Deutsch dropdown-ico

HP (Hewlett-Packard) 9315M Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung HP (Hewlett-Packard) 9315M an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von HP (Hewlett-Packard) 9315M, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung HP (Hewlett-Packard) 9315M die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung HP (Hewlett-Packard) 9315M. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung HP (Hewlett-Packard) 9315M sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts HP (Hewlett-Packard) 9315M
- Den Namen des Produzenten und das Produktionsjahr des Geräts HP (Hewlett-Packard) 9315M
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts HP (Hewlett-Packard) 9315M
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von HP (Hewlett-Packard) 9315M zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von HP (Hewlett-Packard) 9315M und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service HP (Hewlett-Packard) finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von HP (Hewlett-Packard) 9315M zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts HP (Hewlett-Packard) 9315M, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von HP (Hewlett-Packard) 9315M widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    Software release 07.8.04a supersedes earlier software releases in the 07. x software branch. (For information about software branches and minimum release requiremen ts for management module support, refer to “Software Branches” on page 3.) The 07.8.04a release notes pro vide in formation on the following items: • New hardware and software enh[...]

  • Seite 2

    Release Notes for 07.8.04a ii © Copyright 2001, 2008 Hewlett-Packard Develop- ment Comp any , L.P . The informatio n cont ained herein is subject to ch an ge without notice. Publication Number 5991-4722 September 2008 Applicable ProCurve 930 0 (Current) Products 9304M Routing Switch . . . . . . . . . . . . . . . . . . (J4139A) 9308M Routing Switch[...]

  • Seite 3

    iii Release Notes for 07.8.0 4a Content s Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Documentation for Software Relea s e 07.8.04a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Downloading th[...]

  • Seite 4

    1 Release Notes for 07.8.04 T er minology T erminology The following table defines basic product terms used in ProCurve routing switch documen tation. Product Document ation for So f tware Release 07.8.04a Software release 07.8.04a includes all of the features in release 07.8.00a , pl us several new features. • For documentation on the features i[...]

  • Seite 5

    Product Documentation for Softw are Release 07.8.04a Release Notes for 07.8.04 2 T able 1: Where T o Get More Information Title Content s Installation and Basic Configuration Guide • Installation • Basic F eatures • System (SNMP , SNTP , Syslog, br oadcast and multicast throttling) • Port configuration (speed, mode ) • Layer 2 (MAC table [...]

  • Seite 6

    3 Release Notes for 07.8.04 Downloading the Latest Software and Documentation Downloading the Latest So f tware and Documentation Y ou can download software version 07 .8 .04a and the late st routing switch product documentation from the ProCurve website as described below . T o Download a Software Version: 1. Go to the ProCurve website at http://w[...]

  • Seite 7

    Software Requirements for Management Modules Release Notes for 07.8.04 4 Sof tware Requirement s for Management Modules T abl e 3 shows the minimum software releases required to run redundant management mo dul es. T able 3: Minimu m Software Requir ements f or Management Modules 07.7.01b release Bug fixes, 07 .7.01 features and enhancements to exis[...]

  • Seite 8

    5 Release Notes for 07.8.04 Software S uppor ted on ProCur v e Routing Switches Sof tware Supported on Pr oCurve Routing Switches T abl e 4 shows the software releases s upporte d on each ProCurve routing switch. Boot Code Requirement s for ProCurve Sof tware T o run a software release on a ProCurve routing switch , you must u se the minimum versio[...]

  • Seite 9

    Boot Code Require ments f or ProCur v e Software Release Notes for 07.8.04 6 T able 5: Boot Code Requirements Routing Switch Modules Sof tware Image Minimum Boot Co de Required ProCurve 9304 M ProCurve 9308 M With one of the following M1 1 modules (without Redundant Management): J4141A 10/100 J4144A Gigabit SX J4146A Gigabit 4LX/4SX HPR06636.bin 2 [...]

  • Seite 10

    7 Release Notes for 07.8.04 Upgrading Software on an M2 , M4, or EP Management Module to Release 07.8.04a Upgrading Sof tware on an M2, M4 , or EP Management Module to Release 07.8.04a This section explains how to upgra de the software us ed on M2, M4, and EP redundan t management modules on a ProCurve 9304M, ProCurve 9308M, or ProCurve 9315M routi[...]

  • Seite 11

    Upgrading Software on an M2, M4, or EP Management Module to Release 07.8.04a Release Notes for 07.8.04 8 B. If the routing switch is running software EARLIER than rele ase 07.6.01b , copy release 07.6.01b to flash memory . Then reboot the device to load the 07.6.01 b software. C. Copy release 07.8.04a to fla s h me mory , and reboot the routing swi[...]

  • Seite 12

    9 Release Notes for 07.8.04 Upgrading Software on an M2 , M4, or EP Management Module to Release 07.8.04a is displayed when the flash images are synchro nized and the upgrade is complete. 4. V erify that the software has been successfully cop ied by entering the show flash command at any level of the CLI: • The software release in the pr imary fl[...]

  • Seite 13

    Using SNMP to Upgrade Software on a Management Module Release Notes for 07.8.04 10 5. Reboot the routing switch to load software release 0 7.8.04a from the area of flash memory (primary or secondary) where you stored it. NOTE: When you reload the software after upgrading the software to release 07.8.04a, the routing switch displays a message to say[...]

  • Seite 14

    11 Release Notes for 07.8.04 Upgrading th e FPGA on a 10 Gigabit Ethernet Module < tf tp-ip- addr > is the TFTP server ’ s IP address. < file-name > is the image file name. < command-integer> is one of the following values: 20 – Downloads the software code into the device’s primary flash area. 22 – Downloads the software c[...]

  • Seite 15

    Using Different Combinations of Management Mod ules Release Notes for 07.8.04 12 NOTE: The show flash command will list the new FPGA code versio ns but the new versions do not take effect until you reload the software. Using Different Combinations of Management Modules This section describe s the different combinations of M1, M2, M4, EP , and T -Fl[...]

  • Seite 16

    13 Release Notes for 07.8.04 Non-Redundant Management on ProCur ve 9304M and ProCur ve 9308M Routing Switches management module, and also do wnlo adable from t he ProCurve website (see “T o Downl oad Product Documentation:” on page 3). Non-Redundant Management on ProCurve 9304M and ProCurve 9308M Routing Switches Management modules without Redu[...]

  • Seite 17

    Removi ng a Module from an Ac tive De vice Release Notes f or 07.8.04 14 Removing a Module from an Active Device Before you remove a module from a routing switch in operation, first disable the module. Disabling the module before removing it prevents a brief service in terruption on other unmanag ed modules. The brief interruption can be caused by [...]

  • Seite 18

    15 Release Notes for 07.8.04 Enhancements and Configuration Note s in 07.8.03 Inserting or Removing an EP Module on a ProCurve 9315M NOTE: This section applies only to a ProCurve 93 15M (15-slot ch assis) with EP modules. Do not insert or remove EP modules in a ProCurve 9315M until the device has full y booted. General ly , bo oting takes around tw[...]

  • Seite 19

    Software Fix e s Release Notes for 07.8.04 16 Sof tware Fixes The fixes for software bugs found on ProCurve 9300M Seri es routing switches in software releases 07.8.00h through 07.8.03 are described in the following table. Software fixes are listed by bug ID for the software release in which th ey were imple mented. Bug ID Bug Descriptio n Protocol[...]

  • Seite 20

    17 Release Notes for 07.8.04 Software Fix es 45318 After you disable and swap a module, the active management module crash es. System 07.8.00 45319 When you enter the ip rebind-acl all command, the following message is logged: Exceed max DMA 9 L4 cam resource, using flow based ACL instead ACL 07.8.00 45415 SSH may reload if a diff erent client publ[...]

  • Seite 21

    Software Fix e s Release Notes for 07.8.04 18 48927 Port-based rate-limiting on outbou nd traf fic may not function properl y if a large output ra te is configured. Rate Limiting 07.8.00 07.8.00i 29031 In show ip nat trans command output, a maximum of 3000 Network Address T ranslation (NA T) sessions are displayed. NA T 07.8.00 29530 A write error [...]

  • Seite 22

    19 Release Notes for 07.8.04 Software Fix es 47395 If the primary link in an Link Aggregation Control Protocol (LACP) 802.3ad trunk go es down for more than 90 seconds and then comes back up, port flapping occurs. LACP 07.8.00 47826 The system rel oads when the ARP t able contains more entries than the configured maximum arp ta bl e value. System 0[...]

  • Seite 23

    Software Fix e s Release Notes for 07.8.04 20 50092 When you enter the no spee d-duplex command including speed and duplex at tributes, the specified fixed speed and duplex settin gs are not re moved. CLI 07.8.00 50203 A routing switch does not flush a MAC address on the Metro Ring Protocol (MR P). MRP 07.8.00 50347 Multicast forwarding is not supp[...]

  • Seite 24

    21 Release Notes for 07.8.04 Software Fix es 49218 LACP implementation caus es a trunk instance to be recreated if a primary tr unk port attached to a Cisco 6500 goes down or comes up. LACP 07.8.00 49294 If you do not enter the no rfc153 -compatibility command, type 3 summary link-state advertisements (LSAs) with maximum cost are sent. T o activate[...]

  • Seite 25

    Software Fix e s Release Notes for 07.8.04 22 52419 SSH disconnects an SSH client after the configured idle time expires even during an active SSH session. SSH 07.8.00 53721 A reload is performed due to the lack of memory allocated to the "vlan_router_int_list" pointer. VLAN 07.8.00 54207 A Data Access Exception reload in the cam_clear_dm[...]

  • Seite 26

    23 Release Notes for 07.8.04 Software Fix es 50323 802.1w is disabled i f you configure a topology gro up (802.1w in the master VLAN) and more VLANs than the configured s ystem-max spanning-tree value. VLAN 07.8.00 51621 A GBIC that is installed in an SFP slot, which is configured for the Simple Network T ime Protocol (SNTP) but has no cab l e at t[...]

  • Seite 27

    Software Fix e s Release Notes for 07.8.04 24 51933 A traffic flow is over-reporting the number o f outbound bytes transmitted as compared with the number of interface counters recorded by SNMP . SNMP 07.8.00 52074 When NA T and ACL are configured on the same interface, NA T does not translate packet s after you modify the ACL configuratio n. NA T [...]

  • Seite 28

    25 Release Notes for 07.8.04 Software Fix es 57594 The child route (more specific route) ages out from CAM before the parent route, resulting in blackholing of traffic. System 07.8.00 57774 A Data Access Exception crash occurs when a trunk is created with out entering the trunk deploy command and when the lead port is configured for 802.1w admin-pt[...]

  • Seite 29

    Software Fix e s Release Notes for 07.8.04 26 07.8.01 14668 Although rare in occurre nce, in some configurations with EBGP , IBGP , and OSPF routes, a routing switch may not always sele ct the best route. For example, the device might install an IBGP route in the routing table, even th ough th e IBGP route has a higher administrative distance than [...]

  • Seite 30

    27 Release Notes for 07.8.04 Software Fix es 29670 If you enable 802.1w ( spanning-tree command) on a port-based VLAN before configuring th e port as tagged or untagged, 802.1w fails to initialize. In addition, the show 8 02-1w command output shows that Rapid Sp anning Tree Protocol (RSTP) is not configured. Note that if you define the port as tagg[...]

  • Seite 31

    Software Fix e s Release Notes for 07.8.04 28 31084 On an EP 8 Port Mini-GBIC Redundant Management module, a system reload occurs when a BGP packet with an invalid header length is received. BGP4+ 07.8.01 31 157 A BGP routing switch fails to send notification after clearing a peer session. BGP4+ 07.8.01 31 166 OSPF fails to delete a redistributed s[...]

  • Seite 32

    29 Release Notes for 07.8.04 Software Fix es 32360 On an EP 48-Port 10/1000-TX RJ45 module, the routing switch does n ot successfully remove some ACL remarks and line entries from the configuration. This occurs if you delete an ACL (for example, no access-list 130 ) and then la ter create an ACL with the same ACL number (for example, access-list 13[...]

  • Seite 33

    Software Fix e s Release Notes for 07.8.04 30 3351 1 If a port in a trunk group goes down then comes up again, the routing switch incorrectly load balances traffic across the port s in the trunk group. In normal operation, the switch re-balance s the traffic so that all of the ports in the trunk group are properly utilized. Other 07.8.01 33834 The [...]

  • Seite 34

    31 Release Notes for 07.8.04 Software Fix es 34609 A 10 Gigabit Ethe rnet link stays up when the egress side of the link is disabled. No l ink-fault signal (LFS) is configured. 10GE link 07.6.06 07.8.01b 35199 When forwarding sFlow p acket s, the routing switch crashes with a data access exception in the “sw_12_get_outgoin g_port_by_da_match” r[...]

  • Seite 35

    Software Fix e s Release Notes for 07.8.04 32 46924 After a system reload, the sFlow sample command at the trunk configuration level is no longer supported. sFlow 07.6.06 07.8.01b 47724 The show ip bg p nei adv command output may not display all advertised routes. (This is a di splay issue only .) CLI 07.8.00 07.8.01b 47855 The following error mess[...]

  • Seite 36

    33 Release Notes for 07.8.04 Software Fix es 43721 After you install a 2-port 1-Gigabit Ethernet mo dule, the dm de lete < slot-number > command cau ses the routing switch to reload. 10GE link 07.6.05 07.8.01c 44138 CPU spikes occur for about 8 seconds when you add or remove ports with an outbound ACL on a VLAN. CPU, ACL 07.6.06 07.8.01c 4505[...]

  • Seite 37

    Software Fix e s Release Notes for 07.8.04 34 50592 Multicast jumbo packets are not supported on the 10 Gigabit Ethernet module. Multicast all 07.8.01c 51482 The system reload s when you enter the ip t f tp source loopback 19899960 command in config mode. This is because the V alid Port Range value is not checked. CLI 07.8.00 07.8.01c 07.8.01d 3440[...]

  • Seite 38

    35 Release Notes for 07.8.04 Software Fix es 54251 The debug 802.1w a ll_802_1W_events vlan command does not send output to a console, T elnet, or SSH session. 802.1d, CLI 07.8.00 07.8.01d 54375 A Data Access Exception crash occurs when you enter the no unt agged e thernet 21 ethernet 22 ethernet 23 e thernet 24 command after you enter the qos-tos [...]

  • Seite 39

    Software Fix e s Release Notes for 07.8.04 36 36440 The routing switch doe s not forward the MAC g roup address 01-80-C2-00-00-03 tha t was filtered by an IEEE 802.1D MAC bridge. MAC Addressing 07.8.02 38066 When you add a single, multicast static MAC address to a port that is a member of a VLAN may result in packet loss. MAC Addressing 07.8.02 382[...]

  • Seite 40

    37 Release Notes for 07.8.04 Software Fix es 47254 On an EP 8 Port Mini-GBIC Redundant Management module, when you configu re sFlow and an ACL so that packet s that were being forwarded by the CPU are filtered by the ACL, an incorrect VLAN ID is matched with the ACL. ACL 07.8.02 47542 A system reload may occur when you enter a show run command duri[...]

  • Seite 41

    Software Fix e s Release Notes for 07.8.04 38 49141 On an EP 8 Port Mini-GBIC Redundant Management module, you cannot reassign the same interfaces to an MRP ring. MRP 07.8.02 49240 On a 2-Port 10 Gigabit Ethernet module, when you configur e a jumbo MTU, p acket loss may result when a link on a 10 Gigabit port is re moved and re- inserted. System 07[...]

  • Seite 42

    39 Release Notes for 07.8.04 Software Fix es 54622 On an EP 8 Port Mini-GBIC Redundant Management module, a port in a virtual router interface on which an ACL is applie d was changed, added, or removed and the ACL was re-applied. This behavior may resu lt in a system reload. ACL 07.8.02 54724 Installing an EP 48-Port 10/1000-TX RJ45 module in one s[...]

  • Seite 43

    Software Fix e s Release Notes for 07.8.04 40 56399 When rate limiting is enabled , the ip rebind [ acl- num ] command does not function co rrectly and some ACL definitions are changed. ACL 07.8.02 56846 When an EP 8 Port Mini-GBIC Redundant Management module i s installed, if you configure the ip high-perf command on a ProCurve mo dule, the UDLD c[...]

  • Seite 44

    41 Release Notes for 07.8.04 Software Fix es 57758 On a network with OSPF Equal-Cost Multi-Path (ECMP) enabled, only the two next hops can be viewed when four next-hops exist. OSPF 07.8.02 57806 When you ente r the no port security command, all interface-level configurations are removed. Port Security 07.8.02 57847 On an EP 24 Port 100Base-FX modul[...]

  • Seite 45

    Software Fix e s Release Notes for 07.8.04 42 58868 Y ou cannot d isable the HP Discovery Protocol (FDP) or Cisco Discovery Protocol (CDP) on a secondary trunk port if you have entered the no f d p enable or no cdp enable command on a primary trunk port. FDP and CDP 07.8.02 58909 A route learned via RIPv1 disappears if a port in the RIPv1 route has[...]

  • Seite 46

    43 Release Notes for 07.8.04 Software Fix es 60395 Although a device has a route in the OSPF routing table, the device may add an IP cache entry that is flagged as "DI", meaning the packet destination is unknown. This problem occurs when you disa ble IP load-sharing. OSPF 07.8.02 60400 If you reconfigure OSPF by modifying hell o and dead [...]

  • Seite 47

    Software Fix e s Release Notes for 07.8.04 44 59468 If OSPF is configured, the OSPF configuration is not displayed in show ip osp f config command output until the c onfiguration is saved and the switch is reb ooted. OSPF 07.8.02 59698 If SSH is configured, a system re loa d sometime s occurs due to insufficient stack sp ace. SSH 07.8.02 59925 The [...]

  • Seite 48

    45 Release Notes for 07.8.04 Software Fix es 60916 T raffic is not evenly balanced on the members of a trunk after you enter the ip net-aggregate command and configure multislo t switch tru nks. IP Routing 07.8.02 60979 If BGP4 is configured and you enter the remove private-a s command on a neighboring device so that the routing switch receives an [...]

  • Seite 49

    Software Fix e s Release Notes for 07.8.04 46 62894 If the ports within a trunk are disabled due to a port security violation, the disable command is not displayed as part of the show ru nning-conf ig command output. Port Security 07.8.02 63138 On an interface on which both sFlow and an inbound ACL are configure d, in the display of sFlow traffic s[...]

  • Seite 50

    47 Release Notes for 07.8.04 Software Fix es 63975 A routing switch in which ProCurve 9300M Series modules are installed can someti mes reload due to incorrect logic fo r lockup detection. System 07.8.02 07.8.02d 62862 If RIP routes are conf igured and redistributed to OSPF , when an interface that is lea rning RIP routes is temporarily disabled, t[...]

  • Seite 51

    Software Fix e s Release Notes for 07.8.04 48 59279 If supernet routes are used and the IP Routing feature i s config ured, th e CAM entry of a child route sometimes gets aged out, l eaving the CAM entry of parent route programmed. This can cause misforwarding of traf fic. IP Routing 07.8.02 59502 A system reload is sometimes performed if the IP Ro[...]

  • Seite 52

    49 Release Notes for 07.8.04 Software Fix es 65342 When detecting a port lockup condition on a routing switch, a system reload may occur . System 07.8.02 65418 If you configure the Port Security feature with an ACL that permits Internet Control Message Protocol (ICMP) traffic, ICMP p acket s may sometimes be dropped. System 07.8.02 65740 If IGMP sn[...]

  • Seite 53

    Software Fix e s Release Notes for 07.8.04 50 65528 Removing a module from a ro uting switch may cause Port Database entries on the module to be inaccessible, resulting in a system reload. System 07.8.03 66003 After a module is removed from a routing switch, a syslog message is sometimes generated that lacks information to sufficiently describe the[...]

  • Seite 54

    51 Release Notes for 07.8.04 Software Fix es 69334 In a Switch/Router configured wi th outbound ACLs using the ip access-policy command, the L4 CAM entry is not programmed causing the packets to be forwarded via the Processor . ACL 07.8.03a 60525 In a Router configured with a rou ting protocol, occasionally the forwarding entry can point to an inva[...]

  • Seite 55

    Software Fix e s Release Notes for 07.8.04 52 07.8.03b 67638 Module: N/A Symptom: In a Switch or Router configured with the AAA authentication l ogin command using the line method keyword, all the available commands d o not appear with the CLI prompt. Resolution: Fixed in this release . AAA 07.8.03b 66617 Module: N/A Symptom: In a Switch or Router [...]

  • Seite 56

    53 Release Notes for 07.8.04 Software Fix es 73502 Module: N/A Symptom: In a Rout er co nf iguration wi t h ACL configured in flow mode, the sw itched packets with TCP SYN and ACK flag are incorrectly discarded. Resolution: Fixed in this release . L2 Forwarding 07.8.03b 70722 Module: 2404 Management Symptom: In a Router con figured with PIM, the un[...]

  • Seite 57

    Software Fix e s Release Notes for 07.8.04 54 74773 Module: N/A Symptom: In a Switch or Router configured with MAC Authenticati on, if when an authentica ted MAC moves from one port to another port, this can sometimes cause a system reset. Resolution: Fixed in this release . MAC Authentica-tion 07.8.03c 72954 Module: N/A Symptom: In a Router con fi[...]

  • Seite 58

    55 Release Notes for 07.8.04 Software Fix es 07.8.03d 76148 Module: N/A Symptom: In a Switch or Router configured with AAA and authentication using T A CACS+ server fo r user access through the Web Management interface, authentication requests after an unsuccessful login do not cease to be sent to the server . Resolution: Fixed in this release . AA[...]

  • Seite 59

    Software Fix e s Release Notes for 07.8.04 56 75878 Module: N/A Symptom: In a Switch or Router if the SSH is used for management, occasionally this can cause a system reset . Resolution: Fixed in this release . SSH 07.8.03d 76577 Module: N/A Symptom: In a Switch or Router configured with UDLD and Holddown Threshold, if the UDLD configured interface[...]

  • Seite 60

    57 Release Notes for 07.8.04 Software Fix es 77253 Module: N/A Symptom: In a Switch or Router running 07.8.03e and 07.8.03d, an ACL configure d with Rate Limit can occasionally cause high CPU usage due to traffic that is incorrectly coming to CPU. This problem does not exist in patches prior to 07.8.03d. Resolution: Fixed in this release . ACL 07.8[...]

  • Seite 61

    Software Fix e s Release Notes for 07.8.04 58 36440 Module: N/A Symptom: The Switch or Router forwards the packet with Destinat ion MAC address of 01:80:c2:00:00:0x. Thes e p acket s should be discarded. Resolution: Fixed in this release . Layer 2 07.8.04a 81853 Module: N/A Symptom: The switch or router incorrectly floods the Multicast packets to t[...]

  • Seite 62

    59 Release Notes for 07.8.04 Known Issues in 07.8.03 Known Issues in 07.8.03 This section lists the known issues in software release 07.8.03. ProCurve 9300M Series Modules T abl e 9 list s the modules that are currently available for use in Pro Curve 930 0M Series routing switches. (Discontinued modules are also listed.) 82608 Module: N/A Symptom: [...]

  • Seite 63

    ProCur v e 9300M Series Modules Release Notes for 07.8.04 60 T able 9: ProCurve 9300M Series Modules Module T ype Part Number and Description Module S tring EP Redundant Management Modules J4885A ProCurve 9300 EP 8-Port Mini-GBIC Redundant Management Module EP-8-port-mini-GBIC-management EP Non-Management Modules J4881B ProCurve 9300 EP 48-Port 10/[...]

  • Seite 64

    61 Release Notes for 07.8.04 ProCur v e 9300M Series Modules Unmanaged Mo dul es (S tandard, non-EP) J4140A ProCurve 9300 10/100 Modul e (24-port) 24-port-copper-module Discontinued J4142A ProCurve 9300 100Base FX Module (24-port MT -RJ) 24-port-100fx-module Discontinued J4143A ProCurve 9300 Gigabit SX Module (8-port) 8-port-gig-module Discontinued[...]

  • Seite 65

    ProCur v e 9300M Series Modules Release Notes for 07.8.04 62 —This page intentionally left blank—[...]

  • Seite 66

    63 Release Notes for 07.8.04 ProCur v e 9300M Series Modules 5991-4722 September 2008 © Copyright 2001, 2008 Hewlett-Packard Devel opment Company , L.P . The information contained herei n is subject to change without notice.[...]