JVC HR-DD857MS Bedienungsanleitung

H R-DD857MS VIDEO CASSETTE RECORDER INSTRUCTIONS LPT0110-001C PAL NTSC T V P R O G + T V V O L – T V P R O G – T V V O L + VCR CANCEL TIMER START STOP DATE PUSH JOG MENU OK TV PROG TV/VCR (MONITOR) C. RESET DAILY AUX WEEKLY PROG. CHECK PROG. DISPLAY AUDIO 123 456 7 89 0 2 4 1 3 EXPRESS PROGRAMMING MULTI BRAND REMOTE CONTROL UNIT TV 30 SEC REW I[...]

2 EN SAFETY FIRST IMPORT ANT n Please read the various precautions on this page before installing or operating the recorder . n It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video record- ing, broadcast or cable programme and in any literar[...]

EN 3 Basic Connections CHECK CONTENTS 1 Make sure the package contains all of the accessories listed in “Specifications” ( Z pg. 53). SITUA TE RECORDER 2 Place the recorder on a stable, horizontal surface. CONNECT RECORDER TO TV 3 The connection method you use depends on the type of TV you have. RF CONNECTION ● T o Connect T o A TV With NO A [...]

4 EN V ideo Channel Set INITIAL SETTINGS V ideo Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below . If you have c[...]

EN 5 (Ex.) If channel 50 is available in your area SET VIDEO CHANNEL 3 Set your TV to UHF channel 36. ● If the two vertical white bars appear clearly on the screen as shown in the illustration ( Z "TEST SIGNAL" on page 4), press OK and then go to step 4 . ● If the two vertical white bars do not appear clearly , press OK and then TV PR[...]

6 EN 123 456 7 89 0 2 4 1 3 INITIAL SETTINGS (cont.) Auto Set Up Before starting, make sure of the following: ● The TV aerial cable should be connected to the recorder . ● The recorder's mains power cord should be connected to a mains outlet. Z pg. 3 ● The "Video Channel Set" procedure should be done first and the TV should be [...]

EN 7 0 4 1 3 AUTO CH SET PLEASE WAIT STAR T FINISH TV Screen When Auto Set Up is completed, the lowest position number will appear on the front display panel. During Auto Set Up "PLEASE W AIT" blinks on the screen and "Auto" blinks on the front display panel. NOTES: ● If you perform Auto Set Up when the aerial cable is not con[...]

8 EN q6 PR. 12 ] SP 21 : 00 MESECAM 24. 12. 98 SPA TIALIZER ST SIM. ON HIFI L R –1 : 23 : 45 0 ++ + + INITIAL SETTINGS (cont.) On-Screen Displays Y ou can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF . T urn on the TV and select the VIDEO channel (or AV mode). TURN ON THE RECORD[...]

EN 9 Select Language T urn on the TV and select the VIDEO channel (or AV mode). MAIN MENU FUNCTION SET TUNER SET INITIAL SET [ 5 / ∞ ] = [MENU] : EXIT TURN ON THE RECORDER 1 Press . ACCESS MAIN MENU SCREEN 2 Press MENU . ACCESS INITIAL SET SCREEN 3 Press PUSH JOG %fi to place the pointer next to "INITIAL SET", then press OK or PUSH JOG[...]

10 EN Clock Set T urn on the TV and select the VIDEO channel (or AV mode). TURN THE RECORDER ON 1 Press . ACCESS MAIN MENU SCREEN 2 Press MENU . ACCESS INITIAL SET SCREEN 3 Press PUSH JOG %fi to place the pointer next to "INITIAL SET", then press OK or PUSH JOG . ACCESS CLOCK SET SCREEN 4 Press PUSH JOG %fi to place the pointer next to [...]

EN 11 123 456 7 89 0 2 4 1 3 PLA YBACK Basic Playback The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme. LOAD A CASSETTE 1 Make sure the window side is up, the rear label side is facing you a[...]

12 EN PLA YBACK (cont.) Playback Features High-Speed Search ACTIV A TE HIGH-SPEED SEARCH 1 During playback or still picture, press FF for forward high-speed sear ch, or REW for reverse high-speed sear ch. T o resume normal playback, press PLA Y . NOTE: For short searches, press and hold FF or REW for over 2 seconds during playback or still picture.[...]

EN 13 123 456 7 89 0 2 4 1 3 Manual T racking Y our video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the TV PROG buttons. OVERRIDE AUTOMA TIC TRACKING 1 Press (SP/LP/EP) on the remote to engage manual tracking. ADJUST TRACKING MANUALL Y 2 Press TV PROG + [...]

14 EN PLA YBACK (cont.) Index Search Y our recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. NOTE: Before starting, make sure the recorder is in the Stop mode. ACTIV A TE INDEX SEARCH 1 Press PUSH JOG or on the remote control. “ ™ 1?[...]

EN 15 Next Function Memor y Y ou can set your recorder's power to go off automatically after the tape is fully rewound. Before starting, make sure the recorder is in the Stop mode. For Automatic Power Off After T ape Rewind . . . . . . press REW , then press within 2 seconds. T ape Position Indicator The tape position indicator appears on scre[...]

16 EN 123 456 7 89 0 2 4 1 3 PLA YBACK (cont.) TimeScan Y our recorder is equipped with the TimeScan function. T imeScan allows noise free pictures to be displayed on your TV screen in the forward and reverse search modes. Audio will be played back at normal speed during the T imeScan modes ( Z pg. 17 ). T imeScan allows you to view a programm e in[...]

EN 17 Reverse Forward Search Play Slow-Motion *Still Slow-Motion Play Search SP -9x -7x -5x -3x -1x -1/6x -1/18x 0 1/18x 1/6x 1x 2x 3x 5x 7x 9x LP -7x -3x -1/6x -1/18x 0 1/18x 1/6x 1x 2x 5x 9x NTSC SP/EP -7x -5x -3x -1x -1/6x -1/18x 0 1/18x 1/6x 1x 2x 3x 5x 7x Audio output Audio is output. Audio is not Audio is Audio is not Audio is output. output.[...]

18 EN 123 456 7 89 0 2 4 1 3 TV signals being received by the recorder ’ s built-in tuner can be recorded onto a video tape. Y ou can “capture” a TV programme using your video recorder . RECORDING Basic Recording LOAD A CASSETTE 1 Insert a cassette with the record safety tab intact. ● The counter is reset to 0:00:00 and the recorder power c[...]

EN 19 123 456 7 89 0 2 4 1 3 Recording Features Record One Pr ogramme While W atching Another SELECT CHANNEL TO W A TCH 1 Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you wish to view . ● The programme selected with the TV’ s channel controls appears on the TV screen while the one se[...]

20 EN Receiving Stereo And Bilingual Pr ogrammes Y our recorder is equipped with a Sound-Multiplex decoder (A2) and a Digital stereo sound decoder (NICAM) as well, making reception of stereo and bilingual broadcasts possible. When the channel is changed, the type of broadcast being received will be displayed on the TV screen for a few seconds. T o [...]

EN 21 123 456 7 89 0 2 4 1 3 Simulcast Recording If FM simulcast TV programmes are available, you can record the TV programme with the soundtrack from an FM-broadcast. I n t he simulcast mode, the external audio programme is recorded on the audio track (both Hi-Fi and normal). MAKE CONNECTIONS 1 Connect the FM tuner to the rear panel AUDIO IN conne[...]

22 EN 123 456 7 89 0 2 4 1 3 B.E.S.T . Pictur e System T urn on the TV and select the VIDEO channel (or AV mode). The B.E.S.T . (Biconditional Equalised Signal T racking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting [...]

EN 23 Recording ST AR T RECORDING 1 Press and hold RECORD and press PLAY on the remote, or press RECORD on the recorder . DURING B.E.S.T . B.E.S.T . COMPLETE ● The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording. NOTES: ● The B.E.S.T . system works for both SP and LP (or EP) modes only after a [...]

24 EN TIMER RECORDING G- CODE Setup T urn on the TV and select the VIDEO channel (or A V mode). Guide Program Number Set ACCESS MAIN MENU SCREEN 1 Press MENU . ACCESS INITIAL SET SCREEN 2 Press PUSH JOG %fi to place the pointer next to "INITIAL SET", then press OK or PUSH JOG . ACCESS G-CODE SET -UP 3 Press PUSH JOG %fi to place the poi[...]

EN 25 ENTER RECEIVING CHANNEL POSITION NUMBER 5 Press PUSH JOG %fi or NUMBER keys to input the number of the recorder's channel position on which the Guide Program number's broadcast is received. Then press OK or PUSH JOG . ● If the satellite broadcast is received on your recorder's auxiliary channel "L-1", select "[...]

26 EN G-CODE 12345678 [0 – 9] = [ CANCEL ] : DELETE [PROG] : EXIT ACCESS G-CODE SCREEN 1 Press PROG. . ENTER G-CODE NUMBER 2 Press the NUMBER keys to enter the G- CODE number of a programme you wish to record. ● If you make a mistake, press CANCEL and input the correct number . ACCESS G-CODE PROGRAM SCREEN 3 Press OK , and the G- CODE Program s[...]

EN 27 RETURN TO NORMAL SCREEN 5 Press PROG. or OK . "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. ● Repeat steps 1 – 5 for each additional programme. ENGAGE RECORDER’S TIMER MODE 6 Press TIMER . The recorder turns off automatically and ‰ appears on the display panel. ● T o disengage t[...]

28 EN 123 456 7 89 0 2 4 1 3 Express Timer Pr ogramming Remember , the clock must be set before you can programme the timer ( Z pg. 10). Before performing the following steps: ● Insert a cassette with the safety tab in place. The recorder will come on automatically . ● T urn on the TV and select the VIDEO channel (or A V mode). ● Select the a[...]

EN 29 123 456 7 89 0 2 4 1 3 SET T APE SPEED 7 Press (SP/LP/EP) to set the tape speed. RETURN TO NORMAL SCREEN 8 After confirming all information is correct, press PROG. or OK . "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. ● Repeat steps 1 – 8 for each additional programme. ENGAGE RECORDER[...]

30 EN TIMER RECORDING (cont.) Check, Cancel And Replace Programmes DISENGAGE TIMER MODE 1 Press TIMER , then press . ACCESS PROGRAMME CHECK SCREEN 2 Press PROG. CHECK . ACCESS PROGRAMME SCREEN 3 Press PROG. CHECK again to check more informa- tion. Each time you press PROG. CHECK , the next programme's information appears. T o cancel or r eplac[...]

EN 31 Auto Timer When the Auto T imer is set to ON the timer is automatically engaged when the recorder power is turned off and automati- cally disengaged when the recorder is powered back on. ACCESS MAIN MENU SCREEN 1 Press MENU . ACCESS FUNCTION SET SCREEN 2 Press PUSH JOG %fi to place the pointer next to "FUNCTION SET", then press OK [...]

32 EN Remote A/B Code Switching The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A[...]

EN 33 Contr ol Y our TV Using Additional Buttons Use the NUMBER keys, and the button, CANCEL button or TIMER button to select the TV’s channel. ● W ith televisions under Code 01, 02, 03, 05, 07, 15, 16, 22, 23, 26 or 27, the button corresponds to the 1- digit/2-digit entry switching button (often labelled – /– –) of your TV’ s remote co[...]

34 EN 123 456 7 89 0 2 4 1 EDITING Edit T o Or Fr om Another V ideo Recorder Y ou can use your video recorder as the source player or the recording deck. MAKE CONNECTIONS 1 Connect the player’s AUDIO/VIDEO OUT connector to the recorder’ s AUDIO/VIDEO IN connector . ● Use the L connector for monaural connection. SET RECORDING DECK’S INPUT MO[...]

EN 35 123 456 7 89 0 2 4 1 Y ou can use a camcorder as the source player and your video recorder as the recorder . Edit Fr om A Camcorder MAKE CONNECTIONS 1 Connect the camcorder ’ s AUDIO/VIDEO OUT connec- tors to the recorder’ s front panel AUDIO/VIDEO input connectors. ● Use the L connector for monaural connection. ● When a Master Edit C[...]

36 EN Audio dubbing replaces the normal audio sound of a previously recorded tape with a new soundtrack. Audio Dubbing Original sound AUDIO OUT Audio mixer MAKE CONNECTIONS 1 Connect an audio component to the AUDIO L + R connectors on the recorder's front panel. ● When connecting monaural equipment, use only the recorder's AUDIO L conne[...]

EN 37 NOTES: ● When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to hear the mixed sound (Hi-Fi + Normal soundtracks), press AUDIO on the remote control to select " + (L+R)+NORM" ( Z pg. 15). ● Audio dubbing stops automatically when the counter reaches "0:00:00", and[...]

38 EN 123 456 7 89 0 2 4 1 3 Insert editing replaces part of the recorded scene with new material. Both the picture and Hi-Fi audio soundtrack are replaced with new ones, while the normal audio soundtrack remains unchanged. If you wish to change the normal audio track as well, use the audio dubbing function simultaneously . Use your video recorder [...]

EN 39 123 456 7 89 0 2 4 1 3 ENGAGE INSER T EDITING 6 Press INSERT . ● Y our recorder enters the Insert-Pause mode. (" ", " " and " " light up on the front display panel.) ● The TV screen changes from the still picture to the input source you are going to record. ST AR T EDITING 7 Load the source cassette and play [...]

40 EN COLOUR SYSTEM AUTO NTSC 3.58 NTSC 4.43 NTSC PAL* PAL MESECAM INFORMA TION ON MUL TI-SYSTEM COMP A TIBILITY Setting Of The Colour System Select Buttons Use the COLOUR SYSTEM button on the front panel to select the colour system. Pressing this button changes the mode as illustrated on the left. The On-Screen display will show which mode is sele[...]

EN 41 Playback This recorder can play back all 4 types of recorded tape. VIDEO OUT AUDIO OUT RF OUT NTSC 4.43 MHz NTSC PAL MESECAM PAL MESECAM NTSC [ PAL NTSC 3.58 MHz PAL SECAM NTSC 3.58 NTSC 4.43 PAL (B/G, D/K, I) NTSC (M) Recorded tape Playback cir cuit Manual switching Manual switching Multi-system receiver Multi-system monitor NOTES: When view[...]

42 EN 123 456 7 89 0 2 4 1 3 T urn on the TV and select the VIDEO channel (or AV mode). TUNER SET ACCESS TUNER SET SCREEN 3 Press PUSH JOG % fi to place the pointer next to "TUNER SET", then press OK or PUSH JOG . SELECT AUTO CH SET MODE 4 Press PUSH JOG % fi to place the pointer next to "AUT O CH SET", then press OK or PUSH J[...]

EN 43 Manual Channel Set Store channels that were not stored during Auto Set Up ( Z pg. 6 ) or Auto Channel Set ( Z pg. 42). ACCESS TUNER SET SCREEN 1 Perform steps 1 – 3 of "Auto Channel Set" on page 42. ACCESS CHANNEL LIST 2 Press PUSH JOG %fi to place the pointer next to "CH EDIT", then press OK or PUSH JOG . SELECT POSITI[...]

44 EN TUNER SET (cont.) Delete A Channel ACCESS TUNER SET SCREEN 1 Perform steps 1 – 3 of "Auto Channel Set" on page 42. ACCESS CHANNEL LIST 2 Press PUSH JOG %fi to place the pointer next to "CH EDIT", then press OK or PUSH JOG . SELECT CHANNEL 3 Press PUSH JOG %fi to until the channel you want to delete begins blinking. DEL[...]

EN 45 Fine-T uning Channels ACCESS TUNER SET SCREEN 1 Perform steps 1 – 3 of "Auto Channel Set" on page 42. ACCESS CHANNEL LIST 2 Press PUSH JOG %fi to place the pointer next to "CH EDIT", then press OK or PUSH JOG . SELECT CHANNEL TO FINE-TUNE 3 Press PUSH JOG %fi until the channel you want to tune begins blinking, then pre[...]

46 EN TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair . POSSIBLE CAUSE ● The mains power cord is discon- nected. ● “ ‰ “ is displayed on the disp[...]

EN 47 CORRECTIVE ACTION Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed. Set to the desired channel. Confirm that the source is properly connected. Confirm that all units’ power switches are turned on. Set the input mode to “L-1” or “F-1”. Confirm that the camcorder is properly connected. Set the input[...]

48 EN CORRECTIVE ACTION Position the camcorder so its microphone is away from the TV . T urn the TV’s volume down. If you need the skipped channels, restore them ( Z pg. 43). Press P AUSE to pause the recording, change channels, then press PLA Y to resume recording. Perform manual setting again. Connect the TV aerial cable to the recorder properl[...]

EN 49 QUESTIONS AND ANSWERS PLA YBACK Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes to protect the heads. Q. When returning from multi-speed search to no[...]

50 EN INDEX FRONT VIEW REW INSERT A.DUB/SIMUL FF JOG SHUTTLE COLOUR SYSTEM SPATIALIZER POWER VIDEO (MONO) L –AUDIO– R SP/LP/EP 3R PICTURE TV PROG + TV PROG – S L O W S L O W REVIEW SP + 8 4 0 6 15dB NORM 1 2 3 $ * & ^ % 9 ! 0 4 5 6 7 # 8 @ 1 POWER Button Z pg. 8 2 COLOUR SYSTEM Button Z pg. 40 3 SP A TIALIZER Button Z pg. 15 4 Cassette Lo[...]

EN 51 DISPLA Y P ANEL 1 B.E.S.T . Picture System Display Z pg. 22 Audio Level Indicator 2 Symbolic Mode Indicators 3 "T imer" Indicator Z pg. 27 4 Channel Display Clock Display 5 T ape Speed Indicators Z pg. 18 6 Instant REVIEW Indicator Z pg. 14 7 Audio Mode Indicator Z pg. 15 8 "Cassette Loaded" Mark 9 Counter Display 0 Mode D[...]

52 EN INDEX (cont.) REMOTE CONTROL Buttons with a small dot on the left side of the name can also be used to operate your TV Z pg 33. 1 TV Button Z pg. 33 2 VCR Button Z pg. 33 3 TV/VCR Button Z pg. 33 4 REVIEW Button Z pg. 14 5 NUMBER Keys Z pg. 18 6 CANCEL Button Z pg. 30 Counter [C.] RESET Button Z pg. 19 7 ST OP +/– Button Z pg. 28 8 ST AR T [...]

EN 53 SPECIFICA TIONS GENERAL Power requirement Rating : AC 1 10 – 240 V ` , 50/60 Hz Operating : AC 0 90 – 260 V ` , 50/60 Hz Power consumption : 22 W T emperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 400 x 94 x 347 mm W eight : 3.8 kg Format : VHS standard Maximum reco[...]

MEMO[...]

MEMO[...]

EN COPYRIGHT © 1998 VICTOR COMPANY OF JAPAN, LTD. MS Printed in Malaysia 0798CKV * UN * PJ V ICTOR COM P ANY OF JAPAN, LIMITED HR-DD857MS[...]