Deutsch dropdown-ico

Hearth and Home Technologies RHW-485H Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Hearth and Home Technologies RHW-485H an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Hearth and Home Technologies RHW-485H, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Hearth and Home Technologies RHW-485H die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Hearth and Home Technologies RHW-485H. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Hearth and Home Technologies RHW-485H sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Hearth and Home Technologies RHW-485H
- Den Namen des Produzenten und das Produktionsjahr des Geräts Hearth and Home Technologies RHW-485H
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Hearth and Home Technologies RHW-485H
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Hearth and Home Technologies RHW-485H zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Hearth and Home Technologies RHW-485H und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Hearth and Home Technologies finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Hearth and Home Technologies RHW-485H zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Hearth and Home Technologies RHW-485H, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Hearth and Home Technologies RHW-485H widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 1 Owner ’ s Manual Installation and Operation Models: RHW -485, RHW -485H Woodburning Fireplace DO NOT DISCARD THIS MANUAL CAUTION • Important operating and maintenance instructions included. • Leave this manual with party responsible for use and operation. • Read, understand and follow t[...]

  • Seite 2

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 2 Read this manual before installing or operating this fi replace. Please retain this owner ’ s manual for future reference. Congratulations on selecting a Heat & Glo wood burning fi re- place. The Heat & Glo fi replace you have selected is designed to provide the utmost in safety , [...]

  • Seite 3

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 3 T able of Contents 1 Listing and Code Approvals 4 A. Appliance Certi fi cation . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 Getting Started 5 A. Design and Installation Considerations . . . . . . . . . . . . 5 B. Negative Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

  • Seite 4

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 4 1 1 Listing and Code Appro v als A. Appliance Certi fi cation This fi replace system has been tested and listed in accor- dance with UL 127 and ULC-S610 standards by Underwrit- ers Laboratories Inc. for installation and operation in the United States and Canada. This fi replace has been test[...]

  • Seite 5

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 5 2 2 Get ting Star ted A. Design and Installation Considerations Draft is the pressure difference needed to vent fi replaces successfully . Considerations for successful draft include: • Preventing negative pressure • Location of fi replace and chimney B. Negative Pressure Negative pressur[...]

  • Seite 6

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 6 Location of the fi replace and chimney will af fect performance. As shown in Figure 2.1 the chimney should: • Be installed through the warm airspace enclosed by the building envelope. This helps to produce more draft, especially during lighting and die-down of the fi re. • Penetrate the h[...]

  • Seite 7

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 7 C. T ypical Fireplace System The Heat & Glo fi replace system consists of the following: • Fireplace/integral grate/refractory/outside air system • Chimney termination cap • Chimney system • Hearth extension T ermination cap Chimney penetrates roof preferably without affecting roof[...]

  • Seite 8

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 8 Before beginning the installation be sure the following tools and building supplies are available: Reciprocating saw Framing material Pliers High temp caulking material Hammer Gloves Phillips screwdriver Framing square Flat blade screwdriver Electric drill and bits Plumb line Safety glasses Lev[...]

  • Seite 9

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 9 3 3 F raming and Clearances A. Selecting Fireplace Location Several options are available to you when choosing a loca- tion for your fi replace. This fi replace may be used as a room divider , installed along a wall, across a corner or used in an exterior chase. See Figure 3.1. A F D G C 5/8 [...]

  • Seite 10

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 10 B. Clearances 2 in. (51 mm) min. 0 in. to level of standoffs Attic Insulation Shield Ceiling Firestop (ceiling) (roof) (attic) (ceiling) Ceiling Firestop Offset/Return with hanger straps Storm Collar Roof Flashing 3/4 in. (19 mm) to side of appliance (except at nailing flanges where it is 1/2 [...]

  • Seite 11

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 11 C. Sidewalls/Surrounds Adjacent combustible side walls must be located a minimum of 12 in. (305 mm) from the fi replace opening. See Figure 3.3. If you are using a decorative surround constructed of combustible material, it must be located within the shaded area de fi ned in Figure 3.3. Shor[...]

  • Seite 12

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 12 E. Construct the Chase A chase is a vertical boxlike structure built to enclose the fi replace and/or its vent system. V ertical chimneys that run on the outside of a building may be, but are not required to be, installed inside a chase. Construction of the chase may vary with the type of bui[...]

  • Seite 13

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 13 A. Install the Outside Air Kit Using an outside air kit is highly recommended to minimize the effects of negative pressure within the structure. W e recommend you utilize the shortest duct run to optimize the performance of the outside air kit. Cold air fl ow can be mini- mized by putting a s[...]

  • Seite 14

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 14 Handle left - open Handle right - closed Figure 4.4 Locating the Outside Air Control Outlet placed higher than 3 ft below the termination cap Attic space Garage or combustible liquids storage Outlet blocked by snow , leaves, etc. Clear area outside house or in ventilated crawl space YES NO NO [...]

  • Seite 15

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 15 B. Secure the Fireplace • Position the Fireplace This fi replace may be placed on either a combustible or noncombustible continuous fl at surface. Follow the in- structions for framing in Section 3.D. Slide the fi replace into position. Be sure to provide the minimum air clear- ance at th[...]

  • Seite 16

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 16 NOTE: • Chimney performance may vary . • Trees, buildings, roof lines and wind conditions af fect performance. • Chimney height may need adjustment if smoking or overdraft occurs. Chimney must extend beyond combustible roof structure Maintain minimum height of chimney above roof Addition[...]

  • Seite 17

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 17 A. Chimney Requirements V ertical distances are measured from the base of the fi re- place as shown in Figure 5.2. T o determine the chimney components needed to complete your particular installation, follow the steps below: • Determine the total vertical height of the fireplace installatio[...]

  • Seite 18

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 18 B. Using Offsets/Returns T o bypass any overhead obstructions, the chimney may be offset using a 15-deg (SL315) or 30-deg (SL330) of fset/re- turn. An offset and return may be attached together or a chimney section(s) may be used between an offset and return. Perform the following steps to det[...]

  • Seite 19

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 19 C. Assemble the Chimney Sections Attach either a straight chimney section or an offset to the top of the fi replace (depending on your installation require- ment). Chimney sections are locked together by pushing downward until the top section meets the stop bead on the lower section. The inne[...]

  • Seite 20

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 20 E. Install the Attic Insulation Shield An insulation shield must be installed when there is a pos- sibility of insulation coming into contact with the factory built chimney system. • Bend the tabs at the top of the attic insulation shield inward. This will help keep the chimney section cente[...]

  • Seite 21

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 21 Slanted Roofs Flat Roofs Chimney must extend 3 ft (.9 m) above the roof Chimney must extend 2 ft (.6 m) above any portion of the roof within 10 ft (3 m) of the chimney Chimney must extend 3 ft (.9 m) above the roof Chimney must extend 2 ft (.6 m) above any portion of the roof within 10 ft (3 m[...]

  • Seite 22

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 22 T ermination Cap Storm Collar Slope Downward T urn-down Drip Edge Chase (Chimney) 2 in. (51 mm) Collar on Chase T op Caulk .018 (26 ga) min. Galvanized Chase T op Figure 6.4 Chase T op Construction Install the Chimney Air Kit (required in Canada): When installing the chimney air kit, follow th[...]

  • Seite 23

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 23 2 in. (51 mm) min. 4-1/2 in. (1 14 mm) max. 1-1/2 in. (38 mm) min. overlap Cap Standoff T op of Pipe Flashing Collar Figure 6.7 Installing an ST375 Square T ermination Cap T op of Pipe 2 in. (51 mm) min. Flashing Collar 1-1/2 in. (38 mm) min. overlap 3 in. (76 mm) max. Figure 6.8 Installing a [...]

  • Seite 24

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 24 A. Gas Log/Lighter Provisions A certi fi ed gas log lighter or decorative gas log set can be installed in this fi replace. • Maximum input is 100,000 BTU/hr . • Decorative gas appliance must be certi fi ed to ANSI Z21.60 “Standard for Decorative Gas Appliances for Installation in V en[...]

  • Seite 25

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 25 8 8 Fin i sh in g A. Hearth Extension A hearth extension must be installed with all fi replaces to protect the combustible fl oor in front of the fi replace from both radiant heat and sparks. See Figures 8.1 -8.3. 2 in. (51 mm) required High temperature (300°F min.) continuous, non-combust[...]

  • Seite 26

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 26 B. Finishing Material • Combustible Material Material which is made of or surfaced with wood, compressed paper , plant fi bers, plastics, or any material capable of igniting and burning, whether fl ame proofed or not, plastered or not plastered. • Non-Combustible Material Material which [...]

  • Seite 27

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 27 HOT! DO NOT TOUCH. SEVERE BURNS MA Y RESUL T . CLOTHING IGNITION MA Y RESUL T . • Keep children away . • CAREFULL Y SUPERVISE children in same room as fi replace. • Alert children and adults to hazards of high temperatures. • Do NOT operate with protective barriers removed. • Keep c[...]

  • Seite 28

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 28 D. Flue Damper The fl ue damper must be in full open position, and is oper- ated by moving the handle up toward the top of the fi replace. Before lighting the fi re, verify this by looking up from the in- side of the fi replace. Always operate this fi replace with the damper fully open. P[...]

  • Seite 29

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 29 G. Grate The factory installed integral grate must be used to hold the logs from falling out of an open fi replace and to allow air to pass between the burning logs. It is important to keep the fi re off the hearth and to allow the ashes to collect beneath the fi re, thereby forming a layer[...]

  • Seite 30

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 30 I. Starting a Fire Check the fl ue damper to be certain it is in the full open po- sition. Place crumpled or twisted paper under the fi replace grate. Loosely arrange kindling or small pieces of wood to form a layer above the paper . The fi res must be built on the fi replace grate, withou[...]

  • Seite 31

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 31 1 0 10 T roubleshooting Another appliance in home also exhausting air (furnace, fan, dryer , etc.)? Air register from furnace near fireplace? Doors opening and closing? Window closed for start-up? Outside air closed? Overhead fan operating? Overhanging tree? Bird's nest or leaves in termi[...]

  • Seite 32

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 32 Diagnostic Questions Possible Causes of Condition Solutions Is the damper open? • No draft Open damper . Is there enough paper/starter? • Insuf fi cient heat to ignite kindling Use more paper/starter . Is there enough kindling? Is the kindling dry? • Insuf fi cient heat to ignite fuel [...]

  • Seite 33

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 33 Diagnostic Questions Possible Causes of Condition Solutions Do you have glass doors? • Need to slow air intake Add glass doors. What is the condition of the wood? • Extremely dry wood Mix in less seasoned wood after fi re established. Diagnostic Questions Possible Causes of Condition Solu[...]

  • Seite 34

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 34 A. Disposal of Ashes Ashes should be placed in a metal container with a tight- fi t- ting lid. The closed container of ashes should be placed on a noncombustible fl oor or on the ground, well away from all combustible materials, pending fi nal disposal. If the ashes are disposed of by buria[...]

  • Seite 35

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 35 Fire Risk • Do not use chimney cleaners or fl ame colorants in your fi replace. Will corrode chimney . W ARNING D. Maintenance T ask List Asphyxiation Risk Fire Risk Annual inspection by qualified technician recommended. Check: • Condition of doors, surrounds and fronts • Condition of [...]

  • Seite 36

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 36 1 2 12 Reference Materials A. Fireplace Dimensions 23-3/8 in. (594 mm) 8-1/8 in. (206 mm) A 10-1/2 in. (267 mm) dia. 6-1/2 in. (165 mm) 37-3/4 in. (959 mm) 4-1/4 in. (108 mm) 9-5/8 in. (244 mm) 8-5/8 in. (219 mm) 13-1/2 in. (343 mm) Gas Knockout Outside Air 9-1/4 in. (235 mm) 41-1/4 in. (1048 [...]

  • Seite 37

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 37 B. Fireplace Components GR23 & GR24 Integral Grate Bi-fold Glass Doors DM1736 DM1742 Perception Glass Doors DP1736 DP1742 Herringbone Pattern Refractory T raditional Brick Pattern Refractory 16 in. (406 mm) 52 in. (1321 mm) 1/2 in. (13 mm) HX3 Hearth Extension 20 in. (508 mm) 66 in. (1676 [...]

  • Seite 38

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 38 C. Chimney Components The following pictures show only those chimney components which may be safely used with this fi replace. 10-1/2 in. (267 mm) 12 in. (305 mm) 12 in. (305 mm) 5-1/4 in. (133 mm) 4 in. (102 mm) CAK4A Chimney Air Kit ID4 Insulated Duct UD4 Uninsulated Duct 42 in. (1067 mm) 4[...]

  • Seite 39

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 39 SL315/SL330 Offset/Return A B 14-1/2 in. (368 mm) Ceiling Firestop 24 in. (610 mm) 14-1/2 in. (368 mm) AS8 Straight Attic Insulation Shield 2 in. (51 mm) 10-1/2 in. (267 mm) JB877 Chimney Joint Band 10-1/2 in. (267 mm) CB876 Chimney Joint Band 12 in. (305 mm) 31 in. (787 mm) 24-5/8 in. (625 mm[...]

  • Seite 40

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 40 TR344 Round T ermination Cap TR342 Round T elescoping T ermination Cap ST375 Square T ermination Cap TS345/TS345P Square T ermination Cap TCT375 T erra Cotta Cap 72 in. (1829 mm) 36 in. (914 mm) 2 in. (51 mm) 10-7/8 in. (276 mm) CT35 Chase T op A B C D LDS33/LDS46 Decorative Shroud 15-3/4 in. [...]

  • Seite 41

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 41 CT3-Queen CT3-Bishop CT3-Pawn CT3-Knight CT3-King 21 in. (533 mm) 46-3/4 in. (1 187 mm) 24 in. (610 mm) 18-1/4 in. (464 mm) 40-1/8 in. (1019 mm) 20 in. (508 mm) 16 in. (406 mm) 31-7/8 in. (810 mm) 18 in. (457 mm) 21 in. (533 mm) 24-3/4 in. (629 mm) 20-5/8 in. (524 mm) 20-3/4 in. (527 mm) 35-5/[...]

  • Seite 42

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 42 Woodburning T ermination Cap Shroud TS345 / 445 (T op V ent) TR342 / 344 TR442 / 444 TR342 / 344 TV TR442 / 444 TV (with TR-TVK installed) TR1 1 / 1 1T TR1 1 / 1 1T TV (with TR-TVK installed) OPEN TOP with solid sides and 3 in. opening at the bottom. Minimum Base Dimensions (Inches) 23 X 23 28[...]

  • Seite 43

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 43 This page intentionally left blank.[...]

  • Seite 44

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 44 D. Service Parts Exploded Parts Diagram RHW-485 Service Parts RHW -485 Beginning Manufacturing Date: N/A Ending Manufacturing Date: Active T raditional Brick Herringbone Brick 3 2 1 3 7 5 4 6 11 9 (Damper Control Handle) 15 1 14 2 13 16 12 10 8 3[...]

  • Seite 45

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 45 Service Parts List RHW-485 Service Parts RHW -485 Beginning Manufacturing Date: N/A Ending Manufacturing Date: Active # Description of Part RHW-485 RHW-485H Qty . Refractory Retainer 1 1847 1 1847 3 1 T raditional Brick Back Refractory 28394 1 2 T raditional Brick Hearth Refractory 28391 1 3 T[...]

  • Seite 46

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 46 This page intentionally left blank.[...]

  • Seite 47

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 47 E. Limited W arranty W ARRANTY FOR HEA T & GLO FIREPLACES The limited warranty will not become effective until you have mailed the completed warranty card to: Hearth & Home T echnologies Inc. 20802 Kensington Blvd., Lakeville, MN 55044. This card must be mailed within 60 days of the fi[...]

  • Seite 48

    Heat & Glo • RHW-485 • 33221 Rev O • 08/06 48 Hearth & Home T echnologies Inc. 800 W . Jef ferson Lake City , MN 55041 Please contact your Heat & Glo dealer with any questions or concerns. For the number of your nearest Heat & Glo dealer , please call 1-888-427-3973. – NOTES – F . Contact Information DO NOT DISCARD THIS MA[...]