Liebert Universal Monitor Bedienungsanleitung

M ONITORING U NIV ER SAL M ONITOR U SER M ANUAL[...]

[...]

i T ABLE OF CONTENTS 1.0 I NTRODUCTI ON 1.1 Methods of Viewing and Configuring the Universal Monitor . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.2 Data Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.3 Optional Features . . . . . . . . . . . . . .[...]

ii 5.0 W IRING AND C ONNECT IONS - O PTIONAL E XPANSION B OARD 5.1 Wiring Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5.2 Connecting Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.2.1 Connectin[...]

iii 9.5 Setup System - Setup Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 9.5.1 Ide ntify the Sensor as Connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 9.5.2 Change Se nsor Label (Name) . . . . . . . . . . . . . . . . . . . . [...]

iv A PPENDIX A-S ERVICE T ERMINAL I NTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 A.1 Comparison of Functions: LCD and Service Terminal Interface . . . . . . . . . . . . . . . . . . . . . . 85 A.2 Connecting to the Service Terminal In terface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

v FIGURES Figure 1 Small enclosure—e xternal features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Figure 2 Large enclosure—internal features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Figure 3 Typical Configuration . . . . . . . [...]

vi Table 32 Service phone number dial ing results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Table 33 Guidelines for dialing service phone number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Table 34 Automatic / manual control - output points. . . . . . . [...]

Introd uction 1 1.0 I NTRODUCTION The Liebert Universal Monitor’s exte nsi ve capabilities can put it at the heart of your protective net- work. The Universal Monitor employs local alarming and remote paging services to keep personnel on-site and at re mote locations appr ised of the status of equipment. The panel can interface with an y device t[...]

Introd uction 2 1.5 Out side Enclosure Overview The enclosure for the Universal Monitor’ s controller board comes in two sizes: •T h e large enclosure is designed to accommo date the Transformer Module and future compo- nents, in addition to the controll er board. •T h e small enclosure is built to hold the controller board only. Both enclosu[...]

Introd uction 3 1.6 T ypical Configuration Figure 3 shows an example of external devices connecte d to the Universal Monito r’s cont roller board. There may be up to eight digital output, ei ght digital input and f our analog input devices connect ed. The optional Universa l Monitor Expansion Board provi des additional connec tions for eight outp[...]

Introd uction 4 1.7 Controller Board Overview The Universal Monitor’s controller board has connect ors for eight digital inpu ts, f our analog inputs and eight digital outputs, as shown below. The bo ard comes complete with light emitting diodes (LEDs) to display the status of monitored devices, a battery pack for short-term backup, communica- ti[...]

Introd uction 5 K - Digital output loss- of-power jumper One of eight output jumpers. Each di gital output has a jumper to set the fail-safe position of the output poi nt when power fails. The OFF position makes the contact Normally Open (factory defau lt). The ON posi tion makes the co ntact Normally Closed. Note: The jumper position has no effect[...]

Introd uction 6 1.8 Optional Exp ansion Board Overview The Universal Monitor Expansion Bo ard, purchased separately, has connectors for 16 digital input s and eight digital outputs, as shown below. The boar d has light emitting diodes (LEDs) to display the status of monitored output devices, communication s ports for connection to the Univ ersal Mo[...]

Introd uction 7 1.9 LED Indicators The Universal Monitor’s controller board has LED indi cators that show the st atus of inputs, outputs and the common alarm, as well as th e modem and SiteScan Web connections. T able 3 LED indicators summary LED Type LED Color Description EIA422 LEDs 422 TX Green Universal Monitor is transmi tting info rmation o[...]

Introd uction 8 1.10 LED Indicators - Op tional Expansion Board The optional Expansion Board, purchased sep arately, has LED indicators that show the statu s of inputs and outputs. T able 4 LED indicators summary LED Type LED Color Description Power status LED 24VAC Power (D6) Gree n 24VAC power is being supplied to Exp ansion Board EIA485 status L[...]

Introd uction 9 1.1 1 T ypical Sequence Figure 4 shows a typical sequence of how the Universal Monitor functions after detecting a change in a monitored unit or a rea. Many responses depend on configuration settings. This examp le shows what happens when an analog sensor input reaches a high setpoint—assuming the input is defined as alarmable and[...]

Installation - Ma in Board 10 2.0 I NST ALLATION - M AIN B OARD This section provides instru ctions for installing, mou nting and connecting pow er to the Universal Monitor. For information on the optional Expansion Board, see 3.0 - Installation - Optional Expan- sion Board . 2.1 Inst allation Considerations The Universal Monitor must be in stalled[...]

Installation - Ma in Board 11 2.2 Surface-Mounting th e Universal Monitor After dete rmining where to place the unit, check to e nsure that yo u have all the hard ware required to install the panel on the surface of a wall. Obtain the need ed tools and material. Required tools • Electric drill (i f surface is too hard to drive screws wi thout pil[...]

Installation - Ma in Board 12 2.3 Flush-Mounting the Universal Monitor The Universal Monitor may be flus h-mounted according to company practices—either with screws through the sides of the pa nel into wall supports or with hangin g hardware that attaches to the back of the pan el. After dete rmining ho w and where to place the unit, check to ens[...]

Installation - Ma in Board 13 2.4 Connect Power to the Universal Monitor The Universal Monitor requires 24VA C for proper operation. Liebert recomme nds using the optio nal Transformer Module manufactured by Liebert or another UL-approve d Class 2 power unit to obtain proper voltage. If the power unit is not a Class 2 circuit, it must be protected [...]

Installation - Ma in Board 14 2.4.2 T ermination and Mounting - Large Enclosure Input Power Connections To connect el ectrical po wer to the Transformer Module: 1. Ins tall electrical wirin g from utility power to the Tran sformer Module. 2. Use co pper wires only; proper wiring to use fo r po wer is 14/2 AWG coppe r wire with ground. 3. For the TM[...]

Installation - Ma in Board 15 T roubleshooting - T ransformer Module A common problem and possible solution are shown in the table below. For further information or if you have other problems with the unit, consult your local dealer, Liebert repres entative or the Liebert Worldwide Support Group. 2.4.3 Connecting the Battery Pack After connecting A[...]

Installation - Optional Expansion Bo ard 16 3.0 I NST ALLATION - O PTIONAL E XP ANSION B OARD This section provides instructions for installing, mount ing and connecting power to t he optional Expan- sion Board. The Expansion Board enclosure is iden tical to the Universal Mo nitor’s small enclosure . 3.1 Inst allation Considerations The optional [...]

Installation - Optional Expansion Bo ard 17 3.2 Surface-Mounting the Op tional Expansion Board After determining where to place the optional Expansi on Board, check to ensure that you have all the hardware required to install the pa nel on the surface of a wall. Obta in the needed tools and material. Required tools • Electric drill (i f surface i[...]

Installation - Optional Expansion Bo ard 18 3.3 Flush-Mounting the Op tional Exp ansion Board The optional Expansion Board may be fl ush-mounted according to company practices—either with screws through the sides of the panel into wall supp orts or with hanging hardware that attaches to the back of the panel. After dete rmining how and where to p[...]

Installation - Optional Expansion Bo ard 19 3.4 Input Power Connections - Optional Exp ansion Board The optional Expansion Board requ ires 24VAC for proper operatio n. Liebert recommends using the optional Transformer Module manufa ctured by Liebert or another UL -approved Class 2 power unit to obtain proper voltage. If the pow er unit is not a Cla[...]

Wiring and Con nections - Main Boa rd 20 4.0 W IRING AND C ONNECTIONS - M AIN B OARD 4.1 Wiring S pecifications Input and output connecti ons to the Universal Monitor may be made in any order— it is not neces- sary, for example, to make all input connections before making any output connections. Use copper conductors only for all wiring. ! CAUTIO[...]

Wiring and Con nections - Main Boa rd 21 4.2 Connecting Digit al Inpu t s and Digital Output s The digital inputs and digital outp uts are found on the lower right side of the Universal Monitor’s printed wirin g assembly bo ard. There are tw o term inal blocks for the inputs—one green, the other black. There are two terminal blocks fo r the out[...]

Wiring and Con nections - Main Boa rd 22 4.2.3 Setting the Digit al Output Jumpe rs Each digital output has an associ ated jumper to define its operat ion when power is interrupted and there is no battery backup to the board. This puts the Universal Moni tor in a fail-safe mode and ensures proper functionin g when the board has no power or battery [...]

Wiring and Con nections - Main Boa rd 23 4.3.1 Setting the 12VDC/24VDC Analog Power Jumper The analog power jumper sets the common voltage that is applied to all of the analog input connec- tions. The jumper permits the user to modify the voltage supplied to the sensors, according to the power requirements. The factory default position is 24VDC; it[...]

Wiring and Con nections - Main Boa rd 24 4.4 Connecting Common Alarm Output s The common alarm relay, found in the top right corner of the Uni- versal Monitor, permits the user to connect auxiliary notification equipment, such as lights, horn s and sirens, to the Universal Monitor. To determine the proper wire size, see Table 7 - Wiring specificati[...]

Wiring and Co nnections - Optional Ex pansion Bo ard 25 5.0 W IRING AND C ONNECTIONS - O PTIONAL E XP ANSION B OARD 5.1 Wiring S pecifications Input and output connecti ons to the option al Expansion Board may be made in any order—it is not necessary, for example, to make al l input con nections before making any output connecti ons. Use cop- per[...]

Wiring and Co nnections - Optional Ex pansion Bo ard 26 5.2 Connecting Input s and Output s The Universal Monitor’s optional Ex pansion Board permits the addition of 16 input and eight output devices. This section describes ho w to connect devices to the Expa nsion Board’s inputs and outputs. To determine the proper wire size, see Table 9 . 5.2[...]

Wiring and Co nnections - Optional Ex pansion Bo ard 27 5.2.2 Connecting Digit al Output s The eight digital outputs are found at the top of the Expansion Boar d, as show n below. These inputs are numbered 9 through 16. (Note that the digital ou tputs on the main board of the Universal Monitor are numbered 1 - 8.) Each output may be wire d accordin[...]

Wiring and Co nnections - Optional Ex pansion Bo ard 28 5.2.3 Setting the Digit al Output DIP Switches Each digital output on the optional Expansion Board has an associated DIP switch tha t can deter- mine its operation in the eve nt of loss of communica tion with the Universal Monitor or loss of power. When the Universal Monitor calls for an Expan[...]

Wiring and Co nnections - Optional Ex pansion Bo ard 29 5.3 Connect to the Universal Monitor Two steps are required to establish connection be tween the optional Expansion Board and the Uni- versal Monitor. 5.3.1 Connect EIA485 Connectors to Main Board To connect the optional Expansion Board to the Universal Monitor: 1. Turn OFF electrical power to[...]

Overview of Menus 30 6.0 O VERVIEW OF M ENUS There are two ways to access the Universal Monitor: the LCD on the front of the e nclosure and the Service Terminal Interface, which is accessible through any computer using a communications pro- gram. Many viewing and configuration tasks can b e performed through either interface, but some are available[...]

Overview of Menus 31 6.1 Opening Screen Overview The Universal Monitor displa ys the Opening Screen at startup, as shown in Figure 12 . • If any alarms are active, the Current Al arm screen appears. (Pre ssing any key on the LCD keypad will silence the audib le alarm.) • If any analog input sensors ar e connected, the LC D screen will alternate[...]

V iew Status Options 32 7.0 V IEW S TAT U S O PTIONS The View Status menu allows any user to view current ly active alarms, monitoring data stored in the alarm, event and trend logs, the status of all i nputs and outputs, and the four pager numbers. The arrows ↑↓ are used to scroll through the menu. The Enter ↵ key is used to select the me nu[...]

V iew Status Options 33 7.1 View Active Alarms The Active Alarm screen displa ys all alarms tha t are occurring, up to a maximum of 33. A Current Alarm screen appears automatica lly whenever an ala rm occurs—except during setup. This s creen can display only the two most recent active alarms. To view any other active alarms, use the View Active A[...]

V iew Status Options 34 7.2 View Alarm Log The Alarm Log contains up to 99 reco rds of alarms that have occurred. Records are added to this log as alarms occur. To view t he Alarm Log : • From the Main Menu, use the arrows ↑↓ to choose View Status , then press Enter ↵. • From the View Status Menu, use the arrows ↑↓ to choose View Alar[...]

V iew Status Options 35 7.3 View Event Log In addition t o alarms, the Univ ersal Monitor track s other changes in the Event Log to assist users with verifying operat ional and t rouble- shooting problems. Even ts reflect change s in the status of an input that is defined as an event or the change of state of an output (i.e., manually forced ON or [...]

V iew Status Options 36 7.4 View T ren d Log The Universal Monitor takes readings of configure d analog input se n- sors at regular intervals and stores them in four separa te trend logs, one for each sensor. The time interv al is 30 minutes. Each log contains up to 100 records. Follow these steps to select a sensor and view its trend log: 7.4.1 Se[...]

V iew Status Options 37 7.5 View Input S tatus The Input Status option allows you to view the curr ent status o f all inputs: the four analog sensor inputs and the eight digital inputs. If the optional Expansion Board is used, the addi tional 16 digital inputs can also be viewed. To view the Input Status: • From the Main Menu, use the arrows ↑?[...]

V iew Status Options 38 7.6 View Output St atus The Output Status option allows you to view the current status of all eight outputs. If the op tional Expansion Board is used, the additional eight digital outputs can also be viewed. To view t he Output S tatus: • From the Main Menu, use the arrows ↑↓ to choose View Status , then press Enter ?[...]

V iew Status Options 39 7.7 View Pager Numbers The Universal Monitor may be set up to dial pager numbers when an alarm is detected. U p to four pagers may be configured, as d escribed in 9.8 - Setup System - Setup Modem & Pagers . The View Pager Numbers option allo ws you to view the pager numbers and PINs for all configured pa gers. Use the fo[...]

Silence Alarm & Backup Log Files (Service Terminal Interface) 40 8.0 S ILENCE A LARM & B ACKUP L OG F ILES (S ERVICE T ERMINAL I NTERFACE ) This section de scribes two feature s that are availa ble in the Serv ice Terminal Inte rface: • Silence Alarm • Backup Log Files 8.1 Silence Alarm (Service T erminal Interface) The Silence Alarm me[...]

Silence Alarm & Backup Log Files (Service Terminal Interface) 41 8.2 Back Up Log Files (Service T erminal Interface only) The Universal Monitor maint ains th ree types of logs—a larm, event and trend—that may be backed up to a remote computer. This feature is available only through the Service Terminal Interface. To back up any of the al ar[...]

Silence Alarm & Backup Log Files (Service Terminal Interface) 42 5. At the top of the HyperTermina l window, sho wn below, click on Transfer , then on Receive File . 6. In the Receive File windo w, as shown above: • In the Place Receiv ed File in the Foll owing Folder box, enter the na me and locatio n of the folder where the configuration fi[...]

System and Control Options 43 9.0 S YSTEM AND C ONTROL O PTIONS The System and Control menu allows you to config ure the Universal Monitor— setting up inputs and outputs and an input/output matrix to trigger ac tions, the modem and pagers, and system features such as date and time. This menu also provides a ve hicle for ma nually changing t he st[...]

System and Control Options 44 Figure 14 shows the main options availabl e from the System & Control menu. Figure 14 Me nu overview - System and Contro l menu Opening Screen UNIVERSAL MONITOR DD-MON-YY HR:MM:SS VX.XXX.X PRESS ↵ =STATUS/SETUP Main Menu VIEW STATUS > SYSTEM AND CONTROL ↑↓ =NEXT ↵ =SELECT Login Screen LOGIN AAAA ↑↓ =[...]

System and Control Options 45 9.2 Setup System - Overview The Setup System screen displays seven options that al low you to configure input and output devices and their relation ships, the common alarm, the modem, pagers to be dialed when alarms occur, and a variety of system details, such as login password and system date and time: • Setup Input[...]

System and Control Options 46 9.3.1 Change Label (Name of Input) Each input has a d efault label ( Input_01, Input_02, etc.) that you may change to a more descri ptive name for ease in recognizin g alarms and events associated with the input. Th e label may consist of up to eight characters (see Table 20 for valid characters). • From the Setup In[...]

System and Control Options 47 9.3.4 Set Up Alarmable Input s in Latched or Unlatched Mode Alarmable input points may be set up in Latched mode (Y), which requires the user to cl ear the Universal Monitor al arms after an al arm has occurred, or Unlatched mode (N), in which alarms will automati- cally clear after a return-to-normal state. The defaul[...]

System and Control Options 48 9.4 Setup System - Setup Common Alarm The audible al arm sounds afte r the Universal M onitor detects an alarm condition in any input th at has been defined as a larmable, including digita l and analog sensor inputs. O nce the alarm i s silenced, there are two options: • By default, the common alarm remains ener gize[...]

System and Control Options 49 9.5 Setup System - Setup Sensor The Universal Monitor has four analog sensor input points that may be configured indi vidually. The panel monitors connected equipment for any 4-20 mA input—for example, temperature and humidity. To configure a sensor: Log In and Choose Setup System • From the Main Menu, use the arro[...]

System and Control Options 50 9.5.1 Identify the Sensor as Connected To make use of an analog sensor, yo u must specify it as Connected (Y ). By default, analog sensor s are Not conne cted (N). • From the Setup Sensor Menu, choose Connected , as shown at right, and press Enter ↵ . • To change this feature, use the arrows ↑↓ to choose Y (Y[...]

System and Control Options 51 9.5.4 Change 4 mA V alue For the 4 mA value, enter the smalle st v alue for the range of the sen- sor—for example, 50°F for a tempe rature sensor with a range of 50°F to 90°F. The default value for each sensor is -999.9. Values that can be entered range from -999.9 to +999.9. To enter a new value: • From the Set[...]

System and Control Options 52 9.5.7 Define Sensor as Alarmable or Event Each sensor may be defined as Alarmable (AL) or as an Event (EV). • For a sensor defined as alarmable, the following alarm reactions occur when the high-setpoint thresh old is crossed: the LCD flashes, the audible horn sounds, configured pa ger numbers will be not ified and a[...]

System and Control Options 53 9.5.9 Change Low Setpoint The Low Setpoint value is typicall y above the 4 mA value for the sen - sor. For example, if the 4 mA value is 50°F, the Low Setpoint might be 60°F. When the sensor crosses below th is value, an alarm or event will occur, depending on the sensor configuration. The default Low Setpoint for ea[...]

System and Control Options 54 9.5.1 1 Set Up Delay Time Each sensor may be set up with a specified time delay between the triggering of a high or low se tp oint—a monitored sensor crosses the high or low setpoint threshold—an d any response by the Universal Monitor. This feature can prevent transient conditions from prompting unnecessary respon[...]

System and Control Options 55 9.6 Setup System - Setup I/O Matrix The Setup I/O Matrix menu allows you to configure the Universal Moni tor’s digital and analog in puts to trigger various acti ons in any or all of the 16 outputs—eight on the main board and another eight if the optional Expansion Board is used . Each output can be set up to respo[...]

System and Control Options 56 Map Input to Exp ansion Board Output • From the Select Outputs menu, select Map to Exp Board if you want to map the selected input to an output on the optional Expan- sion Board. These outputs are identified as Outputs 9-16. • On the Output Map screen, you ma y map the selected input to any of the eight outputs (9-[...]

System and Control Options 57 9.6.2 Set Up Mapping for an Analog Sensor Input • Use the arrows ↑↓ to choose Map Sensor To Outpt from the Map Input/Sensor Menu, and press Enter ↵ . • From the Select Sensor Menu, choo se the input you want—for example, Sensor_1 High Stpt —and press Enter ↵ . Map Sensor to Main Bo ard Output • From t[...]

System and Control Options 58 9.7 Setup System - Setup Output The Universal Monitor has eight outp uts that may be configured indi- vidually. If the optional Expansion Board is used, its additional eig ht digital outputs may be renamed. Th e outputs may have a wide varie ty of Liebert or other manufacturers’ equipment connected for configured res[...]

System and Control Options 59 9.7.3 Set Exp ansion Board Outpu t by DIP Switch If you choose Change State from the Setup Output Menu for an Expansion Boa rd output (O UTPUT09-16), the screen displa ys a mes- sage that the state must be set by DIP switch, as shown at right. Each digital output on the optional Expansion Board has an associated DIP sw[...]

System and Control Options 60 9.8 Setup System - Se tup Modem & Pagers To use the modem and pager features, be sure to co nnect the phone line connector to a telephone wall jack using an RJ11 cord, as described in 4.6.2 - Phone Line Connector . 9.8.1 Modem Setup - Initialization S tring The Universal Monitor has an on-boa rd modem that of fers [...]

System and Control Options 61 Select Modem Setup 4. From the Setup Sy stem Menu, shown at right, use the arrows ↑↓ to choose Setup Modem&Pagers and press Enter ↵ . 5. Use the arrow s ↑↓ to choose Setup Mode m from the Pagers & Modem Menu and press Enter ↵ . 6. Th e Setup Modem Men u displays the i nitialization stri ng (Init Str[...]

System and Control Options 62 9.8.2 Modem Setup - Additional Features (Service T erminal Interface only) The Service Terminal Interface offe rs four additional opti ons for the modem that are not available through the LCD interface: • Enter Universal Monitor phone number • Enable modem diag nostic messages • Change modem dial prefi x • Chan[...]

System and Control Options 63 Enable Modem Diagnost ic Messages Enabling modem d iagnostics wil l provide the following addi tional informati on about the modem to the computer using the Service Terminal Interface: • At the Enable Modem Diagnost ic Messages prompt, ente r Y (Yes - enable) or N (No - disable). The current setting appears i n brack[...]

System and Control Options 64 9.8.3 Pager Setup - Pager Number and PIN The Universal Monitor may be config ured to dial numeric or alphanumeric pagers when an alarm is detected. You may enter up to four pager numbers—all configured pagers will be dialed each time an alarm occurs. For each configured pager, you mu st enter the pager numbe r to be [...]

System and Control Options 65 Enter a Pager Number • From the Setup Pager Menu, choose Setup Pager Number for the selected pager— Setup Pager 1 Number in the example at right—and press Enter ↵ . • See Table 30 for guidelines on enteri ng the pager number, which may consist of up to 40 charac ters. To enter the pager number: • Use the ar[...]

System and Control Options 66 9.8.4 Pager Setup - Communications Ch eck (Service T erminal Interface only) The Service Terminal Interface offe rs two additional op tions for pager setup, which are not available through the LCD interface: • Enable communications check • Enter time to perform communications check To access these options: • Conn[...]

System and Control Options 67 Enable Communications Check Enabling this function permits a daily communica tions test between the Universal Monitor and the selected pager. Once each day the Universal Moni tor dials the pager at a specified time and sends this message: “UNIVERSAL MONITOR COMM CHECK.” (T he time of the test is s p ecified at the [...]

System and Control Options 68 9.9 Setup System - Setup System Info The Setup System Info options allow users to: • Change Passw ord —used for access to system setup functions • Change Date & Time/Automatic Dayl ight Saving Time —used to set the Universal Monitor’s date and time and to enab le automatic time change for Daylig ht Saving[...]

System and Control Options 69 9.9.1 Change Password A password is required to access th e Universal Monitor’s sy stem and control options, as described in 9.1 - Login . The password consists of four characters (see Table 20 for valid characters). The default pass- word is AAAA. Change the Password To change the password: • From the Setup System[...]

System and Control Options 70 9.9.3 Setup Site ID You may enter a Site ID to identify the Univ ersal Monitor’s locatio n, using a name that may consist of up to 40 characters (see Table 20 for valid characters). The Site ID will app ear with each alarm. To enter or change the Site ID: • From the Setup System Info Menu, use the arrows ↑↓ to [...]

System and Control Options 71 9.9.5 Backup and Upload Configuration File (Service T erminal Interface only) This operation may be performed only through the Se rvice Terminal Interface. It permits the user to make a copy of the Universal Monitor’s config uration settings and save it as a file on the com puter connected through the RS232 port. Sho[...]

System and Control Options 72 Back Up the Conf iguration File 8. At the prompt to Initiate a Ba ckup of Configuration File, enter Y (Yes - begin) or N (No - cancel). The current setting appears in brackets—[ N] in the following example. 9. At the top of the HyperTermina l window, sho wn below, click on Transfer , then on Receive File . 10. In the[...]

System and Control Options 73 Upload the Configuration File 13. At the prompt to Initiate an Upload of Configura tion File, enter Y (Yes - begin) or N (No - cancel). The current setting appears in brackets—[ N] in the following example. 14. At the top of the HyperTermina l window, shown b elow, click on Transfer , then on Send File . 15. In the S[...]

System and Control Options 74 9.9.6 Setup Serv Ph Num - Enter Phone Nu mber The Service Phone Number (Serv Ph Num) is used fo r remote monitoring by Liebert Global Services. The number is designed to allow re mote monitoring servic es to connect to the Univ ersal Monitor. All alarms will be sent to this number. When an alar m occ urs, this number i[...]

System and Control Options 75 9.9.7 Setup Serv Ph Num - Communication s Check (Service T erminal Interface only) The Service Terminal Interface offers two additiona l options for setting up the Service Phone Number (Serv Ph Num) that are not available through the LCD interface: • Enable communications check • Enter time to perform communication[...]

System and Control Options 76 9.9.8 Factory Default s At any time, you may restore all defa ult values for settings in the Un i- versal Monitor as it was shipped. The password is the sole exceptio n when reverting to the factory default settings. The pas sword can be reset to the factory default of AAAA only through the DIP switches. Fo r details, [...]

System and Control Options 77 2. The firmware update is a two-step process—this step describes how to upload the file prog###.s19 (where ### is a number—for example, prog11 8.s19) to the Uni versal Monitor: a. At the top of the HyperTermin a l window, shown below, click on Transfer , then on Send File . b. In the Send File window, as sho wn abo[...]

System and Control Options 78 9.9.10 Initiate Remote Alarm T est (Service T erminal Interface only) The service phone number is used for remote monito ring by Liebert Global Services. The Service Ter- minal Interface may be used to test communicati ons between the Universal Monitor and the service modem. This te st will send a “DIAL OUT TEST PASS[...]

System and Control Options 79 9.10 Setup Exp Board - Op tional Expansion Board By default, the optional Expansion Board is config ured as Not connected (N ). After connecting power to the board and connecting it to the Universal Monitor, you must specify the Expansion Board as Connected (Y), as described in this section. To change the Expansion Boa[...]

System and Control Options 80 9.1 1 Manual Output Ctrl The Manual Output Ctrl feature allows you to manua lly change the state of any digital output to ON or OFF, overriding automatic cont rol by the Universal M onitor (the default setting for all ou tputs). This menu also allows you to rele ase the manual override, returning any output to automati[...]

System and Control Options 81 9.12 Clear Alarms & Logs The Clear Alarms & Logs menu allows you to clea r active alarms or delete all records from any of th e Universal Monitor’s three logs: alarm, event and trend log s. To clear alarms or logs: Log In and Choose Clear Alar ms & Logs • From the Main Menu, use the arrows ↑↓ to cho[...]

System and Control Options 82 9.12.3 Clear the Event Log The event log contains up to 99 records of ev ents detected by the Uni- versal Monitor. You may want to clea r the log after backing up the file or simply to free up space. To delete all records from the event log: • From the Clear Alarms / Logs Menu, use the arrows ↑↓ to choose Clear E[...]

Specifications 83 10.0 S PECIFICATIONS 10.1 Universal Moni tor Specifications Power Requirements Small Enclosure L arge Enclosure NOTE UMS02400 1 15V AC UML1 1500 230V AC UML23000 If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. 24VAC ±10% of nominal; 50/60 Hz, 1.3A, [...]

Specifications 84 10.2 Optional Expa nsion Board Specifications Power Requirements UMEXP NOTE If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. 24VAC ±10% of nominal; 50/60 Hz, 0.6A, 15VA Class 2 Dimensions W x D x H, in. (mm) 14-1/4 x 2-3/4 x 12 (361.95 x 69.85 x 304 [...]

Service T erminal Interface 85 A PPENDIX A- S ERVICE T ERMINAL I NTER FACE The Service Terminal Interface allows access to al l functions of the Universa l Monitor, including some that are not possible through the LCD interface. This interfa ce is accessible through any com- puter using a communications program such as Microsoft ® Windows ® Hyper[...]

Connecting to the Service Terminal Interface 86 A.2 C ONNECTING TO THE S ERVICE T ERMINAL I NTERFACE This section describes how to set up and connect to the Service Terminal Interface. A.2.1 Connection Methods There are two ways to access th e Service Terminal Interface: • Direct —Use a null modem cable to connect a comput er’s COM1 port to t[...]

Connecting to the Service Terminal Interface 87 A.2.2 Create a Connection Before connecting to the Service Terminal Interfac e, you must create a connectio n and specify the method to be used for connection, as described in th e followi ng steps. 1. Start the HyperTerminal progra m—to do this, click on the Start button, then on Programs , then Ac[...]

Connecting to the Service Terminal Interface 88 A.2.3 Set Up the COM1 Port - Direct Connection Only The following steps apply only to setting up a dire ct connection to the Servic e Terminal Interface via the Universal Monitor’s RS232 port. If you are setting up a remote connection via modem, skip to Step 8 (next section). COM1 Port Setup 6. In t[...]

Connecting to the Service Terminal Interface 89 A.2.4 Set Up the Connection’ s Properties The following steps are needed for both direct and remote connection to the Universal Monitor. Properties Setup 8. Open the Properties wi ndow by clicking on File , then on Properties , as shown below left. 9. In the Propertie s window, above right, click on[...]

Connecting to the Service Terminal Interface 90 A.2.5 Connect to the Serv ice T erminal Interface After creating and setting up a connection, use a communic ations program such as HyperTerminal to access the Universal Monitor’s Service Terminal Interface. 1. Verify communications connectio ns between the remote comput er and the Universal Monitor[...]

Overview of Menus 91 A.3 O VERVIEW OF M ENUS The Main Menu offers choices for vi ewing the status of the Universa l Monitor, silencing the audible alarm and backin g up the unit’s log files. It also allows access to the Sy stem and Control features, which require a password. The following shows where to find examples of the Main Menu screens: A.3[...]

Vi e w St a t u s M e n u s 92 A.4 V IEW S TAT U S M ENUS The View Status menu allows any user to view current ly active alarms, monitoring data stored in the alarm, event and trend logs, the status of all i nputs and outputs, and the four pager numbers. Main Menu After connecting to the Service Terminal Interface, the Main Menu appears, as shown b[...]

Vi e w St a t u s M e n u s 93 A.4.1 V iew Active Alarms For details on this feature, see 7.1 - View Active Alarms . V iew Active Alarms ACTIVE ALARMS Input points/ hardware presently in an alarm sta te SENSOR_1 10 1.1 DEG HIGH SETPOINT ALARM SENSOR_2 --- --- DEG SENSOR PROBLEM INPUT_07 ALA RM CONTACT OPEN BATTERY CHECK BATTERY <ENTER>=MORE &[...]

Vi e w St a t u s M e n u s 94 A.4.2 V iew Alarm Log For details on this feature, see 7.2 - View Alar m Log . V iew Alarm Log ALARM LOG Alarm history SENSOR_2 8 0.0 DEG HIGH SETPOINT ALARM 29-AUG-02 0 9:29:10 MODEM INTERNAL FAUL T 29-AUG-02 0 9:20:10 INPUT_08 ALA RM CONTACT CLOSE D 29-AUG-02 0 9:19:10 SENSOR_2 7 9.0 DEG RETURN TO NORMAL 28-AUG-02 1[...]

Vi e w St a t u s M e n u s 95 A.4.3 V iew Event Log For details on this feature, see 7.3 - View Event Log . Vi e w E v e n t L o g EVENT LOG Event history PAGER UNSUCCESSFUL PAG E 07-MAY-02 1 0:29:10 OUTPUT01 MAN ON CONTACT CLOSE D 07-MAY-02 0 9:20:10 OUTPUT08 ON CONTACT OPEN 07-MAY-02 0 8:20:10 OUTPUT08 MAN OFF CONTACT CLOSE D 07-MAY-02 0 6:20:10[...]

Vi e w St a t u s M e n u s 96 A.4.4 V iew T rend Log For details on this feature, see 7.4 - View Trend Log . V iew Trend Log TREND LOG Trend history for each sensor Select sensor for trend you want to v iew. 1=SENSOR_1 2=SENSOR_2 3=SENSOR_3 4=SENSOR_4 5=RETURN TO MA IN MENU SELECT A NUMBER:1 TREND LOG Trend history SENSOR_1 7 5.4 DEG NORMAL 28-AUG[...]

Vi e w St a t u s M e n u s 97 A.4.5 V iew Input S t atus For details on this feature, see 7.5 - View Input Status . V iew Input & Sen sor Sta tus INPUT & SENSOR STATUS Sensor values & discre te inputs status INPUT STATUS /VALUE SENSOR_1 8 0.0 DEG SENSOR_2 --- --- DEG SENSOR_3 8 0.0 DEG SENSOR_4 7 9.5 RH INPUT_01 NOR MAL INPUT_02 ALA RM[...]

Vi e w St a t u s M e n u s 98 A.4.6 V iew Output S t atus For details on this feature, see 7.6 - View Output Status . Vi e w O u t p u t S t a t u s OUTPUT STATUS Discrete outp uts status OUTPUT STAT US OUTPUT01 ON OUTPUT02 OFF OUTPUT03 ON OUTPUT04 MAN ON OUTPUT05 ON OUTPUT06 OFF OUTPUT07 MAN OFF OUTPUT08 ON OUTPUT09 ON OUTPUT10 OFF OUTPUT11 ON OU[...]

Vi e w St a t u s M e n u s 99 A.4.7 V iew Pager Numbers For details on this feature, see 7.7 - View Pager Number s . V iew Pager Numbers PAGER & PIN NU MBERS Numbers to dial for an alarm PAGER 1 NUMBE R A1,8005551212 PAGER 1 PIN 0123456789101 1121314 PAGER 2 NUMBE R A9W1,80055512 12 PAGER 2 PIN 0123456789101 1121314 <ENTER>=MORE <ES C[...]

Silence Alarm & Back Up Log Files (Service Terminal Interface only) 100 A.5 S ILENCE A LARM & B ACK U P L OG F ILES (S ERVICE T ERMINAL I NTERFACE ONLY ) This section presents two option s from the Main Menu that are av ailable via the Service Termina l Interface only. Main Menu After connecting to the Service Terminal Interface, the Main M[...]

Silence Alarm & Back Up Log Files (Service Terminal Interface only) 101 A.5.2 Back Up Log File s (Service T erminal Interface only) For details on this feature, see 8.2 - Back Up Log Files (Service Te rminal Interface only) . Back Up Alarm Log File Backup Log Files - Alarm Log File BACKUP LOG FILE S Backup alarm, e vent and trend log files 1=BA[...]

Silence Alarm & Back Up Log Files (Service Terminal Interface only) 102 Back Up Event Log File Backup Log Files - Event Log File BACKUP LOG FILE S Backup alarm, e vent and trend log files 1=BACKUP ALARM LOG FILE 2=BACKUP EVENT LOG FILE 3=BACKUP TREND LOG FILE-SENSO R_1 4=BACKUP TREND LOG FILE-SENSO R_2 5=BACKUP TREND LOG FILE-SENSO R_3 6=BACKUP[...]

Silence Alarm & Back Up Log Files (Service Terminal Interface only) 103 Back Up T rend Log Files Backup Log Files - T rend Log Files BACKUP LOG FILE S Backup alarm, e vent and trend log files 1=BACKUP ALARM LOG FILE 2=BACKUP EVENT LOG FILE 3=BACKUP TREND LOG FILE-SENSO R_1 4=BACKUP TREND LOG FILE-SENSO R_2 5=BACKUP TREND LOG FILE-SENSO R_3 6=BA[...]

Setup Menu 104 A.6 S ETUP M ENU The Setup menu allows the user to configure the Universal Monitor—setting up inputs and outputs and an input/output matrix to tr igger actions, the mod em and pagers, a nd system featur es such as date and time. This menu also provides a vehicle fo r manually changing t he stat e of an output to ON or OFF, clearing[...]

Setup Menu 105 Setup Menu This section presents Service Terminal In terface screens for ea ch of the following: * Setup System Information features are: • Change Password • Change Date & Ti me/Automatic Daylig ht Saving Time • Setup Site ID • Connect Battery • Backup and Upload Configuration File (Service Terminal Interface only) • [...]

Setup Menu 106 A.6.1 Setup Input For details on this feature, see 9.3 - Setup System - Setup Input . Setup Input - Main Board Outputs SETUP INPUT Setup for disc rete input points Select input t o edit INPUT DEFINITION 1=INPUT_01 NO-EV-NL -00:01 2=INPUT_02 NO-AL-L -00 :01 3=INPUT_03 NC-EV-NL -00:01 4=INPUT_04 NO-AL-L -00 :01 5=INPUT_05 NC-AL-L -00 :[...]

Setup Menu 107 Setup Input - Expan sion Board Inputs SETUP INPUT Setup for disc rete input points Select input t o edit INPUT DEFINITION 1=INPUT_01 NO-EV-NL -00:01 2=INPUT_02 NO-AL-L -00 :01 3=INPUT_03 NC-EV-NL -00:01 4=INPUT_04 NO-AL-L -00 :01 5=INPUT_05 NC-AL-L -00 :01 6=INPUT_06 NO-EV-NL -00:01 7=INPUT_07 NO-AL-L -00 :01 8=INPUT_08 NC-EV-NL -00:[...]

Setup Menu 108 A.6.2 Setup Common Alarm For details on this feature, see 9.4 - Setup System - Setup Common Alarm . Setup Common Alarm SETUP COMMON A LARM Select if the common alarm relay co ntact is to reset wi th silence alarm CURRENT SETTING 1=SETUP COMMON ALARM N 2=RETURN TO SE TUP MENU 3=RETURN TO MA IN MENU SELECT A NUMBER:1 >RESET COMMON A[...]

Setup Menu 109 A.6.3 Setup Se nsor For details on this feature, see 9.5 - Setup System - Setup Sensor . Setup Sensor SETUP SENSOR Setup for ana log input points Select sensor to edit SENSOR VA LUE 1=SENSOR_1 80.0 DEG 2=SENSOR_2 -- ---- DEG 3=SENSOR_3 80.0 DEG 4=SENSOR_4 79.5 RH 5=RETURN TO SE TUP MENU 6=RETURN TO MA IN MENU SELECT A NUMBER:1 >IS[...]

Setup Menu 110 >[ >COMMAND SUCCE SSFUL >CHANGE OFFSET VALUE . >[000.0] >[ >COMMAND SUCCE SSFUL >IS SENSOR AN ALARM(AL) OR EV ENT(EV)? >[AL] >[ >COMMAND SUCCE SSFUL >IS SENSOR ALARM LATCHE D-YES(Y) OR NO(N)? >[Y] >[ >COMMAND SUCCE SSFUL >CHANGE LOW SETPOINT . >[-0015.0] >[ >COMMAND SUCCE SSFUL &g[...]

Setup Menu 111 A.6.4 Setup I/O Matrix For details on this feature, see 9.6 - Setup System - Setup I/O Matrix . Setup I-O Matrix - Map Input to Ou tput - Main Board In puts SETUP I/O MATRIX Program inputs & sensors to control ou tputs Select to map inputs or senso rs 1=MAP INPUT TO OUTPUT 2=MAP SENSOR T O OUTPUT 3=RETURN TO SE TUP MENU 4=RETURN [...]

Setup Menu 112 >[ >COMMAND SUCCE SSFUL >MAP INPUT_01 TO OUTPUT 06-YES(Y) OR NO(N)? >[N] >[ >COMMAND SUCCE SSFUL >MAP INPUT_01 TO OUTPUT 07-YES(Y) OR NO(N)? >[N] >[ >COMMAND SUCCE SSFUL >MAP INPUT_01 TO OUTPUT 08-YES(Y) OR NO(N)? >[N] >[ >COMMAND SUCCE SSFUL >MAP INPUT_01 TO OUTPUT 09-YES(Y) OR NO(N)? >[...]

Setup Menu 113 Setup I-O Matrix - Map Input to Ou tput - Expansion Board Input s SETUP I/O MATRIX Program inputs & sensors to control ou tputs Select to map inputs or senso rs 1=MAP INPUT TO OUTPUT 2=MAP SENSOR T O OUTPUT 3=RETURN TO SE TUP MENU 4=RETURN TO MA IN MENU SELECT A NUMBER:1 MAP INPUT TO OUTPUT Program input to control ou tput(s) Sel[...]

Setup Menu 114 >MAP INPUT_09 TO OUTPUT 01-YES(Y) OR NO(N)? >[Y] >[ >COMMAND SUCCE SSFUL >MAP INPUT_09 TO OUTPUT 02-YES(Y) OR NO(N)? >[N] >[ >COMMAND SUCCE SSFUL >MAP INPUT_09 TO OUTPUT 03-YES(Y) OR NO(N)? >[N] >[ >COMMAND SUCCE SSFUL >MAP INPUT_09 TO OUTPUT 04-YES(Y) OR NO(N)? >[N] >[ >COMMAND SUCCE S[...]

Setup Menu 115 Setup I-O Matrix - Map Sensor to Output SETUP I/O MATRIX Program inputs & sensors to control ou tputs Select to map inputs or senso rs 1=MAP INPUT TO OUTPUT 2=MAP SENSOR T O OUTPUT 3=RETURN TO SE TUP MENU 4=RETURN TO MA IN MENU SELECT A NUMBER:2 MAP SENSOR TO OUTPUT Program sensor to control ou tput(s) Select sensor to map SENSOR[...]

Setup Menu 116 >[ >COMMAND SUCCE SSFUL >MAP SENSOR_1 HIGH STPT TO OU TPUT06-YES(Y ) OR NO(N)? >[N] >[ >COMMAND SUCCE SSFUL >MAP SENSOR_1 HIGH STPT TO OU TPUT07-YES(Y ) OR NO(N)? >[N] >[ >COMMAND SUCCE SSFUL >MAP SENSOR_1 HIGH STPT TO OU TPUT08-YES(Y ) OR NO(N)? >[N] >[ >COMMAND SUCCE SSFUL >MAP SENSOR_1 [...]

Setup Menu 117 A.6.5 Setup Output For details on this feature, see 9.7 - Setup System - Setup Output . Setup Output - Main Board Outputs SETUP OUTPUT Setup for disc rete output points Select output to edit OUTPUT DEFINITION 1=OUTPUT01 NO 2=OUTPUT02 NC 3=OUTPUT03 NO ************** **** 4=OUTPUT04 NC NO=NORMALLY OPENED 5=OUTPUT05 NO NC=NORMALLY CLOSE[...]

Setup Menu 118 Setup Output - Expansion Boar d Outputs SETUP OUTPUT Setup for disc rete output points Select output to edit OUTPUT DEFINITION 1=OUTPUT01 NO 2=OUTPUT02 NC 3=OUTPUT03 NO ************** **** 4=OUTPUT04 NC NO=NORMALLY OPENED 5=OUTPUT05 NO NC=NORMALLY CLOSED 6=OUTPUT06 NC ************** **** 7=OUTPUT07 NO 8=OUTPUT08 NC 9=EXPANSION BO ARD[...]

Setup Menu 119 A.6.6 Setup Modem & Pagers For details on this topic, see 9.8 - Setup System - Setup Modem & Pagers . Pager Setup For details on this feature, see 9.8.3 - Pager Setup - Pager Number and PIN and 9.8.4 - Pager Setup - Communications Check (Ser vice Terminal Interface on ly) . Setup Modem & Pagers - Pager Setup SETUP MODEM&a[...]

Setup Menu 120 Modem Setup For details on this feature, see 9.8.1 - Modem Setup - Initialization String and 9.8.2 - Modem Setup - Additional Featu res (Service Termi nal Interface only) . Setup Modem & Pagers - Modem Setup SETUP MODEM&PAGERS Input pager a nd modem informa tion Select pager or modem CURRENT NUMBE R ************* ****** 1=PAG[...]

Setup Menu 121 A.6.7 Setup System In fo This section presents Service Terminal Interface s creens for choices 1 throug h 9 in the Setup System Information menu show n below. For details on this topic, see 9.9 - Setup System - Setup System Info . Change Password For details on this feature, see 9.9.1 - Change Password . Setup System Info SETUP SYSTE[...]

Setup Menu 122 Change Date & Tim e/Automatic Daylight Saving T ime For details on this feature, see 9.9.2 - Change Date & Time/Automatic Da ylight Saving Time . Setup Site ID For details on this feature, see 9.9.3 - Setup Site ID . Change Date & Time CHANGE DATE & T IME CURRENT DATE & T IME DST 1=CHANGE DATE & TIME 28-AUG-02[...]

Setup Menu 123 Connect Battery For details on this feature, see 9.9.4 - Connect Battery . Backup and Upload Configuration File (Servic e T erminal Interface only) For details on this feature, see 9.9.5 - Backup and Upload Config uration File (Service Termi- nal Interface only) . Connect Battery CONNECT BATTERY CURRENT SETTING 1=CONNECT BATT ERY Y 2[...]

Setup Menu 124 Setup Service Phone Number For details on this feature, see 9.9.6 - Setup Serv Ph Num - Enter Phone Number and 9.9.7 - Setup Serv Ph Num - Communications Ch eck (Service Terminal Interface onl y) . Backup & Upload Configuration File - Upload BACKUP AND UPLO AD CONFIGURATIO N FILE Backup from panel saves pan el configurations Uplo[...]

Setup Menu 125 Factory Default s For details on this feature, see 9.9.8 - Factory Defaults . Firmware Up date (Service T erminal Interface only) For details on this feature, see 9.9.9 - Perform Firmware Update (Service Terminal Interface only) . Factory Defaults RESTORE FACTO RY DEFAULTS This command re stores all pane l information to factor y set[...]

Setup Menu 126 Initiate Remote Alarm T est (Service T erminal Interface only) For details on this feature, see 9.9.10 - Initiate Remote Alarm Test ( Service Terminal I nterface only) . Initiate Remote Alarm T est INITIATE REMOTE ALA RM TEST This command si mulates an alar m to test alarm n otification set up for the service phone number 1=INITIATE [...]

Setup Menu 127 A.6.8 Connect Exp ansion Board For details on this feature, see 9.10 - Setup Exp Board - Optional Expansion Board . Connect Expansio n Board CONNECT EXPANSION BOARD CURRENT SETTING 1=CONNECT EXPA NSION BOARD N 2=RETURN TO SE TUP MENU 3=RETURN TO MA IN MENU SELECT A NUMBER:1 >IS THE EXPANS ION BOARD CONNE CTED-YES(Y) OR NO(N)? >[...]

Setup Menu 128 A.6.9 Override Output For details on this feature, see 9.11 - Manual Output Ctrl . Override Output - M ain Board Outpu ts OVERRIDE OUTP UT Manually overr ide an output poi nt Select output to overri de OUTPUT CON TROL 1=OUTPUT01 AUTO 2=OUTPUT02 AUTO *** *************** **************** ********** 3=OUTPUT03 AUTO AUT O =CONTROL BY PAN[...]

Setup Menu 129 Override Output - Ex pansion Board Outpu ts OVERRIDE OUTP UT Manually overr ide an output poi nt Select output to overri de OUTPUT CON TROL 1=OUTPUT01 AUTO 2=OUTPUT02 AUTO 3=OUTPUT03 AUTO ********* **************** *************** **** 4=OUTPUT04 AUTO AUTO =CONT ROL BY PANEL 5=OUTPUT05 AUTO MAN ON =OVERRID E IN ON POSITION BY OPERATO[...]

Setup Menu 130 A.6.10 Clear Alarms & Logs For details on this topic, see 9.12 - Clea r Alarms & Logs . Clear Active Alarms For details on this feature, see 9.12.1 - Clear Activ e Alarms . Clear the Alarm Log For details on this feature, see 9.12.2 - Clear the Alarm Log . Clear Alarms & Logs - Clear Active Alarms CLEAR ALARMS& LOGS C[...]

Setup Menu 131 Clear the Event Log For details on this feature, see 9.12.3 - Clear the Event Log . Clear the T rend Logs For details on this feature, see 9.12.4 - Clear the Trend Logs . Clear Alarms & Logs - Clear the Event Log CLEAR ALARMS& LOGS Clear active alarms or log record s Select the lo g to clear 1=CLEAR ACTIVE ALARM S 2=CLEAR ALA[...]

Default Settings Quic k Referenc e Guide 132 A PPENDIX B- D EFAULT S ETTINGS Q UICK R EFERENCE G UIDE This appendi x provides a quick reference to def ault settings for th e Universal Mon itor and the optional Expansion Board. These setti ngs also appear t hroughout the manual. T able 37 Universal Monitor - de fault settings fo r input s and output[...]

Default Settings Quic k Referenc e Guide 133 T able 38 Universal Monitor - ot her default sett ings JUMPER SETTINGS Feature Default Other Options Digital output loss-of-power jumpers OFF - Normally Open ON - Normally Closed Note: Jumper position has no effect when the Univer sal Monitor has power. 12VDC/24VDC analog input ju mper 24VDC Acceptabl e [...]

Default Settings Quic k Referenc e Guide 134 T able 39 Exp ansion Board - defau lt settings for input s and output s DEFAULT SETTINGS - DIGITAL INPUTS (FROM TABLE 21) Feature Default Other Options LABEL INPUT_09 - INPU T_24 Any name (up to eight characters) NORM OPEN/CLOSE NO (Normally open) NC (Normally closed) ALARM/EVENT AL (Alarmable) EV (Event[...]

[...]

The Comp any Behind the Product s With over a million installations around th e globe, Liebert is the world leader in computer protection systems. Since its founding in 1965, Liebert has developed a complete range of support and protection systems fo r sensitive electronics: • Env ironmental sys tems—close-control air conditioning from 1 to 60 [...]