Lennox Hearth Products Brentwood SP Bedienungsanleitung

EP A W ood -Bu rni ng Fir epl ace s P/N 8 50, 039 M REV . G 1 1/2 008 BRENTWOOD SP MODEL BRENTWOOD™ This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and understand these instructions before beginning your installation. Do not alter or modify the fireplace or [...]

W ARNING T o avoid the risk of damaging fireplace materials and increas- ing the risk of fire, do not use the fireplace to cook or warm food. IMPORT ANT! GENERAL SAFETY PRECAUTIONS. READ AND UNDERST AND THESE SAFETY R U L E S B E F O R E Y O U R F I R S T F I R E . IMPOR T ANT Wh en b urn in g wo od , us e SO LI D NA TU RAL DR Y WE LL -SE AS ONE[...]

T ABLE OF CONTENTS Safety Rules and Specifications for Mobile or Manufactured Home Installation ......................... Page 2 Introduction ...................................... Page 3 Parts Required ................................. Page 3 Optional Equipment ........................... Page 3 Operating The Fireplace .................... Page 3[...]

Building a Fire (starting and maintaining a fire) T o start a fire, place several crumpled up balls of newspa per in the firebox. Place small dry pieces of kindling on top of the paper , criss-crossing the kindling so that there are air spaces in be- tween. Keep the fuel far back enough so that air can get underneath. Open the air controls fully[...]

B. Blowers operating (e.g.: range hood) These blowers draw air out of the house and may actually cause a negative pressure in the house. T urn off all blowers and open a nearby window to determine if this is the cause of the problem. C. Wet wood W et or tarred wood will smoulder and smoke instead of burn properly . D. Dirty or blocked chimney Check[...]

REFRACTORY REPLACEMENT The intense heat of the fire will normally cause hairline cracks in the refractor y . These cracks can be minimized by proper curing as described in “First Fires”. They will not normally dimin- ish the effectiveness of the refractor y . If large cracks develop, then the refractor y should be replaced. T o replace the ref[...]

GLASS CARE Glass Replacement The glass used for the Brentwood™ fireplace is a high temperature ceramic glass (1,400° F). If the glass breaks, it must be replaced with an identical ceramic glass. T empered glass or ordinary glass will not withstand the high temperatures of the Brentwood fireplace. Replacement glass should be purchased from a Le[...]

Framing, Facing And Mantel The construction of the framing, facing, and mantel must be in accordance with the stan- dards and the following illustrations ( Figure s 7a, 7b and 8 ): A. Frame the fireplace using 2” x 3” or heavier lumber . B. WARNING: Combustible materials cannot be used in the space directly above the fireplace, except for the[...]

C om b u s ti b l e ma t er i a ls c a n N O T be us e d i n t he s p ac e di re c tl y ab ov e t h e fi re p la c e . D o n ot fi l l t h e sp a ce a bo ve th e fir ep l ac e wi th an y m at e r i al ( Ex ce p t t h e wo o d f r am in g ) F 19 -3 /3 2” J 20-1/2” E 7’ Min. 2” x 3’ Min. D Fireplace Framing Header B A OUTSIDE CHASE G H C[...]

Facing 1. Combustible material must be installed flush with the fireplace. It may not project in front of and on the fireplace (i.e. the steel facade of the fireplace) ( Figure 10 ) . 2. Non-combustible materials such as brick, stone or ceramic tile may project in front of and onto the fireplace facing ( Figure 11 ) . Mantel The mantel must be[...]

HOT AIR DUCTING INST ALLA TION The Brentwood™ fireplace is approved for use with a Gravity Kit. Gravity Kit The gravity kit is designed for double hot air out- lets and includes: (See Figures 12 and 13 ) - 2 telescopic lengths 8” I.D. - 2 90º elbows 8” I.D. - 2 hot air outlet kits (grill and frames) - 2 adaptors See Gravity Kit Accessories [...]

6- 1/2 ” Mi n. (t o c ei li ng) Figure 13 Figure 14 Flashing Collar Rain Cap Roof Support Attic Radiation Shield Radiation Shield (Firestop) Non-Combustible Facing Maintain at least 6-1/2” (160 mm) clearance from the outlet grill framing to a combustible ceiling, side wall or mantel. Ou tle t Gri ll Ou tle t Gri ll WARNING: The outlet grills sh[...]

The duct system must be installed respecting the following: 1. Remo ve the plat es clo sing up the 8” dia. hol es on top of the fireplace. Then, cut the insula- tion in order to obtain two 8” dia. openings. Fix the adaptors on the fireplace openings by turning clockwise ( Figure 12 ) . 2. Maintain at least a 2” (50 mm) clearance between the[...]

6. The chimney must extend at least three (3) feet (915 mm) above its point of contact with the roof and at least two (2) feet (610 mm) higher than any wall, roof or building within ten (10) feet (3m) of it ( Figure 17 ) . 7. If the chimney extends higher than five (5) feet (1,500 mm) above its point of contact with the roof, it must be secured us[...]

CHIMNEY INST ALLA TION INSTRUC- TIONS 1. Cut and frame the holes in the ceiling, floor and roof where the chimney will pass (see Figure 18 ). Use a plumb-bob to line up the center of the holes. The sizes are indicated in T able 2 for the floor and ceiling holes and T able 3 ( Page 13 ) for the roof holes. 2. From below , install a firestop in ea[...]

Roof Down Slope Hole Size S LO P E A SH T / H T 6 1 03 + S -2 1 0 0 + / H T6 0 0 0 + A C R oo f P it c h 6 ” 6 ” 6 ” 0 * 1 2- 3 / 8 ” ( 3 1 4 m m ) 1 4- 1 / 8 ” ( 3 5 9 m m ) 1 5” ( 38 0 m m) 2 /1 2 1 2- 9 / 1 6” ( 3 19 m m ) 1 4- 3 / 8 ” ( 3 6 5 m m ) 1 5 3 / 8 ” ( 3 9 0 m m ) 4 /1 2 1 3” ( 3 30 m m ) 1 4 -7 / 8 ” ( 3 7 8 m m[...]

Ch imn ey 6” Elbo w Offset & Height One Length Between Elbows T wo Lengths Between Elbows 8” 12” 18” 24” 36” 48” 8” & 48” 1 2” & 4 8” 1 8 ” & 48 ” 2 4” & 4 8 ” 36” & 48” 48” & 48” Se cu re T emp AS HT No va T emp HT 61 03 + 15º A 3- 5/ 16 ” (8 4m m) 4- 5/ 16 ” (1 10 mm) 5- 7/ 8?[...]

ANGLED WALL RADIA TION SHIELD (RSM+ and RSMI30) When traversing a combustible wall with the chimney at a 30º or 45º angle, an angled firestop or wall radiation shield must be installed. Only one is required. Note: 45º angle for Canada only ( RSMI45) In cold climate locations (climates where temperatures will fall below 32° F / 0° C), we recom[...]

CHIMNEY SUPPORT INST ALLA TION Universal Roof Support This support has three possible uses: 1. For ASHT / HT6103+ and S-2100+ / HT6000+, it must be used on a roof to support the chimney . 2. It may be used on a floor , ceiling or roof above an offset to support the chimney above the offset. 3. It may be used on a floor , ceiling or roof as a supp[...]

Follow these steps: 1- Position the fireplace in its location. T emporarily install the ASHT elbow on the top of the fireplace and, using a level, mark with an oval the location where the flue liner will enter the masonry chimney . 2- In the middle of the oval, drill a hole in the masonr y chimney at 30º. 3- Increase the size of the hole until [...]

Installation Accessories Description Cat./Part No. (Required - Order Separately) Black Cast Iron Door for Brentwood ™, BWBK H0516 Gold Plated Cast Iron Door for Brentwood, BWG H0517 Brushed Nickel Cast Door for Brentwood, BWBN H4849 Outside Air Kit (Required - Included With Fireplace) Outside Air Coupler to connect outside air UZI to fireplace, [...]

(AC) Air -Cooled Chimney System* 6” I.D. and 11” O.D. Air Cooled, Stainl. Steel inner and zinc coated steel exterior AC Starter Adaptors One of the following adaptors is required if installing an AC chimney system * AC Ch im ne y is N OT r ec om me nd ed a t el ev at io ns ab ov e 4 ,0 00 fe et o r in co ld c li ma te s ( cl im at es w he re t [...]

CLEARANCE TO COMBUSTIBLES The following clearances meet the minimum requirements for a safe installation: Side wall: 17” (324 mm) measured from the fireplace side. Ceiling: 6’ 8” (2,032 mm) measured from the base of the fireplace. Fireplace enclosure: Bottom : 0” Side: 0” to spacer Back: 0” to spacer T op: Do not fill the space above[...]

Printed in Canada © 2006 Lennox Hearth Products P/N 850,039M REV . G 11/2008 24 Y our Fireplace's Model Number ________________________________________ Y our Fireplace's Serial Number ________________________________________ The Date On Which Y our Fireplace Was Installed ___________________________ Y our Dealer's Name _____________[...]