Deutsch dropdown-ico

Mitsubishi Electronics PL24FK21 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Mitsubishi Electronics PL24FK21 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Mitsubishi Electronics PL24FK21, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Mitsubishi Electronics PL24FK21 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Mitsubishi Electronics PL24FK21. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Mitsubishi Electronics PL24FK21 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Mitsubishi Electronics PL24FK21
- Den Namen des Produzenten und das Produktionsjahr des Geräts Mitsubishi Electronics PL24FK21
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Mitsubishi Electronics PL24FK21
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Mitsubishi Electronics PL24FK21 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Mitsubishi Electronics PL24FK21 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Mitsubishi Electronics finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Mitsubishi Electronics PL24FK21 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Mitsubishi Electronics PL24FK21, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Mitsubishi Electronics PL24FK21 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    OC194-1 CONTENTS 1. TECHNICAL CHANGE ··················································································OC194- 2 2. FEA TURES ·······························································?[...]

  • Seite 2

    OC194-2 1 TECHNICAL CHANGE Change points Optional par ts Program timer FK2 Switch f or temperature unit Switch f or louvers — OFF Control change of the normal and twin Change of the unit No .1 and No.2 — — P AC–SK65PT Canceled Canceled Addition of "Mode selector" ON Addition of "Not yet used" Addition of "LOSSNA Y i[...]

  • Seite 3

    OC194-3 FEA TURES 2 1. SP A CE-SA VING CENTRALL Y LOCA TED CEILING RECESSED INST ALLA TION 2. 4-W A Y AIR FLO W SYSTEM This series allows you to select from 2, 3, and 4 w a y air flow directions according to y our requirement. As a result, y ou get superb fle xibility in choosing a configuration that giv es you maximum cooling efficiency in a neat [...]

  • Seite 4

    OC194-4 3 P AR T NAMES AND FUNCTIONS Remote controller operation b uttons TIMER OFF TIMER CHECK SET TEMP . DRY COOL FAN CLOCK AUTO A UTO STAR T STOP MODE TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FIL TER CHECK TEST RUN AIR SWEEP SET TEMP . TIMER SET F FAN SPEED SWING REMOTE CONTROLLER P AR-JC240KUS AUTO RETURN FIL TER button This resets the [...]

  • Seite 5

    OC194-5 TIMER OFF TIMER CHECK SET TEMP . DRY COOL FAN CLOCK AUTO A UTO STAR T STOP MODE TIMER ON/OFF CLOCK/TIMER FAN SPEED AIR DISCHARGE FIL TER CHECK TEST RUN AIR SWEEP SET TEMP . TIMER SET F FAN SPEED SWING REMOTE CONTROLLER P AR-JC240KUS AUTO RETURN Operation lamp This lamp lights during operation, goes off when the unit stops and flashes when a[...]

  • Seite 6

    OC194-6 4 SPECIFICA TIONS Capacity P ower Consumption EER SEER INDOOR UNIT MODELS External finish P ower supply Max.fuse size (time dela y) Min.ampacity F an motor Airflow Hi-Lo Moisture remov al Sound lev el Hi-Lo Cond. drain pipe O.D . Dimensions Weight External finish Dimensions Weight OUTDOOR UNIT MODELS External finish Sound lev el P ower supp[...]

  • Seite 7

    OC194-7 Capacity P ower Consumption EER SEER INDOOR UNIT MODELS External finish P ower supply Max.fuse size (time dela y) Min.ampacity F an motor Airflow Hi-Lo Moisture remov al Sound lev el Hi-Lo Cond. drain pipe O.D . Dimensions Weight External finish Dimensions Weight OUTDOOR UNIT MODELS External finish Sound lev el P ower supply Max. fuse size [...]

  • Seite 8

    OC194-8 5 DA T A MODELS : PL12FK 1 , PL18/24/30FK2 1 , PL36FK3 1 , PL42FK2 1 1. PERFORMANCE D A T A 1) COOLING CAP ACITY Models Indoor air Outdoor intake air DB temperature ( °F ) PL12FK 1 71 67 63 71 67 63 71 67 63 71 67 63 71 67 63 71 67 63 TC 14.3 13.2 12.1 21.2 19.8 18.5 27.4 25.6 23.8 35..8 33.2 30.9 41.7 38.9 36.4 49.6 46.1 42.8 SHC 7.1 8.4 [...]

  • Seite 9

    OC194-9 2. PERFORMANCE CUR VE NO TES : A point on the curve shows the ref erence point. PL12FK 1 COOLING CAP A CITY PL18FK2 1 COOLING CAP A CITY T otal power consumption (kW) T otal capacity (x10 3 Btu/h) Outdoor intake air DB temperature ( F) 24 21 12 18 15 2.5 2.0 1.5 1.0 63 67 71 63 67 71 SHF=0.76 0 32 35 45 55 65 (67) 75 85 95 105 115 Indoor in[...]

  • Seite 10

    OC194-10 NO TES : A point on the curve shows the ref erence point. PL24FK2 1 COOLING CAP A CITY PL30FK2 1 COOLING CAP A CITY T otal power consumption (kW) T otal capacity (x10 3 Btu/h) Outdoor intake air DB temperature ( F) 36 30 42 24 4.0 3.5 3.0 2.5 63 67 71 63 67 71 SHF=0.76 23 32 35 45 55 65 (67) 75 85 95 105 115 Indoor intake air WB temperatur[...]

  • Seite 11

    OC194-11 <PL18FK2 1 > COOLING MODE 3. CONDENSING PRESSURE AND SUCTION PRESSURE Data is based on the condition of indoor humidity 50%. Air flow should be set at HI. A point on the cur ve sho ws the reference point. <PL12FK 1 > 350 340 330 320 310 300 290 280 270 260 250 240 230 220 210 200 190 180 170 160 150 (psi.G) Condensing pressure [...]

  • Seite 12

    OC194-12 Data is based on the condition of indoor humidity 50%. Air flow should be set at HI. A point on the cur ve sho ws the reference point. <PL24FK2 1 > <PL30FK2 1 > COOLING MODE 350 340 330 320 310 300 290 280 270 260 250 240 230 220 210 200 190 180 170 160 150 (psi.G) Condensing pressure 30 40 50 60 70 80 90 100 110 Outdoor ambien[...]

  • Seite 13

    OC194-13 Data is based on the condition of indoor humidity 50%. Air flow should be set at HI. A point on the cur ve sho ws the reference point. <PL36FK3 1 > <PL42FK2 1 > COOLING MODE 350 340 330 320 310 300 290 280 270 260 250 240 230 220 210 200 190 180 170 160 150 (psi.G) Condensing pressure 30 40 50 60 70 80 90 100 110 Outdoor ambien[...]

  • Seite 14

    OC194-14 4. ST AND ARD OPERA TION D A T A 750 750 750 750 760 760 840 840 Capacity SHF Input INDOOR UNIT MODEL Power supply (V, phase, Hz) Input Fan current OUTDOOR UNIT MODEL Power supply (V, phase, Hz) Input Comp. current Fan current Condensing pressure Suction pressure Discharge temp. Condensing temp. Suction temp. Ref. pipe length Refrigerant c[...]

  • Seite 15

    OC194-15 90 80 70 60 50 40 30 20 10 63 125 250 500 1000 2000 4000 8000 APPRO XIMA TE THRESHOLD OF HEARING FOR CONTINUOUS NOISE NC-60 NC-50 NC-40 NC-30 NC-20 NC-70 OCT A VE BAND SOUND PRESSURE LEVEL, dB re 0.002 MICR O BAR BAND CENTER FREQUENCIES, Hz PL12FK 1 Hi Lo 43 SPL(dB) 35 LINE NO TCH 7. NOISE CRITERION CUR VES Airflow Air speed Coverage range[...]

  • Seite 16

    OC194-16 90 80 70 60 50 40 30 20 10 63 125 250 500 1000 2000 4000 8000 APPRO XIMA TE THRESHOLD OF HEARING FOR CONTINUOUS NOISE NC-60 NC-50 NC-40 NC-30 NC-20 NC-70 OCT A VE BAND SOUND PRESSURE LEVEL, dB re 0.002 MICR O BAR BAND CENTER FREQUENCIES, Hz PL24FK2 1 Hi NO TCH Lo 47 SPL(dB) 39 LINE 8. NOISE CRITERION CUR VES 90 80 70 60 50 40 30 20 10 63 1[...]

  • Seite 17

    OC194-17 OUTLINES AND DIMENSIONS 6 Unit : inch 1. INDOOR UNIT PL12FK 1 / 18/24FK2 1[...]

  • Seite 18

    OC194-18 Unit : inch PL30FK2 1 / 36FK3 1 / 42FK2 1[...]

  • Seite 19

    OC194-19 Unit : inch 2.Remote controller FILTER CHECK MODE TEST RUN TIMER OFF TIMER CHECK SET TEMP . CLOCK AUTO A UTO STAR T STOP SWING FAN SPEED 5-1/8 4-3/4 3/4 3/32 23/32 AUTO RETURN FAN Indoor coil thermistor RT2 Distributor Refrigerant pipe (option) { 3/8" (with heat insulator) Refrigerant pipe (option) { 5/8" (with heat insulator) St[...]

  • Seite 20

    OC194-20 WIRING DIA GRAM 8 MODELS PL12FK 1 PL18FK2 1 PL24FK2 1 WIRING DIA GRAM SYMBOL C1 CN1<R.B> CN2<R.B> CN51<I.B> CN2L<I.B> DP DS F1<I.B> F2 H2 I.B LS MF1 MV R.B NAME F an motor capacitor Connector <program timer> Connector <remote switch> Connector < centrally control> Connector <lossnay> Dr[...]

  • Seite 21

    OC194-21 MODELS PL30FK2 1 PL36FK3 1 PL42FK2 1 WIRING DIA GRAM NO TES: 1.Since the outdoor side electric wiring may change be sure to check the outdoor unit electric wiring for servicing. 2.Indoor and outdoor connecting wires are made with polarities,make wiring matching terminals. 3.Symbols used in wiring diagram abov e are, :T er minal block, , :c[...]

  • Seite 22

    OC194-22 9 OPERA TION FLO W -CHART START Power circuit breaker Check SW ON twice Operation SW ON “OFF” timer “ON” timer STOP Set time complete Set time complete 1 NO NO NO NO NO NO NO NO NO YES YES YES YES YES YES YES YES YES YES w 1 w 2 w 3 w 4 w 5 PROTECTION DEVICE SELF HOLD RELEASE Remote controller indicator lamp OFF Trouble STOP Remote[...]

  • Seite 23

    OC194-23 COOL operation Initial COOLING NO NO NO NO NO YES YES YES YES YES YES NO YES YES YES YES YES YES YES YES YES YES YES NO NO NO NO YES NO NO NO NO NO NO NO NO NO w 8 w 9 Vane initial setting Vane 55 deg downward angle 70 deg downward angle Fan speed LOW Downward discharge 1 hour Vane setting notch Vane horizontal airflow Compressor thermosta[...]

  • Seite 24

    OC194-24 w 8—9 Ref er to page OC194-23. w 12 When room temperature is 64°F or below , the compressor cannot operate. When room temperature rises ov er 64°F the compressor star ts after a 3-minute time dela y . w 13 Compressor ON time is decided by room temper ature. Refer to page OC194-29. w 14 In dry operation, compressor ON makes the f an spe[...]

  • Seite 25

    OC194-25 MICR OPROCESSOR CONTR OL 10 ● Compressor and outdoor f an : ON- OFF 1.OUTLINE OF MICROPR OCESSOR CONTROL ● OFF-ON s witching. ● COOL/DR Y -F AN selector s witching. ● Thermostat setting. ● TIMER mode selector-s witching and Timer setting. ● HIGH-LO W fan speed s witching. ● A UTO V ane selector (AIR DISCHARGE) s witching. ●[...]

  • Seite 26

    OC194-26 2. INDOOR UNIT CONTROL 2-1 COOL operation (1) Compressor control 1 3-minute time dela y T o prev ent overload, the compressor will not star t within 3 minutes after stop . 2 The compressor runs when room temperature is higher than set temperature. The compressor stops when room temperature is equal to or low er than the set temperature. Th[...]

  • Seite 27

    OC194-27 5 Coil frost protection When indoor coil temperature becomes 5°F or below ,coil frost protection will proceed as follo ws. <Start condition> After the compressor has been continuously operated f or 3 minutes or more,and the indoor coil temperature has been 5°F or below f or 3 minutes,the coil frost protection will star t. <Coil [...]

  • Seite 28

    OC194-28 (4) Detecting abnormalities in the outdoor unit After the compressor has been continuously operated f or 3 minutes, if the diff erence between the indoor coil temperature and room temperature is out of RANGE C f or 1 minute, the indoor fan speed will turn to LO W . Five min utes later , if the dif- f erence is still out of RANGE C,the outd[...]

  • Seite 29

    OC194-29 <DR Y operation time chart> Minimum 3 minutes w 1 ON Thermostat Indoor fan Auto vane Drain pump Compressor ON ON DRY MODE DRY MODE ON OFF OFF ON OFF 3 minutes OFF OFF Operation starts by POWER button ON. Operation stops by POWER button OFF. Room temperature becomes equal to set temperature. Room temperature rises above set temperatur[...]

  • Seite 30

    OC194-30 4 The compressor will not star t when the room temperature is 64°F or below . The compressor star ts inter mittent operation when the power is turned ON with room temperature abov e 64°F . The com- pressor ON/OFF time depends on the thermostat ON/OFF and the following room temper atures.After 3-minute compres- sor operation, ● If the r[...]

  • Seite 31

    OC194-31 <How to operate> T o change the air flow direction, press AIR DISCHARGE button. 1 20° 2 45° 3 60° 45 70° SWING (1) COOL/DR Y operation At the star t-up of COOL or DR Y operation, the airflo w direction in automatically set to 20°. After , it can be changed to another direction with AIR DISCHARGE button on the remote controller .[...]

  • Seite 32

    OC194-32 <Timer function> A UTO ST OP ··········The air conditioner stops after the set time lapses. A UTO ST AR T ········The air conditioner star ts after the set time lapses. A UTO OFF ············Timer is not active. <How to operate> 1. Press POWER ON/OFF button. 2. Press “TIMER ON/OFF” button to se[...]

  • Seite 33

    OC194-33 (1) Indoor coil temperature code During the test r un, the indoor coil temperature code from 1 to 15 is displa yed on the remote controller instead of room temperature. The code should f all with the lapse of time in nor mal COOL operation, and should rise in nor mal HEA T operation. (2) T rouble during test run ● If the unit malfunction[...]

  • Seite 34

    OC194-34 3 DIP SWITCH FUNCTIONS Each figure shows the initial setting b y f actor y . 3-1 On remote controller boar d (1) SW17(Address selector) SW17-1 ~ 6) Switch f or address setting SW17-7) When two remote controllers are used, this switch sets the controller function. OFF : The remote controller is set as a main controller . ON : The remote con[...]

  • Seite 35

    OC194-35 SW1-6) Switch f or set temperature adjustment in heating mode This is not av ailable for series PL. SW1-7) Switch f or fan speed during ther mostat OFF in heating mode This is not av ailable for series PL. SW1-8) Switch f or fan motor operation in heating mode This is not av ailable for series PL. SW1-9) Switch f or outdoor unit abnor mali[...]

  • Seite 36

    OC194-36 11 TR OUBLESHOO TING The displa y “CENTRALL Y CONTROLLED” on remote controller does not disap- pear . 1) Wrong address setting of remote con- troller/indoor controller board. 2) Timer adapter is connected to the remote controller . 3) Signal transmission error between indoor unit and remote controller . 1) Check the address setting of [...]

  • Seite 37

    (2) When one remote controller controls seve ral units in the group con- trol, the LCD shows the unit address and chec k code of the first mal- functioning unit. (3) T o cancel the check mode , press the ON/OFF button. In remote ON/OFF control, press the remote ON/OFF s witch. In centralize control, turn OFF the ON/OFF button of centralize controll[...]

  • Seite 38

    OC194-38 1) Check the indoor/outdoor connecting wire . 2) Change the connection of electric wir ing. 3) Check the protection de vice. 4) Measure the resistance of the outdoor coil ther- mistor . If the resistance is normal, replace the outdoor controller board. Check code Diagnosis of malfunction Cause Check points E0 Signal transmitting/receiving [...]

  • Seite 39

    OC194-39 Wrong wiring Thermostat Phenomenon Outdoor Indoor 1 2 3 1 2 3 OFF Operation stops. ON 4-W ay v alve is turned to ON. 9 minutes later , the check code “P8” appears on the remote controller displa y . Outdoor Indoor 1 2 3 1 2 3 OFF The outdoor unit stops. ON Operation stops. 9 minutes later , the check code “P8” appears on the remote[...]

  • Seite 40

    OC194-40 V anes do not work. V ane motor does not work. Connector is poorly connected. V ane motor is poorly assembled. Indoor controller board is damaged. Unit stops after 5 to 20 seconds operation Protection function is working. Air discharge displa y is OFF and AIR DIS- CHARGE button does not operate. Indoor controller board deems the auto vanes[...]

  • Seite 41

    OC194-41 4. How to chec k the par ts PL12FK 1 /18FK2 1 /24FK2 1 /30FK2 1 /36FK3 1 /42FK2 1 P ar ts name Check points Disconnect the connector then measure the resistance using a tester . (Surrounding temperature 50 - F~86 - F) Measure the resistance between the terminals using a tester . (Surrounding temperature 68 - F~86 - F) Measure the resistanc[...]

  • Seite 42

    OC194-42 0 10 20 30 40 50 -4 14 32 50 68 86 104 122 < Thermistor for lower temperature > T emperature ( - F) Resistance (K " ) <Thermistor Character istic graph> Room temperature thermistor(TH1) Liquid pipe thermistor(TH2) Ther mistor R 0 =15k ' ± 3% Fix ed number of B=3480k ' ± 2% Rt=15e xp { 3480( ) } 32°F 15k '[...]

  • Seite 43

    OC194-43 4-W A Y AIR FLO W SYSTEM 12 Using this grill enables to select the air discharge direction. The air flow can also be regulated b y adjusting the widths of each discharge outlet. Choose the adequate method according to the conditions in the room where the panel is to be installed. W F or 2-direction discharge, the widths of the outlets must[...]

  • Seite 44

    OC194-44 Opening measurements f or PLH30/36/42FK 1 are within ( ). ● ● Regular ceiling height When ceiling is of regular height (F or example 8.2ft) set each out- let at a standard width (11-13/16). ● ● Relativel y high ceiling Set the outlets during installation. The outlet width can be adjusted in the range of 7-7/8 to 11-13/16 using the [...]

  • Seite 45

    OC194-45 Selecting arrangement of discharge outlet and adjusting the width f or PL12FK 1 / 18/24FK2 1 . Constrained Conditions When Selecting Discharge Outlet Width. (PL18/24FK2 1 ) T otal width of four outlets must e xceeds 31-1/2. Unit : inch (1) When the outlet A is close to a window, widen A and narrow C to raise the cooling power of A. e.g. 1 [...]

  • Seite 46

    OC194-46 Selecting arrangement of discharge outlet and adjusting the width f or PL30FK2 1 / 36FK3 1 / 42FK2 1 . Constrained Conditions When Selecting Discharge Outlet Width. (PL30/36/42FK) T otal width of four outlets must e xceeds 55-1/8. Unit : inch When the unit is installed near a window, the longer outlet (B or D) must be in direction of the w[...]

  • Seite 47

    OC194-47 FRESH AIR INT AKE (Installation at site) 1. Location for installing fresh air intake 2. Air flow & static pressure conditions f or fresh air intake Detail drawing of fresh air intak e Be sure to use a duct f an (booster fan) when applying fresh air intake . As f or sequential operation with the duct f an, see Item 3. 3. Sequential oper[...]

  • Seite 48

    OC194-48 BRANCH DUCT (installation at site) 1. Branch Duct Installation Pr ocedure 2. Branch Duct Installation T o discharge air from a branch duct, install it during the initial installation. Install branch duct at site b y follo wing procedure (1) Remo ve insulation along the brok en-lines on unit surf ace at the back-side of the indoor unit. Kno[...]

  • Seite 49

    OC194-49 3 direction discharge 4 direction discharge () 25-9/16 O O 2 directions 11-13/16 O O 2 directions 3 direction discharge () 35-7/16 O O 1 directions 11-13/16 O O 2 directions Branch duct (3-15/16) (11-13/16) (27-9/16) (35-7/16) Static pressure [in.W.G O 10 –2 ] 0 50 100 150 200 250 300 350 400 450 500 550 20 16 12 8 4 Air capacity [CFM] S[...]

  • Seite 50

    OC194-50 13 SYSTEM CONTR OL Unit Remote control display board Remote controller Unit Unit T wo remote controllers can be used to control either one unit or a group of units. Units can then be controlled from a distance or at close range. Units operate according to the latest command from either remote controller . 1 Group control with a single remo[...]

  • Seite 51

    OC194-51 2. GROUP CONTR OL BY A SINGLE REMO TE CONTROLLER A maximum of 50 units can be star ted in order according to the dip switch settings 2-1 How to wire (1) Connect the remote controller to the double terminal bloc k on the indoor controller board of the master unit, that is, No .0 unit. (See Figure 1.) (2) Connect the double terminal bloc k o[...]

  • Seite 52

    OC194-52 3. CONTROL USING TW O REMO TE CONTROLLERS T wo remote controllers can be used to control either one unit or a group of units. Units operate according to the latest com- mand from either of the two remote controllers. Bef ore operation, be sure to set one remote controller as the “main controller” and the other as the “sub controller?[...]

  • Seite 53

    OC194-53 NO TE1 : Install the relay bo x where you can be ser viced it easily . NO TE2 : For control circuit wiring, use a wire of No . 14 A WG or a control cable according to the po wer supply of control circuit. NO TE3 : When the power supply of the control circuit is 208/230V A C , ● Do not connect the control circuit wire to the remote contro[...]

  • Seite 54

    OC194-54 6. MUL TIPLE REMO TE CONTROL DISPLA Y Y ou can control se v eral units with a multiple remote control displa y , by wiring an optional multiple display adapter (P A C-SA88HA-E) with relays and lamps on the market. How to wire (1) Connect the multiple displa y adapter to the connector CN51 on the indoor controller board. (2) Wire three of t[...]

  • Seite 55

    OC194-55 DISASSEMBL Y PR OCEDURE 14 OPERA TING PROCEDURE PHO T OS&ILLUSTRA TIONS 1. Removing the air intake grille (1) Slide the le ver in the direction of the arro w 1 . (2) Open it 90 deg. (3) Slide the intake g rill in the direction of the arrow 2 and remov e it. (4) Slide the two knobs on the left and right in the direction of the arrow 3 a[...]

  • Seite 56

    OC194-56 OPERA TING PROCEDURE PHO T OS&ILLUSTRA TIONS 4. Removing the drain pump, drain sensor , and indoor coil thermistor (1) Remov e the fan (nut). (2) Remov e the electr ical box (3 scre ws). (3) Remov e the ser vice panel screws (2 pcs). (4) Hold the knob and remov e the ser vice panel. (5) Remov e the drain pump set screws (2 pcs). (6) Re[...]

  • Seite 57

    OC194-57 15 P AR TS LIST PL12FK, PL18FK2, PL24FK2 P ANEL P ARTS PL12FK 1 , PL18FK2 1 , PL24FK2 1 1 2 3 4 5 6 1 1 1 4 1 1 1 1 1 4 1 1 1 1 1 4 1 1 1 1 1 4 1 1 MV F2 INDOOR PANEL 250V 0.5A No. Parts No. Parts Name Specifications Drawing No. Q'ty/set Price Unit Amount Remarks Circuit Diagram Symbol Recom- mended Q'ty PL 12 18 24 FK2 FK2 1 FK2[...]

  • Seite 58

    OC194-58 PL12FK, PL18FK2, PL24FK2 FUNCTIONAL P ARTS PL12FK 1 , PL18FK2 1 , PL24FK2 1 2 3 16 17 18 15 26 5 1 11 14 19 21 24 27 6 7 8 10 12 13 4 9 25 23 20 22 29[...]

  • Seite 59

    OC194-59 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 3P (L1,N,GR) 2P (1,2) 2P (1,2) 2P (1,2) SGR-25 DTC SGR-37 DTC 12 + 220V 8.5 + 220V 250V 6A 3P (L1,N,GR) 39ft 33ft TB2 TB5 TB4 TB4,5 MF1 MF1 C1 C1 I.B I.B F1 TB[...]

  • Seite 60

    OC194-60 PL30FK2, PL36FK3, PL42FK2 FUNCTIONAL P ARTS PL30FK2 1 , PL36FK3 1 , PL42FK2 1 2 3 27 27 5 15 16 17 18 1 4 7 8 9 10 12 13 11 6 16 14 20 22 25 19 24 26 21 23 29[...]

  • Seite 61

    OC194-61 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 1 1 1 2 2 2 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 1 6 1 1 1 2 2 2 2 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 6 1 1 1 1 1 2 2 2 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 1 6 1 1 1 2 2 2 2 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 6 1 1 TB2 TB5 TB4 TB4,5 MF1,2 MF1,2 C1,2 I.B I.B F1 TB12 T DP[...]

  • Seite 62

    OC194-62 1 2 3 4 5 6 1 1 2 8 2 1 1 1 2 8 2 1 1 1 2 8 2 1 1 1 2 8 2 1 MV F2 INDOOR PANEL 250V 0.8A No. Parts No. Parts Name Specifications Drawing No. Q'ty/set Price Unit Amount Remarks Circuit Diagram Symbol Recom- mended Q'ty PL 30 36 42 FK2 FK2 1 FK3 FK3 1 FK2 FK2 1 1 1 2 8 2 1 1 1 2 8 2 1 T7W 413 003 T7W 410 223 R01 K01 500 R01 K01 054[...]

  • Seite 63

    OC194-63 OPTIONAL P AR TS 16 1-2 Feature of program timer (1) Daily timer function Daily timer can be set in 30 minutes units f or up to 24 hours. Each unit can be set f or unit ON, unit OFF , or setbac k operation. (2) Setback oper ation (P AC-SC32PT A) Set back oper ation is useful for reducing running costs e.g. At a hotel with a 24-hour system [...]

  • Seite 64

    OC194-64 1-4 Names and functions <P AC-SC32PT A> WEEKL Y TIMER SETTING DISPLA Y Sets timer for a w eek. SET/MONITOR SET SM TWT F S MONITOR PROGRAM TIMER PAC-SC32PTA TODAY ON WEEKLY SETTING OFF ON SET BACK OFF CLOCK DAILY TIMER SET BACK SET BACK DAILY SETTING 12 15 18 21 24 036 1 2 15 CURRENT TIME DISPLA Y During MONITOR status ,current time i[...]

  • Seite 65

    OC194- 65 1 2 3 4 5 BRN RED ORN YLW GRN 3. MUL TIPLE REMO TE CONTROLLER AD APTER This adapter is needed f or remote indication (operation/check). Adapter connection is described on page 49. P ar t No. P AC-SA88HA-E Pa r t N o. Applicable Model P AC-SG03TM-E PL12/18/24/30/36/42FK Pa r t N o. Applicable Model P AC-SG01KF PL12/18/24/30/36/42FK 5. HIGH[...]

  • Seite 66

    © Copyright 2000 MITSUBISHI ELECTRIC ENGINEERING CO .,L TD . Distributed in Jun. 2001. No.OC256 REVISED EDITION-B 20 Distributed in Mar . 2001. No.OC256 REVISED EDITION-A 20 Distributed in Dec. 2000. No.OC256 nPrinted in Atlanta 07/2001 New pub lication, effectiv e Jun. 2001 Specifications subject to change without notice Oc256b~1.qxd 7/20/2001 10[...]

  • Seite 67

    3400 Lawrenceville Suwanee Road ● Suwanee, Georgia 30024 Toll Free: 800-433-4822 ● Toll Free Fax: 800-889-9904 www.mrslim.com Specifications are subject to ch ange without notice.[...]