Montgomery Ward TMO-33986C Bedienungsanleitung

[...]

Safe Operation Practices Assembly Instructions. . Controls. Operation. Adjustments Lubrication. Maintenance Off-Season Storage. 19 21 22,24,26,28,3023,25,27,29,31 32,34 33,35 Back Cover NOTICE: A data plate with the model number and serial numbers of your unit is located on the frame, under the seat. Record these numbers in the spaces provided on t[...]

(t) :C~~~EI~Ej To reduce the potential for any injury, comply with the following safety instructions. Failure to comply with the instructions may result in personal injury. SAFE OPERATION PRACTICES FOR RIDING VEHICLES 1. Read this owner's manual carefully in its en- 16. Disengage power to attachment(s) and stop tirety before attempting to asse[...]

(2) Never make a cutting height adjustment while engine is running if operator must dismount to do so. (3) Shut the engine off and wait until the blade comes to a complete stop before removing the grass catcher. (4) Check blade mounting bolts for proper tightness at frequent intervals. 34. Check grass catcher bags frequently for wear or deteriorati[...]

BATTERY INFORMATION ~ ~A_R~I_N? -_t D. Since battery acid is corrosive, do not pour it into any sink or drain. Before discarding empty electrolyte containers, rinse :hem with a neutralizing solution.E. NEVER connect or disconnect charger clips to battery while charger is turned on as it can cause sparks. F. Keep all lighted materials (cigarettes, m[...]

9. The battery can be charged after the 20 minutes sitting period. SLOW CHARGE THE BATTERY (DO NOT FAST CHARGE) at a max- imum bench rate of 1.4 amperes until the specific gravity reading is 1.260-1.280. Charge for a minimum of 2 hours and a maximum of 8 hours. Battery contains sulfuric acid. Refer to warning on page 5. Antidote: EXTERNAL-Flush wit[...]

3. Lift the transmission cover. Unplug the green safety wire from beneath the transmission-cover. See figure 6. Remove transmission cover. FIGURE 6. 4. Place the battery in the lawn tractor so that the positive terminal is facing the right side of-the unit. See figure 7. NOTE Right and left hand sides of the unit are determined from the operating p[...]

8. Push the locking end of cable tie (I) through~the hole in the left frame as shown in figure 9. Route 1he battery drain tube back to the cable tie. Place end of cable tie through the slot so a loop is formed around the drain tube to secure it. Tighten cable tie and cut off excess end.9. Plug the green safety wire into the switch beneath the trans[...]

3. Place steering wheel and bellow on the steer- ing shaft, lining up the flats in the wheel with the flats on the shaft.4. Secure with belleville washer (6) (cupped side against the steering wheel) and hex nut (C). ~ See figure 12. 5. Press the steering wheel cap (A) on the steer- ing wheel by hand. SEAT INSTAllATION The seat may be adjusted to fo[...]

CUTTING CONTROLS CLUTCH.BRAKE PEDALThe clutch-brake pedal is located on the right side of the lawn tractor. Depressing the clutch-brake pedal part way disengages the clutch. Pressing the pedal all the way down disengages the clutch and engages the disc brake. See figure 15. A. LIFT AND DISENGAGEMENT LEVER The lift and disengagement lever is used to[...]

OPERA TION Do not operate the lawn tractor if the interlock system is malfunction- ing because it is a safety device, designed for protection. 4. Set the throttle control in the CHOKE posi- tion. See figure 14.5. Turn the ignition key to the "START" position. When the engine is running, let the key return to the "ON" position. S[...]

7. The lawn tractor is brought to a stop by depressing the clutch-brake pedal. The drive belt will be disengaged and the brake will be applied. NOTE ~ CAUTION If the unit is not to be used for a long period, place the gear shift lever in NEUTRAL, stop the engine, set the parking break and remove the key. DO NOT leave the machine on an incline. Unde[...]

J r---~ Front of Tractor -- --- L J R FIGURE 20. TOE-IN DIAGRAM CARBURETOR ADJUSTMENT ', ~ WARNING t ' If any adjustments are made to the engine while the engine is running(e.g. carburetor), disengage allclutches, and blades. Keep clear of all moving parts. Be careful of heated surfaces and muffler. FIGURE 18. WHEEL ADJUSTMENTThe caster [...]

FIGURE 21. 3. Tighten the outside nut against the inside nut, using two 1/2 II wrenches. See figure 22. NOTE Friction pads must be replaced when the inside of cam lever touches the housing. FIGURE 23. STEERING SHAFT Lubricate steering shaft at least once a season with light oil. TRANSAXLE The transaxle is lubricated and sealed at the fac- tory and [...]

The blade can be tested for balance by balancing it on a round shaft screwdriver. Remove metal from the heavy side until it balances evenly. NOTE It is recommended that the blade always be removed from the adapter for the best test of balance. AIR CLEAN ER Under normal operating conditions, the air cleaner, located on top of the carburetor, must be[...]

FIGURE 26. 3. Remove the engine pulley belt guard by slip. ping it back and to the right. See figure 27. FIGURE 24. 3. Unhook the deck belt from the engine. pulley. 4. Place the lift lever in the engaged (all the way forward) position. 5. Disconnect the six deck links by removing the hairpin cotters and flat washers. 6. Slide the deck from beneath [...]

G.ound 10 F,.m. 2 / _3 1 I ~ ,j II Vr G'~un. 8 ~ ~ 81ue 7 81ac ~ ". "'4 ~_. 6, Tecum.e" Eng;ne ~'-:--"'",,[==J 9 10, r-E ---4 I r "I -' T~~ I I f ;. 0' j ,Ic ~- -:--~~ !;Ic',2;,,-:C,," ,.. ~ ,.a --<5 16 , I. ~ 13 ~ ~ ~ & = ==::~~-~ "'O". _ I /~ SI.&apos[...]

[...]

TM Q.33902A T M Q.33886C 10 H.P. 38// LAWN TRACTORS PARTS LIST FOR MODELS TMO.33902A AND TMO-33886C REF, NO. T! 3 ' 4 PART NO. PART NO. 726-0222 14607 712-0267 736-0119 757-0264 710-0726 REF.I ~I 48 50 51 52 54 57 DESCRIPTION DESCRIPTION 732-0414 14665 -615 712-0272 736-0463 723-0302 710-0473 5 6 59 61 63 731-0561 726-0151 710-0227 7 8 9 10 [...]

[...]

[...]

[...]

[...]

[...]

[...]

[...]

[...]

[...]

[...]

[...]

[...]

HOW TO 08T AIN REPLACEMENT PARTS AND SERVICE The merchandise you have purchased from us has been carefully engineered and manufactured under Wards rigid quality standards and should give you satisfactory and dependable operation. However, like all mechanical merchan- dise, it may occasionally require adjustment, replacement parts or maintenance. Sh[...]