Deutsch dropdown-ico

Graco 334558C Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Graco 334558C an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Graco 334558C, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Graco 334558C die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Graco 334558C. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Graco 334558C sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Graco 334558C
- Den Namen des Produzenten und das Produktionsjahr des Geräts Graco 334558C
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Graco 334558C
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Graco 334558C zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Graco 334558C und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Graco finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Graco 334558C zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Graco 334558C, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Graco 334558C widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    334558C EN Operation, Parts GH ™ 130/200/230/300 Hy draulic Sprayers For professio nal use only. Not approved for use in explo sive atmosphere or hazardo us locations. For portable airless spr aying of architectural paints and coatings. 3300 psi (22.8 MPa, 228 bar) Maximu m Working Pressure See page 3 for model information, including maxi mum wor[...]

  • Seite 2

    2 334558C Table of Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electric Moto r Kit Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 OEM Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

  • Seite 3

    Models 334558C 3 Models Electric Motor Kit Options *Performance is limited when usi ng electric motor vs gas engine OEM Kits GH130 Model: Standard 120V Motor Kit (Non CSA) 24W923  24W924  GH200 Model: Standard ProContractor 120V Motor Kit (Non C SA) 24W925  24W926  24W927  24W928  GH230 Model: Standard ProContractor 120V [...]

  • Seite 4

    Warnings 4 334558C Warnings The following warnings are for the setup, us e, groundin g, maintenance , and repair of this equipment. The exclamation point symbol alerts you to a general warning a nd the hazard symbols refer to procedure-specifi c risks. W hen these symbols appea r in the body of this manual or on wa rning labels, refe r back to thes[...]

  • Seite 5

    Warnings 334558C 5 W ARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solven t and paint fumes, in work area can ignite or explode. To help prevent fire and explo sion: • Do not spray flammable or combustible materials near an op en flame or sources of ignition such as cigarettes, motors, and electrical equipment. • Paint or solvent fl[...]

  • Seite 6

    Warnings 6 334558C Gas Engine Warnings W ARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solven t and paint fumes, in work area can ignite or explode. To help prevent fire and explo sion: • Use equipm ent only in well ventila ted area. • Do not fill fuel tank while en gine is runn ing or hot; shut off e ngine and let it cool. Fuel is [...]

  • Seite 7

    Warnings 334558C 7 Electric Motor/Gas Engine Warnings W ARNING SKIN INJECTION HAZARD High-pressure spray i s able to inject toxi ns into the body and cause serious bodi ly injury. In the event that injection occurs, get immediate surgica l treatment. • Do not aim the gun at, or spray any person or animal. • Keep hands and other body parts awa y[...]

  • Seite 8

    Warnings 8 334558C W ARNING EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Always wear appropriate gloves, eye protection, and a respirator or mask when painting. • Do not operate or spray near chi ldren. Keep chi ldren away from equipment at all times. • Do not overreach or stand on an unstab le support. Keep effective f[...]

  • Seite 9

    Warnings 334558C 9 W ARNING ENTANGLEMENT HAZARD Rotating parts ca n cause serious injury. • Keep clear of moving parts. • Do not operate equipment with protective guards or covers removed. • Do not wear loose clothing, jewelry or lo ng hair while op erating equipment. • Equipment can start without warning. Be fore checking, moving, or servi[...]

  • Seite 10

    Component Identification 10 334558C Component Identification Standard Models (GH130 , GH200, GH230, GH300) 2. 11. 12. 9. 1. 10. OFF ON 3. bar/MPa PSI on off 5. 4. 6. 7. ti25105a 8. 13. 14. 15. 9. 1 Engine Controls 2 Hydraulic Oil Cap / Dipstick 3 Pressure Control 4 Grounding Clamp 5 Threaded Pump Connection 6 Hydraulic Pump Valve 7 Inl et Strainer [...]

  • Seite 11

    Component Identification 334558C 11 Component Identification ProContractor Models (GH200, GH230, GH300) 2. 12. 9. 1. 10. OFF ON 3. bar/MPa PSI 14. on off 5. 6. 7. ti25106a 11. 4. 8. 13. 15. 16. 17. 11. 1 Engine Controls 2 Hydraulic Oil Cap / Dipstick 3 Pressure Control 4 Hydraulic Pump Valve 5 Hose Reel Handle 6 Hose Reel Lock 7 Grounding Clamp 8 P[...]

  • Seite 12

    Component Identification 12 334558C Grounding Procedure for Gas Engine To ground sprayer: Attach sprayer grounding clamp to earth ground. Air and fluid hoses: Use only electri cally conductive hoses with a maximum of 500ft. (150 m) combined hose length to ensure grounding continuity. Check electrical resistance of hoses. If total resistance to grou[...]

  • Seite 13

    Pressure Relief Procedure 334558C 13 Grounding of Pails Solvent pails used w hen flushing: Follow local code. Use only conductive metal pail s, placed on a grounded surface. Do not pl ace the pail on a n on-conductive surface, such as paper or cardboard, whi ch interrupts grounding continuity. Always ground a met al pail: connect a ground wire to t[...]

  • Seite 14

    Setup 14 334558C Setup Change Engine or Motor 1 Turn motor OFF and unplug or turn engine switch OFF. Loosen belt gua rd knob and moto r clamp. Perform Pressure Relief Procedur e , page 13. 2 Lift belt guard. Remove belt. Tilt engine/motor and remove engine/motor. 3 Tilt engine/motor. Install engine/motor. Install belt. Lower belt guard. 4 Swivel mo[...]

  • Seite 15

    Setup 334558C 15 ti22700a Complete Setup 1. All sprayers except ProContractor : Connect appropriate Graco high-pressure ho se to sprayer. 2. Install hose to spray gun and tighten securely. 3. Engage gun trigger lock. 4. Remove Tip Guard. 5. ProContractor Series: Install inlet strainer into bottom of suction tube, place inlet nut over e nd and hand [...]

  • Seite 16

    Setup 16 334558C 7. Fill throat packing nut with TSL to prevent premature packing wear. Do this each time you spray. 8. Check engine oil level. 9. Fill fuel tank. 10. Check hydraulic oi l level. Add Graco Hydraulic Oil, ISO Grade 46, 1692 36 (5 gallon/18.9 liter) or 207428 (1 gallon/3.8 liter). Hydraulic tank capacity is 1.25 gallon (4.75 liters). [...]

  • Seite 17

    Startup 334558C 17 Startup 1. Place suction tube and drain tube in grounded metal pail partially filled with flushing fluid. Attach gr ound wire to pail and to earth ground. 2. Turn prime valve dow n to DRAIN position. Turn pressure contro l counterclockwise to lowest pressure. 3. Set hydraulic pump valve OFF. 4. If using electric motor, plug cord [...]

  • Seite 18

    Startup 18 334558C d. Set engine switch to ON. e. Pull starter rope. f. After engine starts, move choke to open. g. Set throttle to desired setting. h. Set hydraulic pump valve ON (hydraulic motor is now active). 6. Increase pressure enough to start hydraulic motor stroking and allow fluid to circulate for 15 se conds; turn pressure down, turn prim[...]

  • Seite 19

    Startup 334558C 19 9. Inspect for leaks. If leaks occur, turn sprayer OFF immedi ately. Perform Pressure Relief Procedur e , page 13. Tighten leaky fittings. R epeat Startup procedure steps 2-8. If no leaks, continue to trigger gun until system is thoroughly flushed. 10. Place siphon tube in paint pail. 11. Trigger gun again into flushing fluid pai[...]

  • Seite 20

    Startup 20 334558C Switch Tip ™ and Guard Assembly 1. Perform Pressure Relief Procedure , page 13. 2. Engage gun trigger lock. Insert Switch Tip. Insert seat and OneSeal™. 3. Insert Switch Tip and face forward. 4. Screw assembly onto gun. Tighten. Spray 1. Spray test pattern. Increase pressure to eliminate heavy edges. Use smaller tip size if p[...]

  • Seite 21

    Startup 334558C 21 Clear Tip Clog 1. Release trigger, engage trigge r lock. Rotate Switch Tip. Disengage trigger lock. Trigger gun to clear clog. 2. Engage trigger lock. Return Switch Tip to original position. D isengage trigger lock and continue spra ying. Hose Reel (ProContractor Series only) 1. Make sure hose is routed through hose guide. 2. Lif[...]

  • Seite 22

    Clean Up 22 334558C Clean Up 1. Perform Pressure Relief Procedure , page 13, steps 1-7. 2. Remove Guard and SwitchTip. 3. Remove siphon tube set from paint and place in flushin g fluid. Use water for water-based paint and mineral sp irits for oil based paint. 4. Turn engine ON a nd start engine or plug motor in and turn ON. Turn hydraulic pump valv[...]

  • Seite 23

    Clean Up 334558C 23 8. Raise siphon tube a bove flushing fluid and run sprayer for 15 to 30 seconds to drain fluid . Turn hydrau lic valve OFF. Turn engine OFF or tu rn electric motor OFF and unplug. 9. Engage trigger lock. Re move filters from gun and sprayer, if installed. Clean and inspect. Reinstall filte rs. 10. Depending on model, either remo[...]

  • Seite 24

    Maintenance 24 334558C Maintenance NOTE: For detailed engi ne maintenance and specifications, refe r to separate Honda Engines Owner’s Manual, sup plied. DAILY: Check engine oil level and fill as necessary. DAILY: Check hydraulic oil level and fill as necessary. DAILY: Check hose for wear and damage. DAILY: Check gun trigger lock for proper opera[...]

  • Seite 25

    Troubleshooting 334558C 25 Troubleshooting Problem Cause Solution Gas engine pulls hard (won’t start) Hydraulic pressure is too high Turn hydraulic pressure knob counterclockwise to lowest setting Gas engine does not start Switch OFF, low oil, no gasoline Consult engine manual Fuel shut off valve closed Open fuel shut off valve Gas engine does no[...]

  • Seite 26

    Troubleshooting 26 334558C Displacement pump operates, but output is low on down stroke and/or on both strokes Piston packings worn or damaged Tighten packing nut or replace packings. See manual 334654 Intake valve ball check not seating properly Service intake valve ball check. See manual 334654 Suction tube air leak Hydraulic oil filter is dirty [...]

  • Seite 27

    Standard Series Pump 334558C 27 Standard Series Pump Removal See pump manual 334654 for pump repair. 1. Flush pump. 2. Perform Pressure Relief Procedure , page 13. 3. Remove suction tu be and paint hose (remove at swivel end). 4. Push retaining ring up; push out pin. 5. Loosen jam nut. Unscrew pump. Installation 1. Screw jam nut to bottom of pump t[...]

  • Seite 28

    ProContractor Series Pump 28 334558C 2. Slowly pull engine starter rope until pump rod pin hole is aligned with hydraulic rod hole. Push pin into hole. Push retaining ring into groove. 3. Fill packing nut with Graco TSL. ProContractor Series Pump Removal See pump manual 334654 for pu mp repair. 1. Flush pump. 2. Perform Pressure Relief Procedure , [...]

  • Seite 29

    ProContractor Series Pump 334558C 29 5. Slide coupler cover up to fully exp ose rod couplers. 6. Remove rod couplers. 7. Remove pin. NOTE: Support pump with your hand before opening t-handle. 8. Open clamp. 9. Remove pump from unit. Installation 1. If needed, place pump rod in adjustment casting and pull pump to extend rod. 2. Reverse removal steps[...]

  • Seite 30

    Notes 30 334558C Notes[...]

  • Seite 31

    Parts 334558C 31 Parts GH ™ 130/200/230/300 Standard Series ti25097a[...]

  • Seite 32

    Parts 32 334558C 234 233 232 228 231 230a 229 62 61 60 59 58 57 11 6 200 174 70 39 180 54 150a 150b 150c 150d 150f 150e 150g 63 103 227 11 2 75 35 182 81 79 132 91 199 200 213 215 217 216 ti25433a 237 235 236 Parts GH ™ 130/200/230/300 Standard Series 234 233 232 228 231 230a 229 62 61 60 59 58 57 11 6 200 174 70 39 180 54 150a 150b 150c 150d 150[...]

  • Seite 33

    Parts 334558C 33 Parts List  Danger and Warning labels are available at no cost.  Included in Drain Valve Replacement Kit 235014  Included in Drain Valve Replacement Kit 245103 ‡ Included in Filter Replacem ent Kit 24W753 Ref. Part Description Qty. 35 112827 BUTTON, snap 2 39 119420 WHEEL, pneumatic, GH130 & 200 2 119509 WHEEL, pneum[...]

  • Seite 34

    Parts 34 334558C Parts - Engines GH ™ 130/200/230 Standard Series 88 24 7 154 153 99 154 23 34 30 43 133 106 126 11 9 88 24 7 154 153 126 99 154 23 34 30 43 133 106 11 9 162 160 161 ti25491a 90 90 GH ™ 300 Standard Series Torque to 120-130 in-lbs (13.6-14.7 N·m) Torque to 58-62 in-lb s (6.6-7.0 N·m) Loctite 242 1 2 3 Torque to 120-130 in-lbs [...]

  • Seite 35

    Parts 334558C 35 Parts List *Engine Repair Kits:  Danger and Warning labels are available at no cost. Ref. Part Description Qty. 7 100023 WASHER, flat, GH130, 200 & 230 4 100132 WASHER, flat, GH300 4 23 113664 SCREW, cap, hex hd, GH130, 200 & 230 4 106212 SCHREW, cap, hex hd, GH300 4 24 110838 NUT, lock, GH130, 200 & 230 4 101566 NUT[...]

  • Seite 36

    Parts 36 334558C Parts - Fan Belt GH ™ 130/200/230/300 Standard Series 224 223 222 225 221 226 56 220 21 1 214 212 219 44 287 139 209 278 277 207 206 203 2 186 201 144 204 55 170 55 11 5 200 184 101 96 176 11 7 148 51 172 48 173 ti25434a 139 294 295 296 299 Torque to 120-130 in-lbs (13.6-14.7 N·m) Loctite 242 Torque 58-62 in-lbs (6.6-7.0 N·m) T[...]

  • Seite 37

    Parts 334558C 37 Parts List Ref. Part Description Qty. 2 101754 PLUG 1 44 119433 BELT, GH130, 200, 230 1 119432 BELT, GH300 1 48 867539 SCREW, hex head 2 51 117284 GRILL, fan guard 1 55 17D813 NUT, hand 2 56 154594 O-RING 1 96 15E410 PULLEY, fan 1 101 17D031 LABEL, GH130 1 17D032 LABEL , GH200 1 17D034 LABEL , GH230 1 17D036 LABEL , GH300 1 115 288[...]

  • Seite 38

    Parts 38 334558C Parts GH ™ 130/200/230/300 Standard Series 198 ti25127a Torque to 70-80 ft-lbs (94.9-108.5 N·m) 1 1[...]

  • Seite 39

    Parts 334558C 39 Parts List Ref. Part Description Qty. 63 243814 HOSE, coupled 1 86 193031 NUT, retaining, GH130 1 193394 NUT, retaining, GH200/230/300 1 89 15D000 CLIP, drain line 1 92 155141 PIN, pump, GH130 1 197443 PIN, pump, GH200/230/300 1 103 288732 KIT, drain hose 1 110 241920 DEFLECTOR, threaded 1 111 24B748 PUMP, kit, displacement, GH130 [...]

  • Seite 40

    Parts 40 334558C Parts GH ™ 130/200/230/300 Standard Series 272 293 271 266 ti25128a 246 245 243 239 242 289 143 283 244 239 283 Sprayers OEM Kits Torque to 145-155 ft-lbs (196.6-210.2 N·m) Torque to 12-18 ft-lbs (16.3-24.4 N·m) Torque to 140-160 in-lb s (15.8-18.1 N·m) 1 2 3 2 1 1 3[...]

  • Seite 41

    Parts 334558C 41 Parts List Ref. Part Descriptio n Qty. 129  15B063 LABEL, warning, hot surface 1 143  17D050 LABEL, GH130 1 17D051 LABEL, GH200 1 17D053 LABEL, GH230 1 17D055 LABEL, GH300 1 239  15H953 MANIFOLD, GH130 1 15A728 MANIFOLD, GH200 1 15E243 MANIFOLD, GH230 & 300 1 242  15B564 SCREW, cap socket 4 243‡  117739 W[...]

  • Seite 42

    Parts 42 334558C Parts GH ™ 130/200 Standard Series w/ Spray Gun and Hose GH ™ 230/300 Standard Series w/ Spray Gun and Hoses Ref. Part No. Description Qty. 202 240794 HOSE, grounded, nylon; 1/4 in. ID;cpld 1/4-18 npsm; 50 foot (15 m); spring guards both ends 3300 psi (227 bar, 22.7 MPa) 1 203 288420 Con tractor Spray Gun Includes 517 RAC ® X [...]

  • Seite 43

    Parts 334558C 43 Parts GH ™ 200/230/300 ProContractor Series (OEM Kits) ti25104a[...]

  • Seite 44

    Parts 44 334558C Parts GH ™ 200/230/300 ProContractor Series 234 233 232 228 231 229 11 6 200 174 70 39 180 54 150a 150b 150c 150d 150f 150e 150g 63 227 79 199 200 213 215 217 216 ti25131a 230a 237 238 240 272 91 230a 266 Torque to 120-130 in-lbs (13.6-14.7 N·m) Inflate tires to 25-35 psi (1.7-2.4 bar) Torque 110-120 in-lbs (12.4-13.6 N·m) Torq[...]

  • Seite 45

    Parts 334558C 45 Parts List  Danger and Warning labels are available at no cost.  Included in Drain Valve Replacement Kit 245103 ‡ Included in Filter Replacem ent Kit 24W753 Ref. Part Description Qty. 39 119509 WHEEL, pneumatic 2 54 156306 WASHER, flat 2 63 243814 HOSE 1 70 120211 CLIP, retaining 2 79  189246 LABEL, warning 1 17D947 LABE[...]

  • Seite 46

    Parts 46 334558C Parts - Engines GH ™ 200/230 ProContractor Series 88 24 7 154 153 99 154 23 34 30 43 133 106 126 11 9 88 24 7 154 153 126 99 154 23 34 30 43 133 106 11 9 162 160 161 ti25491a 90 90 GH ™ 300 ProContractor Series Torque to 120-130 in-lbs (13.6-14.7 N·m) Torque to 58-62 in-lbs (6.6-7.0 N·m) Loctite 242 1 2 3 Torque to 120-130 in[...]

  • Seite 47

    Parts 334558C 47 Parts List *Engine Repair Kits:  Danger and Warning labels are available at no cost. Ref. Part Description Qty. 7 100023 WASHER, flat, GH200 & 230 4 100132 WASHER, flat, GH300 4 23 113664 SCREW, cap, hex hd, GH200 & 230 4 106212 SCHREW, cap, hex hd, GH300 4 24 110838 NUT, lock, GH200 & 230 4 101566 NUT, lock, GH300 4[...]

  • Seite 48

    Parts 48 334558C Parts - Fan Belt GH ™ 200/230/300 ProContractor Series 224 223 222 225 221 226 56 220 21 1 214 212 219 44 287 139 209 278 277 207 206 203 2 186 201 144 204 55 170 55 11 5 200 184 101 96 176 11 7 148 51 172 48 173 ti25457a 139 294 297 296 299 Torque to 120-130 in-lbs (13.6-14.7 N·m) Loctite 242 Torque 58-62 in-lbs (6.6-7.0 N·m) [...]

  • Seite 49

    Parts 334558C 49 Parts List Ref. Part Description Qty. 2 101754 PLUG 1 44 119433 BELT, GH200, 230 1 119432 BELT, GH300 1 48 867539 SCREW, hex head 2 51 117284 GRILL, fan guard 1 55 17D813 NUT, hand 2 56 154594 O-RING 1 96 15E410 PULLEY, fan 1 101 17D032 LABEL , GH200 1 17D034 LABEL , GH230 1 17D036 LABEL , GH300 1 115 288261 RAIL, belt guard, assem[...]

  • Seite 50

    Parts 50 334558C Parts GH ™ 200/230/300 ProContractor Series ti25132a Torque to 90-110 in-lbs (10.2-12.4 N·m) 1 1[...]

  • Seite 51

    Parts 334558C 51 Parts List Ref. Part Description Qty. 63 243814 HOSE, coupled 1 111 24W996 PUMP, kit, displacement, GH200 1 24W998 PUMP, kit, displacement, GH230 & 300 1 114 288252 HOSE, suction, 5 gallon, GH200, 230 & 300 1 115 289669 HOSE, suction, 30/55 gal- lon, GH200/230/300 (not shown) 1 179 277377 COUPLER 2 186 107505 PACKING, o-rin[...]

  • Seite 52

    Parts 52 334558C Parts GH ™ 200/230/300 ProContractor Series 272 293 271 266 ti25456a 246 245 243 242 239 292 283 143 283 289 244 Sprayers OEM Kits Torque to 145-155 ft-lbs (196.6-210.2 N·m) Torque to 12-18 ft-lbs (16.3-24.4 N·m) Torque to 140-160 in-lbs (15.8-18.1 N·m) 1 2 3 2 1 1 3[...]

  • Seite 53

    Parts 334558C 53 Parts List Ref. Part Descriptio n Qty. 129  15B063 LABEL, warning, hot surface 1 143  17D051 LABEL, GH200 1 17D053 LABEL, GH230 1 17D055 LABEL, GH300 1 239  15J278 MANIFOLD, GH200 1 15J279 MANIFOLD, GH230 & 300 1 242  15B564 SCREW, cap socket 4 243‡  117739 WIPER, rod 1 244‡  112342 BEARING, rod 1 24[...]

  • Seite 54

    Parts 54 334558C Parts GH ™ 200 ProContractor Series Spray Gun and Hoses (Assembled on Hose Reel) GH ™ 230 ProContractor Series Spray Gun and Hoses (Assembled on Hose Reel) Ref. Part No. Description Qty. 202 240794 HOSE, grounded, nylon; 1/4 in. ID;cpld 1/4-18 npsm; 50 foot (15 m); spring guards both ends 3300 psi (227 bar, 22.7 MPa) 2 203 2884[...]

  • Seite 55

    Parts 334558C 55 GH ™ 300 ProContractor Series Spray Gun and Hoses (Assembled on Hose Reel) Hose Reel (ProContractor Series) Ref. Part No. Description Qty. 302 240797 HOSE, gro unded, nylon; 3/8 in. ID;cpld 3/8-18 npsm; 50 foot (15 m); spring guards both ends 3300 psi (227 bar, 22.7 MPa) 1 303 241735 HOSE, grounded , nylon; 1/4 in. ID; cpld 1/4 n[...]

  • Seite 56

    Technical Data 56 334558C Technical Data GH ™ 130 Standard Series US Metric Maximum fluid working pressure . . . . . . . . 3300 psi 22.8 MPa, 228 bar Hydraulic reservoir ca pacity . . . . . . . . . . . . 1.25 gallons 4.75 liters Maximum hydraulic pressure . . . . . . . . . . . 1510 psi 10.4 MPa,1 04 bar Engine . . . . . . . . . . . . . . . . . . [...]

  • Seite 57

    Technical Data 334558C 57 GH ™ 200 Standard Series US Metric Maximum fluid working pressure . . . . . . . . 3300 psi 22.8 MPa, 228 bar Hydraulic rese rvoir capac ity . . . . . . . . . . . . 1 .25 gallons 4.75 liters Maximum hydraulic pressure . . . . . . . . . . . 1855 psi 12.8 MPa,128 bar Engine . . . . . . . . . . . . . . . . . . . . . . . . . [...]

  • Seite 58

    Technical Data 58 334558C GH ™ 230 Standard Series US Metric Maximum fluid working pressure . . . . . . . . . 3300 psi 22.8 MPa, 228 bar Hydraulic rese rvoir capaci ty . . . . . . . . . . . . 1.25 gallons 4.75 liters Maximum hydraulic pressure . . . . . . . . . . . 1855 psi 12.8 MPa,128 bar Engine . . . . . . . . . . . . . . . . . . . . . . . . .[...]

  • Seite 59

    Technical Data 334558C 59 Basic Sprayer Wetted Parts: Zinc and nickel-plated carbon steel, stainless steel, PTFE, acetal, chrome plating, leather, V-Maxt UHMWPE, stainless steel, tungsten ca rbide, ceramic, nylon, aluminum GH ™ 300 Standard Series US Metric Maximum fluid working pressure . . . . . . . . 3300 psi 22.8 MPa, 228 bar Hydraulic rese r[...]

  • Seite 60

    Technical Data 60 334558C GH ™ 200 ProContractor Series US Metric Maximum fluid working pressure . . . . . . . . . 3300 psi 22.8 MPa, 228 bar Hydraulic rese rvoir capaci ty . . . . . . . . . . . . 1.25 gallons 4.75 liters Maximum hydraulic pressure . . . . . . . . . . . 1855 psi 12.8 MPa,128 bar Engine . . . . . . . . . . . . . . . . . . . . . . [...]

  • Seite 61

    Technical Data 334558C 61 GH ™ 230 ProContractor Series US Metric Maximum fluid working pressure . . . . . . . . 3300 psi 22.8 MPa, 228 bar Hydraulic rese rvoir capac ity . . . . . . . . . . . . 1 .25 gallons 4.75 liters Maximum hydraulic pressure . . . . . . . . . . . 1855 psi 12.8 MPa,128 bar Engine . . . . . . . . . . . . . . . . . . . . . . .[...]

  • Seite 62

    Technical Data 62 334558C Basic Sprayer Wetted Parts: Zinc and nickel-plated carbon steel, stainless steel, PTFE, acetal, ch rome plat ing, leather, V-Maxt UHMWPE, stainless steel, tungsten ca rbide, ceramic, nylon, aluminum GH ™ 300 ProContractor Series US Metric Maximum fluid working pressure . . . . . . . . . 3300 psi 22.8 MPa, 228 bar Hydraul[...]

  • Seite 63

    Technical Data 334558C 63 Technical Data 2.25 in. (57.15 mm) 1.813 in. (46.05 mm) 1.813 in. (46.05 mm) 3/4 - 14 NPT Male 2.25 in. (57.15 mm) 1.813 in. (46.05 mm) 2.25 in. (57.15 mm) ti24313b Hydraulic Return, 37º flare, 3/4-16 UNF-2A Hydraulic Inlet, 37º flare, 3/4-16 UNF-2A Mounting Screws (4), Socket Cap Screw 1 in. 3/8-16 UNC Paint Outlet, 90?[...]

  • Seite 64

    Graco Standard Warranty 64 334558C Graco Standard Warranty Graco warrants all equipment referenced in this docu men t which is manufactured by Graco and bearing its name to be free from defects in mater ial and work manship on the date of sale to the original pur chaser for use. With the exception of any special, extended, or limited warranty publi[...]

  • Seite 65

    All written and visual data containe d in this document reflects the latest p roduc t information available at the time of publication. Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English. MM 334558 Graco Headquarters: Minneapoli s International Offices: Belgium, China, Japan, Kor[...]