Grizzly G0514X Bedienungsanleitung
- Schauen Sie die Anleitung online durch oderladen Sie diese herunter
- 76 Seiten
- 11.83 mb
Zur Seite of
Ähnliche Gebrauchsanleitungen
-
Saw
Grizzly G1023
37 Seiten 1.36 mb -
Saw
Grizzly G0682
48 Seiten 2.48 mb -
Saw
Grizzly G0696X1-97X
12 Seiten 0.97 mb -
Saw
Grizzly Model
59 Seiten 8.12 mb -
Saw
Grizzly G1019Z
44 Seiten 1.72 mb -
Saw
Grizzly G0511
56 Seiten 3.84 mb -
Saw
Grizzly G0588/G0591
76 Seiten 13.72 mb -
Saw
Grizzly G3104
2 Seiten 0.04 mb
Richtige Gebrauchsanleitung
Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Grizzly G0514X an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Grizzly G0514X, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.
Was ist eine Gebrauchsanleitung?
Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Grizzly G0514X die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.
Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Grizzly G0514X. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.
Was sollte also eine ideale Gebrauchsanleitung beinhalten?
Die Gebrauchsanleitung Grizzly G0514X sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Grizzly G0514X
- Den Namen des Produzenten und das Produktionsjahr des Geräts Grizzly G0514X
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Grizzly G0514X
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen
Warum lesen wir keine Gebrauchsanleitungen?
Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Grizzly G0514X zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Grizzly G0514X und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Grizzly finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Grizzly G0514X zu überspringen, wie es bei der Papierform passiert.
Warum sollte man Gebrauchsanleitungen lesen?
In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Grizzly G0514X, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.
Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Grizzly G0514X widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.
Inhaltsverzeichnis der Gebrauchsanleitungen
-
Seite 1
MO DE L G0 5 1 3 X / G0 5 1 4 X / G0 5 1 4 X 3 E X TR EME S E RIE S B AND S A W O WNER'S MANU AL COPYRIGHT © JANUAR Y , 2 00 6 BY GRIZ ZL Y IN DUSTRIAL , I NC. RE VISED FEBRUAR Y , 20 07 ( TR) W ARN I NG : N O POR TI ON OF TH I S M AN UAL M A Y BE REPR ODU CED I N A NY SH APE OR FORM W IT HOU T THE W RI T TE N A PPROV A L O F G RI Z ZL Y I ND[...]
-
Seite 2
?[...]
-
Seite 3
T able o f Co n ten ts INTRODUCTION ............................................................................................................................... 3 Foreword .................................................................................................................................... 3 Contact Info ...........................[...]
-
Seite 4
SECTION 5: ACCESSORIES ......................................................................................................... 43 SECTION 6: MAINTENANCE ........................................................................................................ 45 Schedule ..............................................................................[...]
-
Seite 5
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -3 - If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C / O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 We stand behind our machines. If you have any service questions or parts requests, please call [...]
-
Seite 6
- 4- G0 5 1 3X /G 05 1 4 X / G05 1 4X 3 Ex treme Series Band saw The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model G0513X MACHINE DATA SHEET Custom[...]
-
Seite 7
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -5 - The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 2 Model G0513X Table Information Table Len[...]
-
Seite 8
- 6 - G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw G0 5 1 4 X Mac h in e Data Sheet The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model [...]
-
Seite 9
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 7 - The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 2 Model G0514X Table Information Table Le[...]
-
Seite 10
-8- G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model G0514X3 MACHINE DATA SHEET Customer[...]
-
Seite 11
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -9 - The information contained herein is deemed accurate as of 2/9/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 2 Model G0514X3 Table Information Table Le[...]
-
Seite 12
- 1 0 - G0 5 1 3X /G 05 1 4 X / G05 1 4X 3 Ex treme Series Band saw Figure 2. Bandsaw back view. A. Tension Indicator Window B. ON/OFF Switch C. Rip Fence D. Fence Locking Lever E. Dust Port 4" F. Miter Gauge G. Blade Tension Handwheel H. Ball Bearing Roller Guides I. Guide Post J. Guide Post Handwheel K. Blade Tracking Window Identi f ica tio[...]
-
Seite 13
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 1 1 - 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5. WEAR PROPER APPAREL. D O NOT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to con - tain lo[...]
-
Seite 14
- 1 2- G05 1 3X /G 05 1 4 X / G05 1 4X 3 Ex treme Series Band saw 7. ONLY ALLOW TRAINED AND PROP- ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe dis- tance from the work area. 9. MAKE WORKSHOP CHILD PROOF. Use[...]
-
Seite 15
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 1 3 - A ddit io nal Safety Instr uctio ns fo r Ban dsa ws 7. BLADE SPEED. Allow blade to reach full speed before cutting. 8. LEAVING WORK AREA. Never leave a machine running and unattended. Allow the bandsaw to come to a complete stop be - fore you leave it unattended. 9. FEED RATE. Always[...]
-
Seite 16
- 1 4 - G0 5 1 3X /G0 5 1 4 X / G05 1 4X 3 E x treme Series Band saw Serious person al injur y c ould occur if y ou connect the machine to the po wer source before y ou have comple ted th e set up pro - cess . DO NOT conne ct th e machine to the power source until instructed to do so. Operati on S E C T I O N 2 : C I R C U I T R E Q U I R E M E N T[...]
-
Seite 17
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 1 5 - In t he even t of an electric al s hort , grounding reduces the risk of electric sho ck. The grounding wire in t he power cord must be properly connect - ed to t he grounding prong on the p lug; lik ewise , the outlet must be properly installed and ground - ed. All elec trical connec[...]
-
Seite 18
- 1 6 - G0 5 1 3X /G0 5 1 4 X / G05 1 4X 3 E x treme Series Bands aw The Model G 05 1 3X / G05 1 4X/ G05 1 4X 3 was care - fully packed when it left our wareh ouse. If you dis cover t he ma chine is d amaged af ter you ha ve sig ned for deliver y , please immed iately c all Customer Service at ( 5 7 0 ) 5 46 - 96 63 for advice. Sav e the containers[...]
-
Seite 19
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 1 7 - In v ent ory After all the parts hav e been remov ed from the crate , you should hav e the following items: Crate Content s ( Figure 7 & 8 ): Qt y A . Bandsaw (not shown) ................................. 1 B. T able ........................................................... 1 C[...]
-
Seite 20
- 1 8 - G05 1 3 X / G05 1 4X /G0 5 1 4 X 3 Ex treme Series Bandsaw Hard w are Recog n iti on Chart[...]
-
Seite 21
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 1 9 - Figure 9. G05 1 3 X minimum working c learances. Fl oor Lo ad Refe r to t he Machine Dat a She et for the weight and foot print s peci ficati ons of y our mac hine. Some floors ma y requi re additional reinf orcement to sup por t both the machine and operator . Wo rki ng Cl ear an ce[...]
-
Seite 22
-20- G 05 1 3X / G05 1 4X/ G0 5 1 4 X 3 Ex treme Series Bandsaw Mo vi n g & P lac i ng Ba se Un it Figure 11. Lifting the bandsaw. This is an extr emely heavy machi ne. Serious per sonal injury may occur if safe moving methods are not fol lowed. T o be safe, y ou will ne ed assistanc e and a forklif t or a hoist when removing the mac hine from [...]
-
Seite 23
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 21 - Figure 14. Quick release tension lever. Tighten Loosen 2. Adjust the upper and lower blade guides away from the blade. Refer to Adjusting Blade Guide Bearings on Page 29 for more details. 3. Open the upper and lower wheel covers, and slide the blade off of both wheels. All saw blades [...]
-
Seite 24
-22- G05 1 3X /G0 5 1 4 X / G05 1 4X 3 E x treme Series Bands aw Bl ade T ra cki n g Personal injury or death can occur if the machine starts while your hand is touching the bandsaw wheel during tracking adjustments. Disconnect power from the bandsaw before performing blade tracking adjustments. The blade tracking is primarily affected by the tilt [...]
-
Seite 25
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -23- The positive stop allo ws the table to be quickly and acc urat ely re turned to the horizontal (0˚) position af ter being adjusted to a dif ferent angle. Compone nts and Hardwar e Ne eded : Qt y Hex Bolt M8-1.25 x 90 ....................................... 1 Hex Nut M8-1.25 ...........[...]
-
Seite 26
-2 4- G0 5 1 3X /G 05 1 4 X / G05 1 4X 3 E x treme Series Band saw Figure 20. Squaring table to blade. 5. Adjust the positive stop bolt to the table and secure it by tightening the hex nut against the trunnion bracket. 6. Check the adjustment for accuracy once you have tightened the hex nut. 7. Loosen the screw on the pointer, but do not remove it.[...]
-
Seite 27
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -25- 3. Install an M8-1.25 hex nut on the fence handle, then thread the handle into the fence assembly ( Figure 23 ). Tighten the hex nut against the fence pivot block to secure the handle. Figure 23. Handle installed on fence assembly. Hex Nut Pivot Block 4. Thread the M6-1 hex nut onto the[...]
-
Seite 28
-26- G0 5 1 3X /G 05 1 4 X / G05 1 4X 3 Ex treme Series Band saw 7. Tighten the lock handle. 8. Pull the fence handle up and place the fence assembly on the fixed rail as shown in Figure 26 . Figure 26. Correctly installed fence. 6. Slide the resaw fence over the moving plate, as shown in Figure 25 , so the moving plate fits inside the channel of t[...]
-
Seite 29
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 27 - T ens io ni n g Bla de A properly tensioned blade is essential for mak - ing accurate cuts a nd is required be fore mak - ing man y bandsaw adjustments. ( E ve r y time you replace the blade, y ou should perform this proce - dure be cause all blades tension dif ferently . ) To tension[...]
-
Seite 30
-28- G05 1 3X/ G0 5 1 4 X /G 05 1 4 X3 E xtreme Series Bandsaw 5. Tighten the assembly cap screw. 6. Loosen the cap screw on the support bearing adjustment shaft. 7. Place a 0.016" feeler gauge between the support bearing and the blade, and position the bearing 0.016" away from the back of the blade as illustrated in Figure 29 . Figure 28[...]
-
Seite 31
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -29- The blade guides provide side -to- side sup por t to help keep the blade straight while cut ting. The blade guid es are d esigned to be adjusted in t wo wa ys— for ward /back ward and si de-to -side. To adjust the upper and lower blade guides : 1. Make sure the blade is tracking prope[...]
-
Seite 32
-3 0 - G05 1 3 X / G05 1 4X /G0 5 1 4 X 3 Ex treme Series Bandsaw NOTICE Make sure that the blade teeth will not con- tact the guide bearings when the blade is against the rear support bearing during the cut or the blade teeth will be ruined. 5. Tighten the cap screw on the lateral adjust- ment rod. 6. Loosen the bearing rotation adjustment cap scr[...]
-
Seite 33
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -3 1 - T o ensur e cutting accuracy when the f ence is fi rst installed, the fence should be aligned with the miter slot. To align the fence parallel with the miter slot: 1. If the fence is mounted on the left-hand side of the blade, remove it and remount it next to the miter slot. 2. Loosen[...]
-
Seite 34
-32- G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw Damag e to your eyes, lungs, and ears could re su lt fro m usi ng th is ma chi ne wi th out prope r protective ge ar . Alway s wear safet y glasses , a resp irator , and hearing protection when op erating this machine. Lo o s e h ai r a nd cl o th - ing could get caught in machiner y a [...]
-
Seite 35
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -33 - Guide Post Lock Knob Guide Post Handwheel The ST ART / ST OP switch on the Model G0 5 1 3X / G05 1 4X/ G0 5 1 4 X 3 is loc ated on t he column for easy acces s ( Figur es 3 7 & 3 8 ). Immediately turn the machine OFF if there bec omes a safety hazard. ST ART / ST OP Swi tc h Figure[...]
-
Seite 36
-3 4- G0 5 1 3X /G0 5 1 4 X / G05 1 4X 3 Ex treme Series Band saw Bl ade Lead Bandsaw blades commonly wander of f the cut line when sawing, as shown in Figure 4 1 . T his is called blade lead. B lade lead is co mmonly caused b y too fast of a feed rate , a dull or abused blade, or improper tension. If y our blade is sharp / undamaged and you still [...]
-
Seite 37
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -35 - 3. Clamp the board to the bandsaw table with- out moving it. Now slide the fence over to the board so it barely touches one end of the board. 4. Loosen the four cap screws on top of the fence. 5. Skew the fence so it is parallel to the edge of the scrap piece. You may need to re-adjust[...]
-
Seite 38
-3 6- G 05 1 3X / G05 1 4X/ G0 5 1 4 X 3 Ex treme Series Bandsaw Cr oss cu t ti n g Crosscut ting is the proces s of cut ting across the grain of wood. For ply wood and other processed wood, crosscut ting simply means cut ting across the width of the material . T o make a 9 0˚ cro sscut : 1. Mark the workpiece on the edge where you want to begin t[...]
-
Seite 39
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -37 - Figure 45. Resawing lumber. Resawing ( Figure 4 5 ) is the process of cut ting a board into two or more t hinner boards. The ma xi - mum boa rd width that can be resa wn is limited b y the maximum cut ting height of the bandsaw . One of the most impor tant considerations when resawing [...]
-
Seite 40
-3 8- G0 5 1 3X /G 05 1 4 X / G05 1 4X 3 Ex treme Series Band saw Stac k ed Cuts One of t he benefits of a band saw is it s abilit y to cut multiple copies of a pa r ticular shape b y stack - ing a number of workpieces together . B efo re mak - ing stacked cuts, ensure that both the table and the blade are properly adjusted to 90° . Other wise, an[...]
-
Seite 41
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -39 - Bl ade Sp eed The blade speed can b e adjusted to 1 700 or 350 0 FP M. Sp eed adjustments are made by moving the V - belt position on the motor and wheel pul - ley s. Most woodcut ting c an be per formed suc cessfully at the higher blade speeds. Slower blade s peeds generally produce b[...]
-
Seite 42
- 40 - G0 5 1 3X /G0 5 1 4 X / G05 1 4X 3 E x treme Series Bands aw Bl ade Inf orma ti on Selecting the rig ht blade requires a k nowledge of the various blade characteristic s to match the blade with the par ticular cut ting operation. Bl ade Le ng th Measured by the circumf erence, bl ade lengths are usually unique to the brand of your bandsaw an[...]
-
Seite 43
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 4 1 - • Hook : The teeth on this style have a posi- tive angle (downward) which makes them dig into the material, and the gullets are usu - ally rounded for easier waste removal. These blades are excellent for the tough demands of resawing and ripping thick material. To oth Pi tc h Usual[...]
-
Seite 44
- 42 - G05 1 3X/ G0 5 1 4 X /G 05 1 4 X3 E xtreme Series Bandsaw Bl ade Chan g es T o r emov e a blade : 1. DISCONNECT BANDSAW FROM POWER! 2. Release the blade tension by turning the blade tension quick release lever to the left. 3. Remove the table insert and the table pin. Adjust the upper and lower guide bearings as far away as possible from the[...]
-
Seite 45
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -43 - SE CTION 5 : A CCE SSO RIE S Replacement Blades These replacement blades are milled for exact tooth set and are made with high quality tool steel. 131 1 ⁄ 2 " Carbon Steel Replacement Blades for the Model G0513X MODEL WIDTH TPI H4803 1/8" 14 RAKER H4804 1/4" 6 HOOK H48[...]
-
Seite 46
- 44 - G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw Figure 53. Our most popular safety glasses. G7984—Face Shield H1298—Dust Sealed Safety Glasses H1300—UV Blocking, Clear Safety Glasses H2347—Uvex ® Spitfire Safety Glasses H0736—Shop Fox ® Safety Glasses Safety Glasses are essential to every shop. If you already have a pai[...]
-
Seite 47
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -45 - SE CTION 6 : MAINT ENA NC E Alwa ys disconn ect power to th e ma ch ine b e fo re per forming maintenance. Failure to do t his may result in se rious p erson - al injury . Sealed and pre-lubric ated ball bearings require no lubrication for the life of the bearings. All bear - ings are [...]
-
Seite 48
- 46 - G05 1 3X/ G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw This sec tion is provided for your c onv enience — it is not a substitute for the Grizzly Ser vice Depar tment. If you need help troubleshooting, you need replacement par ts, or you are unsure of how to per form t he pro - cedures in this section, then feel free to call our T echnic a[...]
-
Seite 49
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 4 7 - Symptom Possible Cause Possible Solution M a c h i n e h a s v i b r a t i o n o r noi sy op erati on when r unnin g. 1. Blade weld hits guides or teeth are broken. 2. Bent or worn out blade. 3. Motor or component is loose. 4. V-belt worn or loose. 5. Motor fan is rubbing on fan cove[...]
-
Seite 50
- 48 - G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw Chec ki n g V - Belt T o ensure optimum power transmission from the motor to the blade , the V - belt must be in good conditio n and operate und er proper tension. The belt s hould be checked for cracks, fra ying, and wea r . Belt tension should be c hecked at least ev ery 3 months ?[...]
-
Seite 51
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -49 - Repl ac in g V - Belt T ools N ee ded : QT Y Hex Wrench 6 mm ............................................... 1 W rench 1 3 mm .................................................... 1 T o r eplace th e V - belt : 1. DISCONNECT BANDSAW FROM POWER! 2. Open both wheel covers, and remove the [...]
-
Seite 52
-50 - G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw Figure 61. The wheel brush. Wheel Brush Adjustment Screw Wheel Shaft Hinge Figure 60. Tension lever adjustment components. Adjustment Gap 1 ⁄ 16 "- 3 ⁄ 16 " A dju st in g T ensi on Le v er The tension leve r has an adjustment screw that allows you to adjust how much tensi[...]
-
Seite 53
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 5 1 - Wheel Al ign men t Figure 62. Dimensions of coplanarity gauge. Compone nts and Hardwar e Ne eded : Qt y 60" Long 2x4 ..................................................... 1 Tools Needed: Wrench 13mm ................................................... 1 Tape Measure .............[...]
-
Seite 54
-52- G05 1 3X / G05 1 4X/ G0 5 1 4 X 3 Ex treme Series Bandsaw 5. Adjust the tracking knob to get both wheels parallel. If the wheels won’t go parallel to each other, then move the lower wheel at the adjustment hub ( Figure 64 ) so they line up. 6. If the wheels will go parallel but not coplanar, shim the required wheel out as necessary, using th[...]
-
Seite 55
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -53 - G0 5 1 3 X Electr ical Compo nen ts Sw itc h Wi rin g Mo tor Wir ing To Power Supply To Motor[...]
-
Seite 56
-5 4- G0 5 1 3X /G 05 1 4 X / G05 1 4X 3 Ex treme Series Band saw G0 5 1 3 X Wi r in g Dia gra m G0513X Wiring Diagram [...]
-
Seite 57
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -55 - G0 5 1 4 X Electr ical Compo nen ts Po wer Supp ly Ju nc tio n Blo ck Mo tor Wir ing Co ntr ol Pa ne l Wir ing Ma gne ti c Swit ch Wi rin g To Motor To Junction Box To Control Panel POWER ON OFF[...]
-
Seite 58
-56 - G 05 1 3X / G05 1 4X/ G05 1 4X 3 Ex treme Series Band saw G0 5 1 4 X Wi r in g Dia gra m ?[...]
-
Seite 59
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -57 - G0 5 1 4 X 3 Electr ical Compo nen ts Mo tor Wi ri ng (22 0V ) Co ntr ol Pa ne l Wir ing POWER ON OFF Ma gne ti c Swit ch Wi rin g To Motor To Junction Box To Control Panel Po wer Supp ly Ju nc tio n Blo ck[...]
-
Seite 60
-58 - G0 5 1 3X /G 05 1 4 X / G05 1 4X 3 E x treme Series Band saw G0 5 1 4 X 3 Wi r in g Dia gra m ?[...]
-
Seite 61
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -59 - [...]
-
Seite 62
- 60 - G0 5 1 3X / G05 1 4 X / G0 5 1 4 X 3 Ex treme Series Bandsaw [...]
-
Seite 63
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 6 1 - REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0513X001 BUSHING 54 PCB23M CARRIAGE BOLT M8-1.25 X 80 2 PSS01M SET SCREW M6-1 X 10 55 P0513055 UPPER WHEEL COVER 3 P0513X003 BUSHING 56 PB10M HEX BOLT M6-1 X 25 4 P0513004 LIFTING EYE BOLT M10-1.5 57 PW03M FLAT WASHER 6MM 5 P0513005 MA[...]
-
Seite 64
- 62- G05 1 3X /G 05 1 4 X / G05 1 4X 3 Ex treme Series Band saw REF PART # DESCRIPTION REF PART # DESCRIPTION 99 PN02M HEX NUT M10-1.5 121-29 PH7587029 SPACER PLATE 100 P0513100 SMALL GEAR 122 P0513X122 GEAR 101 P0513X101 LOCK HANDLE 123 P0513X123 FIXED BOLT 102 P0513102 TRUNNION SUPPORT BRACKET 124 P0513X124 COVER 103 PLW06M LOCK WASHER 10MM 125 [...]
-
Seite 65
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -63 - G0 5 1 3 X Lab el s Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine M[...]
-
Seite 66
- 64 - G05 1 3 X / G0 5 1 4 X /G 05 1 4 X3 E xtreme Series Bandsaw [...]
-
Seite 67
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -65 - ?[...]
-
Seite 68
- 66 - G0 5 1 3X /G0 5 1 4 X / G05 1 4X 3 Ex treme Series Band saw G0 5 1 4 X / G0 5 1 4 X 3 L abels Safety labels warn about machine hazards and ways to prevent injury. The owner [...]
-
Seite 69
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw - 67 - REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSS01M SET SCREW M6-1 X 10 49 PSB04M CAP SCREW M6-1 X 10 2 PFS07M FLANGE SCREW M5-.8 X 10 50 P0513050 CLEAR WINDOW 3 P0513X003 BUSHING 51 PSB02M CAP SCREW M6-1 X 20 4 P0513004 LIFTING EYE BOLT M10-1.5 52 P0514X052 BUSHING 5 P0514005 MACH[...]
-
Seite 70
- 68 - G05 1 3X/ G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw REF PART # DESCRIPTION REF PART # DESCRIPTION 83 PB32M HEX BOLT M10-1.5 X 25 125-3 PH7587003 FIXED SHAFT 84 PLW06M LOCK WASHER 10MM 125-4 PH7587004 SHAFT 85 P0513085 MOTOR BRACKET 125-5 PH7587005 SPRING PIECE 86 PSBS01M BUTTON HD CAP SCR M8-1.25 X 20 125-6 PH7528004 ADJUSTMENT HANDLE M8[...]
-
Seite 71
G05 1 3 X / G05 1 4X /G0 5 1 4 X3 Ex treme Series Bandsaw -69 - REF PART # DESCRIPTION REF PART # DESCRIPTION 144 PSB02M CAP SCREW M6-1 X 20 158 PN04M HEX NUT M4-.7 145 P0514X145 LOCATE BUSHING 159 PS23M PHLP HD SCR M5-.8 X 12 146 P0513X130 BUSHING 160 P0514X160 STRAIN RELIEF 20MM 147 PSBS01M BUTTON HD CAP SCR M8-1.25 X 20 161 P0514X161 MAG SWITCH [...]
-
Seite 72
- 70- G 05 1 3X / G05 1 4X/ G0 5 1 4 X 3 Ex treme Series Bandsaw Grizzly Industrial, Inc. warrants every produ ct it sells for a p eriod of 1 year to the original purchaser from the date of purchase. This warranty do es not apply to d ef ect s due direct ly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mai[...]
-
Seite 73
?[...]
-
Seite 74
[...]
-
Seite 75
[...]
-
Seite 76
[...]