LevelOne PLI-3510 Bedienungsanleitung

LevelOne PLI- 3510 200Mbp s Powerline Adapt er with Main s P ass - Throu gh User Manual[...]

Table of Co ntents Chapter 1 – Introduction ................................................................................................................. 1 1.1 Overview ........................................................................................................................... 1 1.2 Specification ...............................[...]

1 Chapt er 1 – Introdu ction 1.1 Overview The LevelOne PLI - 3510 operates on HomePlug A V standard, providing up to 200 Mbps data speed over the ex ist ing household pow er supply . This Prod uct is cost- ef f ective , easy to create a home network without spending time and money to run expensiv e C A T5 cabling . Powerline Device is the best so[...]

2 Chapt er 2 – Installa tion & Uninstallatio n Connecti on of Pow erline Ether net A da pter 2. 1 Insta ll ing Power line Device 1. If you have the SINGLE PACKAGE of Powerline,Connect the supplied RJ45 Ethe rnet cable from your PC's E t hernet port t o the Pow er line Ethernet Adapter's LAN Ports or connect the supplied RJ45 Etherne[...]

3 2.2 Ins tallat ion of Pow erline Util ity Th e Configurat ion Utility enables the us ers to identify HomePlug devices on the Powerline network; m easures data rate per f ormance, ensures privacy and performs diagnostics by setting user defined secure Powerline netw orks. Users are requested to v erif y that no other Encr yption M anag ement Utili[...]

4 4. Click “ Set up ” button to continue. 5. Click “ Next ” button t o continue. 6. Click “ I Agree & Ne xt ” button to continue.[...]

5 7. Click “ Next ” button to continue. 8. Click “ Close ” but t on t o exit .[...]

6 9. In order to start the utili ty, double - click the utility icon on desktop. 10. You can see your device working well . The t op p anel of the screen shot show s a Homeplug device connected locally to your computer. The bottom panel shows one device connected remo t ely to the computer runnin g the utility.[...]

7 2.3 Un i nstallation of Configur ation Uti lit y 1. To uninstall the Configuration Utility , g o t o th e “ Control Panel ” of you r syst em . 2. Open the “ A dd/Remo ve Programs ” . 3. Select and double click on the “ Powerline Uti li ty ” in the Add/Remove Programs Properties . 4. Follow the on screen instructions to uninstall the P[...]

8 Chapter 3 – Configur atio n Utili ty Setup Introduction The Configuration Utility enables the users to identify HomePlug devices on the pow er l ine network, measures data rate performance, ensures privacy and performs diagnostics by setting user defined secure powerline networks. The Utility will use a Gra phical User Int erface (GU I) with li[...]

9 The M ai n screen provides a list of all powerline devices logically connected to the computer when the utility is running.T he top pane l shows al l local HomePlug devices connected to the computer’s NIC (Network I nterface Card). In most cases, only one device will be seen. In situations where there are more than one local device being connec[...]

10 above the Remote devices panel showi ng whether the Autoscan functionality i s turned ON or OFF. The followi ng information is displayed for all dev ices t hat appear in the lower panel. Device Name column shows the de fault device name, whi c h may be user re - defined. A user can change the n ame b y e ither using the rename b ut ton or by cl [...]

11 Password column by default is blank and ‘E nter Password’ button can be us ed to enter it . To s et t he Password of the device ( required when c r eating a private netw ork ), first select the device by cli c king on its name in the lower panel and then click on the Enter Pas sword button. A dialog box will appear as show n in Figure 3-3 to[...]

12 Ad d butt o n is used to add a remote dev ice to the existing network by entering the dev ice password of the device. A dialog box wi ll appear as shown below in Figure 3 -4 . The dialog box allows the user to enter both a device name and the password. If a device w as not found, the user will be notified and suggestions to resolve common proble[...]

13 The Scan button is u sed to perform an immediate sear ch of the Ho mePlug devices connected to the Powerline network. By def ault, the utility automatically scans every few seconds and upd ates the display screen. A typical screen after naming and supplying passwords might appear as in Figure 3-5. Figure 3-5 : Main Screen of the Configuration Ut[...]

14 3.2 P r i v a c y Scr een The Privacy screen provi des the user with an option to maintain securit y for their logical network and also to select the devi c es that has to be included in t he ne t work. The a ppearance is shown in Figure 3-6. All HomePlug devices are shipped using a default l ogical network (network name), which is normally “H[...]

15 password’s were not entered, this operation w il l fail and will report a failure message. 3.3 Diagnost ics Screen The Diagnostics screen shows System information and a history of all remote devices seen over a period of time. The appearance is show n in Figure 3-7 . The Upper panel shows technical data concerning software and hardw ar e prese[...]

16 The Lower panel contains a history o f all remote devices seen on the computer over a ce rtain period of time. All devices that were on the powerline netw or k are listed here alon g with a few other parameters. Devices that are active on the current logical netw or k will s how a transfer rate in the Rate c olumn; dev ices on other networks, or[...]

17 Chapt er 4 – Reset an d Netw ork ID Buttons Setting There are 2 buttons on the device, one is Reset button the other is Net wor k ID but to n. 4 .1 Res et Button Push this button can reset to the factory default sett ings. Be careful, when y ou pr ess the reset button, please remove the Ethernet cable ( RJ - 45cable) first, and then press th e[...]

18 Four possi ble scenari os This section describes how t o add and remov e devices using HomePlug AV Simple Connect Technology and covers some o f the technical detail s of how the technology works. Case 1: Forming a Net work Two devices with different network membership k ey (NM K) values are connected to the same powerline. The user wants them t[...]

19 Case 2: Joining a Net wor k In this scenario a network exists. The user wants a new device, the ‘joiner’, to join the network. Any device on the ex isting network can become the ‘adder’. 1. Press the Netw or k I D b utton on the ‘joiner’ f or less than 3 seconds. 2. Press the Netw or k I D button on any network dev ice for less than [...]

20 Case 3: Leaving a Net w ork A network exists. The user w ants to remove one dev ice, the ‘leaver’, from that networ k , for whatever reason. He may want to remove the device from service altogether or have it join another logical network. 1. Press the Network ID but ton on the ‘leav er ’ for at least 10 seconds. The dev ice will reset an[...]

21 Case 4: Join Multiple D evices t o a Net w ork To add several new devices to an ex ist ing network, the p roces s in Case 2 must be repeat ed for each ‘joiner’. A vendor may implement a mode o f operation in which an ‘adder’ dev ice in the network remains in the adder state f or an extended period allow ing additional ‘joiners’ to be[...]