GTO Mighty Mule 352 Bedienungsanleitung

© 2008 GTO , Inc. R352INST rev - 08/08/08 Installation Manual for the This product meets and exceeds the requirements of UL 325, the standard which regulates gate opener safety , as established and made effective March 1, 2000, by Underwriters Laboratories Inc. W ARNING! This equipment is similar to other gate or door equipment and meets or exceed[...]

VEHICULAR GA TE OPENER CLAS S CA TEGORIES Residential V ehicular Gate Opener-Class I: A vehicular gate opener (or system) intended for use in a home of one-to-four single family dwelling, or a garage or parking area associated therewith. Commercial/General Access V ehicular Gate Opener-Class II: A vehicular gate opener (or system) intended for use [...]

Gate Opener Class Categories ------------------------------------------------------------ inside cover Units and Standards Conversion Chart ------------------------------------------------ inside cover PLEASE READ THIS FIRST! ------------------------------------------------- page iii Important Safety Instructions -----------------------------------[...]

PLEASE READ THIS FIRST! iii BEFORE YOU BEGIN TO INST ALL YOUR A UTOMA TIC GA TE OPENER: watch the enclosed video and read these instructions carefully and completely to become familiar with all parts and installation steps. The video is only designed as an overview of the installation procedure. Y ou must read the installation manual for detailed i[...]

IMPORT ANT SAFETY INSTRUCTIONS Mighty Mule 352 1 Because automatic gate openers produce high levels of force, consumers need to know the potential hazards associated with improperly designed, installed, and maintained automated gate opener systems. Keep in mind that the gate opener is just one component of the total gate operating system. Each comp[...]

IMPORT ANT SAFETY INSTRUCTIONS 2 Mighty Mule 352 F or The Consumer W ARNING: T o reduce the risk of injury or death: 1. READ AND FOLL OW ALL INSTRUCTIONS. Failure to meet the requirements set forth in the instruction manual could cause severe injury and/or death, for which the manufacturer cannot be held responsible. 2. When designing a system that[...]

IMPORT ANT SAFETY INSTRUCTIONS Mighty Mule 352 3 Moving Gate Area Moving Gate Area Driveway 10' 10' 10' 10' 10' 10' NEVER INST ALL any control device within gray area Entrapment Zones for a proper Pull- T o-Open installation: Zone 1 – leading edge of the master and second gate. Zone 2 – between the gate and the gat[...]

IMPORT ANT SAFETY INSTRUCTIONS 4 Mighty Mule 352 III. After Installation 1. Attach the warning signs (included) to each side of the gate to alert the public of auto matic gate operation. It is your responsibility to post warning signs on both sides of your gate. If any of these signs or warning decals become damaged, illegible or missing, replace t[...]

IMPORT ANT SAFETY INSTRUCTIONS Mighty Mule 352 5 ENTRAPMENT ALARM (UL 325; 30A .1.1A) The Mighty Mule® 352 Gate Opener is designed to stop and reverse within 2 seconds when the gate comes in contact with an obstruction. Additionally , these openers are equipped with an audio entrapment alarm which will activate if the unit obstructs twice while op[...]

IMPORT ANT SAFETY INSTRUCTIONS 6 Mighty Mule 352 Install W arning Signs Entrapment Protection GTO’s inherent obstruction settings, even when properly adjusted, may not be sensitive enough to prevent bodily injury in some circumstances. For this reason, safety devices such as safety edge sensors (or photoelectric sensors), which stop and reverse g[...]

IMPORT ANT SAFETY INSTRUCTIONS Mighty Mule 352 7 ! Warning signs (4 enclosed) to be installed on each side of the gate (3–5 feet above the bottom of the gate). This label is located under rear mount on the opener . Logo and warning labels (2) installed on each side of opener housing. 1-800-543-GA TE (4283) • www .mightymule.com 1. KEEP CLEAR! G[...]

8 Mighty Mule 352 P arts List - Opener and Mounting Hardware Hairpin Clip (4) 3/8" x 1-1/2" Clevis Pin (4) 5/16" x 1-3/4" Bolt (2) 3/8" x 2" Bolt (2) 3/8" x 3" Bolt (4) 3/8" x 8" Bolt (8) 8" Nylon Cable Tie (14) 3/8" Washer (18) 3/8" Lock Washer (14) 5/16" Washer (2) 3/8" Nu[...]

Mighty Mule 352 9 T ools Needed • Center Punch • Open End Wrenches — 3 /8", 7 /16", 1 /2", and 9 /16" • Small (Flat Bladed) Screwdriver • T ape Measure • Level • Wire Strippers • Phillips Screwdriver/ Large • C-Clamps — small, medium, and large • Power Drill • 3 /8" Drill Bit • Hacksaw or Heavy Dut[...]

10 Mighty Mule 352 DRIVE • Low friction screw drive (linear actuator) rated for -5 ºF to +160 ºF (-21 ºC to +71 ºC). • Powered by a 12 V motor with integral case hardened steel gear reducer . Motor speed reduced to 260 rpm. Generates 520 inch lb. of torque at 12 V . • Maximum opening arc of 110º. Approximate opening time (90º): 18 secon[...]

Mighty Mule 352 11 Preparation of the Gate Step 1 The gate must be plumb, level, and swing freely on its hinges. Wheels must not be attached to the gate. The gate must move throughout its arc without binding or dragging on the ground. Note that gates over 250 lb. should have ball bearing hinges with grease fittings. Step 2 The fence post must be s[...]

12 Mighty Mule 352 Thin Walled Tube Gate Steel Pipe Cut in Half Gate Bracket Gate Bracket Wood or Metal Reinforcement Gate Bracket Panel Gate 1" x 6" Wood Reinforcement (not supplied) (not supplied) Installation of Mounting Hardware The position of the post bracket determines the leverage and efficiency of the opener . The post bracke[...]

Mighty Mule 352 13 Determining the Mounting Position of the Post Bracket Assembly and the Gate Bracket Step 5 With the gate in the open position (up to 110º from its closed position), and the opener fully retracted, adjust the post bracket assembly and gate bracket until the opener is level. While holding the opener level, use C-clamps to temporar[...]

14 Mighty Mule 352 Gate in the CL OSED POSITION Pinch Area Gate in the OPENED POSITION Pinch Area 2" minimum 2" minimum Be sure gate opener and bracket don't bind. Step 6 After verifying that you have the best position for the post pivot bracket in the open position, insert the 5/16" x 1-3/4" bolt through the aligned holes [...]

Mighty Mule 352 15 Installing the Post Bracket Assembly and Gate Bracket Step 7 Mark reference points for bolt holes on the fence post through middle of bracket slots. Marking reference points in this manner allows room for adjustment when mounting the post bracket assembly and gate bracket. After marking your reference points, remove the opener an[...]

16 Mighty Mule 352 Mounting the Master Opener Step 11 Attach the opener to the securely bolted post bracket assembly and gate bracket using cle vis pins, b ushings, and hairpin clips, or optional Pin Locks (see Accessory Catalog ). V erify that the opener is lev el and adjust the post bracket assembly if necessary . Level Opener Gate In Open P osit[...]

Mighty Mule 352 17 Step 3 Attach a vertical closed position stop plate to the SECOND gate. Using appropriate hardware for your type of gate attach the vertical closed position stop plate to the SECOND gate frame at the point where it will come in contact with the ground stop post. Do not t ighten it completely at this time. Y ou must slide the clos[...]

18 Mighty Mule 352 Post Bracket Assembly Gate Bracket MASTER Gate Opener Closed Position Positive Stop Plates SECOND Gate Opener OPTIONAL Closed Position Ground Stop Post Check List • The gate is plumb, level, and swings smoothly on its hinges. • A plate or support was added for the gate bracket (if necessary). • The openers are level and mou[...]

Mighty Mule 352 19 Master Opener Second Opener T rench cut across driveway for routing of the Communication Cable and Second Battery Harness Cable. 32 foot Second Battery Harness Cable and 32 foot Communication Cable routed through the PVC conduit. 3/4 inch or larger PVC Conduit Preparing to Connect the Wires Trench and Lay Conduit for Wiring In or[...]

20 Mighty Mule 352 ON/OFF C ontrol Board Access C over Control Board Master Battery Harness Connector Receiver Wires Communication Cable (LINK) ON/OFF Switch ON/OFF ON/OFF ON/OFF Master Battery Harness Connector 10 Foot Battery Harness Cable Step 1 With the MASTER opener mounted in the upside down position remove the Control Board Access P anel on [...]

Mighty Mule 352 21 ON/OFF ON/OFF C ontrol Board Access C over Control Board Second Battery Harness Connector (32’) Communication Cable (LINK) ON/OFF Switch ON/OFF Step 1 With the SECOND opener mounted in the upside down position remove the Control Board Access P anel on the bottom of the opener arm. Step 2 Connect the Communication Cable coming o[...]

22 Mighty Mule 352 Powering Options: Transformer or Solar IMPORT ANT: • The Mighty Mule 352 is designed and intended for use with a 12 V olt automotive or marine type battery . The battery must be placed inside a weatherproof case and located within 6 feet of the opener arm. The 10 foot harness supplied connects the battery to the master arm. •[...]

Mighty Mule 352 23 Master Opener PVC Conduit BLACK to NEGA TIVE 32 ft Second Opener Battery Harness Cable run through PVC 10 ft Master Opener Battery Harness Cable 32 ft Communication Cable RED to POSITIVE Attach the 10 foot battery harness wires provided, to the terminals of the battery . T ake care to attach the BLACK wire to the NEGA TIVE termin[...]

24 Mighty Mule 352 Connecting the Transformer GT O indoor Tr ansformer (surge protector not supplied) Run 1000' (max.) of low voltage wire to control board from transformer (wire not included) . PVC conduit (not included) to protect wire from lawn mowers and weed eaters. Master Opener Step 1 Select the 120 V olt electrical outlet into which yo[...]

Mighty Mule 352 25 Step 5 Plug the transformer into the electrical outlet. (Use of a surge protector with the transformer is strongly recommended - not included) If electrical outlet is located outdoors, outlet and transformer should be protected by a weatherproof cover . Step 4 At the AC outlet strip 1 / 2 " of insulation from the ends of the[...]

26 Mighty Mule 352 DIP Switch #4 - Lock/Beacon This DIP selects the mode of operation of the "AUX OUT" terminal. The OFF (factory) setting is selected when the Mighty Mule Automatic Gate Lock is used with the Mighty Mule 352. The RED wire from the lock is connected to the "AUX OUT +" terminal and the BLACK wire from the lock is [...]

Mighty Mule 352 27 1 ON 2 3 4 15 CHARGING POWER S TA TUS RF PULL -PUSH MODE1 MODE2 LOCK/BEACON OFF 120 MIN MAX STALL FORCE CLOSE TIME SET LIMIT LEARN REMOTE AUX OUT SOLAR P ANEL 18VAC RECR GRN BLK RED EXIT SAFETY EDGE CYCLE COMMON LINK OFF 120 CL OSE TIME 1 ON 2 3 4 RF PULL -PUSH MODE1 MODE2 LOCK/BEACON OFF 120 MIN MAX STALL FORCE CLOSE TIME SET LI[...]

28 Mighty Mule 352 Installing the Receiver Use the transmitter to check the range of the receiver before permanently mounting it. Consider the following when mounting the receiver: • Standard receiver cable length is 10 feet (receivers with a longer cable are available as special order items; call the GTO Sales Department) . NEVER splice receiver[...]

Mighty Mule 352 29 Fully Open Position Fully Closed Position Setting the Closed Position Limit 1 ON 2 3 4 15 CHARGING POWER S TA TUS RF PULL -PUSH MODE1 MODE2 LOCK/BEACON OFF 120 MIN MAX STALL FORCE CLOSE TIME SET LIMIT LEARN REMOTE AUX OUT SOLAR P ANEL 18VAC RECR GRN BLK RED EXIT SAFETY EDGE CYCLE COMMON LINK SET LIMIT Button MASTER CONTROL BOARD [...]

30 Mighty Mule 352 1 ON 2 3 4 15 CHARGING POWER S TA TUS RF PULL -PUSH MODE1 MODE2 LOCK/BEACON OFF 120 MIN MAX STALL FORCE CLOSE TIME SET LIMIT LEARN REMOTE AUX OUT SOLAR P ANEL 18VAC RECR GRN BLK RED EXIT SAFETY EDGE CYCLE COMMON LINK LEARN REMOTE Button Master Arm Control Board 2. Set the transmitter DIP Switches There are nine (9) transmitter DI[...]

Mighty Mule 352 31 Connecting Additional Safety Devices Although GTO strongly recommends the use of additional safety devices, we do not endorse any specific brand names. Only use products that are certified and listed to be in compliance with any app lica ble UL s tand ards (Un derwriters Laboratories) and national and regional safety codes. Cal[...]

32 Mighty Mule 352 1 AUX OUT (+): (T ypically for use with automatic gate lock or light) • Provides 12Vdc power @ a maximum of 2 Amps or less than 25 watts when the gate is in motion. 2 AUX OUT (-): (T ypically for use with automatic gate lock or light) • Provides 12Vdc power @ a maximum of 2 Amps or less than 25 watts when the gate is in motio[...]

Mighty Mule 352 33 CHARGING POWER RF AUX OUT SOLAR P ANEL 18VAC RCVR GRN BLK RED EXIT SAFETY EDGE CYCLE COMMON LINK GT O Photo Beams GT O Loop Detector GTO Automatic Lock Mighty Mule Push Button Control According to Application Mighty Mule V ehicle Sensor Refer to V ehicle Sensor manual for additional connections. Edge Sensor ON 1 2 3 4 5 6 7 8 9 1[...]

34 Mighty Mule 352 ON/OFF – o Battery Harness Wi res T ransformer or Solar Wires Receiver Wi res Communication Cable (LINK) Accessory Wi res Neatly arrange all wires to lay flat as they come out of the opener . Mighty Mule 352 Master Opener Wire Routing Routing Pin 20 amp fuse 20 The master opener's battery harness wire has an in-line 20 Amp[...]

Mighty Mule 352 35 Final Step When everything has been connected to the opener ... Replace the control board access cover . If you were working with the opener with the control board access facing up, remove the opener arm from both mounts and remount it in the upright position (control board cover facing down). Failure to remount opener in the up [...]

36 Mighty Mule 352 Gate in the Closed Position Pinch Area (gray) Gate in the Open Position Pinch Area (gray) 2" minimum 2" minimum Determining The Mounting Position of The Post Bracket Assembly Step 1 With the gate in the closed position (up to 110º from its open position), and the opener fully retracted, adjust the post bracket assembly[...]

Mighty Mule 352 37 Step 3 With the gate in the fully closed position and the opener retracted, swing the opener to the gate. Mark reference points for bolt holes on gate cross member through middle of gate bracket slots. The opener must be level. (Some vertical adjustment is possible by sliding the post bracket assembly up and down.) Drill 3 / 8 &q[...]

38 Mighty Mule 352 Step 3 Save the setting by pressing the transmitter and allowing the gates to return to the fully closed position. YOUR OPEN POSITION LIMIT IS NOW PROGRAMMED . Step 4 Repeat step 2-3 for the other arm that has not been programmed in step 2. TESTING YOUR OPEN LIMIT SETTING: Press your entry transmitter and allow your gate to open.[...]

Mighty Mule 352 39 Audible/Buzzer/Alarm F eedback: 1. 1 beep with 2 seconds off: Limit switch error: Limit switch’s normally open and normally close inputs both open or both shorted. Circuit board is indicating faulty limit switch inside the operator . The alarm will automatically shut off in 4 seconds after the problem is corrected. Call T ech S[...]

40 Mighty Mule 352 2. ST A TUS LED (LED1): While the unit is IDLE: 1 blink with 2 seconds off: Free Exit terminal is shorted to common. Check exit wand or loop detector . 2 blink with 2 seconds off: Safety terminal is shorted to common. Check photo beams or loop detector . 3 blink with 2 seconds off: Edge terminal is shorted to common. Check edge s[...]

Mighty Mule 352 41 If your Mighty Mule ® 352 Gate Opener is not operating properly , please follow the steps below: 1. First use the procedures found in the Visual and Audible Diagnostic Indicators section (see page 39). 2. Use the Online T roubleshooter at http://support.gtoinc.com/support/troubleshooter .aspx. 3. If you are unable to solve the p[...]

42 Mighty Mule 352 I F THIS OPENER WILL BE USED WITH GA TES THA T ARE MOUNTED ON MASONRY , BRICK, OR ROCK (etc.) COLUMNS: READ THE FOLL OWING CAREFULL Y BEFORE PROCEEDING A. The simplest solution is to install the opener in a push-to-open configuration (requires Push-T o- Open Bracket, see Accessory Catalog). The minimum clearance is easier to ach[...]

Mighty Mule 352 43 Accessories are Available F rom Y our Retail Store ® E- Z GA TE OPENERS ACCES SORIES Solar P anel (FM123) 10 watt (FM121) 5 watt -requirestwo-5wattpanels The Solar P anel is a 10 watt solar powered battery charger for use with the FM350 & FM352 gate operator systems. P articularly suited for remote installa[...]

If you have a question about any special order item, just call 1-800-543-GA TE! Accessories are Available F rom Y our Retail Store (con't) The contents of all material available on this installation manual are copyrighted by GTO , Inc. (“GTO”), unless otherwise indicated. All rights are reserved by GTO , and content may not be reproduced, [...]