Deutsch dropdown-ico

Moxa Technologies EIP3000 DF1 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Moxa Technologies EIP3000 DF1 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Moxa Technologies EIP3000 DF1, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Moxa Technologies EIP3000 DF1 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Moxa Technologies EIP3000 DF1. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Moxa Technologies EIP3000 DF1 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Moxa Technologies EIP3000 DF1
- Den Namen des Produzenten und das Produktionsjahr des Geräts Moxa Technologies EIP3000 DF1
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Moxa Technologies EIP3000 DF1
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Moxa Technologies EIP3000 DF1 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Moxa Technologies EIP3000 DF1 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Moxa Technologies finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Moxa Technologies EIP3000 DF1 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Moxa Technologies EIP3000 DF1, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Moxa Technologies EIP3000 DF1 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    MGate TM EIP3000 DF1 to EtherNet/IP Gateway User ’ s Manual First Edition, June 2009 www .moxa.com/product © 2009 Moxa Inc. All righ ts reserved. Reproducti o n without permi ssion is pr ohi bited.[...]

  • Seite 2

    MGate EIP3000 DF1 to EtherNet/IP Gateway User’s Manual The software d escribe d in t his m anual is fur ni shed u nder a l icense a greem ent an d m ay be use d onl y in ac corda nce with the terms of that agreement. Copyright Notice Copyright © 2009 Moxa Inc. All rights reserved. Reproducti o n without permi ssion is pr ohi bited. Trademarks MO[...]

  • Seite 3

    Table of Contents Chapter 1 Introduction ............................................................................................... 1-1 Overview .............................................................................................................................. 1 -2 Package Checklist ..................................................[...]

  • Seite 4

    Monitoring EtherNet/IP Activity ........................................................................................ 5-17 Open Traffic Monitor Win d ow ................................................................................... 5-18 Filter Traffic Information ..............................................................................[...]

  • Seite 5

    1 1 Chapter 1 Introduction W elcome to the MGate EIP3000 line of DF1 to EtherNet/IP gateways. All models feature easy protocol c onversion from DF1 to EtherNet/ IP , and RS-232/ 422 ports for D F1 communicat ion. One-port an d two-port models are available. This chapter is an introductio n to the MGate EIP3000 and includes the fo llowing sections: [...]

  • Seite 6

    MGate EIP3000 Series User ’ s Manual Introduction Overview The MGate EIP300 0 is a line of prot ocol gateways that provides users with y protocol conversion betwee n DF1 and Ethe rNet/IP y virtual serial port for multiple DF1 and EtherNet/IP device communicatio ns y W indows utilities for easy setup and traffic m onitoring. Protocol conversion be[...]

  • Seite 7

    MGate EIP3000 Series User ’ s Manual Introduction 1-3 Product Features y PCCC objects for Rockwell Automation networks supported. y 8 simult aneous EtherNet/IP clients with up t o 16 simulta neous requests per cl ient. y Serial redirector function provided. y ProCOM function provides virtual serial po rt for multiple DF1 and EtherNet/IP de vice c[...]

  • Seite 8

    2 2 Chapter 2 Getting Started This chapter provides basic inst ructions for install ing the MGate EIP3000 . The following topics are covered:  Connecting Power  Connecting Serial Devices  Connecting to a Host or the Network  Installing the Software  Mounting the Unit[...]

  • Seite 9

    MGate EIP3000 Series User ’ s Manual Getting St arted Connecting Power The unit can be powered using the AC adaptor or by connecting a power s ource to the term inal block, depending on the model. The following instructions are for the AC adaptor: 1. Plug the connector of the power adap ter into the DC-IN jack on the back of the unit. 2. Plug the[...]

  • Seite 10

    MGate EIP3000 Series User ’ s Manual Getting St arted 2-3 Installing the Software The W indows management utility is in stalled from the Document and Software CD. Follow the onscreen instructions after inserting the CD. Mounting the Unit The unit can b e mounted on the wall or mounted o n a DIN-Rail.[...]

  • Seite 11

    3 3 Chapter 3 Hardware: EIP3170, EIP3170I This chapter provides hardware information for the M Gate EIP3170 and E IP3170I. The following topics are covered:  Panel Layout  LED Indicators  Dimensions  Jumpers  Pin Assignments ¾ DB9 (Male) ¾ T erminal B lock (RS-422) ¾ Power Input, Relay Output  DIN-Rail, W all Mounting  Speci[...]

  • Seite 12

    MGate EIP3000 Series User ’ s Manual Hardware: EIP3170, EIP3170I Panel Layout LED Indicators Name Color Function PWR1 Red Power is being supplied to th e po wer input. PWR2 Red Power is being supplied to th e po wer input. Red St e a d y o n : Power is on and unit is bootin g up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server is not [...]

  • Seite 13

    MGate EIP3000 Series User ’ s Manual Hardware: EIP3170, EIP3170I Dimensions 20 mm (0.79 in) 69.5 mm (2.74 in) 25.9 mm (1.02 in) 35 mm (1.38 in) 20.6 mm (0.81 in) 29.91 mm (1.18 in) 1 1.5 mm (0.45 in) 124.5 mm (4.9 in) 1 18.5 mm (4.67 in) 89.2 mm (3.51 in) 14.5 mm (0.57 in) 29 mm (1.14 in) 14.5 mm (0.57 in) 3-3[...]

  • Seite 14

    MGate EIP3000 Series User ’ s Manual Hardware: EIP3170, EIP3170I Jumpers SW 1 The DIP switches are located be neath the DIP switch panel on the side of t he unit. T o add a 120 Ω termination resistor, set switch 3 to ON; set switch 3 to OFF (the default setting) to disable the ter mination resistor . T o set the pull high/low resistors to 150 K[...]

  • Seite 15

    MGate EIP3000 Series User ’ s Manual Hardware: EIP3170, EIP3170I Pin Assignments DB9 (Male) The MGate EIP3170 and EIP3170I use a DB9 (male) serial port f or RS-232 connection s to DF1 devices. 15 69 Pin RS-232 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 R TS 8 CTS Terminal Block (RS-422) The MGate EIP317 0 and EIP3170I use a terminal block c onnector f[...]

  • Seite 16

    MGate EIP3000 Series User ’ s Manual Hardware: EIP3170, EIP3170I Power Input, Relay Output V2+ V2- V1+ V1- Shielded Ground DC Power Input 1 DC Power Input 1 Relay Output Relay Output DC Power Input 2 DC Power Input 2 DIN-Rail, Wall Mounting There are tw o sliders on the back of the unit for DIN-Rail and wall m ounting. Mounting on a DI N-R ail : [...]

  • Seite 17

    MGate EIP3000 Series User ’ s Manual Hardware: EIP3170, EIP3170I 3-7 Specifications LAN Ethernet 10/100 M bps, RJ45, Auto MDI/MD IX Protection Built-in 1.5 KV magnetic isolation Serial Interface Interface RS-232/422 No. of Ports 1 port Connector T ype DB9 (mal e) for RS-232, term inal block for RS-422 RS-232: TxD, RxD, R TS, CT S, DTR, DSR, DCD, [...]

  • Seite 18

    4 4 Chapter 4 Hardware: EIP3270, EIP3270I This chapter provides hardware information for the M Gate EIP3270 and E IP3270I. The following topics are covered:  Panel Layout  LED Indicators  Dimensions  Jumpers  Pin Assignments ¾ DB9 (Male) ¾ Power Input, Relay Output  DIN-Rail, W all Mounting  Specifications[...]

  • Seite 19

    MGate EIP3000 Series User ’ s Manua l Hardware: EIP3270, EIP3270I Panel Layout LED Indicators Name Color Function PWR1 Red Power is being supplied to the po wer input. PWR2 Red Power is being supplied to the po wer input. Red St e a d y o n : Power is on and unit is bootin g up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server is not r[...]

  • Seite 20

    MGate EIP3000 Series User ’ s Manua l Hardware: EIP3270, EIP3270I Dimensions 20 mm (0.79 in) 69.5 mm (2.74 in) 25.9 mm (1.02 in) 35 mm (1.38 in) 20.6 mm (0.81 in) 29.91 mm (1.18 in) 1 1.5 mm (0.45 in) 124.5 mm (4.9 in) 1 18.5 mm (4.67 in) 89.2 mm (3.51 in) 14.5 mm (0.57 in) 29 mm (1.14 in) 14.5 mm (0.57 in) 4-3[...]

  • Seite 21

    MGate EIP3000 Series User ’ s Manua l Hardware: EIP3270, EIP3270I Jumpers SW 2 SW 1 The DIP switches are located be neath the DIP switch panel on the side of t he unit. T o add a 120 Ω termination resistor, set switch 3 on the port’ s assigned DIP switch to ON; set switch 3 t o OFF (the defaul t setting) to di sable the terminat ion resistor [...]

  • Seite 22

    MGate EIP3000 Series User ’ s Manua l Hardware: EIP3270, EIP3270I Pin Assignments DB9 (Male) The MGate EIP3000 uses DB9 (m ale) serial ports to connect Mod bus R TU or ASCII devices. Each port supports two serial interfaces: RS-232 and RS-422. 15 69 Pin RS-232 RS-422 1 DCD TxD- 2 RxD TxD+ 3 TxD RxD+ 4 DTR RxD- 5 GND GND 6 DSR --- 7 R TS --- 8 CTS[...]

  • Seite 23

    MGate EIP3000 Series User ’ s Manua l Hardware: EIP3270, EIP3270I DIN-Rail, Wall Mounting There are tw o sliders on the back of the unit for DIN-Rail and wall m ounting. Mounting on a DI N-R ail : Pull out the bottom slider; latch the unit onto the DIN-Rail, and push the slider back in. Mounting on the wall : Pull out both the top and bottom slid[...]

  • Seite 24

    MGate EIP3000 Series User ’ s Manua l Hardware: EIP3270, EIP3270I 4-7 Specifications LAN Ethernet 10/100 M bps, RJ45, Auto MDI/MD IX Protection Built-in 1.5 KV magnetic isolation Serial Interface Interface RS-232/422 No. of Ports 2 ports Connector T ype DB9 ( male) RS-232: TxD, RxD, R TS, CT S, DTR, DSR, DCD, GND Signals RS-422: Tx+, Tx-, Rx+, Rx[...]

  • Seite 25

    5 5 Chapter 5 Configuring the EtherNet/IP Gateway W e discuss the following topics in this chapter: S tarting MGate Manager tting ss ation nd Other Netw or k Set ti ngs cation Parame ters f Unit ctivity indow  Installing the Software  ¾ Change Language Se  Connecting to the Unit ¾ Broadcast Search ¾ Specify by IP Addre  Modifying the[...]

  • Seite 26

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway Installing the Software The following instructions explain how to install MGate Manager , a utility for configu ring and monitoring MGate EIP3000 units over the network. 1. Insert the D ocument and Software CD into the CD-ROM drive. Locate and run the following setup program[...]

  • Seite 27

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway 3. When the Select Destination Location window appears, click Next to co ntinue. Y ou m ay change the destinati on di rect o ry by fi rst clic ki ng o n Br owse.... 4. When the Select Add itional T ask s window ap pears, click Next to cont inue. Y ou may select Create a desk[...]

  • Seite 28

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway 5. Click Next to start copying the software files. 6. A progress bar will appear . The procedure should take only a few seconds to complete. 5-4[...]

  • Seite 29

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway 7. A message will indicate that MGate Manager is succ essfully installed. Y ou may choose to run it immediatel y by selecting Launch MG ate Manager . 8. Y ou may also open MGate Manager through St a r t Æ Programs Æ MG ate Manager Æ MGate Man ager , as shown below . 5-5[...]

  • Seite 30

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway Starting MGate Manager MGate Manager is a W indows-based u tility that is used to configure th e MGate EIP3000 . Before runni ng MGate Manager , make sure that your PC and the MGate EI P3000 are connected to the same network. Altern atively , the MGate EIP3 000 may be conn e[...]

  • Seite 31

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway A TTENTION Use “ Default Language ” before contactin g Moxa T echnical Support. W ith support for multiple languages, MGate Mana ger is more user -friendly and accessible. However , if you need assistance from Moxa T echnical Support , please change the la nguage to “D[...]

  • Seite 32

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway When the search is complete, every MGate EIP3000 that is found on the LAN will appear in the window with MAC address and IP address. Simply select the one that you wish to co nfigure. Specify by IP Address Click Specify by IP Addr ess if you know the IP address of the unit a[...]

  • Seite 33

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway If the search is successful, the unit will be listed in MGate Manager . Click the unit to begin configuration. A TTENTION If Sear ch by IP Address fails to locate the MGate EIP3000, the IP address that you entered might be incorrect. Tr y doing the search again and re-enter [...]

  • Seite 34

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway Configure IP Address and Other Network Settings The Network tab is w here the unit’ s network sett ings are configured. Y ou can modify the Name, Network Configuration, IP1 Address, IP2 Address (only for 2-port model) and the default IP1 address is 192.168.127.254, IP2 add[...]

  • Seite 35

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway Parameter Va l u e Notes Password (an alphanum eric string) Y ou can set a passw ord to prevent unauthori zed u sers fr om configuring the unit. The p assword will be required wh en anyone attempts to configure t he unit over the network. Modbus operatio n is not af fected b[...]

  • Seite 36

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway A TTENTION T o erase an existing pass word, leave both the New Password and Confirm Password text input boxes blank. The password will be erased when you click OK in the bottom right corner . Configure Serial Communication Parameters The Serial tab is where each s erial port[...]

  • Seite 37

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway Set up Routing and ProCOM function The definiti ons of the Routing tab determine how requ ests will be routed by the unit. How to set Routing on the MGate EIP3000 The MGate EIP3000 decides whe re to forward the recei ved requests according to its internal routing rules. The [...]

  • Seite 38

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway What is ProCOM? ProCOM is M oxa’ s proprietary function wh ich provides a vi rtual COM port for flexible DF1 and EtherNet/IP communication. This is an intelligent function of the Fieldbus gateway that translates the data to t he correct destination t hrough DF1 pr otocol. [...]

  • Seite 39

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway target DF1 device, it will forward the response to ProCOM and then the applicatio n running on your PC will receive the response. Set up Protocol Y ou can config ure the options f or DF1, Ether Net/IP , and CIP protocol. Res ponse T ime-out defines how much time the EIP3000 [...]

  • Seite 40

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway Set Up Miscellaneous This page de fines all other op tions that can not be cl assified. Currently , this page defines “ Auto Relay W arning ”, “ Rese t Button Pr otect ” and “ Te l n e t C o n s o l e ”. The auto relay warning includes power failure, Ethernet 1 o[...]

  • Seite 41

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway Verifying Location of Unit If you are m anaging multiple MGate units, you may wonder if you are configur ing the correct unit in MGate Manager . Y ou can select a unit in MGate Manager and click Locate to make that unit’ s “ Ready ” LED blink for a few seconds. This wi[...]

  • Seite 42

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway Open Traffic Monitor Window Select the unit that you wish to monitor and click Monitor to open the T raffic Monitor window . In the T raffic Monitor window , click St a r t to begin live monito ring of the data passing through t he selected MGate EIP3000 unit. 5-18[...]

  • Seite 43

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway T o stop capturing the log, press th e St o p button. Filter Traffic Information By default, all events are displayed in the traffic monitor window . MGate Manager also allows the data to be filtered so only the relev ant information is displayed. The filter is selected usin[...]

  • Seite 44

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway Save Log to File T o save the data log to a file, click Save . Y ou may retrieve a saved log by cl icking Load . Upgrading Firmware Firmware updates fo r the MG ate EIP3000 are located at www .moxa.com . After you have downloaded the new firmware onto your PC, you can use MG[...]

  • Seite 45

    MGate EIP3000 Series User ’ s Manual Configuring the EtherNet/IP Gateway The dialog boxes will guide yo u through the process. Y ou will need to browse your PC for the firmware file. Make sure that it matches your model. As the firmware is written to the unit, progress is displayed in the window . Once the firmware has been successf ully written [...]

  • Seite 46

    6 6 Chapter 6 Pin Assignments W e discuss the following topics in this chapter:  DB9 (Male )  T erminal Block (RS-422)  Power Input, Relay Output[...]

  • Seite 47

    MGate EIP3000 Series User ’ s Manual Pin Assignment s DB9 (Male) The MGate EIP3000 uses DB9 (m ale) serial ports to connect DF1 devices. Each por t su pports two serial interfaces: RS-232 and RS-422. 15 69 Pin RS-232 RS-422 1 DCD TxD- 2 RxD TxD+ 3 TxD RxD+ 4 DTR RxD- 5 GND GND 6 DSR --- 7 R TS --- 8 CTS --- EIP3170, EIP 31 70I Pin RS-232 1 DCD 2 [...]

  • Seite 48

    MGate EIP3000 Series User ’ s Manual Pin Assignment s Terminal Block (RS-422) The EIP3170 and EIP317 0I have a terminal block co nnector for RS-422 signal. Pin RS-422 1 TxD+ 2 TxD- 3 RxD+ 4 RxD- 5 GND Power Input, Relay Output V2+ V2- V1+ V1- Shielded Ground DC Power Input 1 DC Power Input 1 Relay Output Relay Output DC Power Input 2 DC Power Inp[...]