Middleby Marshall PS536ES Bedienungsanleitung
- Schauen Sie die Anleitung online durch oderladen Sie diese herunter
- 72 Seiten
- 8.63 mb
Zur Seite of
Ähnliche Gebrauchsanleitungen
-
Oven
Middleby Marshall PS314SBI
60 Seiten 2.5 mb -
Oven
Middleby Marshall PS840 Series
36 Seiten 3.11 mb -
Oven
Middleby Marshall PS314
72 Seiten 2.53 mb -
Oven
Middleby Marshall PS528E
60 Seiten 3.35 mb -
Oven
Middleby Marshall PS870G Gas
24 Seiten 1.1 mb -
Oven
Middleby Marshall PS570S
20 Seiten 0.92 mb -
Oven
Middleby Marshall PS224
20 Seiten 0.78 mb -
Oven
Middleby Marshall PS360/PS360WB
80 Seiten 1.3 mb
Richtige Gebrauchsanleitung
Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Middleby Marshall PS536ES an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Middleby Marshall PS536ES, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.
Was ist eine Gebrauchsanleitung?
Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Middleby Marshall PS536ES die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.
Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Middleby Marshall PS536ES. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.
Was sollte also eine ideale Gebrauchsanleitung beinhalten?
Die Gebrauchsanleitung Middleby Marshall PS536ES sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Middleby Marshall PS536ES
- Den Namen des Produzenten und das Produktionsjahr des Geräts Middleby Marshall PS536ES
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Middleby Marshall PS536ES
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen
Warum lesen wir keine Gebrauchsanleitungen?
Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Middleby Marshall PS536ES zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Middleby Marshall PS536ES und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Middleby Marshall finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Middleby Marshall PS536ES zu überspringen, wie es bei der Papierform passiert.
Warum sollte man Gebrauchsanleitungen lesen?
In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Middleby Marshall PS536ES, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.
Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Middleby Marshall PS536ES widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.
Inhaltsverzeichnis der Gebrauchsanleitungen
-
Seite 1
©2005 Middleby Marshall Inc. Middleby Middleby Middleby Middleby Middleby Marshall Marshall Marshall Marshall Marshall A MIDDLEBY COMPANY PS536-Series Electric Ovens: English owner's operating & installation manual PS536-Series O VENS Model PS536ES PS536ES (Triple) PS536ES (Double) Part No. 58367 Price $30.00 P: 10/06 ® PS536ES (Single)[...]
-
Seite 2
ii W ARNING FOR Y OUR SAFETY , DO NO T ST ORE OR USE GASOLINE OR O THER FLAMMABLE V APORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY O THER APPLIANCE. W ARNING Improper installation, adjustment, alteration, service, or maintenance can cause pr oper ty damage, injury , or death. Read the installation, operation, and maintenance instructions thorough[...]
-
Seite 3
iii MIDDLEBY MARSHALL INC. O VEN LIMITED W ARRANTY (Non U .S.A.) The Seller warrants equipment manufactured by it to be free from defects in material and workmanship for which it is responsible. The Seller ’ s obligation under this warranty shall be limited to replacing or repairing, at Seller ’ s option, without charge, F.O.B. Seller ’ s fac[...]
-
Seite 4
iv NO TE Wiring Diagrams are in Section 7 of this Manual. The diagram for each oven is also on the lower inner surface of its Control Console. TABLE OF CONTENTS Page SECTION 1 I. MODEL IDENTIFICATION .............................................. 1 SERIES PS536 ELECTRICAL SPECIFICATIONS ............. 2 II. PRINCIPLE OF AIR FLOW ....................[...]
-
Seite 5
SECTION 1 DESCRIPTION 1 I . MODEL IDENTIFICATION The Middleby Marshall PS536ES-Series may be used either as a single oven or stacked for use as double or triple ovens. The major difference between the oven models in this series is the width of the conveyor. A single PS536ES-Series Oven (Figure 1-1) is mounted on a base pad with legs and casters. A [...]
-
Seite 6
2 SECTION 1 DESCRIPTION PS536ES SERIES OVEN SPECIFICATIONS Table 1-1: Dimensions Overall Height: single oven with 17-1/2" (446mm) legs 43-1/2" (1105mm) double oven with standard 17-1/2" (446mm) legs 63" (1600mm) double oven with optional 20-1/2" (521mm) legs 66" (1676mm) double oven with optional 25-1/2" (648mm) l[...]
-
Seite 7
SECTION 1 DESCRIPTION 3 II. PRINCIPLE OF AIR FLOW The fan-style blower draws air into the oven plenum where it is heated. The blower then pushes the hot air through the air fingers into the baking chamber. Each air finger contains an inner plate and outer plate that form the hot air into jets, distributing it across a conveyor belt on which the foo[...]
-
Seite 8
4 SECTION 1 DESCRIPTION Series ovens used to bake pizza have four bottom fingers and two top fingers. For special product baking require- ments, a number of other styles of fingers and finger arrangements are available from the factory. NOTE: Some customers have a predetermined finger arrangement. If you have any questions pertaining to the finger [...]
-
Seite 9
SECTION 1 DESCRIPTION 5 III. COMPONENT FUNCTION (Figure 1-6) Figure 1-6. PS536ES-Series Oven Components Locations[...]
-
Seite 10
6 SECTION 1 DESCRIPTION III. COMPONENT FUNCTION A. Conveyor Motor and Conveyor Belt The conveyor belt is driven by a variable-speed electric motor (Figure 1-7) operating through a gear reducer. The motor speed is controlled by a digital control. The stain- less-steel wire belt can travel in either direction at variable rates ranging from 3 minutes [...]
-
Seite 11
SECTION 1 DESCRIPTION 7 Figure 1-8. Cooling Fan[...]
-
Seite 12
8 SECTION 1 DESCRIPTION Half Blank Plate Blank Plate Outer Plate Inner Plate Finger Manif old Assembly Baffle Figure 1-9. Blank Plates (two sizes) and an Air Finger. F2. Blank Plates 1. Blank Plates- The Blank Plates are available to install on the plenum where an air finger is not required.[...]
-
Seite 13
SECTION 2 INSTALLATION 9 SECTION 2 INST ALLA TION NOTE: The oven, when installed, must be electrically grounded in accordance with local codes, or in the ab- sence of local codes, with the National Electrical Code (NEC), or ANSI/NFPA70. NO TE There must be adequate clearance between the oven and any adjacent combustible con- struction. Clearance mu[...]
-
Seite 14
10 SECTION 2 INSTALLATION PS536ES OVEN INSTALLATION REQUIRED KITS AND EQUIPMENT TY P E PS536ES PS536ES PS536ES PS536ES O F Single Oven Double Oven Triple Oven Additional Cavity INSTALLATION Installation Installation Installation Installation Kit P/N Kit P/N Kit P/N Kit P/N 44919 44920 44921 44974 45529 (CE) 45530 (CE) 45531 (CE) 45532 (CE) PS536ES [...]
-
Seite 15
SECTION 2 INSTALLATION 11 Figure 2-1 - Installation Kit I. INSTALLATION KIT - see Figure 2-1 Qty. Qty. Qty. Inc. with Inc. with Single Double Triple domestic CE Item Oven Oven Oven Part No. ovens? ovens? Description 1 1 1 1 48605 Ye s Ye s Top panel 2 2 2 2 3A80A8801 Yes Yes Screw, pan head #10 x 2 ″ 3 1 1 1 42893 Ye s Ye s Base pad 4a 4 4 - - 42[...]
-
Seite 16
12 SECTION 2 INSTALLATION Figure 2-5. MODEL PS536ES SINGLE OVEN DIMENSIONS ELECTRICAL JUNCTION BOX RECOMMENDED MINIMUM CLEARANCES: Rear of Oven to Wall - 6 ″ (150mm) Non-control End of Oven to Wall - 0 ″ Control End of Oven to Wall - 0 ″ 1 2 2 2 2 1[...]
-
Seite 17
SECTION 2 INSTALLATION 13 Figure 2-6. MODEL PS536ES DOUBLE OVEN DIMENSIONS ELECTRICAL JUNCTION BOX RECOMMENDED MINIMUM CLEARANCES: Rear of Oven to Wall - 6 ″ (150mm) Non-control End of Oven to Wall - 0 ″ Control End of Oven to Wall - 0 ″ 1 2 2 2 2 1[...]
-
Seite 18
14 SECTION 2 INSTALLATION RESTRAINT CABLE INSTALLATION Install the restraint cable assembly on the oven, as shown in Figure 2-6. Figure 2-7. MODEL PS536ES TRIPLE OVEN DIMENSIONS ELECTRICAL JUNCTION BOX RECOMMENDED MINIMUM CLEARANCES: Rear of Oven to Wall - 6 ″ (150mm) Non-control End of Oven to Wall - 0 ″ Control End of Oven to Wall - 0 ″ Fig[...]
-
Seite 19
SECTION 2 INSTALLATION 15 WARNING DO NOT USE CONDUIT OR GAS LINE FOR GROUND CONNECTION. CAUTION IT IS REQUIRED THAT THE OVEN BE PLACED UNDER A VENTILATION HOOD FOR ADEQUATE AIR SUPPLY AND VENTILATION. ELECTRIC AND GAS SUPPLY TO BE PROVIDED BY CUSTOMER ELECTRICAL SAFETY SWITCH 15 Amp circuit breaker / fused disconnect switch with lockout/tagout elec[...]
-
Seite 20
16 SECTION 2 INSTALLATION II. VENTILATION GUIDELINES A mechanically driven ventilation system is required for the PS536ES Series Middleby Marshall conveyorized electric ovens. The minimum hood canopy dimensions are outlined below. Local codes and conditions vary greatly from one area to another and must be complied with. Following are the suggested[...]
-
Seite 21
SECTION 2 INSTALLATION 17 III. ELECTRICAL CONNECTION INFORMATION FOR PS536ES-SERIES OVENS. WARNING Authorized supplier personnel normally accom- plish the connections for the ventilation system, electric supply, and gas supply, as arranged by the customer. Following these connections, the factory-authorized installer can perform the initial startup[...]
-
Seite 22
18 SECTION 2 INSTALLATION Figure 2-13. Installing Rear and End Stops VI. CONVEYOR REAR STOP AND END STOP INSTALLATION Locate the conveyor rear stop and end stop in the installation kit. Install the rear stop and end stop at the exit end of the oven. See Figure 2-13.[...]
-
Seite 23
SECTION 3 OPERATION 19 SECTION 3 OPERA TION I. CONTROL FUNCTIONS WARNING A possibility of injury from rotating parts and electric shock exists in this oven. Never disassemble or clean the oven with the BLOWER/HEAT switch or any other oven control turned “ON” or “I”. Turn “OFF” or “O” and lockout or tagout all electric power to the o[...]
-
Seite 24
20 SECTION 3 OPERATION I I . COMPONENT INFORMATION AND LOCATION (Figures 3-1 and 3-2) A. Door Safety Switch The Door Safety Switch is located at the lower left side of control panel opening. Opening the control panel door permits this switch to open, disconnecting power to all electrical controls. CAUTION Do NOT touch the wires going to this safety[...]
-
Seite 25
SECTION 3 OPERATION 21 E. Conveyor The on-off switch for the conveyor motor is on the control panel. Also on the control panel is the digital conveyor speed control. The digital control can be adjusted from 3 min. to 30 min. bake time (conveyor speed). Refer to Figure 3-3. Conveyor speed is measured by the amount of time it takes for an item to go [...]
-
Seite 26
22 SECTION 3 OPERATION WARNING OVEN MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES. III. STEP-BY-STEP OPERATION Control Panel (On split belt ovens, two conveyor speed controls are mounted on the control panel.) A. Startup Procedures Daily Startup 1. Turn the BLOWER/HEAT switch (Figure 3-6) to the “ON” or “I” position. This starts the main [...]
-
Seite 27
SECTION 3 OPERATION 23 A B C D E "BLOWER" Switch: Turns the blowers and cooling fans on and off. The HEAT Switch has no effect unless the BLOWER Switch is in the “ON” position. A. "HEAT" Switch: Allows the burner to activate. Activation is determined by the settings on the Digital Temperature Controller. "CONVEYOR"[...]
-
Seite 28
24 SECTION 3 OPERATION CAUTION In case of power failure, turn all switches to the “ OFF ” ("O") position, open the oven window, and remove the product. After the power has been restored, perform the normal startup procedure. IF THE OVEN WAS SWITCHED OFF FOR LESS THAN 5 MINUTES, WAIT FOR AT LEAST FIVE MINUTES BEFORE RESTARTING THE OVEN[...]
-
Seite 29
SECTION 3 OPERATION 25 Display Shows the Set Point or the Actual T em- perature in degrees Fahrenheit (F) or Celsius (C). "SP LOCK" Light Lights when the set point is locked out from changes. This setting can only be changed by service personnel. OVERTEMP Light Lights when the oven temperature is greater than 650 ° F (343 ° C). Refer to[...]
-
Seite 30
26 SECTION 3 OPERATION IV . QUICK REFERENCE: TROUBLESHOOTING SYMPTOM PROBLEM SOLUTION The oven temperature ex- ceeded 650 ° F (343 ° C), and the burner was automati- cally shut down. • Follow the procedures under Daily Shutdown Procedures in this section to shut down the oven. Contact your Middleby Marshall Authorized Service Agent to determine[...]
-
Seite 31
SECTION 4 MAINTENANCE 27 SECTION 4 MAINTENANCE WARNING Possibility of injury from rotating parts and electrical shock exist in this oven. Turn off and lockout or tagout electrical supply to oven(s) before attempting to disassemble, clean or service oven(s). Never disas- semble or clean the oven with the blower switch or any other part of the oven t[...]
-
Seite 32
28 SECTION 4 MAINTENANCE I. MAINTENANCE - DAILY A. Exterior Everyday you should clean the outside of the oven with a soft cloth and mild detergent. WARNING Never use a water hose or pressurized steam cleaning equipment when cleaning the oven. B. Cooling Fan 1. TWO COOLING FAN GRILLES AT THE REAR OF EACH OVEN CONTROL COMPARTMENT MUST BE CLEANED DAIL[...]
-
Seite 33
SECTION 4 MAINTENANCE 29 Figure 4-3. II. MAINTENANCE - MONTHLY NOTE: The oven interior may require cleaning more than once a month depending on the volume of baking. To clean the interior, you have to disassemble some parts of the oven. When cleaning your Series PS536ES Oven note the following: PRECAUTIONS - 1. Do not use excessive water or saturat[...]
-
Seite 34
30 SECTION 4 MAINTENANCE 4. Remove conveyor drive chain cover as shown. 5. Remove tension from drive chain by lifting and pushing the conveyor slightly into the oven. Remove drive chain from conveyor drive sprocket as shown. NOTE: The split belt conveyor assembly can only be removed from the drive end of the oven. 6. Begin sliding conveyor out of t[...]
-
Seite 35
SECTION 4 MAINTENANCE 31 B. Air Fingers Disassembly For Cleaning 1. As the air fingers are removed use a felt pen to mark all parts of the fingers. This includes the finger manifold, inner plate and the outer plate (refer to Figure 1-9). If a blank or choke plate is used, mark that plate also. Fingers are marked in the order shown; as viewed from t[...]
-
Seite 36
32 SECTION 4 MAINTENANCE 6. To remove the inner plate, pull the plate out and then up. Figure 4-12. 7. The outer finger plate is stainless and may be cleaned by either soaking in a hot, strong detergent solution or using a caustic cleaner. The conveyor belt can also be cleaned in the same way. Figure 4-13. Standard Lower Finger Figure 4-14. Standar[...]
-
Seite 37
SECTION 4 MAINTENANCE 33 IMPORTANT: Only M6 Fingers fit in the bottom row. All M3 and M1 finger cover plates have extended lips at front. This extended lip will not allow these fingers to be installed in the bottom row. IMPORTANT: When inserting fingers the tab on the outer plate must be in the groove as shown in Figure 4-18. There is a blocking ta[...]
-
Seite 38
34 SECTION 4 MAINTENANCE 5. Install fingers and blank plates correctly with edges interlocked and no space between edges. Figure 4-19. Top Finger Incorrect - Too Much Space Blank Plate Tab on Outer Plate of Finger Located in Groove Top Finger Incorrect - Too Much Space Blank Plate Tab on Outer Plate of Finger Located in Groove Top Finger Correct - [...]
-
Seite 39
SECTION 4 MAINTENANCE 35 E. Reinstall End Plugs 1. Reinstall lower end plug. Be sure to tighten two wing screws on the end plug. 2. Reinstall conveyor. 3. Reinstall upper end plug. Be sure to tighten two wing screws on the end plug. Figure 4-20. Figure 4-21.[...]
-
Seite 40
36 SECTION 4 MAINTENANCE G. Checking Conveyor Belt Tension WARNING Oven conveyor belt must be cool when adjusting belt. Do not adjust belt if HOT. 1. With the conveyor assembly in the oven, stand at one end of conveyor and check tension by lifting the conveyor belt at the center of the oven chamber opening. The belt should not lift higher that 3 ?[...]
-
Seite 41
SECTION 4 MAINTENANCE 37 H. Conveyor Belt Link Removal 1. Using long nose pliers, an entire link can be removed with the conveyor assembly either in or out of the oven. Position master links at end of conveyor as shown in Figure 4-25. Figure 4-25. 2. Using long nose pliers, unhook master links at left end of conveyor as shown in Figure 4-26. Figure[...]
-
Seite 42
38 SECTION 4 MAINTENANCE I. Replacing Conveyor Belt If a section of the conveyor belt needs replacing it can be done with the conveyor assembly either in or out of the oven. The section of the conveyor belt furnished with the oven in the installation kit may then be used to replace a section. Follow the preceding procedure “ H. Conveyor belt link[...]
-
Seite 43
SECTION 4 MAINTENANCE 39 4. Reassemble conveyor drive chain cover and then reassemble the bottom cover to the drive chain cover. Install both upper end plugs. Figure 4-35. III. MAINTENANCE - EVERY 3 MONTHS WARNING Shut OFF all electrical power and lock/tag out the switch before attempting maintenance work. Shut OFF gas supply to oven. NOTE: It is r[...]
-
Seite 44
40 SECTION 4 MAINTENANCE B. Electrical Terminals Open the control cabinet door by removing the three screws from the control cabinet door. Tighten all electrical control terminal screws including the electrical contactor terminal screws as shown in Figure 4-37. Figure 4-37. Figure 4-38. C. Ventilation Check that the air circulation throughout the o[...]
-
Seite 45
SECTION 4 MAINTENANCE 41 D. Split-belt Conveyor Shaft Cleaning It is very important that the split-belt conveyor drive and idler shafts are removed from the conveyor frame for cleaning and lubrication. CAUTION Use a turbine oil or light machine oil. DO NOT USE WD40 or similar product. These oils evaporate and cause the shafts to seize. 1. Perform t[...]
-
Seite 46
42 SECTION 4 MAINTENANCE 6. Make sure bronze washer is in between the two halves. Figure 4-42. 7. Place the idler shaft assembly back into place and reinstall the adjustment screws. Figure 4-43. 8. Loosen the set screw on each conveyor drive sprocket and remove sprockets. Figure 4-44. 9. Loosen the split locking collar. Figure 4-45. 10. Remove driv[...]
-
Seite 47
SECTION 4 MAINTENANCE 43 12. Slide shaft assembly to right side, holding assembly in place. Slide split locking collar to the left side and tighten. 13. Slide rear conveyor drive sprocket onto shaft. Tighten the set screw of this drive sprocket until it extends into the hole of the hollow shaft. It should NOT touch the inner, solid shaft. Check to [...]
-
Seite 48
44 SECTION 4 MAINTENANCE KEY SPARE PARTS KIT An oven can be purchased with a Key Spare Parts Kit (Figure 4-52). (The kit can be purchased when the oven is ordered, or later, from a Middleby Marshall Authorized Parts Distributor). The kit contains many of the crucial parts that can reduce serious downtime and loss of production, if a failure occurs.[...]
-
Seite 49
45 SECTION 5 TROUBLESHOOTING SECTION 5 TROUBLESHOO TING PROBLEM: PRODUCTS ARE OVERCOOKED OR UNDERCOOKED Check for correct setting of conveyor speed control. Set the conveyor speed control at correct setting. Check for correct setting on tempera- ture controller. Turn temperature control to correct setting. If products still cook incorrectly, call y[...]
-
Seite 50
SECTION 5 TROUBLESHOOTING 46 NO TES[...]
-
Seite 51
47 ENGLISH SECTION 6 PARTS LIST SECTION 6 - P AR TS LIST[...]
-
Seite 52
48 ENGLISH SECTION 6 PARTS LIST[...]
-
Seite 53
49 ENGLISH SECTION 6 PARTS LIST OVEN PANELS, WINDOW AND LEGS ITEM QTY. P/N DESCRIPTION 1 2 A30241 NUT, 1/4-20 18-8 NYL INS L/N 2 2 A27750 WASHER, FLAT .531X1.00X.062 3 2 30927 BUMPER, WINDOW 4 1 51210 BRKT, WINDOW HINGE & STOP LEFT 5 1 51211 BRKT, WINDOW HINGE & STOP RIGHT 6 1 51087 WLDMT, GLASS FRAME WINDOW 7 1 M10092 HANDLE, WINDOW 8 1 M1[...]
-
Seite 54
50 ENGLISH SECTION 6 PARTS LIST[...]
-
Seite 55
51 ENGLISH SECTION 6 PARTS LIST CONTROL PANEL ITEM QTY. P/N DESCRIPTION 1 1 48635 BREAKER, CIRCUIT 240V 0.3A 2 2 46831 BREAKER, CIRCUIT 240V 8A 3 1 28021-0047 SWITCH, INTLCK 10A NO2P 4 2 45036 BREAKER, CIRCUIT 240V 3A 5 1 33983 CNTRL, ELEC HI-LIMIT 240V 6 1 33813 FILTER, RFI TYPE F1780DD20 7 1 O R 2 3002757 MOTOR, CONVEYOR DRIVE 8 1 31504 TFMR, 230[...]
-
Seite 56
52 ENGLISH SECTION 6 PARTS LIST[...]
-
Seite 57
53 ENGLISH SECTION 6 PARTS LIST BLOWER AND SHROUD ITEM QTY. P/N DESCRIPTION 1 2 42951 INLET RING 2a 1 42752 BLOWER WHEEL, RIGHT (VIEWED FROM REAR OF OVEN) 2b 1 42753 BLOWER WHEEL, LEFT (VIEWED FROM REAR OF OVEN) 3 2 42999 RETAINER, TEFLON SEAL 4 2 35121-0045 TEFLON SEAL 5 2 22072-0025 BEARING, 5/8" BORE WITH STANDARD GREASE - - - - 17110-0015 [...]
-
Seite 58
54 ENGLISH SECTION 6 PARTS LIST[...]
-
Seite 59
55 ENGLISH SECTION 6 PARTS LIST CONVEYOR P/N - 60" P/N - 56" P/N - 76" ITEM QTY. CONVEYOR CONVEYOR CONVEYOR DESCRIPTION 1 1 48847 48847 48790 FRAME, DRIVE SIDE 21 < - - - - 48797 - - - - > ASSEMBLY, STANDARD DRIVE SHAFT (INC. ITEMS 3-8) 31 < - - - - 48781 - - - - > DRIVE SHAFT 44 < - - - - 22229-0003 - - - - > SPROC[...]
-
Seite 60
56 ENGLISH SECTION 6 PARTS LIST[...]
-
Seite 61
57 ENGLISH SECTION 6 PARTS LIST SPLIT BELT CONVEYOR 1 1 48847 48847 48790 FRAME, DRIVE SIDE 21 < - - - - 48759 - - - - > ASSEMBLY, SPLIT DRIVE SHAFT, STANDARD AND HIGH SPEED (INC. ITEMS 3-6) 31 < - - - - 49969 - - - - > SPLIT DRIVE SHAFT - MAIN 4 1 < - - - - 48837 - - - - > SPLIT DRIVE SHAFT - SLEEVE 51 < - - - - 21415-0001 - -[...]
-
Seite 62
58 ENGLISH SECTION 6 PARTS LIST ELEMENT[...]
-
Seite 63
59 ENGLISH SECTION 6 PARTS LIST MACHINERY COMPARTMENT ITEM QTY. P / N DESCRIPTION 1 2 44914 CONTROLLER, PS555EL 208-240V 1 2 44568 CONTROLLER, PS555EL 380-480V 2 1 58238 WLDMT, HTG ELE 208V 17KW 536ES 2 1 50232 WLDMT, HTG ELE 240V 17KW 536ES 2 1 50587 WLDMT, HTG ELE 380V 17KW 536ES 2 1 50589 WLDMT, HTG ELE 480V 17KW 536ES 3 2 27480-0001 BL O CK , P[...]
-
Seite 64
60 ENGLISH SECTION 6 PARTS LIST NOTES[...]
-
Seite 65
61 SECTION 7 ELECTRICAL SCHEMATICS SECTION 7 ELECTRICAL SCHEMA TICS Wiring Diagram, E208-240 50/60, 3PH 4W PS536ES 58214E 10 AWG 613 614 10 AWG 10 AWG 10 AWG 10 AWG 10 AWG 10 AWG C1,6 BLUE BROWN C1,12 C2,12 C2,4 C2,5 C2,3 C1,4 C1,5 5 5 255 143 C1,1 228 280 607 606 610 610 248 C1,3 C2,9 C2,6 C2,7 C2,8 10 101 200 260 256 149 305 410 509 420 519 422 3[...]
-
Seite 66
SECTION 7 ELECTRICAL SCHEMATICS 62 Wiring Diagram, E380-480 50/60, 3PH 5W PS536ES 58330D 10 AWG 613 614 10 AWG 10 AWG 10 AWG 326 614 526 325 425 613 525 625 10 AWG 10 AWG 10 AWG 10 AWG C1,6 BLUE BROWN C1,12 C2,12 C2,4 C2,5 C2,3 C1,4 C1,5 5 5 255 143 C1,1 228 280 280 9 10 11 12 13 14 15 16 G L1 L2 4 5 6 -7 +8 COUNT AC -ARM +ARM AC COM 5V 5V COUNT CO[...]
-
Seite 67
63 SECTION 7 ELECTRICAL SCHEMATICS Wiring Diagram, E380V 50/60, 3PH 5W PS536ES 58267D NO2 NO2 COM2 COM2 NO1 NO1 COM1 COM1 BLOQUE DE TERMINALES KLEMMLEISTE TB3 CONTACTOR SCHALTSCHUTZ CONTROLEUR CONTROLADOR " v .. VERDE LENGUETA " GRUN ERDUNGSANSCHLUSS TERRE PATTE CONTACTOR SCHALTSCHUTZ CONTROLEUR CONTROLADOR " v v " CONTACTOR SCH[...]
-
Seite 68
SECTION 7 ELECTRICAL SCHEMATICS 64 55553C Wiring Diagram, G208-240V 50/60, GO PS536 E S FC+ FC- H.V. GV2 TH GV1 GND NC + - CONVEYOR SWIT CH GROUND LUG L1 L2 50/60 HZ 208-240V AMPLIFIER MODULA TING V AL VE 1 2 3 4 5 6 + - 4-20ma INPUT 0-24DVC OUTPUT 24V AC INPUT HEA T SWITCH TRANSFORMER 25V A 230V-24V GRD RFI-FIL TER IGNITOR SENSOR IGNITION MODULE V[...]
-
Seite 69
65 SECTION 7 ELECTRICAL SCHEMATICS NO TES[...]
-
Seite 70
SECTION 7 ELECTRICAL SCHEMATICS 66 NO TES[...]
-
Seite 71
[...]
-
Seite 72
Middleby Cooking Systems Group • 1400 Toastmaster Drive • Elgin, IL 60120 • USA • (847)741-3300 • FAX (847)741-4406 24-Hour Service Hotline: 1-(800)-238-8444 www .middleby .com Middleby is proud to support the Commercial Food Equipment Service Association (CFESA). We recognize and applaud CFESA's ongoing efforts to improve the qualit[...]