and into the guide tube. The key and lock will [...]
-
Seite 225
Tire change procedure 1. Park on a level surface, activate hazard flashers and set the parking brake. • Automatic transmission: Place gearshift lever in P (Park). • Manual transmission: Place gearshift lever in R (Reverse). • Electronic Shift-On-the-Fly (ESOF) 4WD: Place transfer case in any position. • Manual shift transfer case 4WD: Place[...]
-
Seite 226
If the vehicle slips off the jack, you or someone else could be seriously injured. The following steps apply to F–250/F–350 Single Rear Wheel (SR W) vehicles only(unless otherwise noted): 6. Insert the hooked end of the jack handle into the jack and use the handle to slide the jack under the vehicle. 7. Position the jack according to the follow[...]
-
Seite 227
• Front passenger side (4x4) Note: View shown from the rear of the vehicle to clearly identify the jack point. Place the jack directly under the axle. • Rear (including F-350 Dual Rear wheel [DRW] vehicles) Never use the front or rear differential as a jacking point. T o lessen the risk of personal injury , do not put any part of your body unde[...]
-
Seite 228
10. Replace the flat tire with the spare tire, making sure the valve stem is facing outward for all front wheels and single rear wheel vehicles. If replacing an inboard rear tire on dual rear wheel vehicles, the valve stem must be facing outward. If replacing the outboard wheel, the valve stem must be facing inward. Reinstall the lug nuts until the[...]
-
Seite 229
• Front passenger side (4x4): F-350 DRW Note: View shown from the rear of the vehicle to clearly identify the jack point. Note: Place the jack directly under axle and inboard of the radius arm so that the jack clears the radius arm. • Front: F–450/F–550 • Rear: F-450/F-550 14. Insert the jack handle into the pump linkage. 15. Use an up-an[...]
-
Seite 230
17. Replace the flat tire with the spare tire, making sure the valve stem is facing outward on all front an inboard rear wheels. If replacing the outboard wheel, the valve stem must be facing inward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 18. Lower the whee[...]
-
Seite 231
20. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicle is equipped with a spare tire carrier . Note: Do not stow the Harley-Davidson flat tire and wheel using the spare tire winch mechanism; store the flat in the bed of the truck. 21. Stow the jack, jack handle and lug wrench. Make sure the jack is securely fastened so it does [...]
-
Seite 232
WHEEL LUG NUT TORQUE SPECIFICATIONS On vehicles equipped with single rear wheels, retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.). On vehicles equipped with dual rear wheels, retighten the wheel lug nuts to the specified torque at 100 miles ([...]
-
Seite 233
JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do[...]
-
Seite 234
Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . + – + – + ?[...]
-
Seite 235
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding [...]
-
Seite 236
3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to d[...]
-
Seite 237
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]
-
Seite 238
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground using a wheel lift On 4x4 vehi[...]
-
Seite 239
Note: T owing an a 4x2 or an ESOF 4WD vehicle with the rear wheels on the ground for more than 50 miles (80 km) and/or in excess of 35 mph (56 km/h) may cause damage to the automatic transmission. Note: On Dual Rear Wheel (DRW) vehicles, an outer rear wheel must be removed prior to using a wheel lift wrecker . If the vehicle is towed by other means[...]
-
Seite 240
GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repair[...]
-
Seite 241
In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, c[...]
-
Seite 242
In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent a[...]
-
Seite 243
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide. However , if your warranty conc[...]
-
Seite 244
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]
-
Seite 245
If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .ford-esp.com. GETTING ASSIST A[...]
-
Seite 246
ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: w[...]
-
Seite 247
T o contact NHTSA, you may call the V ehicle Safety Hotline toll-free at 1–888–327–4236 (TTY : 1–800–424–9153); go to http://www.safercar .gov; or write to: Administrator NHTSA 400 Seventh Street, SW W ashington, D.C. 20590 Y ou can also obtain other information about motor vehicle safety from http://www.safercar .gov. REPORTING SAFETY [...]
-
Seite 248
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Ne[...]
-
Seite 249
racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Y our authorized dealer has touch-up paint and sprays to match your vehicle’ s color . T ake your color code (printed on a sticker in the driver’ s door jamb) to your authorized dealer to ensure[...]
-
Seite 250
• Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. • Cover the highlighted areas to prevent water damage when cleaning the engine. • 5.4L V8 gasoline engine • 6.8L V10 gasoline engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These produc[...]
-
Seite 251
• For routine cleaning, use Motorcraft Detail W ash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and T ar Remover (ZC-42). • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray Glass Cleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularl[...]
-
Seite 252
INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then dry by wiping with a dry , soft, clean cloth. • Do not use household or glass cleaners as these may damage the finish. INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner . • Remove light stains and soil with Moto[...]
-
Seite 253
LEATHER SEATS FOR THE KING RANCH F-250 AND F-350 CREWCAB ONLY (IF EQUIPPED) Y our vehicle is equipped with seating covered in premium, top-grain leather which is extremely durable, but still requires special care and maintenance in order to ensure longevity and comfort. Regular cleaning and conditioning will maintain the appearance of the leather .[...]
-
Seite 254
Conditioning Bottles of King Ranch Leather Conditioner are available at the King Ranch Saddle Shop. Visit the W eb site at www.krsaddleshop.com ,o r telephone (in the United States) 1–800–282–KING (5464). If you are unable to obtain King Ranch Leather Conditioner , use another premium leather conditioner . • Apply your first conditioning tr[...]
-
Seite 255
Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A) Motorcraft Detail W ash (ZC-3–A) Motorcraft Dusting Cloth (ZC-24) Motorcraft Engine Shampoo and Degreaser (U.S only) (ZC-20) Motorcraft Engine Shampoo (Canada only) (CXC-66-A) Motorcraft One Step W ash and W ax Concentrate (ZC-6-A) Mo[...]
-
Seite 256
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a scheduled maintenance guide which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Ch[...]
-
Seite 257
2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the b[...]
-
Seite 258
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Refer to the 6.0 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for diesel engine component locations. 5.4L V8 gasoline engines 1. T ransmission fluid dipstick (automatic transmission) 2. Air filter assembly 3. Engine coolant reservoir 4. Brake fluid reservoir 5. Clutch[...]
-
Seite 259
6.8L V10 gasoline engine Refer to the 6.0 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for diesel engine component locations. 1. T ransmission fluid dipstick (automatic transmission) 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Clutch fluid reservoir (manual transmission) 5. Power distribution box 6. Powe[...]
-
Seite 260
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellant-type fluid or bug wash as this may cause a squeaking/chattering noise[...]
-
Seite 261
4. Poor wiper quality can be improved by cleaning the wiper blades and the windshield; refer to Windows and wiper blades in the Cleaning chapter . 5. T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro [...]
-
Seite 262
• 5.4L V8 engine • 6.8L V10 engine 2007 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 262[...]
-
Seite 263
6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some o[...]
-
Seite 264
Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the Internatio[...]
-
Seite 265
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Als[...]
-
Seite 266
When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. A [...]
-
Seite 267
If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about [...]
-
Seite 268
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to the scheduled maintenance information for service interval schedules. • Be sure to [...]
-
Seite 269
Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it difficult to see throug[...]
-
Seite 270
T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly . 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth aroun[...]
-
Seite 271
Used engine coolant should be disposed of in an appropriate manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Maintenance Product Specifications and Capacities in this section. If your[...]
-
Seite 272
V ehicles driven year -round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. What you should know about fail-safe cooling (if equipped) If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental compo[...]
-
Seite 273
2. Arrange for the vehicle to be taken to a service facility . 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low . Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to a service facility . Driving the vehicle w[...]
-
Seite 274
Gasoline may contain benzene, which is a cancer -causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is [...]
-
Seite 275
The flow of fuel through a fuel pump nozzle can produce static electricity , which can cause a fire if fuel is pumped into an ungrounded fuel container . Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in th[...]
-
Seite 276
If the “Check Fuel Cap” indicator comes on and stays on after you start the engine, the fuel filler cap may not be properly installed. T urn off the engine, remove the fuel filler cap, align the cap properly and reinstall it. If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The vehicl[...]
-
Seite 277
regular grade fuel. In Canada, many fuels contain metallic additives, but fuels free of such additives may be available; check with your local fuel dealer . Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty . Octane recommendations Y our vehicle is designed to use “Regular?[...]
-
Seite 278
Running out of fuel A void running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a f[...]
-
Seite 279
For consistent results when filling the fuel tank: • T urn the engine/ignition off prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low-medium-high) each time the tank is filled. • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the rec[...]
-
Seite 280
Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel e[...]
-
Seite 281
• Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy . • Using fuel blended with alcohol may lower fuel economy . • Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat te[...]
-
Seite 282
If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability . Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emis[...]
-
Seite 283
3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter . 4. Driving through deep water - the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tightening the fuel cap or letting the electrical system dry out. After three driving cy[...]
-
Seite 284
• Gasoline engine shown; diesel engine similar . Refer to Identifying components in the engine compartment in the 6.0/6.4 Liter Power Stroke Direct Injection T urbo Diesel Owner Guide Supplement. Check the fluid level when it is at ambient temperature, 20°F–80°F (-7°C–25°C): 1. Check the fluid level on the dipstick. It should be between t[...]
-
Seite 285
BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range the performance of your brake system could [...]
-
Seite 286
1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir . 2. Remove cap and rubber diaphragm from reservoir . 3. Add fluid until the level reaches the step in the reservoir . 4. Reinstall rubber diaphragm and cap onto reservoir . T RANSMISSION FLUID Checking automatic transmission fluid (if equipped) Refer to[...]
-
Seite 287
Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 50°F (10°C). Correct fluid level The transmission fluid should be checked at normal operating temperature 150°F-170°F (66°C-77°C) on a level surface. The normal operating temperature can be reached after approximat[...]
-
Seite 288
If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result i[...]
-
Seite 289
Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Us[...]
-
Seite 290
T RANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to Maintenance Product Specifications and Capacities in this chapter . D[...]
-
Seite 291
The following procedure is for vehicles equipped with a gasoline engine. If your vehicle is equipped with a diesel engine, refer to the 6.0/6.4Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air f[...]
-
Seite 292
3. Install a new air filter element into the tray assembly . 4. Return air filter tray to original position by pressing firmly on the handle until all rearward movement stops and secure the two clamps. • 6.8L Engine 1. Loosen the clamps that secures the air filter cover in place. 2. Carefully separate the two halves of the air filter housing. 3. [...]
-
Seite 293
MOTORCRAFT PART NUMBERS Component 5.4L V8 engine 6.8L V10 engine Air filter element F A-1754 F A-1782 Fuel filter FG-1011 Oil filter FL-820-S PCV valve 1 Battery (Standard) BXT -65-650 Battery (Optional) BXT -65-750 Spark plugs-platinum 2 Remote Automatic T ransmission Filter 3 FT -145 1 The PCV valve is a critical emission component. It is one of [...]
-
Seite 294
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name Ford part number / Ford specification Front axle 5.8 pints (2.8L) Motorcraft SAE 80W -90 Premium Rear Axle Lubricant XY -80W -90–QL / WSP-M2C197–A Spindle bearing — High T emperature 4X4 Front Axle and Wheel Bearing Grease E8TZ-19590–A XG-11 (F AD) / ESA-M1C198?[...]
-
Seite 295
Item Capacity Ford part name Ford part number / Ford specification Engine coolant - diesel engine Refer to the 6.0 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement Engine oil (includes filter change) - 5.4L V8 and 6.8L V10 gas engines 6 7.0 quarts (6.6L) Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil (US) Motor[...]
-
Seite 296
Item Capacity Ford part name Ford part number / Ford specification T ransmission / parking brake linkages and pivots, brake and clutch pedal shaft (if equipped) — Motorcraft Premium Long-Life Grease XG-1-C or XG-1-K / WSD-M1C227-A Power steering fluid Fill to FULL COLD range on dipstick Motorcraft MERCON 威 AT F XT -2-QDX / MERCON 威 T ransfer [...]
-
Seite 297
MERCON 威 , MERCON 威 V and MERCON 威 SP are not interchangeable. DO NOT mix MERCON 威 , MERCON 威 V and MERCON 威 SP . Use of dual usage fluids in an automatic transmission application requiring MERCON 威 SP may cause transmission damage. Use of a transmission fluid other than the recommended fluid may cause transmission damage. 4 Service r[...]
-
Seite 298
ENGINE DATA Engine 5.4L V8 engine 6.8L V10 engine Cubic inches 330 415 Required fuel 87 octane 87 octane Firing order 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9 Spark plug gap 1.02–1.28mm (0.040–0.050 inch)* 1.02–1.28mm (0.040–0.050 inch)* Ignition system Coil on plug Coil on plug Compression ratio 9.8:1 9.2:1 *The 5.4L 3V and 6.8L 3V spark plug [...]
-
Seite 299
IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]
-
Seite 300
1. W orld manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSION/T RANSAXLE CODE DESIGNATIONS Y ou can find a transmission/transaxle code on the vehicle Safety Compliance Certification L[...]
-
Seite 301
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada authorized dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic [...]
-
Seite 302
Interior style Consoles Electrochromatic compass/temperature interior mirrors Floor mats Lifestyle Ash cup / smoker’ s package Bedliners and bedmats Cargo organization and management T owing mirrors T railer hitches, wiring harnesses and accessories Peace of mind Mobile-ease 娂 hands-free communication system Remote start V ehicle security syste[...]
-
Seite 303
• T o avoid interference with other vehicle functions, such as anti-lock braking systems, amateur radio users who install radios and antennas onto their vehicle should not locate the Amateur Radio Antennas in the area of the driver’ s side hood. • Electrical or electronic accessories or components that are added to the vehicle by the authoriz[...]
-
Seite 304
A Accessory delay ..........................63 Air cleaner filter ....... 290–291, 293 Air conditioning ..........................41 Airbag supplemental restraint system ........................................ 113 and child safety seats ............ 114 description .............................. 113 disposal .................................... [...]
-
Seite 305
Climate control (see Air conditioning or Heating) ............ 41 Clutch fluid .......................................... 285 operation while driving .......... 185 recommended shift speeds .... 186 Compass, electronic set zone adjustment .................77 Console ........................................ 72 overhead ..............................[...]
-
Seite 306
Fluid capacities ......................... 294 Foglamps .....................................45 Four -Wheel Drive vehicles ....... 190 description .............................. 194 driving off road ....................... 196 electronic shift ................190, 194 indicator light .........................191 lever operated shift ...............[...]
-
Seite 307
K Keyless entry system ................. 92 Keys positions of the ignition .........172 L Lamps autolamp system ....................... 44 daytime running light ...............45 fog lamps ...................................45 headlamps .................................44 headlamps, flash to pass ..........46 instrument panel, dimming ..... 46 inte[...]
-
Seite 308
R Radio ................................21, 23, 28 Relays ........................................ 211 Remote entry system ................. 88 illuminated entry ...................... 91 locking/unlocking doors ........... 85 Reverse sensing system ........... 188 Roadside assistance .................. 208 S Safety Belt Maintenance .......... 112 [...]
-
Seite 309
T railer Brake Controller -Integrated ................ 164 T ransfer case fluid checking ......................... 290 T ransmission automatic operation .........60, 182 brake-shift interlock (BSI) .... 182 fluid, checking and adding (automatic) ............................. 286 fluid, checking and adding (manual) ................................. [...]
-
Seite 310
310[...]
-
Seite 311
311[...]