Deutsch dropdown-ico

Martin Fireplaces BV4536 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Martin Fireplaces BV4536 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Martin Fireplaces BV4536, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Martin Fireplaces BV4536 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Martin Fireplaces BV4536. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Martin Fireplaces BV4536 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Martin Fireplaces BV4536
- Den Namen des Produzenten und das Produktionsjahr des Geräts Martin Fireplaces BV4536
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Martin Fireplaces BV4536
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Martin Fireplaces BV4536 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Martin Fireplaces BV4536 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Martin Fireplaces finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Martin Fireplaces BV4536 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Martin Fireplaces BV4536, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Martin Fireplaces BV4536 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    SUPER B-VENT GAS FIREPLACE INSTALLATION AND OPERATING INSTRUCTIONS MODELS: BV(4536,5142)(N,P)(V,E)B DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES. CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURE AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.[...]

  • Seite 2

    TABLE OF CONTENTS TABLE OF CONTENTS 1 IMPORTANT SAFETY INFORMATI ON: .................................................................................................................... 2 PRODUCT SPE CIFICATIO NS: ....................................................................................................................................... [...]

  • Seite 3

    IMPORTANT SAFETY INFORMATION IMPORTANT SAFETY INFORMATION 2 IMPORTANT SAFETY INFORMATION: INSTALLER: Please leave these instructions with the owner. OWNER: Please read and retains these instructions for future reference. IMPORTANT: Read these instructions carefully before installing or trying to operate this appliance. • DO NOT use this appliance[...]

  • Seite 4

    PRODUCT SPECIFICATIONS/LISTING & CODE APPROVAL PRODUCT SPECIFICATIONS/LISTING & CODE APPROVAL 3 PRODUCT SPECIFICATIONS: Gas Pressure (Inches W.C.) Models Number Gas Type Control Type Max Btu Max Min Manifold BV4536NV Natural Gas Milli-volt 50000 10.5 4.0 3.5 BV4536PV Propane/LPG Milli-volt 50000 13.0 11.0 10.0 BV5142NV Natural Gas Milli-vol[...]

  • Seite 5

    PRE-INSTALLATION INFORMATION PRE-INSTALLATION INFORMATION 4 PRE-INSTALLATION INFORMATION: Before You Start: Read this homeowner manual thoroughly and follow all instructions carefully. Inspect all contents for shipping damage and immediately inform your dealer if any damage is found. Do not install any unit with damaged, incomplete, or substitute p[...]

  • Seite 6

    PRE-INSTALLATION INFORMATION PRE-INSTALLATION INFORMATION 5 Figure 1: Fireplace Dimensions[...]

  • Seite 7

    PRE-INSTALLATION INFORMATION PRE-INSTALLATION INFORMATION 6 Figure 2: Fireplace Locations and Minimum Clearances Requirements CAUTION: Measure fireplace dimensions and verify framing methods & wall covering details before framing construction begins.[...]

  • Seite 8

    PRE-INSTALLATION INFORMATION PRE-INSTALLATION INFORMATION 7 Figure 3: Wall & Ceiling Minimum Clearances Wall and Ceiling Clearance Requirements: Ensure that minimum clearances shown in Figure 3 are maintained. Left and right clearances are determined when facing the front of the appliance. Follow these instructions carefully to ensure safe inst[...]

  • Seite 9

    PRE-INSTALLATION INFORMATION PRE-INSTALLATION INFORMATION 8 Mantel Clearances: If a combustible mantel is installed, it must meet the clearance requirements detailed in Figure 4. Figure 4: Mantel Clearance Floor Clearances: The fireplace may be installed on a flat, hard combustible surface (i.e. flat wood, plywood, or particleboard). Be sure that t[...]

  • Seite 10

    PRE-INSTALLATION INFORMATION PRE-INSTALLATION INFORMATION 9 CAUTION Measure fireplace dimensions and verify framing methods & wall covering details before framing construction begins. Finishing Material: NOTE Any remote wiring (i.e. remote control, wall switch or 120 volt wiring) must be done prior to final finishing to avoid costly reconstruct[...]

  • Seite 11

    VENT INSTALLATION VENT INSTALLATION 10 VENT INSTALLATION: WARNING The following venting instructions are provided as a general guideline. Always check with pipe manufacturer for venting requirements. Positioning The Fireplace: NOTE The fireplace must be installed giving full consideration to the clearance and height requirements identified in this [...]

  • Seite 12

    VENT INSTALLATION VENT INSTALLATION 11 WARNING Never use more than two (2) 45 degree elbows. When using adjustable elbows, never exceed 45 degrees. Vertical Venting with Two (2) 45 Degree Elbow: Figure 7: Horizontal Venting with Two (2) 45 Degree Elbow INSTALLING VENT COMPONENTS Before You Start: Plan your installation. Set unit in place and survey[...]

  • Seite 13

    VENT INSTALLATION VENT INSTALLATION 12 Figure 8: Installing Pipe Supports WARNING Always maintain minimum clearances around vent systems. The minimum clearances to combustibles is 1” around vent pipe. For ceiling firestops and vertical sections of vent pipe a 1-inch minimum clearance all around the pipe must be maintained. Do not pack the open ai[...]

  • Seite 14

    VENT INSTALLATION VENT INSTALLATION 13 Figure 9: Ceiling Firestop Location Vent Termination: For Vertical Termination ` Figure 10: Minimum Vent Height for Various Roof Pitches WARNING Major building codes specify a minimum vent height above the rooftop depending on the pitch of the roof. Refer to the above figure for minimum heights, provided the t[...]

  • Seite 15

    VENT INSTALLATION VENT INSTALLATION 14 NOTE When working on the roof, cover the opening of the installed vent pipes below to prevent debris falling in. To Locate and install Vertical Termination • Locate and mark the vent center point on the underside of the roof, and drive a nail through the center point. • The size of the roof hole framing di[...]

  • Seite 16

    GAS LINE AND ELECTRICAL INSTALLATION GAS LINE AND ELECTRICAL INSTALLATION 15 GAS LINE AND ELECTRICAL Gas Line Installation: NOTE Plumbing connections should only be performed by a qualified, licensed plumber. Main gas supply must be off when plumbing gas line to fireplace or performing service. • Consult all codes. All gas piping must be installe[...]

  • Seite 17

    GAS LINE AND ELECTRICAL INSTALLATION GAS LINE AND ELECTRICAL INSTALLATION 16 Figure 12: Gas Pressure Check at Gas Valve Electrical Wiring: Standing Pilot Ignition Wiring-Millivolt Control: WARNING Do not connect 110-120 VAC to the Remote Wall Switch, DC Remote Control or the Millivolt Control Valve. The appliance will malfunction or the valve will [...]

  • Seite 18

    GAS LINE AND ELECTRICAL INSTALLATION GAS LINE AND ELECTRICAL INSTALLATION 17 Figure 13: Wiring Diagram for Standing Pilot - Millivolt System Optional DC Remote Systems These instructions supersede the section entitled “Hearth Mount” in the Millivolt hand held remote instructions supplied with the remote. NOTE Remote receiver must be mounted out[...]

  • Seite 19

    GAS LINE AND ELECTRICAL INSTALLATION GAS LINE AND ELECTRICAL INSTALLATION 18 • Turn RS-ON-OFF switch to the “ON” position.  If meter is reading more than 175 millivolt and the main burner does not come on, then replace control valve.  If meter is reading less than 175 millivolt, then refer to TROUBLESHOOTING section of this manual to de[...]

  • Seite 20

    GAS LINE AND ELECTRICAL INSTALLATION GAS LINE AND ELECTRICAL INSTALLATION 19 NOTE Remote receiver must be mounted outside the appliance, due to high temperatures inside the chamber. This will prevent failures and longer battery life. 1. Plug in the remote connector wire to the remote receiver. 2. Connect the wire terminal from the remote receiver t[...]

  • Seite 21

    FINAL INSTALLATION FINAL INSTALLATION 20 FINAL INSTALLATION Wall Finishing: Definitions: Combustible Materials - Materials made of or surfaced with wood, compressed paper, plant fibers, or other materials that are capable of being ignited and burned. Such materials are considered combustible even though flameproof, fire retardant, treated, or plast[...]

  • Seite 22

    FINAL INSTALLATION FINAL INSTALLATION 21 Log Placement for fiber VDY24/18D3R: Step 1: Line up pins on bottom of Rear Log #1 with pins on grate bar and place on grate. Step 2: Place Front Left Log #2 on left front of grate bar lining up cutout in bottom of log with grate bar. Step 3: Place Front Right Log #3 on right front of grate bar lining up cut[...]

  • Seite 23

    FINAL INSTALLATION FINAL INSTALLATION 22 Glass Bi-Fold Door Installation: WARNING Glass doors must be installed on all Propane/LPG units and operated in the closed position to eliminate any potential for soot spillage into the room. When installing a natural gas unit with glass door option, the unit must be operated with glass doors completely open[...]

  • Seite 24

    FINAL INSTALLATION FINAL INSTALLATION 23 Damper operation: NOTE For Massachusetts residents only: Installation of this vented gas fireplace in the Commonwealth of Massachusetts requires the damper to be permanently removed or welded into the fully open position. In addition, a naturally vented gas fireplace may not be installed in a bedroom or bath[...]

  • Seite 25

    OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 24 Before Lighting the Fireplace: • Read the IMPORTANT SAFETY INFORMATION section at the beginning of this homeowner manual. • Before lighting, check the fireplace for possible gas leaks. • Before lighting, check for possible obstructions that could be blocking the vent termination or the front lo[...]

  • Seite 26

    OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 25 Pilot LIGHTING INSTRUCTIONS MILLIVOLT CONTROL 8. With the control knob pushed in, push in and release the piezo ignitor button to light the pilot. 9. Continue pushing the control knob in for a further 60 seconds to prevent the flame detector from shutting off the gas while the probe is warming up. Re[...]

  • Seite 27

    OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 26 FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these Instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. 5. Wait five (5) minutes to clear out any gas. Than smell for gas, including near the floor. If you smell gas, STOP! [...]

  • Seite 28

    MAINTENANCE MAINTENANCE 27 MAINTENANCE WARNING Turn off gas before servicing fireplace. It is recommended that a qualified service technician perform these check-ups at the beginning of each heating season. The appliance area must be kept clear and free from combustible materials, gasoline and other flammable vapors and liquids. The flow of combust[...]

  • Seite 29

    MAINTENANCE MAINTENANCE 28 Vent System: The fireplace and venting system should be inspected before initial use and at least annually by a qualified field service person. Inspect the external vent cap on a regular basis to make sure that no debris is interfering with the airflow. Inspect entire venting system to ensure proper function. Refer to the[...]

  • Seite 30

    PARTS LIST / ILLUSTRATIONS PARTS LIST / ILLUSTRATIONS 29 PARTS LIST / ILLUSTRATION B Firebox Components: Standard and Accessories Item Description Qty 4536 5142 1H i Temperature limit switch 1 41D0202 41D0202 2F irebrick walls (T Brown) 1 FB4536W9TB FB5142W9TB 2a Firebrick center 36” 1 41D2015 - 2b Firebrick left side 1 41D2013 41D2013 2c Firebri[...]

  • Seite 31

    PARTS LIST / ILLUSTRATIONS PARTS LIST / ILLUSTRATIONS 30 Engine Components: Standing Pilot – Millivolt Control Item Description Qty 4536NV 4536PV 5142NV 5142PV 1G as Valve Assembly 1 26D0506 26D0507 26D0506 26D0507 2P ilot Assembly 1 41D0327 41D0328 41D0327 41D0328 3 Burner Tube 1 41D0031K 41D0031K 41D0031K 41D0031K 4F lexhose with Shutoff Valve [...]

  • Seite 32

    31 Electronic Ignition Control Item Description Qty 4536NE 4536PE 5142NE 5142PE 1G as Valve Assembly 1 37D0016 37D0017 37D0016 37D0017 2P ilot Assembly 1 54D2004 54D2005 54D2004 54D2005 3 Burner Tube 1 41D0031K 41D0031K 41D0031K 41D0031K 4F lexhose with Shutoff Valve 1 23D6046 23D6046 23D6046 23D6046 5 Rocker Switch 1 41D0048 41D0048 41D0048 41D004[...]

  • Seite 33

    32 TROUBLESHOOTING STANDING PILOT - MILLIVOLT SYMPTOM POSSIBLE CAUSE REMEDY 1. Spark ignitor will not light pilot after repeated triggering of piezo. A. Wire disconnected. Open door and check to make sure wire is connected to ignitor. B. Defective ignitor. Check for spark at electrode and pilot. If no spark and electrode wire is properly connected,[...]

  • Seite 34

    33 ELECTRONIC IGNITION[...]

  • Seite 35

    34 1. Glass Soots A. Flame impingement on logs Install log set per the instructions Inspect the injector and air intake area. Make sure this area does not have any blockage from debris and clean. Check gas supply 2. Poor draft due to venting A. Too much offset. Reduce offset and/or raise termination. B. Too many elbows Reduce number of elbows C. Ve[...]

  • Seite 36

    35 LIMITED LIFETIME WARRANTY POLICY Lifetime Warranty The following components are warranted for life to the original owner, subject to proof of purchase: Firebox, Combustion Chamber, Heat Exchanger, Grate, Stainless Steel Burners, and Vented Fiber Ceramic and Refractory Logs. Basic Warranty Martin Hearth & Heating (MHH) warrants the components[...]