Deutsch dropdown-ico

Generac Power Systems 005028-0 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Generac Power Systems 005028-0 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Generac Power Systems 005028-0, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Generac Power Systems 005028-0 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Generac Power Systems 005028-0. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Generac Power Systems 005028-0 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Generac Power Systems 005028-0
- Den Namen des Produzenten und das Produktionsjahr des Geräts Generac Power Systems 005028-0
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Generac Power Systems 005028-0
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Generac Power Systems 005028-0 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Generac Power Systems 005028-0 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Generac Power Systems finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Generac Power Systems 005028-0 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Generac Power Systems 005028-0, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Generac Power Systems 005028-0 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    Owner’ s Man ual ONL Y QUALIFIED ELECTRICIANS OR CONTRACTORS SHOULD A TTEMPT INST ALLA TION!! This manual should remain with the unit. Liquid-cooled, Prepac ka ged Standb y Generator s Model Number 005030-0 (15kW) 005028-0 (20kW) 005031-0 (25kW)[...]

  • Seite 2

    I NTRODUCTION Thank you for purchasing this model of the QuietSource™ standby generator series. Every effort was expended to make sure that the information and instructions in this manual are both accurate and current at the time the manual was writ- ten. However , the manufacturer reserves the right to change, alter or otherwise improve this pro[...]

  • Seite 3

    T able of Contents Liquid-cooled 1 5, 20 and 2 5 kW Generators 1 INTRODUCTION ................................................ IFC Read this Manual Thoroughly ......................................IFC Operation and Maintenance ........................................IFC How to Obtain Service ................................................IFC Autho[...]

  • Seite 4

    2 Study these SAFETY RULES carefully before installing, operating or servicing this equipment. Become familiar with this Owner’s Manual and with the unit. The gen- erator can operate safely , efficiently and reliably only if it is properly installed, operated and maintained. Many accidents are caused by failing to follow simple and fun- damental [...]

  • Seite 5

    3 ELE CTR ICAL HA Z AR DS • All generators covered by this manual produce dangerous electrical voltages and can cause fatal electrical shock. Utility power delivers extremely high and dangerous volt- ages to the transfer switch as well as the standby generator . A void contact with bare wires, terminals, connections, etc., on the generator as wel[...]

  • Seite 6

    4 1.1 GEN ER A T OR This equipment is a liquid- cooled, engine - driven gen- erator set. The generator is designed to supply elec- trical power that operates critical electrical loads during utility power failure. The unit has been facto- ry-installed in a weather resistant, all metal enclosure and is intended for outdoor installation only . Use th[...]

  • Seite 7

    5 Figure 1.1 - Generator AC Connection System 1.6 MAI N CI RCU IT B R EAKER The generator’s main circuit breaker is included with the unit as shipped from the factory . The breaker for each unit is described in Figure 1.2. 1.7 GEN ER A T OR F U EL SY S TEM This unit has been factory tested and adjusted using a natural gas fuel system. If propane [...]

  • Seite 8

    6 Figure 1.5- High Coolant T emperature Switch 1.8.3 L O W C OOL ANT LEVEL SWIT CH Should engine coolant level drop below the level of the high coolant temperature switch, it is possible for the engine to overheat without automatic shutdown. T o prevent such overheating without automatic shut down, the engine has a low coolant level sensor . If the[...]

  • Seite 9

    1.1 1 SP ECIF ICA TIONS 1.1 1.1 ENGIN E Make ......................................................................................F ord Displacement ............................................153 inches 3 (2.5 liters) Cylinder Arrangement ......................................................4, in-line V alve Arr angement ........................[...]

  • Seite 10

    8 2. Remove the carburetor fuel hose from the outlet port (P ort 1) of the demand regulator (F igure 1.8). 3. Remove the brass hose fitting from the outlet port (P ort 1) of the demand regulator . 4. Remove pipe plug from P ort 2. 5. Install brass hose fitting into P ort 2. 6. Install pipe plug into P ort 1. 7. Connect carburetor gas hose to brass [...]

  • Seite 11

    9 2.1 S T AN DB Y GEN ER A T OR I NS T ALL A TION Connecting this generator to an electrical sys- tem normally supplied by an electric utility shall be by means of a transfer switch, so as to isolate the electric system from the utility distri- bution system when the generator is operating. Failure to isolate the electric system by these means will[...]

  • Seite 12

    10 2.4 B ASIC S T AN DBY ELE CTRIC SYST E M Figure 2.1 shows a schematic diagram of a basic standby electric system. Both the UTILITY power supply and the ST ANDBY GENERA TOR output are connected to an approved transfer switch. The trans- fer switch is required by electrical code and serves the following functions: • P ermits the LOAD circuits to[...]

  • Seite 13

    11 2.8 GEN ER A T OR AC NEUTR AL CO N N EC T I O N S The manufacturer uses an UNGROUNDED AC neu- tral. Grounding is recommended only at the main service entrance. If the neutral wire is grounded and one of the phase loads becomes grounded, the exces- sive current opens the load circuit breaker or col- lapses the generator field. The actual result d[...]

  • Seite 14

    12 2.1 0 ENGI N EER ED TR ANSF ER SWIT CH (2-WI R E S T ART G T S MODE) When required, the pre -packaged standby generator can be installed with an engineered W T ype transfer switch which controls utility voltage sensing, weekly exercising and load transferring . When P osition 2 of the eight -position DIP switch, which is located on the generator[...]

  • Seite 15

    13 Transfer Switch terminals N1 and N2 (also called Utility 1 and Utility 2) are the input utility AC power connections to the Transfer Switch. T ransfer Switch terminals T1 and T2 (also called Load 1 and Load 2) are the transfer switch AC output power terminals that go to the load circuit distribution panel. Transfer Switch terminals E1 and E2 are[...]

  • Seite 16

    14 The recommended battery is Group 26, 12VDC, 550 CCA/75 AH minimum. All batteries must be at 100 percent state - of- charge before they are installed on the generator . When using maintenance -free batteries, it is not nec- essary to check the specific gravity or electrolyte level. Have these procedures performed at the intervals specified in Sec[...]

  • Seite 17

    15 Section 3 - Operation Liquid-cooled 1 5, 20 and 2 5 kW Generators 3.1 C ONTROL CONS OLE C OM PON ENTS The components of a home standby generator control console (Figure 3.1) are as follows: Figure 3.1 - Generator Control Console 3.1.1 AUT O/OF F/MANUAL SWIT CH Use this three -position switch as follows: • Set the switch to A UTO for fully auto[...]

  • Seite 18

    16 3.3 ENGI N E G OVERNOR GAI N ADJ US TM ENTS Engine speed governing is also controlled by the engine control board. The engine governor has been set by the factory during final testing of the generator and should not be adjusted. If, however , adjustments are necessary , the following procedure should be followed (Figure 3.2 and Section 3.7): 1. [...]

  • Seite 19

    17 6. Reduce load to 3/4, 1/2, 1/4 and no load. Decrease the stability pot if there is instability at any load point. 7. Adjust differential pot to make the recovery to load changes even faster and minimize load change undershoot and overshoot. If it is set too high, it may introduce oscillations at some load. It can be set to zero (full CCW) if a [...]

  • Seite 20

    18 3.7 C ONTROL BO AR D DI P SWIT CH S E TTIN G S Located on the control board is an eight position DIP switch (see Figure 3.2). The eight different switches, are used to configure the control board for the spe- cific engine and governor being used and are pre - set at the factory . If the DIP switch settings are not set corr ectly , the generator [...]

  • Seite 21

    19 7. T urn the voltage regulator’s VOL T AGE ADJUST pot to obtain a line -to -line voltage of: A. 240 V AC if the generator has been configured for 60 Hertz operation. B. 200 V AC if the generator has been configured for 50 Hertz operation. 8. If the RED REGULA TOR LED is flashing, adjust the ST ABILITY pot in either direction until the flashing[...]

  • Seite 22

    20 3. Install a new lower intake manifold gasket. 4. P osition the lower intake manifold to the cylinder head. 5. Install retaining bolts/studs finger tight. 6. Tighten all bolts/studs to specifications in the tightening sequence shown: • F irst pass = 7=10 N-m (5-7 lb -ft). • F inal pass = 26-38 N-m (19-28 lb -ft). 4.4 CYLI N DER H EAD P ROCED[...]

  • Seite 23

    21 4 .7 .2 B A TT E R Y FL UID Check battery electrolyte fluid based on the Maintenance Schedule. Fluid should cover separa- tors in all battery cells. If fluid level is low , add dis- tilled water to cover tops of separators. DO NOT USE T AP W A TER IN BA TTERY . 4.7 .3 ENGI NE COOLANT Check coolant level in coolant recovery bottle. See Specificat[...]

  • Seite 24

    22 5. Apply light coating of new engine oil to seal of new oil filter . Install FIL TER and tighten by hand only . DO NOT OVER TIGHTEN . 6. Remove OIL FILL CAP . Add recommended oil (see SPECIFICA TIONS). DO NOT FILL ABOVE THE DIPSTICK “FULL ” MARK. Crankcase oil capacity is 4.0 U .S. quarts (3.8 liters). After refilling the crankcase with oil,[...]

  • Seite 25

    23 4.9.3 BA TTER Y MAI NTENANCE The battery should be inspected per Section 4.7, Scheduled Maintenance. The following procedure should be followed for inspection: 1. Inspect the battery posts and cables for tightness and corrosion. Tighten and clean as necessary . 2. Check the battery fluid level of unsealed batteries and, if necessary , fill with [...]

  • Seite 26

    24 Section 4 — Maintenance Liquid-cooled 1 5, 20 and 2 5 kW Generators 4.1 0 S CH EDU LED MAI NTENANCE The following is a recommended maintenance schedule for small standby and residential generator sets. The established intervals in the schedule are the maximum recommended when the unit is used in an average service application. They will need t[...]

  • Seite 27

    25 Section 4 — Maintenance Liquid-cooled 1 5, 20 and 2 5 kW Generators Maintenance Level 1 Level 2 Level 3 Level 4 T asks Recom- T ask Required T ask Required T ask T ask mended Comp . to be done Comp. to be done Comp . Required Comp . to be done (Date- 3 months/ (Date- Semi- (Date- to be done (Date- monthly Initials) Break-in Initials) annually [...]

  • Seite 28

    26 Section 4 — Maintenance Liquid-cooled 1 5, 20 and 2 5 kW Generators Maintenance Level 1 Level 2 Level 3 Level 4 T asks Recom- T ask Required T ask Required T ask T ask mended Comp . to be done Comp. to be done Comp . Required Comp . to be done (Date- 3 months/ (Date- Semi- (Date- to be done (Date- monthly Initials) Break-in Initials) annually [...]

  • Seite 29

    27 Section 5 — T roubleshooting Liquid-cooled 1 5, 20 and 2 5 kW Generators TROU B LE SHOO TI NG POI NTS P ROBLEM CAUSE CORR E CTION Engine won’t crank. 1. 15 amp fuse blo wn. 1. Replace fuse. 2. Loose or corroded or def ective 2. Tighten, clean or replace batter y cables . batter y cables as necessary . 3. Def ective starter contactor . 3. Rep[...]

  • Seite 30

    28 Section 6 — Notes Liquid-cooled 1 5, 20 and 2 5 kW Generators[...]

  • Seite 31

    29 Section 6 — Notes Liquid-cooled 1 5, 20 and 2 5 kW Generators[...]

  • Seite 32

    30 Section 7 - Electrical Data Liquid-cooled 1 5, 20 and 2 5 kW Generators Wiring Diagram — 2.5L Engine (1 5kW & 20kW units) —Drawing No. 0F2 1 83-B[...]

  • Seite 33

    31 Section 7 - Electrical Data Liquid-cooled 1 5, 20 and 2 5 kW Generators Wiring Diagram — 2.5L Engine (1 5kW & 20kW units) —Drawing No. 0F2 1 83-B[...]

  • Seite 34

    32 Section 7 - Electrical Data Liquid-cooled 1 5, 20 and 2 5 kW Generators Electrical Schematic — 2.5L Engine (15kW & 2 0kW units) —Drawing No. 0F21 84-B[...]

  • Seite 35

    33 Section 7 - Electrical Data Liquid-cooled 1 5, 20 and 2 5 kW Generators Electrical Schematic — 2.5L Engine (15kW & 2 0kW units) —Drawing No. 0F21 84-B[...]

  • Seite 36

    34 Section 7 - Electrical Data Liquid-cooled 1 5, 20 and 2 5 kW Generators Wiring Diagram — 2.5L Engine (25kW unit) —Drawing No. 0F1 286-B[...]

  • Seite 37

    35 Section 7 - Electrical Data Liquid-cooled 1 5, 20 and 2 5 kW Generators Wiring Diagram — 2.5L Engine (25kW unit) —Drawing No. 0F1 286-B[...]

  • Seite 38

    36 Section 7 - Electrical Data Liquid-cooled 1 5, 20 and 2 5 kW Generators Electrical Schematic — 2.5L (25kW unit) — Drawing No. 0F1 28 7 -B[...]

  • Seite 39

    37 Section 7 - Electrical Data Liquid-cooled 1 5, 20 and 2 5 kW Generators Electrical Schematic — 2.5L (25kW unit) — Drawing No. 0F1 28 7 -B[...]

  • Seite 40

    38 Section 8 - Exploded Views and P arts Lists Liquid-cooled 1 5, 20 and 2 5 kW Generators Mounting Base — Drawing No. 0F0 1 04-B[...]

  • Seite 41

    39 Section 8 - Exploded Views and P arts Lists Liquid-cooled 1 5, 20 and 2 5 kW Generators Mounting Base — Drawing No. 0F0 1 04-B ITEM P ART NO . QTY . DESCRIPTION 1 0F1705 1 SUPPORT BA TTER Y TRA Y 2 0E8834 1 HOLD DO WN BA TTER Y 3 0E9911 1 ASSEMBL Y BA TTER Y TRA Y 4 049813 1 NUT HEX M6 X 1.0 G8 YEL CHR 5 022097 4 W ASHER LOCK M6-1/4 6 026850 2[...]

  • Seite 42

    40 Section 8 - Exploded Views and P arts Lists Liquid-cooled 1 5, 20 and 2 5 kW Generators Enclosure — Drawing No. 0F1 645-H S TAT E S FOAM I S ON NEAR S IDE S TAT E S FOAM I S ON F AR S IDE 17 LA TCH DET AIL 3 0 3 1 3 1 3 2 3 4 3 2 3 45 1 8 39 38 40 4 7 47 DET AIL S EE LA TCH 9 "B" 2 9 46 11 1 8 17 4 3 8 1 3 1 1 8 S ECURE A S S HOWN. R[...]

  • Seite 43

    41 ITEM P ART NO . QTY . DESCRIPTION 1 0F0783 1 DUCT INT AKE MID AL 2.5L 2 0F0781 1 DUCT DISCHARGE RH AL 2.5L 3 0F0780 1 DUCT DISCHARGE LH AL 2.5L 4 0C2454 34 SCREW TH-FRM M6-1 X 16 N W A Z/JS 5 0F0779 1 SUPPORT RADIA T OR 2.5L AL 6 0E0072AB 1 AI INSULA TION SIDE REAR CORNER POST RH 7 0E0072A C 1 AI INSULA TION INT AKE DUCT TOP P ANEL 8 0E0072AD 1 [...]

  • Seite 44

    42 Section 8 - Exploded Views and P arts Lists Liquid-cooled 1 5, 20 and 2 5 kW Generators Control Panel (1 5kW and 20kW) — Drawing No. 0F22 67 -D[...]

  • Seite 45

    43 ITEM P ART NO . QTY . DESCRIPTION 1 0F0790 1 TOP , CONTROL P ANEL 2 0F0789 1 BACK & BO TT OM, CONTROL P ANEL 3 0F0791 1 P ANEL, FRONT 2.5L CONTR OL PNL 4 0E9704 1 ASSY PCB HSB CONTROLLER 2.5L 5 067680 1 ASSY V OL T A GE REGULA T OR 60HZ 6 0E6875A 2 RELA Y , 12VDC C FORM W/DIODE 7 0C3910 1 XFMR 240/16V 1V A&56V A 8 048468 1 CIRCT BRK 8 X [...]

  • Seite 46

    44 33 32 4 0 3 34 13 2 6 12 1 6 31 39 12 2 9 12 24 2 5 12 1 5 14 8 33 24 38 12 2 3 6 34 35 32 21 30 41 4 11 17 42 12 12 2 2 0 1 8 4 3 1 27 2 8 5 7 Section 8 - Exploded Views and P arts Lists Liquid-cooled 1 5, 20 and 2 5 kW Generators Control Panel (2 5kW) — Drawing No. 0E7 6 1 5-C[...]

  • Seite 47

    45 ITEM P ART NO . QTY . DESCRIPTION 1 0F0790 1 TOP , CONTROL P ANEL 2 0F0789 1 BACK & BO TT OM, CONTROL P ANEL 3 0F0791 1 P ANEL, FRONT 2.5L CONTR OL PNL 4 0E9704 1 ASSY PCB HSB CONTROLLER 2.5L 5 067680 1 ASSY V OL T A GE REGULA T OR 60HZ 6 0E6875A 2 RELA Y , 12VDC C FORM W/DIODE 7 0C3910 1 XFMR 240/16V 1V A&56V A 8 054450 1 CIRCT BRK 5.5 [...]

  • Seite 48

    8 15 66 16 14 19 41 30 20 27 60 20 30 29 28 59 39 5 2 19 38 39 20 40 2 25 4 17 13 15 19 FO R HARNE SS G R OU ND 5 3 22 17 68 15 19 10 38 22 3 1 0 HSG . 20 3 4 7 45 20 49 1 16 39 50 34 35 65 33 5 7 18 3 7 18 20 16 38 R ADIAT O R CAP 6 2 TO 58 39 S TEPPER MO T O R U NIT S O NLY 17 12 "A " 11 6 7 24 23 6 1 Section 8 - Exploded Views and P ar[...]

  • Seite 49

    ITEM P ART NO . QTY . DESCRIPTION 1 0E9909 REF ENGINE 2.5L FORD 2 0E9739 1 PULLEY , 2.5L FORD W A TER PUMP 3 049814 8 SCREW HHC M10-1.5 X 25 G8.8 4 0F0001 1 CLUTCH, COOLING F AN 2.5L FORD 5 0D3488B 1 SERPENTINE BEL T - 40.85" LENGTH 6 0A8584 1 SWITCH,OIL PRESSURE,10PSI,2POL 7 0E0561 1 ASSY W A TER LEVEL SENSOR C/E PL 8 0A6751 1 SW -TMP 245DEG [...]

  • Seite 50

    48 PO RT "OU T 1" 2 2 7 21 TO EN G INE 10 42 CO VER TO VALVE 12 13 28 1 8 20 33 3 1 3 2 17 3 4 26 6 38 30 16 25 24 18 4 29 15 9 5 27 6 4 C ARB U RET O R A SS Y. 0 E1028A ( I/N 19 ) CO NVER S I O N 35 41 "OU T 2" PO RT L .P. VAP O R 3 40 1 11 3 40 7 2 6 11 Section 8 - Exploded Views and P arts Lists Liquid-cooled 1 5, 20 and 2 5 [...]

  • Seite 51

    49 ITEM P ART NO . QTY . DESCRIPTION 1 0E8456 1 BRA CKET FUEL REGULA T OR 2 075580 1 FLANGE FUEL INLET 3 0E9967 1 ASSY FUEL REG 2.5L FRD N/G-L/P 4 039253 4 SCREW HHC M8-1.25 X 20 G8.8 5 022145 2 W ASHER FLA T 5/16 ZINC 6 022129 6 W ASHER LOCK M8-5/16 7 045771 2 NUT HEX M8-1.25 G8 YEL CHR 8 * 0F1570 1 BOD Y CARBURETOR ASSEMBL Y 9 0A6344 1 BARBED EL [...]

  • Seite 52

    50 3 LOC KTI G HT LOC KTI G HT 7 1 5 17 8 7 6 18 4 16 L EAD S 5 2 9 13* 21 19 20 14 10 11 12 30 1 3 1 Section 8 - Exploded Views and P arts Lists Liquid-cooled 1 5, 20 and 2 5 kW Generators Alternator — Drawing No. 0E8660-C[...]

  • Seite 53

    51 ITEM P ART NO . QTY . DESCRIPTION 1 0F1659A 1 R O T OR 390 15KW 1P DIRECT HSB (2.5L FORD) 0F1657A 1 R O T OR 390 20KW 1P DIRECT HSB (2.5L FORD) 0F1655A 1 R O T OR 390 25KW 1P DIRECT HSB (2.5L FORD) 0E5093A 1 R O T OR 390 30KW 1P DIRECT HSB (3.0L FORD & 2.5L FORD) 0E7413A 1 R O T OR 390 40KW 1P DIRECT HSB (3.9L CHR YSLER) 2 0F1660A 1 STR 390 [...]

  • Seite 54

    ITEM P ART NO . QTY . DESCRIPTION 1 0F2912 1 PIPE MUFFLER OUT 2 0F2869 1 PIPE EXHA UST 2.5L FORD 3 0F2823 1 MUFFLER 2.5L FORD 4 036434 2 BOL T U 5/16-18 X 2.09 5 036449 2 SADDLE 2 INCH 6 022129 6 W ASHER LOCK M8-5/16 7 022259 4 NUT HEX 5/16-18 STEEL 8 0E0170A 1 EXHAUST BLANKET 800MM 9 044149 1 GASKET EXHA UST RING 10 0E8816 1 EXHA UST FLANGE 2"[...]

  • Seite 55

    ITEM P ART NO . QTY . DESCRIPTION 1 098290 1 ASM MOT OR STEPPER 2 098941A 1 HOUSING GO VERNOR CONNECTOR 3 0F0454 REF HARN GOV 2.5L FORD 4 098942A 1 CO VER CONNECTOR HOUSING 5 098225 2 SCREW PFHST #2 X 5/8 6 043146 3 SCREW HHC M6-1.0 X 10 G8.8 7 022097 5 W ASHER LOCK M6-1/4 8 0E7358 REF SCREW PPPH HI-LO #4-24 X 3/8 9 098783 1 LEVER STEPPER MOT OR 10[...]

  • Seite 56

    54 ITEM P ART NO . QTY . DESCRIPTION 1 0E9769 REF SUPPORT RADIA T OR 2.5L FORD 0F0779 REF SUPPOR T RADIA TOR 2.5L AL 0E9769A REF SUPPOR T RADIA T OR 2.5L FORD ALM 2 0E9837 1 RADIA T OR 2.5L FORD 3 0F0123 1 VENTURI 16" F AN 2.5L FORD 4 0F0118 1 GU ARD F AN 2.5L FORD 5 099502 4 CLAMP HOSE #24 B1.06-2.00 6 0C2454 REF . SCREW THF M6-1 X 16 N W A Z[...]

  • Seite 57

    55 Section 9 — Installation Diagram Liquid-cooled 1 5, 20 and 2 5 kW Generators Installation Diagram — Drawing No. 0F1 022-A[...]

  • Seite 58

    56 CALI FOR N IA EM ISSION C ONTROL W AR R ANT Y S T A TEM ENT Y OU R W ARR ANT Y RIGHTS AND OB LIGA TIONS The California Air Resources Board (CARB) and Generac P ower Systems, Inc. (Generac) are pleased to explain the Emission Control System W arranty on your new engine. * In California, new utility , and lawn and garden equipment engines must be [...]

  • Seite 59

    57 EM IS SION CONTROL S Y STEM W AR R ANTY Emission Control System W arranty (ECS W arranty) for 1995 and later model year engines: (a) Applicability: This warranty shall apply to 1995 and later model year engines. The ECS W arranty P eriod shall begin on the date the new engine or equipment is purchased by/delivered to its original, end-use purcha[...]

  • Seite 60

    Part No. 0F1007 Revision F (07/25/05) Printed in U.S.A. Section 1 0 – W arranty Liquid-cooled 1 5, 20 and 2 5 kW Generators GENER AC PO WER SY STEMS "TWO YEAR" LIMITED WARR ANTY FOR QU I E TS OU RCE™ "PR EP A CKAGED EMERGENCY AUT OMA TIC ST ANDBY GENER A T ORS" F or a period of two years from the date of original sale, Gener[...]