Lucent Technologies Host-Based Controller Modem AT Bedienungsanleitung

Zur Seite of 87

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Lucent Technologies Host-Based Controller Modem AT an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Lucent Technologies Host-Based Controller Modem AT, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Lucent Technologies Host-Based Controller Modem AT die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Lucent Technologies Host-Based Controller Modem AT. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Lucent Technologies Host-Based Controller Modem AT sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Lucent Technologies Host-Based Controller Modem AT
- Den Namen des Produzenten und das Produktionsjahr des Geräts Lucent Technologies Host-Based Controller Modem AT
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Lucent Technologies Host-Based Controller Modem AT
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Lucent Technologies Host-Based Controller Modem AT zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Lucent Technologies Host-Based Controller Modem AT und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Lucent Technologies finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Lucent Technologies Host-Based Controller Modem AT zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Lucent Technologies Host-Based Controller Modem AT, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Lucent Technologies Host-Based Controller Modem AT widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    Data Addendum June 15, 1998 Version 1.1 Host-Based Controller Modem AT Command Set Contents Page AT Command Summary ........................................ 2 AT Commands Reference ..................................... 6 Test and Debug AT Commands .......................... 24 AT Commands Reference S-Registers ............... 29 AT FAX Command Set [...]

  • Seite 2

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 2 Version 1.0 Lucent Technologies Inc. AT Command Summary The following tables summarize the commands implemented by the modem. Commands may be executed when the modem is in COMMAND mode. COMMAND mode is entered upon under one of the following conditions: ✟ After power up ✟ [...]

  • Seite 3

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Co mmand Set AT Command Summary (continued) Version 1.0 Lucent Technologies Inc. 3 Table 2 . AT Testing and Debugging Command Set Summary Command Description Command Description &&C Write to/read from host interface %T94 Test external DSP RAM &&L Line-to-line loopback %T124 [...]

  • Seite 4

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Summary (continued) Lucent Technologies Inc. Version 1.0 4 Table 4 . The Result Code Summary Result Code Numeric Description OK 0 Command executed CONNECT 1 Modem connected to line RING 2 A ring signal has been detected NO CARRIER 3 Modem lost carrier signal, or does [...]

  • Seite 5

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Co mmand Set AT Command Summary (continued) Version 1.0 Lucent Technologies Inc. 5 Result Code Numeric Description CONNECT 29333 EC* 101 Connection at 29333 bit/s (V.90 mode) CONNECT 30666 EC* 102 Connection at 30666 bit/s (V.90 mode) CONNECT 33333 EC* 103 Connection at 33333 bit/s (V.90 mo[...]

  • Seite 6

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 6 Version 1.0 Lucent Technologies Inc. AT Commands Reference AT commands are issued to the modem to control the modem's operation and software configuration. AT commands can only be entered while the modem is in command mode. The format for entering AT commands is: TYPE: AT[...]

  • Seite 7

    Data Addendum Host-Based Con troller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 7 Dn Dial This command instructs the modem to begin the dialing sequence. The dial string (n, including modifiers and the telephone number) is entered after the ATD command. A dial string can be up to 60 char[...]

  • Seite 8

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 8 OK n = 1 ERROR Otherwise Hn Hook Control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. H0: Modem goes on-hook (default). H1: Modem goes off-hoo[...]

  • Seite 9

    Data Addendum Host-Based Con troller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 9 The ATI11 result has two pages; the user must hit a key to get the second page. See the following example: ati11 Description K56flex connection V.90 Connection --------------- ------------------ -------- --[...]

  • Seite 10

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 10 20. Reason for call ending, only valid after call ends: 0 = Local modem command: ATH, DTR drop 1 = Remote modem: cleardown, loss of signal 2 = No answer, busy, etc. 3 = Training failure V.90, K56flex or V.3[...]

  • Seite 11

    Data Addendum Host-Based Con troller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 11 On Return On-line to Data Mode O0: Instructs the modem to exit on-line command mode and return to data mode (see AT Escape Sequence, +++). O1: This command issues a retrain before returning to on-line d at[...]

  • Seite 12

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 12 Wn Result Code Option W0: CONNECT result code reports DTE receive speed. Disable protocol result codes. W1: CONNECT result co de reports DTE receive speed. Enable protocol result codes. W2: CONNECT result c[...]

  • Seite 13

    Data Addendum Host-Based Con troller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 13 Yn Long Space Disconnect Long space disconnect is always disabled. Y0: Disable long space disconnect (default). Y1: Enable long space disconnect (NOT SUPPORTED). Result Codes: OK n = 0 ERROR Otherwise Zn R[...]

  • Seite 14

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 14 & Dn DTR Control This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal. &D0: Ignore. The modem ignores the true status of DTR and treats it as a[...]

  • Seite 15

    Data Addendum Host-Based Con troller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 15 & Kn Local Flow Con trol Selection &K0: Disable flow control &K1: Reserved &K2: Reserved &K3: Enable RTS/CTS (hardware ) flow control (default) &K4: Enable XON/XOFF flow control Res[...]

  • Seite 16

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 16 & Sn Data Set Ready (DSR) Option This command selects DSR action. &S0: DSR always ON (default). &S1: DSR comes on when establishing a connection and goes off when the connection ends. Result Cod[...]

  • Seite 17

    Data Addendum Host-Based Con troller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 17 &V View Active Configuration and Stored Profile This command is used to display the active profiles. For example: Option Selection AT Cmd Comm Standard Bell B CommandCharEcho Enabled E Speaker Volume M[...]

  • Seite 18

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 18 & Wn Store Current Configuration This command stores certain command options and S-register values except S3, S4, and S5. The ATZ command or a power-up reset of the modem restores this profile. Result C[...]

  • Seite 19

    Data Addendum Host-Based Con troller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 19 J Bits/s Rate Adjusted This command determines whether or not the negotiated connect speed of the modem forces the adjustment of the speed of the DTE to the modem’s speed. J0: Buffer mode. Error contro[...]

  • Seite 20

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 20 N3: V.42, MNP , or buffer (default). The modem attempts to connect in V.42 error control mode. If this fails, the modem attempts to connect in MNP mode. If this fails, the modem connects in buffer mode and[...]

  • Seite 21

    Data Addendum Host-Based Con troller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 21 Tn Inactivity Timer This command specifies the length of time (in minutes) that the modem will wait before disconnecting when no data is sent or received. A setting of zero disables the timer. Alternativ[...]

  • Seite 22

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Command Reference (continued) Lucent Technologies Inc. Version 1.0 22 The table below shows the possible values: “AT-V90=X” Downstream Rate 0 V.90 disabled 1 Auto Rate (default) 2 28000 kbit/s 3 29333 kbit/s 4 30666 kbit/s 5 32000 kbit/s 6 33333 kbit/s 7 34666 kbit/s 8 36[...]

  • Seite 23

    Data Addendum Host-Based Con troller Modem June 15, 1998 AT Command Set AT Command Reference (continued) Version 1.0 Lucent Technologies Inc. 23 % Cn Data Compression Control This command determines the operation of V.42bis and MNP class 5 data compression. Online changes do not take effect until a disconnect occurs first. %C 0: V.42bis/ MNP 5 disa[...]

  • Seite 24

    Host-Based Modem Data Addendum AT Command Set June 15, 1998 24 Version 1.0 Lucent Technologies Inc. Test and Debug AT Commands The following commands are to be used for testing and debugging only and are not meant for general use. &&C Write to / Read from DSP Register AT&&C<lo c> ,<val> writes the value < val> to D[...]

  • Seite 25

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set Test and Debug AT Commands (continued) Version 1.0 Lucent Technologies Inc. 25 The modem may generate a single line or multiple lines, based on modem capabilities and call results, followed by a standard OK final result code. For example, if call setup failed, only that result i[...]

  • Seite 26

    Host-Based Modem Data Addendum AT Command Set June 15, 1998 Test and Debug AT Commands (continued) Lucent Technologies Inc. Version 1.0 26 41 3 digits 0-400 Error Control frame size 42 2 digits 0-FF Error control link timeouts X 43 2 digits 0-FF Error control link NAKs 44 Table 8 0-1 Compression Negotiation Result (Note 7) X 45 4 digits 0-200 Compr[...]

  • Seite 27

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set Test and Debug AT Commands (continued) Version 1.0 Lucent Technologies Inc. 27 Table 7 - errorControl Active from 3.5.2/V.58 Value Description Implemented 0 Disable/none X 1 V.42 LAPM X 2 V.42 Alternative protocol (MNP™) X 3-7F Reserved (V.58) 80 MNP10™ 81 ECP™ Enhanced Ce[...]

  • Seite 28

    Host-Based Modem Data Addendum AT Command Set June 15, 1998 Test and Debug AT Commands (continued) Lucent Technologies Inc. Version 1.0 28 2A CallAttemptsLimitExceeded X 2B ExtensionPhoneOffHook 2C CallSetupFailTimerExpired X 2D IncomingCallDetected X 2E LoopCurrentInterrupted 2F NoDialTone X 30 VoiceDetected 31 ReorderTone 32 SitTone 33 EngagedTon[...]

  • Seite 29

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 29 Version 1.0 Lucent Technologies Inc. AT Commands Reference S-Registers S-registers generally affect how the AT commands perform. Contents of the registers can be displayed or modified when the modem is in command mode. To display the value of an S-register: TYP E: ATSn? where[...]

  • Seite 30

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands Reference S-Registers (continued) Lucent Technologies Inc. Version 1.0 30 S4 Response Formatting Character (user defined) This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds t[...]

  • Seite 31

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands Reference S-Registers (continued) Version 1.0 Lucent Technologies Inc. 31 S8 Comma Dial Modifier Time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. Range: 0—65 Default: 2 Units: seconds[...]

  • Seite 32

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands Reference S-Registers (continued) Lucent Technologies Inc. Version 1.0 32 S21 V.24/General Bit Mapped Options Status Indicates the status of command options. Only bits 3, 4 and 5 are used, read-only. Bits 3-4 DTR behavior (& Dn) 0 = &D0 selected 1 = &D1 s[...]

  • Seite 33

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands Reference S-Registers (continued) Version 1.0 Lucent Technologies Inc. 33 S30 Inactivity Timer S30 specifies the length of time (in minutes) that the modem will wait before disconnecting when no data is sent or received. This function is only applicable to buffer mod[...]

  • Seite 34

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands Reference S-Registers (continued) Lucent Technologies Inc. Version 1.0 34 S38 K56flex Downstream Rate To force a particular K56flex downstream rate, use S-register S38. S38=0 disables K56flex, and may allow a more reliable V.34 connection. S38=1 default allows the mo[...]

  • Seite 35

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands Reference S-Registers (continued) Version 1.0 Lucent Technologies Inc. 35 S43 Auto Mode (default 1, range 0  1) This command is used for testing and debugging only. V.32bis startup auto mode operation disabled. 0 = auto mode disabled, 1 = enabled. Range: 0—1 Def[...]

  • Seite 36

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 36 Version 1.0 Lucent Technologies Inc. AT FAX Command Set (Class 1 FAX) The Lucent Technologies modem supports FAX commands conforming to EIA standard 578. These commands are given here with short descriptions; complete explanations are given in the standard, available from the[...]

  • Seite 37

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 37 Version 1.0 Lucent Technologies Inc. AT FAX Commands Reference +FCLASS? Service Class Indication This command causes the modem to display the current setting. The modem can operate either as a Class 0 data modem or a class 1 FAX modem. Typical responses: +FCLASS? 000 if in da[...]

  • Seite 38

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Fax Commands Reference (continued) Lucent Technologies Inc. Version 1.0 38 +FTM=<m> Transmit FAX Data with <m> Carrier This command causes the modem to transmit data at the modulation specified by <m>. The following table shows the values you can enter for t[...]

  • Seite 39

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Fax Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 39 +FTH=<m> Tran smit HDLC Data with <m> Carrier This command causes the modem to transmit data framed in the HDLC protocol at the modulation specified by <m>. Command Option Modulation [...]

  • Seite 40

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Fax Commands Reference (continued) Lucent Technologies Inc. Version 1.0 40 +FPR=<n > Select Fax port rate This command sets the DTE to DCE fax port rate. DTE command DCE action Description or notes •FPR • 0 Execute •IPR • 0 Select automatic rate detection •FPR[...]

  • Seite 41

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Fax Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 41 +FAA Adaptive answer A Service Class 1 Facsimile DCE may have the ability to answer as a data modem DCE or as a Facsimile DCE. It also may be able to adaptively change from Class 1 facsimile mode (•F[...]

  • Seite 42

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 42 Version 1.0 Lucent Technologies Inc. AT Voice Command Set The AT Voice Command set follows a modified IS-101 architecture. The commands are sent through the comm port, but the data path is sent either through the comm port or through a DMA channel using the wave driver. Table[...]

  • Seite 43

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 43 Version 1.0 Lucent Technologies Inc. AT Voice Commands Reference AT+FCLASS=8 Enter Voice Mode The command AT+FCLASS=8 puts the modem in voice mode. Speakerphone and TAD modes are subsumed under the more general heading of voice mode, and use a particular subset of voice mode [...]

  • Seite 44

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Voice Commands Reference (continued) Lucent Technologies Inc. Version 1.0 44 AT+VGR=<gain> Receive Gain Selection This command will enable the receive microphone gain control. ✟ <gain> is 0  255: the only useful range is 121—134 ✟ <gain>=128: nomina[...]

  • Seite 45

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Voice Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 45 AT Commands: Speakerphone Operation AT+VLS=<label> Analog Source/Destination Selection This is a general purpose analog source/destination command that attaches various analog devices to the sy[...]

  • Seite 46

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Voice Commands Reference (continued) Lucent Technologies Inc. Version 1.0 46 AT+VLS=? Analog Source/Destination Selection and DTMF/Tone Reporting Requests for the modem's DTMF/Tone reporting capabilities are made using this command. For each system configuration in voice[...]

  • Seite 47

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Voice Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 47 AT+VRA=<interval> Ringback Goes Away Timer The modem uses the ringback goes away timer when originating a call. This command sets this timer to the amount of time the modem shall wait between r[...]

  • Seite 48

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Voice Commands Reference (continued) Lucent Technologies Inc. Version 1.0 48 AT Voice Command Set Not Defined In IS-101 Specifications S32 Synthetic Ring Volume This command will provide a synthetic ring volume in dB with an implied minus sign. The default = 10. S33 Synthetic[...]

  • Seite 49

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Voice Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 49 Voice Modem Command Examples The application issues AT commands to request actions by the modem, and the modem responds with standard TIA-602 result codes to tell the application that the requested a[...]

  • Seite 50

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Voice Commands Reference (continued) Lucent Technologies Inc. Version 1.0 50 Example # 1: Initiating a speakerphone call (with phone muting during conversation) The speakerphone application is loaded. The modem is initially idle, in data mode. The user then decides to pick up[...]

  • Seite 51

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Voice Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 51 Example # 2: Initiating a stored number speakerphone call The speakerphone application is loaded. The modem is initially idle, in data mode. The user then decides to place a speakerphone call either [...]

  • Seite 52

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Voice Commands Reference (continued) Lucent Technologies Inc. Version 1.0 52 Example # 3: Answering a speakerphone call The speakerphone application is loaded. The modem is initially idle, in data mode. In this mode, the modem is always screening for incoming calls. Command D[...]

  • Seite 53

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Voice Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 53 Example # 5: Receiving an incoming data call in speakerphone or TAD mode and switching to data mode In this example, the sequence begins at the point of the user or telephone answering device (TAD) t[...]

  • Seite 54

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Voice Commands Reference (continued) Lucent Technologies Inc. Version 1.0 54 AT+VSD=128,0 DTE selects normal silence detection sensitivity, and a silence detection interval of 0 seconds. Disable silence detection. OK DCE responds. <DLE>-R DCE detects another ring, and n[...]

  • Seite 55

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Voice Commands Reference (continued) Version 1.0 Lucent Technologies Inc. 55 Example # 8: Call screening & recording a message with TAD—using the wave driver to transmit and receive voice samples The TAD application is loaded. The modem is initially idle, in data mode ([...]

  • Seite 56

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 56 Version 1.0 Lucent Technologies Inc. AT DSVD Commands In order to use the DSVD without a local phone, a ring 3 application can be used to simulate the local phone. In the absence of such an application, the voice connection needs to be auto enabled. This is accomplished by th[...]

  • Seite 57

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 57 Version 1.0 Lucent Technologies Inc. V .25ter AT Commands The + GMx commands are required by the Microsoft PC98 specifications. Manufacturer Identification (+GMI?) Read Syntax: AT+GMI? Result: Lucent Data/Fax Lucent Data/Fax/Voice/VoiceView (depending on product) Version / Re[...]

  • Seite 58

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 V.25ter AT Commands (continued) Lucent Technologies Inc. Version 1.0 58 <v8o>, <v8a>, and <v8cf> +A8I:<v8cf><CR> This indication is used by an answering DCE, if +A8E ,<v8a> !=0, to indicate detection of a V.8 CI signal, and report the recovere[...]

  • Seite 59

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 59 Version 1.0 Lucent Technologies Inc. V .80 AT Commands The chip set supports the Synchronous Access Mode and most of the commands specified in V.80 standards. The commands are either AT commands issued in the command mode, or in-band commands transmitted in the data stream. T[...]

  • Seite 60

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 V.80 AT Commands (continued) Lucent Technologies Inc. Version 1.0 60 Table 10 . V.80 AT Commands (continued) Command Sub- parameters Values Description +ESA=[< trans_idle>[,< framed _idle>[,,,< crc_type>[,< nrzi_en >]]]] trans_idle framed_idle crc_type nr[...]

  • Seite 61

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 61 Version 1.0 Lucent Technologies Inc. AT Commands for Homologation Testing and Debugging This section lists the homologation testing and debugging commands and homologation parameter values for different countries. Table 11 . The Homologation Testing and Debugging Commands Nam[...]

  • Seite 62

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 62 Table 11. The Homologation Testing and Debugging Commands (continued) Name Description Value Comments % Txx V.22 1200 originate signaling 90 Set S37 = 5 V.22 1200 answer signal[...]

  • Seite 63

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 63 Configuring for Different Countries To configure for a specific country, execute the following AT commands: AT%T19 ,0, country_code in HEX (refer to Table 2) Verify with the AT[...]

  • Seite 64

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 64 Modifying Homologation Parameters Once the modem is configured for a country, the homologation parameters shown in Table 3 can be temporarily altered for that country with the [...]

  • Seite 65

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 65 Homologation Parameters Table 13 . The Homologation Parameters Par # Parameter Description Range Reference 1 Pulse dial make time 0—255 ATD 2 Pulse dial break time 0—255 AT[...]

  • Seite 66

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 66 Table 13. The Homologation Parameters (continued) Par # Parameter Description Range Reference 19 Number of failed attempts allowed before blacklisting 0—255 ATD 1a Troubled c[...]

  • Seite 67

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 67 Table 13. The Homologation Parameters (continued) Par # Parameter Description Range Reference 31 TAD receive gain 0—255 — 32 Half/full wave ring detection 0 = halfwave, 1 =[...]

  • Seite 68

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 68 Par # Parameter Description Range Reference 4b Mercury register CIOCA LSB value—hybrid, impedance, etc. This parameter is relevant only when a Mercury line codec is used. —[...]

  • Seite 69

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 69 Country Specific Homologation Parameters Country specific values for the homologation parameters are shown in Table 14. Note : The values listed in Table 14 are typical values [...]

  • Seite 70

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 70 Table 15. The Country Specific Homologation Parameters (continued) Par. # NA Australia Belgium Denmark Finland France Germany 24 0 0 0 0 0 0 0 25 5 30 5 5 5 5 5 26 50 50 12 9 9[...]

  • Seite 71

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 71 Par. # NA Australia Belgium Denmark Finland France Germany 4d 0x1e 0x17 0x1e 0x1e 0x1e 0x1e 0x17 4e 0x13 0x13 0x13 0x13 0x13 0x13 0x13 4f 0xcd 0xcd 0xcd 0xcd 0xcd 0xcd 0xcd[...]

  • Seite 72

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 72 Table 15. The Country Specific Homologation Parameters (continued) Par. # Netherlands Italy New Zeal. Norway Spain Sweden Switzerland 1 40 41 33 36 33 40 40 2 60 65 67 64 67 60[...]

  • Seite 73

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 73 Table 15. The Country Specific Homologation Parameters (continued) Par. # Netherlands Italy New Zeal. Norway Spain Sweden Switzerland 24 0 2 0 0 0 0 0 25 27 5 5 5 5 5 5 26 10 9[...]

  • Seite 74

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 74 Par. # Netherlands Italy New Zeal. Norway Spain Sweden Switzerland 4a 0x00 0x00 0x00 0x00 0x00 0x00 0x00 4b 0x0c 0x0c 0x0c 0x0c 0x0c 0x0c 0x06 4c 0x6b 0x6b 0x6b 0x6b 0x6b 0x6b [...]

  • Seite 75

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 75 Table 15. The Country Specific Homologation Parameters (continued) Par. # UK Austria Japan China Korea Malaysia Singapore 1 34 40 34 36 32 34 32 2 68 60 66 64 64 66 64 3 1 1 1 [...]

  • Seite 76

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 76 Table 15. The Country Specific Homologation Parameters (continued) Par. # UK Austria Japan China Korea Malaysia Singapore 26 7 9 50 50 50 9 9 27 4 4 4 2 4 3 3 28 4 4 255 65 65 [...]

  • Seite 77

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 77 Par. # UK Austria Japan China Korea Malaysia Singapore 4c 0x6b 0x6b 0x6b 0x6b 0x6b 0x6b 0x6b 4d 0x17 0x1e 0x1e 0x1e 0x1e 0x1e 0x1e 4e 0x13 0x13 0x13 0x13 0x13 0x13 0x13 4f 0xcd[...]

  • Seite 78

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 78 Table 15. The Country Specific Homologation Parameters (continued) Par. # Taiwan Thailand Indonesia Ireland Portugal Hong Kong 1 36 40 36 34 33 36 2 64 60 64 67 67 64 3 1 11111[...]

  • Seite 79

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 79 Table 15. The Country Specific Homologation Parameters (continued) Par. # Taiwan Thailand Indonesia Ireland Portugal Hong Kong 23 1 11111 24 0 00000 25 5 55055 26 50 9 50 7 20 [...]

  • Seite 80

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 80 Par. # Taiwan Thailand Indonesia Ireland Portugal Hong Kong 49 0x10 0x10 0x10 0x12 0x10 0x10 4a 0x00 0x00 0x00 0x00 0x00 0x00 4b 0x0c 0x0c 0x0c 0x06 0x0c 0x0c 4c 0x6b 0x6b 0x6b[...]

  • Seite 81

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 81 Table 15. The Country Specific Homologation Parameters (continued) Par. # Canada Mexico India Vietnam Philippines 1 36 36 36 36 36 2 64 64 64 64 64 3 1 1111 4 6 6666 5 50 50 50[...]

  • Seite 82

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 82 Table 15. The Country Specific Homologation Parameters (continued) Par. # Canada Mexico India Vietnam Philippines 23 1 1111 24 0 0000 25 5 5555 26 50 50 50 50 50 27 2 2222 28 6[...]

  • Seite 83

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 83 Par. # Canada Mexico India Vietnam Philippines 49 0 0x10 0x10 0x10 0x10 4a 0x88 0x00 0x00 0x00 0x00 4b 0x80 0x0c 0x0c 0x0c 0x0c 4c 0x6b 0x6b 0x6b 0x6b 0x6b 4d 0x1e 0x1e 0x1e 0x[...]

  • Seite 84

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 84 Country Specific S Register Defaults Note : The values listed in Table 15 are typical values and change based on OEM preferences. Table 15 6. Country Specific Defaults for S Re[...]

  • Seite 85

    Data Addendum Host-Based Controller Modem June 15, 1998 AT Command Set AT Commands for Homologation Testing and Debugging (continued) Version 1.0 Lucent Technologies Inc. 85 Table 16. Country Specific Defaults for S Registers (continued) S Reg. Malaysia Singapore Taiwan Thailand Indonesia Portugal s0 000 000 000 000 000 000 s6 003 003 003 002 002 0[...]

  • Seite 86

    Host-Based Controller Modem Data Addendum AT Command Set June 15, 1998 AT Commands for Homologation Testing and Debugging (continued) Lucent Technologies Inc. Version 1.0 86 Changing the DTMF Dial Speed Default Value To change the DTMF dial speed default value, follow these steps: 1. Set par# 5 (Min DTMF dial speed) and par# 6 (Max DTMF dial speed)[...]

  • Seite 87

    For additional information, contact your Microelectronics Group Account Manager or the following: INTERNET: http://www.lucent.com/micro U.S.A.: Microelectronics Group, Lucent Technologies In c., 555 Union Boulevard, Room 30L-15P-BA, Allentown, PA 18103 1-800-372-2447 , FAX 610-712-4106 (In CANADA: 1-800-553-2448 , FAX 610-712-4106), e-mail docmaste[...]