Planet Technology ICA-350 Bedienungsanleitung

30M Infrared Internet Camera ICA-350 User ’ s Manual V ersion: 2.00 Date: May . 15 1/59[...]

Copyright Copyright © 2008 by PLANET T echnology Corp. All right s reserved. No p art of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer lang uage, in any form or by any means, ele ctronic, mechanical, magnet ic, optical, chemical, manual or otherwise, without [...]

Safety This equipment is de signed with the utmost ca re for the safety of those who in st all and use it. However , special attention must be paid to t he dangers of electric shoc k and static electricity when working with ele ctrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure[...]

T able of Content 1. Introduction ............................................................................................................................. 5 1.1 Overview ......................................................................................................................... 5 1.2 Features ......................................[...]

3.1 1 E-Mail ............................................................................................................................ 59 3.12 Object Detection ........................................................................................................... 60 3.13 Event Server ..........................................................[...]

1. Introduction The ICA-350 features zero -lux illumination. The 28 IR illuminator built around the lens brings the clearest vision at night. The ICA-350 offers color vision in day time and mon ochrome vision at complete darkness environment with built 1/3” co lo r Sony CCD sensor up to 30 meters of di stance and use new High-Lig ht LED to provid[...]

• Motion Detection: the motion detection featur e can monitor any suspiciou s movement in specific area • Supports 2- W ay Audio function with hardware version 2 1.3 Package Content s User can find the following item s in the package for ICA-350: ICA-350 x 1 Power adapter x 2 Wall mount accessories x 1 Installation software and m anual CD x 1 Q[...]

2. Basic Setup This chapter provides det ails of installi ng and configuring the ICA-350 2.1 System Requirement s Network Interface 10/100MBase-TX Ethernet Monitoring System Recommended for Intern e t Explorer 6.0 or later Basic System Hardwa re · CPU: Pentium 4, 3.0GHz or above · Memory Size : 512 MB (512 MB or above Recommended ) · VGA card re[...]

2.2 Physical Det ails Identification of ICA-350 cables Video Output Connector (B NC port) The ICA-350 also provides composite video output. User can u se BNC video cable to connect the ICA-350 with a TV monitor or DVR. Power Connector (fo r ICA-3 50) The input power is 12VDC. It supply two adapte rs that one for heater and the other for camera. NOT[...]

2.3 Hardware Inst allation 1. Fix ICA-350 to the location with wall mount fixture. 2. Plug-in Ethernet Cable into RJ-4 5 LAN port. Connect an Ethernet cable to the LAN port on the ICA-350 and connect the other side of the Ethernet ca ble to a hub/switch. 3. Connect the attached two power adapters to cam era and plug-in this two adapters into powe r[...]

3. The “Welcom e to the InstallShield Wiza rd for IP Wizard” will display on the screen and click “Next” to continue. 4. Please click “Next” to install with original settings, or you may click “Change…” button to modify the install folder then pres s “Ne xt” to continue. 10[...]

5. Please click “Install” to st art the installation. 6. Please click “Finish” to complete the installation 7. Please double-click the utility icon on the desktop then y ou will see the ICA-350 utility . 11[...]

2.5 IP Wizard When you installed the IC A-350 on a LAN environm ent, you may execute IP Wizard to discover ICA-350’s IP address and set up related parameters in the ICA-35 0. Search Button: When click Search button, a searching window will po p up. IP Wizard is starting to search ICA-350 on the LAN. The message “No Network Devices Is Found” w[...]

Wizard Button: When IP Wizard finds y our cam era, Wizard button will become available. Please select the device you would like to configure in the Information Box. The device will turn into yellow which means this device is selected; please press “ Wizard ” button. Or you could double click the mouse left key on the selected camera. Relative s[...]

2.6 Configure With IP Wizard After pressing Inst allation Wizard, please key in Username and Passwo rd of the device when login dialog box appears on the screen. Y ou can login the setup page if authorized name and password is correct. Default username/p assword for machine login: admin /<no password> Wizard Page 1: Username and Pass word Thi[...]

Wizard Page 2: LAN Setting This page is about the select of Static IP or DHCP ON. LAN You can configure this ICA-350 to obtain its address automatically or manually assign. If there is a DHCP server in your network environment and you select “ DHCP ON ”, ICA-350 can automatically obt ain an IP address. If you don’t have DHCP server or you wan[...]

address 192.168.0.20 . User may now open your web bro wser , and key in http://192.168.0.20 in the address bar of your web browser to logon ICA -35 0’ s web configuration p age. Wizard Page 3: Confirmation This page sh ows the n ew configurations. If it is correct, please pre ss “Submit” icon and the setting information will be save to your I[...]

2.7 UPnP Function NOTE: Windows 2000 doe s not su pport UPnP feature. 2.7.1 Windows XP  UPnP™ is short for Universal Plug and Play, whic h is a networking a rchitecture that provides compatibility among network ing equipment, software, and perip herals. This device is an UPnP enabled device. If the operating sy stem, Windows XP, of your PC i s[...]

The “Add or Remove Programs” will display on the screen and click Add/Remove Wido ws Components to continue. The following screen will a ppea r, select Networking Services and click Details to continue 18[...]

The “Networking Services” will display on the screen, sele ct Universal Plug and Play and click OK to continue. Please click Next to continue 19[...]

The program will start installing the UP nP autom atically. You will see t he below pop-up screen, please wait while Setup configures the components. Please click Finish to complete the UPnP installation 20[...]

Double-click My Network Places on the desktop, the “My Network Places” will display on the screen and double-clic k the UPnP ico n with ICA-350 to view your device in an internet browser. 2.7.2 Windows Vist a  UPnP™ is short for Universal Plug and Play, whic h is a networking a rchitecture that provides compatibility among network ing equi[...]

Double-click My Network Places on the desktop, the “My Network Places” will display on the screen and double-clic k the UPnP ico n with ICA-350 to view your device in an internet browser. 22[...]

2.8 Setup ActiveX to use the ICA-350 The ICA-350 web pag es communicate with the ICA -350 using an ActiveX control. The ActiveX control must be download ed from the ICA-350 and installed on y our PC. Your Internet Explorer security settings must allo w for the web page to work correctly. To use the ICA-350, u ser must setup his IE browser as follow[...]

2.8.2 Internet Explorer 7 for Windows XP  From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î ”Custom Level…”, p lease setup your “Settings” as follow. Set the first 3 items • Allow previously unused ActiveX control to run… • Allows Script lets • Automatic prompting for ActiveX controls By now, [...]

25 2.8.3 Internet Explorer 7 for Windows V ist a  From your IE browse Î ”Tools” Î ”Internet Option s…” Î ”Security” Î ”Internet ” Î ”Custom Level…”, please setup your “Settings” as follo w. • Enable “Automatic prompting for ActiveX control s” • Prompt “Initialize and script active cont rols not marked?[...]

3. Web-based Management This chapter provides setup det ails of the ICA-350’ s Web-base d Interface. 3.1 Introduction The ICA-350 can be configured with your Web Bro wser . Before configure, ple ase make sure your PC is under the same IP segment with ICA-350. 3.2 Connecting to ICA-350 z Use the following procedure to est ablish a connection from [...]

Web browse r may display the “Security W arming” window , select “Y es” to in stall and run the ActiveX control into your PC. After the ActiveX control was installed and run, the first image will be displayed. NOTE: If you log in the ICA-350 as an ordi nary user , setting function will be not available. If you log in the ICA-350 as the admi[...]

3.3 Live V iew S t art-up screen will be as follow no matter an ordinary us ers or an administrator . S t reaming Protocol V ideo Profile A ctiveX Control Language Setting Menu PTZ Control 2-W a y Audio De-Interlace Monitor Image Section V ideo Information Monitor Image Section The image shot by the ICA-350 is shown here. Th e date and time are dis[...]

below . : Disable de-interlace function. : Enable de-interlace function. Setting Menu This function is det ail setting for ICA-350 that only available for user logged into ICA-350 as administrator . Item Action Network Configure Network settings such as DHCP, DDNS, 3GPP, PPPoE and UPnP Camera Adjust camera parameters System Configure system informa[...]

PTZ Control Click to display the following co ntrol p anel: Hide PTZ Control Camera Direction Camera S p eed Preset To u r Go T ou r A uto Pan Hide PTZ Control Click the icon will hide the PTZ control function. Camera Direction Control camera up/down/le ft/right and home position. Camera Speed Choose the speed of Pan and Tilt. Preset Add/Update the[...]

3.4 ActiveX Control The plug-in ActiveX control support s a lot of functions by clicking the lef t mouse button. Note that this feature only support s on the ActiveX c ontrol within Microsof t® Internet Explorer . On the ActiveX control icon, click the Lef tMous eButton, then a menu pop-up. T his menu provides features that are unique to the Activ[...]

3.4.1 Digit al Zoom Click Digit al Zoom to active this function as above. User can drag or scale the box over the video to adjust zoom ratio and position. 3.4.2 Record Click Record to activate this function. Press Record button to start recording. The video file is saved as ASF format into your local PC. While you want to stop it, press Sto p to st[...]

3.4.3 Snap shot Click Snapsh ot to activate this function. Press Snapshot button to t ake a picture. The image file is saved as JPEG format into your local PC. Select Bro w ser , the pop-up window to select the save path and file name prefix, select OK to contin ue. If you like to retrieve the saved image, select the file t o display the saved imag[...]

3.4.5 St atistics Click St atistics to activate this function. A window will be popup to show the st atistics information of the streaming st atus. Note that this information is the st atistics between the device and your local PC. 3.4.6 About Click About to show the ActiveX information 34[...]

3.5 Network Use this menu to configure the network to connect the device and the clie nt s. 3.5.1 Network This section provides the menu of co nn ecting the device through Ethernet cable. MAC Address Display the Ethernet MA C address of t he device. Note that user cann ot change it. Obt ain an IP address automatically (DHCP) DHCP: S t ands for Dyna[...]

1 1 1 1 1 1 1 1 00000000 will usually be shown in the correspondi ng, more readable form as 255.255.255.0. Gateway A gateway is a piece of software or hard ware that passes information between networks. Y ou'll see this term mo st often when you either log in to an Internet site or when you're transi ent email between dif ferent servers. [...]

IP address problem comes in the form of a dynamic DNS service. The Internet uses DNS servers to lookup domai n names and tra nslates them into IP addresses. Domain names are just easy to reme mber aliase s for IP addresses. A dynamic DNS service is unique because it provides a means of updating your IP address so that your listing will remain curre[...]

• Connect to a LAN by DHCP or Fixed I P • Acce ss the device, enter Setting Î Network Î PPPoE as below PPPoE To enable or disable the PPPoE service here. User Name Type the user name for the PPPoE service which is provided by ISP. Password Type the password for the PPPoE serv ice which is provided by ISP. IP Address, Subnet Mask, and Gateway [...]

RTSP Port Choose the RTSP port. The RTSP protocol allows a connecting client to start a video stream. Enter the RTSP port number to use. The default value is 554. RTP Port Specify the range of transmission p ort nu mber of video stream. The default range is 50000 to 50999. User can specify a numbe r between 1024 and 65535. To use the 3GPP function,[...]

traversal when your device is located on an intranet (LAN) and you wish to make it available from the other (WAN) side of a NAT router. With NAT traver sal properly configured, all HTTP traffic to an external HTTP port in the NAT router will be forward e d to the device. UPnP To enable or disable the UPnP service here. Friendly Name Shows the frien[...]

IP Filter To enable or disable the IP filter function here. IP Filter Policy Choose the filter policy where is denying or allowing. 3.5.7 IP Notification In case the IP address i s changed, system is abl e to send out a n email to alert someone if the function is enabled. 41[...]

SMTP Notification (e-mail) If enable this function, then the “ Send to “ and “ Subject ” field need to be filled. Send To Type the receiver ’ s e-m ail address. This address is u sed for reply mail. Subject Type the subject/title of the E-mail. TCP Notification If enable thi s function, then the “ TCP Server “ , “ TCP Port ” , and[...]

Proxy Port Set port number of Proxy. Proxy Login Name Type the user name for the HTTP Proxy. Proxy Login Password Type the password for the HTTP Proxy. Custom Parameter User can set specific parameters to HTTP server. Message The message will be sent to HTTP server. 43[...]

3.6 Camera Use this menu to set the function of the camera of ICA-350 3.6.1 Picture Brightness Large value will brighten camera. Sharpness Large value will sharpen camera. Contrast Large value will contrast camera heavil y. Local Video Output Check this item if a TV or video monitor ha s been connected to video output of the Network Camera. Un-c he[...]

3.6.2 PTZ Setting PTZ Protocol Type The Network Camera is connected to built-in ICA -350 and controls this device thru RS485 bus. Baud Rate This is the communication speed between network module and ICA-350. Note that please DO NOT change s the default value except on special purpose. If so, user needs to check and set value properly for both sides[...]

3.6.3 Preset Setting This page pro v ides the edit tool to modify or delete the “Preset Setting” item by item. 3.6.4 T our Setting Up to 64 positions can be preset, and th e came ra can be programming to move to the preset position sequentially . Tour Name The group name of the sequence of came ra tour. The maximum number of camera tour is 16. [...]

Running Enable o r disable this cam era tour. Preset Set the sequence of the tour. Maximum 16 points can be assigned. The sele cted preset position is added in the Sequen ce list from 1 to 16. Wait Time Type a period of time during which th e came ra is to stay at each preset poi nt, between 0 to 36000 secon ds. To use the camera tour function, use[...]

3.7 System Use this menu to perform the princip al settings of ICA -350. 3.7.1 System Device Title You can enter the name of this unit h ere. It’s very useful to identify the specific device fr om multiple units. Software Version This information shows the softwa re version in the d evice. Log User can check the syst em log information of the dev[...]

3.7.2 Date & Time Y ou can setu p the time setting of ICA-350, make it synchronized with PC or remote NTP server . Also, you may select the correct time zone of your country . Server Date & Time Displays the date and time of the device PC Time Displays the date and time of the connected PC Manual setting: Click this option to set time and d[...]

Daylight Saving Stop Time Sets up the date and time of daylight saving stop time. Daylight Saving Offset Sets up the date of daylight saving offset. 3.7.3 Maintenance Hard Factory Default (Include the network setting) Recall the device hard factory default settings. Note that click this button will reset all device’s pa rameters to the factory se[...]

3. Disable Motion Detection function. 4. Select “ Firmw are name ” 5. Select the Firmware binary file. ( Note that it must make sure that the Firmware only applies to this device, once update, it will be burned into FLASH ROM of system. ) 6. Once the firmware file was selected, select “Upgrade”. 7. The upgrade progress i nformation will be [...]

3.8 V ideo This device provides more video profil es as below to support dif ferent request to each client simultaneo usl y . Each user can choose his pref erred video profile as his request independe ntly . 3.8.1 Common Text Overlay Setting There are some important information can be embe dded into image, including date, time, and/or text. 52[...]

3.8.2 MPEG4/VGA Video T ype It’ s MPEG4 mode in this profile Resolution It’ s VGA mode (640x480) in this profile Bit rate Control Defines the rate cont rol method of this profile. There are two options: Constant Bit Rate (CBR) or V ariable Bit Rate (VBR). For CBR, the video bit rate is between 384kbp s and 4096kbps. Use r can set the desired bi[...]

3.8.3 MPEG4/QVGA Video T ype It’ s MPEG4 mode in this profile. Resolution It’s QVGA mode (320x240) in this profile. Bit rate Control Defines the rate control method of this profile. There are t wo options: Constant Bit Rate (CBR) or V ariable Bit Rate (VBR). For CBR, the video bit rate is between 128kbp s a nd 1024kbp s. User can set the desire[...]

3.8.4 MPEG4/QQVGA Video T ype It’ s MPEG4 mode in this profile. Resolution It’ s QQVGA mode (160x120) in this profile. Bit rate Control Defines the rate cont rol method of this profile. There are two options: Constant Bit Rate (CBR) or V ariable Bit Rate (VBR). For CBR, the video bit rate is between 24kbps and 320kb p s. User can set the desi r[...]

3.8.5 VIDEO/JPEG Video T ype It’ s JPEG mode in this profile. Resolution User can select VGA, QV GA, or QQVGA mode as the resolution of this JPEG profile. Rate Control The quality le vel is between 1 a nd 100. The highe r value is the better quality . Max Frame Rate Defines the targete d frame rate of th is profile. For example, set the frame rat[...]

3.9 Audio *hardware version 2 Audio T o enable or disable audio function Audio Mode T o select Simplex or Full duplex (2-way audio) mode Input Gain T o adjust gain of input audio Output Gain T o adjust gain of output audio 57[...]

3.10 User Use this menu to set the user names and p assword of the Administrator and up to 10 users, and access right of each user . Vie wer Login Anonymous Choose this to enable ano nymous u ser login. Only users in dat abas e Choose this to disable anonymous user login. User Name Enter the user ’s new account here which you want. Password Enter[...]

3.1 1 E-Mail You may setup SMTP mail parameters for further operation of Event Schedul e. That’s, if users want to send the alarm message out, it will need to configure parameters here and also add at least one event schedul e to enabl e event triggering. SMTP Server T ype the SMTP server name or the IP address of the SMTP server . Te s t Send a [...]

3.12 Object Detection Use this menu to specify motion detection wind ow 1 to window 4 and set the conditio ns for detection while observing a captured image. Add and Del T o add or delete the motion windows. User can sp ecify up to 4 Included and/or Excluded windows to monito r the video captured by this devic e. By dragging mouse on the image, you[...]

easier to trigger event. Sensitivity Defines the sensitivity value of motion detection. The higher value will be mo re sensitivity . 3.13 Event Server Setup FTP/TCP/HTTP server configuration 3.13.1 FTP Server You may setup FTP parameters for further operation of Event Schedule. That ’s, if users want to send the alarm message t o an FTP server, i[...]

3.13.2 TCP Server In addition to send video file to FTP server, the device also can sen d event message to specified TCP server. Name User can specify multiple TCP server s as wish. Therefore, use r needs to specify a name for each TCP se rver setting. TCP Serv er T ype the server nam e or the IP addre ss of the TCP server . TCP Port Set port numbe[...]

3.13.3 HTTP Server The device also can send event mess age to specified HTTP server. Name User can specify multip le HTTP servers as wish. Therefore, user needs to specify a name for each HTTP server setting. URL T ype the se rver name or the IP address of the HTTP server . Te s t Check the HTTP server whether it is available or not. HTTP Login Nam[...]

3.14 Event Schedule This menu is used to specif y the sched ule of Ev ents and activate the some actions provided b y this device.  Name Name of the Event or Schedule. Enable Enable or disable this Event or Schedule. Ty p e Schedule st art with Event trigger or Sche dule trigger . Enable Time Define the feas ible time slot. T rigger by Select th[...]

Appendix A: Reset Factory Default Settings This button is used to restore the factory default settings. Sometime s restarting the ICA-10 8/108W will make the system back to a normal state. If t he system still got problem s after reset, user can restore the factory default settings and i nstall it again. Restore the ICA-350: 1. Loosen these two scr[...]

66 3. Press and hold the button down contin uously. 4. Wait at least 10 seconds and release th e button. Then the ICA-35 0 has been restored to factory default settings and reboot again.[...]

Appendix B: PING IP Address The PING (stands for Pa cket Internet Groper) co mmand is used to detect whether a specific I P address is accessi ble by sending a packet to t he specific add ress and waiting for a reply. It’s also a very useful tool to confirm ICA-350 insta lled or if the IP address conflicts with any other devices over the network.[...]

Appendix C: Bandwidth and Video Size Estimation The frame rate of video transmitted from the ICA-350 depends on connection bandwidt h between client and serve r, video resolution, code c type, and quality setting of server. Here is a guideline to help you roughly estimate the bandwidth requirements for your ICA -350. The required bandwidth depen ds[...]

MPEG4 Resolution Stream setting fps setting Current stream Current fps 640*480 VGA 384Kbps 5 fps 373Kbps - 388Kbps 5 fps 640*480 VGA 1024Kbps 5 fps 1024Kbps - 1036Kbp s 5 fps 640*480 VGA 2048Kbps 5 fps around 1800Kbps 5 fps 640*480 VGA 384Kbps 20 fps around 550Kbps 22 fps 640*480 VGA 1024Kbps 20 fps around 1400Kbps 20 fps 640*480 VGA 2048Kbps 20 fp[...]

Appendix D: DDNS Application 1. Preface If you have a Cable modem or xDSL, this is a great way to host your own Networked Device or other TCP/IP Service. Get your own domain like www.yourname.com, www.yourname.com.tw etc. (N ote: This domain must be re gistered with Internic via registration authorities su ch as Network Solu tions, DirectNI C, Regi[...]

3. Application Step s – DDNS & Domain Name (1). Visit the following web site: http://www .dyndns.org/ (2). Click “ Account ” (3). Af ter the columns show up at the le ft side, click “ Create Account”. 71[...]

(4). Fill the application agreement and nece ssary information. a. Username b. E-mail address and confirmation c. Password and confirmation d. Submit all the input information and finish creating an acco unt Click these two options 72[...]

(5). Check your e-mail mailbox. There will be an e-mail with a title “Y our DynDNS Account Information“. Click the hyperlink address to confirm the DDNS se rvice that you just applied. Then DDNS you applied activated. Click to confirm (6). Enter the web page http://www .dyndns.org/ again. Input your username and passwo rd that you just applied [...]

(7). If the correct username and pa ssword are input, you can see the following picture at the top-right of the login page. (8). Click the “ Services”. (9). Click the “ Dynamic DNS ”. (10). Click the “ Create Hosts ”. 74[...]

75 (1 1). We could create a do main name without any charge at this step. First, we input the host name. (No.1) Then we pick a domain that is easy to remem ber . Finally (No.2), click the “Add Host” to submit the domain name informatio n. (No.3) 1 3 2 4. Setup the DDNS and PPPoE of Network Device At last, users have to enter the web page of Net[...]