Grizzly H6155 Bedienungsanleitung

COPYRIGHT © JULY, 2004 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #EW6394 PRINTED IN CHINA R O T A R Y M I N I G R I N D E R W I T H F L E X S H A F T MODEL H6155 INSTRUCTION MANUAL[...]

WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonr[...]

-1 - For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described bel[...]

Model H6155 Rotary Mini Grinder -2 - 9. US E PR OPE R E XT EN SI ON COR D for t he t ool. Make sure your ex ten- sio n cor d is in go od co ndi tio n. Con - du ctor s ize shoul d be in ac cor dan ce wit h th e ch ar t bel ow. The a mper age rat ing s houl d be l isted on t he m otor or to ol nam epl ate. An un der sized cor d will cau se a drop in [...]

Model H6155 Rotary Mini Grinder -3 - Operating this mini grinder can propel objects into the air, causing immedi- ate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. No list of safety guidelines can be complete. Every shop environment is [...]

Model H6155 Rotary Mini Grinder -4 - -4 - INTRODUCTION If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call[...]

Model H6155 Rotary Mini Grinder -5 - -5 - INVENTORY Figure 1. Model H6155 features and controls. The set up and operation instructions will be easier to understand if you are familiar with the components of the Model H6155 Rotary Mini Grinder. Match up the feature list below with the letters in Figure 1 to identify the feature locations. A . T ool [...]

Model H6155 Rotary Mini Grinder -6 - OPERATIONS Using The Grinder The Model H6155 is best suited for high RPM, low torque applications. Most opera- tions performed with the grinder will per- form best at higher RPM settings; how- ever, slower RPM settings are ideal when working with plastics that melt easily. Always test the bit and RPM combination[...]

Model H6155 Rotary Mini Grinder -7 - Use low RPM settings when work- ing with plastics or other materi - als with low melting points. Melted plastics can liquefy, be thrown into the air, and stick to the operator, causing serious personal injury. High RPM Uses High RPM's are best for general carving, cutting, routing, and grinding. The grinder[...]

Model H6155 Rotary Mini Grinder -8 - Installing the Router Base The route r bas e tra nsfo rms t he m ini g rin d- er int o a m ini ro uter. It c an be u sed w ith Griz zly 's mi ni r outer bi ts to ro und ove r cor ner s or ap ply pro file s to th e ed ges of your wo rkp iec e. It ca n a lso be u sed w ith the i ncl ude d to ol bi ts to mil l[...]

Model H6155 Rotary Mini Grinder -9 - MAINTENANCE Carbon Brush Replacement Carbon brush life is 500–2000 hours, depending on the type of use. Always replace both brushes at the same time. To replace the carbon brushes: 1. Use a small screwdriver to remove the caps shown in Figure 6 fro m the sides of the motor housing. Be careful when removing the[...]

Model H6155 Rotary Mini Grinder -10 - H6155 Rotary Mini Grinder Parts Breakdown REF PART # DESCRIPTION 1 PH6155001 1/8" COLLET 2 PH6155002 3/32" COLLET 3 PH6155003 COLLET NUT 4 PH6155004 COLLET SHIELD 5 PH6155005 HANGER 6 PH6155006 PLUG AND CORD 7 PH6155007 BRUSH CAP 8 PH6155008 CARBON BRUSH 9 PH6155009 VARIABLE SPEED LEVER 10 PH6155010 C[...]

Model H6155 Rotary Mini Grinder -11 - REF PART # DESCRIPTION 22 PH6155022 FLEX SHAFT 23 PH6155023 INNER SPINDLE 24 PH6155024 SANDING ASSORTMENT BAG 25 PH6155025 TOOL BIT ASSORTMENT BAG 26 PH6155026 CLAMP BASE 27 PH6155027 TELESCOPING TOOL HOLDER 28 PH6155028 TOOL BAG 29 PH6155029 FLASHLIGHT BASE 30 PH6155030 ROUTER BASE 31 PH6155031 FLEX SHAFT COLL[...]

Model H6155 Rotary Mini Grinder -12 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole[...]

Name ________________________________________________________________ Street _________________________________________________________ City ____________________ State ________ Zip ________________________ Phone Number ____________ E-Mail ___________________ Serial # _________ Model # _______________Serial#________________ Order # _____________ The [...]

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here[...]