Honda Power Equipment WT40X Bedienungsanleitung

WT20X-40 取説表紙 31YG0602 C 2002-2009 Honda Motor Co., Ltd. -All Rights Reserved Owner , s Manual WATER PUMP WT20X ・ WT30X ・ WT40X Printed in Japan 英 N AH HC Hi EM3 DIC F101 (PF)  BK K2 ： WT40X K3 ：W T20X, WT30X 31YG0602 00X31-YG0-6020 2000.2009.03[...]

Keep this owner’s manual handy, so you can refer to it at any time. This owner’s manual is considered a per manent part of the water pump and should remain with the water pump if resold. The information and specifi cations included in this pub lication were in effect at the time of approval f or printing. Honda Motor Co., Ltd. reserves the righ[...]

1 INTRODUCT ION Congratulations on your selection of a Honda water pump. We are certain you will be pleased with your purchase o f one of the f inest water pumps on the market. We want to help you get the be st results from your new water pump and to operate it safely. Th is manual contains the info rmation on how to do that; please read it careful[...]

2 INTRODUCTION A FEW WORDS ABOUT SAFETY Safety Labels Safety Messages Safety Headings Safety Section Instructio ns Your safety and the safety of others are very important. And using this water pump safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on [...]

3 CON TENTS .......................................................................................... PUMP SAFETY . 5 ........................................................................ CONTROLS & FEATURES . 9 ............................................................................. BEFORE OPERATION . 12 ..............................[...]

4 CONTENTS SERVICING YOUR PUMP (continued) ................................................................................................ STORAGE . 41 ..................................................................................... TRANSPORTING . 47 ..................................... TAKING CARE OF UNEXPECTED PROBLEMS . 48 ...............[...]

5 IMPORTANT SAFETY INFORMATION Refuel With Care Pump Operati on Operator Responsibility PUMP SAFETY Gasoline is extremely flammable, and gasoline vapor can explode. Refuel outdoors, in a well-ventilated area, with the engine sto pped and the pump on a level surface. Do not fill the fuel tank above the fuel strainer shoulder. Never smoke near gasoli[...]

6 PUMP SAFETY Hot Exhaust Carbon Monoxide Hazard The muffler becomes very hot during operation and rem ains hot for a while after stopping the engine. Be careful not to touch the muffler while it is hot. Let the engine cool before transporting the pump or storing it indoors. To prevent fire hazards, keep the pump at least 3 feet (1 meter) away from[...]

7 PUMP SAFETY SAFETY LABEL LOCATIONS PUMP CAUTION LABEL WT20X The labels shown here contain important safety information. Please read them carefully. These labels are considered permanent parts of your pump. If a label co mes off or beco mes hard to read, contact an authorized Honda servicing dealer for a replacement. 09/02/16 10:46:13 31YG0600_008[...]

8 PUMP SAFETY PUMP CAUTION LABEL WT30X · WT40X 09/02/16 10:46:23 31YG0600_009[...]

＜＞ 9 COMPONENT & CONTROL LOCATIONS WT20X CONTROLS & FEA TURES THROTTLE LEVER CHOKE LEVER STARTER GRIP FUEL VALVE LEVER IGNITION SWITCH OIL FILLER CAP/DIPST ICK PRIMING WATER FILLE R CAP SUCTION PORT STRAINER FUEL FILLER CAP AIR CLEANER CASE DRAIN PLUG DISCHARGE PORT MUFFLER PRIMING WATER FILLE R CAP WRENCH PUMP DRAIN PLUG 09/02/16 10:46[...]

10 CONTROLS & FEATURES CONTROLS Fuel Valve Lever Ignition Switch Choke Lever ON ON O O F F F F FUEL VALVE LEVER O O F F F F IGNITION SWITCH CHOKE LEVER C C L L O O S S E E D D O O P P E E N N The fuel valve opens and closes the connection between the fuel tank and the carburetor. The fuel valve lever must be in the ON position for the engine to[...]

11 CONTROLS & FEATURES Throttle Lever Recoil Starte r Grip FEATURES Oil Alert System SLOW THROTTLE LEVER CHOKE LEVER F F A A S S T T The throttle lever controls engine speed. Moving the throttle lever in the directions shown makes the engine run faster or slower. Pump output is controlled by adjusting the throttle lever. At maximum throttle pos[...]

12 BEFORE OPERAT ION ARE YOU READY TO GET STARTED? Knowledge Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury. Read and understand this manual. Know what the controls do and how to operate them. Familiarize yourself with the pump and its operation be fore you begin pumping. Know wh[...]

13 BEFORE OPERATION IS YOUR PUMP READY TO GO? Check the General Conditi on of the Pump For your safety, and to maximize the service life of your equipment, it is very important to take a few m oments before you operate the pump to check its condition. Be sure to take care of any problem you find, or have your servicing dealer corr ect it, before yo[...]

14 BEFORE OPERATION Check the Suction and Dischar ge Hoses Check the Engine Check the general conditi on of the hoses. Be s ure the hoses are in serviceable condition before connectin g them to the pump. Remember that the suction hose must be reinforced construction to prevent hose collapse. Check that the sealing washer in the suction hose connect[...]

15 OPERA TION SAFE OPERATING PRECAUTIONS To safely realize the full potential of this pump, you need a complete understanding of its o peration and a c ertain amount of practice with its controls. Before opera ting the pump for the first time, please review the IMPORTANT SAFETY INFORMATION on page and the chapter titled BEFORE OPERATION . For your [...]

16 OPERATION PUMP PLACEMENT SUCTION HEAD DISCHARGE HEAD T T O O T T A A L L H H E E A A D D For best pump performance, place the p ump near the water level, and use hoses that are no longer than necessary. That will enable the pump to produce the greatest output with the least self-priming time. As head (pumping height) increases, pump output decre[...]

17 OPERATION SUCTION HOSE INSTALLATION HOSE CONNECTOR SUCTION HOSE HOSE CLAMP HOSE CLAMP RING SUCTION PORT STRAINER HOSE CLAMP HOSE CLAMP H H O O S S E E C C O O N N N N E E C C T T O O R R SUCTION HOSE SEALING WASHER (co mmercially available) HOSE COUPLER (commercially available) SUCTION HOSE (commercially available) Use the commercially available[...]

18 OPERATION DISCHARGE HOSE INSTALLATION PRIMING THE PUMP HOSE CONNECTOR HOSE CLAMP DISCHARGE HOSE PRIMING WATER FILLE R CAP WATER Use a commercia lly available hose and hose connector, and clamp provided with the pump. It is best to use a short, large- diameter hose, because that will reduce fluid fric tion and improve pump performance. A long or [...]

19 OPERATION STARTING THE ENGINE F F U U E E L L V V A A L L V V E E L L E E V V E E R R CHOKE LEVER THROTTLE LEVER C C L L O O S S E E D D ON F F A A S S T T Move the fuel valve lever to the ON position. Move the throttle lever away from the SLOW position, about 1/ 3 of the way toward the FAST position. To rest art a warm en gine, l eave the chok [...]

20 OPERATION ON IGNITION SWITCH STARTER GRIP Direction to pull Turn the ignition switch to the ON position. Pull the starter grip lightly until you f eel resistance, then pul l briskly in the direction of the arrow as shown below. Return the starter grip gently. 4. 5. 07/05/29 13:24:52 31YG0600_021[...]

21 OPERATION SETTING ENGINE SPEED CHOKE LEVER SLOW O O P P E E N N F F A A S S T T THROTTLE LEVER If the choke lever was moved to the CLOSED position to start the engine, gradually move it to the OPEN pos ition as the e ngine warms up. After starting the engine, move the throttle lever to the FAST position for self-priming, and check pump output. P[...]

22 OPERATION STOPPING THE ENGINE THROTTLE LEVER SLOW IGNITION SWITCH O O F F F F To stop the engine in an emergency, simply turn the ignition switch to the OFF position. Under normal condi tions, use the foll owing procedure. Move the throttle lever to the SLOW position. Turn the ignition switch to the OFF position. 1. 2. 02/01/14 13:21:09 31YG0600[...]

23 OPERATION FUEL VALVE LEVER O O F F F F Turn the fuel valve lever to the OFF position. After use, remove the pump drain plug (see page ), and drain the pump chamber. Remove the filler cap, and flush the pump chamber with clean, fre sh water. Allow the w ater to drain from th e pump chamber, then reinstall the filler cap and drain plug. 3. 39 02/0[...]

24 SERVICING YOUR PUMP THE IMPORTANCE OF MAINTENANCE Maintenance, replacement, or repair of emission control devices and systems may be performed by any engine repair establishment or individual, using parts that are ‘‘certified’’ t o EPA standards. Good maintenance is essential for saf e, economical, and trouble-free operation. It will als[...]

− − − 25 SERVICING YOUR PUMP MAINTENANCE SAFETY Safety Precautions Carbon monoxide poisoning from engine exhaust . Burns from h ot parts. Injury from moving parts. Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can ari se in performing maintenance. Only you can decide whether[...]

＊ ○ ○ ○ ○ ○＊ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ − − − − − − − − 26 SERVICING YOUR PUMP MAINTENANCE SCHEDULE ITEM REGULAR SERVICE PERIOD (3) Perform at every indicated month or operating hour interval, whichever comes first. Check level Change Check Clean Replace Clean Clean-adjust Replace Clean Check-ad just C[...]

27 SERVICING YOUR PUMP REFUELING MAXIMUM FUEL LEVEL Remove the fuel tank cap and check the fuel level. If the fu el level is low, ref uel in a we ll-ventilate d area with the engine stopped. If the engine h as been runnin g, allow it to cool f irst. Never refuel the engine inside a bu ilding where gasoline fumes can reach flames or sparks. Refuel c[...]

28 SERVICING YOUR PUMP FUEL RECOMMENDATIONS Spilled fuel is not only a fire hazard, it caus es environmental damage. Wipe up spills immediately. Fuel can damage paint and pla stic. Be careful no t to spill fuel when filling your fuel tank. Damage caused by spilled fuel is not covered under the Distributor’s Limited Warranty. This engine is certif[...]

29 SERVICING YOUR PUMP ENGINE OIL LEVEL CHECK OIL FILLER CAP/DIPST ICK OIL FILLER NECK UPPER LIMIT Check the engine oil level with the engine stopped and in a level position. Remove the oil filler cap/ dipstick and wipe it clean. Inse rt and remove the dips tick witho ut screwing it i nto the fill er neck. Check the oil level shown on the dipstick.[...]

30 SERVICING YOUR PUMP ENGINE OIL CHANGE OIL LEVEL DRAIN PLUG OIL FILLER CAP/DIPST ICK Drain the used oil while the engine is warm. Warm oil drains quickly and completely. Place a suitable container below the engine to catch the used oil, then remove the oil filler cap/ dipstick and the drain plug. Allow the used oil to drain completely, then reins[...]

31 SERVICING YOUR PUMP ENGINE OIL RECOMMENDATIONS AMBIENT TEMPERATU RE SAE 10W-30 is recommended for general use. Other viscosities shown in the chart may be used when the average temperature in your area is within the indicated range. Use 4-stroke motor oil that meets or ex ceeds the requi rements for API service category SJ or later (or e quivale[...]

32 SERVICING YOUR PUMP AIR FILTER INSPECTION WING NUT AIR FILTER AIR CLEANER COVER Unscrew the wing nut and remove the air cleaner cover. Check the air f ilter to be sure it is clean and in good condition. If the air fil ter is dirty, clean it as described on page . Replace the air filter if it is damaged. Operating the engine without an air filter[...]

33 SERVICING YOUR PUMP AIR FILTER CLEANING WING NUT WING NUT AIR CLEANER COVER PAPER FILTER ELEMENT FOAM FILTER ELEMENT A dirty air filter w ill restrict air flow to the c arburetor, reducing engine performance. If you operate the pump in very dusty areas, clean the air filter more freque ntly than specif ied in the Maintenance Schedule (see page )[...]

34 SERVICING YOUR PUMP SEDIMENT CUP CLEANING SEDIMENT CUP Move the fuel valve lever to the OFF position, then rem ove the fuel sediment cup and O-ring. Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spill[...]

−− − − 35 SERVICING YOUR PUMP SPARK PLUG SERVICE SPARK PLUG WRENCH SPARK PLUG CAP 0.028 0.031 in (0.70 0.80 mm) In or der to se rvice t he spark plu g, you will need a spa rk plug w rench (commercially available). Incorrect spark plugs can cause engine dam age. Disconnect the spark plug cap, and remove any dirt from around the spark plug ar[...]

− 36 SERVICING YOUR PUMP Attach the spark plug cap. A loose spark plug can overheat and damage t he engine. Overtightening the spark plug can damage the threads in the cylinder head. If installing a new spark plug, tighten 1/ 2 turn after the spark plug seats. If reinstalling the used spa rk plug, tighten 1/ 8 1/ 4 tu rn after the spark plug seat[...]

37 SERVICING YOUR PUMP SPARK ARRESTER SERVICE (optional equipment) WT20X MUFFLER MUFFLER PROTECTOR SPARK ARRESTER 4 mm SCREW 5 mm SCREW (4) Your engine is not factory-equipped with a spark arrester. In some areas, it is illegal to o perate a n engine without a spark a rrester. Check local laws and regulations. A spark arrester is ava ilable from au[...]

38 SERVICING YOUR PUMP MUFFLER SPARK ARRESTER SPARK ARRESTER SCRE EN 4 mm SCREW 5 mm SCREW (2) 5 mm SCREW (4) SPARK ARRESTER 4m m SCREW (2) WT40X type uses two 4 mm screws. MUFFLER PROTECTOR WT30X and WT40X Install the spark arrester, muffler protector, and muffler in the reverse order of disassembly. The spark arrester must be free of breaks and h[...]

39 SERVICING YOUR PUMP PUMP CASING CLEANING Removal: WRENCH WRENCH DRAIN PLUG WRENCH KNOBS (4) KNOBS (4) PUMP CASING PUMP COVER VOLUTE CASE O-RING After each use, clean the inside of the pump casing using the f ollowing procedure: Remove the drain plug f rom the pump cover using the wrench to drain the water inside. Loosen the pump cover knobs usin[...]

40 SERVICING YOUR PUMP Installation: VOLUTE CASE PUMP CASING PUMP COVER WRENCH DRAIN PLUG KNOBS (4) O-RING Install the drain plug in the pump cover . After tightening the pump cover knobs, check the pump cover and pump casing to ensure that ther e is no water leakage. Install the O-ring on the pump cover, taking care not to damage the O-ring. Insta[...]

41 STORAGE STORAGE PREPARATION Cleaning Proper storage preparation is essential for keeping your pump troublefree and looking good. The f ollowing steps will help to keep rust and corr osion from impairing your pump’s function and appearance, and will make the engine easier to start when you use the pump again. Wash the engine and pump. Wash the [...]

42 STORAGE Fuel DRAIN PLUG Stop the engine, and allow it to cool. You can extend f uel storage life by add ing a fuel stabilizer that is formulated for that purpose, or you can avoid fuel deterioration problems by draining the fuel tank and carburetor. The Distributor’s Limited Warranty does not cover fuel system damage or engine performance prob[...]

43 STORAGE Adding a Fuel Stabilizer to Extend Fuel Storage Life FUEL VALVE LEVER O O F F F F When adding a fuel s tabilizer, fill the f uel tank with fresh gas oline. If only partially filled, ai r in the tank will promote f uel deterioration during storage. If you keep a container of gasoline f or refueling, be sure that it contains only fresh gas[...]

44 STORAGE Draining the Fuel Tank and Carburet or DRAIN BOLT SEDIMENT CUP Place an approved gasoline container below the carburetor, and use a funnel to avoid spilling fuel. Remove the carburetor drain bolt and sediment cup, then move the fuel valve lever to the ON position. Gasoline is highly flammable and explosive. You can be burned or seriously[...]

− 45 STORAGE Engine Oil STORAGE PRECAUTIONS Align no tch on pulley with hole at t op of cover. Change the engine oil (see page ). Remove the spark plug (see page ). Pour a tablespoon (5 10 cc) of clean engine oil into the cylinder. Pull the starter grip several times to distribute the oil in t he cylinder. Reinstall the spark plug. Pull the start[...]

46 STORAGE REMOVAL FROM STORAGE Place the pump on a level surface. Tilting can cause f uel or oil leakage. With the engine and exhaust system cool, cover the pump to keep out dust. A hot engine and exhaust system can ig nite or melt some materials. Do not use sheet plastic as a dust cover. A nonp orous cover will trap moisture around the pum p, pro[...]

47 TRANSP ORTING If the pump has been run ning, allow the engine to cool f or at least 15 minutes before loading the pump on the transport vehicle. A hot engine and exhaust syste m can burn you and can ignite some materials. Keep the pump level when transporting to reduce the possibility of fuel leakage. Move the fuel valve lever to the OFF positio[...]

48 ENGINE TAKING CARE OF UNEXPECTED PROBLEMS Engine Wi ll Not S tar t Possi ble Ca use Corr ect ion Engine La cks Pow er Possi ble Ca use Corr ect ion Fuel valve OFF. Choke ope n. Igniti on switc h OFF . Out of fuel. Bad f uel; pump stor ed without tre ating or drai ning gas oline , or ref uel wi th bad gasolin e. Low o il level caused Oil Aler t t[...]

49 TAKING CARE OF UNEXPECTED PROBLEMS PUMP No Pump Out put Possi ble C ause Cor rec tion Low Pump O utput Possi ble C ause Cor rec tion Chec k pump chamb er. Chec k suc tion hose . Meas ure suc tion and disc harge he ad. Chec k engine . Chec k suc tion hose . Check disch arge hose. Meas ure suc tion and disc harge he ad. Chec k engine . Prime pump [...]

50 TECHNICAL & CONSUMER INFORMATION TECHNICAL INFORMATION Serial Number Location ENGINE SERIAL NUMBER FRAME SERIAL NUMBER Engine serial number: Record the frame serial number and the engine ser ial number in the space below. You will need these serial numbers when or dering parts, and when making technical or w arranty inquiries (see page ). Fr[...]

51 TECHNICAL & CONSUMER INFORMATION Carburetor Modificati on for High Altitude Operation At high altitude, the standard carburetor air-fuel mixture will be too rich. Performance will decrease, and fuel consumption will increase. A very rich mixture will also foul the spark plug and cause hard starting. Operation at an a ltitude that dif fers fr[...]

52 TECHNICAL & CONSUMER INFORMATION Emission Control System Inform ation The U.S. and California Clean Air Acts Tampering and Altering Source of Emissions The combustion process produces car bon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, the[...]

53 TECHNICAL & CONSUMER INFORMATION Problems That May Affect Emissions Replacement Parts Maintenance If you are aware of any of the follow ing symptoms, have your engine inspected and repaired by your servicing dealer. Hard starting or stalling after starting. Rough idle. Misfiring or backfiring under load. Afterburning (backfiring). Black exha[...]

＋ − ×× − − ± ± × 54 TECHNICAL & CONSUMER INFORMATION Specifications Dimensions and weight Engine design and performance Tune up Pump WT20X 24.4 in (620 mm) 18.1 in (460 mm) 18.3 in (465 mm) GX160K1 4-stroke, overhead valve, s ingle cylinder 104 lbs (47 kg) Forced air Transistor magneto Counterclockwise 1,400 rpm 9.9 cu-in (163 cm )[...]

× ± ± ×× − − ± 55 TECHNICAL & CONSUMER INFORMATION Dimensions and weight Engine design and performance Tune up Pump WT30X Length Width Height Dry mass [weight] Model Engine type Displaceme nt [bore stroke] Fuel tank capacity Engine oil capacity Cooling sys tem Ignition system PTO shaft rotation Spark plug gap Idle speed Valve clearanc[...]

± ± ± ×× − − × 56 TECHNICAL & CONSUMER INFORMATION Dimensions and weight Engine design and performance Tune up Pump WT40X Spark plug gap Idle speed Valve clearance (cold) Other specifications 1,400 150 rpm 0.15 0.02 mm 0.20 0.02 mm No other adjustments needed. 28.9 in (735 mm) 21.1 in (535 mm) 22.2 in (565 mm) 172 lbs (78 kg) GX340K1 [...]

57 TECHNICAL & CONSUMER INFORMATION CONSUMER INFORMATION Honda Publications Shop Manual Parts Catalog These publications will give you additional information for maintaining and repairing your pump. You may order them from your Honda pump dealer. This manual covers complete maintenance and overhaul procedures. It is intended to be used by a ski[...]

58 TECHNICAL & CONSUMER INFORMATION Customer Service Inform ation Servicing dealership personnel are trained pr ofessionals. They should be able to answer any question y ou may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership’s management. The Service Manager or Gener[...]

59 MEMO 07/05/29 13:28:49 31YG0600_060[...]

60 MEMO 07/05/29 13:28:51 31YG0600_061[...]

−− QUICK REFERENCE INFORMATION Unleaded gasoline with a pump octane rat ing of 86 or higher ( p a g e2 8) SAE 10W-30, API SJ or later (or equi val ent) , for gener al use ( p a g e3 1) Check engine oil level. Check air filter. Change engine oil. Refer to the maintenance s c h e d u l eo np a g e2 6. 0.028 0.031 in (0.70 0.80 mm) W20EPR-U BPR6ES[...]

WT20X-40 取説表紙 31YG0602 C 2002-2009 Honda Motor Co., Ltd. -All Rights Reserved Owner , s Manual WATER PUMP WT20X ・ WT30X ・ WT40X Printed in Japan 英 N AH HC Hi EM3 DIC F101 (PF)  BK K2 ： WT40X K3 ：W T20X, WT30X 31YG0602 00X31-YG0-6020 2000.2009.03[...]