Husqvarna 335FR Bedienungsanleitung

E E E E n n n n g g g g l l l l i i i i s s s s h h h h 333R 335FR 335R X-series Oper ator’ s manual (EP A) Please r ead the operator’ s manual carefully and mak e sure you understand the instructions before using the machine.[...]

KEY T O SYMBOLS 2 – English Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine. Alwa ys wear : • A protective [...]

CONTENTS English – 3 Contents Note the f ollowing bef ore starting: Please read the oper ator’ s manual carefully . Maintenance, replacement, or repair of the emission control devices and system ma y be performed by any nonroad engine repair establishment or individual. This label cer tifies that the product has been certified in accordance w[...]

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to b uy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River , for production of muskets . The location was logical, since w ater power was harn[...]

English – 5 WHA T IS WHA T? What is what on the c learing saw? 4 21 22 20 12 21 25 1 19 6 13 4 15 28 24 26 23 27 32 17 10 33 14 29 16 5 31 18 11 2 3 9 30 8 7 1 4 17 33 333R 335FR 1 T r immer head 2 Grease filler cap, be vel gear 3 Bev el gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop switch 9 Throttle lock out 10 S[...]

GENERAL SAFETY PRECA UTIONS 6 – English Impor tant P ersonal protective equipment HELMET A helmet should be w orn if the trees being cleared are taller than 2 m. HEARING PRO TECTION Wear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approved e ye protection. If you use a visor then you must also w ear app[...]

GENERAL SAFETY PRECA UTIONS English – 7 BOO TS Wear boots with steel toe-caps and non-slip sole . CLO THING Wear clothes made of a strong f abric and avoid loose clothing that can catch on twigs and branches. Always wear heavy , long pants. Do not wear jewellery , shor ts sandals or go barefoot. Secure hair so it is above shoulder lev el. FIRST A[...]

GENERAL SAFETY PRECA UTIONS 8 – English Stop s witch Use the stop s witch to switch off the engine . Star t the engine and mak e sure the engine stops when you mov e the stop switch to the stop setting. Cutting attac hment guard This guard is intended to prev ent loose objects from being thrown tow ards the operator . The guard also protects the [...]

GENERAL SAFETY PRECA UTIONS English – 9 Cer tain harnesses also hav e a quick release fitted to the suppor t hook. Check that the harness straps are correctly positioned. Once the harness and machine have been adjusted, check that the harness quick release works correctly . Muffler The muffler is designed to keep noise le vels to a minimum and[...]

GENERAL SAFETY PRECA UTIONS 10 – English Locking n ut A locking nut is used to secure some types of cutting attachment. When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. T o remove it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left-h[...]

GENERAL SAFETY PRECA UTIONS English – 11 K eep the correct setting on the saw blade! F ollow our instructions and use the recommended setting tool. An incorrectly set saw b lade increases the r isk of jamming and blade thrust, and damage to the saw b lade. Check the cutting attachment f or damage or cracks. A damaged cutting attachment should alw[...]

GENERAL SAFETY PRECA UTIONS 12 – English T rimmer head • Only use the recommended trimmer heads and trimmer cords. These have been tested b y the manuf acturer to suit a par ticular engine size. This is especially impor tant when a fully automatic trimmer head is used. Only use the recommended cutting attachment. See the chapter on T echnical d[...]

ASSEMBL Y English – 13 Assembling the handlebar and throttle • Remov e the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the handlebar , (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar . • Refit the screw in the hole in the rear of the throttle han[...]

ASSEMBL Y 14 – English The guard extension is remo ved easily using the spark plug spanner , see illustration. Fitting a blade guar d, grass b lade and grass cutter • Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt. CA UTION! Ensure that the guard extension is remov ed. Use the recommended blad[...]

ASSEMBL Y English – 15 • Inser t the loc king pin (C) in the hole to lock the shaft. • Place the blade (D) and support flange (F) on the output shaft. • Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possib [...]

ASSEMBL Y 16 – English Adjusting the harness and clearing sa w Standard harness Quick release At the front is an easily accessible, quic k release. Use this if the engine catches fire or in any other emergency situation that requires you to free y ourself from the machine and harness. Spreading the load on y our shoulders A well-adjusted harness[...]

ASSEMBL Y English – 17 2 Tighten the chest strap under your left arm so that it fits closely around your body . 3 Adjust the shoulder strap to distribute the load e venly across your shoulders. Press downwards on the suspension hook to load the harness. 4 Adjust the height of the suspension hook as described in the instructions for the standard [...]

FUEL HANDLING 18 – English Fuel safety Nev er star t the machine: 1 If you ha ve spilled fuel on it. Wipe off the spillage and allow remaining fuel to e vaporate. 2 If you ha ve spilled fuel on yourself or y our clothes, change your clothes. W ash any par t of your body that has come in contact with fuel. Use soap and water . 3 If the machine is [...]

FUEL HANDLING English – 19 Mixing • Alwa ys mix the gasoline and oil in a clean container intended for fuel. • Alwa ys star t by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the fuel mixture thoroughly bef ore fillin[...]

ST AR TING AND ST OPPING 20 – English Check bef ore star ting • Check the b lade to ensure that no cracks hav e formed at the bottom of the teeth or by the centre hole. The most common reason why cr acks are formed is that sharp cor ners have been f or med at the bottom of the teeth while sharpening or that the blade has been used with dull tee[...]

ST AR TING AND ST OPPING English – 21 Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb . The b ulb need not be completely filled. Hold the body of the machine on the ground using your left hand (CA UTION! Not with your foot!). Grip the star ter handle, slowly pull out the cord with y our right hand until you f eel [...]

W ORKING TECHNIQUES 22 – English General working instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot affect y our control of the machine. • T o ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting atta[...]

W ORKING TECHNIQUES English – 23 W orking methods • Before y ou star t clear ing, check the clearing area, the type of terrain, the slope of the ground, whether there are stones, hollows etc. • Star t at whichev er end of the area is easiest, and clear an open space from which to work. • Work systematically to and fro across the area, clear[...]

W ORKING TECHNIQUES 24 – English the same time push the stem using the blade guard. Cut with the area of the blade between 3 o’cloc k and 5 o’clock. Apply full throttle before advancing the blade. • T o fell to the right, the bottom of the tree should be pushed to the left. Tilt the blade and bring it diagonally up to the right. Cut with th[...]

W ORKING TECHNIQUES English – 25 Grass clearing using a grass b lade • Grass blades and g rass cutters must not be used on woody stems. • A grass b lade is used for all types of tall or coarse grass. • The grass is cut down with a side ways , swinging mov ement, where the movement from right-to-left is the clearing stroke and the mov ement [...]

MAINTENANCE 26 – English Carburetor Y our Husqvarna product has been designed and manuf actured to specifications that reduce har mful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. T o ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running-in period, as[...]

MAINTENANCE English – 27 Low speed jet L T r y to find the highest idling speed, tur ning the low speed needle L clockwise respectiv ely counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/4 turn counter-clockwise. CA UTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw [...]

MAINTENANCE 28 – English Adjusting the start throttle speed The correct star t throttle speed is set by means of an adjuster on the rear of the handle next to the cab le. Use this screw (4 mm Allen scre w) to increase or decrease the star t throttle speed. Proceed as follo ws: 1 Run the machine at idle. 2 Press the star t throttle lock as describ[...]

MAINTENANCE English – 29 Cooling system T o keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Cooling fins on the cylinder . 3 Cylinder cov er (directs cold air over the cylinder). Clean the cooling system with a brush once a week, more of[...]

MAINTENANCE 30 – English Spark plug The spark plug condition is influenced by: • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dir ty air filter . These factors cause deposits on the spark plug electrodes, which ma y result in operating problems and star ting difficulties. If the ma[...]

English – 31 MAINTENANCE Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carr y out the maintenance and ser vice work described in this manual. More extensiv e work must be carried out by an authorised ser vice wo[...]

32 – English TECHNICAL D A T A T echnical data Note 1: Equivalent noise pressure le vel is calculated as the time-weighted energy total for noise pressure le vels under various working conditions with the follo wing time distribution: 1/2 idle and 1/2 max. speed. NO TE! Noise pressure at the user’s ear and vibration on the handles are measured [...]

English – 33 TECHNICAL D A T A Appro ved accessories T ype Cutting attachment guard, Ar t. no. Centre hole in blades/cutters, Ø 25,4 mm Output shaft thread M12 Grass blade/g rass cutter Multi 255-3 (Ø 255 3 teeth) 537 33 16-01 Grass 255-4 (Ø 255 4 teeth) 537 33 16-01 Multi 275-4 (Ø 275 4 teeth) 537 33 16-01 Multi 300-3 (Ø 300 3 teeth) 537 33[...]

FEDERAL AND CALIFORNIA EMISSIONS CONTR OL W ARRANTY ST A TEMENT 34 – English Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and Husqvarna Forest & Garden are pleased to e xplain the emissions control system’ s warranty on your 2007 and later [...]

FEDERAL AND CALIFORNIA EMISSIONS CONTR OL W ARRANTY ST A TEMENT English – 35 EMISSION W ARRANTY P ARTS LIST 1 Carburetor and internal par ts 2 Intake pipe, airfilter holder and carb uretor bolts. 3 Airfilter and fuelfilter cov ered up to maintenance schedule. 4 Spark Plug, covered up to maintenance schedule 5 Ignition Module 6 Muffler with ca[...]

[...]

"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35[...]

1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5[...]

T35, T35x "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm[...]

"Clic" 1 2 3 5 6 7 9 10 m 32' 4 8 4,3 m 14' 2,7-3,3 mm .106-.13" 10 cm 4" 6" 15 cm T45, T45x[...]

2,7-3,3 mm .106-.130" 15 cm 6" 15 cm 6" 15 cm 6" 15 cm 6" 1 2 3 5 6 7 10 11 1.) 2.) >1,1 Kw <1,1 Kw 2,7 mm - 9,0 m 3,0 mm - 7,5 m 3,3 mm - 6,0 m 4 8 Auto 55[...]

1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII[...]

[...]

1151115-95 ´®z+S+[¶5O¨ ´®z+S+[¶5O¨ 2008-03-05[...]