Husqvarna 327RJx Bedienungsanleitung

E E E E n n n n g g g g l l l l i i i i s s s s h h h h 327RJ X-series Oper ator’ s manual (EP A) Please r ead the operator’ s manual carefully and mak e sure you understand the instructions before using the machine.[...]

KEY T O SYMBOLS 2 – English Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’ s manual. Please read the operator’ s manual carefully and make[...]

CONTENTS English – 3 Contents Note the f ollowing bef ore starting: Please read the oper ator’ s manual carefully . Maintenance, replacement, or repair of the emission control devices and system ma y be performed by any nonroad engine repair establishment or individual. This engine label cer tifies that the product is cer tified in accordance[...]

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to b uy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River , for production of muskets . The location was logical, since w ater power was harn[...]

English – 5 WHA T IS WHA T? What is what on the trimmer? 1 3 2 4 17 18 24 25 19 4 26 21 27 16 7 28 8 9 30 10 29 11 12 15 14 13 22 23 20 1 5 6 1 T r immer head 2 Grease filler cap, be vel gear 3 Bev el gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock out 10 Cylinder cov er 11 Star ter handle 1[...]

GENERAL SAFETY PRECA UTIONS 6 – English Impor tant P ersonal protective equipment HELMET A protectiv e helmet where there is a risk of falling objects HEARING PRO TECTION Wear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approved e ye protection. If you use a visor then you must also w ear approved prote[...]

GENERAL SAFETY PRECA UTIONS English – 7 BOO TS Wear boots with steel toe-caps and non-slip sole . CLO THING Wear clothes made of a strong f abric and avoid loose clothing that can catch on twigs and branches. Alwa ys wear heavy , long pants. Do not wear jewellery , shorts sandals or go barefoot. Secure hair so it is abo ve shoulder lev el. FIRST [...]

GENERAL SAFETY PRECA UTIONS 8 – English Stop s witch Use the stop switch to s witch off the engine. Star t the engine and make sure the engine stops when you mov e the stop switch to the stop setting. Cutting attachment guar d This guard is intended to prev ent loose objects from being thrown tow ards the operator . The guard also protects the op[...]

GENERAL SAFETY PRECA UTIONS English – 9 fi tted with a catalytic conv er ter is also designed to reduce harmful exhaust gases. In countries that have a w ar m and dry climate there is a significant risk of fire. W e therefore fit certain mufflers with a spark arrestor screen. Check whether the muffler on your machine is fitted with this ki[...]

GENERAL SAFETY PRECA UTIONS 10 – English Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Reduce the risk of blade thrust. • Obtain maximum cutting perf or mance. • Extend the life of cutting equipment. Cutting equipment Grass blades and g rass cutters are intended for cutting coarse [...]

GENERAL SAFETY PRECA UTIONS English – 11 T rimmer head • Only use the recommended trimmer heads and trimmer cords. These have been tested b y the manuf acturer to suit a par ticular engine size. This is especially impor tant when a fully automatic trimmer head is used. Only use the recommended cutting attachment. See the chapter on T echnical d[...]

ASSEMBL Y 12 – English Fitting the J-handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw . Do not overtighten. • Attach the J-handle to the loop handle using the three screws, as sho wn. ?[...]

ASSEMBL Y English – 13 CA UTION! Use the recommended blade guard. See the T echnical data section. • Fit the drive disc (B) on the output shaft. • T ur n the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Inser t the locking pin (C) in the hole to loc k the shaft. • Place the[...]

FUEL HANDLING 14 – English Fuel safety Nev er star t the machine: 1 If you ha ve spilled fuel on it. Wipe off the spillage and allow remaining fuel to e vaporate. 2 If you ha ve spilled fuel on yourself or y our clothes, change your clothes. W ash any part of your body that has come in contact with fuel. Use soap and water . 3 If the machine is l[...]

FUEL HANDLING English – 15 Mixing • Alwa ys mix the gasoline and oil in a clean container intended for fuel. • Alwa ys star t by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the fuel mixture thoroughly bef ore fillin[...]

ST AR TING AND ST OPPING 16 – English Check bef ore star ting • Check the b lade to ensure that no cracks hav e formed at the bottom of the teeth or by the centre hole. The most common reason why cr acks are formed is that sharp cor ners have been f ormed at the bottom of the teeth while sharpening or that the blade has been used with dull teet[...]

ST AR TING AND ST OPPING English – 17 Choke: Set the choke control in the chok e position. Hold the body of the machine on the ground using your left hand (CA UTION! Not with your foot!). Grip the star ter handle, slowly pull out the cord with y our right hand until you f eel some resistance (the star ter pawls grip), now quickly and pow erfully [...]

W ORKING TECHNIQUES 18 – English General working instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot affect y our control of the machine. • T o ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting atta[...]

W ORKING TECHNIQUES English – 19 Basic working tec hniques Alwa ys slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. Grass clearing using a grass b lade • Grass blades and g rass cutters must not be used on woody stems. • A grass b lade i[...]

W ORKING TECHNIQUES 20 – English Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower . Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool. • Do not allow the trimmer head to constantly come into c[...]

MAINTENANCE English – 21 Carburetor Y our Husqvarna product has been designed and manuf actured to specifications that reduce har mful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. T o ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running-in period, as[...]

MAINTENANCE 22 – English Low speed jet L T r y to find the highest idling speed, tur ning the low speed needle L clockwise respectiv ely counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/4 turn counter-clockwise. CA UTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw [...]

MAINTENANCE English – 23 Muffler CA UTION! Some mufflers are fitted with a catalytic conv er ter. See chapter on T echnical data to see whether your machine is fitted with a catalytic con ver ter . The muffler is designed to reduce the noise le vel and to direct the exhaust gases a way from the oper ator. The exhaust gases are hot and can co[...]

MAINTENANCE 24 – English before taking an y fur ther action. If the spar k plug is dir ty , clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spar k plug should be replaced after about a month in operation or earlier if necessary . CA UTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the[...]

English – 25 MAINTENANCE Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and ser vice work described in this manual. More extensive w or k must be carried out by an authorised ser vice wo[...]

26 – English TECHNICAL D A T A T echnical data NO TE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’ s approved cutting equipment fitted. The table indicates the highest and lowest v alues. Note 1: Equivalent noise pressure le vel is calculated as the time-weighted energy total for noise pres[...]

FEDERAL AND CALIFORNIA EMISSIONS CONTR OL W ARRANTY ST A TEMENT English – 27 Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and Jonsered are pleased to explain the emissions control system’ s warranty on your 2007 and later small off-road engine.[...]

FEDERAL AND CALIFORNIA EMISSIONS CONTR OL W ARRANTY ST A TEMENT 28 – English EMISSION W ARRANTY P ARTS LIST 1 Carburetor and internal par ts 2 Intake pipe, airfilter holder and carb uretor bolts. 3 Airfilter and fuelfilter cov ered up to maintenance schedule. 4 Spark Plug, covered up to maintenance schedule 5 Ignition Module 6 Muffler with ca[...]

[...]

"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35[...]

1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5[...]

T35, T35x "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm[...]

"Clic" 1 2 3 5 6 7 9 6,0 m 18' 4 8 3,05 m 9' 2,0-2,4 mm .079-.095" 10 cm 4" 6" 15 cm T25[...]

[...]

[...]

1150990-95 ´®z+R•)¶5p¨ ´®z+R•)¶5p¨ 2009-04-10[...]