Grizzly G0513X2 Bedienungsanleitung
- Schauen Sie die Anleitung online durch oderladen Sie diese herunter
- 84 Seiten
- 13.15 mb
Zur Seite of
Ähnliche Gebrauchsanleitungen
Richtige Gebrauchsanleitung
Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Grizzly G0513X2 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Grizzly G0513X2, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.
Was ist eine Gebrauchsanleitung?
Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Grizzly G0513X2 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.
Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Grizzly G0513X2. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.
Was sollte also eine ideale Gebrauchsanleitung beinhalten?
Die Gebrauchsanleitung Grizzly G0513X2 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Grizzly G0513X2
- Den Namen des Produzenten und das Produktionsjahr des Geräts Grizzly G0513X2
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Grizzly G0513X2
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen
Warum lesen wir keine Gebrauchsanleitungen?
Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Grizzly G0513X2 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Grizzly G0513X2 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Grizzly finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Grizzly G0513X2 zu überspringen, wie es bei der Papierform passiert.
Warum sollte man Gebrauchsanleitungen lesen?
In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Grizzly G0513X2, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.
Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Grizzly G0513X2 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.
Inhaltsverzeichnis der Gebrauchsanleitungen
-
Seite 1
COPYRIGHT © MAY, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL9289 PRINTED IN TAIWAN The Model G05 1 3X2 is the same machine as the Model G05 1 3 X ex cept f or the cast iron trunnion assembly . Except fo r details giv en in th[...]
-
Seite 2
-2 - G05 1 3 X2 Manual Inser t G0 5 1 3 X 2 Mai n P ar ts ?[...]
-
Seite 3
G05 1 3 X2 Manual Inser t -3 - G0 5 1 3 X 2 Fen ce / Gu ides P arts ?[...]
-
Seite 4
- 4 - G05 1 3 X2 Manual Inser t G0 5 1 3 X 2 P ar ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0513X001 BUSHING 54 PCB23M CARRIAGE BOLT M8-1.25 X 80 2 PSS01M SET SCREW M6-1 X 10 55 P0513055 UPPER WHEEL COVER 3 P0513X003 BUSHING 56 PB10M HEX BOLT M6-1 X 25 4 P0513004 LIFTING EYE BOLT M10-1.5 57 PW03M FLAT WASHER 6MM 5 P0513005 MACHINE B[...]
-
Seite 5
G05 1 3 X2 Manual Inser t -5 - REF PART # DESCRIPTION REF PART # DESCRIPTION 99 PN02M HEX NUT M10-1.5 127 P0513X127 TABLE INSERT 100 P0513100 SMALL GEAR 128 P0513X128 TABLE PIN 101 P0513X101 LOCK HANDLE 129 P0513X129 LOCATE BUSHING 102 P0513102 TRUNNION SUPPORT BRACKET 130 P0513X130 BUSHING 103 PLW06M LOCK WASHER 10MM 131 PSBS01M BUTTON HD CAP SCR [...]
-
Seite 6
- 6 - G0 5 1 3X2 M anual Insert REF PART # DESCRIPTION REF PART # DESCRIPTION 167 PB07M HEX BOLT M8-1.25 X 25 178 P0513X2178 TRUNNION SUPPORT BRACKET 168 P0513X101 LOCK HANDLE M8-1.25 179 P0513100 SMALL GEAR 169 PW05M FLAT WASHER 4MM 180 PSBS19M BUTTON HD CAP SCR M10-1.5 X 30 170 P0513120 POINTER 181 P0513X2181 RIGHT COVER 171 PS17M PHLP HD SCR M4-[...]
-
Seite 7
G05 1 3 X2 Manual Inser t - 7 - ?[...]
-
Seite 8
-8- G05 1 3 X2 Manual Inser t ?[...]
-
Seite 9
MO DE L G0 5 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 E X T RE ME SE RIE S B AN DS A W O WNER'S MANU AL COPYRIGHT © JAN UAR Y , 2 00 6 BY G RIZ ZL Y IN DUSTRIAL , IN C. RE VISED FEBRUAR Y , 20 07 ( TR) W ARN I NG : NO P OR TI O N OF T HI S M AN UAL M A Y B E REPR OD UCE D I N AN Y SH APE OR FOR M W IT HO UT T HE W RI T TEN A PPROV A L OF G RI Z Z L [...]
-
Seite 10
?[...]
-
Seite 11
T able of Con te nts INTRODUCTION ............................................................................................................................... 3 Foreword .................................................................................................................................... 3 Contact Info .............................[...]
-
Seite 12
SECTION 5: ACCESSORIES ......................................................................................................... 43 SECTION 6: MAINTENANCE ........................................................................................................ 45 Schedule ..............................................................................[...]
-
Seite 13
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -3 - If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C / O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 We stand behind our machines. If you have any service questions or parts requests, please [...]
-
Seite 14
- 4 - G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model G0513X MACHINE DATA SHEET Cu[...]
-
Seite 15
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -5 - The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 2 Model G0513X Table Information Tabl[...]
-
Seite 16
- 6 - G0 5 1 3X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series Band saw G0 5 1 4 X Mach i ne Data Sheet The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Mo[...]
-
Seite 17
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 7 - The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 2 Model G0514X Table Information Tab[...]
-
Seite 18
-8- G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model G0514X3 MACHINE DATA SHEET Cus[...]
-
Seite 19
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -9 - The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 2 Model G0514X3 Table Information Tab[...]
-
Seite 20
- 1 0 - G 05 1 3 X / G0 5 1 4 X / G05 1 4 X3 Ex treme Series Bands aw Figure 2. Bandsaw back view. A. Tension Indicator Window B. ON/OFF Switch C. Rip Fence D. Fence Locking Lever E. Dust Port 4" F. Miter Gauge G. Blade Tension Handwheel H. Ball Bearing Roller Guides I. Guide Post J. Guide Post Handwheel K. Blade Tracking Window Identi f ica t[...]
-
Seite 21
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 1 1 - 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5. WEAR PROPER APPAREL. DO N OT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to con - ta[...]
-
Seite 22
- 1 2- G05 1 3X / G05 1 4X / G05 1 4X 3 E x treme Series Bandsaw 7. ONLY ALLOW TRAINED AND PROP- ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe dis- tance from the work area. 9. MAKE WORKSHOP CHILD PROOF. Use [...]
-
Seite 23
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 1 3 - A ddit io na l Safe t y Instr uctio n s fo r Ban dsa w s 7. BLADE SPEED. Allow blade to reach full speed before cutting. 8. LEAVING WORK AREA. Never leave a machine running and unattended. Allow the bandsaw to come to a complete stop be - fore you leave it unattended. 9. FEED RA[...]
-
Seite 24
- 1 4- G0 5 1 3X / G05 1 4 X /G 05 1 4X 3 Ex treme Series Bandsaw Serious p erson al injury could oc cur if you connect the machine to t he power source before you h av e compl eted the set up pro - cess . DO NOT conne ct the ma chine to th e power source until instruct ed to do so. Operati on S E C T I O N 2: C I R C U I T R E Q U I R E M E N T S [...]
-
Seite 25
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 1 5 - In the ev ent of an ele ctric al shor t, grounding reduces the r isk of electri c shock . The grounding wire in t he p owe r c ord must be properly connec t - ed to the grounding prong on the plug ; like wise , the out let must be properly installed and ground - ed. All elec tri[...]
-
Seite 26
- 1 6 - G0 5 1 3X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw The Model G0 5 1 3X / G0 5 1 4 X / G0 5 1 4 X 3 was c are- fully packed when it left our wa rehouse. If you dis cover the mach ine i s d amage d af ter you ha ve sig ned for delivery , ple ase imm ediately cal l Customer Servic e at ( 5 7 0) 5 46 - 9 66 3 for advice. Sav e t he [...]
-
Seite 27
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 1 7 - In v ent o r y After all the par ts hav e been removed from t he crate , you should hav e the following items: Crate Conte nts ( Figur e 7 & 8 ): Qt y A . Bandsaw (not shown) ................................. 1 B. T able ......................................................[...]
-
Seite 28
- 1 8 - G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X3 Ex treme Series B andsaw Hard w are Reco gn i ti on Ch ar t[...]
-
Seite 29
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 1 9 - Figure 9. G0 5 1 3X minimum working c learances. Fl oo r Loa d Refe r to the Machine Data She et for t he weight and foot print spec ific atio ns of your mac hine. Some floors ma y r equire a dditio nal rein forcement to sup por t b oth the machine and o perator . Wo rk ing Clea[...]
-
Seite 30
-20- G 05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series Band saw Mo vi n g & P la c in g Ba se Un i t Figure 11. Lifting the bandsaw. This is an extrem ely heav y machine. Serious per sonal injury may occur if safe moving methods are not followed. T o b e safe, you will ne ed assist ance and a forklift or a hoist when removing the machine f[...]
-
Seite 31
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 2 1 - Figure 14. Quick release tension lever. Tighten Loosen 2. Adjust the upper and lower blade guides away from the blade. Refer to Adjusting Blade Guide Bearings on Page 29 for more details. 3. Open the upper and lower wheel covers, and slide the blade off of both wheels. All saw b[...]
-
Seite 32
-22- G05 1 3X /G 05 1 4X/ G0 5 1 4 X3 Ex treme Series B andsaw Bl ade T rac ki n g Personal injury or death can occur if the machine starts while your hand is touching the bandsaw wheel during tracking adjustments. Disconnect power from the bandsaw before performing blade tracking adjustments. The blade tracking is primarily affected by the tilt of[...]
-
Seite 33
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -23- The p ositive stop allows the table to be quick ly and acc urately returned t o t he horizontal (0˚) position af ter being adjusted to a dif feren t angle. Compone nts and H ardware Ne ede d : Qt y Hex Bolt M8-1.25 x 90 ....................................... 1 Hex Nut M8-1.25 ...[...]
-
Seite 34
-2 4- G0 5 1 3X / G05 1 4X / G05 1 4X 3 E x treme Series Bandsaw Figure 20. Squaring table to blade. 5. Adjust the positive stop bolt to the table and secure it by tightening the hex nut against the trunnion bracket. 6. Check the adjustment for accuracy once you have tightened the hex nut. 7. Loosen the screw on the pointer, but do not remove it. 8[...]
-
Seite 35
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -25- 3. Install an M8-1.25 hex nut on the fence handle, then thread the handle into the fence assembly ( Figure 23 ). Tighten the hex nut against the fence pivot block to secure the handle. Figure 23. Handle installed on fence assembly. Hex Nut Pivot Block 4. Thread the M6-1 hex nut ont[...]
-
Seite 36
-26- G0 5 1 3X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw 7. Tighten the lock handle. 8. Pull the fence handle up and place the fence assembly on the fixed rail as shown in Figure 26 . Figure 26. Correctly installed fence. 6. Slide the resaw fence over the moving plate, as shown in Figure 25 , so the moving plate fits inside the channel o[...]
-
Seite 37
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 27 - T ensi o ni ng Bl ade A properly tensioned blade is essential for mak - ing accurate cuts and is required before mak - ing many band saw adjustments. (Ev ery time you replace the blade, y ou should perform this proce - dure be cause all blades tension dif ferently .) To tension t[...]
-
Seite 38
-28- G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X3 Ex treme Series B andsaw 5. Tighten the assembly cap screw. 6. Loosen the cap screw on the support bearing adjustment shaft. 7. Place a 0.016" feeler gauge between the support bearing and the blade, and position the bearing 0.016" away from the back of the blade as illustrated in Figure 29 . Figur[...]
-
Seite 39
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -29- The b lade guid es pro vide side -to- side suppor t to help k eep the blade straight while cutting. The blade guid es are d esigned to be adjusted in t wo wa ys— for ward / back ward and side-to -si de. To adjust the upper and lower blade guides : 1. Make sure the blade is tracki[...]
-
Seite 40
-3 0 - G0 5 1 3X / G05 1 4 X /G 05 1 4X 3 E x treme Series Bandsaw NOTICE Make sure that the blade teeth will not con- tact the guide bearings when the blade is against the rear support bearing during the cut or the blade teeth will be ruined. 5. Tighten the cap screw on the lateral adjust- ment rod. 6. Loosen the bearing rotation adjustment cap sc[...]
-
Seite 41
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -3 1 - T o ensure cutt ing a ccuracy when the fence is fi rst installed, the fence should be aligned with t he miter slot. To align the fence parallel with the miter slot: 1. If the fence is mounted on the left-hand side of the blade, remove it and remount it next to the miter slot. 2. [...]
-
Seite 42
-32- G05 1 3 X / G05 1 4 X /G 05 1 4X 3 E x treme Series Bandsaw Damag e to your eyes, lungs, and ears could re su lt fro m us ing thi s ma ch in e wi th ou t prope r protec tive ge ar . Always wear safet y glasses , a respirator , and hearing protection when op erat ing t his machine. Lo o s e h a ir a n d c lo t h - ing could get caught in machin[...]
-
Seite 43
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -33 - Guide Post Lock Knob Guide Post Handwheel The ST ART / ST OP switch on t he Model G0 5 1 3X / G05 1 4X/ G0 5 1 4 X3 is located on the column fo r easy access ( Figures 37 & 3 8 ). Immediately turn the machine OFF i f there becomes a safe t y hazard. ST ART / ST OP Swit ch Figu[...]
-
Seite 44
-3 4- G 05 1 3 X / G05 1 4 X /G 05 1 4X 3 Ex treme Series Bandsaw Bl ade Lead Bandsaw blades c ommonly wander of f the cut line when sawing, as shown in Figure 41 . This is called blade lead. Blade lead is commonly caused b y too fast o f a f eed rat e, a dull or abused blade, or improper tension. If y our blade is sharp / undamaged and you still h[...]
-
Seite 45
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -35 - 3. Clamp the board to the bandsaw table with- out moving it. Now slide the fence over to the board so it barely touches one end of the board. 4. Loosen the four cap screws on top of the fence. 5. Skew the fence so it is parallel to the edge of the scrap piece. You may need to re-a[...]
-
Seite 46
-3 6 - G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X3 Ex treme Series B andsaw Cr oss c uttin g Crosscut ting is the proces s of cut ting across the grain of wood. For ply wood and other proc essed wood, crossc utt ing simply means cut ting across the width of the mat erial. T o make a 90˚ crosscut : 1. Mark the workpiece on the edge where you want to begin[...]
-
Seite 47
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -37 - Figure 45. Resawing lumber. Resawing ( Figure 45 ) is the proc ess of cut ting a board into two or more t hinner boards. The ma xi - mum boa rd width that can be r esawn is limited by the ma ximum cut ting height of the bandsaw . One of t he most im por tant consid erations when r[...]
-
Seite 48
-3 8- G 05 1 3 X / G0 5 1 4 X / G05 1 4 X3 Ex treme Series Bands aw Stac k ed Cu ts One of the benefits of a bandsaw is it s abilit y to cut multiple copies of a pa r ticular shape b y stack - ing a number of workpieces together . Before mak - ing stacked c uts, ensure t hat both the t able and the blade are properly adjust ed to 90° . Other wise,[...]
-
Seite 49
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -39 - Bl ade Spe ed The blade speed can be adjusted to 1 700 o r 350 0 FP M. Speed adjustments are made by moving the V -belt position on the motor and wheel pul - ley s. Most woodcut ting can be per formed succes sfully at the higher b lade s peeds. Slower blade spee ds generally produ[...]
-
Seite 50
- 40 - G 05 1 3 X / G05 1 4 X /G 05 1 4X 3 E x treme Series Bandsaw Bl ade Inf orm ati o n Selecting the right blade requires a knowledge of the various blade characteristics to match t he blade with the par ti cular cut ting op eration. Bl ad e Len gth Measured by the circumference , bla de lengths are u sually unique to the brand of your bandsaw [...]
-
Seite 51
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 4 1- • Hook : The teeth on this style have a posi- tive angle (downward) which makes them dig into the material, and the gullets are usu - ally rounded for easier waste removal. These blades are excellent for the tough demands of resawing and ripping thick material. To ot h Pit ch U[...]
-
Seite 52
- 42- G05 1 3X /G 05 1 4X/ G0 5 1 4 X3 Ex treme Series B andsaw Bl ade Cha n ges T o r emove a blad e : 1. DISCONNECT BANDSAW FROM POWER! 2. Release the blade tension by turning the blade tension quick release lever to the left. 3. Remove the table insert and the table pin. Adjust the upper and lower guide bearings as far away as possible from the [...]
-
Seite 53
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -43 - SE CTION 5 : A CC E SSORIE S Replacement Blades These replacement blades are milled for exact tooth set and are made with high quality tool steel. 131 1 ⁄ 2 " Carbon Steel Replacement Blades for the Model G0513X MODEL WIDTH TPI H4803 1/8" 14 RAKER H4804 1/4" 6 HOO[...]
-
Seite 54
- 44 - G0 5 1 3X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series Band saw Figure 53. Our most popular safety glasses. G7984—Face Shield H1298—Dust Sealed Safety Glasses H1300—UV Blocking, Clear Safety Glasses H2347—Uvex ® Spitfire Safety Glasses H0736—Shop Fox ® Safety Glasses Safety Glasses are essential to every shop. If you already have [...]
-
Seite 55
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -45 - SE CTION 6 : MAINT EN AN CE Alwa ys disconnect power to t he ma ch in e b e fo re per forming maintenanc e. Failure to do t his may result in serious pe rson - al injury . Sealed and pre-lubric ated ball bearings require no lubrication for the life of the bearings. All bear - ings[...]
-
Seite 56
- 46 - G0 5 1 3X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw This sec tion is provided for your c onv enience — it is not a substitute for the Grizzly Ser vic e De part ment. If you need help troub leshooting, you need replacement par ts, or you are unsure of how to per form the pro - cedures in this se ction, then feel free to call our [...]
-
Seite 57
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 4 7 - Symptom Possible Cause Possible Solution M a c h i n e h a s v i b r a t i o n o r noi sy oper atio n when r unn ing. 1. Blade weld hits guides or teeth are broken. 2. Bent or worn out blade. 3. Motor or component is loose. 4. V-belt worn or loose. 5. Motor fan is rubbing on fan[...]
-
Seite 58
- 48 - G0 5 1 3X / G05 1 4X / G05 1 4X 3 E x treme Series Bandsaw Chec ki n g V - Belt T o ensure optimum power transmission from t he motor to the blade, the V-belt must be in g ood conditio n and operate under proper tension. The belt should be chec ked for cracks, fra ying, and wea r . Belt tension should be chec ked at least ev ery 3 months— [...]
-
Seite 59
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -49 - Repl ac i ng V - Bel t T ools N e ede d : QTY Hex Wrench 6 mm ............................................... 1 W rench 1 3 mm .................................................... 1 T o r eplace the V-be lt : 1. DISCONNECT BANDSAW FROM POWER! 2. Open both wheel covers, and remove [...]
-
Seite 60
-50 - G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series Band saw Figure 61. The wheel brush. Wheel Brush Adjustment Screw Wheel Shaft Hinge Figure 60. Tension lever adjustment components. Adjustment Gap 1 ⁄ 16 "- 3 ⁄ 16 " A dju s ti n g T ens i on Le v er The tension leve r has an adjustment screw that allows you to adjust how muc[...]
-
Seite 61
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 5 1 - Wheel Al ign men t Figure 62. Dimensions of coplanarity gauge. Compone nts and H ardware Ne ede d : Qt y 60" Long 2x4 ..................................................... 1 Tools Needed: Wrench 13mm ................................................... 1 Tape Measure .......[...]
-
Seite 62
-52- G05 1 3X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw 5. Adjust the tracking knob to get both wheels parallel. If the wheels won’t go parallel to each other, then move the lower wheel at the adjustment hub ( Figure 64 ) so they line up. 6. If the wheels will go parallel but not coplanar, shim the required wheel out as necessary, usin[...]
-
Seite 63
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -53 - G0 5 1 3 X Electr ic al Com pon en ts Sw it ch W iri ng Mo to r Wi rin g To Power Supply To Motor[...]
-
Seite 64
-5 4 - G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw G0 5 1 3 X Wir in g Dia gr am G0513X Wiring Diagram [...]
-
Seite 65
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -55 - G0 5 1 4 X Electr ical Com po nen ts Po we r Sup pl y Jun ct io n Blo ck Mo to r Wi rin g Co nt rol Pan el Wiri ng Ma gn eti c Swi tc h Wi ri ng To Motor To Junction Box To Control Panel POWER ON OFF[...]
-
Seite 66
-56 - G05 1 3 X / G05 1 4X / G05 1 4X 3 E x treme Series Bandsaw G0 5 1 4 X Wi r i n g Diag ra m ?[...]
-
Seite 67
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -57 - G0 5 1 4 X3 E lectr ica l Com ponen ts Mo to r Wir ing (220 V) Co nt rol Pan el Wiri ng POWER ON OFF Ma gn eti c Swi tc h Wi ri ng To Motor To Junction Box To Control Panel Po we r Sup pl y Jun ct io n Blo ck[...]
-
Seite 68
-58 - G 05 1 3 X / G05 1 4 X /G 05 1 4X 3 E x treme Series Bandsaw G0 5 1 4 X3 Wi ri n g Dia gra m [...]
-
Seite 69
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -59 - ?[...]
-
Seite 70
- 60 - G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series Band saw ?[...]
-
Seite 71
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 6 1 - REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0513X001 BUSHING 54 PCB23M CARRIAGE BOLT M8-1.25 X 80 2 PSS01M SET SCREW M6-1 X 10 55 P0513055 UPPER WHEEL COVER 3 P0513X003 BUSHING 56 PB10M HEX BOLT M6-1 X 25 4 P0513004 LIFTING EYE BOLT M10-1.5 57 PW03M FLAT WASHER 6MM 5 P05130[...]
-
Seite 72
- 62- G05 1 3X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw REF PART # DESCRIPTION REF PART # DESCRIPTION 99 PN02M HEX NUT M10-1.5 121-29 PH7587029 SPACER PLATE 100 P0513100 SMALL GEAR 122 P0513X122 GEAR 101 P0513X101 LOCK HANDLE 123 P0513X123 FIXED BOLT 102 P0513102 TRUNNION SUPPORT BRACKET 124 P0513X124 COVER 103 PLW06M LOCK WASHER 10MM 1[...]
-
Seite 73
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -63 - G0 5 1 3 X L abels Safety labels warn about machine hazards and ways to prevent injury. The owner of this machi[...]
-
Seite 74
- 64 - G0 5 1 3X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw [...]
-
Seite 75
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -65 - [...]
-
Seite 76
- 66 - G05 1 3X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw G0 5 1 4 X / G 0 5 1 4 X3 L abels Safety labels warn about machine hazards and ways to prevent injury. The owne[...]
-
Seite 77
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw - 67 - REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSS01M SET SCREW M6-1 X 10 49 PSB04M CAP SCREW M6-1 X 10 2 PFS07M FLANGE SCREW M5-.8 X 10 50 P0513050 CLEAR WINDOW 3 P0513X003 BUSHING 51 PSB02M CAP SCREW M6-1 X 20 4 P0513004 LIFTING EYE BOLT M10-1.5 52 P0514X052 BUSHING 5 P0514005[...]
-
Seite 78
- 68 - G0 5 1 3X / G0 5 1 4 X / G0 5 1 4 X3 Ex treme Series Band saw REF PART # DESCRIPTION REF PART # DESCRIPTION 83 PB32M HEX BOLT M10-1.5 X 25 125-3 PH7587003 FIXED SHAFT 84 PLW06M LOCK WASHER 10MM 125-4 PH7587004 SHAFT 85 P0513085 MOTOR BRACKET 125-5 PH7587005 SPRING PIECE 86 PSBS01M BUTTON HD CAP SCR M8-1.25 X 20 125-6 PH7528004 ADJUSTMENT HAN[...]
-
Seite 79
G05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series B andsaw -69 - REF PART # DESCRIPTION REF PART # DESCRIPTION 144 PSB02M CAP SCREW M6-1 X 20 158 PN04M HEX NUT M4-.7 145 P0514X145 LOCATE BUSHING 159 PS23M PHLP HD SCR M5-.8 X 12 146 P0513X130 BUSHING 160 P0514X160 STRAIN RELIEF 20MM 147 PSBS01M BUTTON HD CAP SCR M8-1.25 X 20 161 P0514X161 MAG SW[...]
-
Seite 80
- 70- G 05 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 Ex treme Series Band saw Grizzly Industrial, Inc. warrants ev ery prod uct it sells for a period of 1 year to the original purchaser from the date of purchase. This warran t y does not apply to defects d ue directly or indirectly to misuse, abuse, negligence, accid ents, repairs or alterations or lack of[...]
-
Seite 81
?[...]
-
Seite 82
?[...]
-
Seite 83
[...]
-
Seite 84
B uy Dir ect and S ave with Gr izzl y ® – T r usted, Pr oven and a Gr eat V alue ! ~Since 1983~ ORDER 24 HOURS A DA Y! 1-800-523-4777 Visit Our Website Today For Current Specials![...]