Onkyo TX-NR818 Bedienungsanleitung

E n AV RECEIVER TX-NR818 Instruction Manual Contents Safety Information and Introduction ............ 2 Table of Contents ............. .............. ........... ..... 6 Connections ....... .............. ........... .............. ... 13 Turning On & Basic Operati ons .................. 23 Advanced Operations .............. .............. ...[...]

En-2 Safety Information and Introduction Important Safety Instructions 1. Read these instruct ions. 2. Keep these instructi ons. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this a pparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilat ion openings. Install in accordance with the manuf acturer’s instruc[...]

Safety Information and Introduction En-3 Precautions 1. Recording Copyright —Unless it’s for personal use only, recording copyrighted ma terial is illegal without the permission of the copyright holder. 2. AC Fuse —The AC fuse inside the unit is not user- serviceable. If you cannot tu rn on the unit, contact your Onkyo dealer. 3. Care —Occa[...]

Safety Information and Introduction En-4 For Canadian Models NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. For models having a power co rd with a polarized plug: CAUTION: TO PREVENT ELECT RIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. Modèle pour les Canadien REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE B[...]

Safety Information and Introduction En-5 Supplied Accessories Make sure you have the following accessories: * In catalogs and on p ackaging, the letter at the end of the product name indicates the color. Specifi cations and opera tions are the same regardless of color. ■ Installing the batteries Note • If the remote controller doesn’t w ork r[...]

Safety Information and Introduction En-6 Table of Contents Safety Information and Intro duction Important Safety Instructions ......................................2 Precautions ................................................................... 3 Supplied Accessories......................... .......................... 5 Table of Contents .........[...]

Safety Information and Introduction En-7 Features Amplifier • 135 Watts/Channel @ 8 ohms (FTC) • 180 Watts/Channel @ 6 ohms (IEC) • 230 Watts/Channel @ 6 ohms (JEITA) • WRAT–Wide Range Amplifier Technology (5 Hz to 100 kHz bandwidth) • Linear Optimum Gai n Volume Circuitry • H.C.P.S. (High Current Po wer Supply) Massive High Power Tra[...]

Safety Information and Introduction En-8 Front & Rear Panels Front Panel (North American models) (European, Australian and Asian models) d e c f gh b a ij l m o p t q s n u w x y v k r z[...]

Safety Information and Introduction En-9 The AV receiver has various logos printed on it. They are not shown here for clarity. For detailed informat ion, se e the pages in parentheses. a 8 ON/STANDBY button ( 23 ) b Remote control sensor ( 5 ) c Display ( 10 ) d MASTER VOLUME control and indicator ( 26 ) e HYBRID STANDBY indicator ( 56 ) f PURE AUD[...]

Safety Information and Introduction En-10 s For detailed informat ion, se e the pages in parentheses. a Speaker/ channel indicat ors b Z2 (Zone 2) indicator ( 79 ) c Z3 (Zone 3) indicator ( 79 ) d Listening mode and format indicators ( 40 ) e M.Opt indicator ( 53 ) f 1 , 3 and cursor indi cators ( 28 ) g NET indicator ( 29 to 33 , 77 ) h Tuning ind[...]

Safety Information and Introduction En-11 a u REMOTE CONTROL jack b USB port c ETHERNET port d RS232 port Terminal for control. e Composite video and analo g audio jacks ( BD/DVD IN , CBL/SAT IN , STB/DVR IN , GAME 1 IN , PC IN , TV/CD IN and PHONO IN ) f HDMI IN and HDMI output ( HDMI OUT MAIN and HDMI OUT SUB ) jacks g COMPONENT VIDEO IN and MONI[...]

Safety Information and Introduction En-12 Remote Controller For detailed informat ion, se e the pages in parentheses. a 8 RECEIVER button ( 23 ) b ACTIVITIES buttons ( 50 ) c REMOTE MODE/INPUT SELECTOR buttons ( 26 ) d SP (speaker layout) button ( 49 ) e q / w / e / r and ENTER buttons f Q SETUP button ( 51 ) g Listening Mode buttons ( 40 ) h DIMME[...]

En-13 Connections Connecting the AV Receiver Speaker Configuration The following table indicates the channels you should use depending on the number of speakers that you have. No matter how many speakers you use, a powered subwoofer is recommended for a really p owerful and solid bass. To get the best from your surround sound system, you need to se[...]

Connections En-14 ■ 7.1-channel playback Select the speakers (surround back , front high, front wide ) you want to use for 7.1-channel playback. You can set which speakers you want to use by priority. See “Selecting Speaker Layout” ( ➔ page 49 ). Surround back left Surround left Surround right Front high left Front high right Front left Fro[...]

Connections En-15 Attaching the Speake r Cable Label s The speaker terminal s are color-coded for identification purpose. The supplied speaker cable labe ls are also color-coded and you should attach them to th e positive (+) side of each speaker cable in accordance with the table above. Then all you need to do is to match the color of each label t[...]

Connections En-16 Using Dipole Speakers You can use dipole speakers for the surround and surround back speakers. Dipole speakers output the same sound in two directions. Dipole speakers typica lly have an arrow printed on them to indicate how they should be positioned. The surround dipole speakers (a) should be positioned so that their arrows point[...]

Connections En-17 Connecting a Power Amplifier If you want to use a more po werful power amplifier, you can use the AV receiver as a preamp. Connect all speaker outputs to the power amplifie r. See the manuals supplied with your amplifier for details. SB ···Surround Back, FH ···Front High, FW ···Front Wide Note *1 Specify “ None ” for [...]

Connections En-18 Connecting AV components a *1 If your TV doesn ’t support Audio R eturn Channel (A RC), you need to connect an optical di gital cable together with the HDMI cable to the AV receiver. • Before making any AV connections, read the manuals supplied with your AV components. • Don’t connect the power cord until you’ve complete[...]

Connections En-19 * If your TV doesn’t suppo rt Audi o Return Channe l (ARC), you need to connect an optical digita l cable toge ther with the HDMI cable to the AV receiver. * When listening to an HDM I component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI[...]

Connections En-20 Connecting Your Components The on-screen menus appe ar only on a TV that is connected to HDMI OUT MAIN . If your TV is connected to other video outputs, use the AV receive r’s display when changing settings. C B A D A E F G H Front Rear GND screw Connect your components to the appropriate jacks. The default input assignment s ar[...]

Connections En-21 Note *1 Do not connect the AV receiver ’s USB port to a USB port on your computer. Music on your co mputer cannot be played through the AV receiver in this way. *2 Only the front-panel USB in put is compatible wit h iPod/iPhone. *3 When the USB input is selected, yo u can input video signals from the AUX INPUT VIDEO jack. Video [...]

Connections En-22 This section explains how to connect the s upplied indoor FM antenna and AM loop antenna. The AV receiver won’t pick up any radio signals without any antenna connected, so you must c onnect the antenna to use the tuner. Note • Once your AV receiver is ready for use, you’ ll need to tune into a radio station an d position the[...]

En-23 Turning On & Basic Operations Turning On/Off the AV Receiver Tip •T h e HYBRID STANDBY indicator may light depending on the status of settings ( ➔ pa ge 56 ). • For details on power management settings, see “Auto Standby” ( ➔ page 76 ). 8 RECEIVER RECEIVER 8 ON/ST ANDBY Turning On 1 Press 8 ON/STANDBY on the front panel. or Pr[...]

Turning On & Basic Operations En-24 Initial Setup This section explains the se ttings that we recommend you to make before using the AV receiver for the very first time. A setup wizard is launc hed upon first-time use to let you perform those settings. This step determines the la nguage used for the onscreen setup menus. See “ Language ” in[...]

Turning On & Basic Operations En-25 This step checks the connection of source components. W ith this step, you can enter remote control codes for the components you want to operate. This step checks your network connection. This step ends the initial setup proc ess. Source Connection 1 Use q / w to select one of the following options, and then [...]

Turning On & Basic Operations En-26 Playback ■ Operating with the remote controller ■ Operating on the AV receiver The on-screen inform ation ap pears only on a TV that is connected to HDMI outputs. If your TV is connected to other vid eo outputs, use the AV receiver’s disp lay wh en changing settings. This section describ es the procedur[...]

Turning On & Basic Operations En-27 Tip • See “Controlling Other Components” about the operation of other components ( ➔ page 84 ). Note • The buttons you can use will diff er depending on the devices and media used for playback. Controlling Contents of USB or Network Devices e k j m b a d f g c l n o h i q p Press USB or NET first. a[...]

Turning On & Basic Operations En-28 This section describes ic ons that appear on the AV receiver’s display during media playback. This section explains how to play music/video files on the iPod/iPhone. Compatible iPod/iPhone models Made for: iPod touch (1st, 2nd, 3rd and 4t h generation), iPod classic, iPod nano (2nd, 3rd, 4th, 5th and 6th ge[...]

Turning On & Basic Operations En-29 Extended Mode (Music) Cont rol The music content informati on is displayed (lists are displayed), and you can control the music content while looking at the screen. Top screen list: Playlists, Artists, Albums, Genres, Songs, Composers, Shuffle Songs, Now Playing. Note • In this mode, video contents are not [...]

Turning On & Basic Operations En-30 Internet radio URLs in the followi ng formats are supported: PLS, M3U, and podcast (RSS). However, depending on the type of data or audio format used by the Internet radio station, you may no t be able to listen to some stations. To listen to other Internet ra dio stations, you must register your station in ?[...]

Turning On & Basic Operations En-31 The layout of icons can be cu stomized by switching their positions on the network service screen. This section explains how to play music file s on a computer or media server thr ough the AV receiver (Server Playback). Windows Media Playe r 11 Setup This section explains how to configure Windows Media Player[...]

Turning On & Basic Operations En-32 Remote Playback means you can play the music files stored on a media server or personal computer with the AV receiver by operating the controller device in the home network. Windows Media Player 12 Set up This section explains how to configure Windows Media Player 12 so that the AV receiver can play the music[...]

Turning On & Basic Operations En-33 This section explains how to play music files on a computer or NAS (Network A ttached Storage) through the AV receiver. Windows 7 Setup ■ Setting the sharing options ■ Creating a shared folder Playing music file s on a shared folder In order to enjoy Home Media, you must first create a shared folder on yo[...]

Turning On & Basic Operations En-34 Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. You can store your favor ite stations as presets for quick selection. You can also change the frequency steps ( ➔ page 74 ). Tuning into Radio Stations ■ Auto tuning mod e ■ Manual tunin g mode In manual tuning mode, FM st a[...]

Turning On & Basic Operations En-35 ■ Selecting Presets ■ Deleting Presets Using RDS (excluding North American models) When tuned into an RDS station, the RDS indicator lights. When the station is broadcasti ng text info rmation, the text can be displayed. ■ What is RDS? RDS stands for Radio Data System and is a method of transmitting dat[...]

Turning On & Basic Operations En-36 ■ Listening to Traffic News (TP) You can search for stations that broadcast traffic news. RDS program types (PTY) You can listen to th e audio of one input source while watching the video of anot her. This function takes advantage of the fact that when an audio-only input source ( PC , TV/CD , PHONO ) is se[...]

Turning On & Basic Operations En-37 Using Basic Functions With the supplied calibrated microphone, Audyssey MultEQ ® XT32 automatically de termines the number of speakers connected, their size for purposes of bass management, optimum cro ssover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyss[...]

Turning On & Basic Operations En-38 1 Turn on the AV receiver and the connected TV. On the TV, select the input to which the AV r eceiver is connected. 2 Set the speaker setup microphone at the Main Listening Position a , and connect it to the SETUP MIC jack. The speaker setting menu appears. Note • The on-screen menus appear on ly on a TV th[...]

Turning On & Basic Operations En-39 Note • You can cancel Audyssey MultE Q XT32 Room Correction and Speaker Setup at any point in th is procedure simply by disconnecting the setup micr ophone. • Do not connect or disconn ect any speakers during Audyssey Mu ltEQ XT32 Room C o rrection and Speaker Setup. • If the AV rece iver is muted, it w[...]

Turning On & Basic Operations En-40 Selecting Listening Modes See “About Listening Modes” for deta iled information about the li st ening modes. ■ Listening Mode Buttons MOVIE/TV button This button selects the list ening modes intended for use with movies and TV. MUSIC button This button selects the list ening modes intended for use with [...]

Turning On & Basic Operations En-41 Input Source The following audio formats are supported by the listening modes. Speaker Layout The illustration shows which spea kers are activated in each channel. See “Speaker Configur ation” for the speaker setup ( ➔ page 60 ). *1 Press RECEIVER followed by SP (speaker layout) repeatedly to select the[...]

Turning On & Basic Operations En-42 ■ Onkyo-Original DSP Listening Modes Listeni ng Mode Description Input Source Speaker Layout Orchestra Suitable for classical or operatic music, this mode emphasizes the sur round channels in order to widen the stereo image, and simulates the natural reverberation of a large hall. A S D F G H CNM Unplugged [...]

Turning On & Basic Operations En-43 ■ Listening Modes Listeni ng Mode Description Input Source Speaker Layout Pure Au dio *1 In this mode, the display and video circuitry are turned off, minim izing possible noise sources for the ulti mate in high-fidelity audio reproduction. (As the analog video circuitry is turned off, on ly video signals i[...]

Turning On & Basic Operations En-44 Dolby Pro Logic IIx *7 Dolby Pro Logic II Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It prov ides a very natural and seamless surround- sound experience that fully envelops the listener. As well as music and movies, video games can also benefit from the dramatic spatial effects[...]

Turning On & Basic Operations En-45 • Dolby Pro Logic II/IIx *7 Movie + Audyssey DSX • Dolby Pro Logic II/IIx *7 Music + Audyssey DSX • Dolby Pro Logic II/IIx *7 Game + Audyssey DSX The combination of Dolby Pro Logic II/IIx and Audyssey DSX ® modes can be used. SB bM • Dolby Pro Logic IIx Movie + Audyssey DSX • Dolby Pro Logic IIx Mu[...]

Turning On & Basic Operations En-46 Note *1 Pure Audio cannot be selected when Z one 2/3 is active. Besides, if you activate Zone 2/3 while Pure Audio i s selected, the listening mode will automatically switch to Direct. *2 Based on the audio channel signal contained in the source, the correspond ing speakers will output the sound. *3 The AV re[...]

Turning On & Basic Operations En-47 The Home menu provides quick access to frequently used menus. ■ Network Service ` With this selection, you ca n use various Internet radio services or play the contents stored in media connected to your home network (DLNA) ( ➔ pages 29 to 32 ) . Note that this select ion will be grayed out for a short whi[...]

Turning On & Basic Operations En-48 With the sleep timer, you can set the AV receiver to turn off automatically aft er a specified period. You can adjust the brightness of the AV receiver’s display, and switch the MASTER VOLUME indicator off and on in conjunction. You can display various info rmation about the current input source as follows.[...]

Turning On & Basic Operations En-49 The Whole House Mode is us ef ul when you want to add extra background music to your home party; this allows you to enjoy the same stereo music as the main room in separate rooms (Zone 2/3). The Whole House Mode selects the same input source for Multi Zone as the main room’s. See also: • “Speaker Setup?[...]

Turning On & Basic Operations En-50 By using ACTIVITIES in Easy macro mode, you can sequentially operate Onkyo components via simple commands from a single-button press. These commands are user-definable. See “Us ing Normal Macros” ( ➔ page 90 ). ■ MY MOVIE First, the TV, the Onkyo DVD player, and the AV receiver are turned on. The inpu[...]

En-51 Advanced Operations On-screen Setup With the AV receiver connected to a TV, there are two ways of changing the settings on-screen: using the Quick Setup or the Setup menu ( HOME ). ■ Quick Setup The Quick Setup provides quick access to frequently used settings. You can change sett ings and view the current information. ■ Setup menu (HOME)[...]

Advanced Operations En-52 Note *1 • The video preview is not displayed when: – HDMI IN 5 / 6 / 7 is the current HDM I input source, or – No signal is present on the current input source. • The video of the currently-select ed input is displayed on the main screen, not on a preview thumbnail. *2 “ Dolby Vo lume ”, “ Dynami c EQ ” and[...]

Advanced Operations En-53 Dolby Volume ■ Dolby Volume See “Dolby Volume ” of “Audio Adjust” ( ➔ page 65 ). Note • This setting cannot be used in either of the f ollowing cases: – T he Pure Audio or Direct l istening mode is selected. – Any of the THX listening modes is selected, with “ Loudness Plus ” set to “ On ” or “ [...]

Advanced Operations En-54 Re-EQ With the Re-EQ function, you can compensate a soundtrack whose high-frequency content is too harsh, making it more suitable fo r home theater viewing. ■ Re-EQ ` Off ` On This function can be used wi th the following listening modes: Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Multichannel, DTS, DTS- HD High Re[...]

Advanced Operations En-55 Note • This procedure can also be performed on the AV receiver by using SETUP , the cursor and enter (middle) buttons. • During Audys sey MultEQ ® XT32 Room Correction and Speaker Setup, messages, etc., that are displaye d on the TV screen will appear on the AV rece iver’s display. Explanatory Notes a Main Menu b Su[...]

Advanced Operations En-56 By way of optimized circuitry, this fu nction reduces power consumption when the AV rece iver is in standby mode. The HYBRID STANDBY indicator will li ght in either of the following conditions: –“ HDMI Th rough ” is enabled (the HDMI indicator is off). –“ Network Standby ” is enabled (the NE T indicator is off)[...]

Advanced Operations En-57 Main Menu Input/Output Assi gn Monitor Out On the “ Monitor Out ” settings, you can se lect whether or not to hav e the video sour ces’ images output through the HDMI output. If you connect your TV to the HDMI output, the “ Monitor Out ” setting is automatically set and composite video and component video sources[...]

Advanced Operations En-58 HDMI Input If you connect a video compone nt to an HDMI input, you must assign that input to an i nput selector. For example, if you connect your Blu-ray Disc/DVD player to HDMI IN 2 , you must assign “ HDMI2 ” to the “ BD/DVD ” input selector. If you’ve connected your TV to the AV receiver with an HDMI cable, co[...]

Advanced Operations En-59 Digital Audio Input If you connect a component to a digital audio input, you must assign that input to an i nput selector. For example, if you connect your CD player to the OPTICAL IN 1 , you must assign “ OPTICAL1 ” to the “ TV/CD ” input selector. Here are the d efault assignments. ■ BD/DVD , CBL/SAT , STB/DVR,[...]

Advanced Operations En-60 Note • If the “ Speakers Type (Front) ” setting is set to “ Bi-Amp ” or “ Digital Crossover ”, Powered Zone 2 cannot be used. •W h e n t h e “ Powered Zone 2 ” setting is set to “ Yes ” and Zone 2 is turned on, the s urround back and front h igh speakers cannot be used. • If the “ Powered Zone 2[...]

Advanced Operations En-61 ■ Double Bass ` On ` Off(THX) Turn this setting on to boos t bass output by feeding bass sounds from the front left, ri ght, and cen ter channels to the subwoofer. Note •W h e n t h e “ Subwoofer ” setting is set to “ No ” or the “ Front ” setting to anything other than “ Full Band ”, this setting is fi[...]

Advanced Operations En-62 Equalizer Settings With the Equalizer settings, you can adjust the tone of speakers individually with a 7-band equalizer. The volume of each speaker ca n be set ( ➔ page 61 ). ■ Manual Equalizer ` On : You can adjust the equalizer for each speaker manually. Continue with the following procedure: ` Off : Tone off, respo[...]

Advanced Operations En-63 Digital Processing Crossover Network Digital Crossover provides a separate routing system by splitting the audi o signal into separate fr equency bands optimized for each speaker driv er. It provides a fine, three- dimensional sound field that extend each driver’s performance to the uppermost. With its built-in time alig[...]

Advanced Operations En-64 ■ High Dist ance, Lo w Distanc e ` 0inch(0.0cm) to 12inch(30.0cm) in 1 inch(2.5 cm) steps With this setting, you can ad just the virtual position of tweeter and woofer units. Adjusting “ High Distance ” virtually shifts woofers be hind tweeters. Adjusting “ Low Distance ” virtually shifts tw eeters behind woofers[...]

Advanced Operations En-65 Center Width ` 0 to 3 to 7 With this setting, you can ad just the width of the so und from the center speaker when using the Dolby Pro Logic IIx Music listening mode. Normally, if y ou’re using a center speaker, the center channel sound is output from only the center speaker. (If you’re not using a center speaker, the [...]

Advanced Operations En-66 DTS ■ Neo:X Music Center Image ` 0 to 2 to 5 The DTS Neo:X Music listeni ng mode creates 9-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenua ted in order to cre ate the center channel. Changing the value from “0” to [...]

Advanced Operations En-67 The “ Straight Decode ” option means that straight decoding listening mode ( Dol by Digital, DTS, etc.) is selected. ■ Subwoofer ` No , Yes You can choose whether or not to use the subwoofer with the sound program. ■ Music Optimizer *1 ` Off , On See “Music Optim izer” ( ➔ page 53 ). ■ Equalizer *1 ` Off ` [...]

Advanced Operations En-68 Movies are mixed in rooms ca lib rated for film reference. To achieve the same referenc e level in a home theater system each speaker level must be adjusted so that –30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home t heater system aut omatically ca [...]

Advanced Operations En-69 Name Edit You can enter a custom name for each individual in put selector and radio preset for easy identifi cation. When entered, the custom name will app ear on the display. The custom name is edited using the keyboard screen. ■ Name Tip • To name a radio preset, use TUNER to select AM or FM , and then select the pre[...]

Advanced Operations En-70 ■ Picture Mode *1*3 ` Custom : All settings can be performed manually. ` ISF Day : Select when the room is bright. ` ISF Night : Select when the room is dark. ` Cinema : Select when the picture source is a mov ie or alike. ` Game : Select when t he video s ource is a game console. ` Streaming : Attempts to reduce the mo [...]

Advanced Operations En-71 ■ Resolution *4*6*8 ` Through : Select this to pass video through the AV receiver at the same resolution and with no conversion. ` Auto : Select this to have the AV receiver automat ically convert video at resolutions supported by your TV. ` 480p ( 480p/576p ), 720p , 1080i , 1080p : Select the desired output resolution.[...]

Advanced Operations En-72 Audio Selector ■ Audio Selector ` ARC : The audio signal from your TV tuner can be sent to HDMI OUT MAIN of the AV receiver. *1 With this selection, the TV’s audio can be automatically selected as a priority among other assignments. ` HDMI : This can be selected when HDMI IN has been assigned as an input source. If bot[...]

Advanced Operations En-73 ■ Analog/PCM/Digital With this setting, you can specify the listening mode used when an analog (CD, TV, LD, VHS, MD, turntable, radio, cassette, cable, satellit e, etc.) or PCM digital (CD, DVD, etc.) audio signal is played. Note •F o r t h e “ GAME2 ” input selector, only “ PC M ” is available. ■ Mono/Multip[...]

Advanced Operations En-74 ■ Power On Volume ` Last , Mi n , 1 to 99 or Max (Absolute display) ` Last , – Q dB , –81dB to +18dB (Relative display) With this preference, you can specify the volume setting to be used each time the AV rece iver is turned on. To use the same volume level that was used when the AV receiver was turned off, select ?[...]

Advanced Operations En-75 HDMI ■ HDMI Control(RIHD) ` Off ` On Turn this setting on to allow p -compatible components connected via HDM I to be controlled by the AV receiver ( ➔ page 104 ). Note • When the setting is set to “ On ” and the menu is closed, the names of connected p -compatible components and “ RIHD On ” are displayed on [...]

Advanced Operations En-76 ■ Audio Return Channel (ARC) ` Off ` Auto : The audio signal from your TV tuner can be sent to HDMI OUT MAIN of the AV receiver. The audio return channel (ARC) f unction allows an ARC capable TV to send the audio stream to HDMI OUT MAIN of the AV receiver. To use th is function, you must select the TV/CD input selector a[...]

Advanced Operations En-77 ■ DHCP ` Enable ` Disabl e This setting determines whet her or not the AV receiver uses DHCP to automatical ly configure its IP Address, Subnet Mask, Gateway, a nd DNS Server settings. Note • If you select “ Disable ”, you must conf igure the “ IP Address ”, “ Subnet Mask ”, “ Gate way ”, and “ DNS Se[...]

Advanced Operations En-78 Multi Zone In addition to the main liste ning room, you can also enjoy playback in the other room, or as we call Multi Zone. And, you can select a different source for each room. There are two ways you ca n connect Zone speakers: 1. Connect them directly to the AV receiver. 2. Connect them to an additional amplifier. Conne[...]

Advanced Operations En-79 Connecting the Zone Speaker s to an Additional Amplifier This setup allows 7.1-cha nnel playback in your main listening room and 2-channel stereo playback in Zone 2/3. Note • The volume of Zone 2/3 must be set on the Zone 2/3 amplifier. ■ Operating on the AV receiver Tip • The Whole House Mode function shares the inp[...]

Advanced Operations En-80 Adjusting the Volume for Zones ■ Operating on the remote controller ■ Operating on the AV receiver If your Zone 2/3 speakers are co nnected to a receiver or integrated amplifier in Zone 2/3, use its volume control to adjust the volume. Muting Zones ■ Operating on the remote controller Tip • To unmute, pr ess ZONE f[...]

Advanced Operations En-81 To control the AV re ceiver with the remote controller while you’re in Zone, you’ll ne ed a commercially available multiroom remote contro l kit for each zone. • Multiroom kits are made by Niles and Xantech. These kits can also be used when there isn’t a clear line of sight to the AV receiver’s rem ote sensor, su[...]

En-82 Controlling Other Components iPod/iPhone Playback via Onkyo Dock RI Dock With the RI Dock, you can easily play the music of your iPod/iPhone, or watch the slid eshows and videos of your iPod/iPhone on a TV. In addition, the on-screen display (OSD) allows you to view, navigate, and select your iPod/iPhone model’s contents on your TV, and wit[...]

Controlling Other Components En-83 By pressing the REMOTE MODE button that’s been programmed with the remote control code for your Dock, you can control your iPod/iPhone in the Dock with the buttons described further in this section. See “Entering Remote Control Codes” for details on entering a remote control code ( ➔ page 85 ). See the Doc[...]

Controlling Other Components En-84 Controlling Other Components You can use the AV receiver’s remot e controller to cont rol your other AV components. This section explains how to enter the remote control code for a component that you want to control : DVD, TV, CD, etc. See “Learning Commands ” for learning commands directly from another comp[...]

Controlling Other Components En-85 You’ll need to enter a code for each component that you want to control. Note • Though the prov ided remote cont rol codes are correct at the time of release, they are subject to change. You can change the configuration of colored b uttons, with which REMOTE MODE buttons are preset. Tip • To reset the REMOTE[...]

Controlling Other Components En-86 Onkyo components that are connected via u are controlled by pointing the re mote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example. Controlling Onkyo co mponents without u If you want to control an Onkyo component by pointing the re[...]

Controlling Other Components En-87 Controlling MHL-Enabled Mobile De vice By programming the supplied re mote controller with the appropriate remote control code, you can use it to operate your MHL-enabled mobile device. Connect your MHL-enabled mobile device to the AUX INPUT MHL jack. We advise you to program the remote control code on the AUX but[...]

Controlling Other Components En-88 ■ DVD player/DVD reco rder operation ■ VCR/PVR operation ■ Cassette tape deck operation ■ Satellite receiver/Cable receiver oper ation ■ CD player/CD recorder/MD recorder operation Note • With some components, certain buttons may not work as expected, and some may not work at all. • See “Controllin[...]

Controlling Other Components En-89 The AV receiver’s remote controller can lear n the commands of other remote con trollers. By transmittin g, for example, the Play command fro m your CD player’s remote controller, the supplied remote controller can learn it and then reproduce the exact sam e command when its 1 is pressed in CD remote mode. Thi[...]

Controlling Other Components En-90 You can program the re mote controller’s ACTIVITIES to perform a sequence of re mote control actions. Example: To play a CD you typically need to perform the following actions: 1. Press RECEIVER to sele ct the Receiver rem ote controller mode. 2. Press 8 RECEIVER to turn on the AV receiver. 3. Press TV/CD to sel[...]

En-91 Appendix Troubleshooting If you have any trouble using th e AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact your Onkyo dealer. ■ Can’t turn on the AV receiver ■ The AV receiver turns off unexpectedly ■ The AV receiver turns o ff and after restoring the power, it turns off again ■ [...]

Appendix En-92 ■ Only the front speakers produce sound ■ Only the center sp eaker produces sound ■ The surround speakers produce no sound ■ The center speaker produces no sound ■ The front high, front wi de and surround back speakers produce no sound ■ The subwoofer pr oduces no sound ■ There’s no sound w ith a certain signal format[...]

Appendix En-93 ■ About DTS signals ■ The beginning of audio received by an HDMI IN can’t be hea rd ■ There’s no sou nd during Whole Hou se Mode ■ There’s no picture ■ There’s no picture from a source connected to an HDMI IN ■ The on-screen me nus don’t appear ■ The on-screen informa tion does not appear ■ Reception is nois[...]

Appendix En-94 ■ Can’t control oth er components ■ Can’t learn commands from another remote controller ■ There’s no sound ■ There’s no video ■ The AV receiver’s remo te controller doesn’t control my iPod/iPhone ■ The AV receiver unexp ectedly selec ts my iPod/iPhone as the in put source ■ iPod/iPhone does n’t work proper[...]

Appendix En-95 ■ Can’t connect to the AV receiver fr om a Web browser ■ Can’t access the music files on a U SB device ■ Standby power consumptio n ■ The sound changes wh en I connect my headphones ■ The speaker distance cann ot be set as required ■ The display doesn’t work ■ How do I change the l anguage of a multip lex source ?[...]

Appendix En-96 ■ If the picture on your TV/monitor connected to the HDMI output is unstable, try switchin g the DeepColor function off To turn off the DeepColor function, simu ltaneously press the STB/DVR and 8 ON/STANDBY buttons on the AV receiver. While holding down STB/DVR , press 8 ON/STANDBY until “ Deep Color:Off ” appears on the AV rec[...]

Appendix En-97 Firmware Update To update the firmware of the AV receiver, you can choose from the following two methods: update via network, or update via USB storage. Choose the one that best suits your environment. Before pr oceeding with the update, please read the correspondi ng explanations carefully. ■ Update via network You need a wired In[...]

Appendix En-98 Update Procedure Troubleshooting Case 1: If an error occurs, “ Error!! *-** ” is displayed on the AV receiver’s display. (Alpha-num eric characters on the front display are denoted by asterisk s.) Refer to the following table and take a ppropriate action. ■ Errors during an update via netwo rk Case 2: If an error occurs durin[...]

Appendix En-99 The AV receiver allows you to update the firmware using a USB device. Note • Never unplug or turn off the AV receiver duri ng the update process. • Never plug or unplug an HDMI cable o r a USB device during the update process. • Never unpl ug the USB stor age device containi ng the firmware file or the AC power cord during the [...]

Appendix En-100 Troubleshooting Case 1: If an error occurs, “ Error!! *-** ” is displayed on the AV receiver’s display. (Alpha-numeric ch aracters on the front display are denoted by asterisk s.) Refer to the following table and take appropriate action. ■ Errors during an update via USB Case 2: If an error occurs during the update process, [...]

Appendix En-101 Connection Tips and Video Signal Path The AV receiver supports seve ral connection formats for compatibility with a wi de ra nge of AV equipment. The format you choose will depe nd on the formats supported by your components. Use the foll owing sections as a guide. Video components can be c onnected by using any one of the following[...]

Appendix En-102 ■ Signal Selection If signals are present at more than one input, the inputs will be selected automatically in t h e following order of priority: HDMI, component vide o, composite video. However, for component video only, regardless of whether a component video signal is actually present, if a component video input is assi gned to[...]

Appendix En-103 The following tables show how vide o signals at differe nt resolutions are output by the AV receiver. NTSC/PAL ✔ : Output available s *1 Available resolutions: [640 × 480 60 Hz], [800 × 600 60 Hz], [1024 × 768 60 Hz], [1280 × 1024 60 Hz] *2 Supported resolutions: [3840 × 216 0 24/25/30 Hz], [4096 × 2160 24 Hz] *3 When video [...]

Appendix En-104 Using an RIHD- compatible TV, Player, or Recorder p , which stands for Re mote Interactiv e over HDMI, is the name of the system control function found on Onkyo components. The AV rece iver can be used with CEC (Consumer Elec tronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides inter[...]

Appendix En-105 ■ How to connect and setup 1 Confirm the connection and s ettings. 1. Connect the HDMI OUT MAIN jack to the HDMI input jack of the TV. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note • When the audio return channel (ARC) function is used with an ARC capable[...]

Appendix En-106 About HDMI Designed to meet the increa sed demands of di gital TV, HDMI (High Definition Multimedia Interfac e) is a new digital interface standard fo r co nnecting TVs, projectors, Blu-ray Disc/DVD players, se t-top boxes, and other video components. Until now, severa l separate video and audio cables have been required to connect [...]

Appendix En-107 Network/USB Features The following diagram shows how you can connect the AV receiver to your home network. In this example, it’s connected to a LAN port on a router, which has a 4-port 100Base-TX switch built-in. ■ Ethernet Networ k For the best results, a 100B ase-TX switched Ethernet network is recommended. Although it’s pos[...]

Appendix En-108 ■ Server playback The AV receiver ca n play digital music files stored on a computer or media server and supports the following technologies: • Windows Media Player 11 • Windows Media Player 12 • Windows Media Connect 2.0 • DLNA-certified media server If the operating system of your computer is Windows Vista, Windows Media[...]

Appendix En-109 For server playback and pla yback from a USB device, the AV receiver supports the fo llowing music file formats. Variable bit-rate (VBR) file s are supported. However, playback times may not display correctly. Note • With remote playback, the AV receiver does not support the following music file formats: FLAC and Ogg Vorbis. • I[...]

Appendix En-110 License and Trademark Information “x.v.Color” is a trademark of Sony Corporation. Manufactured under license und er U.S. Patent No's: 5,956,674, 5,974,380, 5,978,762, 6, 487,535, 6 ,226,616, 7,212 ,872, 7,003,467, 7,272,567, 7, 668,723, 7 ,392,195, 7,333 ,929, 7,548,853 & othe r U.S. and worldwide patents issued and pen[...]

Appendix En-111 Specifications Amplifie r Section Video Section Tuner Section General ■ HDMI ■ Video Inputs ■ Video Outputs ■ Audio Inputs ■ Audio Outputs ■ Others Specifications and featu res are subject to change without notice. Rated Output Power All channel s: (North Am erican) 135 watts mini mum continuous power per channel, 8 oh m[...]

2-1, Nisshin-cho , Ney aga wa-shi, OSAKA 572-8540, J AP AN T el: 072-831-8023 F ax: 072-831-8163 http://www .onkyo .com/ 18 P ark W a y , Upper Saddle River , N.J. 07458, U.S .A. T el: 800-229-1687, 201-785-2600 F ax: 201-785-2650 http://www .us.onkyo .com/ Liegnitzerstrasse 6, 82194 Groebenz ell, GERMANY T el: +49-8142-4401-0 F ax: +49-8142-4208-2[...]

Using Internet Radio En-1 Using Internet Radio Note • Available services may vary depending on the r egion. Common Procedures in Internet Radio Menu 1 Press NET . A list of the network serv ices appears, and the NET indicator lights. If it flashe s, verify that the Ethernet cable is firmly connected to the AV receiver. 2 Select the des ired servi[...]

Using Internet Radio En-2 Pandora is a free, personalized Internet radio service that plays the music you know and helps you discover music you’ll love. PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks or regi stered trademarks of Pandora Media, Inc. Used with permission. Pandora ® internet radio –Getting Started (U.S. onl[...]

Using Internet Radio En-3 Using Rhapsody (U.S. only) 1 Use q / w to select “Sign in to your account” and then press ENTER . To use Rhapsody, you need an acco unt. If you don’t have one yet, you can create a new account at www.rhapsody.com/onkyo If you have an existing Rhapsody account, select “ Sign in to your account ” and press ENTER . [...]

Using Internet Radio En-4 Your Onkyo AV receiver includes a free trial of SiriusXM Internet Radio. The “Account Info” screen shows how many days are left in your trial. After the trial period expires, if you want to conti nue listening to the service, you must subscribe. To subscribe go to www.siriusxm.com /internetradio with your computer. Whe[...]

Using Internet Radio En-5 Last.fm is a music s ervice th at learns what you love... Your new Onkyo AV receiver is very clever. If you have a free Last.fm account, it will keep track of all the songs you’ve just played. When you visit the Last.fm website, you can see personal charts of the music you’ve enjoyed, share them with friends and see wh[...]

Using Internet Radio En-6 Using Slacker Personal Radio 1 If you do not have an ac count, create one on the Slacker website (www.sl acker.com) with your computer. If you already have a Slac ker account, se lect “Sign in to your account” and then press ENTER . The keyboard screen appears. You can enter information from the remote control or the k[...]

Using Internet Radio En-7 Listen to your music collection on your home stereo in complete digital fide lity wit hout a p ersonal computer plus safely backup all your songs. Here’s how: Creating an Account on your Computer Playing Contents on the AV Receiver Tip • Before proceeding, you need to select the MP3tunes service as described in “Com [...]

Utilisation d’une webradio Fr-1 Utilisation d’une webradio Remarque • Les services disponibles peuvent varier en fonction de la région. Procédures courantes dans le menu de webradio 1 Appuyez sur NET . Une liste des services réseau s’affiche, et le témoin NET s’allume. S’il clignote , vérifiez que le câble Ethernet est f ermement [...]

Utilisation d’une webradio Fr-2 Pandora est un service de radio en ligne libre et personnalisé vous permettant de lire la musique que vous connaissez et de découvrir celle que vous aimez. PANDORA, le logo PANDOR A, et l’habillage commercial Pandora sont des marques commerciales ou des marques dépo sées de la société Pandora Media, Inc. Ut[...]

Utilisation d’une webradio Fr-3 Utilisation de Rhapsody (Etats-Unis uniquement) 1 Utilisez q / w pour sélec tionner « Sign in to your account », puis appuyez sur ENTER . Vous devez posséder un compte pour utiliser Rhapsody. Si vous ne di sposez pas encore d’un compte, vous pouvez en créer un à partir de www.rhapsody.com/onkyo Si vous poss[...]

Utilisation d’une webradio Fr-4 Votre ampli-tuner AV Onkyo co mprend un essai gratuit de SiriusXM Internet Radio. L’ écran « Account Info » affiche le nombre de jours restants da ns votre essai. Une fois la période d’essai expirée, si vous souhaitez continuer à écouter le service, vous de vez vous abonner. Pour vous inscrire, accé dez[...]

Utilisation d’une webradio Fr-5 Last.fm un service de musique qui appr end ce que vous aimez… Votre nouvel ampli-tuner AV O nkyo est très intelligent. Si vous avez un compte Last.fm gr atuit, il garde une trace de toutes les chansons que vous avez juste jouées. Quand vous vous rendez sur le site Web de Last.fm, vous pouvez voir les graphiques[...]

Utilisation d’une webradio Fr-6 Utilisation de Slacker Personal Radio 1 Si vous ne possédez pas de compte, c réez-en un à partir du site Web de Slacker (www.slacker.com) à l’aide de votre ordinateur. Si vous possédez déjà un compte Slacker, sélectionnez « Sign in to your account », puis appuyez sur ENTER . L’écran clavier s’affic[...]

Uso de In ternet Radio Es-1 Uso de Internet Radio Nota • Los servicios disponibles pueden variar de una regió n a otra. Procedimientos comunes en el menú Internet Radio 1 Pulse NET . Aparecerá una lista de los servicios de red y se iluminará el indicador NET . Si parpadea, verifique que el cable Ethernet esté firmem ente conectado al recepto[...]

Uso de In ternet Radio Es-2 Pandora es un servicio de radi o por Internet gratuito y personalizado que reproduce la música que usted conoce y le ayudará a descubrir mú sica que le encantará. PANDORA, el logotipo de PANDORA logo, y la imagen corporativa de Pandora son ma rcas comer ciales o marcas comerciales registradas de Pandora Media, Inc. U[...]

Uso de In ternet Radio Es-3 Uso de Rhapsody (sólo EE.UU.) 1 Utilice q / w para sel eccionar “Sig n in to your account” y luego pulse ENTER . Para utilizar Rhapsod y, necesitará una cuenta . Si todavía no tiene una, puede crear una nueva en www.rhapsody.com/onkyo Si ya tiene una cuenta Rhapsody, seleccione “ Sign in to your account ” y pu[...]

Uso de In ternet Radio Es-4 Su receptor de AV Onkyo incl uye una prueba gratuita de SiriusXM Internet Radio. La pantalla “Account Info” muestra los días que quedan de la prueba. Una vez que termine el periodo de prueba, si desea seguir escuchando este servicio, deberá contrata rlo. para suscribirse vaya a www.siriusxm.com /internetradio con s[...]

Uso de In ternet Radio Es-5 Last.fm es un servicio musica l que sabe lo que le gusta... Su nuevo receptor de AV O nkyo es muy inte ligente. Si tiene una cuenta gratuita de Last.fm, hará un seguimiento de todas las canciones que acaba de escuchar. Cuando visite el sitio web de Last.fm, podrá ver listas personales de la música que ha disfrutado, c[...]

Uso de In ternet Radio Es-6 Uso de Slacker Personal Radio 1 Si no tiene una cuenta, cree una en el sitio web de Slacker (www.slacker.co m) con su ordenador. Si ya tiene una cuenta d e Slacker, seleccione “Sign in to your account” y pulse ENTER . Aparecerá la pantal la de teclado. Puede introducir información desde el man do a distancia o desd[...]

SN 29401189B (C) Copyright 2012 Onkyo Sound & Vision Cor poration Japan. All rights reser ved. Y1203-2 * 2 9 4 0 1 1 8 9 B *[...]

En-1 Using Internet Radio Using Internet Radio Note • Available services may vary depending on the r egion. Common Procedures in Internet Radio Menu 1 Press NET . A list of the network serv ices appears, and the NET indicator lights. If it flashe s, verify that the Ethernet cable is firmly connected to the AV receiver. 2 Select the des ired servi[...]

Using Internet Radio En-2 Last.fm is a music s ervice th at learns what you love... Your new Onkyo AV receiver is very clever. If you have a free Last.fm account, it will keep track of all the songs you’ve just played. When you visit the Last.fm website, you can see personal charts of the music you’ve enjoyed, share them with friends and see wh[...]

Internetradio verwenden De-1 Internetradio verwenden Anmerkung • Die verfügbaren Dienste sind länderab hängig verschieden. Allgemeine Verfahren bei den Internetradio-Me nüs 1 Drücken Sie NET . Es erscheint eine Liste der Netzwerkdienste und die NET -Anzeige leucht et. Wenn sie bli nkt, überprüfen Sie ob das Ethernet-Kabel fest im AV-Receiv[...]

Internetradio verwenden Last.fm ist ein Musikdiens t, der sich Ihre Lieblingsmusik merkt... Ihr neuer Onkyo AV-Receiver ist äußer st clever. Wenn Sie ein kostenloses Last.fm-Konto ei ngerichtet haben, werden darin all e kürzlich abgespiel ten Titel gesp eichert. Wenn Sie die Last.fm- Website besuchen, können Sie Ihre persönl ichen Charts der v[...]

Remote Co ntrol Codes 1 Remote Control Codes / 1 While holding d own the REMOTE MO DE bu tton to which you want to assign a code, press and hold down [DISPLAY] (about 3 seconds). The REMOTE MODE button/ Remote indicator lights. On Integra products, button names are ca pitalized. For example , “Remote Mode” button and “Display” button. Notes[...]

Remote Co ntrol Codes 2 Codes de télécommande Códigos de control remoto 1 Tout en maintenant enfoncé le bouton REMOTE MODE auquel vous souhaitez associer un code, pressez et maintenez enfoncé le bou ton [DISPLAY] (pendant environ 3 secondes). Le bouton REMOTE MODE/le témoin Remote s’allume. Les noms de boutons sont en manjuscules su r les p[...]

Remote Co ntrol Codes 3 Codici del telecomando Fernbedienungscodes 1 Tenendo premuto il tasto REMOTE MODE al quale si desid e ra assegnare il codice, premer e e tenere premut o [DISPLAY] (per circa 3 secon di). Il tasto REMOTE MODE/l'indi catore Remote si acce nde. Sui prodotti Integra, i nomi dei tasti sono scri tti con l'iniziale maiu s[...]

Remote Co ntrol Codes 4 Afstandsbedieningscod es Fjärrstyrningskoder 1 Houd terwijl u de REMOTE MODE toets ingedrukt houdt waarvoor u een code wilt toewijzen de [DISPLAY] toet s ingedrukt (ongeveer 3 seconden). De toets REMOTE MODE (afstandsbed ieningsmodus) / Het indicatielampje afstandsbediening gaat branden. Op producten van Integra staan de na[...]

Remote Co ntrol Codes 5 遙控代碼 遥控代码 1 在按住想指定編碼的 REMOTE MODE （遙控模式）按鈕時，同時按住 [DISPLAY] （顯示） （約 3 秒） 。 REMOTE MODE （遙控模式）按鈕 / 遙控指示燈亮起。 在 Integra 系列產品上， 按鈕名稱為大寫。 例如， 「Remote Mode」 （遙控模式） 按?[...]

Remote Co ntrol Codes 6 Dedicated On kyo Receiver Default 62503 Zone 2 62506 Zone 3 62507 Cable Set T o p Bo x ADB 02254, 0 2769 Aon 02769 Arris 02187 AT&T 00858 Bright House 01376, 01877 BT Vision 02294 Cable & Wireless 01068 Cable One 01376, 01877 Cablecom 015 82 Cablevision 01376, 0187 7 Charter 01376, 01877, 02187 Cisco 01877, 0085 8, 0[...]

Remote Co ntrol Codes 7 AT&T 00858 BT Vision 02294 Cisco 00858, 0234 5, 02378 Kreatel 01385 Motorola 00858, 02378 Neuf TV 03107 Philips 02294 Scientific Atlanta 00858 SFR 03107 Verizon 0237 8 CD Advantage 70032 AH! 70157 Aiwa 70157 Arcam 70157 Atoll Electronique 70157 Audio Research 7015 7 Audiolab 70157 Audiomeca 70157 Audioton 70157 AVI 70157[...]

Remote Co ntrol Codes 8 Polk Audio 82228 Video - Accessory ADB 02254, 0 2769 Aon 02769 Apple 02615 AT&T 00858 BT Vision 02294 Canal+ 02657 Cisco 00858, 0234 5, 02378 Kreatel 01385 mio TV 02802 Motorola 01376, 00858, 019 98, 02378 Neuf TV 03107 Pace 02657 Philips 02294 Scientific Atlanta 00858, 02345 SFR 03107 SingTel 01998, 02802 TeliaSonera 01[...]

Remote Co ntrol Codes 9 Hama 01567 Hanseatic 01100 Hirschmann 00173 Hitachi 01284 Hornet 01300 HTS 00775 Humax 01377, 0 1176, 01427, 01675, 0180 8, 01882, 01915, 0214 4, 02408, 02616 ID Digital 01176 ID Sat 01334 ILLUSION sat 0163 1 Imperial 0 1195, 01334 Indovisio n 00887 iNETBOX 01237 Inno Hit 01626 Innova 00099 inVion 02418 iotronic 01413 ISkyB [...]

Remote Co ntrol Codes 10 Star 00887 Stream System 01300 Strong 00853, 0 0879, 01284, 01300, 0140 9, 01626, 02418 Sunny 01300 Sunstar 00642 Supernova 00887 Supratech 01413 Systec 01334 Sytech 02418 TBoston 0125 1, 02418 Teac 01251 Technical 01626 Technika 01284 TechniSat 0 1100, 01195 Technosat 01206 Techwood 01251, 0 1284, 016 26 TELE System 0 1251[...]

Remote Co ntrol Codes 11 Akai 10178, 10556, 10037, 10714, 1071 5, 10208, 11675 Akiba 10037 Akito 10037 Akura 1 0171, 1003 7, 10714, 10668, 1103 7, 11363, 11585, 1166 7, 11709 Alba 10037, 10714, 10668, 11037, 1158 5 Alien 11037 Allstar 10037 Amstrad 10171, 10037, 110 37 Anam 10037 Anam National 10037, 1065 0 Andersson 11585 Anitech 10037 Ansonic 100[...]

Remote Co ntrol Codes 12 Erres 10037 ESA 10171 ESC 10037 Euroman 1003 7 Europa 10037 Europhon 1003 7 Evesham 11248, 1 1667 Excello 11037 Exquisit 10037 Ferguson 10037, 10625, 105 60, 10195, 1103 7, 11585 Fidelity 10171, 1003 7, 10512 Finlandia 1020 8 Finlux 10556, 1 0037, 10714, 10715, 1124 8, 11667 Firstline 10556, 10037, 10714, 10668, 1103 7, 102[...]

Remote Co ntrol Codes 13 Lifetec 1003 7, 10714, 10668, 11037, 1200 1 Linsar 1158 5 Local India TV 10208 Local Malaysia TV 10698 Lodos 11037 Loewe 10037, 10512, 118 84 Logik 11037, 1069 8 Logix 1066 8 Luma 11037 Lumatron 10037, 10668 Lumenio 10037 Lux May 10037 Luxor 11037, 10208 LXI 10178 M Electronic 10037, 10714, 106 34, 10195, 1051 2, 11652 Madi[...]

Remote Co ntrol Codes 14 Phoenix 10037 Phonola 10556, 10037 Pioneer 10037, 10698, 10512, 11457, 1163 6, 12171 Plantron 10037 Playsonic 10037, 1071 4, 10715, 11652 Powerpoint 1003 7, 10698 Prinston 11037, 10715 Profitronic 10037 Proline 10037, 10625, 10634, 11037 Prosonic 10037, 10714, 10668, 11324, 1158 5, 11667, 11709, 1200 1 Protech 10037, 10668,[...]

Remote Co ntrol Codes 15 Technosonic 10556, 1062 5, 10499, 11324 Techvision 11709 Techwood 11037, 1 1667 Tecnimagen 10556 Teco 10178, 10653 Tedelex 10208, 1170 9 Teknika 10150 TELE System 11585 Telecor 1003 7 Telefunken 10037, 1 0625, 10714, 10560, 1069 8, 11585, 11667 Telefusion 10037 Telegazi 10037 Telemeister 10037 Telesonic 10037 Telestar 10556[...]

Remote Co ntrol Codes 16 Technics 10556 Thomson 10625 DVD 3D LAB 30539 Accurian 30675 Acoustic Solutions 30713 AEG 30675 AFK 31152 Aiwa 30533 Akai 30675 Alba 30539, 30713 Ambiance 33052 Amstrad 30713 Anthem 32820 Aristona 30539, 30646 ASDA 32213 Audix 30713 Autovox 30713 Awa 32587 Basic Li ne 30713 Bel Canto Design 31571 Black Diamond 30713 Blue Pa[...]

Remote Co ntrol Codes 17 Radionette 30741 Radiotone 3071 3 RCA 30522, 3057 1, 32213, 32587 REC 30490 Red 32213 Redstar 31394 Roadstar 30713 Rotel 30623 Salora 30741 Samsung 30490, 3 0573, 30199, 30820, 3163 5, 32069, 32329, 3248 9, 33195 Sanyo 30713 Schneider 30539, 30646, 30713 Schoentech 30713 Scott 31394 SEG 30713 Semp 30503 Sharp 30630, 3067 5,[...]

Remote Co ntrol Codes 18 Victor 31597 Yamaha 30646 Zenith 30741 HD-DVD Integra 3290 1, 33104 33 504 LG 30741 Microsoft 3208 3 Onkyo 3290 1, 33104 33 504 Xbox 32083 TV/DVD Combination Akai 11675 Black Diamond 11037, 3 0713 Blue Sky 11037, 3071 3 Bush 11037, 1069 8, 12719, 30713 Centrum 11037, 3071 3 Crown 1 1037, 30713 DMTech 12001 Dual 11037, 30713[...]

Remote Co ntrol Codes 19 Memo[...]

SN 29401094 (C) Copyright 2012 ONKY O SOUND & VISION CORPORA TION Japan. All rights reserved. * 2 9 4 0 1 0 9 4 * Y1112-1[...]