HP (Hewlett-Packard) BL495c Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung HP (Hewlett-Packard) BL495c an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von HP (Hewlett-Packard) BL495c, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung HP (Hewlett-Packard) BL495c die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung HP (Hewlett-Packard) BL495c. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung HP (Hewlett-Packard) BL495c sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts HP (Hewlett-Packard) BL495c
- Den Namen des Produzenten und das Produktionsjahr des Geräts HP (Hewlett-Packard) BL495c
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts HP (Hewlett-Packard) BL495c
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von HP (Hewlett-Packard) BL495c zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von HP (Hewlett-Packard) BL495c und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service HP (Hewlett-Packard) finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von HP (Hewlett-Packard) BL495c zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts HP (Hewlett-Packard) BL495c, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von HP (Hewlett-Packard) BL495c widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    HP Pr oL iant BL4 9 5c Gener a ti on 5 Serv er Blade Maint enance and Se r v i ce Gui de Part Number 491031-004 April 2009 (Fourth Edition)[...]

  • Seite 2

    © Copyright 2008, 2009 Hewlett-Packard Develop ment Company, L.P. The information contained herein is subject to chan ge without no tice. The only warranties for HP products and services a re set forth in the express warranty statements accompanying such produc ts and services. Noth ing herein should be construed as constituti ng an additional w a[...]

  • Seite 3

    Con t e nt s Customer se lf re pair ...................................................................................................................... 5  Parts only warr anty service .................................................................................................... ..................... 5  Illustrated pa rts cata log ...[...]

  • Seite 4

    External USB fu nctional ity ..................................................................................................... .......... 49  Component iden tifica tion ....................................................................................................... ...... 50  Front panel compon ents ................................[...]

  • Seite 5

    C u st omer self r e pair HP products are designed with many Customer Self Repair (CSR) parts to minimi ze repair time and allow for greater flexibility in performing def ective parts re placement. If during the di agnosis period HP (or HP service providers or service partners) iden tifies that the repair can be accomplished by the use of a CSR par[...]

  • Seite 6

    • Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièces, les coûts de déplac ement et main d'œuvre du service vous seront facturés. • Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également conçues pour [...]

  • Seite 7

    NOTA: alcuni componenti HP non sono progettati per la ri parazione da parte del cl iente. P er rispe ttare la garanzia, HP richiede che queste parti siano sostituite da un c entro di assistenza autorizzato. Tali parti sono identificate da un "No" nel Ca talogo illustrato dei componenti. In base alla disponibilità e alla località geograf[...]

  • Seite 8

    anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materiali en, die mit einem CSR- Ersatzteil geliefert werden, könn en Sie entnehmen, ob das defekte Teil an HP zurückgeschickt werden muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzu schicken, müssen Sie dies inner halb eines vorgegebenen Zeitraums tun, in der [...]

  • Seite 9

    Centro de asistencia técnica de HP y reci birá ayu da telefónica por parte de un técnico. Con el envío de materiales para la sustitución de componente s CSR, HP especificará si los comp onentes defectuosos deberán devolverse a HP. En aquellos casos en los que sea necesario devolver algún componente a HP, deberá hacerlo en el periodo de ti[...]

  • Seite 10

    periode, gewoonlijk vijf (5) werkdagen, retourne ren aan HP. Het defecte onderdeel moet met de bijbehorende documentatie worden geretourneerd in het meeg eleverde verpakkingsmateriaal. Als u h et defecte onderdeel niet t erugzendt, kan HP u voor het vervangende onderdeel kosten in rekeni ng brengen. Bij reparatie door de klant betaal t HP alle verz[...]

  • Seite 11

    Se r v iço de gar anti a ape nas par a peças A garantia limitada da HP pode incluir um serviço de garantia apenas para peças. Segundo os termos do serviço de garantia apenas para peças, a HP fo rnece as peças de reposição sem cobrar nenhuma taxa. No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP su[...]

  • Seite 12

    Customer self repair 12[...]

  • Seite 13

    Customer self repair 13[...]

  • Seite 14

    Customer self repair 14[...]

  • Seite 15

    Customer self repair 15[...]

  • Seite 16

    Illus tr at ed par ts catalog Server blade components Item Description Spare part number Customer self repair (on page 5 ) 1 Access panel 490819-001 Mandatory 1 2 Processors — — a) 2.3-GHz AMD Opteron™ Mod el 2356** 448035-001 Optional 2 b) 2.1-GHz AMD Opteron™ Mode l 2352* ** 448033-001 Optional 2 c) 1.9-GHz AMD Opteron™ Model 234 7 HE* [...]

  • Seite 17

    Item Description Spare part number Customer self repair (on page 5 ) f) 2.4-GHz AMD Opteron™ Model 237 8* ** 500514-001 Optional 2 g) 2.3-GHz AMD Opteron™ Mode l 2376 HE* ** 515187-001 Optional 2 h) 2.9-GHz AMD Opteron™ Mod el 2389* ** 534249-001 Optional 2 i) 2.8-GHz AMD Opteron™ Model 238 7* ** 534250-0 01 Optional 2 j) 2.5-GHz AMD Optero[...]

  • Seite 18

    Item Description Spare part number Customer self repair (on page 5 ) j) QLogic QMH406 2 1GbE iSCSI BL-c Ada pter 488081-001 Mandatory 1 10 Hardware and pla stics kit 490818-001 Mandatory 1 a) Processor blank* — — b) DIMM baffle — — c) Battery tray* — — d) System connector cover* — — e) Processor cage* — — f) Server blade handle*[...]

  • Seite 19

    2 Optional: Optional—Teile, für die das Customer Self Repa ir-Verfahren optional ist. Diese Teile sind auch für Customer Self Repair ausgelegt. Wenn Sie jedoch den A ustausch dieser Teile von HP vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche Kosten anfallen. 3 No:[...]

  • Seite 20

    Illustrated parts catalog 20[...]

  • Seite 21

    R emo v al and r eplacement pr ocedur es Required tools You need the following item s for some procedures: • T-15 Torx screwdriver (provided inside the access panel) • Flathead screwdriver • HP Insight Diagnostics softw are (" HP Insight Diagnostics " on page 47 ) e removing them from their containers. • Always be properly grounde[...]

  • Seite 22

    CAUTION: When performing non-hot-plug operatio ns, you must power down the server blade and/or the system. However, it may be necessar y to leave the server blade powered up when performing other operations, such as hot-plug instal lations or troubleshooting. Symbols on equipment The following symbols may be placed on equipment to indicate the pres[...]

  • Seite 23

    Power down the server blade Before powering down the server blade for any up grade or maintenance procedures, perform a backup of critical server data and programs. Depending on the Onboard Administrator configuration, use one of the following methods to power down the server blade: • Use a virtual power button selection through iLO 2. This metho[...]

  • Seite 24

    3. Remove the server blade. 4. Place the server blade on a flat, level work surface. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent damage to electrical components, properly gr ound the server blade before beginning any installat[...]

  • Seite 25

    5. Disconnect the hard drive cables. 6. Remove the hard drive. 7. Disconnect the hard drive cables from th e hard drive. Retain for future use. To replace the component, reverse the r emoval procedure. DIMM baffle To remove the component: 1. Power down the server blade (on page 23 ). 2. Remove the server blade (on page 23 ). 3. Remove the access pa[...]

  • Seite 26

    4. Disconnect the hard drive cables. 5. Remove the hard d rive (" Hard drive " on page 24 ). 6. Remove the DIMM baffle. To replace the component, reverse the r emoval procedure. DIMMs To remove the component: 1. Power down the server blade (on page 23 ). 2. Remove the server blade (on page 23 ). 3. Remove the access panel (" Access p[...]

  • Seite 27

    For this procedure, removing the hard drive from the DI MM baffle is not required. 6. Remove the DIMM. To replace the component, reverse the r emoval procedure. Mezzanine card Optional mezzanine cards enable network connectivity and provide Fibre Channel support. For mezzanine card locations, s ee the system board components (on page 52 ). To remov[...]

  • Seite 28

    To replace the component: 1. Install the mezzanine card. Press down above the back side of the connector to seat the card. 2. Install the access panel (" Access panel " on page 24 ). 3. Install the server blade. Front bezel To remove the component: WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the [...]

  • Seite 29

    To replace the component, reverse the r emoval procedure. Server blade handle To remove the component: 1. Power down the server blade (on page 23 ). 2. Remove the server blade (on page 23 ). 3. Remove the access panel (" Access panel " on page 24 ). 4. Remove the front bezel (" Fr ont bezel " on page 28 ). 5. Remove the server b[...]

  • Seite 30

    6. Remove the release button. To replace the component, reverse the r emoval procedure. Heatsink WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. To remove the component: 1. Power down the server blade (on page 23 ). 2. Remove the server blade (on pag[...]

  • Seite 31

    To replace the component: 1. Clean the old thermal grease fr om the processor with the alcohol swab. Allow the alcohol to evaporate before continuing. CAUTION: The heatsink thermal interface media is not reusable and must be replaced if the heatsink is removed from the proces sor after it has been installed. 2. Apply all the grease to the top of th[...]

  • Seite 32

    4. Install the heatsink. Insert both screws, and then alternate tightening until the heatsink is seated properly. 5. Install the access panel (" Access panel " on page 24 ). 6. Install the server blade. Processor WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool b[...]

  • Seite 33

    5. Open the processor retaining latch and the processor socket retaining bracket. 6. Using your fingers, remove the failed processor. To replace the component: CAUTION: The pins on the processor s ocket are very fragile. Any damage to them may require replacing the system board. CAUTION: Failure to completely open t he processor locking lever preve[...]

  • Seite 34

    1. If the processor has separated from the installation tool, carefully re-insert th e proces sor in the tool. 2. Align the processor installation tool with the socket and install the processor. CAUTION: The processor is design ed to fit one way into the socket. Use the alignment guid es on the processor and socket to properly align the processor w[...]

  • Seite 35

    3. Press down firmly until the processor in stallation tool clicks and separates from the processor, and then remove the processor installation tool. 4. Close the processor retaining bracket and the processor retaining latch. 5. Clean the old thermal grease fr om the heatsink with the alcohol swab. Allow the alcohol to evaporate before continuing. [...]

  • Seite 36

    CAUTION: To avoid damage to the system board, processor soc ket, and screws, do not overtighten the heatsink screws. Use the wren ch supplied with the system to reduce the possibility of overtightenin g the screws. 7. Install the heatsink. Insert both screws, and then alternate tightening until the heatsink is seated properly. 8. Install the access[...]

  • Seite 37

    2. Remove the server blade (on page 23 ). 3. Remove the access panel (" Access panel " on page 24 ). 4. Remove the battery tray. To replace the component, reverse the r emoval procedure. System board To remove the component: 1. Power down the server blade (on page 23 ). 2. Remove the server blade (on page 23 ). 3. Remove the access panel [...]

  • Seite 38

    11. Open the processor retaining latch and the processor socket retaining bracket. 12. Using your fingers, remove the processor from the failed system board. CAUTION: To avoid damage to the system board: • Do not touch the processor socket contacts. • Always install the processor socket cover after removing the processor from the s ocket. • D[...]

  • Seite 39

    13. Remove the system board assembly. To replace the system board: 1. Install the spare system board assembly. 2. Prepare the processor socket on the spare syst em board: Removal and replacement procedures 39[...]

  • Seite 40

    a. Remove the processor socket protective cover. b. Open the processor retaining latch and the processor socket retaining bracket. 3. Install the processor socket cover onto the pr ocessor socket of the f ailed system board. 4. Install the processor on the spare system board. CAUTION: The processor is design ed to fit one way into the socket. Use t[...]

  • Seite 41

    5. Close the processor retaining latch and th e processor socket retaini ng bracket. 6. Clean the old thermal grease fr om the heatsink an d the top of the processor with the alcohol swab. Allow the alcohol to evapo rate before continuing. 7. Apply all the grease to the top of the processor in one of the foll owing patterns to ensure even distribut[...]

  • Seite 42

    8. Install the heatsink (" Heatsink " on page 30 ). 9. Install all components removed fr om the failed syst em board. IMPORTANT: Install all components with the same co nfiguration that was used on the failed system board. After you replace the system board, you must re-ent er the server serial number and the product ID. 1. During the ser[...]

  • Seite 43

    WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery. • Do not expose the battery to temperatures higher than 60°C (140?[...]

  • Seite 44

    C abling Hard drive cabling CAUTION: When routing cables, always be sure th at the cables are not in a position where they can be pinched or crimped. Using the HP c-Class Blade SUV Cable The HP c-Class Blade SUV Cable enables the user to perform server blade adminis tration, configuration, and diagnostic procedures by connecting video and U SB devi[...]

  • Seite 45

    Numerous configurations are possible. This sectio n offers tw o possible co nfigurations. For more information, see " USB support and functionality (on page 49 )." Accessing a server blade with local KVM For this configuration, a USB hub is not necessary. To connect addi tional devices, use a USB hub. CAUTION: Before disconnecting the SUV[...]

  • Seite 46

    1. Connect the SUV cable to the serv er blade. 2. Connect the video connector to a monitor. 3. Connect a USB hub to one USB connector. 4. Connect the following to the USB hub: o USB CD/DVD-ROM drive o USB keyboard o USB mouse o USB diskette Item Description 1 Monitor 2 USB mouse 3 HP c-Class Blade SUV Cable 4 Server blade 5 USB hub 6 USB keyboard 7[...]

  • Seite 47

    Diagno s tic tools Troubleshooting resources The HP ProLiant Servers Trouble shooting Guide provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, error message interpretation, issue resolution, and software maintenance on ProLiant servers and server bl ades. This guide includes[...]

  • Seite 48

    This functionality supports o perating systems that may not be supported by the server blade. For operating systems supported by the server blade, see the HP website ( http://www.hp.com/go/supporto s ). If a significant change occurs betw een data-gathering intervals, the su rvey functi on marks the previous information and overwrites the survey da[...]

  • Seite 49

    Redundant ROM support The server enables you to up grade or configure the ROM safely with redundant ROM support. The server has a 4-MB ROM that acts as two, separate 2-MB RO Ms. In the standard implementation, one side of the ROM contains the current ROM program versi on, wh ile the other side of the ROM contains a backup version. NOTE: The server [...]

  • Seite 50

    C ompone nt i dentif icati on Front panel components Item Description 1 Local I/O conn ector 2 Serial label pull tab 3 Server blade handle button 4 Power On/Standby button 5 Server blade handle Component identification 50[...]

  • Seite 51

    Front panel LEDs Item Description Status 1 UID LED Blue = Identified Blue flashing = Active remote management Off = No active remote management 2 Internal health LED Green = Normal Flashing = Booting Amber = Degraded condition Red = Critical condition 3 NIC 1 LED Green = Network linked Green flashing = Network activity Off = No link or activity 4 N[...]

  • Seite 52

    System board components Item Description 1 DIMM slots 2 Hard drive data connect or 2 3 Hard drive data connector 1 4 Hard drive power connector 1 5 Hard drive power connector 2 6 Internal USB connector 7 System battery 8 Enclosure connector 9 Battery tray 10 Mezzanine connector 1 (Type I only) 11 Mezzanine connector 2 (Type I or Type II) 12 System [...]

  • Seite 53

    System maintenance switch Position Function Default 1* iLO 2 security override Off 2 Configuration lock Off 3 Reserved Off 4 Reserved Off 5* Password disabled Off 6* Reset configuration Off 7 Reserved Off 8 Reserved Off *To access redundant ROM, set S1, S5, and S6 to ON. System maintenance switch procedures When you perform troubleshooting steps, t[...]

  • Seite 54

    Accessing the redundant ROM If the system ROM is corrupt ed, the system automatica lly switches to the redundant ROM in most cases. If the system does not automatically switch to th e redundant ROM, perform the foll owing steps: 1. Power down the server blade (on page 23 ). 2. Remove the server blade (on page 23 ). 3. Remove the access panel ("[...]

  • Seite 55

    Sp e c i fic a t io n s Environmental specifications Specification Value Temperature range* Operating 10 ° C to 35 ° C (50 ° F to 95 ° F) Shipping -40 ° C to 60 ° C (-40 ° F to 140 ° F) Storage -20°C to 60°C (-4°F to 140°F) Maximum wet bulb temperature 30 ° C (86 ° F) Relative humidity (noncondensing)** Operating 10% to 90% Shipping 1[...]

  • Seite 56

    A c r on y ms and a bbr e v i ati ons CSR Customer Self Repair HP SIM HP Systems Insight Manager iLO 2 Integrated Lights-Out 2 IML Integrated Management Log ISEE Instant Support Enterprise Edition OSEM Open Services Event Manager POST Power-On Self Test PSP ProLiant Support Pack RBSU ROM-Based Setup Utility SUV serial, USB, video UID unit identific[...]

  • Seite 57

    WEBES Web-Based Enterprise Service Acronyms and abbreviations 57[...]

  • Seite 58

    Inde x A  access panel 24 Array Diagnostic Utility (ADU) 48 B  baffles 25 battery 16, 42 buttons 50 C  cables 44 cabling 44 cautions 21 component identification 50, 52 components 50, 52 connectors 50, 52 CSR (customer self repair) 5 customer self repair (CS R) 5 D  diagnostic tools 47 diagnostics utility 47 DIMM baffles 25 DIMMs 26, 52 [...]

  • Seite 59

    system battery 42 system board 37 system components 21, 50 system maintenance switch 52, 53 T  tools 21, 47 Torx screwdriver 21 troubleshooting 47 U  USB connectors 52, 54 USB support 49 utilities 47 V  video connector 54 W  warnings 21 Index 59[...]