Nortel Networks TP-1610 SIP Bedienungsanleitung
- Schauen Sie die Anleitung online durch oderladen Sie diese herunter
- 280 Seiten
- 4.44 mb
Zur Seite of 280
Ähnliche Gebrauchsanleitungen
-
Network Router
Nortel Networks 2330
40 Seiten 1.38 mb -
Network Router
Nortel Networks Remote Gateway 50
260 Seiten 3.99 mb -
Network Router
Nortel Networks NN46120-104
300 Seiten 1.57 mb -
Network Router
Nortel Networks N300
72 Seiten 9.45 mb -
Network Router
Nortel Networks 9150
252 Seiten 2.56 mb -
Network Router
Nortel Networks 7.11
67 Seiten 1.09 mb -
Network Router
Nortel Networks 8600
62 Seiten 0.73 mb -
Network Router
Nortel Networks 1740
12 Seiten 0.44 mb
Richtige Gebrauchsanleitung
Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Nortel Networks TP-1610 SIP an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Nortel Networks TP-1610 SIP, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.
Was ist eine Gebrauchsanleitung?
Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Nortel Networks TP-1610 SIP die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.
Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Nortel Networks TP-1610 SIP. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.
Was sollte also eine ideale Gebrauchsanleitung beinhalten?
Die Gebrauchsanleitung Nortel Networks TP-1610 SIP sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Nortel Networks TP-1610 SIP
- Den Namen des Produzenten und das Produktionsjahr des Geräts Nortel Networks TP-1610 SIP
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Nortel Networks TP-1610 SIP
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen
Warum lesen wir keine Gebrauchsanleitungen?
Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Nortel Networks TP-1610 SIP zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Nortel Networks TP-1610 SIP und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Nortel Networks finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Nortel Networks TP-1610 SIP zu überspringen, wie es bei der Papierform passiert.
Warum sollte man Gebrauchsanleitungen lesen?
In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Nortel Networks TP-1610 SIP, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.
Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Nortel Networks TP-1610 SIP widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.
Inhaltsverzeichnis der Gebrauchsanleitungen
-
Seite 1
Mediant™ 2000 & TP-1610 SIP User’s Manual Version 4.4 Document #: LTRT-72504[...]
-
Seite 2
Notice This document describes the AudioCodes Median t™ 2000 SIP (Session I nitialization Protocol) gateway and the TP-1610 SIP cPCI board. Information contained in this document is believed to be accurat e and reliable at the time of printing. However, due to ongoin g product improvem ents and revisions, AudioCodes cannot guarant ee accuracy of [...]
-
Seite 3
Mediant 2000 SIP User’s Manual Contents Version 4.4 3 July 2005 Table of Contents 1 Overview ..................................................................................................................... 13 1.1 Available Conf igurat ions .......................................................................................................[...]
-
Seite 4
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 4 Document #: LTRT-72504 5.8.3.2 Numbering Plans and Type of Nu mber ...................................................................................... 48 5.8.4 Configuring the Ro uting Tables ........................................................................................... 49 5.8.4.1 [...]
-
Seite 5
Mediant 2000 SIP User’s Manual Contents Version 4.4 5 July 2005 8.4 Using IS DN NF AS ................................................................................................................ ........141 8.4.1 NFAS Interface ID .............................................................................................................1 41[...]
-
Seite 6
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 6 Document #: LTRT-72504 11.6.4.2 Configurati on via SNMP ......................................................................................................... .. 181 11.7 SNMP Manager Backwa rd Compat ibility...................................................................................... [...]
-
Seite 7
Mediant 2000 SIP User’s Manual Contents Version 4.4 7 July 2005 Appendix J SS7 Tunnelin g ........................................................................................... 231 J.1 MTP2 Tunneli ng Technol ogy ...................................................................................................... ..232 J.2 SS7 Characteristi[...]
-
Seite 8
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 8 Document #: LTRT-72504 List of Figures Figure 1-1: Typical Mediant 2000 Gateway Application .................................................................................. .1 4 Figure 2-1: Mediant 20 00 Front View .................................................................................[...]
-
Seite 9
Mediant 2000 SIP User’s Manual Contents Version 4.4 9 July 2005 Figure 8-3: SIP Call Fl ow Exam ple..................................................................................................... ............ 153 Figure 5-2: IP to Trunk Gr oup Routi ng Table ....................................................................................[...]
-
Seite 10
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 10 Document #: LTRT-72504 List of Tables Table 2-1: Mediant 2000 Front View Component De scriptio ns ........................................................................ 19 Table 2-2: Chassis LE D Indicators ........................................................................................[...]
-
Seite 11
Mediant 2000 SIP User’s Manual Contents Version 4.4 11 July 2005 Table K-5: VoiceXML Supported Pr operties ....................................................................................... ...........260 Table L-1: acBoardFat alError Alarm Trap ........................................................................................ ........[...]
-
Seite 12
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 12 Document #: LTRT-72504 Tip: When viewing this manual on CD, Web site or on any other electronic copy, all cross-references are h yperlinked. Click on the page or se ction numbers (shown in blue) to reach the individual cross-referenced item directly. To return back to the point from where you acc[...]
-
Seite 13
Mediant 2000 SIP User’s Manual 1. Overview Version 4.4 13 July 2005 1 Overview The Mediant 2000 SIP Voice over IP ( VoIP) gateway enables voice, fax, and data traffic to be sent over the same IP network. The Medi ant 2000 pr ovides ex cellent voice qual ity and optimized packet voice streaming over IP networks. The Mediant 2000 uses the award-win[...]
-
Seite 14
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 14 Document #: LTRT-72504 Figure 1-1 below illustrates typical Media nt 2000 gateway applications over VoIP Network. Figure 1-1: Typical Mediant 2000 Gate way Application SI P Se r v ic e N ode LAN PST N LAN T e le phone LAN SIP Pr o xy M e d ian t 2000 E 1 /T1 P R I/CAS Ro u t e r M e d ian t 2000 [...]
-
Seite 15
Mediant 2000 SIP User’s Manual 1. Overview Version 4.4 15 July 2005 • 48 Channels on 2 T1 spans with gate way-1 only • 96 Channels on 4 T1 spans with gate way-1 only • 192 Channels on 8 T1 spans with g ateway-1 only • 384 Channels on 16 T1 spans with gateway-1 and gateway-2 1.2 SIP Overview SIP is an application-layer control (signaling )[...]
-
Seite 16
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 16 Document #: LTRT-72504 1.3.3 PSTN-to-SIP Interworking The Mediant 2000 gateway performs int erworking between ISDN and CAS via E1/T1/J1 digita l spans and SIP IETF signaling protocol. 16 E1, T1 or J1 spans are supported (4 80 channels) in a two modules gateway. The Mediant 2000 gateway supports v[...]
-
Seite 17
Mediant 2000 SIP User’s Manual 1. Overview Version 4.4 17 July 2005 • Works with Proxy or without Proxy, using an internal routing table. • Fallback to internal routing table if Proxy is not respon ding. • Supports up to four Proxy serve rs. If the primary Prox y fails, the Mediant 200 0 automatically switches to a redundant Proxy. • Supp[...]
-
Seite 18
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 18 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 19
Mediant 2000 SIP User’s Manual 2. Mediant 2000 Physical Description Version 4.4 19 July 2005 2 Mediant 2000 Physical Description This section provides detailed info rmation on the Mediant 20 00 hardware components, th e location and functionality of the LEDs, buttons and connecto rs on the front and rear panels. 2.1 General The Mediant 2000 gatew[...]
-
Seite 20
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 20 Document #: LTRT-72504 2.2 The Mediant 2000 Chassis The Mediant 2000 chassis is an ind ustrial platform, 19” wide, 1U h igh and 12” deep that hou ses the TP-1610 board in its front cage , slot #1 (the lower slot) and the TP-1610 RTM in its rear cage, slot #1 (the lower slot). Slot # 2 in the [...]
-
Seite 21
Mediant 2000 SIP User’s Manual 2. Mediant 2000 Physical Description Version 4.4 21 July 2005 Figure 2-2: Front and Upper Vie w of the TP-1610 cPCI Board Table 2-3: Front and Upper Vie w of the TP-1610 cPCI Board Component Descriptions Item # Label Component Description 1 Status LEDs 2 ETH Ethernet LEDs 3 Reset button 4 cPCI LEDs 5 cPCI Latch 6 T1[...]
-
Seite 22
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 22 Document #: LTRT-72504 Note 1: Before removing or insertin g boards from / to the chassis, atta ch a wrist strap for electrostatic discharge (ESD) and connect it to the ra ck frame using a n alligator clip. Note 2: Do not set components down without protecting them with a static bag. 2.3.1.1 Remo[...]
-
Seite 23
Mediant 2000 SIP User’s Manual 2. Mediant 2000 Physical Description Version 4.4 23 July 2005 2.3.2 TP-1610 Front Panel LED Indicators The functionality of the front panel LEDs for the TP-1610 is described in the following four ta bles and illustrated in Figure 2-2 on page 21 . Note that there is a choice of front panels according to the number of[...]
-
Seite 24
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 24 Document #: LTRT-72504 2.4 Rear Transition Module The Mediant 2000 RTM includes a PST N trunks and an Ethernet interfaces. The Ethernet interface features dual 1 0/100 Base-TX, RJ-45 shielded conn ectors for (an ac tive / standby) redundancy sche me providing prot ection against the event of a fa[...]
-
Seite 25
Mediant 2000 SIP User’s Manual 2. Mediant 2000 Physical Description Version 4.4 25 July 2005 Figure 2-4: Rear Panel with 8 RJ-48c Connectors for 8 Trunks Table 2-9: Rear Panel with 8 RJ-48c Connect ors for 8 Trunks Componen t Descriptio ns Item # Label Component Description 1 ETHERNET 2 Ethernet Ports. 2 RJ-45 network conn ectors 2 TRUNKS 8 E1/T-[...]
-
Seite 26
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 26 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 27
Mediant 2000 SIP User’s Manual 3. Installing the Mediant 2000 Version 4.4 27 July 2005 3 Installing the Mediant 2000 This section describe s the hardware installation pro cedures for the Mediant 2000. For information on how to start using the gateway, refer to Section 4 on page 35 . For detailed information on the Mediant 2000 connectors, LEDs an[...]
-
Seite 28
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 28 Document #: LTRT-72504 Figure 3-1: 19-inch Rack & Desktop Acces sories 3.3 Mounting the Mediant 2000 The Mediant 2000 can be mounted on a desktop, or installe d in a stand ard 19-inch rack. Refer to Section 3.4 on page 30 for cabling the Mediant 2000. 3.3.1 Mounting the Mediant 2000 on a Desk[...]
-
Seite 29
Mediant 2000 SIP User’s Manual 3. Installing the Mediant 2000 Version 4.4 29 July 2005 Figure 3-2: Mediant 2000 Front Vie w with 19-inch Rack Mount Brackets Rack Mount Safety Instructions (UL) When installing the cha ssis in a ra ck, be sure to implem ent the followin g Safety instructions recommended by Underwriters Laboratories: • Elevated Op[...]
-
Seite 30
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 30 Document #: LTRT-72504 2. You’re now recommended to take the optional steps of fastening the device to the frame of the rack (as described above) while it is pl aced on the shelf, so preventing it from sliding when inserting cables into con nectors on the rear panel. 3.4 Cabling the Mediant 200[...]
-
Seite 31
Mediant 2000 SIP User’s Manual 3. Installing the Mediant 2000 Version 4.4 31 July 2005 Figure 3-4: Mediant 2000 Rear Panel Cabling (8 T runks, DC Po wer)) Table 3-2: Mediant 2000 Rear Panel Cabling (8 Tr unks, DC Power) Component Descrip tions Item # Label Component Description 1 RTM latches. 2 ETH A Category 5 network cable, conn ected to the Et[...]
-
Seite 32
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 32 Document #: LTRT-72504 3. Repeat steps 1 and 2 for the other Trunk cable but this time connect it to the connector labeled “Trunks 9 16”. The 50-pin male Telco cable connector must be wired accordi ng to the pinout in Table 3-3 belo w, and to mate with the female connector illustrate d in[...]
-
Seite 33
Mediant 2000 SIP User’s Manual 3. Installing the Mediant 2000 Version 4.4 33 July 2005 Figure 3-7: Pinout of RJ-45 Conn ectors 1 2 3 4 5 6 7 8 RJ-45 LAN Connect or and Pinout 4, 5, 7, 8 not connected 1 = Tx+ 2 = Tx- 3 = Rx+ 6 = Rx- 3.4.3 Connecting the Power Supply Connect the Mediant 2000 to the power sup ply using one of the following methods: [...]
-
Seite 34
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 34 Document #: LTRT-72504 Figure 3-8: DC Terminal Block Screw Connector When using a DC terminal block cr imp connector, take these 3 steps: 1. Remove the DC adaptor (screw connection type) that is attached to the Mediant 2000 rear panel. 2. Connec t the two insulated wires to the correct DC pow[...]
-
Seite 35
Mediant 2000 SIP User’s Manual 4. Getting Started Version 4.4 35 July 2005 4 Getting Started The Mediant 2000 is supplied with application softwar e already re sident in its flash memory (wi th factory default parameters). Section 4.1 below describes how to assign IP addres ses to the Mediant 2000, while Section 4.1.2 on page 35 describes how to [...]
-
Seite 36
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 36 Document #: LTRT-72504 correspond with your network IP settings. If your network doesn’t feature a default gateway, enter a dummy value in the ‘Default Gateway IP Address’ field. 5. Click the Reset button and click OK in the prompt; The Mediant 2000 applies the changes and restarts. This ta[...]
-
Seite 37
Mediant 2000 SIP User’s Manual 4. Getting Started Version 4.4 37 July 2005 This option is currently supported on one media gateway module (trunks 1 -8) only. To restore networking parameters to their initial state, take these 6 steps: 1. Disconnect the Mediant 2000 from the power and network cables. 2. Reconnect the power cable; the gateway i[...]
-
Seite 38
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 38 Document #: LTRT-72504 Enable the DMZ (Demilitarized Zone ) configuratio n on the resi dential route r for the LAN port where the Mediant 2000 gateway is conn ected. This enable s unknown packets to be routed to the DMZ port. 2. Under ‘SIP Parameters’, enter the Mediant 2000 domain name i[...]
-
Seite 39
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 39 July 2005 5 Web Management 5.1 Configuration Concepts Users can utilize the Mediant 2000 in a wide vari ety of applications, enabled by its parameters and configuration files (e.g., Call Progres s Tones (CPT), etc.). The param eters can be co nfigured and configuration files can be l[...]
-
Seite 40
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 40 Document #: LTRT-72504 5.4 Password Control The Embedded Web Serv er is protected by a unique usern ame and password combination. Th e first time a browser requ est is made, the User is req uested to provide hi s username an d password to obtain access. Subsequent reque sts are negotiated by the [...]
-
Seite 41
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 41 July 2005 5.6 Accessing the Embedded Web Server To access the Embedded Web Server, take these 4 steps: 1. Open a standard Web-browsing ap plication such as Microsoft™ Internet Explorer™ (Version 6.0 and higher) or Netscape™ Navig ator™ (Version 7.0 and higher). 2. In the [...]
-
Seite 42
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 42 Document #: LTRT-72504 5.7 Getting Acquainted with the Web Interface Figure 5-2 shows the general layout of the We b Interface screen. Figure 5-2: Mediant 2000 Web Interface The Web Interface screen features the fo llowing component s: • Title bar - contains three configurable elements : corpor[...]
-
Seite 43
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 43 July 2005 • Advanced Configuration – Use this menu to set the gateway’s advanced configuration parameters (for advance d users only) (refer to Section 5.9 on page 62 ). • Status & Diagnostics – Use thi s menu to view and monitor the gateway’s channels, Syslog messages[...]
-
Seite 44
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 44 Document #: LTRT-72504 5.8 Protocol Management Use this menu to configure the gateway’s SIP parameters an d tables. 5.8.1 Protocol Definition Parameters Use this submenu to configure the following ga teway’s specifi c SIP protocol parameters: • General Parameters • Proxy & Registratio[...]
-
Seite 45
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 45 July 2005 5.8.2 Advanced Parameters Use this submenu to configure the following gateway’s advance d control protocol parameters. • Disconnect and Answer Supervi sion • CDR and Debug • Miscellaneous Parameters • Supplementary Services 5.8.3 Number Manipulation Tables The VoI[...]
-
Seite 46
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 46 Document #: LTRT-72504 Figure 5-4: Source Phone Number Manipulation T able for Tel IP Calls 2. In the ‘Table Index’ drop-down list, select the r ange of entries that you want to edit (up to 20 entries can be configure d for Source Number Manipulation and 50 entrie s for Destination Number[...]
-
Seite 47
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 47 July 2005 Table 5-1: Number Manipulation Parameters Parameter Description Prefix / Suffix to add • Prefix - Enter the number / string yo u w ant to add to the front of the phone number. For example, if you enter 9 and the phone number is 123 4, the new number is 91234. • Suffix -[...]
-
Seite 48
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 48 Document #: LTRT-72504 • [2,3,4]xxx# represents four-digit numbers that start w i th 2, 3 or 4 • 54324 represents any number that sta rts with 54324 • 54324xx# represents a 7 digit number that starts with 54324 • 123[100-200]# rep resents all numbers from 123100 to 123200. The VoIP gatewa[...]
-
Seite 49
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 49 July 2005 5.8.4 Configuring the Routing Tables Use this submenu to conf igure the gateway’s IP Tel and Tel IP routing tables an d their associated parameters. 5.8.4.1 Tel to IP Routing Table The Tel to IP Routing Table is used to route incomi ng Tel call s to IP addresses. [...]
-
Seite 50
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 50 Document #: LTRT-72504 Alternative Routing’ table, the gateway imme diately initiates a call to the redu ndant destination using the next matched entry in the ‘Tel to IP Routing’ table. Note th at if a domain name in this table is resolved to two IP addresse s, the timeout for Invite retran[...]
-
Seite 51
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 51 July 2005 Table 5-3: Tel to IP Routing Table Parameter Description Any telephone number w hose destination number matches the prefi x defined in the ‘Desti nation Phone Prefix’ field and its source number matches the prefix defined in the adjac ent ‘Source Phone Prefix‘ field[...]
-
Seite 52
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 52 Document #: LTRT-72504 • You can configure the Trunk Group Se ttings t able to determine the method in which ne w calls are assigned t o channels within the trun k groups (a different method for ea ch trunk group can be config ured). For information on how to enable this o ption, refer to Secti[...]
-
Seite 53
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 53 July 2005 Table 5-4: IP to Trunk Group Routing Table Parameter Description Any SIP incoming call whose destination number matches t he prefix defined in the ‘Des tination Phone Prefix’ field and its source number matches the prefix defined in the adjacent ‘Source Pho ne Prefix?[...]
-
Seite 54
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 54 Document #: LTRT-72504 5.8.4.4 Reasons for Alternative Routing The Reasons for Alternative Routi ng screen includes two tables (T el IP and IP Tel). Ea ch table enables you to define up to 4 different release reaso ns. If a call is released as a result of one of these reasons, the gateway[...]
-
Seite 55
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 55 July 2005 5.8.5 Configuring the Profile Definitions Utilizing the Profiles feature, the M ediant 2000 pr ovides high-level adaptat ion when connected to a variety of equipment (from both Tel and IP side s) and proto cols, each of which require a different system behavior. Using Profi[...]
-
Seite 56
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 56 Document #: LTRT-72504 Note 2 : If not specified, the ptime gets a default value. Note 3 : The ptime specifies the maximum packeti zation time the gateway can receive. 5. Repeat steps 3 and 4 for the seco nd to fifth coders (optional). 6. Repeat steps 2 to 5 for the second to forth coder groups ([...]
-
Seite 57
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 57 July 2005 3. In the ‘Profile Preference’ drop-down list, select the preference (1-10) of the cu rrent Profile. The preference option is used to determi ne the priority of the Profile. If both IP and Tel profiles apply to the same call, the co ders an d other common para meters of[...]
-
Seite 58
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 58 Document #: LTRT-72504 2. In the ‘Profile ID’ drop-down list, select the IP Profile you want to edit (up to four IP Profiles can be configured). 3. In the ‘Profile Preference’ drop-down list, select the preference (1-10) of the cu rrent Profile. The preference option is used to determi ne[...]
-
Seite 59
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 59 July 2005 Table 5-5: Trunk Group Table Parameter Description Trunk ID The numbers (1-8) in the Trunk ID drop-do wn list represent the physical trunks on the ba ck of the VoIP gateway. Channels To enable the trunk’s B-ch annels, you must enter their number in this field. [n-m] repre[...]
-
Seite 60
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 60 Document #: LTRT-72504 5.8.7 Configuring the Trunk Group Settings The Trunk Group Settings Table is u sed to determi ne the method in which new calls are assigned to B-channels within each trunk group. If such a rule doesn’t exist (for a specifi c Trunk group), the global rule, defined by the C[...]
-
Seite 61
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 61 July 2005 Table 5-6: Channel Select Modes Mode Description By phone number Select the gateway port acco rding to the called number (ref er to the note below). Cyclic Ascending Select the next available channel i n an ascending cycle order. Always select the next higher channel n umbe[...]
-
Seite 62
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 62 Document #: LTRT-72504 5.9 Advanced Configuration Use this menu to set the gateway’s advanced configuration parameters (f or advanced users only). 5.9.1 Configuring the Network Settings From the Network Settings page you can define: • IP settings. • NTP settings. • Syslog settin gs. • S[...]
-
Seite 63
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 63 July 2005 5.9.1.1 Configuring the SNMP Managers Table The SNMP Managers table allows you to configur e the attributes of up to five SNMP managers. To configure the SNMP Managers Table, take these 6 steps: 1. Access the ‘Network Settings’ screen ( Advanced Configuration menu &[...]
-
Seite 64
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 64 Document #: LTRT-72504 maintenance, and debugging actions b ecome simp lified for the network ad ministrator. The NTP client follows a simple process in managing system time; the NTP client requests a n NTP update, receives an NTP response, and updates the l ocal system clock ba sed on a configur[...]
-
Seite 65
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 65 July 2005 5.9.2 Configuring the Channel Settings The Channels Settings screen enables you to set th e VoIP gateway channel parameters, su ch as Input and Output voice gain, Jitter buffer ch arac teristics, M odem, Fax and DTMF transport modes. These parameters are appli ed to all Med[...]
-
Seite 66
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 66 Document #: LTRT-72504 5.9.3 Configuring the Trunk Settings To configure the Trunk Settings, take these 9 steps: 1. Open the ‘Trunk Settings’ screen ( Advanced Config uration menu > Trunk Settings ); the ‘Trunk Settings’ screen is displayed. Initially, the screen appears with the p[...]
-
Seite 67
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 67 July 2005 Table 5-7: Trunks Status Color Indicator Keys Indicator Color Description Gray Disabled Green Active-OK Yellow RAI Alarm Red LOS Alarm Blue AIS Alarm Orange D-channel Alarm (ISDN only) 3. To modify the selected trunk’s parameters, click the Stop Trunk button; the trunk is[...]
-
Seite 68
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 68 Document #: LTRT-72504 Click the Close Windo w button. 7. After modifying the parameters: To apply the changes to the selected tru nk only, click the Apply Trunk Settings button. To apply the changes to all the trunks, click the Appl y to all Trunks button. The screen is refreshed, pa[...]
-
Seite 69
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 69 July 2005 5.9.5 Restoring and Backing up the Gateway Configuration The Configuration File screen enabl es you to restore (load a new ini file to the gateway) or to back up (make a copy of the VoIP gateway ini file and store it in a di rectory on your computer) the current configurati[...]
-
Seite 70
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 70 Document #: LTRT-72504 5.9.6 Regional Settings The ‘Regional Settings’ screen e nables you to set an d view the ga teway’s internal date and time and to load to the gate way the following configurat io n files: Call Prog ress Tones, CAS and Voice Prompts. For detailed information on the con[...]
-
Seite 71
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 71 July 2005 7. To save the loaded auxiliary files so they are available after a power fail, refer to Section 5.12 on page 84 . 8. To reset the Mediant 2000, refer to Section 5.12 on page 84 . 5.9.7 Changing the Mediant 2000 Username and Password To prevent unauthorized access to th e M[...]
-
Seite 72
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 72 Document #: LTRT-72504 Note: The information in columns ‘Quality Status’ and ‘Quality Info.’ (per IP address) is reset if two minutes elapse without a call to that destination. To view the IP connectivity information, take these 2 steps: 1. Set ‘AltRoutingTel2IPEnable’ to 1 or 2. [...]
-
Seite 73
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 73 July 2005 Table 5-8: IP Connectivity Parameters Column Name Description Quality Info. Displays QoS information: dela y and packet loss, calculated according to previo us calls. Note 1: This field is applicable only if the p arameter ‘AltRoutingTel2IPMode’ is set to 2 or 3. Note 2[...]
-
Seite 74
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 74 Document #: LTRT-72504 Table 5-9: Call Counters Description (continues o n pages 7 3 to 74) Counter Description Number of Established Calls This counter indicates the numbe r of estab lished calls. It is incremented as a result of one of the following release reasons, if the duration of the call [...]
-
Seite 75
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 75 July 2005 5.10.2 Monitoring the Mediant 2000 Trunks & Channels The Trunk & Channel Sta tus screen provides real time monito ring on the current status of the Mediant 2000 trunks & channels. To monitor the status of the trun ks and B-channels take this step: • Open t[...]
-
Seite 76
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 76 Document #: LTRT-72504 2. Click the submenu links to check/view a specific channel’s p arameter settings. Figure 5-26: Channel Status Details Screen 5.10.3 Activating the Internal Syslog Viewer The Message Log screen display s Syslog debug messages sent b y the gateway. Note that it is not reco[...]
-
Seite 77
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 77 July 2005 3. Select the messages, copy them and paste them into a text editor such as Notepad. Send this txt file to our Technical Support for diagnosis and troubleshooting. 4. To clear the screen of messages, click on the subm enu Message Log ; the screen is cleared and new messages[...]
-
Seite 78
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 78 Document #: LTRT-72504 5.11 Software Update Menu The ‘Software Update’ menu enables users to upgra de the Mediant 2000 software by loading a new cmp file along with the ini and a su ite of auxiliary files, or to update the existing auxiliary files. The ‘Software Update’ menu comprise s tw[...]
-
Seite 79
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 79 July 2005 Note: At this point, the process can be canceled with no conse quence to the Mediant 2000 (click the Cancel button). If you continue the process (by clicking t he Start Software Upgrade button, the process must be follo wed through and completed with a Mediant 2000 reset at[...]
-
Seite 80
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 80 Document #: LTRT-72504 Click Cancel ; the Mediant 2000 resets ut ilizing the cmp, ini and all other configuration files that were previously stored in flash me mory. Note that these are NOT the files you loaded in the previous Wizard steps. Click Back ; the ‘Load a cmp File’ screen is[...]
-
Seite 81
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 81 July 2005 Figure 5-33: Load a CPT File Screen 7. Follow the same procedure you followed when loading the ini file (refer to Step 6 ). The same procedure applies to the ‘Load a VP file’ (not applicab le to the Mediant 2000 gateway) screen and ‘Load a coefficient file’ screen. [...]
-
Seite 82
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 82 Document #: LTRT-72504 Figure 5-35: ‘End Process’ Screen 9. Click the End Process button; the ‘Quick Setup’ screen appears and the full Web application is reactivated. 5.11.2 Auxiliary Files The ‘Auxiliary Files’ screen enable s you to load to the gateway the follo wing files: CAS, Ca[...]
-
Seite 83
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 83 July 2005 Figure 5-36: Auxiliary Files Screen 2. Click the Browse button that is in the field for the type of file you want to load. 3. Navigate to the folder that contai ns the file you want to load. 4. Click the file and click the Open button; the name and path of the file appear i[...]
-
Seite 84
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 84 Document #: LTRT-72504 5.12 Save Configuration The Save Configuration screen enables users to save the current parameter configuration and the loaded auxiliary files to the non-volatile memory so they are available after a power fail. Parameters that are only save d to the volatile memory revert [...]
-
Seite 85
Mediant 2000 SIP User’s Manual 5. Web Management Version 4.4 85 July 2005 5.13 Resetting the Mediant 2000 The Reset screen enables you to remotely reset the gateway. Before reset you can choo se to save the gateway configuration to flash memory. To reset the Mediant 2000, take these 3 steps: 1. Click the Reset button on the main menu bar; the[...]
-
Seite 86
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 86 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 87
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 87 July 2005 6 ini File Configuration of the Mediant 2000 As an alternative to configuring th e VoIP gateway using the Web I nterface (refer to Section 5 on page 39 ), it can be configured by loading the ini file containing Customer-configured pa rameters. Th[...]
-
Seite 88
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 88 Document #: LTRT-72504 6.3 The ini File Content The ini file contains the following SIP gateway information: • Basic, Logging, Web and RA DIUS parameters shown in Table 6-1 on page 90 . • SNMP parameters shown in Table 6-2 on page 98 . • SIP Configuration parameters shown in Table 6-3 on pa[...]
-
Seite 89
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 89 July 2005 6.5 The ini File Example Figure 6-2 shows an example of an ini file for the VoIP gateway. Figure 6-2: SIP ini File Example PCMLawSelect = 1 ProtocolType = 1 TerminationSide = 0 FramingMethod = 0 LineCode = 2 TDMBusClockSource = 4 ClockMaster = 0 [...]
-
Seite 90
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 90 Document #: LTRT-72504 6.6 Basic, Logging, Web and RADIUS Parameters Note: In Table 6-1 , parameters in brackets are the format in the Embedded Web Server * . Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues o n pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range [...]
-
Seite 91
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 91 July 2005 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues o n pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription DNS2IP [Internal DNS Table] Internal DNS tabl e, used to resolve host names to IP addresses[...]
-
Seite 92
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 92 Document #: LTRT-72504 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues o n pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription BaseUDPport [RTP Base UDP Port] Lower boundary of UDP port used for RT P, RTCP (Real-Time Control Protocol) (RTP port +[...]
-
Seite 93
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 93 July 2005 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues o n pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription GwDebugLevel [Debug Level] Defines the S yslog logging level (usually set to 5 if debug tra[...]
-
Seite 94
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 94 Document #: LTRT-72504 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues o n pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription RAILowThreshold Low Threshold (in percentage ) that def ines the gateway‘s busy endpoints. The range is 0 to 100. The[...]
-
Seite 95
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 95 July 2005 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues o n pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription ResetWebPass word Allo w s resetting to default of Web password to: Username: “Admin” P[...]
-
Seite 96
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 96 Document #: LTRT-72504 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues o n pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription RA DIUSA uthPort [RADIUS Authentication Port] Port number of Authentication and Authorizat ion server. The default valu[...]
-
Seite 97
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 97 July 2005 Table 6-1: Basic, Logging, Web and RADIUS Para meters (continues o n pages 90 to 97) ini File Field Name Web Parameter Name * Valid Range and De scription BootPDelay The interval between the device’s startup and the first BootP/DHCP request tha[...]
-
Seite 98
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 98 Document #: LTRT-72504 6.7 SNMP Parameters Note: In Table 6-2 , parameters in brackets are the format in the Embedded Web Server * . Table 6-2: SNMP Parameter (continue s on pages 98 to 99) ini File Field Name Web Parameter Name * Valid Range and De scription DisableSNMP [Enable SNMP] 0 = SNMP is[...]
-
Seite 99
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 99 July 2005 Table 6-2: SNMP Parameter (continue s on pages 98 to 99) ini File Field Name Web Parameter Name * Valid Range and De scription SetCommunityString Note: Obsolete parameter, use SNMPReadWriteCommunityString_x instead. SNMP community string (up to 1[...]
-
Seite 100
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 100 Document #: LTRT-72504 6.8 SIP Configuration Parameters Note: In Table 6-3 , parameters in brackets are the format in the Embedded Web Server * . Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription Control[...]
-
Seite 101
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 101 July 2005 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription EnableProxySRVQuery [Enable Proxy SRV Queries] Enables the use of DNS Service Recor d (SRV) queries to[...]
-
Seite 102
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 102 Document #: LTRT-72504 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription ProxyRedundancy Mode [Redundancy Mode] 0 = Parking mode: gateway continues w orking wi th the last active Proxy until the next fai[...]
-
Seite 103
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 103 July 2005 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription Asserte dIdMode [Asserted Identity Mode] 0 = None (defa u lt). 1 = P-asserted. 2 = P-preferred. The As[...]
-
Seite 104
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 104 Document #: LTRT-72504 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription CoderName [Coders] CoderName = Coder,ptime (c an appear up to 5 times) The following coder names can be selected: g711Alaw64k – [...]
-
Seite 105
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 105 July 2005 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription AMRSendRat e Determines the selected rate for the AMR coder . T his parameter is relevant only if AMR [...]
-
Seite 106
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 106 Document #: LTRT-72504 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription CngDetectorMode [CNG Detector Mode] 0 = Don’t detect CNG (default) 2 = Detect CNG on caller side and start fax session (if IsFax[...]
-
Seite 107
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 107 July 2005 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription XferPrefix [Transfer Prefix] Defined string t hat is added, as a pref ix, to the transferred called nu[...]
-
Seite 108
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 108 Document #: LTRT-72504 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription OutOfBandDTMFFormat [Out-of-Band DTMF Format] The exact method to send out-of-band DT MF digits 1 = INFO format (Nortel) 2 = INFO [...]
-
Seite 109
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 109 July 2005 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription Profile Parameters CoderName_ID [Coder Group Settings] Coder list for Profiles (up to five coders in e[...]
-
Seite 110
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 110 Document #: LTRT-72504 Table 6-3: SIP Configuration Parameters (continues on pages 100 to 1 10) ini File Field Name Web Parameter Name * Valid Range and De scription IPProfile_ID [IP Profile Settings] IPProfile_<Profile ID> = <Profile Name>,< Preference>,<Coder Group ID>,[...]
-
Seite 111
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 111 July 2005 6.9 ISDN and CAS Interworking-Related Parameters Note: In Table 6-4 , parameters in brackets are the format in the Embedded Web Server * . Table 6-4: ISDN and CAS Inter working-Related Parameters (continues o n pages 111 to 114) ini File Field N[...]
-
Seite 112
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 112 Document #: LTRT-72504 Table 6-4: ISDN and CAS Inter working-Related Parameters (continues o n pages 111 to 114) ini File Field Name Web Parameter Name * Valid Range and De scription PlayRBTone2IP [Play Ringback Tone to IP] 0 = Ringback tone isn’t pla y ed (default). 1 = Ringback tone is playe[...]
-
Seite 113
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 113 July 2005 Table 6-4: ISDN and CAS Inter working-Related Parameters (continues o n pages 111 to 114) ini File Field Name Web Parameter Name * Valid Range and De scription PSTNAlertTimeout [PSTN Alert Timeout] Alert Timeout in seconds (ISDN T301 timer) for [...]
-
Seite 114
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 114 Document #: LTRT-72504 Table 6-4: ISDN and CAS Inter working-Related Parameters (continues o n pages 111 to 114) ini File Field Name Web Parameter Name * Valid Range and De scription CASTransportType [CAS Transport Type] 0 = Disable CAS relay (defa ult). 1 = Enable CAS relay mode u sing RFC 2833[...]
-
Seite 115
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 115 July 2005 6.10 Number Manipulation and Routing Parameters Note: In Table 6-5 , parameters in brackets are the format in the Embedded Web Server * . Table 6-5: Number Manipulation and Routing Parameter s (co ntinues on pages 115 to 121) ini File Field Name[...]
-
Seite 116
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 116 Document #: LTRT-72504 Table 6-5: Number Manipulation and Routing Parameter s (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription ChannelSelectMode [Channel Select Mode] Defines common rule of port allo cation for IP to TEL calls. • 0 = By pho[...]
-
Seite 117
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 117 July 2005 Table 6-5: Number Manipulation and Routing Parameter s (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription UseSourceNumber A sDisplay Name [Use Source Number as Display Name] 0 = Interworks the [...]
-
Seite 118
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 118 Document #: LTRT-72504 Table 6-5: Number Manipulation and Routing Parameter s (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription RouteModeTel2IP [Tel to IP routing Mode] 0 = Route calls before number manipulation (default) 1 = Route calls after[...]
-
Seite 119
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 119 July 2005 Table 6-5: Number Manipulation and Routing Parameter s (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription SourceNumberMapTel2IP [Source Phone Number Manipulation Tabl e for Tel IP calls] So[...]
-
Seite 120
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 120 Document #: LTRT-72504 Table 6-5: Number Manipulation and Routing Parameter s (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription For ETSI ISDN variant, the following Number Plan and Type co mbinations (Plan/T y pe) are supported in the Destinat[...]
-
Seite 121
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 121 July 2005 Table 6-5: Number Manipulation and Routing Parameter s (co ntinues on pages 115 to 121) ini File Field Name Web Parameter Name * Valid Range and De scription FilterCalls2IP [Filter Calls To IP] 0 = Disabled (default) 1 = Enabled If the filter ca[...]
-
Seite 122
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 122 Document #: LTRT-72504 6.11 E1/T1 Configuration Parameters Note: In Table 6-6 , parameters in brackets are the format in the Embedded Web Server * . Table 6-6: E1/T1/J1 Configuration Parameters (c ontinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription[...]
-
Seite 123
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 123 July 2005 Table 6-6: E1/T1/J1 Configuration Parameters (c ontinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription TerminationSide [ISDN Termination Side] Selects the ISDN termination side. A pplicable only to IS[...]
-
Seite 124
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 124 Document #: LTRT-72504 Table 6-6: E1/T1/J1 Configuration Parameters (c ontinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription ISDNNFASInterfaceID_x [NFAS Interface ID] Defines a different Interface ID for each T1 trunk. The valid range is 0 to 100. Th[...]
-
Seite 125
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 125 July 2005 Table 6-6: E1/T1/J1 Configuration Parameters (c ontinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription ISDNRxOverlap_x [Enable Receiving of Overlap Dialing] Enable / disable Rx ISDN over lap per trunk[...]
-
Seite 126
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 126 Document #: LTRT-72504 Table 6-6: E1/T1/J1 Configuration Parameters (c ontinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription ISDN Flexible Behavior Parame ters ISDN protocol is implemented in different S w itches / PBXs by different vendors. Several [...]
-
Seite 127
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 127 July 2005 Table 6-6: E1/T1/J1 Configuration Parameters (c ontinues on pages 122 to 127) ini File Field Name Web Parameter Name * Valid Range and De scription ISDNGeneralCCBehavior [General Call Control Behavior] 16 = The gateway clears down the call if it[...]
-
Seite 128
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 128 Document #: LTRT-72504 6.12 Channel Parameters The Channel Parameters d efine the DTMF, fax and modem t ransfer mode s. Refer to Appendix D on page 203 for a detailed description of Fax and Modem transfer mode s; refer to Section 8.2 on page 139 for detailed description on DTMF transport mode s.[...]
-
Seite 129
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 129 July 2005 Table 6-7: Channel Parameters (continues on pages 128 to 131) ini File Field Name Web Parameter Name * Valid Range and Description CNGDetectorMode [CNG Detector Mode] 0 = Disable (default). 1 = Event Only (N/A). 2 = Relay. T.38 fax relay session[...]
-
Seite 130
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 130 Document #: LTRT-72504 Table 6-7: Channel Parameters (continues on pages 128 to 131) ini File Field Name Web Parameter Name * Valid Range and Description V34ModemTransportTy pe [V.34 Modem Transport Type] V.34 Modem T ransport Type that the gateway uses. You can select: 0 = Transparent 2 = Modem[...]
-
Seite 131
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 131 July 2005 Table 6-7: Channel Parameters (continues on pages 128 to 131) ini File Field Name Web Parameter Name * Valid Range and Description RFC2833PayloadTy pe [RFC 2833 Payload T y pe] The RFC 2833 DTMF relay dynamic payload type. Range: 96 to 99, 106 t[...]
-
Seite 132
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 132 Document #: LTRT-72504 6.12.1 Dynamic Jitter Buffer Operation Voice frames are transmitte d at a fixed rate. If the frames arrive at the other end a t the same rate, voice quality is perceived as good. In many ca ses, however, some frames can a rrive slightly faster or slower than the other fram[...]
-
Seite 133
Mediant 2000 SIP User’s Manual 6. ini File Configuration of the Mediant 2000 Version 4.4 133 July 2005 6.13 Configuration Files Parameters The configuration files (Call Progress Tones, PR T, Voice P rompts and CAS) can be loaded t o the Mediant 2000 via the Embedded Web Server (refe r to Section 5.11.2 on page 82 ), or via TFTP session. To lo[...]
-
Seite 134
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 134 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 135
Mediant 2000 SIP User’s Manual 7. Configuration Files Version 4.4 135 July 2005 7 Configuration Files This section describes the configuration ( dat ) files that are load (in addition to the ini file) to the gateway. The configuration files are: • Call Progress Tones file (refer to Section 7.1 below). • Prerecorded Tones file (ref er to Secti[...]
-
Seite 136
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 136 Document #: LTRT-72504 • [CALL PROGRESS TONE #X] – containing the Xt h tone definition (starting f rom 1 and n ot exceeding the number of Call Progress Tones d efi ned in the first section) using the followi ng keys: Tone Type – Call Progress Tone type Figure 7-1: Call Progress Tone Ty[...]
-
Seite 137
Mediant 2000 SIP User’s Manual 7. Configuration Files Version 4.4 137 July 2005 7.2 Prerecorded Tones (PRT) File The Call Progress Tones mecha nism has several limitations, su ch as a limited number of predefined tones and a limited number of frequen cy integrations in one tone. To work around these limitations and provide ton e generation capabi[...]
-
Seite 138
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 138 Document #: LTRT-72504 When the list of recorded file s is converted to a single voiceprompts.dat file, every Voice Prom pt is tagged with an ID number, starting with “1”. This ID is u sed later by the Mediant 2000 to sta rt playing the correct announcement. Up to 1000 Voice Prompts can be u[...]
-
Seite 139
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 139 July 2005 8 Gateway Capabilities Description 8.1 Proxy or Registrar Registration Example REGISTER sip:servername SIP/2.0 VIA: SIP/2.0/UDP 212.179.22.229;branch=z9hG4bRaC7AU234 From: <sip:GWRegistrationName@sipgatewayname>;tag=1c29347 To: <sip:GWRegistratio[...]
-
Seite 140
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 140 Document #: LTRT-72504 8.3 ISDN Overlap Dialing Overlap dialing is a dialin g scheme used by severa l ISDN variants to send and / or receive calle d number digits one right aft er the other (or several at a time). As opposed to the en bloc dialing scheme in which a complete numbe r is sent. The [...]
-
Seite 141
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 141 July 2005 8.4 Using ISDN NFAS In regular (non-NFAS) T1 I SDN trunks, a single 6 4 kbps chann el carries sign aling for the other 2 3 B-channels of that particular T1 tru nk. This ch annel is calle d the D-channel and u sually resides on timeslot # 24. The ISDN Non-[...]
-
Seite 142
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 142 Document #: LTRT-72504 To define an explicit Interface I D for a T1 tr unk (t hat is different from the default), use the following parameters: • ISDNBehavior_x = 512 (x = 0 to 7 identi fying the Mediant 2000 physical trunk) • ISDNNFASInterfaceID_x = ID (x = 0 to 255) Note 1: Usually the Int[...]
-
Seite 143
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 143 July 2005 8.5 Configuring the DTMF Transport Types You can control the way DTMF digits are tran sporte d over the IP network to the remote endpoint. The following five modes are suppo rted: 1. Using INFO message according to the Nortel IETF draft: In this mode DTMF[...]
-
Seite 144
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 144 Document #: LTRT-72504 5. Sending DTMF digits (in RTP packets) as part of the audio stream (DTMF Rel ay is disabled): Note that this method is normally used with G.711 coders; with other Low Bit Rate (LBR) coders the quality of the DTMF digits is reduced. To set this mode: ‘IsDTMFUsed = 0?[...]
-
Seite 145
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 145 July 2005 Table 8-3: Summary of DTMF Configuration Param eters (continues on pag es 144 to 145) ini File Field Name [Web Name] Valid Range and Description RxDTMFOption Defines the supporte d Receive DTMF negotiation method. 0 = Don’t declare RFC 2833 T elephony-e[...]
-
Seite 146
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 146 Document #: LTRT-72504 8.6 Configuring the Gateway’s Alternative Routing (based on Connectivity and QoS) The Alternative Routing fe ature enables reli able routing of Tel t o IP calls when Proxy isn’t used. The Mediant 2000 gatewa y periodically chec ks the av ailability of connectivity and [...]
-
Seite 147
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 147 July 2005 8.6.4 Relevant Parameters The following parameters (descri bed in Table 6-5 ) are used to configure the Alternative Routing mechanism: • AltRoutingTel2IPEnable • AltRoutingTel2IPMode • IPConnQoSMaxAllowedPL • IPConnQoSMaxAllowedDelay 8.7 Working w[...]
-
Seite 148
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 148 Document #: LTRT-72504 In the transfer scenario there are three parties: Party A - transferring, Party B – tr ansferred, Party C – transferred to. • A Calls B. • B answers. • A presses the hookflash and puts B on-h old (party B hears a hold tone) • A dials C. • After A completed di[...]
-
Seite 149
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 149 July 2005 8.8 TDM Tunneling The Mediant 2000 TDM T unneling feature allows you to tunnel group s of digital trunk spans or timeslots (B-channels) ov er the IP network. TDM Tun neling utilizes the internal routing capabilities of the Mediant 2000 (working without Pr[...]
-
Seite 150
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 150 Document #: LTRT-72504 Figure 8-1: ini File Example for TDM Tunneling (Originating Side) EnableTDMOverIP = 1 ;E1_TRANSPARENT_31 ProtocolType_0 = 5 ProtocolType_1 = 5 ProtocolType_2 = 5 ProtocolType_3 = 5 prefix = '*,10.8.24.12' ;(IP address of the Mediant 2000 in the opposite location)[...]
-
Seite 151
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 151 July 2005 8.9 Call Detail Report The Call Detail Report (CDR) contains vital statistic information on calls made by the gateway. CDRs are generated at the end and (optionally) at the begin ning of each call (determined by the parameter ‘CDRReportL evel ’ ). The[...]
-
Seite 152
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 152 Document #: LTRT-72504 8.10 Trunk to Trunk Routing Example This example describes two Me diant 2000 gateways , each i nterface with the PSTN th rough four E1 spans. Gateway "A" is config ured to route all inco ming Tel IP calls to gateway "B". Gateway "B" genera[...]
-
Seite 153
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 153 July 2005 8.11 SIP Call Flow Example The Call Flow, shown in Figure 8-3 , describes SIP messages exchange d between Mediant 2000 gateway and an MP-108 gateway during a simple call. MP-108 with phone number “80 00”, calls Mediant 2000 with phone numbe r “1000?[...]
-
Seite 154
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 154 Document #: LTRT-72504 F2 10.8.201.10 ==> 10.8.201.108 Try ing SIP/2.0 100 Trying Via: SIP/2.0/UDP 10.8.201.108;branch=z9hG4bKacsiJkDGd From: <sip:8000@10.8.201.108>;tag=1c5354 To: <sip:1000@10.8.201.10> Call-ID: 534366556655skKw-8000--1000@10.8.201.108 Server: Audiocodes-Sip-Gate[...]
-
Seite 155
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 155 July 2005 CSeq: 18153 ACK Supported: 100rel,em Content-Length: 0 Note: Phone "8000" goes on-hook; gateway 10.8.201.108 sends "BYE" to gateway 10.8.201.10. Voice path is established. F6 10.8.201.108 ==> 10.8.201.10 BYE BYE sip:1000@10.8.201.10[...]
-
Seite 156
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 156 Document #: LTRT-72504 8.12 SIP Authentication Example Mediant 2000 gateway supports basic and dig est authentication types, according to SIP RFC 3261 standard. A proxy server mi ght require au thentication before forwarding a n INVITE message. A Registrar/Pro xy server may also require authenti[...]
-
Seite 157
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 157 July 2005 Using SIP protocol “sip” Proxy IP from ini file “10.2.2.222” The equation to be evaluated: “REGISTER:sip:10.2.2.222”. The MD5 algorithm is run on this equati on and stored for future usage. The result is:”a9a031 cfddcb10d91c8e7 b4926086f7e?[...]
-
Seite 158
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 158 Document #: LTRT-72504 8.13 Nortel IMS Specific Features and Configuration 8.13.1 SIP2PRI Gateway To enable Nortel’s IMS SIP2PRI gateway specific features, add the following parameters to the ini file: ApplicationProfile = 4444 IsProxyUsed = 1 SendInviteToProxy = 1 ProxyIP = <Proxy IP a[...]
-
Seite 159
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 159 July 2005 For the SIP2PRI gateway to be able to apply the ro uting rule s on the combine d string, the prefix (domain name and tru nk group) must previously be defined in t he IP to Trunk Group Routing table either using the Embedded Web Server (refer to screen bel[...]
-
Seite 160
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 160 Document #: LTRT-72504 Note: Usually each E1/T1 span is c onfigured as a separate trun k group. Different Domain names, according to the originat ed trunk group (or E1/T1 spans), ca n be determined via the Tel to IP Routing table. To enable different domain names add th e following parameters to[...]
-
Seite 161
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 161 July 2005 2. Use the number manipulation table (exemplified below) to assign NPI/TON val ues according to the number’s prefix: NumberMapIP2TEL= nortelnetworks.com/TrunkGroup3,30,$$,$$,1,2 In the above example, all numbers starting with t he ‘nortelnetworks.co m[...]
-
Seite 162
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 162 Document #: LTRT-72504 8.13.2 SIP2CAS (Call Pilot) Gateway To enable SIP2CAS gateway specifi c features, take these 2 steps: 1. Add the following parameters to the ini file: ApplicationProfile=1 IsProxyUsed = 1 SendInviteToProxy = 1 ProxyIP = <Proxy IP address> EnableHold = 1 EnableTra[...]
-
Seite 163
Mediant 2000 SIP User’s Manual 8. Gateway Capabilities Description Version 4.4 163 July 2005 • If the call transfer fails, the gateway either plays a busy tone (if the de stination client to who m the call is transferred is b usy) or it plays a reorder tone (for all other reasons). The tone i s played for 10 seconds (TimeForRe orderTone=10) to [...]
-
Seite 164
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 164 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 165
Mediant 2000 SIP User’s Manual 9. Diagnostics Version 4.4 165 July 2005 9 Diagnostics Several diagnostic tool s are provided, enabling you to identify co rrect functioning of the Me diant 2000, or an error condition with a probable cause and a solution or workaro und. • Front panel indicator LEDs on the Mediant 2000. The location and functional[...]
-
Seite 166
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 166 Document #: LTRT-72504 9.2.1 Syslog Servers Users can use the provided Syslog serv er (ACSyslog08.exe) or other third-part y Syslog servers. Examples of Syslog serv ers available as sharew are on the Internet: • Kiwi Enterprises: http://www.kiwisyslog.com/ • The US CMS Server: http://uscms.f[...]
-
Seite 167
Mediant 2000 SIP User’s Manual 10. BootP/DHCP Support Version 4.4 167 July 2005 10 BootP/DHCP Support 10.1 Startup Process The startup proces s (illustrated in Figure 10-1 on page 168 ) begins when the gateway is reset (physically or from the We b / SNMP) and end s when the operational software is running. I n the startup process, the netwo rk pa[...]
-
Seite 168
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 168 Document #: LTRT-72504 Figure 10-1: Mediant 2000 Startup Process DHCP x tim es BootP/DHCP reply contains firmware file name ? Download firmware via TFTP BootP/DHCP reply contains ini file name? Download configuration files via TFTP Run operational software No No Update network parameters from Bo[...]
-
Seite 169
Mediant 2000 SIP User’s Manual 10. BootP/DHCP Support Version 4.4 169 July 2005 10.2 DHCP Support When the gateway is configured to use DHCP (DHCPEnabl e = 1), it attempts to contact the enterprise’s DHCP server to obtain the networki ng param eters (IP address, subnet mask, def ault gateway, primary/secondary DNS server and SI P server addr es[...]
-
Seite 170
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 170 Document #: LTRT-72504 • From version 4.4 to version 4.4 or to any highe r versi on, the device retains its configuration ( ini file), however, the auxiliary file s (CPT, logo, etc.) may be erased. When using the Software Upgrad e wizard, available through the Web Interface (refer to Section 5[...]
-
Seite 171
Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 171 July 2005 11 SNMP-Based Management Simple Network Manage ment Protocol (SNMP) is a stan dard-based network control p rotocol used to manage element s in a network. The SN MP Manager (usua lly implemented by a Net work Manager (NM) or an Element Ma nager (EM)) co nnect s to a[...]
-
Seite 172
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 172 Document #: LTRT-72504 • Trap Message - The SNM P standard furnishes a m echanism by which devi ces can ‘reach out’ to a Network Manager on their own (via a ‘t rap’ message) to notify or alert the manager of a problem with the device. This typically req uires each device on the network[...]
-
Seite 173
Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 173 July 2005 11.2 Carrier Grade Alarm System The basic alarm system has been extended to a carri er-grade alarm system. A carrie r-grade alarm system provide s a reliable al arm report ing me chanism that takes into account EMS outages, network outages , and transport mechanism[...]
-
Seite 174
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 174 Document #: LTRT-72504 11.4 Third-Party Performance Monitoring Measurements Performance measurements are avail able for a third-party performa nce monitoring system through an SNMP interfa ce. These measurem ents can be p olled at scheduled inte rvals by an external poller or utility in a media [...]
-
Seite 175
Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 175 July 2005 Note: The acBoard MIB is still supported but is being replaced by five newer proprietary MIBs. The acBoard MIB has the following groups: boardConfiguration boardInformation channelConfiguratio n channelStatus reset acTrap As noted above, fiv[...]
-
Seite 176
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 176 Document #: LTRT-72504 acAlarmVarbinds and also in acBoar d.acTrap. acBoardTrapDefinitions. oid_1_3_6_1_4_1_500 3_9_10_1_21_2_ 0). The table size can be altered via notificationLogMIB.notificati onLogMIBObjects.nlmConfig.nlmCo nfigGlobalEntryLimit or notificationLogMIB.notificationLogMIBOb jects[...]
-
Seite 177
Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 177 July 2005 11.6 SNMP Interface Details This section describes det ails of the SNMP inte rfa ce that is required when developing an Ele ment Manager (EM) for any of th e TrunkPack-VoP Series products, or to manage a device with a MIB browser. Currently, both SNMP and ini file [...]
-
Seite 178
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 178 Document #: LTRT-72504 To change the only r ead-write community string from v2admin to v2mgr, take these 4 steps: 1. Follow the procedure above to add a read-write com munity string to a row for v2mgr. 2. Set up the EM so that subsequent ‘set’ requ ests use the new community string, v2mg[...]
-
Seite 179
Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 179 July 2005 1. Add a row to the snmpTargetAddrTable with these values: Name=mgr0, TagList =MGR, Params= v2cparams. 2. Add a row to the tgtAddressMaskTable table with these values: Name=m gr0, tgtAddressMask=255.255. 255.255:0. The agent does not allow creation of a ro w in thi[...]
-
Seite 180
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 180 Document #: LTRT-72504 11.6.4 Multiple SNMP Trap Destinations An agent can now send traps to up to five managers. For ea ch manager, set the followin g parameters defined in the snmpMan agersTable in the acBoardMIB: • snmpTrapManagerSen ding • snmpManagerIsUsed • snmpManagerTrapPort • sn[...]
-
Seite 181
Mediant 2000 SIP User’s Manual 11. SNMP-Based Management Version 4.4 181 July 2005 Figure 11-1: Example of Entries in a Dev ice ini file Regarding SNMP ; SNMP trap destinations ; The board maintains a table of trap destinations containing 5 ;rows. The rows are numbered 0..4. Each block of 4 items below ;apply to a row in the table. ; To configure[...]
-
Seite 182
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 182 Document #: LTRT-72504 To disable a trap destination: • Change TagList on the approp riate row in the snmpTargetAdd rTable to the empty string. To enable a trap destination: • Change TagList on the approp riate row in the snmpTargetAdd rTable to ‘AC_TRAP’. 11.7 SNMP Manager Backw[...]
-
Seite 183
Mediant 2000 SIP User’s Manual 12. Selected Technical Specifications Version 4.4 183 July 2005 12 Selected Technical Specifications Table 12-1: Mediant 2000 Selected T echnical Specifications (continues on pages 1 83 to 185) Function Specification Trunk & Channel Capacity 1 Capacity w i th E1 1, 2, 4, 8 or 16 E1 spans, 30, 60, 120, 240 or 480[...]
-
Seite 184
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 184 Document #: LTRT-72504 Table 12-1: Mediant 2000 Selected T echnical Specifications (continues on pages 1 83 to 185) Function Specification Fax Transpar en cy Automatic fax bypass (pass-through) to G.711, ADPCM or NSE b y pass mode Modem Transparen c y Automatic switching (pass-through) to PC M, [...]
-
Seite 185
Mediant 2000 SIP User’s Manual 12. Selected Technical Specifications Version 4.4 185 July 2005 Table 12-1: Mediant 2000 Selected T echnical Specifications (continues on pages 1 83 to 185) Function Specification Environmental (AC) Operation Temp: 0° to 40° C / 32° to 104° F Storage: -40° to 70° C / -40° to 158° F Humidity: 10 to 90% non-co[...]
-
Seite 186
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 186 Document #: LTRT-72504 Reader's Notes[...]
-
Seite 187
Mediant 2000 SIP User’s Manual A. Mediant 2000 SIP Software Kit Version 4.4 187 July 2005 Appendix A Mediant 2000 SIP Sof tware Kit Table A-1 describes the stand ard supplied softwar e kit for Mediant 2000 SIP gateway s. The supplied documentation include s this User’s Manual, the Mediant 2000 Fast Track and the Mediant 2000 & TP-1610 SIP R[...]
-
Seite 188
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 188 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 189
Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 189 July 2005 Appendix B The BootP/TFTP Configuration Utility The BootP/TFTP utility enables you to easily co nfigure and provision our boards and media gateways. Similar to third-party BootP/TFTP utilities (which are al so supported) but with added functionality; [...]
-
Seite 190
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 190 Document #: LTRT-72504 • Protection against entering faulty information. • Rem ote res et. • Unicast BootP response. • User-initiated BootP respond, for remote provisioning over WA N. • Filtered display of BootP requests. • Location of other BootP utilities t hat contain the same MAC[...]
-
Seite 191
Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 191 July 2005 B.7 BootP/TFTP Application User Interface Figure B-1 shows the main application sc reen for the BootP/TFTP utility. Figure B-1: Main Screen B.8 Function Buttons on the Main Screen Pause: Click this button to pause the BootP Tool so that no repli es ar[...]
-
Seite 192
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 192 Document #: LTRT-72504 When a gateway resets, it first sends a BootRe quest. Therefore, Re set can be used to force a BootP session with a gateway without needing to powe r cycle the gateway. A s with any BootP session, the comp uter running the Boot P Tool must be located on the same subnet as [...]
-
Seite 193
Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 193 July 2005 B.10 Setting the Preferences The Preferences windo w, Figure B-3 , is used to configure the BootP Tool parameters. Figure B-3: Preferences Screen B.10.1 BootP Preferences ARP is a common acronym for Address Resoluti on Protocol, and is the method u se[...]
-
Seite 194
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 194 Document #: LTRT-72504 • ARP Type: The type of entry made into the ARP cache on the computer, once ARP Manipulation is enabled, can be eithe r Dy nam ic or Static . Dynamic entries expire after a period of time, keeping the cache clean so t hat stale entri es do not consume co mputer resources[...]
-
Seite 195
Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 195 July 2005 B.11 Configuring the BootP Clients The Clients window, shown in Figure B-4 below, is used to set up th e parameters for each specific VoIP gateway. Figure B-4: Client Configuration Screen B.11.1 Adding Clients Adding a client creates an entry in the B[...]
-
Seite 196
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 196 Document #: LTRT-72504 To add a client to the list using a template, take these 5 steps: 1. Click on the Add New Client Icon; a client with blank parameters i s displayed. 2. In the field Template , located on the right side of the Client Configuration Windo w , click on the down arrow to th[...]
-
Seite 197
Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 197 July 2005 B.11.5 Setting Client Parameters Client parameters are liste d on the right side of the Client Configuration Window . • Client MAC: The Client MAC is used by BootP to identify the VoIP gateway. The MAC address for the VoIP gateway is printed on a la[...]
-
Seite 198
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 198 Document #: LTRT-72504 • Call Agent: This field spe cifies the IP address of the MGCP Call Agent that is controlling the gateway. This field can be ignored for all other control /signaling prot ocols. B.11.6 Using Command Line Switches You can add command line swit ches in the field Boot File [...]
-
Seite 199
Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility Version 4.4 199 July 2005 B.12 Managing Client Templates Templates can be used to simplify configuratio n of clients when most of the parameters are the same. Figure B-5: Templates Screen To create a new template, take these 4 steps: 1. Click on the Add New Template button[...]
-
Seite 200
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 200 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 201
Mediant 2000 SIP User’s Manual C. RTP/RTCP Payload Types and Port Allocation Version 4.4 201 July 2005 Appendix C RTP/RTCP P ayload T ypes and Port Allocation RTP Payload Types are defined in RF C 1889 and RFC 189 0. We have added new payload types to enable advanced use of other coder types. These types a re report edly not used by other applica[...]
-
Seite 202
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 202 Document #: LTRT-72504 Payload Ty pe Description Basic Packet Rate [msec] 53 NetCoder 8.0 kbps 20 54 NetCoder 8.8 kbps 20 55 NetCoder 9.6 kbps 20 56 Transparent PCM 20 96 DT MF relay per RFC 2833 102 Fax Bypass 20 103 Modem Bypass 20 104 RFC 2198 (Re dundancy) Same as chan nel’s voice coder. 1[...]
-
Seite 203
Mediant 2000 SIP User’s Manual D. Fax and Modem Transport Mode s Version 4.4 203 July 2005 Appendix D Fax and Modem T ransport Modes D.1 Fax/Modem Settings Users can choose to use f or fax, and for each m odem type (V.22/V.23/Bell/V.32/V.34), one of the following transport methods: • Fax relay mode (demodulation / remodul ation, not applicable [...]
-
Seite 204
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 204 Document #: LTRT-72504 D.1.3 Supporting V.34 Faxes V.34 fax machine support is available only in by pa ss mode (fax relay is not su pported) when the channel is configured in on e of the configurations described bel ow: FaxTransportMode = 2 (Bypass) V34ModemTransportType = 2 (Modem bypass) In th[...]
-
Seite 205
Mediant 2000 SIP User’s Manual E. Mediant 2000 Clock Settings Version 4.4 205 July 2005 Appendix E Mediant 2000 Clock Settings The gateway can either ge nerate its own timing si gnal s, using an internal clock, or recover them from one of the E1/T1 trunks. a . To use the internal gateway clock source config ure the following parameters: • TDMBu[...]
-
Seite 206
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 206 Document #: LTRT-72504 Reader's Notes[...]
-
Seite 207
Mediant 2000 SIP User’s Manual F. Cu stomizing the Mediant 2000 Web Interface Version 4.4 207 July 2005 Appendix F Customizing the Mediant 2000 W eb Interface Customers incorporating the Me diant 2000 into thei r portfolios can customize the device’s Web Interface to suit their specific corp orate logo an d product naming conventions. Customers[...]
-
Seite 208
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 208 Document #: LTRT-72504 2. In the URL field, append the suffix ‘AdminPage’ (note that it’s case-sensitive) to the IP address, e.g., http://10.1.229.17/AdminPage. 3. Click Image Load to Device ; the Image Download screen is displayed (shown in Figure F-3 ). Figure F-3: Image Download Screen [...]
-
Seite 209
Mediant 2000 SIP User’s Manual F. Cu stomizing the Mediant 2000 Web Interface Version 4.4 209 July 2005 Table F-1: Cu stomizable Logo ini File Parameters Parameter Description LogoFileName The name of the image f ile contain ing your corporate logo. Use a gif, jpg or jpeg image fil e . The default is AudioCodes ’ logo file. Note: The length of [...]
-
Seite 210
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 210 Document #: LTRT-72504 6. To save the image to flash memory so it is available after a power fail, refer to Section 5.12 on page 84 . The new background appe ars on all Web Interface screens. Tip 1: If you encounter any problem during the loading of the files, or y ou want to restore the default[...]
-
Seite 211
Mediant 2000 SIP User’s Manual F. Cu stomizing the Mediant 2000 Web Interface Version 4.4 211 July 2005 F.4 Modifying ini File Parameters via the Web AdminPage To modify ini file parameters via the Ad minPage, take these 6 steps: 1. Access the Mediant 2000 Embedded Web Server (refer to Section 5.6 on page 41 ). 2. In the URL field, append the[...]
-
Seite 212
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 212 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 213
Mediant 2000 SIP User’s Manual G. Accessory Programs a nd Tools Version 4.4 213 July 2005 Appendix G Accessory Programs and T ool s The accessory applicatio ns and tools shipped with th e device provide you with friendly interfa ces that enhance device usab ility and smooth your tr ansition to the new VoIP infrastructure. The following applicatio[...]
-
Seite 214
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 214 Document #: LTRT-72504 G.1.1 Converting a CPT ini File to a Binary dat File For detailed information on creatin g a CPT ini file, refer to Section 7.1 on page 135 . To convert a CPT ini file to a binary dat file, take these 10 steps: 1. Execute the TrunkPack Downloadable Conversi on Utility,[...]
-
Seite 215
Mediant 2000 SIP User’s Manual G. Accessory Programs a nd Tools Version 4.4 215 July 2005 G.1.2 Creating a Loadable Voice Prompts File For detailed information on the Voic e Prompts file, ref er to Section 7.2 on page 137 . To create a loadable Voice Prompts dat file from your voice recording files, take these 7 steps: 1. Execute the TrunkPac[...]
-
Seite 216
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 216 Document #: LTRT-72504 4. Arrange the files according to your require ments by dragging and dr opping them from one location in the list to another. Note that the sequence of the files determines their assigne d Voice Prompt ID. Tip 1: Use the Play button to play wav files through your PC speake[...]
-
Seite 217
Mediant 2000 SIP User’s Manual G. Accessory Programs a nd Tools Version 4.4 217 July 2005 G.1.3 Encoding / Decoding an ini File For detailed information on secure d ini file, refer to Section 6.1 on page 87 . To encode an ini file, take these 6 steps: 1. Execute the TrunkPack Downloadable Conversi on Utility, DConvert240.exe (su pplied with t[...]
-
Seite 218
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 218 Document #: LTRT-72504 G.1.4 Creating a Loadable Prerecorded Tones File For detailed information on the PRT file, refer to Section 7.2 on page 137 . To create a loadable PRT dat file from your raw da ta files, take these 7 steps: 1. Prepare the prerecorded tones (raw data PCM or L8) files yo[...]
-
Seite 219
Mediant 2000 SIP User’s Manual G. Accessory Programs a nd Tools Version 4.4 219 July 2005 Click the Add File(s) butto n; the ‘Select Files’ screen opens. Select the requi red Prerecorded Tone files a nd press the Add>> button. Close the ‘Select Files’ screen. 5. For each raw data file, define a Tone Type, a Coder and a Defa ult [...]
-
Seite 220
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 220 Document #: LTRT-72504 G.2 PSTN Trace Utility These utilities are designed to convert PSTN trace binary files to textual form. The binary PSTN trace files are generated when the User se ts the PSTN interfa ce to trace mode. G.2.1 Operation Generating textual trace/audit file for CAS pro tocols -[...]
-
Seite 221
Mediant 2000 SIP User’s Manual G. Accessory Programs a nd Tools Version 4.4 221 July 2005 Figure H-8: Trunk Traces Figure H-9: UDP2File Utility[...]
-
Seite 222
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 222 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 223
Mediant 2000 SIP User’s Manual H. Software Upgrade Key Version 4.4 223 July 2005 Appendix H Sof tware Upgrade Key H.1 About the Software Upgrade Key Mediant 2000 gateways are sup plied with a Software Upgrade Key already pre-configured f or each of its TrunkPack Modules (TPM). Users can later upg rade their Mediant 200 0 featur es, capabilities a[...]
-
Seite 224
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 224 Document #: LTRT-72504 H.3.1 Loading the Software Upgrad e Key Using the Embedded Web Server To load a Software Upgrade Key us ing the Web Server, take these 5 steps: 1. Access the devices Embedded Web Server (refer to Section 5.5 on page 40 ). 2. Click the Softw are Update button. 3. Click [...]
-
Seite 225
Mediant 2000 SIP User’s Manual H. Software Upgrade Key Version 4.4 225 July 2005 Figure H-2: Example of a Soft ware Upgrade Key File Containing Multiple S/N Lines H.3.2 Loading the Software Upgr ade Key Using BootP/TFTP To load the Software Upgrade Key file using Boot P/TFTP, take these 5 steps: 1. Place the file in the same location you’ve[...]
-
Seite 226
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 226 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 227
Mediant 2000 SIP User’s Manual I. Release Reason Mapping Version 4.4 227 July 2005 Appendix I Release Reason Mapping Table I-1 below describes the mapping of ISDN release reason to SIP respo nse. Table I-2 on page 229 describes the mapping of SIP response to ISDN relea se reason. Table I-1: Mapping of ISDN Release Reason to SIP Response (continue[...]
-
Seite 228
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 228 Document #: LTRT-72504 ISDN Release Reason Description SIP Response Description 66 Channel type not implem ented 480 * Temporarily unavailable 69 Requested facility not implem ented 503 * Service unava ilable 70 Only restricted digital information be arer capability is availabl e 503 * Service u[...]
-
Seite 229
Mediant 2000 SIP User’s Manual I. Release Reason Mapping Version 4.4 229 July 2005 Table I-2: Mapping of SIP Response to ISDN Release Reason SIP Response Description ISDN Release Reason Description 400 * Bad request 31 Normal, unspecified 401 Unauthoriz ed 21 Call rejected 402 Payment requir ed 21 Call rejected 403 Forbidden 21 Call rejected 404 [...]
-
Seite 230
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 230 Document #: LTRT-72504 Reader’s Notes[...]
-
Seite 231
Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 231 July 2005 Appendix J SS7 T unneling The Signaling System 7 (SS7) tunneling feature fa cilitates peer-to-pee r transport of SS7 links between gateways that su pport AudioCodes' u nique MTP2 (Message Transfe r Part) Tunneling application (M2TN) for transferri ng SS7 MTP2 link data[...]
-
Seite 232
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 232 Document #: LTRT-72504 J.1 MTP2 Tunneling Technology The SS7 tunneling technology is based on a pairi ng of remote and central gateways, as shown in Figure J-3 . The remote gateways are configured to bac khaul MTP layer 2 sig naling over the I P network using standa rd M2UA protocol (over S CTP [...]
-
Seite 233
Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 233 July 2005 J.3 SS7 Parameters The parameters in Table J-1 below configure all MTP attributes simultaneo usly. To set each MTP attribute individually, add _xx (xx equals the element number in th e range of 0 to 2) to the en d of the ini file field name. Table J-1: SS7 Parameters (conti[...]
-
Seite 234
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 234 Document #: LTRT-72504 Table J-1: SS7 Parameters (continue s on pages 233 to 234) ini File Parameter Name Description SS7_MTP2_Param_Timer _T6 Defines the SS7 MTP2 Remote Con gestion timer (in msec). The valid range is 0 to 10000. The default value is 6000. SS7_MTP2_Param_Timer _T7 Defines the S[...]
-
Seite 235
Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 235 July 2005 Table J-2: SIGTRAN Interface Groups (con tinues on pages 234 to 235 ) ini File Parameter Name Description SS7_LOCAL_SCTP_PORT Determines the SIGTRAN group SCTP port. The valid range is 0 to 0x FFFE. The default value is 0Xfffe. SS7_SIG_NETWORK Determines the SIGTRAN group N[...]
-
Seite 236
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 236 Document #: LTRT-72504 J.4.3 SS7 Signaling Link Table J-4: SS7 Signaling Link (continues on page s 236 to 2 37) ini File Parameter Name Description SS7_LINK_INDEX Determines the index field for a line. The valid range is 0 to 7. The default value i s 0. SS7_LINK_ROWSTATUS Determines the RowStatu[...]
-
Seite 237
Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 237 July 2005 Table J-4: SS7 Signaling Link (continues on page s 236 to 2 37) ini File Parameter Name Description SS7_LINK_GROUP_ID Determines the group ID (M3 UA) of signaling link. The valid range is 0 to 0x FFFF. The default va lue is 0. ATM_SAAL_LINK_PROFILE_NUM Determines the ATM SA[...]
-
Seite 238
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 238 Document #: LTRT-72504 • There are 8 SS7 links - 4 links of type: MTP2 MGC, and 4 links of type MTP2. Each pair of links (1 MTP2 MGC and 1 MTP2) defines an MTP2 tunnel. • There is 1 interface that is used for the M2UA MG C <=> M2UA SG (Signaling Gateway) connectio n. • There are 4 in[...]
-
Seite 239
Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 239 July 2005 Figure J-4: SS7 MTP2 Tunneling ini File Example - MGC SS7_MTP2_PARAM_TIMER_T4E_0=500 SS7_MTP2_PARAM_TIMER_T4N_0=8200 SS7_MTP2_PARAM_TIMER_T5_0=100 SS7_MTP2_PARAM_TIMER_T6_0=3000 SS7_MTP2_PARAM_TIMER_T7_0=2000 [syslog] SYSLOGSERVERIP = 168.100.0.1 ENABLESYSLOG = 1 ;FORCEEXCE[...]
-
Seite 240
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 240 Document #: LTRT-72504 Figure J-4: SS7 MTP2 Tunneling ini File Example - MGC SS7_SIG_IF_GROUP_TABLE 4 = 4, 77, 4, 1, 2000, 2000, 30000, 1, 0, 2904, 1,2904,168.100.0.2,3,3; [ SS7_SIG_IF_GROUP_TABLE ] [ SS7_SIG_INT_ID_TABLE ] FORMAT SS7 _ SIG _ IF _ ID _ INDEX = SS7 _ SIG _ IF _ ID _ VALUE, SS7 _[...]
-
Seite 241
Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 241 July 2005 Figure J-5: SS7 MTP2 Tunneling ini File Example - SG SS7_LINK_TABLE 1 = new_link_1, 0, 2, 1,1, 2, 12, 12; SS7_LINK_TABLE 2 = new_link_2, 0, 2, 1, 1, 4, 7,18; SS7_LINK_TABLE 3 = new_link_3, 0, 2, 1, 1, 5, 3,1; [SS7_LINK_TABLE] [ SS7_SIG_IF_GROUP_TABLE ] FORMAT SS7_SIG_IF_GR[...]
-
Seite 242
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 242 Document #: LTRT-72504 Table J-5: Table of Parameter Values Example - Remote Mana gement Connections Index Fields: 1. Connection Number Connection Number User Name User Password Time Connected (msec) Permissions 0 Admin Yellow9 0 All 1 Gillian Red5 1266656 Read Only 2 David Orange6 0 Read Write [...]
-
Seite 243
Mediant 2000 SIP User’s Manual J. SS7 Tunneling Version 4.4 243 July 2005 J.6.3 Tables of Parameter Value Rules in the ini File Structure The ini file allows you to add/modify parameters in tables. When using tables, Read-Only parameters are not loaded, since th ey cause an error when trying to download the loaded file. Therefore read-only param [...]
-
Seite 244
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 244 Document #: LTRT-72504 • The order of the Data fields in the Format line is not significa nt (unlike the Index-fields). Field values in Data lines are int erpreted according to the o rder specified in the Forma t line. • The sign '$$' in the Data line means that t he user wants the[...]
-
Seite 245
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 245 July 2005 Appendix K RADIUS Bil ling and VXML Calling Card Application The Mediant 2000 calling card appli cation capability (included in its IVR - Interactive Voice Response - feature ) enables Internet Teleph ony Service Providers (ITSPs) to provi[...]
-
Seite 246
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 246 Document #: LTRT-72504 • Loads the VXML script s once and stores them in t he RAM; scripts can b e changed without the need of reset • Barge-in dialing (to shorten menu time), once p rompt has started K.3 Supported Architecture Figure K-1: Mediant 2000 Supported Architecture Figure K-1 illus[...]
-
Seite 247
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 247 July 2005 K.4 Implementation The Mediant 2000 uses an emb edded VoiceXML int erpreter to interpret and execute standard VoiceXML scripts, which a re loaded from an outbou nd HTTP server and stored in the gateway’s volatile memory (RAM). The pre de[...]
-
Seite 248
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 248 Document #: LTRT-72504 K.4.2 Call Flow Description Figure K-2 on the previous p age depict s an example of a stan dard PSTN IP call (billing-model: debit). • An incoming PSTN call with a publi shed access number reaches the Media nt 2000. • The Mediant 2000 accepts the call (sen ds an Al[...]
-
Seite 249
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 249 July 2005 K.5 Operation & Configuration To start working with the IVR system, take these 6 steps: 1. Install the Mediant 2000 (refer to Section Installing the Mediant 2000 on page 27 and to Section Getting Started on page 35 ). 2. Create and[...]
-
Seite 250
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 250 Document #: LTRT-72504 ini File Field Name Valid Range and Description IVR Reference NumberMapIP2Tel Manipulate the destination number for IP to Tel calls. NumberMapIP2Tel = a,b,c,d,e,f,g,h,i a = Destination number prefix b = Number of stripped digits from the left, or (if brackets are used) fro[...]
-
Seite 251
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 251 July 2005 • RADIUSAuthServerIP • RADIUSAuthPort • RADIUSAccServerIP • RADIUSAccPort • AAAIndications • RADIUSAccountingType K.7 Supported RADIUS Attributes Use Table K-3 below for explanations on the RADI US attributes contained in th e [...]
-
Seite 252
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 252 Document #: LTRT-72504 Table K-3: Supported RADIUS Attributes (continues on page s 251 to 252) Attribut e Number Attribut e Name VSA No. Purpose Value Format Sample AAA 2 26 h323-gw-id 33 Name of the gate w ay String SIPIDString Start Acc Stop Acc String 80045 67145 Start Acc 30 Called-Station-I[...]
-
Seite 253
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 253 July 2005 K.8 RADIUS Server Messages Note: In Figure K-4 , Figure K-5 and Figure K-6 non-standard pa rameters are preceded with brackets. K.8.1 Authentication Figure K-4: Authentication Example Access-Request (116) user-name = 111 user-password = (e[...]
-
Seite 254
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 254 Document #: LTRT-72504 12.1.2 Accounting Figure K-6: Accounting Example Accounting-Request (361) user-name = 111 acct-session-id = 1 nas-ip-address = 212.179.22.213 nas-port-type = 0 acct-status-type = 2 acct-input-octets = 4841 acct-output-octets = 8800 acct-session-time = 1 acct-input-packets [...]
-
Seite 255
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 255 July 2005 The user_passwd parameter (that initially containe d the user pa ssword collected from the user) is being assigned the value ‘domain '+user_passwd + '.com’. • Calling number (recived form SIP incoming call ) ca n optionally[...]
-
Seite 256
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 256 Document #: LTRT-72504 K.10 Supported Elements & Attributes Table K-4: VoiceXML Supported Elements & Attributes (continues on pa ges 256 to 260) Element Element’s Description Parameter s Paramete r’s D escription Supported name T he name of the modified variable <assign> Assign[...]
-
Seite 257
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 257 July 2005 Table K-4: VoiceXML Supported Elements & Attributes (continues on pa ges 256 to 260) Element Element’s Description Parameter s Paramete r’s D escription Supported modal If this is false (the default) all active grammars are turned [...]
-
Seite 258
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 258 Document #: LTRT-72504 Table K-4: VoiceXML Supported Elements & Attributes (continues on pa ges 256 to 260) Element Element’s Description Parameter s Paramete r’s D escription Supported label A string which may be used. <log> Generate a debug message expr An ECMAscript expression e[...]
-
Seite 259
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 259 July 2005 Table K-4: VoiceXML Supported Elements & Attributes (continues on pa ges 256 to 260) Element Element’s Description Parameter s Paramete r’s D escription Supported finalsilence The interval of silence that indicates end of speec h. [...]
-
Seite 260
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 260 Document #: LTRT-72504 Table K-4: VoiceXML Supported Elements & Attributes (continues on pa ges 256 to 260) Element Element’s Description Parameter s Paramete r’s D escription Supported transferaudi o The URI of audio source to play w hile the transfer attempt is in progress (before far-[...]
-
Seite 261
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 261 July 2005 8. “Your account number a nd password do not match”. 9. “We are having technical difficulties, please call agai n later”. 10. “Please enter the number that you wi sh to call followe d by the pound key”. 11. “The number you ar[...]
-
Seite 262
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 262 Document #: LTRT-72504 K.11.2 VXML Flow Chart Figure K-7: VXML Script Opening Menu Play VP 1 No No No No No Yes Start No Yes Yes Yes Yes Go To Start Go To 1 Go To 4 Go To St art Go To End Play VP 3 Play VP 4 Play VP 2 Pressed 1? DTMF Pressed? Pressed 2? Yes Go To 2 Pressed 3? Go To 3 Pressed 4? [...]
-
Seite 263
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 263 July 2005 Figure K-8: VXML Script Option 1, Make a Call No Yes 1 No Yes Yes No No Wa i t s f o r Authentication No Yes Yes Go To 1 Go To T ransfer Go To En d Play VP 5 Play VP 3 Play VP 6 Play VP 3 Play VP 7 Play VP 7 Play VP 4 DTMF Pr essed? DTMF P[...]
-
Seite 264
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 264 Document #: LTRT-72504 Figure K-9: VXML Script, Call Transfer Procedure End DTMF Pres sed? No Play VP 3 Yes Play VP 15 Go to Trans fer Call for tr ansfer service Tr ansfer Failed? Play either VP 11, 12 or 13 accord ing to Tran sfer fai lu re reason Go to End No No Yes Debit? Final alert time exp[...]
-
Seite 265
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 265 July 2005 Figure K-10: VXML Script, Options 2, 3 and 4 2 Play VP 17 Go To S tar t 3 End Tra ns fer C al l To an Oper ator 4 End Play VP 16 Figure K-11: VXML Script, Call Termination No End Yes End Play VP 16 Go To Sta rt VXML Scr ipt Term inated? Fr[...]
-
Seite 266
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 266 Document #: LTRT-72504 K.12 VXML Script Example Figure K-12: VXML Script Example (continues on pages 266 to 270) <?xml version="1.0" encoding="UTF-8"?> <vxml version="1.0" application="http://phoenix1.iperia.com:8080/sa3/jsp/sa.jsp"> <var na[...]
-
Seite 267
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 267 July 2005 Figure K-12: VXML Script Example (continues on pages 266 to 270) <if cond="AAStatus==0"> <goto next="#PerformAuthen"/> <else/> <goto next="#PerformTransfer"/> </if> <elseif con[...]
-
Seite 268
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 268 Document #: LTRT-72504 Figure K-12: VXML Script Example (continues on pages 266 to 270) </form> <form id="GetCalledPartyTelephone"> <log label="starting get called party telephone form" cond="'1' == '1'"/> <field name="d[...]
-
Seite 269
Mediant 2000 SIP User’s Manual K. RADIUS Billing and VXML Calling Card Application Version 4.4 269 July 2005 Figure K-12: VXML Script Example (continues on pages 266 to 270) <param name="password" expr="AuthenticationInfo.user_passwd"/> <nomatch> <prompt> <audio src="/8.wav"> your account and [...]
-
Seite 270
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 270 Document #: LTRT-72504 Figure K-12: VXML Script Example (continues on pages 266 to 270) called transfer failed </audio> </prompt> <goto next="#main_menu"/> <elseif cond="mycall.Result=='busy'"/> <prompt> <audio src="/11.wav"[...]
-
Seite 271
Mediant 2000 SIP User’s Manual L. SNMP Traps Version 4.4 271 July 2005 Appendix L SNMP T rap s This section provides information on proprietary SNMP trap s currently su pported by the g ateway. There is a separation bet ween traps that are al ar ms and traps that are not (logs). Currently all have the same structu re made up of the same 10 varbin[...]
-
Seite 272
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 272 Document #: LTRT-72504 Table L-2: acBoardConfigurationErr or Alarm Trap Corrective Action: Inspect the run-time specific string to determine the nature of t he configuration err or. Fix the configuration error using t he appr opriate tool: Web interface, EMS, or ini file. Save the configuration [...]
-
Seite 273
Mediant 2000 SIP User’s Manual L. SNMP Traps Version 4.4 273 July 2005 Table L-5: acFeatureKeyError Alarm T rap Condition: After raise Alarm status: Status stays critical until reboot. A clear trap is not sent. Corrective Action: Obtain a corrected feature key from AudioCodes, activa te it b y loading to the device, then reset the device. Table L[...]
-
Seite 274
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 274 Document #: LTRT-72504 Table L-8: acBoardOverloadAlarm Ala rm Trap Condition: An overl o ad condition exists in one or more of the system components. Alarm Status: Major Condition: T he overload condition passed Alarm Status: Cleared[...]
-
Seite 275
Mediant 2000 SIP User’s Manual L. SNMP Traps Version 4.4 275 July 2005 L.1.2 Component: AlarmManager#0 Table L-9: acActiveAlarmTableOv erflow Alarm Trap Alarm: acActiveAlarmTableOverflo w OID: 1.3.6.1.4.15003. 9.10.1.21.2.0.12 Default Severity Major Event Ty pe: processingErrorAlarm Probable Cause: resourceAtOrNearingCapacit y (43) Alarm Text: Ac[...]
-
Seite 276
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 276 Document #: LTRT-72504 L.1.4 Other Traps The following are provided as SNMP traps an d are not alarms. Table L-11: coldStart Trap Trap Name: coldStart OID: 1.3.6.1.6. 3.1.1.5.1 MIB SNMPv2-MIB Note: This is a trap from the standar d SNMP MIB. Table L-12: authenticatio nFailure Trap Trap Name: aut[...]
-
Seite 277
Mediant 2000 SIP User’s Manual M. Regulatory Information Version 4.4 277 July 2005 Appendix M Regulatory Information Declaration of Conformity Application of Council Direc tives : 73/23/EEC (including amendments), 89/336/EEC (including amendments), 1999/5/EC Annex-II of the Directive Standards to which Con f ormity is Declared : EN55022: 1998, Cl[...]
-
Seite 278
Mediant 2000 SIP Mediant 2000 SIP User’s Manual 278 Document #: LTRT-72504 Industry Canada Notice This equipment meets the applicable Industry Canada Terminal Equipment technical specif ications. This is confirmed by the registration numbers. The abbreviation, IC, befor e the registrati on number signifies that regist ration was performed based o[...]
-
Seite 279
Mediant 2000 SIP User’s Manual M. Regulatory Information Version 4.4 279 July 2005 Original printed on recycled paper and available on CD or Web site[...]
-
Seite 280
AudioCodes Offices International Headquar te rs AudioCodes Ltd. 1 Hayarden Street, Airport City, Lod 70151, Isra el. Tel: +972-3-976 4000 Fax: +972-3-976 4040 Email: info@audiocodes.com USA Headquarters AudioCodes, Inc. 2099 Gateway Place, Suite 500 San Jose, CA 95110 Tel: +1-408-411-1175 Fax: +1-408-451-9520 Email: info@audiocodes.com USA Offices [...]