Precor TRM 800 Bedienungsanleitung

As sembling and Maintaining TRM 800-Series T r eadmills Prec or Incorporated 20031 142nd A venue NE P .O . Box 7 202 W oodinville, W A USA 98072-400 2 TRM 800-Series P AG/ OM 300713-341 r ev G W arranty #36286- 114 14 F ebruary 2011[...]

[...]

[...]

Edition Informa tion ASSEMBL ING AND MAI NTAININ G TRM 800 - SERIES TREADMI LLS P/N 30 0713 - 3 41 rev G Copyrig ht © Febru ary 2 011 P recor In corpo rate d. Al l rig hts reserved. Specifications subject to change without no tice. Trademark Not e Precor, AMT, and EFX are registered trademarks and Preva is a trademark of Precor Incorporate d. Othe[...]

Important Sa f ety Instructions Read the following precaut ions thoroughly before you begin assembly, and save them afterward fo r future r eference. Safety Precautions Always follow basic safety precautions when using this equipment to reduce the chance of injury, fire, or damage. Other sections in this man ual provide more details of safety featu[...]

4 Assembling and Maintain ing TRM 800 - Series Treadmills  Use the power adapter provided with the equipment. Plug the power adapte r into an appropriat e, grounded po wer outlet as ma rked on the equipmen t.  Care should be taken whe n mounting or dismounting the equipmen t.  Read, understand, and test the emergency stop procedures before[...]

Important Safe ty Instructions 5  When using the tr eadmill, always attach the sa fety clip to your clothing before begin ning your workout. Failure to use the safety clip may pose a greater risk of injury in the event of a fal l.  Also, verify that the running belts on treadmills are clean and running smoothly.  Do not allow runners over [...]

6 Assembling and Maintain ing TRM 800 - Series Treadmills Educatin g U sers Take time to edu cate users ab out th e Imp ortant Safety Instructions found in both the User Reference Manual and Product Owne r ’ s Ma nu al . Explain to you r club or facility patrons that they should observe the f ollowing precautions:  Hold onto a stationary han d[...]

Important Safe ty Instructions 7 Product Recyclin g and Disposal This equipment must be re cycled or discarded accordi ng to applicable local and nation al regulations. Product labels, in accordance wit h European Directive 200 2/96/EC concerning waste electrica l and electronic equipmen t (WEEE), de termine the framewor k for the return and recycl[...]

8 Assembling and Mainta ining TRM 800 - Series Treadmills Ra dio Fr equency Interf erence ( RFI) The RFID module conforms to the following national standards defining acceptable limit s for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been t ested and found to comply with the limits for a Cl ass [...]

Important Safe ty Instructions 9 European Applications CE compliance is claimed t o the following directives:  1999/ 5/EC R&TTE Dire ctive  2006/9 5/EC LVD Dir ective  2002/95/EC RoHS Directive Directive compliance has been verifie d to the following standard s:  EN 55022  EN 300 330 - 1 V1.5.1  EN 300 330 - 2 V1.3.1  EN 30[...]

10 Assembling and Maintainin g TRM 800 - Seri es Treadmills Radio F requenc y Inter ference ( RFI) This Precor exercise equip ment conforms to the follo wing national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been t ested and found to comply wit h the l[...]

Important Safe ty Instructions 11 Treadmill Grounding Instructions The tread mill must be grounde d. If the equip ment malfunctions or breaks do wn, grounding draws off elect ric curren t and reduces the risk of electric shock. The power co rd on the treadmill is equippe d with a grounding conduc tor and a three - pin grounding plug. This plug must[...]

12 Assembling and Maintaining TRM 800 - Seri es Treadmills Impo rtan t : An indivi dual branch c ircuit prov ides a hot c ond uctor and neutr al conductor to a receptac le. The co nductors m ust not be looped, "dai sy - chained", or connec ted to any o ther condu ctors. The circuit must be gro unded accor ding to NEC guideline s or local [...]

T able of Cont ents Import ant Safety Instr uctio ns ................................................... 3 Safety Pr ecautions ................................................................................. 3 Safety Code ............................................................................................ 5 Educating Users ................[...]

14 Assembling and Maintaining TRM 800 - Seri es Treadmills Maintena nce ............................................................................ 45 Daily Cleaning ..................................................................................... 45 Da ily Ins p ecti on .........................................................................[...]

Chapter 1 As sem bling the T r eadmill Import ant: The instructi ons in the following procedures are described from the perspecti ve of a person standing directly in front of the equipment (that is, on the oppo site side of the control cons ole from a per son usi ng the equ ipmen t). These descriptions may not match the n ames of certain parts in t[...]

16 Assembling and Maintaining TRM 800 - Seri es Treadmi lls 5. Remove the shipping fasteners from the front panel using a ¹₄ - inch hex key and a ¹⁄₂ – i nch box - end wrench. 6. Remove any tape or wire ties securing the console cable to the side of the uni t. Before you begin, verify that you have received the following parts:  Bas[...]

Assembling the Trea dmill 17 Hardware Kit (not to scale) The hardware kit shi pped with this equipment contains the fasteners and other hardw are components shown in the following table. Before you begin assembly, make sure that your hardware kit is comp lete. If not, please contact P recor Customer Sup port. Fasteners Q uantity Power cord c lips 6[...]

18 Assembling and Maintaining TRM 800 - Seri es Treadmi lls Unpacking the Cables To connect the console to the base unit, you may nee d up to five cables, as follows:  Ethernet ( P80 only)  Televisio n (P80 onl y)  Power (P 80 only)  Base unit data  Automatic stop sensor (Auto St op ™ ) The first three of these cables are shipped w[...]

Assembling the Trea dmill 19 3. Remove the seven screws holding the back cover in place. Snap the back cover loose and set it aside, along wit h the seven screws. Figure 4: Removal and repla cement of th e rear fai ring co ver 4. Remove the two ends of the ba se unit data cabl e from the left arm of the fairing (position 1 in the following illustra[...]

20 Assembling and Main taining TRM 800 - Series Treadmi lls 6. Remove any tape or ties that secure the cables, then unwind them and remove any kinks. Gather the cables into a single bundle (referred to later as the cab le assembly ). Note: Ar ranging the cable s so that the connectors a re slightl y staggered at the bottom end (but s till within on[...]

Assembling the Trea dmill 21 3. Se cure the right - hand upri ght support to the side bra cket using four socket head scr ews, four black washers, a nd two locknuts. Partially tighten t he fasteners. Figure 7 : Upright s upport attac hment, right side 4. Using t he fabric connectors provided, att ach the power supply to the right - hand side of t h[...]

22 Assembling an d Maintaining T RM 800 - Series Trea dmi lls To thread c ables through the fram e: 1. Feed the cable assembly downward through the left - hand upright support and out through the opening i n the lower end of the support. Drape the remaining cable over the front of the support and tape it into place if necessa ry to secure it tempor[...]

Assembling the Trea dmill 23 Component Appearanc e Lower connection point Televi sion c able R ound with b lack insula tion Conso le po wer cable Dual le ads with r ed and black insu lation Auto St op se nsor cable Round with b lack insu lation Power supply Re ctangu lar , black , 5" x 2 ¹₄ " x 1 ¹₄ " CAUTION: Be careful [...]

24 Assembling and Mainta ining TRM 800 - Series Treadmi lls 7. Route the cable assemb ly through the cable guides i n th e fairing, then wrap the guid es around the cable assem bly to secure it. Push any extr a cable into the up right support. Note: In the following step, use the zinc - finish buttonhead screws and flat wash ers from the hardware k[...]

Assembling the Trea dmill 25 Comple ting As sembl y After the upright supports and the f airing are in place, rep lace the hood on the treadmil l base and finish securing t he fasteners. CAUTION : Be a ware o f the handrail ext ensions when yo u are working around the front of the unit. It is ea sy to bump your head or sustain other injuries if you[...]

26 Assembling an d Maintaining T RM 800 - Series Trea dmi lls Note: Using a hex wrench, reach through the opening s in the outer sides of the hood to tighten the side screws. Figure 11 : Hood and fas tener placement Attaching the Power Cord Clips This treadmill includes a set of clips that hold the po wer cord away fro m the incline lift movement a[...]

Assembling the Trea dmill 27 2. Insert the serrated portion of the clip into the hole locat ed under the front of the unit on either side of the power switch. Figure 13 : Power cord placement unde r front of treadmill 3. Place the clips along the length of the powe r cord as needed while you direct the cord to the power outlet. T he holes, found in[...]

28 Assembling and Mainta ining TRM 800 - Series Treadmi lls Leveling the U nit The treadmill deck must be absolutely level from side to side to keep the belt in alignm ent and ensure proper operation. If the load is not equally dist ributed across the treadmill deck, users may feel excessive vibration or observe it at the console. You must make sur[...]

Assembling the Trea dmill 29 4. Adjust the rear feet as nee ded. Figure 16 : Level ing foo t adju s tment 5. Repeat steps 1 through 4 until the treadmill is level. 6. If necessary, adjust the rear feet so that the user’s weight is distributed evenly on the treadmill. Plugging In the Power Cord CAUTION : Use the supplied power cord. Do not remove [...]

30 Assembling and Mainta ining TRM 800 - Series Treadmi lls[...]

Chapter 2 Installing the Console To make installation easier, all Precor Experience Series consoles use the same mo unting hardware and connect or locations whenever possible. The i nstallation sequence for any of them is as fo llows:  Threading the cable assembly  Connecting cables  Completing the installation (tighteni ng the mounting sc[...]

32 Assembling and Maintainin g TRM 800 - Seri es Treadmills Impo rtan t : Before yo u begin the followin g procedure, re move the rear cover fr om the con trol console . To remove the cover, use your fingernails to pry th e l ower edge lo ose, then sw ing the co ver up and out as sh own in the following i llustration . Figure 17 : Rem oving the a c[...]

Installing the Con sole 33 4. Tilt t he console forward un til it stops. Use one hand t o steady the console in this position, or ask your assist ant to do so. 5. Using a #2 Phillips screwdriver, remove the two #8 - 32 x ¹₂ ” pan - head machi ne screws securing the upper back cover of the fairing, as shown in the previous figure. Set the co[...]

34 Assembling and Maintain ing TRM 800 - Series Treadmills Cable Conne ctor Type Circu it Conne ctor Location TV in F- type c oax ial Power Two - c ontac t plug, polari zed a nd la tche d Data fro m base unit Eight - co ntac t modu lar, on flat gray cable Heart rate s enso rs Four - c onta ct str ip, ke yed Safety key (trea dmil ls only) Six - co n[...]

Installing the Con sole 35 The following illustration s hows how the cable is posi tioned once i t is install ed. Figure 20 : Connecting the television cable Connecting the Ethernet and Base Unit Data Cables Both the Ethernet and base unit data cables pass thr ough the cutaway opening at the up per right corner of the b ack plate and connect to nea[...]

36 Assembling and Maintain ing TRM 800 - Series Treadmills Connectin g th e Heart Rate Sensor Cable The heart rate sensor cable passe s through the cutaway opening at the upper left corner of the back plate, the n down to the small circuit board at the lower left of the cons ole. The following illustration shows how the ca ble should look once it i[...]

Installing the Con sole 37 Completing the Console Installati on (P80) Before you complete the f inal installation steps, doub le - check the connections you have made. Make sure that a ll cables are fully and securely connected, and that any unneeded cab les are tied back properly. To compl ete the instal lation: 1. Feed extra cable back into the n[...]

38 Assembling and Mainta ining TRM 800 - Series Treadmills Threadin g the Cable A sse mbly (P30 a nd P20) Earl ier in the install ation, you threaded the necessary cab les through the frame of the base unit and out the pass through opening in the console mount . As you line up the back plate on the console with the co nsole mount, you must ma ke su[...]

Installing the Con sole 39 Connecting Cables (P30) After the console has been seated, se parate the individua l cables out of the end of th e cable assembly and atta ch them to the appropriate circuit connect ors inside the console. Refer to the following diagram and tab le to identify the cables and connectors. Figure 25 : Cable connections, P30 c[...]

40 Assembling and Mainta ining TRM 800 - Series Treadmills Connecting Cables (P20) After the console has been seated, separate the individual cables out of the end of th e cable assembly a nd attach them to the appropriate circuit connect ors inside the console. Refer to the following diagram and tab le to identify the cables and connectors. Figure[...]

Installing the Con sole 41 Completing the Console Installati on (P30 and P20) Before you complete the f inal installation steps, doub le - check the connections you have made. Make sure that a ll cables are fully and securely connected, and that any unneeded cab les are tied back properly. To compl ete the instal lation: 1. Feed extra cable back in[...]

42 Assembling and Maintaining TRM 800 - Seri es Treadmills Reassembling th e Treadmill Fair ing After the console is in plac e, reattach the two cove r panels of the tread mill fairing. Import ant: In the following procedur e, do not allow the fasteners to break or p inch any c ables. To reasse mble the f airing: 1. V erify that the cable assembly [...]

Installing the Con sole 43 Verifying Th at the Heart Rate Display Is Operational To verify that the hear t rate displ ay is o per ationa l: 1. Begin exercising on the equipment. 2. Grasp both touch - sensitive handlebars. Note: The heart rate is read within ten seconds. D uring that time, the hea rt on the displ ay flashes. 3. Look at the HEART RAT[...]

44 Assembling and Maintain ing TRM 800 - Series Treadmills[...]

Chapter 3 Maintenanc e To keep the equipment f unctioning properly, per form the minor maintenance tasks in t his section at the int ervals shown on the maintenanc e checklist. Failure to main tain the equipment as described in t his section could void the Precor Limited War ranty. DANGER To reduce the risk of electrical shock, a lwa ys disconnect [...]

46 Assembling and Maintain ing TRM 800 - Series Treadmills Alternatively, you can clean the equipment wit h Athletix fitness equipment cleaning wipes (for more information, vi sit www.a thletixprod ucts.com ) CAUTION: Read and follow th e manufacture r ’ s instructions, particular ly dilution instructions, befor e using any cleaner on Precor f i [...]

Maintenance 47 Weekly Mainte nance Perform the following maintenance tasks every week: 1. Elevate the tr ead to maximum incl ine, then tur n off the power switch or circuit breaker and unplug the unit f rom the wall o utlet. 2. Clean the floor under the e quipment using a vacuum cleaner or a damp mop. 3. When the floor is complet ely dry, reconnect[...]

48 Assembling and Maintain ing TRM 800 - Series Treadmills 5. Check the belt tensi on of the step - up and dr ive belts. 6. Clean and lubricate the lif t motor screw with an approv ed grease such as SuperLube® wi th Teflon® or Mobil 1® synthetic grease (adjustable- ram p mod el s o nly ). 7. Check all fasteners for proper tightness and torque. 8[...]

Maintenance 49 If the bel t trac ks off ce nter ... Then loosen ... To the le ft The righ t adj usti ng bol t To the r igh t The le ft a djust ing b olt 3. Recheck the belt position a s described under Checking the Alignment of the Running Belt . Note: If slip page occurs, tighten both adjusting bolts evenly until it stops. Do not o vertighten the [...]

50 Assembling and Mainta ining TRM 800 - Series Treadmills 6. Observe the belt from the rear of the treadmill for a few minutes. The belt should rem ain centered along the running b ed. If it drifts off center, ad just it. Refer to Treadmill : Adjusting t he Running Be lt . Impo rtan t : Failure to align t he belt may cause the belt to tear or fray[...]

Maintenance 51 Long - Term Sto rage If you do not expect anyon e to use the equipment for a long time, perfor m the follow ing tasks to prepar e it for storage:  Turn it O FF.  If it has a power cord, disconnect the cord.  If it has an optional power adapter, connect the adapt er to prevent damage to the inter nal batter y.  Position it[...]

52 Assembling an d Maintaining TRM 800 - Series Treadmills[...]

Chapter 4 T r eadmill Saf ety F eatur es Before allowing users on Precor equipment, review the Important Safety Instruction s in this manual. You should also teach your patrons how to use the equipment safely, according to the guidelines on . Entering the Safety Code When the equipment is shi pped from the factory, safe ty code protection is not ac[...]

54 Assembling and Maintain ing TRM 800 - Series Treadmills Using the Trea dmill Sa fety Clip The treadmill is equipped with two different stop funct ions, which behave as follows: If the us er … Then the trea dmill belt … And the c onsole … Presse s down on the red STOP b utton Slows to a st op Shows t hat the exe rcise worko ut is pa used Pu[...]

Treadmill Safety Fea tures 55 If the restar t switc h trips during exercis e, perform the following steps: 1. Reattach the safety clip if necessary. 2. Press the restart switch do wn until it clicks , returning it to its normal position. Note: If th e restart s witch trips, all in formation ab out the current workout is deleted. 3. Start the workou[...]

56 Assembling and Maintain ing TRM 800 - Series Treadmills[...]

Chapter 5 Commer cial C ar di o v ascula r E quipment Limit ed W arr anty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR PRECOR INCORPORATED PROD UCT. BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND B Y THE FOLLOWING WARRANTY TERMS AND CONDITIONS . Limite d Warr anty. Precor I ncorpor ated w arrants all new P rec[...]

58 Assembling and Maintain ing TRM 800 - Series Treadmills Options / Accessori es Many op tions or a ccess ories h ave c omponents that are conn ected interna lly or mou nted inside the elec tronic co nsole . The f ollowing guide lines d eterm ine the wa rranty f or the se componen ts. If the inte rnal c ompone nts are instal led by the fact ory or[...]

Commercial Cardiovascular Equipment Limited W arran ty 59 This Lim i ted Warran ty sh all not ap ply to: 1. So ftware versi on upgrad es. 2. Softwa re def ects t hat do not ma terially a nd ne gatively aff ect the norm al perf orma nce of the pr oduct und er norm al co nditions of use . 3. Consuma ble goods or cos meti c items of the prod uct, the [...]

60 Assembling and Mainta ining TRM 800 - Series Treadmills EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES. PRECOR AND/OR ITS S UPPLIERS SHALL HAVE NO OBLIGATION OR LIABILI TY, WHETHER ARISING IN CON TRACT (INCLU DING WARRA NTY), TORT (INCLUDING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRICT LIABILI TY), OR OTHERWISE, FOR DAMAGE TO THE EQUIPME[...]

[...]

As sembling and Maintaining TRM 800-Series T r eadmills Prec or Incorporated 20031 142nd A venue NE P .O . Box 7 202 W oodinville, W A USA 98072-400 2 TRM 800-Series P AG/ OM 300713-341 r ev G W arranty #36286- 114 14 F ebruary 2011[...]