Oki 6100E+ Bedienungsanleitung

OkiLAN 6100e+ ® User ’ s Guide High Performance Ethernet Network Print Server[...]

ii Copyright and T rademark Information OKI OkiLAN 6100e+ User ’ s Guide Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki Data assumes no responsibility for the results of errors beyond its control. Oki Data also cannot guarantee that changes in products made by other manufactur[...]

iii Organization and Contents OKI OkiLAN 6100e+ User ’ s Guide Organization This manual has been divided into eight sections. Section I contains and installation instructions for the OkiLAN 6100e+ print server . Section II contains information about management features, an extremely valuable set of OkiLAN 6100e+ management tools for network admin[...]

iv Organization and Contents OKI OkiLAN 6100e+ User ’ s Guide Section IV : TCP/IP ................................................. IV -1 Chapter 1: Introduction ................................................ IV -5 Chapter 2: Configuring the OkiLAN 6100e+ .............. I V -7 Chapter 3: TCP/IP Configuration and Printing .......... IV -14 Chapt[...]

v Organization and Contents OKI OkiLAN 6100e+ User ’ s Guide Section IX: Regulatory Information ..................... IX-1 Section X: IR Printing ............................................ X- 1 Chapter 1: IR Tranceiver Features ................................ X -3 Chapter 2: Installation and Configuration ..................... X- 5 Chapter 3: [...]

vi Network Operating Systems OKI OkiLAN 6100e+ User ’ s Guide Network Operating Systems Overview OkiLAN 6100e+ simultaneously supports several network protocols in various combinations. Below is a list of supported network protocols accompanied with NOS/OS requirements. Novell NetW are Novell NetW are versions 3.x, 4.1 and higher . Banyan VINES B[...]

vii T echnical Support OKI OkiLAN 6100e+ User ’ s Guide Service Information Note: This information is valid for the United States and Canada only . Okidata On Line V isit the OKI DA T A W eb Site at http://www .okidata.com for the latest information on: • Software drivers • Product guides • Customer support • Corporate information • Dea[...]

viii T echnical Support OKI OkiLAN 6100e+ User ’ s Guide Oki Data Customer Support Representatives Agents are available 24 hours a day , 7 days a week at 1-800-OKIDA T A (1-800-654-3282). Please be sure that you are calling from a telephone close to your printer , so you can describe your problem accurately . Our customer service representatives [...]

ix T echnical Support OKI OkiLAN 6100e+ User ’ s Guide Brazil Oki Data do Brasil, Ltda. T el: 55-1 1-501 1-1518 Fax: 55-11-5012-0267 Mexico Oki Data de Mexico, S.A. de C.V . T el: 525-661-6860 Fax: 525-661-5861[...]

x T echnical Support OKI OkiLAN 6100e+ User ’ s Guide When you call T echnical Support, the following information will help us answer your questions more quickly and accurately . Please be able to identify the following: • OkiLAN model number • Serial number • Configuration sheet settings • T ype of network cable connected to the OkiLAN 6[...]

Hardware Installation Section I: Hardware Installation[...]

I - 2 Section I - Har dware Installation OKI OkiLAN 6100e+ User ’ s Guide In This Section Chapter 1: Installing the OkiLAN 6100e+ ............... I-3 Hardware Installation ..................................... I-3 Installing the OkiNet Utilities in W indows .... I-8 W indows Utility Groups ................................. I-9 Appendix A: Hardwar[...]

I - 3 Section I - Chapter 1 - Installing the OkiLAN 6100e+ OKI OkiLAN 6100e+ User ’ s Guide Hardware Installation Chapter 1 Installing the OkiLAN 6100e+ The OkiLAN 6100e+ 1. T urn the printer off. 2. Unplug the power cord. 3. Detach the interface cable from the back of the printer .[...]

I - 4 Section I - Chapter 1 - Installing the OkiLAN 6100e+ OKI OkiLAN 6100e+ User ’ s Guide 4. Push the OPEN button, then open the top cover . 5. Remove and save the two large screws on the right side, which hold the side panel in place. 6. Pull the side panel out and remove it from the printer[...]

I - 5 Section I - Chapter 1 - Installing the OkiLAN 6100e+ OKI OkiLAN 6100e+ User ’ s Guide Hardware Installation 7a. OKIP AGE 16n, 18, 20, 20DX and 24DX: Remove and save the two screws on the left of the metal plate covering the internal board, then pull the plate out about an inch and lift it out. Pry off the plastic cutout on the back of the p[...]

I - 6 Section I - Chapter 1 - Installing the OkiLAN 6100e+ OKI OkiLAN 6100e+ User ’ s Guide 8. Plug the connector on the OkiLAN board into the socket on the board in the printer . Make sure the pins are aligned properly . 9. Fasten the OkiLAN board into place with the supplied mounting screws. 10. Replace the metal plate and secure it with the sc[...]

I - 7 Section I - Chapter 1 - Installing the OkiLAN 6100e+ OKI OkiLAN 6100e+ User ’ s Guide Hardware Installation 1 1. Replace the side panel (tabs go in slots): you’ll need to move the cover hinge out of the way before you put the side panel back in place. 12. Secure the panel in place with the two screws. 13. Close the printer cover . If the [...]

I - 8 Section I - Chapter 1 - Installing the OkiLAN 6100e+ OKI OkiLAN 6100e+ User ’ s Guide 14. Attach one end of the cable to the connector on the OkiLAN board, and the other end to the parallel connector of the printer . Secure the cable at both ends. 15. Plug the power cord into the power outlet. Installing the OkiNet Utilities in Windows 1. I[...]

I - 9 Section I - Chapter 1 - Installing the OkiLAN 6100e+ OKI OkiLAN 6100e+ User ’ s Guide Hardware Installation Windows Utility Groups: NetW are Management Utilities OkiNet Utility for NetW are OkiNet Utility for NDS (W orkstation and Server) OkiNet Utility for NDS (W orkstation) OkiNet Connect Windows Printing OkiNet Connect for TCP/IP (W indo[...]

I - 10 Section I - Appendix A - Har dware T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide Appendix A Hardware T roubleshooting OkiLAN 6100e+ Print Server Status PTR light on = printer port initialized N/W light on = n/w connection established Flashes w/n/w traffic 100 Mb On =100 Off =10[...]

I - 11 Section I - Appendix A - Har dwar e T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide Hardware Installation Unable to Print If your OkiLAN 6100e+ passes self-test and you are unable to print a configuration sheet or are unable to send data to the printer via the OkiLAN 6100e+, check the following: • Printer configuration • Printer har[...]

I - 12 Section I - Appendix B - Sample Configuration Sheet OKI OkiLAN 6100e+ User ’ s Guide Appendix B Sample Configuration Sheet OkiLAN 6100e+ Configuration Sheet Page 1 6100e+ OkiLAN 6100e+ Configuration Sheet Page 1 Oki Data 2000 Bishops Gate Boulevard, Mt. Laurel NJ 08054 Customer Support 1-800-OKIDA T A (1-800-654-3282) USA and Canada http:/[...]

I - 13 Section I - Appendix B - Sample Configuration Sheet OKI OkiLAN 6100e+ User ’ s Guide Hardware Installation OkiLAN 6100e+ Configuration Sheet page 2 EtherT alk (ENABLED) Node Address: 0064:D5h Router Address: 008C:32h Port 1 Enabled Printer Name: “OKI 13011” Printer T ype 1: “LaserWriter” Zone Name: “No Passing Zone” Banyan VINE[...]

I - 14 Section I - Appendix C - W iring Specifications OKI OkiLAN 6100e+ User ’ s Guide Appendix C Wiring Specifications Connector Specifications For your reference, we have included the following connector pin assignments. OKILAN 6100E+, ETHERNET , 10/100BASE-T CONNECTOR SIGNAL ASSIGNMENTS Pin # ......... Signal Name ........... Description 1 ..[...]

I - 15 Section I - Appendix C - W iring Specifications OKI OkiLAN 6100e+ User ’ s Guide Hardware Installation OkiLAN 6100e+ Parallel Output Port Pin 1 Pi n 19 Pin 36 Pin 18 16.3 mm 69 mm All dimensio ns are shown in milli meters and a re inclu ded for referenc e only IE EE 12 84-C Plug IEEE 1284 -B Plug 8 mm 32.4 mm Pin 1 Pin 18 Pin 19 Pin 36 360[...]

I - 16 Section I - Appendix D - Cable Schematics OKI OkiLAN 6100e+ User ’ s Guide Appendix D Cable Schematics 22 4 21 3 20 2 19 1 26 8 25 7 24 6 23 5 30 12 29 11 28 10 27 9 34 16 33 15 32 14 31 13 35 17 36 18 IEEE 12 84-C (0.050 C enterline) PIN IEEE 12 84-B (0.085 Centerline) PIN 29 32 33 10 28 13 35 11 22 4 21 3 20 2 34 12 26 8 25 7 24 6 23 5 3[...]

Advanced Management Section II: Advanced Management Features[...]

II - 2 Section 2 - Advanced Management Featur e OKI OkiLAN 6100e+ User ’ s Guide In This Section Chapter 1 SNMP ...................................................... II-3 Overview ....................................................... II-3 Private MIB ................................................... II-3 T raps ..............................[...]

II - 3 Section 2 - Chapter 1 - SNMP OKI OkiLAN 6100e+ User ’ s Guide Advanced Management Chapter 1 Single Network Management Protocol (SNMP) Overview Simple Network Management Protocol (SNMP) provides network administrators with the ability to communicate management functions between an SNMP manager and an SNMP agent. An SNMP manager is a user pr[...]

II - 4 Section 2 - Chapter 1 - SNMP OKI OkiLAN 6100e+ User ’ s Guide Note : If you attempt a reset while a job is printing, the job may not print successfully . Certain variables are critical, that is, they change a fundamental operating parameter of the OkiLAN 6100e+. These variables are saved by the OkiLAN 6100e+ but are not actually used until[...]

II - 5 Section 2 - Chapter 1 - SNMP OKI OkiLAN 6100e+ User ’ s Guide Advanced Management In order to receive OkiNet Alert traps, the OkiLAN 6100e+ must have bi-directional status enabled (it is disabled by default). Extended Status can be enabled through the OkiLAN 6100e+ Configuration utility (telnet) from the Configur e Port option. Y ou can al[...]

II - 6 Section 2 - Chapter 2 - Banyan Outlook OKI OkiLAN 6100e+ User ’ s Guide Chapter 2 Banyan Outlook The OkiNet for VINES and OkiNet for NetW are utilities can be launched from within the Banyan VINES Outlook network management software. When running these utilities within Outlook, the same software requirements apply as when the utilities are[...]

II - 7 Section 2 - Chapter 3 - HP JetAdmin Support OKI OkiLAN 6100e+ User ’ s Guide Advanced Management Chapter 3 HP JetAdmin Support Overview This section contains instructions and information on how to configure and obtain diagnostic information from your OkiLAN 6100e+ using the Hewlett-Packard JetAdmin software. Software Requirements • JetAd[...]

II - 8 Section 2 - Chapter 3 - HP JetAdmin Support OKI OkiLAN 6100e+ User ’ s Guide 7. Select the desired queues from the list of A vailable Queues to be added into service. Click the Service button to move the selection to the Serviced Queues column. When all queues have been added, click OK . 8. Click OK again to return to the main screen. W AR[...]

II - 9 Section 2 - Chapter 4 - HP W eb JetAdmin Support OKI OkiLAN 6100e+ User ’ s Guide Advanced Management Chapter 4 HP W eb JetAdmin Support Overview This section contains instructions and information on how to configure, install, and obtain diagnostic information from your OkiLAN 6100e+ using the Hewlett-Packard W eb JetAdmin software. Softwa[...]

II - 10 Section 2 - Chapter 4 - HP W eb JetAdmin Support OKI OkiLAN 6100e+ User ’ s Guide 4. On the Install Printer Page 1 page, select an NT domain from the pull-down menu. Enter the user name and password of a domain user with sufficient rights to create a printer and click the Continue button. 5. On the Install Printer Page 2 page, select the [...]

II - 11 Section 2 - Chapter 5 - OkiLAN 6100e+ W eb Configuration OKI OkiLAN 6100e+ User ’ s Guide Advanced Management Chapter 5 OkiLAN 6100e+ Web Configuration Overview This section contains instructions and information on how to configure and manage your OkiLAN 6100e+ using a standard W eb browser . Software Requirements TCP/IP Protocol Netscape[...]

II - 12 Section 2 - Chapter 5 - OkiLAN 6100e+ W eb Configuration OKI OkiLAN 6100e+ User ’ s Guide Note : As a layer of security , the TCP port number that the device uses to communicate with browsers, called the HTTP port , can be modified from a default of 80. If the port is modified, the HTTP address put in the browser must include the port num[...]

II - 13 Section 2 - Chapter 5 - OkiLAN 6100e+ W eb Configuration OKI OkiLAN 6100e+ User ’ s Guide Advanced Management Configuration 1. Select the Login as Admin link under the Configuration menu. 2. On the Enter Network Passwor d screen, enter the User name and Passwor d . The default administrator User name is admin . The default administrator P[...]

II - 14 Section 2 - Chapter 5 - OkiLAN 6100e+ W eb Configuration OKI OkiLAN 6100e+ User ’ s Guide W ARNING: Changes will not be saved if the Submit Changes button is not selected before continuing to another page. 5. A Request Results page will appear indicating one of the following: • Configuration Successfully Set : The values have been succe[...]

II - 15 Section 2 - Chapter 5 - OkiLAN 6100e+ W eb Configuration OKI OkiLAN 6100e+ User ’ s Guide Advanced Management interface: Web Admin Configuration Under the Configuration menu, select the Admin(W eb) link. • Admin Name - The name used to access full configuration privileges. The default Admin Name is admin . • Admin Password - This fiel[...]

II - 16 Section 2 - Chapter 5 - OkiLAN 6100e+ W eb Configuration OKI OkiLAN 6100e+ User ’ s Guide Status The home page for the print server shows general status information including the status of all printers currently attached. For more detailed status information, select the V iew Cnfg Sheet link under the Status menu. This will show informati[...]

II - 17 Section 2 - Chapter 5 - OkiLAN 6100e+ W eb Configuration OKI OkiLAN 6100e+ User ’ s Guide Advanced Management Reset Reset Reset the print server by selecting the Reset link under the Reset menu. A message will appear asking you to confirm the reset. Restore Select Restore Defaults under the Reset menu to restore selected protocols to fact[...]

II - 18 Section 2 - Chapter 5 - OkiLAN 6100e+ W eb Configuration OKI OkiLAN 6100e+ User ’ s Guide T roubleshooting Server Connection • The print server only supports two simultaneous HTTP connections. If your browser fails to connect to the print server , the browser may be trying to open more than two connections. Please refer to your browser [...]

II - 19 Section 2 - Chapter 6 - Additional Management Featur es OKI OkiLAN 6100e+ User ’ s Guide Advanced Management Chapter 6 Additional Management Features OkiNet Alert OKI OkiNet Alert enterprise management utility allows administrators to proactively manage printers by being immediately alerted to printing problems before they are encountered[...]

II - 20 Section 2 - Chapter 6 - Additional Management Featur es OKI OkiLAN 6100e+ User ’ s Guide OkiNet for NDS OkiNet for NDS allows administrators to create and manage OKI print server objects in the NDS tree. OkiNet for NDS integrates into Novell’ s NetW are Administrator , NetW areAdmin. For more information, see OkiNet for NDS under NetW a[...]

NetWare Section III: Netware[...]

III - 2 Section 3 - NetW are OKI OkiLAN 6100e+ User ’ s Guide In This Section Chapter 1 Introduction ........................................... III-4 Overview ...................................................... III-4 Before Y ou Start ........................................... III-4 Selecting PServer or RPrinter/NPrinter Mode ...............[...]

III - 3 Section 3 - NetW are OKI OkiLAN 6100e+ User ’ s Guide NetWare Chapter 3 OkiNet for NDS .................................... III-24 Overview .................................................... III-24 Installing OkiNet for NDS for Novell NetW are 4. ................................................ III-25 Installing OkiNet for NDS for Novel[...]

III - 4 Section 3 - Chapter 1 - Intr oduction OKI OkiLAN 6100e+ User ’ s Guide Chapter 1: Introduction Overview This section contains instructions and information on how to configure your OkiLAN 6100e+ in the NetW are environment. There are two environments in which to configure the OkiLAN 6100e+: • Bindery (NetW are 3.x) • NetW are Directory[...]

III - 5 Section 3 - Chapter 1 - Intr oduction OKI OkiLAN 6100e+ User ’ s Guide NetWare Selecting PServer or RPrinter/NPrinter Mode Y our OkiLAN 6100e+ supports both PServer and NPrinter mode. There are several factors to consider when choosing which mode to use. In PServer mode, the OkiLAN 6100e+ operates as the print server . It services specifi[...]

III - 6 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide Chapter 2 OkiNet for NetW are Overview This chapter contains information about how to configure the OkiLAN 6100e+ in Bindery and NDS environments using the OkiNet for NetW are utility . Note : OkiNet for NetW are contains minimal NDS configuration support. For mo[...]

III - 7 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetWare Running OkiNet for NetW are T o run the utility , double-click on the OkiNet icon. The main OkiNet for NetW ar e screen will display . By default, the All Print Servers view is selected and all print servers attached to the network from which the OkiNet u[...]

III - 8 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetW are Configuration Options T o configure options specific to the NetW are protocol, select the NetW are file tab. The following screen will display: PServer or RPrinter Mode Several factors should be considered when choosing between PServer or RPrinter mode. [...]

III - 9 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetWare NDS printer objects. Once you have created NDS objects and queues, use the OkiNet for NetW are utility to configure the following fields: • Preferred File Server - This is the file server on which the print server object was created. • Preferred T ree[...]

III - 10 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetW are Port Configuration Options T o modify the NetW are port settings to fit your NetW are printing environment, select the NetW are Port file tab. TCP/IP Configuration Options T o modify configuration settings specific to the TCP/IP protocol such as IP addr[...]

III - 11 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetWare Output Port Configuration Options T o configure the OkiLAN 6100e+ output port, select the Output Port file tab. The following screen will display: Port Number Select the port you wish to configure. Name Field Enter a descriptive name to identify the port[...]

III - 12 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide and inserts the appropriate character string in front of each print job to switch the printer to the appropriate printer language. Note : If you are not switching languages or the printer can switch languages automatically , this option should be set to OFF . Pr[...]

III - 13 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetWare Output T ype Select the desired level of support for 1284 communications. The following settings are available: - Compatibility (no bidi) - 1284 (Std Nibble Mode) (default) - 1284 (ECP or Fast Nibble Mode) SNMP Configuration Options SNMP options specify [...]

III - 14 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide Fill in the following information: System Name Enter the name of your choice. This name will identify the OkiLAN 6100e+ in your SNMP-based management program. System Contact Enter any information useful to a user if problems with the OkiLAN 6100e+ arise. System [...]

III - 15 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetWare Trap Community Name Enter the community name which will be used when traps are sent from the OkiLAN 6100e+. This setting allows trap utilities to only accept traps from devices with appropriate community names. The T rap community name field is used by t[...]

III - 16 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide Trap Destination • NetW are Protocol - Enter the network number and hardware address, respectively , to which traps will be sent. T o broadcast traps to all addresses on all networks, enter FFFFFFFF (8 characters) in the first field and FFFFFFFFFFFF (12 charac[...]

III - 17 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetWare Enabling/Disabling Protocols T o enable or disable protocols on the OkiLAN 6100e+, select the Protocols file tab. Select each protocol you wish to enable. If you disable a protocol, the OkiLAN 6100e+ will no longer communicate using that protocol. T o re[...]

III - 18 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide Resetting the OkiLAN 6100e+ T o reset the OkiLAN 6100e+, select the OkiLAN 6100e+ from the list of available print servers. From the Print Server menu bar , select Reset . CAUTION: Make sure there are no print jobs active when you reset the OkiLAN 6100e+. All pr[...]

III - 19 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetWare CAUTION: Make sure there are no active print jobs when you select Restore Factory Defaults. If you reset the OkiLAN 6100e+ while a job is printing, the job may not print successfully . Creating Customized Views OkiNet for NetW are allows users to create [...]

III - 20 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide Modifying View Settings Before modifying the settings, select the name of the view you wish to edit from the Name field. Display Filter The filter option displays only those print servers matching specific criteria. The print server list can be filtered by any o[...]

III - 21 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetWare • Specify Devices/Networks - This method adds specific print servers (or groups of print servers) to the list. This can be useful when only a subset of the list of OkiLAN 6100e+ products is desired. T o select all desired print servers, select Add . So[...]

III - 22 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide Refresh The refresh rate defines how often the OkiNet for NetW are utility updates the main print server list. T o define a refresh rate, select the Automatic Refresh box and then enter the refresh rate in the field provided. Decide how frequently to refresh the[...]

III - 23 Section 3 - Chapter 2 - OkiNet for NetW are OKI OkiLAN 6100e+ User ’ s Guide NetWare Set Community Name Enter the Set Community Name necessary to access the OkiLAN 6100e+ or group of OkiLAN 6100e+ products selected. Add Select the Add button to define access to a new OkiLAN 6100e+ or a group of OkiLAN 6100e+ products. Enter a serial numb[...]

III - 24 Section 3 - Chapter 3 - OkiNet for NDS OKI OkiLAN 6100e+ User ’ s Guide Chapter 3 OkiNet for NDS Overview OkiNet for NDS is a Dynamic Link Library (DLL) which allows users to create and manage OKI print server objects in the NDS tree. OkiNet for NDS integrates into Novell’ s NetW are Administrator , a W indows-based utility that allows[...]

III - 25 Section 3 - Chapter 3 - OkiNet for NDS OKI OkiLAN 6100e+ User ’ s Guide NetWare Refer to the following table to determine which method to use to install OkiNet for NDS: NetW are V ersion Client Operating System W indows 3.x W indows 95/98 W indows NT/2000 NetW are 4.1 See Installing OkiNet for NDS for Novell NetW are 4.1 NetW are 4.1 1 S[...]

III - 26 Section 3 - Chapter 3 - OkiNet for NDS OKI OkiLAN 6100e+ User ’ s Guide 3. If OkiNet for NDS is installed on the file server , anybody using NetW are Administrator on the network can use it. T o do so, they must add the following text to the NW ADMIN.INI file in their W indows directory: [Snapin Object DLLs] SNAPIN=XVIEWNDS.DLL Installin[...]

III - 27 Section 3 - Chapter 3 - OkiNet for NDS OKI OkiLAN 6100e+ User ’ s Guide NetWare Installing OkiNet for NDS for Novell NetW are 4.1 1 and Windows 95/98 and Windows NT/2000 OkiNet for NDS must be installed in the same location you have installed NetW are Administrator . This may be located on the file server or on an independent workstation[...]

III - 28 Section 3 - Chapter 3 - OkiNet for NDS OKI OkiLAN 6100e+ User ’ s Guide Creating a New OkiLAN 6100e+ Object T o create a new OkiLAN 6100e+ object from Novell’ s NetW are Administrator , perform the following steps: 1. Select the container (also known as organizational unit) in which you want the object created. For example, to create a[...]

III - 29 Section 3 - Chapter 3 - OkiNet for NDS OKI OkiLAN 6100e+ User ’ s Guide NetWare Note : If the Device list box is still empty , select Find Device . This will allow you to locate the specific device you are trying to define. Y ou will be prompted for the Ethernet address and network number of the device. A mismatch in the OKI device frame[...]

III - 30 Section 3 - Chapter 3 - OkiNet for NDS OKI OkiLAN 6100e+ User ’ s Guide 6. Select Assign . 7. Select or create a NetW are Printer object from the Printer/Queue Assignments dialog. 8. Select or create a NetW are Print Queue object from the Printer/Queue Assignments dialog. 9. Select OK to save your printer and queue selections. Note : T o[...]

III - 31 Section 3 - Chapter 3 - OkiNet for NDS OKI OkiLAN 6100e+ User ’ s Guide NetWare Configuring the OkiLAN 6100e+ Using OkiNet for NDS The following steps outline how to configure an OkiLAN 6100e+. 1. From the NW Admin screen, select (double-click) the OkiLAN 6100e+ you wish to configure. 2. Set the appropriate configuration by choosing the [...]

III - 32 Section 3 - Chapter 3 - OkiNet for NDS OKI OkiLAN 6100e+ User ’ s Guide The install utility on the installation diskette can also be used to remove the OKI print server class. This utility removes the class from Novell’ s NetW are Administrator and removes all the associated files that were copied during the installation process. Note [...]

TCP/IP Section IV : TCP/IP[...]

IV - 2 Section 4 - TCP/IP OKI OkiLAN 6100e+ User ’ s Guide In This Section Chapter 1 Introduction .......................................... IV -5 Overview ...................................................... IV - 5 Software Requirements ................................. IV -5 Network Preparation ..................................... IV - 6 Bef[...]

IV - 3 Section 4 - TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Saving the Configuration ............................ IV -34 Displaying OkiLAN 6100e+ Diagnostic Information ............................................... IV -34 Printing a Configuration Sheet ................... IV -3 4 Resetting the OkiLAN 6100e+ ..................... IV -34 Re[...]

IV - 4 Section 4 - TCP/IP OKI OkiLAN 6100e+ User ’ s Guide Configuring Solaris 2.x for Printing with the OkiLAN 6100e+ ........................... IV -76 Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6100e+ ....... IV -7 8 Appendix C Internet Printing Protocol (IPP) ..... IV -80[...]

IV - 5 Section 4 - Chapter 1 - Intr oduction OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Chapter 1 Introduction Overview This section contains instructions and information on how to configure your OkiLAN 6100e+. Y ou will also be instructed on how to set up your host computers to print to the OkiLAN 6100e+ using the TCP/IP protocol. OkiLAN 6100e+ sup[...]

IV - 6 Section 4 - Chapter 1 - Intr oduction OKI OkiLAN 6100e+ User ’ s Guide Network Preparation • Y ou should be familiar with network administration as well as the physical setup and operation of your network. • Advise users of possible disruption during installation. • Make sure the serial number and Ethernet address of your OkiLAN 6100[...]

IV - 7 Section 4 - Chapter 2 - Configuring the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Chapter 2 Configuring the OkiLAN 6100e+ Choosing an IP Address Every TCP/IP network device is required to have a unique IP address. The IP address can be permanently stored using one of the following: • OKI OkiNet management utilities for TCP/IP [...]

IV - 8 Section 4 - Chapter 2 - Configuring the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide Configuring the OkiLAN 6100e+ There are four utilities available to configure the OkiLAN 6100e+ for TCP/IP printing. Y ou may use whichever utility is best suited for your needs. • OkiNet for TCP/IP - Windows TCP/IP print manager utility . See Chapter 3[...]

IV - 9 Section 4 - Chapter 2 - Configuring the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide TCP/IP T o use Gleaning, you must have W indows 95/98, W indows NT/2000, or super-user privileges on a UNIX system. 1. Add an entry in the ARP table that assigns an IP address to the hardware address of the OkiLAN 6100e+. T o do this, use the arp command.[...]

IV - 10 Section 4 - Chapter 2 - Configuring the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide DHCP The Dynamic Host Configuration Protocol (DHCP) provides a framework for passing configuration information to hosts on a TCP/IP network in a client/ server fashion. DHCP is based on the Bootstrap Protocol (BOOTP), adding the capability of automatic a[...]

IV - 11 Section 4 - Chapter 2 - Configuring the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Static Route Entry When the OkiLAN 6100e+ is powered on or reset and no permanent IP address has been assigned, it will attempt to obtain an IP address through Gleaning, RARP , BOOTP or DHCP . If the OkiLAN 6100e+ has not determined its IP address[...]

IV - 12 Section 4 - Chapter 2 - Configuring the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide IP addresses. If a match is found, the server ’ s response will include the IP address of the device. Most UNIX operating systems support either the RARP or BOOTP protocol. T o find out which protocol your operating system supports, request the manual [...]

IV - 13 Section 4 - Chapter 2 - Configuring the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide TCP/IP V erifying Access to the OkiLAN 6100e+ Use the ping utility to verify access to the OkiLAN 6100e+. ping < IP addr ess of OkiLAN 6100e+ > If the OkiLAN 6100e+ does not respond, your network or the device is not configured correctly . • V er[...]

IV - 14 Section 4 - Chapter 3 - TCP/IP Configuration and Printing OKI OkiLAN 6100e+ User ’ s Guide Chapter 3 TCP/IP Configuration and Printing Overview The OkiLAN 6100e+ supports printing from computers using TCP/IP and any of the following printing protocols: • Line Printer Redirect/Line Printer Daemon (lpr/lpd) • File T ransfer Protocol (FT[...]

IV - 15 Section 4 - Chapter 3 - TCP/IP Configuration and Printing OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Configuring for TCP/IP Network Printing Most computers that support TCP/IP network printing use the Remote Line Printer Daemon (LPD) protocol. This protocol was originally part of the Berkeley Software Distribution (BSD) version of the UNIX o[...]

IV - 16 Section 4 - Chapter 3 - TCP/IP Configuration and Printing OKI OkiLAN 6100e+ User ’ s Guide The OkiLAN 6100e+ will parse the remote queue name and search for certain characters at the end which tell how to convert an ASCII print job. The print server uses FF , LF and NF as ASCII conversion specifiers and uses the last number as an output p[...]

IV - 17 Section 4 - Chapter 3 - TCP/IP Configuration and Printing OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Configuring a BSD-Style Print Queue For remote BSD-Style LPD printing, add the OkiLAN 6100e+ as a remote printer in the “/etc/printcap” database to each host printing to the OkiLAN 6100e+. Y ou can add PRINTCAP options as needed. If you a[...]

IV - 18 Section 4 - Chapter 3 - TCP/IP Configuration and Printing OKI OkiLAN 6100e+ User ’ s Guide log_file_name This is the path to a file where error information from the lpd will be logged. Example: If you are printing to an ASCII printer that requires a carriage return/line feed, you may need two separate printcap entries: one entry for print[...]

IV - 19 Section 4 - Chapter 3 - TCP/IP Configuration and Printing OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Note: The Remote LPD implementation of the OkiLAN 6100e+ does not support any UNIX LPD input or output filters or the direct printing of banner pages. It is possible to configure some UNIX systems so that banner pages and input and output fil[...]

IV - 20 Section 4 - Chapter 3 - TCP/IP Configuration and Printing OKI OkiLAN 6100e+ User ’ s Guide TYPE Changes the representation type used for data transfer . Image (or binary) and ASCII are the only types supported. ASCII Equivalent to “TYPE ASCII”. BINAR Y Equivalent to “TYPE BINAR Y”. IMAGE Equivalent to “TYPE IMAGE”. STRU Specif[...]

IV - 21 Section 4 - Chapter 3 - TCP/IP Configuration and Printing OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Example: The following example prints a PostScript file called chart.ps to the OkiLAN 6100e+ printer Port 1 using FTP . $ ftp OkiLAN 6100e_name<Enter> Connected to OkiLAN 6100e_name. 220 ESI-2810 V ersion 3.0 ready . Name (OkiLAN 6100e_[...]

IV - 22 Section 4 - Chapter 3 - TCP/IP Configuration and Printing OKI OkiLAN 6100e+ User ’ s Guide Raw Port Printing Host computer software can use a raw TCP/IP port connection to send data to the OkiLAN 6100e+. A TCP/ IP port has been assigned to the output port of the OkiLAN 6100e+ as follows: TCP/IP Port: 9100 Output Port: 1 Consult your syste[...]

IV - 23 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Chapter 4 OkiNet for TCP/IP Overview This section contains information about OkiNet for TCP/IP . OkiNet for TCP/IP provides SNMP-based support for the entire OkiLAN 6100e+ family of print servers. OkiNet for TCP/IP allows you to: • Easily assign an IP addr[...]

IV - 24 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide Running OkiNet for TCP/IP T o run the utility , double-click on the OkiNet icon. The main OkiNet for TCP/IP screen will display . By default, the All Print Servers view is selected and all print servers attached to the subnet of the network from which the OkiNet ut[...]

IV - 25 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Configuring TCP/IP Options T o configure options specific to the TCP/IP protocol, select the TCP/IP tab. The following screen will display: Fill in the following information: IP Address Resolution • Set Permanent - Select this option to make the IP address[...]

IV - 26 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide Subnet Mask If your network environment includes subnets, you will want to set the subnet mask. The subnet mask must follow the format XXX.XXX.XXX.XXX, where each XXX is a number from 0 to 255. The default subnet mask is 0.0.0.0. The OkiLAN 6100e+ interprets a subn[...]

IV - 27 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP T elnet/Http Password: Allows you to modify the current password required for T elnet or Http access. The default password is the serial number of the OkiLAN 6100e+. NetW are and NetW are Port Configuration Options For specific information on NetW are or Net[...]

IV - 28 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide EtherT alk Configuration Options T o modify the configuration settings specific to the EtherT alk protocol such as the name and zone. For specific information on EtherT alk options, see Section VII, EtherT alk , or select the HELP button on the bottom right of the [...]

IV - 29 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP • OFF - Print data stream will be sent directly to the output port without alteration. • PCL - Inserts the appropriate character string in front of each print job to switch the printer to the PCL print language. • PostScript - Inserts the appropriate c[...]

IV - 30 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide Output T ype Select the appropriate baud rate. Bidirectional Printer Status Support Enable this option for enhanced status from the bidirectional printer . SNMP Configuration Options SNMP options specify which information is necessary for an SNMP manger to access t[...]

IV - 31 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP System Contact Enter any information useful to a user if problems with the OkiLAN 6100e+ arise. System Location Enter a description of the OkiLAN 6100e+ location. Get Community Name This field is used to set the community name required to Get information fro[...]

IV - 32 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide Enabling/Disabling Protocols T o enable or disable protocols on the OkiLAN 6100e+, select the Protocols tab. Select each protocol you wish to enable. If you disable a protocol, the OkiLAN 6100e+ will no longer communicate using that protocol. SNMP T rap Configurati[...]

IV - 33 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Trap Destination • TCP/IP Protocol - Enter the IP address to which traps will be sent. The IP address must follow the format XXX.XXX.XXX.XXX, where each XXX is a number from 0 to 255. T o broadcast traps to all hosts on the local subnet, enter 255.255.255.[...]

IV - 34 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide Saving the Configuration Once all settings have been defined, select OK . The settings will be saved and you will be returned to the main OkiNet for TCP/IP screen. Displaying OkiLAN 6100e+ Diagnostic Information T o view OkiLAN 6100e+ diagnostic information, double[...]

IV - 35 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Restoring Factory Default Settings T o restore the OkiLAN 6100e+ to factory default settings, select the OkiLAN 6100e+ from the list of available print servers. From the Print Server menu bar , select Reset . From the Reset Print Server screen, choose one or[...]

IV - 36 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide Creating Customized Views OkiNet for TCP/IP allows users to create multiple customized views for the list of OkiLAN 6100e+ products. By creating different views, the user can narrow the information displayed to that which is of highest priority . These views can be[...]

IV - 37 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Modifying View Settings Before modifying the settings, select the name of the view you wish to edit from the Name field. Sort The Sort option displays the OkiLAN 6100e+ list in a specific order . The list can also be sorted by clicking on the column by which[...]

IV - 38 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide Search Filter The Search option defines the criteria for identifying OkiLAN 6100e+ products on the network. • Search Local Network - This method broadcasts a discovery request to locate all OkiLAN 6100e+ print servers on the local network. All OkiLAN 6100e+ print[...]

IV - 39 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP far left of the screen, follow these steps: 1. Select the first column in the Columns Displayed field. 2. Select the column to be added from the Columns A vailable field. 3. Select Add . Columns may also be removed by selecting Remove from the Columns A vail[...]

IV - 40 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide 6100e+. T o configure OkiNet for TCP/IP to use the correct community names, select Special Options from the File menu. IP Address This field displays the address of each OkiLAN 6100e+ for which OkiNet for TCP/IP has defined access. T o add a new IP address to this [...]

IV - 41 Section 4 - Chapter 4 - OkiNet for TCP/IP OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Configuring the Discovery UDP Port Number In order to discover OkiLAN 6100e+ print servers on the network, OkiNet for TCP/IP communicates with the OkiLAN 6100e+ print servers on a UDP port number . Normally , using this port number should not interfere with [...]

IV - 42 Section 4 - Chapter 5 - T elnet Configuration OKI OkiLAN 6100e+ User ’ s Guide Chapter 5 T elnet Configuration Overview The OkiLAN 6100e+ Configuration utility ( telnet ) provides system, network and printer status information and allows you to change the configuration of your OkiLAN 6100e+. Note: The configuration of your OkiLAN 6100e+ i[...]

IV - 43 Section 4 - Chapter 5 - T elnet Configuration OKI OkiLAN 6100e+ User ’ s Guide TCP/IP ***************************************** OkiLAN 6100e+ Configuration Utility 1. Show Network/Printer Information 2. Change Password 3. Specify Print Server IP Address 4. Specify Subnet Mask For Y our Network 5. Identify Default Gateway IP Address 6. Con[...]

IV - 44 Section 4 - Chapter 5 - T elnet Configuration OKI OkiLAN 6100e+ User ’ s Guide RARP or BOOTP server does not need to be available when the OkiLAN 6100e+ is powered on. If you change the IP address, the change will remain undetected until the OkiLAN 6100e+ is reset or is powered off and on. Remember , when choosing a permanent IP address: [...]

IV - 45 Section 4 - Chapter 5 - T elnet Configuration OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Identify Default Gateway IP Address (Option 5) If your local network is attached to other networks, you must specify the address of your default gateway . Whenever packets need to be sent to another network, the default gateway is used. The gateway addre[...]

IV - 46 Section 4 - Chapter 5 - T elnet Configuration OKI OkiLAN 6100e+ User ’ s Guide • Language Switching Sequence - If you select Custom Printer from the Configur e Printer T ype screen, you must indicate the switching sequence to be used for both PCL and PostScript. This is only necessary if language switching is set to something other than[...]

IV - 47 Section 4 - Chapter 5 - T elnet Configuration OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Restore to Factory Default Configuration (Option 9) This option automatically restores the OkiLAN 6100e+ to its original factory defaults. Be aware that when you restore the OkiLAN 6100e+ to the original factory default settings, only the TCP/IP protocol[...]

IV - 48 Section 4 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide Appendix A T roubleshooting Main Status Indicator Upon power-up, the main status indicator flashes orange. It changes to green when the OkiLAN 6100e+ passes self-test. The indicator stays orange if the OkiLAN 6100e+ fails self-test. If the indicator turns solid or[...]

IV - 49 Section 4 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Unable to Assign IP Address Gleaning If you ping the device and are not getting a response, the glean is not working. Check the following possible problems: • V erify the ARP table contains the correct hardware and IP address by running the ‘ arp -a ’[...]

IV - 50 Section 4 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide UNIX BOOTP If you are running UNIX, try the following methods with the BOOTP server (check the documentation for your particular UNIX flavor). • V erify the BOOTP server has reread the “/etc/ bootptab” file when the new entry was added. If the BOOTP server w[...]

IV - 51 Section 4 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Static Route Entry If the OkiLAN 6100e+ has printed a configuration page showing the default address, but it cannot be reached through telnet , check the following: • Display the host’ s routing tables with the ‘netstat - r ’ command. V erify the ro[...]

IV - 52 Section 4 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide OkiNet for TCP/IP - Winsock Errors • If you see an error before OkiNet for TCP/IP appears on the screen, try setting a host name in the hosts file in the W indows directory (check the documentation for your W indows TCP/IP stack). • If you have difficulty seei[...]

IV - 53 Section 4 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Printing a Configuration Page If the status indicator turns solid orange due to an error and no configuration page is printed, your printer may be configured for PostScript operation. If so, you must re-configure your printer for standard ASCII mode so that[...]

IV - 54 Section 4 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide • If the ftp succeeds, there is a problem with the lpr/ lp setup. V erify the hostname or IP address is correctly set for the queue. T ry doing an lpstat (System V) or lpq (BSD) to query the status of the OkiLAN 6100e+. FTP • If the indicator blinks green, the[...]

IV - 55 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Appendix B Application Considerations Overview This appendix provides application notes for the following: • Assigning the OkiLAN 6100e+ IP Address with BOOTP • Assigning the OkiLAN 6100e+ IP Address with RARP • Using the W indows NT v3.5 LPR[...]

IV - 56 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide (which may be a UNIX workstation) will respond with an IP address. The device will then know its IP address and use this address to perform subsequent TCP/IP transactions. Note: Once the OkiLAN 6100e+ has been assigned an IP address, the OkiLAN 6100e+ con[...]

IV - 57 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP A name can be arbitrarily assigned to any device on a network. The following examples use the name OKIPRINTER. Remember that this name is arbitrary; a customer can assign any name they wish. /etc/bootptab: The “/etc/bootptab” file has entries w[...]

IV - 58 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide 4. The bootpd daemon transmits a response to the OkiLAN 6100e+ with the IP address 192.168.42.55. The OkiLAN 6100e+ will use this IP address for all subsequent transmissions. For these steps to work properly , at least one BOOTP daemon (bootpd) must be ru[...]

IV - 59 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Configuring the OkiLAN 6100e+ IP Address with RARP RARP is an acronym for R everse A ddress R esolution P rotocol. Every TCP/IP network device must have a unique 32-bit IP address. TCP/IP network devices will have both an IP address and a 48-bit Et[...]

IV - 60 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide Configuration Files The purpose of RARP is to look up a 32-bit IP address given a 48-bit network hardware address. The RARP server (which is usually a UNIX workstation running a rarpd daemon) performs this function using two configuration files and one or[...]

IV - 61 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP 4. The rarpd then consults the “/etc/hosts” file and looks up the name OKIPRINTER. It finds an IP address (in this case 192.168.42.55) associated with the name OKIPRINTER. 5. The rarpd daemon transmits a response to the OkiLAN 6100e+ with the I[...]

IV - 62 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide Configuring HP-UX v8.07 for Printing with the OkiLAN 6100e+ This application note describes the configuration of the printing system on the HP-UX ver . 8.07 of the UNIX operating system. For clarity and brevity , the following specific names will be used [...]

IV - 63 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP 2. Make sure the rlp process is not running by typing at the UNIX prompt: ps -e | grep rlp If rlp is not running, you will not see any output after executing this command. If rlp is running (that is, if you see output after executing this command),[...]

IV - 64 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide 3. Select the following options, in order , from the SAM menu: Peripheral Devices -> Printers and Plotters -> Actions -> Add a Remote Printer (Do NOT select Add a Network Printer) A form appears asking you to define a remote printer . 4. Enter in[...]

IV - 65 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP 6. Enable the printer you just created using SAM. Peripheral Devices -> Printers and Plotters -> Enable a Printer ... 7. Printer name: — lj4 8. Start the LP request scheduler by typing: /usr/lib/lpsched 9. Run a test print job to the OkiLAN[...]

IV - 66 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide Prerequisites Before you proceed, the following prerequisites must be met. Most of the time steps 2 through 5 are already configured since the HP-UX system is on a TCP/IP network. Do not perform steps 2 through 5 unless the installation procedur e fails! [...]

IV - 67 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Procedure HP-UX uses an interactive utility called SAM (System Administration Manager) to configure printing. 1. Login to the HP-UX system as root. 2. Invoke the SAM utility by typing sam at the UNIX prompt. (W e suggest you do this at the system c[...]

IV - 68 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide h) Allow anyone to cancel r equests. Check if desired. i) Remote printer is on a BSD system. Check this box. T ells the HP-UX system that it is communicating with a Berkeley style remote printer (such as LPD). 5. Select the OK button. A status window will[...]

IV - 69 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP • yourqueuename - This is the name of the queue on the OkiLAN 6100e+ and must end with 1, 2, 3 or 4, depending on the port selected to service the print jobs. If FF , LF or NF are the last two letters of the queue name, the job will be converted [...]

IV - 70 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide 4. Make sure the following entry is in the “/etc/services” file: printer 515/tcp spooler 5. Start inetd by typing the following at the UNIX prompt: /etc/inetd -c Procedure HP-UX uses an interactive utility called SAM (System Administration Manager) to[...]

IV - 71 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP c) Remote printer name - yourqueuename This is the name of the queue on the OkiLAN 6100e+ and must end with 1, 2, 3 or 4, depending on the port selected to service the print jobs. d) Remote cancel model - rcmodel Used for remote printer job removal[...]

IV - 72 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide Configuring SCO UNIX for Printing with the OkiLAN 6100e+ This application note describes the configuration of the printing system on the Santa Cruz Operation’ s (SCO) version of the UNIX operating system. For clarity and brevity , the following specific[...]

IV - 73 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Procedure 1. Login to the SCO machine as root. 2. Install Remote Line Printing or verify that it is running by typing mkdev rlp at the UNIX prompt. It will respond by asking if you want to install or remove remote line printing. Choose Install even[...]

IV - 74 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide IBM’ s AIX ver . 3.x for Printing with the OkiLAN 6100e+ This application note describes the configuration of the printing system on IBM’ s AIX version 3.x of the UNIX operating system. The following specific names will be used to represent general de[...]

IV - 75 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP 3. T o add a remote queue, select the following options from the SMIT menu: Spooler (Print Jobs and Printers) Manage Remote Printer Subsystem Client Services Remote Printer Queues Add a Remote Queue A form appears asking you to define a remote prin[...]

IV - 76 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide 6. Start the qdaemon by typing: AIX> startsrc -s qdaemon 7. T ry printing to the printer attached to the OkiLAN 6100e+ by issuing the following command: AIX> lpr -Plj4 filename Configuring Solaris 2.x for Printing with the OkiLAN 6100e+ This applica[...]

IV - 77 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP Prerequisites Before you proceed, the following prerequisites must be met: 1. The name OKIPRINTER and the IP address assigned to the OkiLAN 6100e+ are in the “/etc/hosts” file on the Solaris system. 2. Make sure the LPD daemon is running on the[...]

IV - 78 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6100e+ This application note describes the configuration of the printing system on the Sun-OS ver 4.1.x and Ultrix ver . 4.2 of the UNIX operating system. For clarity and brevity , the [...]

IV - 79 Section 4 - Appendix B - Application Considerations OKI OkiLAN 6100e+ User ’ s Guide TCP/IP If the LPD daemon is running, you should see output similar to: root 135 0.0 0.0 52 0 ? IW May 24 0:01 /usr/lib/lpd If the LPD daemon is not running, start the daemon by logging into the Sun-OS or Ultrix machine as root and issuing the following co[...]

IV - 80 Section 4 - Appendix C - Internet Printing Pr otocol (IPP) OKI OkiLAN 6100e+ User ’ s Guide Appendix C Internet Printing Protocol (IPP) Internet Printing Protocol (IPP) is an application level protocol that can be used for distributed printing over the Internet. Using the new IPP protocol from any standard IPP client, you can print to any[...]

Banyan VINES Section V : Banyan VINES[...]

V - 2 Section 5 - Banyan VINES OKI OkiLAN 6100e+ User ’ s Guide In This Section Chapter 1 Introduction ........................................... V -3 Overview ....................................................... V -3 Before Y ou Start ............................................ V - 3 VINES Commands, Functions and Conventions ...............[...]

V - 3 Section 5 - Chapter 1 - Intr oduction OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES Chapter 1 Introduction Overview OkiLAN 6100e+ replaces a dedicated PC running PCPRINT . First, the OkiLAN 6100e+ logs on to the network as a user and opens a connection with a print service. The OkiLAN 6100e+ then accepts print jobs from a Banyan VINES serve[...]

V - 4 Section 5 - Chapter 1 - Intr oduction OKI OkiLAN 6100e+ User ’ s Guide VINES Commands, Functions, and Conventions Y ou should be familiar with the following VINES commands, functions, and conventions. See your Banyan VINES manuals for more information. StreetT alk StreetT alk is a global naming system. StreetT alk names are assigned to all [...]

V - 5 Section 5 - Chapter 1 - Intr oduction OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES Related Documents Y our printer manuals contain related information about printer configuration. Y our Banyan VINES manuals contain related information about network configuration and printing operation.[...]

V - 6 Section 5 - Chapter 2 - Installing the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide Chapter 2 Installing the OkiLAN 6100e+ Overview T o configure the network to access and use the OkiLAN 6100e+, follow these steps: • Install the OkiLAN 6100e+ (See Section I) Add a User to the Network for the OkiLAN 6100e+ • Create Print Services for th[...]

V - 7 Section 5 - Chapter 2 - Installing the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES 3. The Manage Users screen will appear . Select ADD a user . 4. The Add A User screen will appear . T ype in a Str eetT alk Name , Description , Nickname , and a Passwor d . Press F10 to save this information and continue. Note: Record and save[...]

V - 8 Section 5 - Chapter 2 - Installing the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide 5. The next screen is Add User Profile . The OkiLAN 6100e+ does not require any access rights while operating on the Banyan VINES network. T o maintain security on your network, we recommend you select a profile which grants no access rights to the user . I[...]

V - 9 Section 5 - Chapter 2 - Installing the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES Adding a Print Service The tasks involved in adding a print service are: • Adding and starting the service • Configuring the queue • Creating a list of paper formats • Setting up the access lists • Setting up the alert list • Adding[...]

V - 10 Section 5 - Chapter 2 - Installing the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide 4. The Add A Service screen will be displayed. Enter a Str eetT alk name and a Description for the print service and then press Enter to advance to the next screen. 5. Select a server . If multiple servers exist on your network, each will be listed. Make y[...]

V - 11 Section 5 - Chapter 2 - Installing the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES After making your selection, the following message will appear: The service is running but not yet available to users. For the service to be available, you must configure at least one destination. 8. T o configure the service, press F10 . Modi[...]

V - 12 Section 5 - Chapter 2 - Installing the OkiLAN 6100e OKI OkiLAN 6100e+ User ’ s Guide 14. The Print Queue Status screen will display . Y ou can now set up the print queue to accept print jobs. Respond YES to each question and press F10 . A message will appear , stating the print service is ready to accept print jobs. Press F10 to return to [...]

V - 13 Section 5 - Chapter 3 - The OkiNet for VINES Utility OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES Chapter 3 The OkiNet for VINES Utility Overview This section contains information about the OkiNet for VINES utility . OkiNet for VINES is also known as VPMAN. OkiNet for VINES is provided by OKI to configure and manage the OkiLAN 6100e+. Oki[...]

V - 14 Section 5 - Chapter 3 - The OkiNet for VINES Utility OKI OkiLAN 6100e+ User ’ s Guide Access Rights Y ou must have the appropriate access rights to use OkiNet for VINES. Access rights are based on group AdminLists comprised of StreetT alk names. T o perform administrative tasks, you must have membership to the associated AdminLists. If you[...]

V - 15 Section 5 - Chapter 3 - The OkiNet for VINES Utility OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES OkiNet for VINES Communication Options OkiNet for VINES options can be configured by selecting Startup from the Options pull-down menu. The following options are available: Hop count Number of hops OkiNet for VINES will broadcast searching fo[...]

V - 16 Section 5 - Chapter 3 - The OkiNet for VINES Utility OKI OkiLAN 6100e+ User ’ s Guide Configuring the Print Server 1. From the VINES Print Manager screen, select the OkiLAN 6100e+ you wish to configure. V erify the serial number on the screen matches the serial number on the OkiLAN 6100e+. The following Print Server Configuration screen wi[...]

V - 17 Section 5 - Chapter 3 - The OkiNet for VINES Utility OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES 3. Select Add Service to add a print service. Then, select the destination port of the OkiLAN 6100e+ to which the printer is connected. Once you have configured your print services, you may need to configure the printer port parameters. 4. Se[...]

V - 18 Section 5 - Chapter 3 - The OkiNet for VINES Utility OKI OkiLAN 6100e+ User ’ s Guide Saving Configuration Settings When you are satisfied with your configuration settings, select OK from the Configuration screen. This will save all changes and return you to the main menu. V erifying Communication T o verify communication, send a print job[...]

V - 19 Section 5 - Chapter 3 - The OkiNet for VINES Utility OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES Restore VINES Defaults Clears the Print Service names assigned and user name/ password. This does not af fect the configurations of other protocols. Restore Output Port Default Clears the output port configurations. This will af fect the prin[...]

V - 20 Section 5 - Chapter 3 - The OkiNet for VINES Utility OKI OkiLAN 6100e+ User ’ s Guide Configuring the TCP/IP Protocol T o configure options for the TCP/IP protocol, select TCP/IP Configuration from the Pr otocols menu from the Print Server Configuration screen. VPMAN will ask for the TCP/IP password. If a password has been set, type the pa[...]

V - 21 Section 5 - Chapter 3 - The OkiNet for VINES Utility OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES The IP address must follow the format XXX.XXX.XXX.XXX, where each XXX is a number from 0 to 255. If you change the IP address, the change will remain undetected until the OkiLAN 6100e+ is reset or powered off and on. Note: If you select an in[...]

V - 22 Section 5 - Chapter 3 - The OkiNet for VINES Utility OKI OkiLAN 6100e+ User ’ s Guide SNMP Options The SNMP configuration settings allow you to specify the SNMP community names and where SNMP T rap messages are to be sent. V iewing OkiLAN 6100e+ Status Information Y ou can view information about your network connection by selecting the Sta[...]

V - 23 Section 5 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES Appendix A T roubleshooting Unable to Print If your OkiLAN 6100e+ passes self-test, but you are unable to send data to the printer via the OkiLAN 6100e+, first try to print a configuration sheet from the OkiNet for VINES utility . If you are unable to [...]

V - 24 Section 5 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide Print server is not a destination for print service The PCPRINT StreetT alk name must match the name you assigned using the Destination Attributes screen when you configured the network to access and use the OkiLAN 6100e+. Problem communicating across network Indic[...]

V - 25 Section 5 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide Banyan VINES Print server not responding! The print server is not responding to the network call. The address may have changed. Select the Refresh button or exit OkiNet for VINES and try again. Set configuration failed, refresh window and try again The print server[...]

[...]

LAN Manager/ Server Section VI: LAN Manager/LAN Server[...]

VI - 2 Section 6 - LAN Manager/LAN Server OKI OkiLAN 6100e+ User ’ s Guide In This Section Chapter 1 Introduction .......................................... VI-3 Overview ...................................................... VI-3 System Requirements ................................... VI-3 Chapter 2 Installation .................................[...]

VI - 3 Section 6 - Chapter 1 - Intr oduction OKI OkiLAN 6100e+ User ’ s Guide LAN Manager/ Server Chapter 1 Introduction Overview This section contains information about the OkiNet for OS/2 utility . This utility allows you to install and configure the OkiLAN 6100e+ for your specific environment. The utility provides configuration information and[...]

VI - 4 Section 6 - Chapter 1 - Intr oduction OKI OkiLAN 6100e+ User ’ s Guide DLC/802.2 Protocol Stack The DLC/802.2 protocol stack must be loaded and running on the file server from which the OKI Network Printer Redirector will run. W ith LAN Manager , this means you must enable the remote boot facility . W ith LAN Server , you must select the 8[...]

VI - 5 Section 6 - Chapter 2 - Installation OKI OkiLAN 6100e+ User ’ s Guide LAN Manager/ Server Chapter 2 Installation Overview T o install the OkiLAN 6100e+: 1. Install the OkiNet for OS/2 utilities software. 2. Run the OkiNet for OS/2 utility to add a local printer port. 3. Associate a print queue with the new local printer port. Once the inst[...]

VI - 6 Section 6 - Chapter 2 - Installation OKI OkiLAN 6100e+ User ’ s Guide • The initial installation requires the file server to be brought down and then back up again. This may be a consideration when you are planning your install. Depending on your current configuration, the following software may also be needed: • Printer driver install[...]

VI - 7 Section 6 - Chapter 2 - Installation OKI OkiLAN 6100e+ User ’ s Guide LAN Manager/ Server Running INST ALL 1. Login to the server with administrator privileges. If you are reinstalling the utility , disable the spooler before running install. If this is the first time you have installed the utility , disabling the spooler is optional. 2. F[...]

VI - 8 Section 6 - Chapter 2 - Installation OKI OkiLAN 6100e+ User ’ s Guide 3. Select OK . The ESI Print Server Status Screen will display . From the Configur e menu, select Add Local Port . 4. Select a print server and port. Print servers are identified by serial number . (Y ou will find the serial number for your OkiLAN 6100e+ on the enclosure[...]

VI - 9 Section 6 - Chapter 2 - Installation OKI OkiLAN 6100e+ User ’ s Guide LAN Manager/ Server Creating an OS/2 Printer T o print to the local port created by OkiNet for OS/2, you must create an OS/2 printer . OS/2 1.3 1. Open the Print Manager from the desktop. 2. Select SETUP from the menu. 3. Select Printers . This will display a list of pri[...]

VI - 10 Section 6 - Chapter 2 - Installation OKI OkiLAN 6100e+ User ’ s Guide Printing a Configuration Sheet Y ou can verify communication by printing a configuration sheet using OkiNet for OS/2. 1. Select Configure from the main Print Server window . 2. Select Configure Print Server . 3. Select the OkiLAN 6100e+ you would like to test. 4. From t[...]

VI - 11 Section 6 - Chapter 3 - Printing in the OS2 Envir onment OKI OkiLAN 6100e+ User ’ s Guide LAN Manager/ Server Chapter 3 Printing in the OS/2 Environment Overview OS/2 provides several methods for selecting a printer from within an application. The best method to use depends on the specific application. The following methods are provided a[...]

VI - 12 Section 6 - Chapter 3 - Printing in the OS2 Envir onment OKI OkiLAN 6100e+ User ’ s Guide 3. Select the print queue associated with the OkiLAN 6100e+. OS/2 applications that use the default printer will now print to the printer attached to the OkiLAN 6100e+. The OS/2 print screen function uses the OS/2 default printer . This function is i[...]

VI - 13 Section 6 - Chapter 4 - Additional Utility Featur es OKI OkiLAN 6100e+ User ’ s Guide LAN Manager/ Server Chapter 4 Additional Utility Features Overview Y ou can run the OkiNet for OS/2 utility at any time to access the following optional features: • Deleting a Local Port • Configuring a Print Server Deleting a Local Port The delete c[...]

VI - 14 Section 6 - Chapter 4 - Additional Utility Featur es OKI OkiLAN 6100e+ User ’ s Guide 3. From the Configur e menu, select Configure Print Serve r . The following screen will display: The OkiLAN 6100e+ will reset by selecting OK to save any of the options, except the Print Configuration Sheet option. Configuring Parallel Port P1 Ports P1 a[...]

VI - 15 Section 6 - Chapter 4 - Additional Utility Featur es OKI OkiLAN 6100e+ User ’ s Guide LAN Manager/ Server Restoring Factory Defaults The Restore Defaults option restores the factory default settings for the LAN Manager/LAN Server protocol and output ports. T o restore factory defaults, select an OkiLAN 6100e+ from the list on the left. Th[...]

VI - 16 Section 6 - Chapter 5 - Using HELP OKI OkiLAN 6100e+ User ’ s Guide Chapter 5 Using Help Overview The OkiNet for OS/2 utility provides both general and context-specific help. General Help T o access help information about installation and configuration, select Help from the main menu, then select General Help . T o access help information[...]

VI - 17 Section 6 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide LAN Manager/ Server Appendix A T roubleshooting No Configuration Sheet If the LED turns solid orange due to a network protocol error and no configuration sheet is printed, your printer may be configured for PostScript operation. If so, you must re-configure your p[...]

[...]

EtherT alk Section VII: EtherT alk[...]

VII - 2 Section 7 - EtherT alk OKI OkiLAN 6100e+ User ’ s Guide In This Section Chapter 1 Introduction ......................................... VII-3 Overview .................................................... VII-3 System Requirements ................................. VII-3 Before Y ou Start ......................................... VII-3 Cha[...]

VII - 3 Section 7 - Chapter 1 - Intr oduction OKI OkiLAN 6100e+ User ’ s Guide EtherT alk Chapter 1 Introduction Overview This section describes the steps necessary to configure the EtherT alk protocol. The following topics are covered in this section: • Setting the Printer Name • Selecting a Zone • Selecting the Printer from the Macintosh [...]

VII - 4 Section 7 - Chapter 2 - The OkiLAN 6100e+ Utility OKI OkiLAN 6100e+ User ’ s Guide Chapter 2 The OkiLAN 6100e+ Utility Overview The OkiLAN 6100e+ utility allows the user to: • Change the OkiLAN 6100e+ product’ s AppleT alk Name • Move the OkiLAN 6100e+ from the Default Zone to a Preferred Zone • Print Configuration Page and view S[...]

VII - 5 Section 7 - Chapter 2 - The OkiLAN 6100e+ Utility OKI OkiLAN 6100e+ User ’ s Guide EtherT alk Renaming the OkiLAN 6100e+ Printer The OkiLAN 6100e+ Printer Selection window contains a list of all OkiLAN 6100e+ printers found in the selected zones. OkiLAN 6100e+ printers are listed alphabetically by name. Each port of a multiport OkiLAN 610[...]

VII - 6 Section 7 - Chapter 2 - The OkiLAN 6100e+ Utility OKI OkiLAN 6100e+ User ’ s Guide 4. Click OK . Print Configuration The Print Configuration option is accessed by selecting Print Config from the File pull-down menu. Choose this option to print an OkiLAN 6100e+ configuration sheet. A configuration sheet will print to all output ports. Stat[...]

VII - 7 Section 7 - Chapter 2 - The OkiLAN 6100e+ Utility OKI OkiLAN 6100e+ User ’ s Guide EtherT alk • T ype 2 (optional) - Select this option when configuring for a spooler . Enable Port This option allows you to enable or disable a port. If a port is disabled, it will appear in the OkiLAN 6100e+ utility but will not appear in the Chooser . A[...]

VII - 8 Section 7 - Chapter 2 - The OkiLAN 6100e+ Utility OKI OkiLAN 6100e+ User ’ s Guide Zone = Default - (The default zone for the network segment will be used) Port Enabled = Y es Appendix A T roubleshooting Before Y ou Call This appendix allows you to troubleshoot problems you may have installing or using the EtherT alk protocol. After tryin[...]

VII - 9 Section 7 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide EtherT alk • V erify that the OkiLAN 6100e+ has passed self-test. The status indicator should be solid green. • Check the connections between the OkiLAN 6100e+ and the Macintosh. When the OkiLAN 6100e+ does not appear in the Chooser , it is often caused by a c[...]

VII - 10 Section 7 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide document-specific. Check for problems in the document. If your printer has error handling capability , activate the error handler and try to print the first document again to obtain an error report. If the directory does not print, send the directory again, and w[...]

VII - 11 Section 7 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide EtherT alk appears in the Chooser . If not, refer to general EtherT alk troubleshooting. • V erify the Macintosh you are using is running Phase 2 EtherT alk. • Compare the zone in which the OkiLAN 6100e+ appears in the Chooser to the zones searched. Search th[...]

VII - 12 Section 7 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide Recommended Action: Unable to change the configuration at this time. T ry again. Message: “Name” @ “Zone” is not r esponding. V erify the OkiLAN 6100e+ is power ed on. T o reconnect with the device, r eturn the zone selection window and search again. Reco[...]

VII - 13 Section 7 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide EtherT alk or reset before it becomes idle, changes will be lost. Return to the zone selection window and search the network again to display the new information. Message: Ther e is not enough memory to perform the r equested action. Recommended Action: Closing w[...]

VII - 14 Section 7 - Appendix A - T r oubleshooting OKI OkiLAN 6100e+ User ’ s Guide Message: Unexpected AppleT alk error . Recommended Action: Check the network connection. T ry again. Appendix B Selecting Y our Printer T o Select Y our Printer 1. Click on the Apple in the menu bar and select Chooser . 2. Click on the Print Driver icon. If a cau[...]

VII - 15 Section 7 - Appendix B - Selecting Y our Printer OKI OkiLAN 6100e+ User ’ s Guide EtherT alk your printer is located. (Y ou may also need to scroll through the zones to locate the one you want.) If you do not know the zone in which your printer is located, contact your network administrator . 2. Click on the printer name you want to use.[...]

VII - 16 Section 7 - Appendix B - Selecting Y our Printer OKI OkiLAN 6100e+ User ’ s Guide Appendix C Capturing With a Spooler Overview T o use the OkiLAN 6100e+ with the AppleShare Print Server , follow these steps to capture the OkiLAN 6100e+. Capturing without Bypass Capturing 1. Use the OkiLAN 6100e+ utility and do the following: a) Change T [...]

Windows Printing Section VIII: Windows Printing[...]

VIII - 2 Section 8 - W indows Printing OKI OkiLAN 6100e+ User ’ s Guide In This Section Chapter 1 OkiLAN 6100e+ Set Up for Windows NT 4.0/2000 .......................................... VIII-3 Overview ................................................... VIII-3 OkiLAN 6100e+ Connect for IP ............... VIII-3 OkiLAN 6100e+ Connect for DLC .....[...]

VIII - 3 Section 8 - Chapter 1 - OkiLAN 6100e Setup for W indows NT 4.0 OKI OkiLAN 6100e+ User ’ s Guide Windows Printing Chapter 1 OkiLAN 6100e+ Set Up for Windows NT 4.0/2000 Overview This section contains instruction and information on how to set up your OkiLAN 6100e+ for a W indows NT 4.0/2000 environment. Print options for W indows NT 4.0/20[...]

VIII - 4 Section 8 - Chapter 1 - OkiLAN 6100e Setup for W indows NT 4.0 OKI OkiLAN 6100e+ User ’ s Guide Installation T o install OkiLAN 6100e+ Connect for TCP/IP , follow the instructions below: 1. Install the OkiLAN 6100e+ Connect for TCP/IP files - see Section I. 2. When installation is complete, click on Start , Settings and then Printers . 3[...]

VIII - 5 Section 8 - Chapter 1 - OkiLAN 6100e Setup for W indows NT 4.0 OKI OkiLAN 6100e+ User ’ s Guide Windows Printing 5. From the list of A vailable Printer Ports , select OKI OkiLAN 6100e+ Connect IP Monitor as the type of port to add and click New Port . Y ou will enter into the Add OkiLAN 6100e+ Connect Port screen where there will be a li[...]

VIII - 6 Section 8 - Chapter 1 - OkiLAN 6100e Setup for W indows NT 4.0 OKI OkiLAN 6100e+ User ’ s Guide Notify When Printed This feature will provide an alert when your job is active on the printer . This may be useful if the printer is especially busy . Description An optional field where you may list the location or other useful information ab[...]

VIII - 7 Section 8 - Chapter 1 - OkiLAN 6100e Setup for W indows NT 4.0 OKI OkiLAN 6100e+ User ’ s Guide Windows Printing Notify When Printed This feature will provide an alert when your job is active on the printer . This may be useful if the printer is especially busy . Description An optional field where you may list the location or other usef[...]

VIII - 8 Section 8 - Chapter 1 - OkiLAN 6100e Setup for W indows NT 4.0 OKI OkiLAN 6100e+ User ’ s Guide Install LPR Print Monitor 1. Open the W indows NT Control Panel . 2. Select the Services tab. 3. Select Add , then Micr osoft TCP/IP printing . 4. Click the Close button. 5. Restart the system. Assign Print Server IP Address 1. Using OkiNet fo[...]

VIII - 9 Section 8 - Chapter 1 - OkiLAN 6100e Setup for W indows NT 4.0 OKI OkiLAN 6100e+ User ’ s Guide Windows Printing 5. In the Name or addr ess of server pr oviding lpd: field, enter the IP address you assigned to the printer . 6. In the Name of printer or print queue on that server: field, enter the print server output port being used. For [...]

VIII - 10 Section 8 - Chapter 2 - OkiLAN 6100e Setup for W indows NT 3.51 OKI OkiLAN 6100e+ User ’ s Guide Chapter 2 OkiLAN 6100e+ Set Up for Windows NT 3.51 Overview This section contains information on setting up your OkiLAN 6100e+ for a W indows NT 3.51 environment. Print options for W indows NT 3.51 include: • OkiLAN 6100e+ Connect for IP ?[...]

VIII - 11 Section 8 - Chapter 2 - OkiLAN 6100e Setup for W indows NT 3.51 OKI OkiLAN 6100e+ User ’ s Guide Windows Printing files—see Section I. 2. From the W indows NT Print Manager Printer menu select Create Printer . 3. In the Cr eate Printer window select: • Printer Name • Driver • Description 4. At the Print prompt, select Other . 5.[...]

VIII - 12 Section 8 - Chapter 2 - OkiLAN 6100e Setup for W indows NT 3.51 OKI OkiLAN 6100e+ User ’ s Guide Using the Windows NT 3.51 LPR Print Monitor A Microsoft LPR print monitor is shipped with W indows NT 3.51. This print monitor is not included in the default W indows NT installation; therefore it will need to be installed. System Requiremen[...]

VIII - 13 Section 8 - Chapter 2 - OkiLAN 6100e Setup for W indows NT 3.51 OKI OkiLAN 6100e+ User ’ s Guide Windows Printing Assign Print Server IP Address Using OkiNet for IP , assign the print server an IP address; for example, 10.10.10.2. Note: For more information on using OkiLAN 6100e+ TCP/IP , see OkiNet for TCP/IP . Add LPR Printer 1. From [...]

VIII - 14 Section 8 - Chapter 3 - OkiLAN 6100e+ Setup for W indows 95/98 OKI OkiLAN 6100e+ User ’ s Guide Chapter 3 OkiLAN 6100e+ Set Up for Windows 95/98 Overview This section contains instruction and information on how to set up your OkiLAN 6100e+ for a W indows 95/ 98 environment. Print options for W indows 95/98 include: • OkiLAN 6100e+ Con[...]

VIII - 15 Section 8 - Chapter 3 - OkiLAN 6100e+ Setup for W indows 95/98 OKI OkiLAN 6100e+ User ’ s Guide Windows Printing 3. Select the W indows printer from which you would like to print with OkiLAN 6100e+ Connect, then select Pr operties from the File menu. 4. Add an OkiLAN 6100e+ Connect port. This may be done by selecting Add Port under the [...]

VIII - 16 Section 8 - Chapter 3 - OkiLAN 6100e+ Setup for W indows 95/98 OKI OkiLAN 6100e+ User ’ s Guide 8. Click OK . Y ou will now be able to use OkiLAN 6100e+ Connect for TCP/IP . Whenever you print to the printer configured with OkiLAN 6100e+ Connect, your print job will go directly to the OkiLAN 6100e+ print server port. Port Settings If yo[...]

VIII - 17 Section 8 - Chapter 3 - OkiLAN 6100e+ Setup for W indows 95/98 OKI OkiLAN 6100e+ User ’ s Guide Windows Printing 4. Add an OkiLAN 6100e+ Connect port. This may be done by selecting Add Port under the Details tab. 5. In the Add Port window , select the radio button labeled Other and select OKI OkiLAN 6100e+ Connect DLC Monitor as the typ[...]

VIII - 18 Section 8 - Chapter 3 - OkiLAN 6100e+ Setup for W indows 95/98 OKI OkiLAN 6100e+ User ’ s Guide Output Port Configuration Options T o configure the OkiLAN 6100e+ output port, select the Output Port tab. Port Number Select the port number you wish to configure. Configuration Page Language Select the appropriate printer language for print[...]

Regulatory Information Section IX: Regulatory Information[...]

IX - 2 Section 9 - Regulatory Information OKI OkiLAN 6100e+ User ’ s Guide Federal Communications Commission Radio Frequency Interference Statement This equipment generates and uses radio frequency energy . If not installed and used according to the manufacturer ’ s instructions, this equipment may cause interference with radio/TV reception. Th[...]

IR Printing Section X: IR Printing[...]

X - 2 Section X - IR Printing OKI OkiLAN 6100e+ User ’ s Guide In This Section Chapter 1: IR T ranceiver Features ........................ X-3 Specifications ................................................ X- 3 System Requirements .................................... X- 4 Chapter 2: Installation and Configuration ........... X- 5 Installing the [...]

X - 3 Section X - Chapter 1 - IR T ranceiver Features OKI OkiLAN 6100e+ User ’ s Guide IR Printing Chapter 1 IR T ranceiver Features The IR T ransceiver enhances the mobility of your portable device by allowing you to walk-up and connect to a printer equipped with an OkiLAN 6100e+ print server . The IR T ransceiver automatically detects and conne[...]

X - 4 Section X - Chapter 1 - IR T ranceiver Features OKI OkiLAN 6100e+ User ’ s Guide System Requirements · OkiLAN 6100e+ Print Server with infrared port connection. · Infrared port on notebook or mobile device meeting the IrDA standard. · Infrared print drivers on the mobile device. Infrared print drivers are provided through third parties f[...]

X - 5 Section X - Chapter 2 - Installation and Configuration OKI OkiLAN 6100e+ User ’ s Guide IR Printing Chapter 2 Installation and Configuration Installing the Hardware T o install the IR Transceiver , attach the DIN-6 connector on the back of the OkiLAN 6100e+ print server . General Information on Configuring Y our Print Server for IR If you w[...]

X - 6 Section X - Chapter 2 - Installation and Configuration OKI OkiLAN 6100e+ User ’ s Guide 6. For W indows 95 users only: Under the A vailable ports window , select either Infrar ed Printing (LPT) Port (recommended) or select the COM port labeled Infrared Serial (COM) Connections Port , then click Next . For W indows 98 users only: Under the A[...]

X - 7 Section X - Chapter 3 - Using the IR T ranceiver OKI OkiLAN 6100e+ User ’ s Guide IR Printing Chapter 3 Using the IR T ransceiver Position the infrared port of your portable computer or mobile device within three feet (one meter) of the IR T ransceiver ’ s infrared window , leaving an unobstructed path between the two units. Note: Palm, W[...]

[...]

Index Index A Access Rights OkiNet for VINES utility , V - 14 Advanced Configuration Options OkiLAN 6100e+ utility (EtherT alk), VII-6 Advanced Management Features HP OpenV iew , II-6 network alert, II-19 OkiNet for TCP/IP , II-20 printer security for TCP/IP Printing, II-20 security , II-5 Advanced management Features OkiNet for NDS, II-20 Assignin[...]

Index - 2 Index OKI OkiLAN 6100e+ User ’ s Guide Custom V iews creating in OkiNet for NetW are, III- 19 in OkiNet for TCP/IP , IV - 36 in TCP/IP , II-20 D Default Gateway IP Address identifying in telnet, IV -45 DHCP assigning an IP address, IV - 10 Diagnostic Information displaying in NetW are, III- 17 DLC/802.2 Protocol Stack, VI- 4 E Enabling/[...]

Index - 3 Index OKI OkiLAN 6100e+ User ’ s Guide Index H Hardware Installation, I-3 to I- 9 HP OpenV iew advanced management, II-6 HP-UX v10.xx Application prerequisites, IV -66 procedure, IV -67 HP-UX v8.07 Application prerequisites, IV -62 to IV -63 procedure, IV -63 to IV -65 HP-UX v9.xx Application Prerequisites, IV -66 procedure, IV -67 to I[...]

Index - 4 Index OKI OkiLAN 6100e+ User ’ s Guide O OkiLAN 6100e+ parallel output port signal assignments, I-15 print server status, I-10 OkiLAN 6100e+ Diagnostic Information displaying in OkiNet for TCP/IP , IV -34 OkiLAN 6100e+ Utility (EtherT alk) advanced configuration options, VII-6 enable port option, VII-7 error messages, VII-1 1 to VII-14 [...]

Index - 5 Index OKI OkiLAN 6100e+ User ’ s Guide Index OkiNet for VINES access rights, V -14 communication options, V - 15 configuring the print server , V -16 to V -17 configuring the TCP/IP protocol, V -20 to V -25 enabling/disabling proto- cols, V -19 installing, V -13 printing a configuration sheet, V -19 resetting the OkiLAN 6100e+, V -18 ru[...]

Index - 6 Index OKI OkiLAN 6100e+ User ’ s Guide Restoring Factory Default Settings in NetW are, III-18 in TCP/IP , IV -35 in VINES, V -18 RJ45 Pin Identification, I-14 Routers, VI-4 RPrinter Mode in NetW are, III- 5, III-8 S Sample Configuration Sheet, I- 12 to I-13 SCO UNIX Application prerequisites, IV -72 procedure, IV -73 Security in SNMP , [...]

Index - 7 Index OKI OkiLAN 6100e+ User ’ s Guide Index LAN Manager/LAN Server no configuration sheet, VI- 17 unable to print, VI-17 TCP/IP BOOTP , IV -49 FTP , IV -54 gleaning, IV -49 hardware error messages, IV -52 OkiNet for TCP/IP utility , IV -52 RARP , IV -49 restoring to factory defaults, IV -48 static route entry , IV -51 unable to assign [...]

Index - 8 Index OKI OkiLAN 6100e+ User ’ s Guide OkiNet for VINES utility access rights, V -14 communication options, V -15 configuring the print server , V -16 to V -17 installing, V -13 running, V -14 saving configuration settings, V -18 verifying communication, V -18 restoring the factory defaults, V -18 W W eb Configuration, II-11 to II- 18 A[...]