Husqvarna 325R Bedienungsanleitung

Oper a tor's manual (EP A II) Please read these instructions car efully and make sure y ou understand them befor e using the machine . English 323R 325R X-SERIES 325R XT -SERIES 325RD X-SERIES[...]

2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine. U se anti-slip and stable boots. Always wear [...]

English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal protective equipment ............................................. 4 The [...]

4 – English The machine‘s safety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “What is what“ to locate where this equipment is positioned on your machine.) Personal protective equipment SAFETY INSTR UC[...]

English – 5 2. Stop switch The stop switch should be used to stop the engine. 3. Cutting attachment guard This guard is intended to prevent objects from being thrown to wards the operator and to protect the operator from unintentionel contact with the cutting attachment. 4. Anti-vibration system Y our machine is equipped with an anti-vibration sy[...]

6 – English SAFETY INSTR UCTIONS 6. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine ‘ s exhaust fumes away from the operator . Muffler fitted with catalytic converter is also designed to reduce harmful exhaust components. In countries that have a warm and dry climate the risk of fire is obvious. [...]

English – 7 SAFETY INSTR UCTIONS 1. Throttle trigger lock • Check that the throttle is locked in the “ idling position “ when the throttle trigger lock is in its original position. • Press in the throttle trigger lock and make sure it returns to its original position when released. • Ensure that the throttle and throttle trigger lock mo[...]

8 – English SAFETY INSTR UCTIONS 3. Cutting attachment guard • Check that the guard is undamaged and not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" . 5. Muffler 1. Never use a machine that has a defective muffler.[...]

English – 9 7. Quick-release • Check that the harness straps are correctly positioned. When the harness and machine are adjusted, check the harness ‘ safety release catch to ensure it works correctly. SAFETY INSTR UCTIONS 6. Cutting equipment This section describes how through corr ect maintenance and through using the right type of cutting e[...]

10 – English SAFETY INSTR UCTIONS Cutting equipment Sharpening the grass blade • See the cutting equipment ’ s packaging for correct filing instructions. • The blades are sharpened using a single cut flat file. • Sharpen all edges equally to maintain the balance of the blade. Trimmer head • Only use a trimmer head and trimmer cord that [...]

English – 11 SAFETY INSTR UCTIONS General safety instructions IMPORT ANT INFORMA TION • This machine is intended solely for trimming and clearing grass and for light brush-cutting. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “ T echnical data “ . • Never use [...]

12 – English General working instructions SAFETY INSTR UCTIONS Basic safety precautions 1. Observe your surroundings: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that the above mentioned do not come into contact with the cutting equipment or objects that can be thrown by the cutting [...]

English – 13 SAFETY INSTR UCTIONS Adjusting the harness and clearing saw Designations • Use a saw blade for cutting woody growth with thin stems. • Use a grass knife or grass blade for clearing grass. • Use a trimmer head or plastic blades for lighter clearing work, for example along verges or around trees. Basic clearing techniques • Alw[...]

14 – English SAFETY INSTR UCTIONS Clearing ‘ s ABC A. Always use the correct equipment. B. Always have well adjusted equipment. C. Follow the safety instructions. D. Organise the work well. E. Always use full throttle when applying the blade. F. Always use a sharp blade. G. Avoid stones. ! W ARNING! A void cutting in the cutting region between [...]

English – 15 SAFETY INSTR UCTIONS Grass clearing using the trimmer head and plastic blades. • Hold the trimmer head just above the ground at an angle. It is the end of the cord that carries out the work. Let the cord work at its own pace. Do not press the cord into the area to be cut. • The cord can easily remove grass and weeds up against wa[...]

16 – English WHA T IS WHA T? What is what on the brushcutter? 1. Blade 2. Gr ease filler cap 3. Angle gear 4. Combination guard 5. Shaft 6. Handlebars 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Hanging ring 11. C ylinder cover 12. S tar ter handle 13. F uel tank 14. Choke 15. Air purge 16. Air filter co ver 17. Clutch co ver 18. Hand[...]

English – 17 Assembling the handlebars (323R) ASSEMBL Y Assembling the handlebar s (325R X , 325R XT , 325RD X ) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the [...]

18 – English ASSEMBL Y Assembly of the blade and trimmer head Assembling the blade guard and clearing blade • Remove the mounting plate (H). Fit the adapter (I) and bracket (J) with the two screws (K) as shown. Fit the blade guard (A) to the adapter using the 4 screws (L) as shown. NOTE! Use the recommended blade guard. “ See Technical data ?[...]

English – 19 ASSEMBL Y Assembling the spray guard and trimmer head Superauto II • Fit the appropriate guard (A) for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). • Fit the disc drive (B) on the output axle. • Turn the blade axle until one of the disc drive ’ s holes aligns with the corre[...]

20 – English ASSEMBL Y Adjusting the harness and clearing saw Quick release On the front is an easily accessible, quick release catch. U se this if the engine should catch fire or in any other emergency situation when you quickly need to take off the harness and machine. Even load on the shoulders A well-adjusted harness and clearing saw signific[...]

English – 21 FUEL HANDLING Fuel mixture • Clean around the fuel cap. Contamination in the tank can disrupt operations. • Ensure that the fuel is well mixed by shaking the container before filling the tank. W ARNING! Always provide good ventilation when handling fuel. ! Fuelling W ARNING! The following precautions reduce the risk of fire: Do n[...]

22 – English ST AR T AND ST OP Control before starting Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P r ess the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Warm engine U se the same starting [...]

English – 23 ST AR T AND ST OP W ARNING! When the engine is started with the choke in the choke or start position the cutting equipment starts to rotate immediately . ! Start Pr ess the machine body against the ground using your left hand (NO TE! Not your foot). G rip the starter handle, slowly pull out the cord with your right hand until you fee[...]

24 – English Carburetor Y our H usqvarna pr oduct has been designed and manufactured to specifications that r educe harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. T o ensure that your unit is at peak performance and producing the least amount of harmful emissions after br eak in, have your authorized [...]

English – 25 Final setting of the idling speed T Adjust the idling speed with the screw T , If it is necessary to readjust. F irst turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ mo ve. Then turn, counter- clockwise until the cutting attachment stops. A correctly adjusted idle speed setting occurs wh[...]

26 – English MAINTENANCE Cooling system T o maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4. Cylinder cover (leads cold air onto the cylinder). Clean the cooling[...]

English – 27 Spark plug The condition of the spark plug is affected by: • An incorrect carburetor setting. • An incorrect fuel mixture (too much or faulty oil). • A dirty air filter. These factors cause deposits on the spark plug electrode that may result in malfunction or starting difficulties. If the machine is low on po wer , difficult t[...]

28 – English MAINTENANCE NOTE : Use only HUSQ V ARNA replacement parts. U se of other brands of replacement parts can cause damage to your unit or injur y to the operator or others. Y our warranty does not cover damage or liability caused b y the use of accessories and/or attachments not specifically recommended by HUSQV ARNA. Maintenance schedul[...]

English – 29 TECHNICAL D A T A T echnical data Engine Displacement, cu. in/cm 3 Cylinder bor e, inch/mm Stroke length, inch/mm Idling speed, rpm Recommended max. speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893. kW/rpm Catalytic converter muffler Speed-r egulated ignition system Ignition system Manufactur er/type of igni[...]

30 – English TECHNICAL D A T A Approved accessories 323R Centre hole in blades Ø 25,4 mm Threaded blade axle M10 G rass blade Saw blade Plastic knives T rimmer head Support cup T ype Grass 255-4 1" ( ∅ 255 4-teeth) Grass 255-8 1" ( ∅ 250 8-teeth) Maxi X 200-26 1" (∅ 200 26-teeth) T ricut ∅ 300 T rimmy F ix T rimmy H II 1&q[...]

English – 31 EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. In U.S. and Canada, new small nonroad engines [...]

32 – English 1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm[...]

English – 33 1 T ri Cut 2 3 4 5 6 7 8 >20mm >20mm ! B A 6 Nm X 10[...]

34 – English 1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6"[...]

English – 35 1 T rimmy Hit 23 4 5 6 7 8 9 10 11 “ Click ” “ Click ” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6[...]

36 – English 1 T rimmy Hit Junior 2 5 6 7 8 9 10 12 “ Click ” 3 4 5,75 m 19' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 2,8 m 9' 1.) 2.) 11 15 cm 6" 15 cm 6"[...]

English – 37 1 T rimmy Hit Pro 2 5 6 7 8 9 10 12 “ Click ” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6"[...]

38 – English 1 T rimmy Hit VI 2 5 6 3 4 7 8 9 10 11 “ Click ” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6[...]

English – 39 1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII[...]

40 – English[...]

English – 41[...]

42 – English ´+H*G¶5q¨[...]

English – 43[...]

2002W13 ´+H*G¶5q¨ 114 01 03 -95[...]