JVC RX-1024VBK Bedienungsanleitung

For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No. LVT0018-001A [J] INSTRUCTIONS RX-1024VBK AUDIO/ VIDEO CONTROL RECEIVER – + RX-1024V AUDIO/VIDEO CONTROL RECEIVER POWER VIDEO STANDBY SPEAKERS 12 PHONES [...]

G-1 W arnings, Cautions and Others Caution –– POWER switch! Disconnect the mains plug to shut the power off completely. The POWER switch in any position does not disconnect the mains line. The power can be remote controlled. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERV[...]

G-2 To get the best DSP (Digital Signal Processor) effect in your listening room, note the speaker settings you have set on the table below for future reference (even though the receiver memorizes the settings until you change them). For actual setting procedures, see pages 19 to 21. Speakers Setting Front Speakers LARGE SMALL Center Speaker LARGE [...]

1 T able of Contents Parts Identification ...................................................................................... 3 Getting Started ........................................................................................... 4 Before Installation .........................................................................................[...]

2 Using the DSP Modes ................................................................................ 28 Using the 3D-PHONIC Modes ............................................................................................................................................. 29 Using the D AP Modes ....................................................[...]

3 TV/CATV/ DBS VCR 1 POWER VCR 1 VCR 2 VIDEO CD TAPE/MD PHONO TV/DBS AM MODE SURROUND CNTR TONE CNTR –+ DIGITAL/ ANALOG INPUT CHANNEL – + VOLUME – + DISC MUTE +10 100+ 10 FM 1 SLEEP POWER POWER AUDIO 2 3 TEST REAR · L AUDIO/ TV/VCR CATV DBS REAR · R –+ 456 EFFECT SEA MODE RETURN FM MODE/ MUTE –+ SUBWOOFER –+ 7 /P 8 0 9 ENTER MENU MENU[...]

4 Getting Star ted This section explains how to connect audio/video components and speakers to the receiver , and how to connect the power supply . Before Installation General • Be sure your hands are dry . • T urn the power of f to all components. • Read the manuals supplied with the components you are going to connect. Locations • Install[...]

5 AM EXT AM LOOP GND FM 75 FM GND ANTENNA 2 3 1 4 3 4 2 1 Connecting the FM and AM Antennas FM Antenna Connections Notes: • Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception. • If reception is poor , connect an outdoor single vinyl- cov ered wire to the AM EXT ter[...]

6 Connecting the Speakers Y ou can connect the following speakers: • T wo pairs of front speakers to produce normal stereo sound. • One pair of rear speakers to enjoy the surround ef fect. • One center speaker to produce more ef fectiv e surround effect (to emphasize human voices). • One subwoofer to enhance the bass. IMPORTANT : After conn[...]

7 Connecting the rear and center speakers Connect the rear speakers to the REAR SPEAKERS terminals and a center speak er to the CENTER SPEAKER terminals. Connecting the subwoofer speaker Connect the input jack of a po wered subwoofer to the SUBWOOFER jack on the rear panel, using a cable with RCA pin plugs. T o enhance your audio system Y ou can us[...]

8 Connecting Audio/V ideo Components Y ou can connect the following audio/video components to this recei ver . Refer also to the manuals supplied with your components. If you want to connect a component not listed in the table belo w , refer to the manual supplied with it. Analog connections A udio component connections Use the cables with RCA pin [...]

9 V ideo component connections Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the video jack. If your video components hav e S-video (Y/C-separation) terminals, connect them using S-video cables (not supplied). Connecting these video compo[...]

10 – + RX-1024V AUDIO/VIDEO CONTROL RECEIVER POWER VIDEO STANDBY SPEAKERS 12 PHONES DOLBY SURROUND DSP MODE BALANCE/SURROUND ADJUST SEA MODE SEA ADJUST SETTING MULTI JOG MASTER VOLUME SOURCE SELECTOR S-VIDEO VIDEO AUDIO LR DIGITAL INPUT FM/AM TUNING TUNER PRESET TUNER/SEA MEMORY FM MODE DVD TV SOUND/DBS PHONO TAPE/MD VCR 1 VCR 2 FM AM VIDEO CD SO[...]

11 DVD DIGITAL IN DIGITAL 3 (CD) DIGITAL 2 (DVD) DIGITAL 1 (DBS) PCM/DOLBY DIGITAL DBS Getting Star ted Digital connections This recei ver is equipped with three DIGIT AL IN terminals — one digital coaxial terminal and two digital optical terminals. T o enjoy Dolby Digital, you hav e to connect the source components using the DIGIT AL IN terminal[...]

12 Notes: • A small amount of pow er is alwa ys consumed ev en in standb y mode. T o switch off the power completely , unplug the power cord from the A C outlet. • If the pow er cord is unplugged or a power f ailure occurs, preset settings will be erased in a f ew da ys. CAUTIONS: • Do not touch the power cord with wet hands . • Do not pull[...]

13 Basic Operations The following operations are commonly used when you play any sound source. IMPORTANT : When using the Remote Control, check to see if its remote control mode selector is set to the correct position: T o operate an audio system, TV , and VCR, set it to “ A UDIO/TV/ VCR. ” T o operate a CA TV conv erter , set it to “CA TV . [...]

14 Fr om the remote contr ol: Press one of the sour ce selecting buttons dir ectly . D VD Selects the D VD player . VCR1 Selects the video component connected to the VCR1 jacks. VCR2 Selects the video component connected to the VCR2 jacks. VIDEO Selects the video component connected to the VIDEO jacks. CD* Selects the CD player . T APE/MD* Selects [...]

15 Basic Operations Selecting the Front Speakers On the front panel only : When you hav e connected two pairs of the front speakers, you can select which to use. Press SPEAKERS 1 or SPEAKERS 2 to select the speak er to use. Each time you press the button, the lamp on the respecti ve b utton turns on and off. When the lamp on either button lights up[...]

16 Attenuating the Input Signal When the input le vel of the playing source through the analog terminals is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal le vel to prev ent the sound distortion. On the front panel only : Press and hold SOUND SELECT/INPUT A TT until “INPUT A TT ON” appears on the[...]

17 Basic Settings Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier . IMPORTANT : When using the Remote Control, check to see if its remote control mode selector is set to the correct position: T o operate this recei ver , set it to “ A UDIO/[...]

18 BALANCE /SURROUND ADJUST MULTI JOG LOUDNESS SOURCE NAME SETTING MULTI JOG Adjusting the Front Speaker Output Balance If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance. On the front panel only : 1. Pr ess BALANCE/SURR OUND ADJUST repeatedly until “L/R BALANCE” appears on the d[...]

19 Digital Input (DIGITAL IN) T erminal Setting When you use the digital input terminals, you hav e to register what components are connected to which terminals (DIGIT AL IN 1/2/3). On the front panel only : 1. Pr ess SETTING repeatedly until “DIGIT AL IN” appears on the display . The display changes to sho w the current setting. 2. T urn MUL T[...]

20 Center Delay T ime Setting Register the delay time of the sound from the center speak er , comparing that of the sound from the front speakers. If the distance from your listening point to the center speaker is equal to that to the front speakers, select 0 msec. As the distance to the center speaker becomes shorter , increase the delay time. On [...]

21 Basic Settings CROSS: 80Hz CROSS:100Hz CROSS:120Hz Note: This function tak es effect only when playing back a sources using the Dolby Digital. LFE ATT: 0dB LFE ATT:10dB SETTING MULTI JOG SETTING MULTI JOG COMP.: OFF COMP.: MID COMP.: MAX Note: This function tak es effect only when playing back a sources using the Dolby Digital. 2. T urn MUL TI J[...]

22 One T ouch Operation This receiver can memorize the optimum sound settings for each playing source. About the One T ouch Operation JVC’ s One T ouch Operation function is used to assign and store dif ferent sound settings for each different pla ying sour ce. By using this function, y ou do not have to change the settings ev ery time you change[...]

23 Receiving Radio Br oadcasts Y ou can browse through all the stations or use the preset function to go immediately to a par ticular station. IMPORTANT : When using the Remote Control, check to see if its remote control mode selector is set to the correct position: T o operate this r eceiver , set it to “ A UDIO/TV/VCR” (except when selecting [...]

24 5. Repeat steps 1 to 4 until y ou store all the stations y ou want. T o erase a stored preset station Storing a ne w station on a used number erases the previously stored one. T o tune in a preset station On the front panel: 1. Pr ess TUNER PRESET . 2. T urn MUL TI JOG to select a preset channel. From the r emote control: 1. Pr ess FM or AM. 2. [...]

25 Assigning Names to Preset Stations Y ou can assign a name of up to four characters to each preset station. When a preset station is tuned in, its assigned name will appear on the display . On the front panel only : 1. T une in a preset station. See page 24 for details. 2. Pr ess TUNER/SEA MEMORY . The preset channel number starts flashing for ab[...]

26 Using the SEA Modes The SEA (Sound Effect Amplifier) modes give you control of the way your music sounds. IMPORTANT : When using the Remote Control, check to see if its remote control mode selector is set to the correct position: T o operate this recei ver , set it to “ A UDIO/TV/VCR” (e xcept when selecting the DBS tuner as the source). Sel[...]

27 Creating Y our Own SEA Mode Y ou can adjust and store your own SEA adjustment into memor y (SEA USERMODE). On the front panel only : If you do not want to store your adjustment, b ut rather want to adjust the SEA temporarily , skip step 4 below . 1. Pr ess SEA ADJUST r epeatedly until the frequency range (100Hz, 1kHz or 10kHz) you want appears o[...]

28 Using the DSP Modes The built-in Surround Processor provides three types of the DSP (Digital Signal Processor) mode — 3D- PHONIC mode, DAP (Digital Acoustic Processor) mode and Surround mode (Dolby Digital, Dolby Pro Logic and JVC’ s Theater Surround.) On the 3D-PHONIC mode The 3D-PHONIC mode gi ves you such a nearly surround ef fect as it i[...]

29 Using the DSP Modes IMPORTANT : When using the Remote Control, check to see if its remote control mode selector is set to the correct position: T o operate this recei ver , set it to “ A UDIO/TV/VCR” (except when selecting the DBS tuner as the source). Using the 3D-PHONIC Modes When using the 3D-PHONIC modes, you need only two front speak er[...]

30 4. Pr ess BALANCE/SURR OUND ADJUST repeatedly until “DSP EFFECT” appears on the display . The display changes to sho w the current setting. 5. T urn MUL TI JOG to select the effect level, while the indication of the pre vious step is still on the display . As you turn it, the ef fect lev el changes as follows: As the number increases, the se[...]

31 Fr om the remote contr ol: 1. Select and play the sour ce encoded with Dolby Digital (bearing the mark DIGITAL ) or with Dolby Surround (bearing the mar k DOLBY SURROUND ). • When you play back the source encoded with Dolby Digital and select the digital input for that source, the Ÿ DIGIT AL indicator lights up on the display . 2. Pr ess SURR[...]

32 Using the DAP Modes Y ou can use fi ve D AP modes — “Li ve Club, Dance Club, Hall, Pa vilion, and Headphones” for any source. Among the D AP modes, “Headphones” is very special. It can create the same stereo sound as you listen through the speakers of f air while listening to a source using headphones. So, you can feel as if you were n[...]

33 4. Adjust the effect le vel. 1) Pr ess BALANCE/SURR OUND ADJUST r epeatedl y until “DSP EFFECT” appears on the display . 2) T urn MUL TI JOG to select the effect le vel, while the indication of the pre vious step is still on the display . As you turn it, the ef fect level changes as follo ws: As the number increases, the selected D AP mode b[...]

34 Using the Dolby Digital and Dolby Pro Logic Modes Once you hav e adjusted the Dolby Digital and Dolby Pro Logic modes, this receiv er memorizes adjustment for each mode. T o activ ate the Dolby Digital and Dolby Pro Logic modes, follo w the procedure below . From the r emote control: 1. Select and play the sour ce encoded with Dolby Digital (bea[...]

35 4. Pr ess TEST to start checking the speaker output balance. “TEST T ONE L” starts flashing on the display , and a test tone comes out of the speakers in the follo wing order: IMPOR T ANT : • Output the test tone while playing back an audio source. With the DVD digital input selected as the source, no test tone may come out while no signal[...]

36 Notes: • T o enjo y the software encoded with Dolb y Digital, you must connect the source component using the digital terminal on the rear of this receiv er . • When the signals come into this receiver through the analog connection from the source component, “PRO LOGIC” is automatically selected. • The Surround mode is not used with th[...]

37 Using the Theater Surr ound Mode Once you hav e adjusted the Theater Surround mode, this recei ver memorizes the adjustment. T o activ ate the Theater Surround mode, follo w the procedure below . From the r emote control: 1. Select and play the sour ce encoded with Dolby Digital (bearing the mark DIGITAL ) or with Dolby Surround (bearing the mar[...]

38 5. Adjust the speaker output le vels as f ollows: • T o adjust the center speaker lev el, press CNTR +/–. • T o adjust the left rear speaker le vel, press REAR•L +/–. • T o adjust the right rear speaker lev el, press REAR•R +/–. 6. Pr ess TEST again to stop the test tone. 7. Pr ess CNTR T ONE to select the center tone level y ou [...]

39 Notes: • T o enjoy the softw are encoded with Dolby Digital, y ou must connect the source component using the digital terminal on the rear of this receiver . • The Surround mode is not used with the other DSP modes such as the DAP mode and 3D-PHONIC mode. When the Surround mode is turned on, the other DSP mode, if used, will be turned off. O[...]

40 5. Pr ess BALANCE/SURR OUND ADJUST repeatedly until “CENTER TONE” appears on the display . The display changes to sho w the current setting. 6. T urn MUL TI JOG to select the center tone level y ou want, while the indication of the pre vious step is still on the display . The center tone adjustment aff ects the mid-frequency range, which the[...]

41 MAIN MENU SOURCE : ch 1 FM 87.5 MHz VISUAL :VCR1  MODE :OFF  SOUND CONTROL TUNER CONTROL SETTING    VOLUME : 20 :OPERATE * * * * * * * * * * * * Using the On-Scr een Menus Y ou can use the menus on the TV screen to control the receiver . T o use this function, you need to connect the TV to the MONITOR OUT jack on the r[...]

42 Adjusting the Front Speaker Output Balance (Also see page 18) 1. Pr ess any button of ON SCREEN CONTR OL % / fi / @ / # once. The MAIN MENU appears on the TV . 2. Pr ess ON SCREEN CONTROL % / fi to move to “SOUND CONTR OL, ” then press @ / # . The SOUND CONTR OL menu appears on the TV . 3. Pr ess ON SCREEN CONTROL % / fi to move to “B A[...]

43 MAIN MENU SOUND CONTROL menu MAIN MENU SOURCE : ch 1 FM 87.5 MHz VISUAL :VCR1  MODE :OFF  SOUND CONTROL TUNER CONTROL SETTING    VOLUME : 20 :OPERATE * * * * * * * * * * * * SOUND CONTROL SURROUND LEVEL SEA  BAL.:R-21  LOUDNESS : OFF INPUT ATT : NORMAL SUBWFR LEVEL: 0 dB   NEXT PAGE :OPERATE * *[...]

44 F or Dolby Surround Pro Logic: “TEST T ONE”: Output a test tone. “CENTER LEVEL”: Adjust the center speaker output lev el. ** “REAR L LEVEL”: Adjust the left rear speaker output le vel. * “REAR R LEVEL”: Adjust the r ight r ear speak er output lev el. * “CENTER T ONE”: Select the center tone lev el. ** F or Dolby Digital: “T[...]

45 Using the On-Scr een Menus MAIN MENU SOUND CONTROL menu SEA menu SEA ADJUST menu MAIN MENU SOURCE :VCR1 VISUAL :VCR1  MODE :OFF  SOUND CONTROL TUNER CONTROL SETTING    VOLUME : 20 :ENTER * * * * * * * * * * * * SOUND CONTROL SURROUND LEVEL SEA  BAL.:CNTR  LOUDNESS : OFF INPUT ATT : NORMAL SUBWFR LEVEL[...]

46 4. Pr ess ON SCREEN CONTROL @ / # to set (or adjust) the setting item selected in step 3. 5. When y ou finish, pr ess EXIT repeatedly until the menu disappears fr om the TV . Operating the T uner 1. Pr ess any button of ON SCREEN CONTR OL % / fi / @ / # once. The MAIN MENU appears on the TV . 2. Pr ess ON SCREEN CONTROL % / fi to move to “TU[...]

47 Using the On-Scr een Menus Assigning Names to the Preset Stations (Also see page 25) 1. Pr ess any button of ON SCREEN CONTR OL % / fi / @ / # once. The MAIN MENU appears on the TV . 2. Pr ess ON SCREEN CONTROL % / fi to move to “TUNER CONTR OL, ” then press @ / # . The TUNER CONTROL menu appears. 3. Pr ess ON SCREEN CONTROL % / fi to mov[...]

48 COMPU LINK Remote Contr ol System The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on the receiver . T o use this remote control system, you need to connect JVC audio components through the COMPU LINK-3 (SYNCHR O) jacks (see belo w) in addition to the connections using cables with RCA pin [...]

49 COMPU LINK – 3 (SYNCHRO) TEXT COMPU LINK 1(MASTER UNIT) 2(SLAVE UNIT) TEXT COMPU LINK Remote Contr ol System The TEXT COMPU LINK remote control system has been newly developed to deal with the disc information recorded in the CD T ext* and MDs. Using these information in the discs, you can operate the CD player or MD recorder equipped with the[...]

50 OPERA TIONS T o use this remote control system, you need to connect the TV to the MONIT OR OUT jack on the rear panel (see page 9), and set the TV’ s input mode to the proper position to which the recei ver is connected. Make sure you have connected the CD player or MD recorder equipped with the TEXT COMPU LINK remote control system. If not, y[...]

51 Searching a Disc (Only for the CD player) Search a disc by its per former: 1. Displa y the disc information screen by f ollowing the procedur e on page 50. 2. Pr ess ON SCREEN CONTROL % / fi to move to “SEARCH, ” then pr ess SET . The DISC SEARCH screen appears on the TV . 3. Pr ess ON SCREEN CONTROL % / fi to move to “PERFORMER”, then[...]

52 5. Pr ess SET again. Disc search starts, then the SEARCH RESUL T screen, sho wing the disc titles, appears. 6. On the SEARCH RESUL T screen, y ou can do the follo wing: • Changing the indication of the disc inf ormation: Press ON SCREEN CONTR OL % / fi to move to a searched disc, then press @ / # . Each time you press @ / # , the disc informa[...]

53 TEXT COMPU LINK Remote Contr ol System Using the User File (Only for the CD Player with the User File Function) Y ou can use the User File function through this receiv er . For the User File function, refer to the manual supplied with your CD player . Using your own User Files: 1. Displa y the disc information screen by f ollowing the pr ocedure[...]

54 Entering the Disc Information For the CD Player with the disc memory function: Y ou can use the disc memory function through this receiv er . The disc information (its performer , disc title, and its music genre) of normal audio CDs will be stored into the memory b uilt in the CD player . For the disc memory function, ref er to the manual suppli[...]

55 7. Pr ess ON SCREEN CONTROL % / fi / @ / # to move to “DISC1: MY F A VORITE (in this example), ” then press SET . The TITLE INPUT : DISC 1 GENRE screen appears. 8. Pr ess ON SCREEN CONTROL % / fi to move to the genre y ou want, then press SET . The Disc Information screen appears again. T o show the unseen genr es, press ON SCREEN CONTROL [...]

56 A V COMPU LINK Remote Contr ol System The A V COMPU LINK remote control system allows you to operate JVC video components (TV , VCR, and DVD player) through the receiver . CAUTION: The A V COMPU LINK remote control system cannot control the DBS tuner connected to the TV/DBS jacks, and video components connected to the VIDEO and VCR2 jacks on the[...]

57 Note: Ref er also to the manuals supplied with your video components. FUNCTIONS: This remote control system allo ws you to use fi ve functions listed below . Remote Control of DVD Player , VCR, and TV Using This Remote Control F or the DVD play er and the VCR: • Aim the remote control directly at the remote sensor on the eac h component. F or [...]

58 IMPORTANT : T o operate JVC’ s audio components using this remote control: • Y ou need to connect JVC audio components through the COMPU LINK-3 (SYNCHR O) jacks (see page 48) in addition to the connections using cables with RCA pin plugs (see page 8) or using digital cables (see page 11). • Aim the remote control directly at the remote sen[...]

59 CD player -changer After pressing DISC ( with the r emote contr ol mode selector set to “A UDIO/TV/VCR” ), you can perform the follo wing operations on the CD player-c hanger: PLA Y : Starts playing. 4 4 4 4 4 : Returns to the be ginning of the current (or previous) track. ¢ ¢ ¢ ¢ ¢ : Skips to the be ginning of the next track. STOP: Sto[...]

60 IMPORTANT : T o operate JVC’ s video components using this remote control: • Y ou need to connect JVC video components through the A V COMPU LINK jacks (see page 56) in addition to the connections using cables with RCA pin plugs (see pages 9 to 10) or using a digital cable (see page 11). • When using the remote contr ol: – F or the DVD p[...]

61 TV Y ou can always perform the follo wing operations ( with the r emote contr ol mode selector set to “A UDIO/TV/VCR”) : TV/CA TV/DBS POWER: T urns on or off the TV . TV/VIDEO: Sets the input mode (either TV or VIDEO). After pressing TV/DBS ( with the remote contr ol mode selector set to “A UDIO/TV/VCR” ), you can perform the follo wing [...]

62 This remote control supplied with the recei ver can transmit control signals for other manufacturers’ VCRs, TVs, CA TV con verters and DBS tuners. By changing the transmittable signals from preset ones to the other manuf acturers’, you can operate the other manufacturer’ s components using this remote control. When operating the other manu[...]

63 T o change the transmittable signals for operating a CATV converter or DBS tuner 1. F or the CA TV con verter: Set the remote contr ol mode selector to “CA TV . ” F or the DBS tuner: Set the remote contr ol mode selector to “DBS. ” 2. Pr ess and hold TV/CA TV/DBS PO WER. 3. Pr ess TV/DBS. 4. Enter the man uf actur er’ s code (three dig[...]

64 T o change the transmittable signals for operating another manufacturer’s VCR 1. Set the r emote control mode selector to “A UDIO/TV/ VCR. ” 2. Pr ess and hold VCR1 PO WER. 3. Pr ess VCR1. 4. Enter the man uf actur er’ s code (three digits) using b uttons 1 – 9, and 0. See the lists on pages 66 and 67 to f ind the code. 5. Release VCR1[...]

65 Manufacturers’ codes for TV Admiral 093 Aiko 092 Akai 030 Alaron 179 Anam 180 Anam National 055 AOC 019, 030 Audiovox 180 Belcor 019 Bell & Howell 016, 154 Bradford 180 Brockwood 019 Candle 030, 056 Carnivale 030 Carver 054 Celebrity 000 Citizen 030, 039, 056, 060, 092, 280 Concerto 056 Contec 180 Craig 180 Crown 039, 180 Curtis Mathes 030[...]

66 Manufacturers’ codes for CATV converters ABC 003, 007, 008, 011, 013, 014, 017 Allegro 153 Archer 153 Century 153 Citizen 153 Comtronics 040 Contec 019 Everquest 015, 040 Focus 400 Garrard 153 Gemini 015 General Instrument 011, 276 GoldStar 040, 144 Hamlin 009, 020, 259, 273 Hitachi 011 Hytex 007 Jasco 153 Jerrold 003, 011, 012, 014, 015, 276 [...]

67 NEC 038, 041, 067, 104 Nikko 037 Nikon 034 Noblex 240 Olympus 035 Optimus 037, 048, 104, 162 Orion 479 Panasonic 035, 162, 225 Penney 035, 037, 038, 042, 054, 240 Pentax 042 Philco 035 Philips 035, 081 Pilot 037 Pioneer 067 Portland 020 Profitronic 240 Protec 072 Pulsar 039 Quarter 046 Quartz 046 Quasar 035, 162 Radio Shack 000, 037 Radix 037 Ra[...]

68 T r oubleshooting Use this char t to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC ser vice center . PROBLEM The display does not light up. No sound from speakers. Sound from one speaker only. Continuous hiss or buzzing during FM reception. Occasional cracking noise during FM reception. How[...]

69 Specifications Output Power At Stereo operation 130 watts per channel, min. RMS, both channels driven into 8 ohms, 20 Hz to 20 kHz with no more than 0.02% total harmonic distortion. Amplifier Output Power ....................................................... At Surround operation Front Channels .................................................[...]

70 Synchronization .......................................................................................................................................... Negative Signal-to-Noise Ratio .......................................................................................................... ....................... 45 dB On-Screen Color System .[...]

G-3 Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of the wide array of JVC products, service is the key to maintaining the high level of performance for which JVC is world famous. The JVC service and engineering organization stands behind our products. NATIONAL HEADQ[...]

G-4 PARTS LABOR 2 YRS 2 YRS LIMITED W ARRANTY AUDIO-2 JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP from the date of original retail purchase for the period as shown below. (“The Warranty Period.”) THIS LIM[...]

VICTOR COMP ANY OF JAP AN , LIMITED 0598OFMMDWJEM EN J V C Cover.RX-1024V[J]/1.PM5 98.5.12, 0:14 PM 2[...]