Deutsch dropdown-ico

Pelco ES3012 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Pelco ES3012 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Pelco ES3012, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Pelco ES3012 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Pelco ES3012. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Pelco ES3012 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Pelco ES3012
- Den Namen des Produzenten und das Produktionsjahr des Geräts Pelco ES3012
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Pelco ES3012
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Pelco ES3012 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Pelco ES3012 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Pelco finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Pelco ES3012 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Pelco ES3012, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Pelco ES3012 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    ES3012 Series Esprit ® C306M-K (4/05) ® INST ALLA TION MANUAL[...]

  • Seite 2

    2 P elco Manual C306M-K (4/05)[...]

  • Seite 3

    P elco Manual C306M-K (4/05) 3 CONTENTS Section Page IMPORT ANT SAFETY INSTR UCTIONS ............................................................................ 5 DESCRIPTION ................................................................................................................... 6 MODELS .................................................[...]

  • Seite 4

    4 P elco Manual C306M-K (4/05) LIST OF ILLUSTRA TIONS Figur e Page 1 Esprit ES3012 System Dimensions Drawing .................................................... 37 LIST OF TABLES T able Page A Switch Settings for SW1 ................................................................................... 32 B Switch Settings for SW2 ...................[...]

  • Seite 5

    P elco Manual C306M-K (4/05) 5 IMPOR T ANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not bloc k any ventilation openings . Install in accordance with the manufacturer’ s instructions. 6. Do not install near any heat sources such as radiators, heat registers,[...]

  • Seite 6

    6 P elco Manual C306M-K (4/05) DESCRIPTION The Esprit ® ES3012 Series Integrated Positioning System is available as a basic system or as an ImageP ak ® camera and lens package . The basic system integ rates a pan and tilt, camera enclosure, and receiv er (camera and lens not included). The ES3012 ImageP ak in- cludes the basic system, plus a came[...]

  • Seite 7

    P elco Manual C306M-K (4/05) 7 INST ALLA TION The basic ES3012 system does not include a camera and lens package . Therefore you m ust install a camera and lens in the enclosure bef ore mounting the pan/tilt to the base of the system. CAMERA AND LENS INST ALLA TION (Skip this section if you are installing an ES3012 ImageP ak camera and lens package[...]

  • Seite 8

    8 P elco Manual C306M-K (4/05) A B 3 Attach the camera and lens to the mount. Extend the lens to the maximum length before positioning the camer a and lens. A. P osition the camera and lens so the lens does not extend be yond the end of the mount. B. Fasten the camera and lens to the mount with the 1/4-20 Phillips screws , lock washers, and flat w [...]

  • Seite 9

    P elco Manual C306M-K (4/05) 9 P AN AND TIL T INST ALLA TION 1 When installing the ES3012 Esprit system, allow f or sufficient clear- ance between the top of the unit and ov erhead obstr uctions. This will prev ent interference when the en- closure is driven to its maximum el- ev ation of 40 degrees. 2 Remov e the transformer module from the base o[...]

  • Seite 10

    10 P elco Manual C306M-K (4/05) 4 Route the wires and cables through the center of the Esprit mount. Re- install the transf or mer module into the base. The transf ormer module can be positioned in the mount base in only one orientation. 5 ES3012-5 Model Only – Set the 120/230 voltage selector s witch on the trans- for mer to the appropriate volt[...]

  • Seite 11

    P elco Manual C306M-K (4/05) 11 8 Tu rn on the po wer . If the red LED lights, turn off the power and proceed to the ne xt step . If the red LED does not light, refer to the T roubleshooting section. 9 Plug the male Esprit system connector , located on the bottom of the pan and tilt, into the female Esprit system connector located on the transf orm[...]

  • Seite 12

    12 P elco Manual C306M-K (4/05) TXB SERIES TRANSLA TOR BOARD INST ALLA TION (OPTIONAL) P elco’ s TXB Ser ies allows controllers from other companies to communicate with the Esprit system. To install a TXB Ser ies board, remov e the left cover of the pan and tilt. Once the cover is removed, refer to the manual supplied with the translator board to[...]

  • Seite 13

    P elco Manual C306M-K (4/05) 13 To reinstall the pan and tilt co ver , do the f ollowing: 1. Properly position the cover and slide it into place . The sides of the cover must fit under the front and back rain guards of the pan and tilt, and the top of the cover must seat against the lip of the top gasket. 2. Apply pressure and push the top of the c[...]

  • Seite 14

    14 P elco Manual C306M-K (4/05) OPERA TION POWER-UP DISPLA Y When the Esprit system is powered up or reset, the selected protocol, re vision number , and other information is displa yed on the monitor . For e xample, the screen might show the f ol- lowing inf or mation: The information displa yed depends on the selected protocol (C, D , or P) and t[...]

  • Seite 15

    P elco Manual C306M-K (4/05) 15 P AN, SCAN, AND TIL T SPEEDS Pan and scan speeds are adjustable from 3 to 40 degrees per second through the pro- gr amming menu. The tilt speed is one-half of the pan speed. LENS FUNCTIONS Lens zoom, f ocus, and iris functions are operated from the controller . All lens models hav e motorized zoom and f ocus, and dir[...]

  • Seite 16

    16 P elco Manual C306M-K (4/05) PROGRAMMING ESPRIT MENUS To access the main menu, program preset 95. To mak e selections in the main menu, use the follo wing controls: Joystick: Move up or down to position cursor or to toggle between selections. Iris Open: Enter. Iris Close: Cancel. For detailed programming instructions, refer to the sections on th[...]

  • Seite 17

    P elco Manual C306M-K (4/05) 17 ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor b y programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 f or P elco’ s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below [...]

  • Seite 18

    18 P elco Manual C306M-K (4/05) AZ/EL Other Menu P ark Time 0 Pan/Scan Spd 7 Power Up Default Pat length 6 min Spd Profile 50 MPH wind < Zone Blank> <Az /El / Direction> Exit Az/El/Direction Set Azimuth Zero Az/El Az/El Line Direction Direction Line Disp Duration Exit Az/El programs the horizontal displa y position of the Azimuth 1 /Ele[...]

  • Seite 19

    P elco Manual C306M-K (4/05) 19 AZ/EL LINE Az/El Line controls the vertical display position of the Azimuth/Ele vation label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting. To program the v er tical label positi[...]

  • Seite 20

    20 P elco Manual C306M-K (4/05) AZIMUTH ZERO Azimuth is the pan angle from 0 ° to 359 ° . Azimuth zero is the prog rammed 0 ° point that is normally set to magnetic north. Once programmed, on-screen pan position (azimuth) and compass readings are based on the set azimuth zero point. To set azim uth zero: 1. Program preset 95 (28). The main menu [...]

  • Seite 21

    P elco Manual C306M-K (4/05) 21 DIRECTION Direction programs the horizontal displa y position of the Direction label (N, NW , NE, …). The following settings are available for the Direction label: Off – Label is not display ed. Left – Label is displayed on the left-hand side of the screen. Center – Label is displayed in the center of the scr[...]

  • Seite 22

    22 P elco Manual C306M-K (4/05) DIRECTION LINE NOTE: Direction display is not available while you are programming or running a pattern. Other Menu P ark Time 0 Pan/Scan Spd 7 Power Up Default Pat length 6 min Spd Profile 50 MPH wind < Zone Blank> <Az /El / Direction> Exit Az/El/Direction Set Azimuth Zero Az/El Az/El Line Direction Direc[...]

  • Seite 23

    P elco Manual C306M-K (4/05) 23 DISPLA Y DURA TION Display Dur ation programs the duration the Az/El, Direction, and Zoom labels are displa yed on the monitor . The av ailable settings for displa y duration include the f ollowing: CONST ANT - The label is displa yed continuously . 2 SECONDS (default) - The label is displayed f or 2 seconds after PT[...]

  • Seite 24

    24 P elco Manual C306M-K (4/05) LIMIT STOPS TURNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1. Program preset 95 (28). The main menu appears . 2. Position the cursor (>) beside Limits. 3. Press the Iris Open button to enter the Limits menu. 4. Position the cursor (>) beside Limit Stops. 5. Press the Iris Open button. The cursor m[...]

  • Seite 25

    P elco Manual C306M-K (4/05) 25 Scan Limit Stops When scan limit stops are set, the pan and tilt reverses direction during random, frame, or auto scanning when a limit stop is reached. The manual scan limit stops can be set in one of two ways: At the controller by programming presets 92 (25) and 93 (26) or At the controller by programming the Limit[...]

  • Seite 26

    26 P elco Manual C306M-K (4/05) P AN/SCAN SPEED The pan/scan speed is adjustable from 3-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan. To change the pan/scan speed: 1. Program preset 95 (28). The main menu appears . 2. P osition the cursor (>) beside Other . 3. Press the Iris Open button to enter the Other [...]

  • Seite 27

    P elco Manual C306M-K (4/05) 27 POWER-UP MODE This feature lets the system resume a desired condition f ollowing power-up . The menu in- cludes the following choices. • Default - On power-up, the pan and tilt goes through a configuration cycle and stops at zero reference, showing “Configuration Done,” address, and mode settings on the screen.[...]

  • Seite 28

    28 P elco Manual C306M-K (4/05) SPEED PROFILE This feature allows the operator to set the wind speed conditions for the location of the system. Y ou can set two wind speed profiles of 50 mph or 90 mph in which the system will remain operational. In both settings, the pan speed will be a maximum of 40 degrees per second. The difference will be in th[...]

  • Seite 29

    P elco Manual C306M-K (4/05) 29 ZONES Basic rules for setting zones: 1. Refer to the documentation for your control system to program zones. 2. Establish zones using the controller , pr ior to programming ZONE BLANK with the Es- prit onscreen menu. 3. T o accurately set z one areas, zoom wide to the maximum field of vie w . 4. Set zones moving the [...]

  • Seite 30

    30 P elco Manual C306M-K (4/05) TROUBLESHOOTING Symptom: System does not operate. 1. Check system input v oltage. 2. Check f or proper positioning of input power select s witch for the transf ormer (ES3012-5 models only). 3. The Esprit system is protected by a resettable o vercurrent protective de vice located in the transf or mer module. Whenev er[...]

  • Seite 31

    P elco Manual C306M-K (4/05) 31 Symptom: No video or poor video 1. Check the video and power connections to the camera. 2. Check for power to the camera from the Esprit system camera power output. 3. Check all coax BNC connectors from the camer a to the monitor. 4. Make sure the controller is set for the correct camera-to-monitor viewing combinatio[...]

  • Seite 32

    32 P elco Manual C306M-K (4/05) APPENDIX NOTE: Esprit will sense and automatically select input from Coaxitron control signals in either the standard or e xtended mode. Therefore , the DIP switches settings ha ve no effect on Coaxitron control signals . Ta b le A. Switch Settings f or SW1 Baud Rate Switch Setting SW1-1 SW1-2 SW1-3 2400 OFF OFF OFF*[...]

  • Seite 33

    P elco Manual C306M-K (4/05) 33 Ta b le B. Switch Settings f or SW2 NOTE: The Esprit will sense and automatically select input from Coaxitron control signals in either the standard or e xtended mode. Theref ore, the DIP s witches settings have no eff ect on Coaxitron control signals. Receiver Address Switch Setting P-T ype D-T ype Control Control S[...]

  • Seite 34

    34 P elco Manual C306M-K (4/05) Ta b le B. Switch Settings f or SW2 (continued) (Continued on ne xt page) Receiver Address Switch Setting P-T ype D-T ype Control Control SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 – 112 OFF OFF OFF OFF ON ON ON OFF – 113 ON OFF OFF OFF ON ON ON OFF – 114 OFF ON OFF OFF ON ON ON OFF – 115 ON ON OFF OFF O[...]

  • Seite 35

    P elco Manual C306M-K (4/05) 35 Ta b le B. Switch Settings f or SW2 (continued) Receiver Address Switch Setting P-T ype D-T ype Control Control SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 – 232 OFF OFF OFF ON OFF ON ON ON – 233 ON OFF OFF ON OFF ON ON ON – 234 OFF ON OFF ON OFF ON ON ON – 235 ON ON OFF ON OFF ON ON ON – 236 OFF OFF ON[...]

  • Seite 36

    36 P elco Manual C306M-K (4/05) SPECIFICA TIONS ELECTRICAL Input V oltage: 24 or 120/230 V A C, 50/60 Hz; on ES3012-5 models, a s witch is installed on the transf or mer module located in the mount base to make 120 or 230 V AC input v oltage selection. Reset feature enabled when pow er becomes unstable or interrupted. Po w er Requirements: Maximum [...]

  • Seite 37

    P elco Manual C306M-K (4/05) 37 Figure 1. Esprit ES3012 System Dimensions Drawing 13.8 (35.1) 4.1 (10.5) 14.0 (35.5) 4.8 (12.3) 9.1 (23.2) 7.7 (19.7) 6.9 (17.5) 7.9 (20.2) 16.4 (41.7) 5.2 (13.3) NOTE: V ALUES IN P ARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. 17.3 (43.9)[...]

  • Seite 38

    38 P elco Manual C306M-K (4/05) REGULA TOR Y NOTICES This equipment has been tested and found to comply with the limits of a Class B digital de vice, pursuant to par t 15 of the FCC rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation. This equipment generates, uses, and can [...]

  • Seite 39

    P elco Manual C306M-K (4/05) 39 P elco, the P elco logo, Camclosure , Espr it, Genex, Legacy , and Spectra are registered trademarks of P elco. ©Copyright 2005, P elco. Endura and ExSite are trademarks of P elco. All rights reser ved. Lexan is a registered trademark of the General Electric Company . REVISION HISTOR Y Manual # Date Comments C306M 1[...]

  • Seite 40

    W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East[...]