Garmin 276C Bedienungsanleitung

GPSMAP ® 276C chartplotting receiver owner’ s manual[...]

© Copyright 2004, 2005 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151 st Street, Olathe, Kansas 66062, U.S.A. T el. 913/397.8200 or 800/800.1020 Fax 913/397.8282 Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey , SO51 9DL, U.K. T el. 44/0870.8501241 Fax 44/0870.8501251 Garmin Corporation N[...]

I NTRODUCTION Thank you for choosing the Garmin ® GPSMAP ® 276C, which utilizes the proven performance of Garmin GPS and full-featured mapping to create an unsurpassed portable marine navigation chartplotter and automobile navigation device. T ake a moment to compare the contents of this package with the packing list on the outside of the box; if[...]

T able of Contents Introduction ...........................................................................i Caring for the GPSMAP 276C ................................................ iv W arning .................................................................................... v Caution ..........................................................[...]

Sonar T ab ............................................................................... 70 Alarms T ab ............................................................................. 71 Calendar T ab .......................................................................... 73 Celestial T ab ........................................................[...]

Caring for the GPSMAP 276C The GPSMAP 276C case is constructed of high quality materials and does not require user maintenance except cleaning. Cleaning the Case Clean the unit’ s outer casing (except for the screen) using a cloth dampened with a mild detergent solution and then wipe dry . A void chemical cleaners and solvents that may damage pla[...]

Failure to avoid the following potentially hazardous situations could result in an accident or collision resulting in death or serious injury . When installing the GPSMAP 276C in a vehicle, place the unit securely so that it does not interfere with vehicle operating controls or obstruct the driver ’ s view of the road (see diagram). Do not mount [...]

Failure to avoid the following potentially hazardous situations may result in injury or property damage. The GPSMAP 276C is designed to provide you with route suggestions. It does not reflect road closures or road conditions, traffic congestion, weather conditions, or other factors that may affect safety or timing while driving. Use the GPSMAP 27[...]

G ETTING S T ARTED Unit Overview The GPSMAP 276C is an all-in-one, versatile color chartplotter and automobile navigator—perfect for land or water . This portable GPS navigator features a 256-color TFT display that is easy to read in bright sun, a built-in basemap, and auto routing to provide you with automatically generated turn-by-turn directio[...]

Charging the GPSMAP 276C Before using the unit, you might need to charge the battery in the GPSMAP 276C. Plug the unit into an external power source to charge. Y ou can use the unit while it is char ging. T o charge the unit’s battery: 1. Lift the rubber weather cap to expose the power connector on the back of the unit. See the image on page 1 fo[...]

T urning On the GPSMAP 276C The first time you turn on your new GPSMAP 276C, the GPS receiver must collect satellite data and establish its current location. T o ensure proper initialization, the GPSMAP 276C is shipped from the factory in AutoLocate mode, which allows the receiver to “find itself” anywhere in the world. Before you turn on the[...]

Getting Satellite Signals After you turn on the GPSMAP 276C, the unit automatically begins searching for satellites. The GPS page appears while the unit is gathering satellite signals and acquiring a fix, which should take only a few minutes. While the GPSMAP 276C is getting satellite signals, the GPS page shows the status as “Acquiring Satellit[...]

GPS Status Receiver status field Sky view Signal strength bars Power source indicator The progress of satellite acquisition is shown in three stages: • No signal strength bars —the receiver is looking for the satellites indicated. • White signal strength bars —the receiver has found the satellite and is collecting data. • Green signal st[...]

GPS Options Press MENU twice to open the Main Menu. Use the ROCKER to highlight the GPS tab. Press MENU to open the Options menu. GPS T ab Options Menu Start/Stop Simulator —starts and stops Simulator Mode, which is helpful when learning how to use your unit. Enable/Disable W AAS —enables or disables W AAS capability . See page 108 of the “Ap[...]

IN and OUT Keys • Press to adjust map scale to show a larger area with less detail (zoom out) or a smaller area with more detail (zoom in). P AGE Key • Press to cycle through the main pages in sequence and exit a submenu page. • Press and hold to switch between Marine and Automotive modes. QUIT Key • Press to cycle through the main pages in[...]

Using the GPSMAP 276C This section explains how to enter and select information with the GPSMAP 276C. Understanding T erms The GPSMAP 276C’ s advanced keypad system is designed to allow quick, convenient selection of navigation options and data entry . As you progress through this owner ’ s manual, you are directed to press a specific key or h[...]

Selecting Options and Entering Data T o enter data and select options, use the ROCKER to highlight, select, or choose an item in a list or a field on the screen. Use the ENTER key and the ROCKER to select options, enter names and numbers in data fields, and activate your selections. T o select and activate an option: 1. From any page, press MENU [...]

Entering data TIP: T o clear the entir e data field, highlight the left-most character field and pr ess left on the ROCKER again. 3. Press ENTER . Not all fields are programmable. When you are on a page with fields that are not selectable, the highlight skips over them. Restoring Default Settings Y ou can restore factory defaults for the follow[...]

Simulator Mode T o help you get to know your GPSMAP 276C, you can use the unit in Simulator Mode. Simulator Mode is helpful for practicing with the unit indoors or when no satellite signals are available. All waypoints and routes created in Simulator Mode are retained in memory for future use. W ARNING: Do not attempt to navigate using Simulator Mo[...]

B ASIC O PERA TION I N M ARINE M ODE This section explains some of the more common operations you will perform with your GPSMAP 276C, such as navigating to a destination. T o switch usage modes: 1. Press and hold the P AGE key . The Usage Mode menu appears. 2. Use the ROCKER to select either Automotive or Marine , and press ENTER . Marine Mode Page[...]

Navigating in Marine Mode There are several ways to begin navigating to a point: • Select a point on the map, and press NA V . • Press NA V to activate a new route using the Find Menu or activate a saved route or track. • Press the FIND key to search for a particular item and create a route to it. Marine Mode and Automotive Mode are similar .[...]

T o go to a highlighted map item: 1. Use ROCKER to highlight the item to which you want to navigate on the Map Page. 2. Press NA V . Go T o <point name> appears in the list of options and is automatically highlighted. If you selected an area of the map that is not a map feature, Go T o MAP Point is listed. Select Go T o <point name> or [...]

T o search for an item and route to it: 1. Press FIND to open the Find menu. 2. Using the ROCKER , highlight a category , such as Cities , and press ENTER . 3. Press ENTER and use the ROCKER to begin entering the letters contained in the item name. The list begins to sort by the items that contain the letters you are entering. Press ENTER when fin[...]

Finding an Item Use the Find menu to easily search the stored waypoints and points of interest. T o open the Find menu, press the FIND key . The Find menu is comprised of several default categories: W aypoints, Cities, Exits, T ransportation, and T ide Stations. Additional categories appear depending on the optional BlueChart or MapSource data card[...]

T o find an item from another location: 1. From any page, press FIND . 2. Using the ROCKER , highlight a category from the list, and press ENTER . 3. Press MENU to open the options menu. Find From Options Menu 4. Highlight Near Other , and press ENTER . If you are actively following a route, you can also select one of the other options listed in t[...]

Viewing the Information Page Each item on the map and each item listed in the Find menu results list has an Information Page. T o view details about an item: 1. Highlight a point on the map or in the search results list, and press ENTER . An Information Page appears with details about the item in a tabbed format. Depending on the type of item, addi[...]

Creating and Using Routes Use the GPSMAP 276C to create and store up to 50 reversible routes, with up to 300 points each. Creating a Route Use the Route tab on the Main Menu to create routes. Y ou can create routes two ways. The first way is to select waypoints from the Find Menu, allowing you to see a list of the route points as you create the ro[...]

T o create a route graphically: 1. Press MENU twice to open the Main Menu. Use the ROCKER to highlight the Route tab. 2. Press MENU to display the Route options menu. Select New Route , and press ENTER . 3. Highlight the first blank slot in the Route List Page and press MENU . Use the ROCKER to highlight Edit on Map , and press ENTER . 4. Use the [...]

Editing a Route After you create a route, use the Route Review Page to edit, change the name, and review route points of a selected route. T o change the name of the route: 1. Press MENU twice to open the Main Menu. Highlight the Route tab. 2. Highlight the route you want to edit, and press ENTER . 3. With the Route Review Page open, highlight the [...]

T o add points to the route: 1. Press MENU twice to open the Main Menu. Use the ROCKER to select the Route tab. 2. Highlight a route, and press ENTER . 3. Press up or down on the ROCKER to highlight the spot in the route that you want to add the new point. (The new point is added before the highlighted route point), and press MENU . 4. Highlight In[...]

Y ou can enter information about your trip so the GPSMAP 276C can estimate information about your trip. T o plan your route: 1. Open the Route Review Page options menu. 2. Highlight Plan Route , and press ENTER . Entering Speed and Fuel Flow for trip planning 3. Enter the data for Speed and Fuel Flow . Y ou also can enter the date and time of your [...]

Creating and Using W aypoints W aypoints are locations or landmarks you record and store in your GPS. They are locations you might want to return to later , such as checkpoints on a route or significant ground features. Y ou can add waypoints to routes and even create a Go T o directly to the selected waypoint. Save your current location as a wayp[...]

Creating W aypoints Using the Map Y ou can quickly create a waypoint using the Map Page. When you pan the map and move the arrow over a map item, you see a highlighted description of that item. The GPSMAP 276C uses the map item text shown on the map as the default name and symbol for the new waypoint. T o create a new waypoint using the Map Page: 1[...]

Creating a W aypoint by Entering Coordinates Y ou can manually enter location coordinates to create a waypoint. This method is useful for creating a waypoint at a specific latitude/ longitude position from a chart. Y ou can manually change the location coordinates in the New W aypoint Page to create a new waypoint or use the Create W aypoint selec[...]

Reviewing a W aypoint After you create and store a waypoint, you can modify , review , rename, move, or delete it at any time using the W aypoint Review and W aypoint Edit Pages. These pages provide virtually the same information. T o access the Waypoint Review Page: 1. Use the ROCKER to highlight a waypoint on the Map Page. 2. Press ENTER to open [...]

Adding a W aypoint to a Route Append to Route adds the selected waypoint to the end of a route. This option appears when you are not navigating. When you are navigating to a destination, Add to Current Route appears. The selected waypoint is added to the current route before the route destination. T o add a waypoint to the end of the route: 1. Open[...]

Projecting a W aypoint Y ou can also create a new waypoint by projecting the distance and bearing from a specific location to a new location. T o create a new waypoint by projecting its location: 1. Create a waypoint using your favorite method (discussed in previous sections). The new waypoint is created with the next available waypoint number and[...]

Editing a W aypoint The User sub tab shows a master list of all waypoints currently stored in memory . From the User list, you can review , edit, rename, or delete individual waypoints, or delete all user waypoints. User Sub T ab The total number of stored and available waypoints appears at the bottom of the User sub tab, with the stored waypoints [...]

Organizing W aypoints into Categories Y ou can organize your waypoints into categories to help you manage and use your waypoints. For example, you can create a V acation category that stores all of the waypoints you will use for your upcoming vacation. When the vacation is over , you can delete all the waypoints in that category by pushing a few bu[...]

T o delete a category: 1. With the W aypoint Categories window open, highlight the category you want to delete, and press MENU . 2. Highlight Delete Category , and press ENTER . W aypoint Categories Options Menu 3. Press ENTER again to finish deleting the category . Deleting W aypoints Y ou can delete waypoints from the waypoint list in the Points[...]

3. When deleting by symbol, highlight the symbol of the waypoint you want to delete, and press ENTER . When deleting by category , select the category you want to delete from the list, and press ENTER . 4. Highlight OK , and press ENTER to confirm. Choose Cancel or press QUIT to exit without deleting the waypoint. T o delete waypoints by distance:[...]

T o turn proximity alarms on or off: 1. Press MENU twice to open the Main Menu. 2. Highlight the Points tab, and then highlight the Proximity sub tab. 3. Use the ROCKER to highlight the Proximity Alarm field, and press ENTER . 4. Select On or Off , and press ENTER . T o add a proximity waypoint: 1. From the Proximity sub tab, use the ROCKER to hig[...]

Managing Y our T racks The GPSMAP 276C draws an electronic breadcrumb trail or “track log” on the Map Page as you travel. The track log contains points along its path, including time, and location for each point. The track log starts recording as soon as the GPSMAP 276C gets a location fix. For the best results, clear the track log before you [...]

T o clear the track log: 1. Press MENU twice to open the Main Menu. 2. Highlight the T rack tab, and highlight the Active sub tab. 3. Highlight the Clear button, and press ENTER . A confirmation message appears. Clearing the track log 4. Highlight OK , and press ENTER . 5. Press QUIT to exit. T o save the entire track log: 1. Press MENU twice to o[...]

Saved T racks The Saved sub tab shows all of the saved tracks in your unit. Saved Sub T ab Press MENU to open the Saved tab options menu: Review on Map —shows the highlighted track on the Map Page. T racBack —navigates the track. Y ou can either navigate the track as it is saved, or you can navigate the track in reverse. Delete T rack —erases[...]

Navigating a Saved T rack Y ou can save your track log to use later as a T racBack, which reduces your track log into a route with up to 300 turns. When initiated, a T racBack route leads you back to the oldest stored track log point. It is a good idea to clear the existing track log before you start your current trip. Also, you must save an active[...]

Following a Marine Route After you activate a route, the GPSMAP 276C automatically starts guiding you to the destination using a variety of tools and pages. See Y our Route on the Map Page Y ou can track the progress of your route on the Map Page. Y our route is shown with a magenta line. For more information, see the “Map Page” section beginni[...]

See Y our Progress on the Active Route Page When you initiate a route in Marine Mode, the Active Route Page shows each point (waypoint or map item) of the active route, as well as the point name, course, distance, and several other fields of information. The active point is marked with an arrow icon. As you navigate a route, the list automatically[...]

M ARINE M ODE P AGES AND F EA TURES This section discusses the major pages in Marine Mode, such as the Map and Compass pages, and some additional marine features, including DSC and the Marine T imer . Map Page The GPSMAP 276C features a real-time moving map that can do much more than just plot your course. The Map Page shows map information (digita[...]

4. Select an option, and press ENTER . The options vary between the three usage modes and the page you are setting up. Selecting the page layout T o change a data field display: 1. Press P AGE to open the page you want to change. 2. Press MENU to open the options menu. 3. Highlight Change Data Fields , and press ENTER . 4. Highlight the data fiel[...]

Setting up the Map Page 4. Press up or down on the ROCKER to highlight a setting, and press ENTER . 5. Press P AGE or QUIT to exit. Additional Map Data Y ou can view the data currently loaded on your GPSMAP 276C unit and data card. T o review/change map information: 1. On the Map Page, press MENU . 2. Highlight Map Information , and press ENTER . T[...]

5. T o view detailed information about an individual map, highlight the map name, and press ENTER . Highlight OK , and press ENTER to exit the Map Information page. 6. T o select or deselect individual maps for display on the Map Page, highlight the box next to the map you want, and press ENTER to check or uncheck the Show box. Or Press MENU , sele[...]

• When the selected zoom range exceeds the resolution of the data in use, “overzoom” appears below the map scale. No additional data is available • When external data (such as MapSource data) is used, “map card” appears below the map scale. Using detailed maps loaded on the data card Panning the Map The panning arrow allows you to pan t[...]

T o view details about an on-screen point: 1. Use the ROCKER to move the arrow to a waypoint or map item. If there are several items grouped closely together , zoom in closer for a better view . When a waypoint or map item is selected, it is highlighted on- screen with the name and location shown at the top of the screen, along with the distance an[...]

Measuring Distance Y ou can measure the distance and bearing between two map items. T o measure the bearing/distance between two points: 1. On the Map Page, press MENU to open the options menu. 2. Highlight Measure Distance , and press ENTER . An on- screen arrow appears on the map display at your present location with ENT REF below it. 3. Move the[...]

If the arrow points up, you are going directly to the waypoint. If the arrow points any direction other than up, turn toward the arrow until it points up, and then continue in that direction. NOTE: Y ou must be moving for the compass to accurately update and show your heading. T urning On the Compass Page The Compass Page is on by default in Marine[...]

Y ou must change the Compass Page layout to use the Marine T imer . T o open the Marine Timer: 1. Press P AGE repeatedly until the Compass Page appears. 2. Press MENU . 3. Use the ROCKER to highlight Set Up Page Layout and press ENTER . 4. Highlight 2 Columns With T imer , and press ENTER . The Marine T imer appears in the lower right corner . T o [...]

Highway Page The Highway Page is available in both Marine Mode and Automotive Mode, though it is not shown by default in Automotive Mode. Press P AGE repeatedly to open the Highway Page. Highway Page When you are navigating, the Highway Page provides digital and graphic steering guidance to the destination. The right side of the Highway Page featur[...]

Highway Page Options Use the Highway Page options menu to define the data fields and select which waypoints and tracks appear on the screen. The data fields, located along the right side of the page, provide various types of useful data. Y ou can customize the layout to show additional data fields. T o display and select the Highway Page Option[...]

Active Route Page When you initiate a route in the GPSMAP 276C, the Active Route Page shows each point (waypoint or map item) of the active route, with the point name, Course, Distance, and several other fields of information. The current destination point, the active point, is marked with an arrow icon. As you navigate a route, the list automatic[...]

Position Data Page The Position Data Page shows important navigation data while navigating a route in Marine Mode. By default, the page shows a compass ribbon, your current latitude and longitude, the current date and time, your location in relation to a prominent nearby landmark such as a waypoint or city , and eight user -selectable data fields.[...]

B ASIC O PERA TION I N A UTOMOTIVE M ODE This section discusses some of the more common Automotive operations you will perform with your GPSMAP 276C in Automotive Mode. Please note that many common operations, such as marking a waypoint and creating a route, are performed the same way as in Marine Mode. See the Marine Mode sections for operations a[...]

Navigating in Automotive Mode When you initiate navigation in Automotive Mode, the GPSMAP 276C automatically generates a turn-by-turn route. In some instances, you may need to select the Follow Roads option to generate a turn-by-turn route. When you are actively navigating, you will see a magenta line that always runs from your current location to [...]

T o create a new route: 1. Press NA V to open the Navigate menu. 2. Highlight New Route , and press ENTER . 3. From the Find menu, highlight W aypoints , and press ENTER . (Y ou can also choose to go to other points, such as Cities or Exits from this list. The steps vary only slightly from those listed for waypoints.) 4. Select a waypoint from the [...]

Following a Saved Route Use the Navigate menu to follow a saved track or route. If you want to follow roads on your route, press MENU , and select Follow Roads on the Active Route Page. T o follow a saved route in Automotive Mode: 1. Press NA V to open the Navigate menu. 2. Highlight Navigate Route , and press ENTER . 3. Highlight the route you wan[...]

Editing Y our Route When you are navigating a route, you can edit that route. Y ou can add areas and roads to avoid as well as temporary detours to your current route. Y ou can also add stops along your trip, called V ia Points. While navigating, press NA V to open the Navigate menu. Entering Custom Avoids Custom avoids allows you to enter specifi[...]

Detour Distance 4. T o end the detour manually , press NA V again, and select Cancel Detour . Adding and Editing Stops (Via Points) Y ou can add V ia Points—points through which you would like to travel—to your route using the Edit V ias option. V ia Points are great for adding a stop at the gas station or bank to your route and are really help[...]

Following an Automotive Route The GPSMAP 276C guides you to your destination using many tools, such as the Map Page and Current Route Page. T rack Y our Progress with the Map Page Y ou can track the progress of your route on the Map Page. Y our route is shown with a magenta line. The next turn is shown in the top bar on the Map Page. Map Page showi[...]

A UTOMOTIVE M ODE P AGES AND F EA TURES This section discusses the major pages in Automotive Mode, such as the Map Page, as well as some additional features, such as Routes and Points. For information about pages and features not discussed here, see the “Marine Mode Pages and Features” section. Map Page See page 41 in the “Marine Mode Pages a[...]

Current Route Page Whenever you activate a route in the GPSMAP 276C in Automotive Mode, the Active Route Page shows each turn of the active route, with the distance to the turn, the street name, and estimated time to arrival and time of arrival. As you navigate a route, the turn list automatically updates to indicate the next turn at the top of the[...]

T rip Computer Page The T rip Computer Page shows important data while navigating a route in Automotive Mode. It indicates your current speed and other helpful data about your trip, such as average speed and moving time. T rip Computer Page Reset the T rip Computer before beginning a trip. If you make frequent stops, leave the GPSMAP 276C turned on[...]

M AIN M ENU The Main Menu on the GPSMAP 276C provides access to various waypoint, system, navigation and interface management, and setup menus. The Main Menu is accessible from any page by pressing the MENU key twice. Main Menu T o select a tab from the Main Menu: 1. From any page, press MENU twice to open the Main Menu. 2. Press up or down on the [...]

Route T ab Use the Route tab create and store up to 50 reversible routes, with up to 300 points each. See the “Creating and Using Routes” section beginning on page 19 for more information about routes. Main Menu—Route T ab Points T ab The Points tab contains two sub tabs, User and Proximity , which allow you to manage a large number of waypoi[...]

T rack T ab Use the T rack tab to specify whether or not to record a track log, define how it is recorded, or save the track log data for future use. The T rack tab is divided into two sub tabs: Active and Saved. For more information about tracks, see the “Managing Y our T racks” section beginning on page 35 . Main Menu—T rack T ab Active Su[...]

Understanding Distress Calls W ith your GPSMAP 276C properly connected to a VHF radio with DSC output, you can receive any DSC distress call within range. An alert message appears and a tone sounds when a distress call is received. The alarm only sounds on a distress call; position reports do not sound the alarm. Distress calls are broadcast to all[...]

DSC Call List The Ca ll L ist sh ows the 50 mos t re cen t c alls , e ven if the uni t i s le ft una tte nded . The Ca ll L ist on ly s how s th e m ost rec ent cal l f rom a ves sel . If a sec ond cal l is re ceiv ed, it rep lac es t he first ca ll in t he Call Lis t. Pres s M ENU to sor t th e l ist and de lete en trie s. DSC Call List DSC Log W[...]

DSC Directory list DSC Directory entries. Press ENTER to open the entry review page. Blank entry . Press ENTER to add a DSC Directory entry . T o add a new DSC Directory entry: 1. Open the DSC Directory on the Main Menu. 2. Use the ROCKER to highlight the first blank space in the directory list, and press ENTER . Or Press MENU , highlight New Item[...]

Setting Up DSC Use the Setup sub tab to turn DSC on and off. If you have more than one chartplotter and only want DSC to display on another chartplotter , turn DSC off on this unit. This Setup sub tab also allows you to simulate Distress Calls and Position Reports while the unit is in Simulator Mode (see page 1 1 ). Simulating calls is helpful for [...]

Alarms T ab Use the Alarms tab to define alarm settings. When an alarm goes of f, the alarm message appears on the display and the unit emits five (5) beeps. When you set an alarm to be persistent, the alarm message appears on the display and the unit beeps until you press ENTER to acknowledge the alarm. Main Menu—Alarms tab T o set an alarm: 1[...]

Off Course —sets an alarm to sound when off your desired course. Select On , then enter a distance. Anchor Drag —sets an alarm to sound when you exceed a specified drift distance. Select On , and then enter a distance. System Alarms The System sub tab contains the following alarms: Clock —sets an alarm based on the unit’ s clock. Select On[...]

Calendar T ab Use the Calendar tab to plan trips, view sun and moon, and hunting and fishing information for the day . Calendar T ab in Day View Highlight an arrow , and press ENTER to change the date in the view . Sunrise and set times for the current location and date. List of points and routes added to this date. Calendar Options The options me[...]

Celestial T ab The Celestial tab shows tide information, sun and moon information, and hunting and fishing information. Y ou can view this data for your current location, a location from the map, or a waypoint location. Also, you can select a different date and time, or use the current data. Main Menu—Celestial T ab T o access the Celestial tab:[...]

T o view a tide chart for a different tide station: 1. From the Tide sub tab, highlight the At field, and press ENTER . The Find menu opens showing the tide stations. 2. Press MENU , and select Near Current Location , Near Current Route , Near Other (select another location using the map), or Near Destination . The list is updated with your search[...]

T o view sun and moon information for a different date: 1. Use the ROCKER to highlight the Date field, and press ENTER . 2. Use the ROCKER to change the digits of the date to the date you want. Y ou can also use the IN and OUT keys to view information for another date. Press and hold IN or OUT to scroll quickly through dates. 3. Press ENTER when ?[...]

Hunt & Fish Sub T ab T o view hunt and fish information for a different date: 1. Highlight the Date field, and press ENTER . 2. Use the ROCKER to change the digits of the date to the date you want. Y ou can also use the zoom IN and OUT keys to view information for another date. Press and hold IN or OUT to scroll quickly through dates. 3. Pres[...]

Message T ab The Message tab shows a list of messages generated by the GPSMAP 276C. Use the ROCKER to scroll through the entire list of messages on the Log sub tab. Use the Log Filter sub tab to show only the message types that you want to view . Main Menu—Message T ab T o view messages: 1. Press MENU twice to open the Main Menu. 2. Highlight the[...]

Display T ab Use the Display tab on the Main Menu to set display features, such as which pages to show in the main page sequence and how long the backlight stays on. T o access the Display tab: 1. Press MENU twice to open the Main Menu. 2. Use the ROCKER to highlight the Display tab. Main Menu—Display T ab The Display tab contains the following o[...]

Sound T ab Use the Sound tab to customize the sounds made by the unit. T o access the Sound tab: 1. Press MENU twice to open the Main Menu. 2. Use the ROCKER to highlight the Sound tab. Main Menu—Sound T ab Beeper —sets the beeper to chime during keypresses and alarms ( Key and Alarm ) or on Alarms Only . Attention T one —turns on and off the[...]

Usage Mode —sets the unit to operate in Marine (default) or Automotive Mode. Speed Filter —allows the unit to average speed readings. Choose from Off , Auto (automatically controls filtering), or On (allows you to enter a value in seconds). T ext Language —sets the unit’ s on-screen language. W AAS —allows you to enable or disable W AAS.[...]

Calculation Method —sets how the unit searches for the route. • Quickest Calculation —calculates the route the quickest, but it might not produce the best route. • Quick Calculation —takes a bit more time to calculate but generates a better quality route. • Better Route —generates an even better quality route but uses a longer calcula[...]

Timers Sub T ab Use the T imers sub tab to set timers and view information about how long the unit has been on. T o access the Timers sub tab 1. Press MENU twice to open the Main Menu. 2. Use the ROCKER to select the Setup tab, and then select the Timers sub tab. Timers Sub T ab User —allows you to set the timer to Count Up or Count Down . Y ou c[...]

Units Sub T ab Use the Units sub tab to customize measurement units. T o access the Units sub tab 1. Press MENU twice to open the Main Menu. 2. Use the ROCKER to select the Setup tab, and then select the Units sub tab. Units Sub T ab Distance and Speed— select the unit to show your speed and distance traveled. Direction Display —select the unit[...]

The default setting is WGS 84. The unit automatically selects the best datum depending on your chosen location format. W ARNING: Selecting the wr ong map datum can result in substantial position err ors. When in doubt, use the default WGS 84 datum for best overall performance. Selecting a Different Heading Reference Y ou can s elect f rom Aut o Mag[...]

3. T o show the welcome message when you turn on your GPSMAP 276C, highlight the Show at Power-up check box, and press ENTER to select it. T o hide the welcome information at start-up, clear the check mark. Com 1 and Com 2 Sub T abs Use the Com 1 and Com 2 sub tabs to change the data format and control the input/output format used when connecting y[...]

• T ext Out —allows the unit to output simple text data that includes, data, time, location, and velocity . The Baud can be set to 1200, 2400, 4800, or 9600. • None —provides no interfacing capabilities. If you select GARMIN DGPS or R TCM In/NMEA Out format, you can control a differential beacon receiver directly from your GPSMAP 276C using[...]

When the unit is receiving a DGPS signal, the Signal to Noise Ratio) (SNR) and Distance fields show data. The SNR range is 0 dB to 30 dB, with 30 being the best. The Distance field may or may not show data, depending on the signal being broadcast from the DGPS site. The DGPS beacon transmitters are operated by the United States Coast Guard (or si[...]

S ETTING U P AND U SING S ONAR This section covers the additional sonar options for the GPSMAP 276C when used in conjunction with a GSD 20 Sounder Module. Read the GSD 20 Sounder Module Installation Instructions to properly install the sounder module. When you turn on your GPSMAP 276C, the Sounder Module automatically turns on. NOTE: Y ou MUST have[...]

Using the Sonar Page When combined with a GSD 20 Sounder Module, your GPSMAP 276C becomes a powerful fishfinder/flasher with the Sonar Page. If a GSD 20 is attached, but the unit does not detect a transducer , a “Sonar T urned Off” message appears across the Sonar Page. The Sonar Page appears only if a GSD 20 has ever been attached or when t[...]

T o select an adjustment option: Use one of the following methods to select an adjustment option: • Press the ROCKER right or left to scroll through the adjustment options. When the adjustment option you want appears, press ENTER . • Press MENU , highlight Adjustments , and press ENTER . Use the ROCKER to highlight the adjustment, and press ENT[...]

• Btm (Bottom) Split —shows two reduced pictures, the right at the original depth scale and the left showing sonar returns from the bottom up. All target depths read as a distance from the bottom. • Btm (Bottom) Lock —shows returns from the bottom up on the full screen. TIP: Quickly zoom in and out of the Sonar display by pr essing the IN a[...]

Using the Pointer on the Sonar Page Y ou can show the pointer (arrow) to reference sonar items and mark underwater waypoints. This makes it easier to find and use an object such as a stump for a future fishing location. When using this feature, the Sonar Page pauses. The depth continues to update while the display is paused, but the unit does not[...]

Depth Number —select how efficient the digital depth update rate is. Fast Update updates quicker and is recommended for low-noise water deeper than 50 feet. Auto is best for shallow water or high- noise areas, has a slower screen update, and is best used if you travel a wide variety of depths. If the unit is unable to track the bottom for any re[...]

Calibrating the W ater Speed 3. If the new speed is correct, highlight OK , and press ENTER . If you want to manually enter a calibration, press ENTER while the speed is highlighted, enter a new speed, and press ENTER again. If the boat is not moving fast enough or the speed sensor is not outputting a speed, “Boat Is Not Moving Fast Enough T o Ca[...]

Flasher —select On to display a graphic Flasher representation on the far right side of the sonar display . This graphic Flasher shows structure and bottom returns much the same as a true Flasher . Y ou might find this feature useful when using Fish Symbols. T emperature Graph —select On to display a temperature graph along the bottom of the S[...]

Changing the T emperature Display The graph will adjust and show the temperatures changes according to the T emperature Scale and T ime Duration settings. T emperature Scale —select a degree span from the list. Select Auto to have the unit automatically determine the best range, or select a span of 2, 4, 6, 8, or 10 degrees. Time Duration —set [...]

Generally speaking, if the only thing between the transducer and the bottom is water , the first strong return comes from the bottom directly below the transducer and sets the bottom level. W eaker secondary returns provide the detailed data. Stronger returns display in darker colors, with red being the strongest return. Understanding the Sonar Di[...]

The narrow cone angles (10°) associated with high frequencies (200 kHz) provide better bottom resolution and crisper detail, but cannot show a large coverage area for finding fish. The 10° cone angle provides a coverage width that is approximately 2/10 of the water depth. As shown in the drawing on the far right, the 10° cone angle produces a [...]

Whiteline The GSD 20 Sounder Module can help you determine whether the bottom is hard or soft. When the sonar sound waves are reflected back by the bottom, a hard bottom returns a stronger signal than a soft bottom. A thin whiteline indicates a softer bottom, while a thick whiteline indicates a harder bottom. Normally , a red line is used to show [...]

A PPENDIX Specifications Physical Specifications Size: 5.7" W x 3.2" H x 1.9" D (14.5 x 8.1 x 4.8 cm) W eight: 13.6 oz (0.39 kg) Display: 3.75" diagonal (9.5 cm) T ransflective, 256-color display with backlighting (480 x 320 pixels) Case: Fully gasketed, high-impact plastic alloy , waterproof to IEC 60529 IPX7 T emp. Range: 5[...]

Optional Accessories In addition to the standard accessories included with your GPSMAP 276C, several optional accessories are available to enhance the operation of the GPSMAP 276C. T o obtain replacement parts and optional accessories, contact your Garmin Dealer , Garmin Product Support in the U.S.A. at 800/800.1020, or Garmin Europe at 44/0870.850[...]

Installation Information This section of the Appendix provides information on connecting the GPSMAP 276C to auxiliary devices and removing the antenna. Connecting the Power/Data Cable The power/data cable connects the GPSMAP 276C to an 11–35 VDC system and provides interface capabilities for connecting external devices. The color code in the diag[...]

Connecting Y our GPSMAP 276C to a Computer Y ou can connect your GPSMAP 276C to your computer using the supplied USB cable to connect to a USB data port or the optional PC Interface cable to connect to a DB-9 serial communications port. NOTE : Fully install the supplied MapSour ce pr ogram, T rip & W aypoint Manager , on your computer befor e c[...]

Using xImage for Customized W aypoint Icons Use xImage to exchange images between your PC and your GPSMAP 276C. Y ou can download and save screenshots of any screen shown on your unit. xImage also allows you to download customizable splash screens and waypoint symbols from compatible GPS units, customize them (if you have an image editing program o[...]

Interfacing The following formats are supported for connection of external devices: GARMIN proprietary Differential GPS (DGPS), NMEA 0180, 0182, 0183 (versions 1.5, 2.0, 2.3, 3.01), ASCII T ext Output, and R TCM SC-104 input (version 2.0). The following are the Approved Sentences for NMEA 0183, version 3.01 output: GPRMC, GPGGA, GPGSA, GPGSV , GPGL[...]

Learning About GPS The Global Positioning System (GPS) is a satellite-based navigation system made up of a network of 24 satellites placed into orbit by the United States Department of Defense. GPS was originally intended for military applications, but in the 1980s, the government made the system available for civilian use. GPS works in any weather[...]

• Check Beacon W iring —the DGPS setting is enabled in the Interface sub tab on the Main Menu—Setup tab but no DGPS device is detected. • No Beacon Signal —DGPS receiver is attached, but not transmitting R TCM data to GPS. • T uning Beacon —the receiver is tuning manually to a DGPS frequency . • Using Differential —the unit is rec[...]

LORAN TD Setup LORAN C is a radio navigation aid operated and maintained in the United States by the United States Coast Guard. The name LORAN is an acronym for “LOng RAnge Navigation.” The LORAN system covers the entire United States and the United States Coastal Confluence Zone. From the perspective of a mariner , the system is used for ocea[...]

T o set up Loran TD from the Main Menu: 1. Press MENU twice to open the Main Menu. 2. Use the ROCKER to highlight the Setup tab, and then highlight the Location sub tab. 3. Using the ROCKER , highlight the Location Format field and press ENTER . Location Sub T ab 4. Highlight Loran TD , and press ENTER . 5. Highlight the Setup button located on th[...]

Map Datums and Location Formats Map Datums are based on a mathematical model of the Earth. What Are a Map Datums? A datum is a mathematical model of the Earth that approximates the shape of the Earth and enables calculations to be carried out in a consistent and accurate manner . The datum is physically represented by a framework of ground monument[...]

Digital Selective Calling (DSC) DSC uses marine VHF radio GPS technologies to transmit and receive location information. DSC is used by mariners to assist them in two major areas: Distress Calls and Position Reporting. A non-emergency DSC Position Report allows mariners to exchange and display their positions. When you receive a DSC position, you c[...]

How Are MMSI Assignments Obtained? Non-commercial users, such as recreational users, who remain in United States waters and only carry VHF , EPIRB (Emergency Position Indicating Radio Beacons), and Radar are not required to have a FCC ship station license. The FCC and Coast Guard have authorized some second and third-party vendors to assign MMSI nu[...]

Messages Accuracy Alarm —the GPS accuracy has fallen outside of user-set value. Alarm Clock —The alarm clock has sounded. Antenna Shorted to Ground —the external GPS antenna has an electrical connection problem. Contact Garmin Product Support. Approaching T urn —you are nearing a turn in a route. Arriving at Destination —you are nearing y[...]

No Roads Near Starting Point —the start location for the road route you tried to calculate is not near any roads. Select a different start location. No DGPS Position —no differential connection data is available, or not enough data is available to calculate a DGPS position. No T ide Stations for that Area —no tide stations within 100 miles of[...]

Data Field Options The following list provides a brief description of each data field option. Some of these options are supported only by devices interfaced to your GPSMAP 276C. Accuracy —the current accuracy of your GPS determined location. Battery T imer —the time remaining on the battery before it is fully discharged. Bearing —the compass[...]

Speed —your current vehicle speed can be measured in miles per hour , kilometers per hour , or knots. Steer —see Course to Steer . Sunrise —the time at which the sun rises on this day . Sunset —the time at which the sun sets on this day . Time —the current time and date. It can be shown in 12-hour or 24-hour format in local time or univer[...]

Software License Agreement BY USING THE GPSMAP 276C, YOU AGREE T O BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTW ARE LICENSE AGREEMENT . PLEASE READ THIS AGREEMENT CAREFULL Y . Garmin grants you a limited license to use the software embedded in this device (the “Software”) in binary executable form in the normal operation of the p[...]

Limited W arranty This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. W ithin this period, Garmin will at its sole option repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor , provid[...]

FCC Compliance The GPSMAP 276C complies with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE. These limits are designed to provide more reasonable protection against harmful interference in a residential installation, and are more stringent than “outdoor” requirements. Operation of this device is subjec[...]

I NDEX A Accessories 102 Accuracy Alarm 72 Acquiring Satellites 5 Active Route Page 40, 52, 54 Active T rack T ab 35, 38 AC Outlet 2 Add to Route 19, 22, 24, 28, 59 Advanced NMEA Output Setup 88 Alarms 80 DSC 67, 70 navigation 71 persistent 71 proximity 34 sonar 72 system 72 Alarms T ab 71–72 Alerts. See Alarms Anchor Drag Alarm 72 Antenna 1, 3, [...]

Distance and Speed 84 Distress Calls 66, 67–70, 1 12, 1 13 Drift 72 DSC 66–70, 1 12 E Edit route 21, 22, 58 waypoints 30 Editing a W aypoint 30 Emergency 1 12 Entering Data 9 Erase T rack Log 36 External Power Source 4 External V oltage Alarm 72 F Faster T ime 81 FCC 1 12, 1 13, 120 Field 8 Find 16 from 16 from a different location 16, 17 menu [...]

Marking a W aypoint 9, 24–26, 29 underwater 93 MayDay 69, 1 13 Measuring Distance 47 Messages 1 14, 1 16 Message T ab 78 Mils 84 MMSI 66, 1 12, 1 13 MOB 13, 15 Modes 12, 54 Month V iew 73 Moon Information 75 N NA V/MOB 15 Navigate route 13, 20 track 13, 15, 38 Navigation resuming 57 stopping 57 Navigation Alarms 71 Near current route 17, 18 desti[...]

T ime sub tab 83 Units sub tab 84 W elcome sub tab 85 Set an Alarm 71 Set Date 83 Set Fuel Flow 23 Set Speed 23 Shallow W ater Alarm 72 Shorter Distance 81 Signal Strength 5 Simulator Mode 1 1 new location 1 1 starting 1 1 Software License Agreement 11 8 Sonar 89, 90–92 adjusting 90–92 alarms 72 on the map page 89 setting up 93, 95 understandin[...]

[...]

For the latest fr ee software updates (excluding map data) throughout the life of your Garmin products , visit the Garmin W eb site at www .garmin.com. © Copyright 2004, 2005 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151 st Street, Olathe, Kansas 66062, U.S.A. Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Indus[...]