NEC MultiSync V323-2 Bedienungsanleitung

MultiSync V323-2 Lar ge Format Display User’ s Man ual[...]

Inde x DECLARA TION OF CONFORMITY ............................................................................................................. English-1 Important Information ................................................................................................................................... English-2 W ARNING .......................[...]

English-1 English DECLARA TION OF CONFORMITY This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U .S. Responsible P ar ty: NEC Di[...]

English-2 Impor tant Inf ormation TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT T O RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPT ACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULL Y INSER TED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOL T AGE COMPONENTS INSIDE. REFER SERVICING[...]

English-3 English FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MUL TI-FUNCTION MONITOR: • DO NOT OPEN THE MONITOR . There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualifi ed service personnel. • Do not[...]

English-4 Contents Y our new MultiSync monitor box* should contain the following: • LCD monitor • Power cord* 1 • V ideo Signal Cable • Wireless Remote Control and AA Batteries • Setup Manual • CD-ROM • Clamp x 1 • Screw with washer (M4 x 10) x 1 • W all Mount adapter x 4 • W all Mount adapter screw x 4 Power Cord* 1 Setup Manua[...]

English-5 English This de vice cannot be used or installed without the T abletop Stand or other mounting accessor y f or suppor t. For proper installation it is strongly recommended to use a trained, NEC authorized ser vice person. F ailure to f ollo w NEC standard mounting procedures could result in damage to the equipment or injur y to the user o[...]

English-6 Attaching Mounting Accessories The monitor is designed for use with the VESA mounting system. 1. Attach Mounting Accessories Be careful to avoid tipping monitor when attaching accessories. VESA Mounting Interface 200 mm 200 mm Mounting accessories can be attached with the monitor in the face down position. T o avoid damaging the screen fa[...]

English-7 English 4. Installing and removing optional tab le top stand CA UTION: Installing and removing the stand must be done by two or more people. T o install, follow those instructions included with the stand or mounting apparatus. Use only those devices recommended by the manufacturer . NO TE: Use ONL Y the thumbscrews which are included with[...]

English-8 P ar ts Name and Functions Contr ol P anel 쐃 PO WER button Switches the power on/off. See also page 16. 쐇 MUTE button Switches the audio mute ON/OFF . 쐋 INPUT button Acts as SET button within OSD menu. (T oggle switches between [DVI], [DPORT], [VGA], [HDMI], [DVD/HD], [SCART], [VIDEO] or [S-VIDEO]). These are available input only , [...]

English-9 English T erminal P anel From option control unit 쐃 A C IN connector Connects with the supplied power cord. 쐇 Main P ower Switc h On/Off switch to turn main power ON/OFF . 쐋 LAN port (RJ-45) LAN connection. See page 32. 쐏 RS-232C (D-Sub 9 pin) IN connector: Connect RS-232C input from external equipment such as a PC in order to con[...]

English-10 Wireless Remote Contr ol 쐃 PO WER button Switches the power on/standby . 쐇 INPUT button Selects input signal. DVI: DVI DISPLA YPORT : DPORT VGA: VGA HDMI: HDMI DVD/HD: DVD/HD, SCART VIDEO: VIDEO S-VIDEO: S-VIDEO OPTION: Depends on your connection 쐋 PICTURE MODE button Selects picture mode, [HIGHBRIGHT], [ST ANDARD], [sRGB], [CINEMA[...]

English-11 English Operating Range for the Remote Contr ol Point the top of the remote control toward the LCD monitor ’s remote sensor during button operation. Use the remote control within a distance of about 7 m (23 ft.) from remote control sensor or at a horizontal and vertical angle of within 30° within a distance of about 3.5 m (10 ft.). ?[...]

English-12 1. Determine the installation location CA UTION: Installing your LCD monitor must be done by a qualifi ed technician. Contact your dealer for more information. CA UTION: MOVING OR INST ALLING THE LCD MONIT OR MUST BE DONE BY TWO OR MORE PEOPLE. Failure to follow this caution may result in injury if the LCD monitor falls. CA UTION: Do no[...]

English-13 English 5. Switch on the power of all the attac hed external equipment When connected with a computer , switch on the power of the computer fi rst. 6. Operate the attached external equipment Display the signal from the desired input source. 7. Adjust the sound Make volume adjustments when required. 8. Adjust the screen (See pages 20 and[...]

English-14 Connections NO TE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. NO TE: Use an audio cable without a built-in resistor . Using an audio cable with a built-in resistor turns down the sound. Before making connections: * First turn off the power of[...]

English-15 English Connecting a P ersonal Computer Connecting your computer to your LCD monitor will enable you to display your computer ’s screen image. Some display cards with a pixel clock over 162MHz may not display an image correctly . Y our LCD monitor displays proper image by adjusting the factory preset timing signal automatically . <T[...]

English-16 Basic Operation P ower ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NO TE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button. Main Power Switch ON OFF Power Button Using the remot[...]

English-17 English Picture Aspect DVI, VGA, DPORT FULL 1:1 ZOOM NORMAL HDMI, DVD/HD, SCART , VIDEO, S-VIDEO FULL WIDE DYNAMIC 1:1 ZOOM NORMAL Aspect ratio of image Unchanged view* 3 Recommended selection for picture aspect* 3 4:3 NORMAL DYNAMIC Squeeze FULL Letterbox WIDE * 3 Grey areas indicate unused portions of the screen. NORMAL: Displays the a[...]

English-18 Inf ormation OSD The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc. Press the DISPLA Y button on the remote to bring up the Information OSD.  ID number assigned to current monitor* 1  ID number assigned monitor to be controlled via RS-232C* 2  Input Name  Audio input mode  Pictur[...]

English-19 English OSD (On-Screen-Displa y) Contr ols NO TE: Some functions may not be available depending on the model or optional equipment. PICTURE MODE Goto Adjustment S ele c t Return Clos e 70 50 50 50 50 50 THANK YOU FOR SA VING THE ENVIRONMENT . CARBON FOOTPRINT 86.0 % Input source Main Menu Icons Main Menu Item Sub Menu Key Guide Adjustmen[...]

English-20 Setting Default PICTURE BACKLIGHT Adjusts the overall image and background brightness. Press + or - to adjust. Note: When AMBIENT1 or AMBIENT2 is selected in picture mode, this function cannot be changed. Depends on destination CONTRAST Adjusts the image brightness in relationship to the input signal. Press + or - to adjust. Note: When s[...]

English-21 English H RESOLUTION VGA input only Adjusts the horizontal size of the image. - V RESOLUTION VGA input only Adjusts the vertical size of the image. - INPUT RESOLUTION VGA input only If there is a problem with signal detection, this function forces the monitor to display the signal at the desired resolution. After selection, execute “AU[...]

English-22 TIME Confi gures the time for the real-time clock. - DA YLIGHT SA VING Confi gures daylight savings on or of f. OFF RESET Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER, SCHEDULE SETTINGS and SCHEDULE LIST . - PIP* KEEP PIP MODE Allows the monitor to remain in “PIP” and “TEXT TICKER” m[...]

English-23 English INFORMA TION OSD Selects whether the information OSD is displayed or not. The information OSD will be displayed when the input signal or source changes. The information OSD will also give a warning when there is no-signal or the signal is out-of range. An interval between 3 to 10 seconds for the Information OSD to appear is avail[...]

English-24 TILE MA TRIX MEM When “INPUT” is selected, TILE MA TRIX setting is applied to each signal input. COMMON POWER ON DELA Y Adjusts the delay time between being in “standby” mode and entering “power on” mode. “POWER ON DELA Y” can be set between 0 and 50 seconds. 0 Sec. POWER INDICA TOR T urns ON or OFF the LED located at the[...]

English-25 English SCREEN SA VER Use the SCREEN SA VER function to reduce the risk of Image Persistence. GAMMA The display gamma is changed and fi xed when “ON” is selected. OFF BACKLIGHT The brightness of backlight is decreased when “ON” is selected. NOTE: Do not select this function when picture mode is AMBIENT1 or AMBIENT2. OFF MOTION T[...]

English-26 DEINTERLACE Selects the IP (Interlace to Progressive) conversion function. Note: For DVI input “DVI-HD” needs to be enabled in the DVI mode menu. ON ON Converts interlaced signals to progressive. This is the default setting. OFF Disables IP conversion. This setting is best suited for motion pictures, but increases the risk of image r[...]

English-27 English NO TE 1: CREA TING A SCHEDULE The schedule function allows the display to be set to power on and off at dif ferent times. Up to seven different schedules can be programmed. T o program the schedule: 1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET or the + button to enter the Se[...]

English-28 REMO TE CONTROL ID FUNCTION REMO TE CONTR OL ID The remote control can be used to control up to 100 individual MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors. For example: if there are many[...]

English-29 English 3. Press the “DISPLA Y” button on the remote control while aiming at the “PRIMAR Y” monitor . The Information OSD will be shown at top left side of the screen. Monitor ID: Displays the ID number of the current monitor within the daisy chain. T arget ID: Displays the ID number of the monitor that to be controlled via daisy[...]

English-30 This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. NO TE: When you use this function, EXTERNAL CONTROL should be “RS-232C” (See page 24). Functions that can be controlled by a personal computer are: • Power ON or OFF . • Switching between input signals. • Sound Mute ON or OFF . Connect[...]

English-31 English 2) Control command diagram For other commands, please see “External_Control.pdf” fi le on the CD-ROM. Function (Monitor ID = 1) Code Data Power ON 01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 31 03 73 0d Power OFF 01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 34 03 76 0d Input Source Select DisplayPort 01 30 41 30[...]

English-32 Connecting to a Netw ork Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function. NO TE: When you use this function, EXTERNAL CONTROL should be “LAN” (See page 24). T o use a LAN connection, you are required to assign an IP address. Example of LAN connection: Server Hu[...]

English-33 English Preparation Before Use Connect the monitor to a commercially available LAN cable before engaging in browser operations. Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting method. Although the type of proxy server will be a factor , it is possible that items [...]

English-34 Alert Mail Setting http://<the Monitor ’s IP address>/lanconfi g.html This option notifi es your computer of an error message via e-mail when using wired LAN. An error message notifi cation will be sent when an error occurs in the monitor . Alert Mail Checking [ENABLE] will turn on the Alert Mail feature. Checking [DISABLE] wi[...]

English-35 English Alert error message list Error n umber * ErrorCode Alert mail Message Explanation Measure 70h ~ 7Fh The monitor ’s power supply is not functioning normally . Standby power Abnormal Please contact your supplier . 80h ~ Fh The cooling fan has stopped. Cooling fan Abnormal Please contact your supplier . 90h ~ 9Fh The monitor ’s [...]

English-36 CRESTRON Setting Click “CRESTRON” on the left side of HOME. CRESTRON ROOMVIEW compatibility The monitor supports CRESTRON ROOMVIEW , allowing multiple devices connected in the network to be managed and controlled from a computer or a controller . For more information, visit http://www .crestron.com ROOMVIEW ROOMVIEW for managing from[...]

English-37 English Reduced Footprint: Provides the ideal solution for environments with superior image quality . Color Control Systems: Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards. OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control per[...]

English-38 No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Check the main Power Switch, it should be in the ON position. • Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode[...]

English-39 English Specifi cations Product Specifi cations LCD Module Pixel Pitch: Resolution: Color: Brightness: Contrast Ratio: Viewing Angle: 31.5”/801.3 mm diagonal 0.36375 mm 1920 x 1080 Over 16 million colors (depending on display card used) 450 cd/m 2 (Max.) @25°C 1300:1 89° (typ) @ CR>10 Frequency Horizontal: V ertical: 15.625/15.7[...]

English-40 1) Analog multi input (MiniDsub15p): VGA, DVD/HD, SCART , VIDEO, S-VIDEO Pin No Name 1 Red, DVD/HD_Pr , S-VIDEO_C 2 Green, DVD/HD_Y , S-VIDEO_Y , VIDEO 3 Blue, DVD/HD_Pb 4 GND 5 DDC-GND 6 Red-GND 7 Green-GND 8 Blue-GND 9 +5V (DDC) 10 SYNC-GND 11 SCART -SYNC 12 DDC-SDA 13 H-SYNC 14 V -SYNC 15 DDC-SCL 5 10 15 1 6 11 Mini D-SUB 15P 2) RS-23[...]

English-41 English NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly products, and always strive to help defi ne and comply with the latest independent[...]

English-42 WEEE Mark (Eur opean Directive 2012/19/EU) Within the Eur opean Union EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cable[...]