HP (Hewlett-Packard) 686210-S01 Bedienungsanleitung

HP Pr oL ian t DL3 6 0e Gen8 S er v er Us er Gui de Abstract This document is for the person wh o installs, administers, and trouble shoots servers and storage systems . HP assumes you are qua lified in the servicing of comp uter equipment a nd trained in recognizing hazards in products with hazardo us energy levels. Part Number: 675786 - 001 July [...]

© Copyright 2012 Hewlett - Packard Development Company, L.P. The information contained herei n is subject to change without notice. The only warranties for HP products and service s are set forth in the expres s warranty statements accompanyin g such products and services. Nothing herein s hould be construed as constitutin g an additional warranty[...]

Contents 3 Con tents Component identification ............................................................................................................... 7 Front panel co mponents ............................................................................................................................. 7 Front panel LEDs and but tons ........[...]

Contents 4 Security bezel option ............................................................................................................................... 29 Front video adapter opt ion ....................................................................................................................... 29 Drive options .....................[...]

Contents 5 Auto - configuration process .............................................................................................................. 83 Boot options ................................................................................................................................ . 84 Configuring A MP modes ..........................[...]

Contents 6 HP 460 W CS powe r supply (92 % efficiency ) ................................................................................. 10 1 HP 460 W CS HE power supply (94% efficiency) ............................................................................ 101 HP 750 W CS powe r supply (92 % efficiency ) ....................................[...]

Component ident ification 7 C om ponen t i dentif i cati on F ront panel comp onents • Four - bay LFF drive model Item Description 1 Optical drive ( optional) 2 Serial number pull tab 3 Front video conne ctor (front vid eo adapte r, part number 655915 - B21 required) 4 USB connectors 5 LFF drives • Eight - bay SFF drive mode l Item Description [...]

Component ident ification 8 F ront panel LEDs and buttons Item Description Status 1 UID LED/button Blue = Identification is activated. Flashing blue = System is being managed rem otely. Off = Ident ification is de activated. 2 Power On/Standb y button and system power LED Green = System is on. Flashing green = W aiting for p ower. Amber = System is[...]

Com ponent ident ification 9 Item Description 5 NIC connecto rs (4 to 1) 6 Serial connecto r 7 Video connecto r 8 USB connectors 9 iLO connector R ear panel LEDs and buttons Item Description Status 1 NIC status LED Green = Activi ty exists Flashing green = Activity exists Off = No acti vity exi sts 2 NIC link LED Green = Link exists Off = No link e[...]

Component ident ification 10 S ystem board c omponents Item Description 1 PCI riser conne ctors 2 Cache module connector 3 TPM connector 4 Mini - SAS connector 5 System battery 6 SATA drive connector 7 SATA optical/storage drive connector 8 Front panel con nectors 9 Processor socket 1 10 GPU powe r connector 11 Fan connector 8 12 Fan connector 7 13[...]

Component ident ification 11 Item Description 21 Not applicable 22 Drive backp lane power connect or 23 Processor socket 2 24 Not applicable 25 Power suppl y connector 1 26 Drive sideb and signal connect or 27 Power suppl y connector 2 28 Processor 1 D IMM slots 29 SD card sl ot 30 NMI header 31 System maintenance switch D IMM slot locations DIMM s[...]

Component ident ification 12 Switch Default Function 3, 4, 7, 8, 9, 10, 11, 12 — Reserved When the system maintenance switch position 6 is s et to the On position, the system is prepared to er ase all system configuration settings from both CMOS and NVRAM. CAUTION: Clearing CMOS and/ or NVRAM deletes configuration information. Be sure to properly[...]

Component ident ification 13 D rive LED defini tions Item LED Status Definition 1 Locate Solid blu e The drive is bei ng identified b y a host app lication. Flashing blue The drive carrie r firmware is be ing updated or requires an u pdate. 2 Activity ring Rotat ing green Drive a ctivity Off No drive activit y 3 Do not remove S olid white Do not re[...]

Component ident ification 14 • Cache module install ed on a storage controller • Cache modul e installed on th e system b oard 1 - Amber 2 - Green 3 - G reen Interpre tation Off Off Off The cache module is not powered. Off Flashing 0.5 Hz Flashing 0.5 Hz The cache micr ocontroller is e xecuting from w ithin its boot loader an d receiving ne w f[...]

Component ident ification 15 1 - Amber 2 - Green 3 - G reen Interpre tation Flashing 2 Hz Flashing 2 Hz Off The capacitor pac k is not attached. Flashing 2 Hz Flashing 2 Hz On The cap acitor has be en charging for 10 minu tes, but has not reache d sufficient cha rge to perform a full backup. On On Off The current backup is complete, but power fluct[...]

Operations 16 Oper ati ons P ower up the server 1. Connect ea ch power cord to the server. 2. Connect each power cord to the power source. 3. Press the Power On/Standby button. The ser ver exits standb y mode and app lies full power to the sy stem. The system power LED changes from amber to gree n. P ower down the server Before powering down the se[...]

Operations 17 IMPORTANT: The requirement of ex tending or rem oving the server from the rack wh en performing insta llation and maintenanc e proced ures depends on the rail system used: • If using a ball - bearing rail system, you can pe rform most instal lations and maintenance by simply extending the server from the rack. • If using a frictio[...]

Operations 18 IMPORTANT: The requirement of ex tending or rem oving the server from the rack wh en performing installation and maintenance procedures depends on the rail sys tem used: • If using a ball - bearing rail system, you can pe rform most instal lations and maintenance by simply extending the server from the rack. • If using a friction [...]

Operations 19 a. Disconnect eac h power cord from th e power source. b. Disconne ct each power cor d from the server. 3. Do one of the followin g: o Extend the server from the rack (on pag e 16 ). o Remove the s erver from t he rack (on page 17 ). 4. Open the locking latch, slide the access panel to the rear o f the chassis, and then remove the acc[...]

Operations 20 7. Lift the PCI r iser cage to unsea t the riser board s. I nstall the PCI ri ser cage CAUTION: To prevent damag e to the server or e xpansion boards, power down the server, and disconnect all power cords before removi ng or installing the PCI riser cage. 1. Align the riser boards with the corresponding connectors on the system board,[...]

Setup 21 Setup O ptional installa tion services Delivered b y experienced, certified engin eers, HP Care Pack services help y ou keep your serve rs up and running with support packages tailored specifically for HP ProLiant systems. HP Care Packs let you integrate both hardware and so ftware suppor t into a single package. A number of service leve l[...]

Setup 22 S pace and airflow requirements To allow for servicing a nd adequate airflow, observ e the following spa ce and airflow requireme nts when deciding where to insta ll a rack: • Leave a minimum cl earance of 63.5 cm (25 inches ) in front of the rack. • Leave a minimum clear ance of 76.2 cm (30 i nches) behind the rack. • Leave a minimu[...]

Setu p 23 P ower require ments Installation of this eq uipment must comply wit h local and regional electri cal regulations governin g the installation of information technology equipment by licensed elec tricians. This equipment is designed to operate in insta llations covered by NFPA 70, 1999 Edition (Nationa l Electric Code) and NFPA - 75, 1992 [...]

Setup 24 WARNING: To reduce the risk o f electric sho ck or energy hazard s: • This equipment must be i nstalled by trained service personnel, as defined by t he NEC and IEC 60950 - 1, Second Ed ition, t he standard for Safety of Information Technology Equipment. • Connect the equipment to a reliably grounded SELV source . An SELV source is a s[...]

Setup 25 WARNING: This server is ver y heavy. To reduce t he risk of persona l injury or da mage to the equipment: • Observe local oc cupational health and safe ty requirements and g uidelines for manual material handling. • Get help to lift and stabilize the product during in stallation or removal, especially when the product is not fas tened [...]

Setup 26 WARNING: When insta lling a server in a telco rack, be sure that th e rack frame is a dequately secured at the top and bottom to the bui lding structure. I dentifying the c ontents of the server sh ipping carton Unpack the server shipping carton and locate the materials and documentation necessary for installing the server. All the rack mo[...]

Setup 27 CAUTION: Always plan the rack ins tallation so that the heaviest item is on the bottom of the rack. Install the heaviest item first, and continue to popu late the rack from the bottom to the top. To install the server in an HP, Compaq - brande d, Telco, or thir d pa rty rack: 1. Install the server and cable management arm option into the r[...]

Setup 28 To operate properly, the server mus t have a supported operating system. For the latest information on operating sy stem support, s ee the HP website ( http://www.hp.com/go/supportos ). To install an operating system on the server, use one of the following methods: • Intelligent Prov isioning — The iLO Management Engine is a new fe atu[...]

Hardware options installation 29 H ar d w ar e optio ns ins tallati on Introduction If more than one opt ion is being installed, read the installation instr uctions for all the hard ware options and identify simila r steps to streamline the ins tallation process. WARNING: To reduce the risk o f personal inj ury from hot surfa ces, allow the d rives[...]

Hardware options installation 30 2. Connect the front video adapter to the video devic e. To remove the front video a dapter, squeeze the top and bottom to gether to release the lock ing mechanism. D rive options The embedded stor age controller support s SATA drive installation. F or SAS drive installation, in stall the storage controller card and[...]

Hardware options installation 31 • Populate drive bays , based on the drive numbe ring sequence. Start fro m the drive bay with the lowes t device number (" Drive nu mbering " on page 12 ). • When drives are gr ouped together into the same drive array, they m ust be of the same c apacity to provide the gr eatest storag e space efficie[...]

Hardware options installation 32 4. Determin e the status of the d rive from the driv e LED definitions (on page 13 ). D rive cab le options Two- port SATA cable option When this cable option is installed i n the eight - bay drive cage, the se rver supports the six - drive SATA configuration. In this configuration, drive bays 1 thro ugh 6 are popul[...]

Hardware options installation 33 d. Route the cable along the side of the system board towards the front chassis, and then connect the cable to the dri ve backplane. 8. Connect the rest of the drive cables required in this drive co nfiguration. For more information, see " Storage cabling (on pag e 70 )." 9. Install the PCI riser cage (on [...]

Hardware options installation 34 6. Connect the Mini - SAS cable to the storage controll er. 7. Install the storage controller (" Installing a storage contr oller " on page 37 ). 8. In the four - bay LFF drive cage config uration, route the Mini - SAS ca ble along the si de of the system board towards the front chassis, and then connect t[...]

Hardware options installation 35 o Four - bay LFF drive cage with Mini - SAS cable connect ed to the low - profile slot 9. In the four - bay LFF drive cage configuratio n, HP recommends securing th e excess length of the 890 mm Mini - SAS cable by usi ng the cable clip that came with the kit: a. Use the two vertical dash marks in front of the fan c[...]

Hardware options installation 36 o Eight - bay SFF drive cage with Mini - SAS cables connected to the full - he ight slot o Eight - bay SFF drive cage with Mini - SAS cables connected to the low - profile slot 11. Connect the rest of the drive cables required in this drive co nfiguration. For more information, see " Storage cabling (on pag e 7[...]

Hardware options installation 37 C ontroller options The server ships wit h an embedded Smart Array B120i controller. For m ore information about the cont roller and its featur es, see the HP Dynamic Smart Array RAID Contr oller User Guide on the HP website ( http://www.hp.com/suppor t/DSA_RAID_UG_en ). To configure ar rays, see the Configuring Arr[...]

Hardware options installation 38 a. Disconnect ea ch power cord from the power sour ce. b. Disconne ct each power cor d from the server. 3. Do one of the followin g: o Extend the server from the rack (on pag e 16 ). o Remove the s erver from the rack (on page 17 ). 4. Remove the a ccess panel (on page 18 ). 5. Install the storage controll er ("[...]

Hardware options installation 39 6. Connect the capacitor pac k cable to the c ache module. 7. Do one of the followin g: o When using the embedded array controller, install the cache module on the syste m board, and then install the PCI riser cage (" Install the PCI riser cage " on page 20 ). o When using an integrated array controller, i[...]

Hardware options installation 40 8. Route the capacitor pack cable towards the front chassis. For more infor mation on capacitor pack c abling in different driv e configurations, se e " S torage cabling (on page 70 )." 9. Install the capacito r pack: a. Insert the cable end of the capacitor pack in the hol der. b. Press the op posite end [...]

Hardware options installation 41 o Four - bay LFF drive model o Eight - bay SFF drive mode l 5. Remove the a ccess panel (on page 18 ). 6. Remove the P CI riser cage (on page 19 ). 7. If you are install ing the optical drive in an LFF driv e model, do the following:[...]

Hardware options installation 42 a. Thread the optical dri ve cable through the optical drive bay. b. Connect the cable to the optical drive. 8. Install the optical drive into the bay, and then secure it with the screw: o Four - bay LFF drive model[...]

Hardware options installation 43 o Eight - bay SFF drive mode l 9. If you are inst alling the optical drive in an SFF drive mo del, connect the opti cal drive cable to the optical drive. 10. Route the optical drive cable along the s ide of the system board, and then connect the cable to the system board: o Four - bay LFF drive model[...]

Hardware options installation 44 o Eight - bay SFF drive mode l 11. Install the PCI riser cage (on page 20 ). 12. Install the access panel (on page 19 ). 13. Install the server into the rack (" Installing the se rver into the rack " on pag e 26 ). 14. Po wer up the serv er (on page 16 ). H ot - plug fan module option To provide su fficien[...]

Hardware options installation 45 In a redundant fan mode : • If one fan rotor fails, the system c ontinues to operate without redundancy. This condition is indicated by a flashing amber He alth LED. • If two fan rotors fail, t he system shuts dow n. I nstalling a hot - plug fan module if the server is installed in a ball- bearing rail system wi[...]

Hardware options installation 46 o Remove the defective fan in a failed redundant fan conf iguration. 5. Install the fan module into the fan bay. 6. Install the access panel (on page 19 ). 7. Slide the server bac k into the rack . 8. If the fan installation was made to upgrade the server from a nonredundant to a redundant fan mode, reboot the ser v[...]

Hardware options installation 47 a. Disconnect each power cord from the p ower source. b. Disconne ct each power cor d from the server. 3. Remove the s erver from the rack (on page 17 ). 4. Remove the a ccess panel (on page 18 ). 5. Do one of the followin g: o Remove the fan blank in a nonredundant configuration. o Remove the defective fan in a fai[...]

Hardware options installation 48 6. Install the fan module into the fan bay. CAUTION: To preve nt improper cooling and thermal damage , do not operate the server unles s all bays are popul ated with either a co mponent or a blank. 7. Install the access panel (on page 19 ). 8. Install the server into the rack (" Installing the se rver into the [...]

Hardware options installation 49 • Single - rank and dual - rank PC3 - 10600 (DDR - 1333) RDIMMs operating at up t o 1333 MT/s • Single - rank and dual - rank PC3 - 12800 (DDR - 1600) RDIMMs operating at up t o 1600 MT/s • Quad -r ank P C3L - 10600 (DDR3L - 1333) LRDIMMs op erating at up to 1333 MT/s Depending o n the processor mo del, the nu[...]

Hardware options installation 50 D IMM identification To determine DIMM characteristics, use the label attac hed to the DIMM and the following illus tration and table. Item Aspect Definition 1 Size — 2 Rank 1R = Single rank 2R = Dual rank 4R = Quad rank 3 Data width x4 = 4 bit x8 = 8 bit 4 Voltage rating L = Low voltage (1.35 V) U = Ultra low vol[...]

Hardware options installation 51 Dual - rank DIMMs provide the gre atest capacity with the existing memory technology. For example, if current DRAM technology supports 2 - GB single - rank DIMMs, a dual - rank DIMM would be 4 GB. M emory subsystem a rchitecture The memory subsystem in this se rver is divided into channels. Each proc essor supports [...]

Hardware options installation 52 Advanced ECC provide s additional prote ction over St andard ECC b ecause it is possibl e to correct certa in memory erro rs that would ot herwise be uncor rected and result in a server failur e. Using HP Adv anced Memory Error Detection technology, the server pro vides notification when a DIMM is degradi ng and has[...]

Hardware options installation 53 For detailed memory c onfiguration rules a nd guidelines, use the Online DD R3 Memory Configura tion Tool on the HP website ( http://www.hp.com/go/ddr3memory - configurator ). A dvanced ECC population guidelines For Advanced ECC mode c onfigurations, observe t he following guideline s: • Observe the gene ral DIMM [...]

Hardware options installation 54 • Each channel can have a different valid online spare configuration. • Each populated chann el must have a spare r ank: o A single dual - rank DIMM is not a valid configurati on. o LRDIMMs are treated as dual - rank DI MMs. P opulation orde r For Online Spa re memory mode confi gurations with a singl e processo[...]

Hardware options installation 55 After install ing the DIMMs, use RBSU (" HP ROM - Based Setup Utility " on page 82 ) to confi gure the memory protection mode. P rocessor option The server su pports single - processor and dual - processor operat ions. WARNING: To reduce the risk of perso nal injury from hot surfa ces, allow the d rives an[...]

Hardware options installation 56 5. Remove the h eatsink blank. CAUTION: The pins on the processor soc ket are very fragil e. Any damage to the m may require replacing the syst em board. 6. Open each of the processor locking levers in the order indicated, and the n open the processor retaining bracket.[...]

Hardware options installation 57 7. Remove the cl ear processor socket cover. Reta in the processor socket cover for future use. 8. Install the processor. Verify that the processor is fully seated in the proc essor r etaining bracket by visually inspecting t he processor installat ion guides on either side o f the processor. THE PINS ON THE SYSTEM [...]

Hardware options installation 58 CAUTION: Do not press down on the pr ocessor. Pressing down on the processor may caus e damage to the processor socket and the system board. Press onl y in the area indicated on the processor retain ing bracke t. 10. Press and hold th e processor retaining bracket in place, and then close each p rocessor locking lev[...]

Hardware options installation 59 c. Finish the installation by completely tightening the screws in the same sequence. 13. Locate the fan bays 1, 2, 3, and 4.[...]

Hardware options install ation 60 14. Remove the fa n blanks, if ne cessary. 15. Install the addition al fans included in the proces sor option kit. NOTE: A dual - processor configuration req uires all eight fans. Som e single - proces sor configurations might already have five fans popu lated. Store any unuse d fans as spares. 16. Install the acce[...]

Hardware options installation 61 CAUTION: To prevent damag e to the server or e xpansion boards, power down the server, and disconnect all power cords before removi ng or installing the PCI riser cage. CAUTION: To preve nt improper cooling and thermal damage , do not operate the server unless all expansion slo ts have either an expansion s lot cove[...]

Hardware options installation 62 supply might be requi red. For more informat ion, see the HP Enterprise Configurator website ( http://h300 99.www3.hp.com/confi gurator/ ). For more inf ormation on estimation of power consum ption and proper se lection of com ponents, see th e HP Power Advisor websi te ( http://www.h p.com/go/hppoweradv isor ). To [...]

Hardware options installation 63 8. Install the graphics card retaining bracket. 9. Connect the graphics card power cable to th e graphics card. 10. Install the PCI riser cage (on page 20 ).[...]

Hardware options installation 64 11. Co nnect the other end of the graphics card power cable to the system board. 12. Install the access panel (on page 19 ). 13. Install the server into the rack (" Installing the se rver into the rack " on pag e 26 ). 14. Power up th e server (on page 16 ). H P Trusted Platform Modu le option Use these in[...]

Hardware options installation 65 • Any attempt to remove an insta lled TPM from th e system board breaks or disfigur es the TPM secur ity rivet. Upon locat ing a broken or disfigur ed rivet on an installed T PM, administrators should consider the system compromised and t ake appropriate meas ures to ensure th e integrity of the sys tem data. • [...]

Hardware options installation 66 6. Install the TPM board. Press dow n on the connector to seat the board (" System board components " on page 10 ). 7. Install the TPM security rivet by pressing the rivet fi rmly into the system board. 8. Install the PCI riser cage (on page 20 ). 9. Install the access panel (on page 19 ). 10. Install the [...]

Hardware options installation 67 • Always store the re covery key/password in multiple locations. • Always store copies of the rec overy key/passw ord away from t he server. • Do not save the recovery key/password on the encrypted hard drive. E nabling the Trusted Platform Module 1. When prompted during the start - up sequence, access RBSU by[...]

Hardware options installation 68 To install the component: 1. Unfasten the cable manag ement solutio n to access the power supply bays. 2. Remove the E MI shield from the power supply b ay 2. 3. Remove the protective cover from the connector pins on the powe r supply. WARNING: To reduce the risk of electric shock or damage to the equipment, do not [...]

H ardware options installation 69 4. Install the redundant power supply into the bay until it clicks. 5. Connect the power cord to the power supply. 6. Use the strain relief clip fro m the server har dware kit to secure t he power cord. 7. Route the power cord through the cable management solution. 8. Connect the power cord to the power source. Be [...]

Cabling 70 C abling C abling overview This section provides guidelines that help you make informed decisions about c abling the server and hardware options to optimize performance . For information on cabling peripheral comp onents, refer to the white pa per on high - density deployment at the HP website ( http://www.hp.com/products/servers/platfor[...]

Cabling 71 • Four - bay LFF drive cage connec ted to the SAS - enabled rise r board Item Description 1 Power cable 2 Capacitor pack cabling 3 560 mm Mini - SAS cable • Four - bay LFF drive cage connec ted to a controller in the full - height expansion slot Item Description 1 Power cable 2 Capacitor pack cable 3 890 mm Mini - SAS cable[...]

Cabling 72 • Four - bay LFF driv e cage connected to a controller in the low - profile expan sion slot Item Description 1 Power cable 2 Capacitor pack cable 2 890 mm Mini - SAS cable E ight - bay SFF drive cabling • Six - drive SFF SATA configuration Item Description 1 Power cable 2 Capacitor pack cable 3 Two- port SATA cabl e 4 700 mm Mini - S[...]

Cabling 73 • Eight - bay SFF drive c age connected to the SAS - e nabled riser board Item Description 1 Power cable 2 Capacitor pack cable 3 560 mm Mini - SAS cable 4 700 mm Mini - SAS cable • Eight - bay SFF drive cage conn ected to the P822 controller in the full - height expansion slot Item Description 1 Power cable 2 Capacitor pack cable 3 [...]

Cabling 74 • Eight - bay SFF drive cage conn ected to the P420 controller in the full - height expansion slot Item Description 1 Power cable 2 Capacitor pack cable 3 560 mm Mini - SAS cable 4 700 mm Mini - SAS cable • Eight - bay SFF drive cage conn ected to the P420 controller in low - profile expansion slot Item Description 1 Power cable 2 Ca[...]

Cabling 75 O ptical driv e cabling • Optical drive cabl ing in the four - bay LFF drive cage • Optical drive cabl ing in the eight - bay SFF drive cage[...]

Cabling 76 G PU power cabli ng • Graphics card conn ection • System board connection[...]

Software and conf iguration util ities 77 S o f t w ar e and conf i gur atio n utiliti e s Server mode The software and configurati on utilities presented in this secti on operate in online mode, offline mode, or in both modes. Software or configurat ion utility Serve r mode HP iLO (on page 77 ) Online and Offline Active Health System (on page 78 )[...]

Software and conf iguration util ities 78 iLO enables and manage s the Active Health System (on page 78 ) and also featur es Agentless Ma nagement. All key intern al subsystems a re monitored by iLO. SNMP alerts a re sent directly by iLO regardless of the hos t operating sy stem or even if n o host operating sy stem is installed . HP Insight Remote[...]

Software and conf iguration util ities 79 The data that is collected is manag ed according to the HP Data Privac y policy. For more information see the HP website ( http :/ /www.hp.com/go/priv acy ). The Active Health System log, in c onjunction with the system monitoring provided by A gentless Management or SNMP Pass - thru, provides continuous mo[...]

Software and conf iguration util ities 80 H P Insight Diagnostics HP Insight Diagnostic s is a proactive server management tool, available in both offline and online version s, that provides diag nostics and troublesh ooting capabilities to assist IT adminis trators who verify serve r installations, tro ubleshoot problems, and pe rform repair valid[...]

Software an d configura tion utilities 81 H P Insight Remote Suppor t software HP strongly recommends that you install HP Insight Remote Suppor t software to complete the installation or upgrade of your produc t and to enable enhanced delivery of you r HP Warranty, HP Care Pack Service, or HP contractual support agreement. HP Insight Remote Support[...]

Software and conf iguration util ities 82 HP Service Pack for Pro Liant SPP is a release set t hat contains a com prehensive colle ction of firmwa re and system softwa re components , all tested tog ether as a singl e solution stack fo r HP ProLiant ser vers, their opti ons, BladeS ystem enclosures, and limited HP external storage. SPP has several [...]

Software and conf iguration util ities 83 • Configuring memory optio ns • Language sel ection For more informat ion on RBSU, see the HP ROM - Based Setup Utilit y User Guide on the Documentation CD or the HP website ( http://www.hp.com/support/rbsu ). U sing RBSU To use RBSU, use the foll owing keys: • To access RB SU, press the F9 key during[...]

Software and conf iguration util ities 84 Bo ot options Near the end of the boot proces s, the boot option s screen is displa yed. This scr een is visible for several seconds before the system attempts to boot from a su pported boot de vice. During this time, you can do the following: • Access RBSU b y pressing the F9 key. • Access Intelligent [...]

Software and conf iguration util ities 85 U tilities an d features A rray Configuration Utility ACU is a utility with the following features: • Runs as a loc al application or re mote service accesse d through the HP Sys tem Management Ho mepage • Supports online array capacity expansion, logical drive exte nsion, assignment of online spares, a[...]

Software and conf iguration util ities 86 O ption ROM Config uration for Arrays Before installin g an operating system, you can u se the ORCA utility to creat e the first logical drive, assign RAID levels, and es tabli sh online spare configuration s. The utility also p rovides support for the fol lowing functions: • Reconfiguring one or more log[...]

Software and conf iguration util ities 87 Legacy USB support pro vides USB functionality in e nvironments where USB su pport is not available no rmally. Specifically, HP provides legacy USB functional ity for the following: • POST • RBSU • Diagnostics • DOS • Operating environ ments which do not provi de native USB support R edundant ROM [...]

Software and conf iguration util ities 88 Software and firmware Software and firmware shou ld be updated b efore using the serv er for the first tim e, unless any ins talled software or components requ ire an older version. Fo r system software and firmware u pdates, download the SPP (" HP Service Pack for ProLiant " on page 82 ) from the[...]

Troubleshootin g 89 T r ou blesho oting T roubleshooting resources The H P ProLiant Gen8 Troubleshooting Guide, Vo lume I: Troubleshooting provid es procedures for re solving common problems an d comprehensive cours es of action for fault isolat ion and identification, issue resolution, and software maintenan ce on ProLiant server s and server blad[...]

System battery replacement 90 S y st em batter y r eplacement If the server no longer au tomatically displays the correct date and time, you might have to replace the battery that provides powe r to the real - ti me clock. Under normal use, battery life is 5 to 1 0 years. WARNING: The compu ter contains an internal l ithium manganese dio xide, a va[...]

System battery replacement 91 IMPORTANT: Replacing the syst em board batter y resets the system RO M to its default configuration. After replacing the battery, rec onfigure the system through RBSU. To replace th e component, rev erse the remova l procedure. For more information about battery replace ment or proper dis posal, contact an autho rized [...]

Regulatory comp liance notices 92 R egulator y com pliance n oti ce s R egulatory comp liance identi fication n umbers For the purpose of regulato ry compliance certificati ons and identification, t his product has been assigned a unique regulatory mo del number. The regul atory model number can be fo und on the produc t nameplate label, along with[...]

Regulatory comp liance notices 93 radio communicat ions. However, ther e is no guarantee that interfe rence will not occur in a pa rticular installation. If this equipment does caus e harmful interference to radi o or television recept ion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the int[...]

Regulatory comp liance notices 94 This Class A digital apparatus meets all requirements of th e Canadian Interference - Causing Equipment Regul ations . Cet appareil numé rique de la classe A respec te tout es les exigen ces du Règlemen t sur le matéri el brouilleur du Canada. Class B equipment This Class B digital apparatus meets all requiremen[...]

Regulatory comp liance notices 95 This symbol on the product or on its packaging indicates that this product must not be disposed of with your other househ old waste. Instead, it is your re sponsibility to dispose o f yo ur waste equipment by handin g it over to a designated collection p oint for the recycling of wast e electrical and electronic eq[...]

Regulatory comp liance notices 96 K orean noti ce Class A equipment Class B equipment C hinese notice Class A equipment Vietnam complia nce marking no tice This marking is for app licable products only. Ukraine not ice[...]

Regulatory comp liance notices 97 L aser compl iance This product may be pro vided with an optic al storage device ( that is, CD or DVD drive) and/or fiber optic transceiver. Each of these devices con tains a laser tha t is classified as a Class 1 Laser Prod uct in accordan ce with US FDA regulation s and the IEC 60825 - 1. The product does not emi[...]

Regulatory comp liance notices 98 P ower cord statement for Jap an A coustics statement for Germany (Geräuschemission) Schalldruckpegel L pA < 70 dB(A) Zuschauerpositione n (bystander positions), Nor maler Betrieb (normal ope ration) Nach ISO 7779:1999 ( Typprüfung)[...]

Electrostatic dis charge 99 E lectr os tati c disc har ge P reventing elect rostatic d ischarge To preven t damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricit y from a finger or other cond uctor may damage system boards or other stat ic - sensitiv e devi[...]

Specifications 100 S pec if icati ons E nvironmental spec ifications Specification Value Temperature range* Operating 10 ° C to 35 ° C (50 ° F to 95 ° F) Nonoperating - 30 ° C to 60 ° C ( - 22 ° F to 14 0 ° F) Relative humidity (noncondensing) Operating, maximum wet bul b temperature of 28°C (82.4°F) 10% to 90% Nonoperating, maximum wet b[...]

Specifications 101 H P 460 W CS power supply (92% eff iciency) Specification Value Input requirements — Rated input voltage 100 V AC – 240 V AC Rated input frequency 50 Hz or 60 Hz Rated input current 6 A – 3 A Rated input po wer 526 W at 100 V AC input 505 W at 200 V AC input Btus per hour 1794 at 100 V AC input 1725 at 200 V AC inpu t Power[...]

Specifications 102 Rated input cu rrent 9 A – 4.5 A Rated input po wer 857 W at 100 V AC input 824 W at 200 V AC input Btus per hour 2925 at 100 V AC inpu t 2812 at 200 V AC inpu t Power supply output — Rated steady - state power 750 W at 100 V to 120 V A C input 750 W at 200 V to 240 V A C input Maximum peak power 750 W at 100 V t o 120 V AC i[...]

Specifications 103 Rated input power (Btus per hour) 2780 at - 36 V DC input 2740 at - 48 V DC input, nominal input 2720 at - 72 V DC input Power supply output — Rated steady - state power (W) 750 W Maximum peak power (W) 750 W CAUTION: This equipment is designed to permit the connection of the earthed conductor of the DC supply circuit to the ea[...]

Specifications 104 input Maximum peak power 800 W at 100 V A C input 900 W at 120 V AC input 1200 W at 20 0 V to 240 V AC input H ot - plug power supply calculations For hot - plug power supply specification s and calculators to determin e electrical and heat loa ding for the server, ref er to the HP Enterprise Configurator website ( http://h30099.[...]

Support and other resources 105 S uppo r t and other r eso ur ces B efore you contact HP Be sure to have the follo wing information available before you call HP: • Active Health System log Download and have av ailable an Active Health System log f or 3 days bef ore the failure w as detected. For more infor mation, see the HP iLO 4 User Gu ide or [...]

Support and other resources 106 providers or service partners) identifies that the re pair can be acc omplished by the us e of a CSR part, HP wi ll ship that part directly to you for re placement. There are two categories of CSR parts: • Mandatory — Parts for which customer self repair i s mandatory. If you reque st HP to replace these pa rts, [...]

Support and ot her resources 107 Pour plus d'inform ations sur le programm e CSR de HP, contactez vot re Mainteneur Agrée loc al. Pour plus d'informat ions sur ce progr amme en Amériq ue du Nord, consu ltez le site Web HP ( http://www.h p.com/go/selfrepair ). R ipar a zi one da parte del c lie nt e Per abbreviare i te mpi di riparazione[...]

Support and other resources 108 HINWEIS : Einige Teile sind nicht für Customer Self Repair ausgele gt. Um den G arantieanspruch des Kunden zu erf üllen, muss da s Teil von einem H P Servicepartne r ersetzt werden . Im illustriert en Teilekatalog sind diese Tei le mit „No“ bzw. „Nein“ gekenn zeichnet. CSR - Teile werden abhä ngig von der [...]

Support and other resources 109 sustitucion es que lleve a ca bo el cliente, H P se hará cargo de todos l os gastos de env ío y devolución d e componentes y esco gerá la empresa de transpo rte que se utilice par a dicho se rvicio. Para obtener más i nformación acerca del pr ograma de Reparac iones del propio clien te de HP, póngase en contac[...]

Support and other resources 110 Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas pe ças também são proje tadas para o reparo feito pelo cliente. No entanto, s e desejar que a HP as substi tua, pode hav er ou não a cobrança de taxa adicional, depe ndendo do tipo de s erviço de garantia des tinado ao produto. OBSERVAÇÃ O:[...]

Support and other resources 111[...]

Support and other resources 112[...]

Acronyms and ab breviations 113 A c r on y ms and abbr e v iati on s ABEND abnormal end ACU Array Configuration U tility AMP Advanced Memory Protec tion ASR Automatic Server R ecovery BMC baseboard manageme nt controller BSMI Bureau of Standards, M etrology and Inspection CE Conformité Européenne (European Conformity) CS HE HP Common Slot High - [...]

Acronyms and ab breviations 114 DPC DIMMs per cha nnel EMI electromagnet ic interference FBWC flash - backed write cache FCC Federal Communications C ommission GPU graphics processin g unit HP SIM HP Systems Insight Manager HP SUM HP Smart Update Manag er IEC International Electrotechnical Commissi on iLO Integrated Lights - Out IML Integrated Mana[...]

Acronyms and ab breviations 115 NMI nonmaskable inte rrupt NVRAM nonvolatile memory ORCA Option ROM Conf iguration for Arrays PCIe peripheral compon ent interconnect express PDU power distribution unit POST Power - On Self Test PXE preboot execution env ironment RBSU ROM - Based Setup Utility RDIMM registered dual in - line memory mod ule RDP Rapid[...]

Acr onyms and abbrevi ations 116 SD Secure Digital SDDC Single Device Data Corr ection SELV separated extra low voltage SFF small form fact or SPP HP Service Pack for ProLiant STD standard (DIMM vo ltage) TMRA recommended ambient ope rating temperature TPM Trusted Platform Modu le UDIMM unregistered dua l in - line memory mo dule UID unit identific[...]

Documentation feedback 117 Doc ument ati on f eedbac k HP is committed to pro viding documentation that mee ts your needs. To help us improve the documentation, send any erro rs, suggestion s , or comments to Documentation Feedback ( mailto:docsfeedback@hp.co m ). Include the document title and part number, version number, or the URL when submittin[...]

Index 118 A AC power supply 101, 102, 103 access panel 18, 19 acoustics sta tement for Germany 98 ACU (Array Config uration Utility) 77, 85 Advanced ECC memor y 53, 84 airflow requir ements 21, 22 AMP (Advanced Memory Prote ction) 84 AMP modes 84 Array Configuration Utili ty (ACU) 85 ASR (Automatic Se rver Recovery) 86 authorized r eseller 105 auto[...]

Index 119 front video adapter 29 G graphics card cablin g 61 grounding method s 99 grounding requirem ents 23 H hard drive LEDs 13 hard drives, dete rmining status of 13 hard drives, inst alling 29, 30 hardware options 26, 29 hardware options in stallation 29 health driver 86 help re sources 105 hot - plug drive, insta lling 31 hot - plug fans 44, [...]

Index 120 power requirements 104 power supplies 101, 102, 103, 104 power supply 104 power supply outpu t 104 power supply specific ations 101, 102, 103, 104 powering down 16 powering up 16, 83 preparation procedu res 16 problem diagnosis 89 processo rs 55 R rack installation 21 rack reso urces 21 rack warnings 25 RBSU (ROM - Based Setu p Utility) 7[...]

Index 121 W warnings 25 website, HP 105[...]