Precor RBK 615 . UBK 615 Bedienungsanleitung

Pr oduct Owner ’ s Manual RBK 6 15 • UBK 6 15 Prec or Incorpor ated 20031 142nd A venue NE P .O . Box 7 202 W oodinville, W A USA 980 72 -4002 XBK 615 POM 302 217 - 101 rev A December 2012[...]

[...]

[...]

Edition Information UBK / RBK 615 PRODUCT OWNER ’ S MANU AL P/N 302217 - 101 rev A Copyright © December 2012 Precor Incorporated. All rights reserved. Specifications subject to change without no tice. Trademark Note Precor, AMT, EFX, and Pre va are registered trademarks of Precor Incorporated. Ot her names in this document may be the trademarks [...]

Important Sa f ety Instructions Importan t: Save these instru ctions for future reference. Read all instructions in the documentation provided with your ex ercise equipment, including all assembly guides, user guides, and o wner ’ s manuals, before installation of this device. Note: This product is intended for commercial use. The display apparat[...]

4 Product Owner's Manual Safety Preca utions Always follow basic safety precautions when using this equipment to reduce the chance of injury, fire, or damage. Other sections in this manual provide more details of safety features. Be sure to read these sections and observe all safety notices. These precautions include the following:  Read al[...]

Important Safety Instructions 5  Care should be taken when mounting or di smounting the equipment.  For Treadmills: Do not use ty ping or web surfing features while walking at speeds that exceed a slow and relaxe d leisurely pace . Always stabilize yourself by holding a stationary handle bar while using typing or web surfing features.  For[...]

6 Product Owner's Manual  SPACING— The below minimum spacing recommendations are based on a combination of the ASTM (U.S.) voluntary standar ds and EN (European) regulations as of October 1, 2012, for access, passage around, and emergency dismount:  Treadmills— a minimum of 0 .5 m (19.7 in.) on each side of the treadmill and 2 m (78 [...]

Important Safety Instructions 7  Maintain the equipment to keep it in good working condition, as described in the Maintena nce section of the owner ’ s manual. Inspect the equipment for incorrect, worn, or l oose components, and then correct, r eplace or tighten prior to use.  If you plan to move the equipment, obtain help and use proper li[...]

8 Product Owner's Manual Educ ating Users Take time to educate use rs about the Important Safety Instructions found in bot h the User Reference M anual and Product O wner ’ s Manual . Explain to your club or facility patrons that they should obser ve the following precautions:  Hold onto a stat ionary handrail or handlebar while assuming [...]

Important Safety Instructions 9 Regulatory Notic es for the RFID Module When equipped with a control c onsole as described in this document, this equipment may include a radio - frequency identification (RFID) module. The RFID module has been certified to operate at temperatures between - 20°C and 85°C (- 4°F and 1 85°F). Radio Frequency Interf[...]

10 Product Owner's Manual Industry Canada This device complies with RSS - 210:2007 of the Spectrum Management & Telecommunicat ions Radio Standards Specification. Operation is subject to the following two conditions: (1) this device m ay not cause harmful interference, and (2) this device must accept any interference received, including in[...]

Important Safety Instructions 11 Regulatory Notic es for Cardiovascular Exercise Equipment The regulatory information in this s ection applies to the exercise equipment and its control console. Safety Approvals for Cardiovascular Equipment Precor equipment has been teste d and found to comply with the following applicable safety standards. Cardiova[...]

12 Product Owner's Manual Industry Canada This Class A digital apparatus complies with Canadian ICES - 003. Cet appareil nu mérique de la class e A est con forme à la no rme NMB - 003 du Canada. ATTENTION: H aute Tensio n Débranche z avant de r éparer European Applications CE compliance is claimed to the following directives:  2004/108/[...]

Important Safety Instructions 13 Electrical Recommend ations: All Equipment Excluding Treadmills Note: This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. For equipment fitted with a P80 console or Personal Viewing System (PVS) screen a separate power connection is required. For a [...]

14 Product Owner's Manual Obtaining Service Do not attempt to service the equipment except for maintenance tasks. If any items are missing, contact your dealer. For more information regarding customer support numbers or a list of Precor authorized service centers, visit the Precor web site at http:// www.precor.co m. Obtaining Updat ed Documen[...]

T able of C ont ents Important Safety Instructions .................................................... 3 Safety Precautions ................................................................................ 4 Educating Users .................................................................................... 8 Hazardous Materials and Proper Disposal[...]

16 Product Owner's Manual[...]

Chapter 1 Pr oduct F ea tur es This section is designed t o show you how to customize the eq uipment for your users and view us eful product information. All these features remain hidden to the users and can only be accessed using special keypresses. These custom settings allow you to  Change the display to a different language  Change the di[...]

18 Product Owner's Manual Table 1. Cus tom feat ures and s ettings for your fit ness equi pment Equipment Programming Prompt Factory Default Setting Features you c an change All * SELECT LANGUAGE English Select one language for your user. All * SELECT UNITS U.S. Two standard units of measu rement are available. Choose U.S. or Metric. All * SET[...]

Product Features 19 Programming Tips  Always start at the Precor banner.  Electrical power must be supplied. For self - pow ered equipment, a constant power sourc e is available if you use the optional power adapter. Otherwise, users have to maintain the minimum rate of motion. If you plan to program self - powered equipment, purchasing the o[...]

20 Product Owner's Manual Changing the Product Settings You must be in the Programming mode before you can change the settings. To access the progra mming mode: 1. At the Precor banner, press t he follow ing keys in sequence without pausing between selections: RESET, 5, 6 , 5, 1, 5, 6 , 5 Note: A PAUSE/RES ET key appears on some products and f[...]

Produc t Features 21 Table 2. Programming mode keys Key Descripti on ▲ or ▼ Navigational arrows: Move you through the menu and can also be used to increase or decrease time units. OK Press to choose o r accept the dis played selection. Nu mber keypad CLEAR Returns user to the previous menu level without saving changes. PAUSE/RES ET Exits Progra[...]

22 Product Owner's Manual Use the following flowchart t o navigate through the menu settings. Figure 3 : Bike m enu se tting s Choosing a Language The equipment can display user prompts, text, and user entries in several different languages. When the equipment is shipped from the factory, the default language is English. Note: Programming prom[...]

Product Features 23 Selecting a U.S. Standard or Metric Display The equipment can display measurements in either Metric or U.S. Standard. The defa ult factory setting is U.S. Standard. To change the display measurement : 1. At the SEL ECT UNITS prompt, press OK. Use th e navigational arrow keys to select a unit of measure ( US or METRIC ). Press OK[...]

24 Product Owner's Manual Setting a Pause Time Limit You can limit how long a user can pause while exercising on the equipment by entering a time between 1 and 120 seconds (two minutes). For example, if you set a pause time limit of 60 seconds, the display automatically resets to the Precor banner if no movement is detected and no key press oc[...]

Product Features 25 Setting a Resistance R ange The bike resistance levels are low, medium, and high. Within each setting, 25 levels of resistance are available, but the chosen setting affects the overall resistance range. To set a resistance range: 1. At the SET RESISTANCE RANGE prompt, press OK and use the navigational arrow keys to choose LOW , [...]

26 Product Owner's Manual Informational Displays Use the information displa ys to locate information about equipment use (odometer and hour meter), software versions and part numbers, serial number, usage log, and error log. In general, you would only access this information if directed to do so by Precor Customer Support. To navigate through [...]

Product Features 27 Note: The C LEAR key is located on the number keypad. If your product has a PAUSE/RESET ke y, use it in place of the RESET key called out in the flowchart.[...]

28 Product Owner's Manual Table 4. Informational D isplays for all pro ducts Product Displ ay Desc ription All HOUR METER • The number of hours that the equipment has been in u se. • The equipment tracks th e elapsed minutes, but the value that appears is truncate d to the nearest full hour. All U - BOOT SW Upper bo ard appli cation so ftw[...]

Product Features 29 Product Displ ay Desc ription All ERROR LOG Displays any e rror co des that may have been detected by th e software. All ODOMETER The odometer value correlates t o the type o f Precor produ ct and the standard o f units , U.S. or Me tric, selected in the programs . • Treadmill shows the nu mber of cumulative miles or kilo mete[...]

30 Product Owner's Manual Erasing the Error Log When you no longer need the error l og information, you can erase the entries. To erase the error log entries: 1. Press QUICKSTART while any error description is scrolling across the display. 2. Continue to maintain light pressure on the key until the message HOLD TO CLEAR ERRORS scrolls off the [...]

Chapter 2 Educating Users This console offers an easy- to - follow displa y and multiple programs to help users meet their workout needs. The keypad lets them select data and control their workout session and S martRate® provides a visual aid that monitors heart rate and workout intensity at a glance.[...]

32 Product Owner's Manual Using SmartRate® The Precor SmartRate® technology is a precise, easy - to - read heart rate monitor that helps users achieve their best personalized workouts. SmartR ate displays actual heart rate information in relat ion to the user ’ s target zone for weight loss and cardiovascular training. This feature is visi[...]

Chapter 3 Displa y Console The display console is designed for ease of use. Use the following graphic and ta ble to learn more about the console displays. Figure 4 : Cons ole parts[...]

34 Product Owner's Manual Table 5. Parts of the display cons ole Number Description HEART RATE dis play : Use a chest strap or grasp both touch - sensitive grips to display and monitor your pulse. Center dis play : Initially shows the Precor banner. It changes to the program profile when you select a program or press QUICKSTART. A blinking col[...]

Display Console 35 Using the Upper Display The program profile suppli es information about your programmed workout. A blinking segment in the profile indicates your position. The profile raises or lowers if you change your resistance. Figure 5 : Parts of the progr am profile Keypads Use the keypads to enter program selections and display preference[...]

36 Product Owner's Manual PRO GRAMS Keypad The PROGRAMS keypad provides access to all t he exercise programs. To use th e program k eypad: 1. Press the center of the key to view the top level program in its menu. 2. Press the OK key to confirm your selection. Table 6. Available program s PROGRAMS Key P rogram Menu MANUAL MANUAL INTERVAL INTERV[...]

Display Console 37 Number Keypad The number keypad has several functions depending on what is connected to the equipment. Table 7. Connections Connection Descripti on Computer (CSAFE compatible) If a computer is attached to the CSAFE connection on the equipment, the number keypad le ts you enter your user ID and answer other setup prompts. Entertai[...]

38 Product Owner's Manual The CLEAR and ENTER keys provide the following functions: CLEAR: Use the CLEAR key to remove the last num ber being displayed. ENTER: Use the ENTER key to accept the number being displayed. Note: The OK and ENTER keys are usu ally interchangeable and provide the same function when no peripheral devices are attached to[...]

Chapter 4 W ork out Options CAUTION: B efore beg inning any fitness p rogram, se e your physician fo r a com plete phy sical exam ination. Know yo ur physici an - recommended he art rate target zone. To begin y our worko ut: 1. Face the display. 2. Hold on to a handlebar and step on the foot peda ls. 3. When you are comfortably situated, begin peda[...]

40 Product Owner's Manual Choosing QUICKSTA RT Use the Quickstart feature to begin an immediate workout. To use this feat ure: 1. Begin pedaling. 2. While the Precor banner scrolls, press QUICKSTART to begin the Manual Program. Figure 6 : QUIC KSTART bu tton QUICKSTART applies the following defaults: Prompts De fault Val ue Program Manual Time[...]

Workout Options 41 Selecting a Program 1. While the Precor banner scrolls, press a PROGRAMS key, and then press OK. 2. A time prompt blinks in the display. Use the navigational arrow keys or the number keys to adjust the minutes (1 – 240) and then press OK. (Or, press CLEAR to return to the default time limit.) Note: Because the fitness facility [...]

42 Product Owner's Manual Storing Wo rkout St atistics In some fitness facilities, Preco r equipment is connected to a computer so that you can easi ly retrieve your workout statistics and determine how well you are meeting your fitness goals. If you are interested in maintaining workout statistic information, ask the manager to create a user [...]

Workout Options 43 Changing Programs in Mid -session You can change programs in the middle of a session by s electing a new program from the PROGRAMS key menu and pressing OK. All ac cumulated statistics are tra nsferred to the new program as you continue exercising. Certain programs, such as Ba sic HRC and Weight Loss, ar e not available for mid -[...]

44 Product Owner's Manual Pausing During a Workout or th e Cool - Down Period If your rate of motion drops below minimum requirements while exercising or during the cool down period, a 30 - second shutdown is initiat ed. You cannot pause for a longer period of time or change to a different program unless the fitness facility has the optional p[...]

Chapter 5 Pr og r ams This section describes the p rograms available on the equipment. Use the following table to learn more about each workout program.[...]

46 Product Owner's Manual Graphic Program He ading Workout Det ails Manual This workout begins as a flat line. You can increase or decrease the resistance using t he resistance key. The workout profile reflects changes yo u make an d a bli nki ng light in the column indicates your position in t he workout. Interval These workouts raise and low[...]

Programs 47 Program Tips  Begin at the Precor banner a nd choose a program by pressing a PROGRAMS key or QUICKSTART.  While exercising, you need to sustain your exercise motion. Stopping any movement caus es the equipm ent to shut down to conserve battery po wer.  A blinking column indicates your position as you progress through a workout.[...]

48 Product Owner's Manual Notes:[...]

[...]

Pr oduct Owner ’ s Manual RBK 6 15 • UBK 6 15 Prec or Incorpor ated 20031 142nd A venue NE P .O . Box 7 202 W oodinville, W A USA 980 72 -4002 XBK 615 POM 302 217 - 101 rev A December 2012[...]

As sembling and Maintaining the UBK 6 15 Upright Ex er cise Bik e Prec or Incorpor ated 20031 142nd A venue NE P .O . Box 7 202 W oodinville, W A USA 980 72 -4002 UBK 615 P AG/ OM 30 2209- 101 r ev A W arr anty #36286- 114 December 2012[...]

[...]

[...]

Edition Information ASSEMBLING AND MAI NTAINING THE UBK 615 UPRIGHT EXERCISE BIKE P/N 302209- 101 rev A Copyright © December 2012 Precor Incorporated. All rights reserved. Specifications subject to change without notice. Trademark Note Precor, AMT, EFX, and Pre va are registered trademarks of Precor Incorporated. Ot her names in this document may [...]

Important Sa f ety Instructions Importan t: Save these instru ctions for future reference. Read all instructions in the documentation provided with your exercise equipment, including all assembly guides, user guides, and o wner ’ s manuals, before installation of this device. Note: This product is intended for commercial use. The display apparatu[...]

4 Assembling and Maintaining the UBK 615 Upright Exercise Bi ke Safety Preca utions Always follow basic safety precautions when using this equipment to reduce the chance of injury, fire, or damage. Ot her sections in this manual provide more details of safety features. Be sure to read these sections and observe all safety notices. These precautions[...]

Important Safety Instructions 5  Care should be taken when mounting or di smounting the equipment.  For Treadmills: Do not use ty ping or web surfing features while walking at speeds that exceed a slow and relaxed leisurely pace . Always stabilize yourself by holding a stationary handle bar while using typing or web surfing features.  For [...]

6 Assembling and Maintaining the UBK 615 Upright Exercise Bi ke  SPACING— The below minimum spacing recommendations are based on a combination of the ASTM (U.S.) voluntary standar ds and EN (European) regulations as of October 1, 2012, for access, passage around, and emergency dismount:  Trea dmills— a minimum of 0.5 m (19. 7 in.) on each[...]

Im portant Safety Instructi ons 7  Maintain the equipment to keep it in good working condition, as described in the Maintena nce section of the owner ’ s manual. Inspect the equipment for incorrect, worn, or loose components, and then correct, replace or tighten prior to use.  If you plan to move the equipment, obtain help and use proper li[...]

8 Assembling and Maintaining the UBK 615 Upright Exercise Bi ke Educating Users Take time to educate use rs about the Important Safety Instructions found in bot h the User Reference M anual and Product O wner ’ s Manual . Explain to your club or facility patrons that they should observe the following precauti ons:  Hold onto a stationary handr[...]

Important Safety Instructions 9 Regulatory Notic es for the RFID Module When equipped with a control c onsole as described in this document, this equipment may include a radio - frequency identification (RFID) module. The RFID module has been certified to operate at temperatures between - 20°C and 85°C (- 4°F and 1 85°F). Radio Frequency Interf[...]

10 Assembling and Maintai ning the UBK 615 Upright Exercise Bike Industry Canada This device complies with RSS - 210:2007 of the Spectrum Management & Telecommunicat ions Radio Standards Specification. Operation is subject to the following two conditio ns: (1) this device may not cause harmful interference, and (2) this device must accept any i[...]

Important Safety Instructions 11 Regulatory Notic es for Cardiovascular Exercise Equipment The regulatory information in this section applies to the exercise equipment and its control console. Safety Approvals for Cardiovascular Equipment Precor equipment has been teste d and found to comply with the following applicable safety standards. Cardiovas[...]

12 Assembling and Maintai ning the UBK 615 Upright Exercise Bike Radio Frequency Interference (RFI) This Precor exercise equipment conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been test ed and found to comply with the lim[...]

Important Safety Instructions 13 Electrical Recommend ations: All Equipment Excluding Treadmills Note: This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. For equipment fitted with a P80 console or Personal Viewing System (PVS) screen a separate power connection is required. For a [...]

14 Assembling and Maintaining t he UBK 615 Upright Exercise Bi ke Obtaining Service Do not attempt to service the equipment except for maintenance tasks. If any items are missing, contact your dealer. For more information regarding customer support numbers or a list of Precor authorized service centers, visit the Precor web site at http:// www.prec[...]

T able of C ont ents Important Safety Instructions .................................................... 3 Safety Precautions ................................................................................ 4 Educating Users .................................................................................... 8 Hazardous Materials and Proper Disposal[...]

16 Assembling and Maintaining t he UBK 615 Upright Exercise Bi ke Self - Powered Features .............................................................. 41 Informational Displays Pr ior t o Shut down .................................. 42 Symptoms of a Low Batter y ............................................................ 42 Using the Optional Po[...]

Chapter 1 As sembling the Ex er cise Bik e Importan t: The instruc tions in the follow ing procedu res are described f rom the perspective o f a person stan ding directly i n front of the equ ipmen t (that is, on the op posite side of th e control con sole from a perso n using th e equipment). Th ese descriptions m ay not match th e names of cer ta[...]

18 Assembling and Maint aining the UBK 615 Upright Exercise Bike Unpacking the Equip ment The shipping container for this exercise bike consists of the following items:  Wooden pallet  Cardboar d base  Cardboard cover  Foam sp acers WARNING Do not atte mpt to mo ve the e quipment o ff of the pallet b y yourse lf. Have at least one other[...]

Assembling the Exercise Bike 19 Hardware Kit (not to sc ale) Before you begin the assembly, verify that the following hardware items are packed with the equipment. Fasteners Quantity M12 x 80 mm sockethead screw 2 M8 x 25 mm sockethead screw 4 M10 x 40 mm buttonhea d screw 4 ¹₄ - inch x ³₄ - inch buttonhead screw 4 M5 x 12 mm panhead sc[...]

20 Assembling and Maintaining the UBK 615 Upright Exercise Bike Required Tools  6 mm hex wrench  10 mm hex wrench  ⁵₃₂ - inch hex wrench  13 mm open - end, box, or socket wrench  17 mm open - end wrench  #2 Phillips screwdriver  Wire cutter  Fish tape Installing the Stabilizers The two stabilizers containing the fee[...]

Assembling the Exercise Bike 21 2. Secure the rear stabilizer using two M10 x 40 mm bu ttonhead screws. Tighten the screws completely using a 6 mm hex wrench. Figure 3 : Rear stabilizer attachm ent 3. Place the front stabilizer underneath the bracket at the front of the bike. Figure 4 : Front s tabilizer install ation[...]

22 Assembling and Maintaining the UBK 615 Upright Exercise Bike 4. Secure the front stabiliz er using two M10 x 40 mm buttonhead screws. Tight en t he screws completely using a 6 mm hex wrench. Figure 5 : Front s tabilizer attachm ent[...]

Assembling the Exercise Bike 23 Attaching the Sea t Mount the seat onto the bracket at t he top o f the seat column. To attach the seat: 1. Place the seat on the bracket so that the three bolts extend through the screw holes. 2. Attach an 8.2 mm flat zinc washe r and an M8 nylon lock nut to each bolt. Tighten the fasteners completely using a 13 mm [...]

24 Assembling and Maintaining the UBK 615 Upright Exercise Bi ke Installing the Upright Support and Cables DANGER Do not attempt to con nect elec trical powe r until all assembly procedures a re comp lete and the console is properly i nstalled . Before you begin this procedure, retrieve the cables for the console that you plan to install on this ex[...]

Assembling t he Exercise Bike 25 7. Lift the upright support and position its lower end over t he upright support channel on the body assembly. Slide the support into positi on so that its screw holes line up with the corresponding holes on the bod y assembly, as shown in the following figure. Note: If the s upport is positioned corre ctly, it rest[...]

26 Assembling and Maintaining the UBK 615 Upright Exercise Bi ke 8. Insert the two M12 x 80 mm sockethead screws through the openings on the support and i nto the screw holes on the body assembly. Tighten the screws completely using a 10 mm hex wrench. Figure 8 : Bolti ng the uprig ht suppor t into place[...]

Assembling the Exercise Bike 27 Installing the Bottle Holder The bottle holder attaches direc tly to th e upright su pport. To install the bottle holder: 1. Position the bottle holder aga inst the upright support so that the screw holes in the bott le holder and the support line up. 2. Secure the bottle holde r onto the upright support using two M5[...]

28 Assembling and Maintaining the UBK 615 Upright Exercise Bi ke In stalling the Handlebars After the upright support and the bottle holder are securely in place, install the handlebar assembly and route the heart rate sensor cable through the support . To install the handlebars: 1. Place the handlebars on the arms of the upri ght support, as shown[...]

Assembling the Exercise Bike 29 2. Feed the end of the heart rate cabl e through the nearest arm of the upright support, t hen up through the support itself and out the openin g in the console mount, as shown in the following figure. Figure 11 : Cable rout ing thro ugh Displ ay C cons ole moun t[...]

30 Assembling and Maintaining the UB K 615 Upright Exercise Bike 3. Seat the handlebars on the upright support as shown in the following figure, storing extra cable in the upright support as n eeded. Figure 12 : Handleb ar installa tion 4. Place four 8.1 mm flat black was hers onto four M8 x 25 mm sockethe ad screws. Place the handlebar asse mbly o[...]

Assembling the Exercise Bike 31 Making Su re the Uni t Is Stable Make sure the unit is level before allowing anyone to use it. CAUTION: To eliminate moveme nt, make sure the ad justable feet are in con tact with t he floor. To level the un it: 1. Gently rock the unit. If there is any movement, ask your assistant to tip the unit to one side w hile y[...]

32 Assembling and Maintaining the UBK 615 Upright Exercise Bike Installing the C onsole Before you begin, make sure that the cables have been fed through the mounting bracke t and their ends extend thr ough the round opening at the base of the bracket. The television cable, along with any a udio, video, or power cables needed to support a Cardio Th[...]

Assembling the Exercise Bike 33 3. Retrieve the serial number label you removed from the body assembly earlier. Remove the backing from the label and apply it inside the console at the upper right, as shown in the following figure. Figure 14 : Serial numb er labe l locatio n[...]

34 Assembling and Maintaining the UBK 615 Upright Exercise Bike 4. Route the flat, black base unit data cable to the left of the mounting bracket and about t hree-quarters of the way up the left side of the console, as s hown in the following figure. Attach the base unit data cable to the eight - conductor modular jack labeled LOWER BOARD CONNECTIO[...]

Assembling the Exercise Bike 35 7. Lower the rear cover over the mounting bracket so that the upr ight support extends through the gap in the cover. Figure 16 : Rear cover positio n 8. Position the back cover and atta ch the four 1- inch panhead machine screws, then tighten th e screws completely using a #2 Phillips screwdriver. Figure 17 : Reatt a[...]

36 Assembling and Maintaining the UBK 615 Upright Exercise Bike Breaking in the Equip ment Precor equipment does not require an actual break - in period. However, moving components such as belts, gears, and bearings can settle while the equipment is being stored or shipped. This can cause the equipment to operate with a small amount of roughness or[...]

Chapter 2 Ma int enanc e To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklist. Failure to maintain the equipment as described in this section could void the Precor Limited Warr anty. DANGER To reduce the risk of e lectric al shock, a lways disconnect the [...]

38 Assembling and Maintaining the UBK 615 Upright Exercise Bike Alternatively, you can clean the equipment with Athletix fitness equipment cleaning wipes (for more information, visit www.athl etixproducts.c om ) CAUTION: Re ad and follow the manufactur er ’ s inst ructions, particularl y dilution instruct ions, bef ore using a ny clean er on Prec[...]

Maintenance 39 Quarterly Maintena nce Precor recommends that you clean and inspect the equipment more thoroughly once every three months. To perfor m quarterly ma intenanc e: 1. Remove the cover panels. 2. Vacuum out any debris, being careful not to bring the vacuum cleaner nozzle too cl ose to any circuit board (unless your vacuum cleaner is prote[...]

40 Assembling and Maintaining the UBK 615 Upright Exercise Bike Moving the Equi pment The equipment is very heavy. If you plan to move it t o a new loca tion, obtain the help of an adult assista nt and use proper lifting techniques. If the equipment includes roller wheels on one end, use the wheels to reduce the load on y ourself and your assistan [...]

Chapter 3 Self- Po w er ed Fe atur es Important : This chapter of the manual d escribes Precor fitness equipment that c an operate w ithout being c onnected to AC power. This in cludes units eq uipped with P30 o r P10 consoles . However, P80 co nsoles must be c onnected to A C power throu gh their power s upplies to oper ate. For this re ason, this[...]

42 Assembling and Maintaining the UBK 615 Upright Exercise Bike Informationa l Displays Prior to Shut down The equipment saves its battery charge by moving into a shutdown mode. If the user does not mainta in the minimum rate of motion, a 30- second shutdown proce ss begins. In this mode, the console displa ys a countdown indicator and ignores all [...]

Self- Powered Features 43 Using the Optional Po wer Adapter After connecting t he power adapter to the equipment, pl ug the opposite end into the appropriate power source (120 V or 240 V). CAUTION: Whe n the optional power adapte r is in use, make sure that the po wer supp ly cord do es not cre ate a safety hazard . Keep it out of t he way of traff[...]

44 Assembling and Maintaining the UBK 615 Upright Exercise Bi ke Replacing the Battery The equipment ’ s battery is built to last for a long time. However, if you feel that the battery may need replacing, check with an authoriz ed service technician. Refer to Obtaining Servic e . C AUTION: Th e battery stored ins ide the equipmen t contains hazar[...]

Chapter 4 C ommer cial Car dio v ascular E quipment Li mit ed W arr anty PLEASE READ THESE W ARRANTY TERMS AND CONDITIONS CAREFUL LY BEFORE USING YOUR PRE COR INCORPORAT ED PRODUCT. BY U SING THE EQUI PMENT, YOU ARE CONSENTING TO BE BO UND BY THE FOLLOWING WARRANTY TERMS AN D CONDITIONS . Limited Warranty. Precor Incorp orated warran ts all new Pre[...]

46 Assembling and Maintaining the UBK 615 Upright Exercise Bi ke Options / Accesso ries Many options or acc essories have comp onents that are connect ed internally or mounted inside the electronic console. The following guidelines determine the wa rranty for these components. If the inter nal components ar e installed by the fa ctory or by an auth[...]

Commerci al Cardiovascular Equipment Limite d Warranty 47 This Limited Warranty shall not apply to: 1. Software ver sion upgrade s. 2. Software defe cts that do not materially and negatively affe ct the normal p erformance of the product under nor mal conditions of us e. 3. Consumable goods or c osmetic items of the produc t, the exterior of whi ch[...]

48 Assembling and Maintaining the UBK 615 Upright Exercise Bike EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES. PRECOR AND/OR ITS SUPPLIERS SH ALL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARI SING IN CONT RACT (INCLUDING WARRANTY), TORT (INCLU DING ACTIVE, PASS IVE, OR IMPUT ED NEGLIGEN CE AND STRICT L IABILITY), O R OTHERWISE, FOR D AMAGE TO TH[...]

[...]

As sembling and Maintaining the UBK 6 15 Upright Ex er cise Bik e Prec or Incorpor ated 20031 142nd A venue NE P .O . Box 7 202 W oodinville, W A USA 980 72 -4002 UBK 615 P AG/ OM 30 2209- 101 r ev A W arr anty #36286- 114 December 2012[...]