Remington QFP40 Bedienungsanleitung

1445 North HIghway Colville, W A 991 14 SA VE THESE INSTRUCTIONS INST ALLA TION, VENTING , OPERA TION AND MAINTENANCE MANUAL FOR YOUR SAFETY DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. REMINGT ON QFP40 Direct V ent Gas Fireplace Part #250-4721 (842-3291) 06/2001 www .aladdinhear[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 2 250-4721 JUNE 2001 Aladdin Hearth Products welcomes you to our tradition of excellence! In choosing a Quadra- Fire appliance, you have our assurance of commitment to quality , durability , and performance. This commitment begins with our research of the market, including ‘V oice of the Customer ’ co[...]

Page 3 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 MODEL NAME Q uadra Fire REMINGTON QFP40 SERIAL NUMBER L ocated on front, lower ledge of control panel. DA TE PURCHASED DEALERSHIP WHERE PURCHASED DEALER PHONE ADDITIONAL INFORMA TION Af ter completing your warranty card, attach your sales receipt and warranty stub here for future refe[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 4 250-4721 JUNE 2001 CONTENTS CONTENTS SAFETY & CLEARANCES: Ratings Plate ................................................................................................. 6 S tandards Listing & Clearances Label .......................................................... 7 Safety Notices ..........[...]

Page 5 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 CONTENTS COMPLETING INST ALLA TION: Gas Line Requirements ................................................................................ 46 Electrical Connection ................................................................................... 47 Optional Thermostat Connection ...[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 6 250-4721 JUNE 2001 1999 2000 2001 JAN FEB MAR MA Y JUN JUL AU G SE P O CT NOV DEC SAFETY LABEL Location: Serial No. portion on lip below control panel. Lower portion behind access door on baseplate to right of control panel. 1445 N. Highway Colville, W A 991 14 LP NG Input Rate on “HI” (BTU/Hr) 40,0[...]

Page 7 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 Install fireplace in accordance with all local codes, if any; if none, follow The National Fuel Gas Codes ANSI Z223.1-1992 and NFP A 54(88); or Canadian Installation Codes CAN/CGA-B149. Manufactured or Mobile Home Installation This appliance is only for use with the type of gas indi- [...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 8 250-4721 JUNE 2001 W ARNING! Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational pro- cedures. For assistance or additional information consult a qualified installer , service agency , or[...]

Page 9 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 SAFETY NOTICES IF YOU SMELL GAS! ☛ Do not light any appliance ☛ Extinguish any open flame ☛ Do not touch any electrical switch or plug or unplug anything ☛ Open windows and vacate building ☛ Call gas supplier from neighbor ’ s house, if not reached, call fire depart- ment [...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 10 250-4721 JUNE 2001 ZC APPL IANCE DIMENSIONS 29 1/16" 41" 45 4" 7" 1" Gas Inlet - 1 1/4" above base of unit, ac cess ible from either side. Electric al Connecti on Nail Down Plat e 37 1/8" 1/2" Stand-of fs (3 per sid e) 32 1/32" 4 1/8" 42" HEA TING [...]

Page 11 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 SPECIFICA TIONS MINIMUM CABINET DIMENSIONS Width 54 9/16" Depth 20 1/2" Height 56 1/2" Minimum 1/2" trim. Maximum mantel depth is 12" The following minimum cabinet dimensions are the minimal allowances for clearance to combustibles, as referenced on page 7 of[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 12 250-4721 JUNE 2001 Access Door Mantel Fascia Framing Simpson-DuraVent V enting ZC Appliance Combustible Wall (See Clearances, Page 7) Gas line Electrical line Horizontal T ermination Cap INST ALLA TION TERMINOLOGY DuraRock, Tile, etc. S tand- offs Glass Header PREP ARA TION[...]

Page 13 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 AN OVERVIEW: INST ALLA TION TO OPERA TION 1. Remove door by releasing four spring clips (2 upper and 2 lower). See Pg. 53. 2. Remove logset, lava rock, embers and packaging materials from firebox. 3. Familiarize yourself with this manual. 4. Finalize your installation decisions and r[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 14 250-4721 JUNE 2001 NOTE: If converting this unit to prop ane, do so at this point of installation. LP CONVERSION INSTRUCTIONS Part # 842-4470 is required for this procedure. CAUTION: DISCONNECT ANY ELECTRICAL CORDS AND TURN OFF GAS SUPPL Y TO UNIT BEFORE PROCEEDING . V alve Regulator T ower 1. T urn co[...]

Page 15 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 Burner Orifice Replacement 5. If logset is installed, remove logs and embers at this time. 6. Use a Phillips screwdriver to remove pilot lighting channel and front log rack. 7. Remove the two Phillips head screws that secure the front and rear burner pans in place. 8. Remove the burn[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 16 250-4721 JUNE 2001 INST ALLA TION MINIMUM FRAMING DIMENSIONS ❖ The 1/2" stand-offs on the back and sides and 4" stand-offs on the top of the fireplace separate the fireplace from the framing members (see page 12, Installation T erminology). These stand-offs may contact the framing mem- bers[...]

Page 17 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 INST ALLA TION CORNER INST ALLA TIONS The usual 45º installation uses the minimum framing dimensions shown in the illustration below . PLEASE NOTE: All clearances as referenced on page 7 still apply . 13 13/ 16" 45 3/16 " 12 1/16 " 43" 10 7/16 " 19 5/8 "[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 18 250-4721 JUNE 2001 INST ALLA TION RAISED FIREPLACE The fireplace and it’s hearth, if desired, may be placed on a platform designed to support the fireplace weight (240lbs.) and venting. Hearth Raised Plat form[...]

Page 19 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 INST ALLA TION Raised Plat form Raised Hearth RAISED FIREPLACE WITH RAISED HEARTH[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 20 250-4721 JUNE 2001 INST ALLA TION HEARTH REQUIREMENTS No clearances to combustible flooring are required for installation of the Remington QFP40, as referenced in the Clearances to Combustibles on page 7 of this manual. NOTE: Ensure the depth of your flooring material does not exceed the 1" height[...]

Page 21 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 INST ALLA TION MANTEL REQUIREMENTS COMBUSTIBLE MANTELS As referenced on page 7, Clearance to Combustible Materials: The allowable height from the top of the glass to the lower edge of a maximum mantel depth of 12", is 30 1/2". The allowable height from the top of the glass [...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 22 250-4721 JUNE 2001 F ASCIA DIMENSIONS ARCHED Part #841-0710 Gold Part #841-0750 Brushed Nickel Part #841-0720 Black 40 1/ 2" R53 7/ 16" 31" 17 1/ 2" 28 7 /8" 32 13 /16" 7 3/ 16" INST ALLA TION ACID WASH ALER T! An acid wash (muriatic acid) is commonly used to remove e[...]

Page 23 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 RECT ANGULAR 40 3/4" 31" 17 1/2" 31 1/2" 7 3/8" INST ALLA TION F ASCIA DIMENSIONS Part #841-0730 Black[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 24 250-4721 JUNE 2001 INST ALLA TION F ACING REQUIREMENTS HEADER NON- COMBUSTIBLE F ACING 3" MIN. FOR ARCHED or RECT ANGULAR F ASCIA Durarock or other non-combustible material must extend from header to floor and to framing on either side. NOTE: Tile may be tucked beneath the fascia on sides and top,[...]

Page 25 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 INST ALLA TION F ACING OVER 1” (25 mm) THICK Facing material greater than 1" (25mm) thick, such as brick, river rock, etc., will require installation around the perimeter of the face. If your unit did not ship with a template for this purpose, contact your dealer for an Arched[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 26 250-4721 JUNE 2001 VENTING GENERAL VENTING INSTRUCTIONS PLEASE NOTE: In order to comply with applicable codes and product warranties, only Simpson Dura-V ent venting components may be used. DO NOT USE FIELD-F ABRICA TED VENTING COMPONENTS. The Quadra-Fire Remington Fireplace QFP40 is approved to be ven[...]

Page 27 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 VENTING SIMPSON DURA-VENT P ARTS LIST Simpson Dura-V ent offers a complete line of component parts for installation in both horizontal and vertical applications. Many items are offered in decorative black, as well as a galvanized finish. The galvanized pipe and fittings are used for [...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 28 250-4721 JUNE 2001 VENTING VENTING INST ALLA TION OPTIONS & GUIDELINES There are four types of direct vent system installations approved for use with the REMINGTON QFP40. It is very important to maintain a balance between the combustion air intake and the flue gas exhaust venting system. The types [...]

Page 29 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 VENTING FIG . 1 HORIZONT AL TERMINA TION TERMINA TION CAP REQUIREMENTS: ON HORIZONT AL TERMINA TIONS USE ONL Y DURA VENT P ART # 985, OR ALADDIN HEARTH PRODUCTS P ART #HHW2 VERTICAL TERMINA TIONS USE ONL Y DURA VENT P ART #991. FIG . 2 VERTICAL TERMINA TION Horizontal T ermination Ca[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 30 250-4721 JUNE 2001 FIG . 3 INST ALLA TION INTO A CLASS A MET AL CHIMNEY (USA ONL Y) VENTING INST ALLA TION, CONT . VENTING Dura V ent #991 ONL Y High Wind T ermination Cap T op Adapter 4" Flex Pipe Retro Connector Direct V ent Pipe Existing Metal Chimney System[...]

Page 31 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 FIG . 4 INST ALLA TION INTO A MASONR Y CHIMNEY (USA ONL Y) DuraV ent #991 High Wind T ermination Cap ONL Y T op Adapter Flashing Direct V ent Pipe Retro Connector 4" Flex Liner VENTING INST ALLA TION, CONT . VENTING[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 32 250-4721 JUNE 2001 VENTING HOW TO USE VENT GRAPH TOT A L HORIZONT A L RUN TO OUTSIDE OF EXTE RIOR W A LL (EX CLUDI NG EL BOWS) 2' 4' 6' 8' 10' 12' 14' 16' 18' 20' 22' 24' 26' 28' 30' 1 1" 2' 4' 6' 8' 10&[...]

Page 33 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 A Ope na ble Fixed Closed B C F G H I A V V V V K A J M N V = vent term inal A = air supply inle t HORIZONT AL TERMINA TION REQUIREMENTS VENTING A. *12” (30cm) minimum: Clearance above grade, veranda, porch, deck, or balcony . B. *12” (30cm) minimum: Clearance to window or door t[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 34 250-4721 JUNE 2001 Step 1. Determine the desired location of the fireplace. Check to ensure that wall studs or roof rafters are not in the way when the venting system is attached. If this is the case, you may want to adjust the location of the stove. Step 2. Simpson Dura-V ent pipe is designed with spe[...]

Page 35 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 Step 3. With the adapter , any vertical pipe required for your installation, and the 90° elbow attached to the flue outlet, measure the distance from the base of the ZC appliance to the center of the 90° elbow , adding 1/4" rise for every 1' of horizontal venting, as refe[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 36 250-4721 JUNE 2001 HORIZONT A L INST ALLA TION (CONT .) Step 4. Position the horizontal vent termination in the center of the 10" (254mm) square hole, run a bead of non-hardening mastic around its outside edges, so as to make a seal between it and the wall, attach termination cap to the exterior w[...]

Page 37 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 Step 5. Slide the stove and vent assembly (see Fig. 9 below) towards the wall, carefully inserting the vent pipe into the vent cap assembly . It is important that the vent pipe extend into the vent cap sufficient distance so as to result in a minimum pipe overlap of 1¼" (32mm).[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 38 250-4721 JUNE 2001 VERTICAL INST ALLA TION INSTRUCTIONS USING GS SERIES PIPE Step 1. Check the installation instructions for required 1" clearances (air space) to com- bustibles when p assing through ceilings, walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces. See page [...]

Page 39 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 1 - 1/ 2" Lon g W oo d S cr ew s C e ili ng J o i sts Fr a m in g Step 4. Assemble the desired lengths of GS pipe and elbows necessary to reach from the stove up through the round support box. Ensure that all pipe and elbow connections are in their fully twist-locked position. B[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 40 250-4721 JUNE 2001 VERTICAL INST ALLA TION INSTRUCTIONS (CONT .) USING GS SERIES PIPE ( CONT .) Step 7. Continue to assemble pipe sections until the height of the vent cap (H) (Figure 15) meets the minimum code requirements described in code requirements as outlined in the current CAN/CGA-Bl49 Installa[...]

Page 41 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 VERTICAL INST ALLA TION INSTRUCTIONS (CONT .) CA THEDRAL CEILING INST ALLA TION Step 1. Follow installation S teps 1 and 2 under vertical termination section. Step 2. Using the plumb-bob, mark the centerline of the venting system on the ceiling, and drill a small hole through the cei[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 42 250-4721 JUNE 2001 VERTICAL INST ALLA TION INSTRUCTIONS (CONT .) INST ALLA TION INTO A CLASS A MET AL CHIMNEY (USA ONL Y) NOTE: Have the existing installation inspected by a qualified chimney sweep or profes- sional installer prior to converting to direct vent. The existing chimney system must be in se[...]

Page 43 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 VERTICAL INST ALLA TION INSTRUCTIONS (CONT .) INST ALLA TION INTO AN EXISTING MASONR Y CHIMNEY (USA ONL Y) Step 1. Before cutting any holes, assemble the desired sections of direct vent pipe to determine the center of the masonry penetration. Step 2. Once the center point of the pene[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 44 250-4721 JUNE 2001 Step 5. Connect the flex liner to the top adapter using three sheet metal screws (see Fig- ure 19, page 42). Step 6. Feed the flex liner through the flashing into the chimney . Carefully feed the flex liner down the chimney to the bottom and out the opening in the masonry wall, formi[...]

Page 45 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 Step 9. Attach the flex to the retro connector . Use three sheet metal screws to attach the flex liner to the connector (Figure 26). Mount the retro connector to the ma- sonry wall using masonry bolts. Redrill larger holes on connector as needed. Be careful to ensure that the connect[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 46 250-4721 JUNE 2001 GAS LINE REQUIREMENTS ✔ The gas line must be installed in accordance with all local codes, if any; if not, follow ANSI 223.1 and the requirements listed below. Ensure that a 1 1/4" allowance from base of unit is made for hard pipe installation, see page 16, Minimum Framing Dim[...]

Page 47 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 ELECTRICAL CONNECTION Make sure the household breaker is shut off prior to working on any electrical lines. This appliance, when installed, must be electrically grounded in acordance with local codes or , in the absence of local codes, with the National Electrical Code, ANSI/NFP A 70[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 48 250-4721 JUNE 2001 . 1. Place rear brick behind log rack against rear wall of firebox as shown in Fig. 1. NOTE: BRICK IS FRAGILE. HANDLE WITH CARE. Inst allation of the brick set should be made prior to the logset, nugget and lava rock inst allation. Optional Accessory Part # 841-0740 Kit s includes: 1[...]

Page 49 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 3. Attach brick retaining clip s to right and left sides, using mounting screws removed in Step 2. (Fig. 4). FIG . 3 FIG . 4 BRICK INST ALL BRICK INST ALLA TION, CONT . Mounting screw & clip placement.[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 50 250-4721 JUNE 2001 1. Install complete bag of lavarock in indicated gray area ONL Y shown in Figs. 1 & 2. LOGSET AND NUGGET INST ALLA TION NOTE: If you plan to inst all the optional brick set, do so prior to inst alling the logset, nugget s and lava rock. Continue at this point AFTER installing the[...]

Page 51 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 LOGSET AND NUGGET INST ALLA TION, CONT . 3. Set Rear Log in rear log bracket with pegs in upright position. Fig. 3. 4. Set the notch in the Front Log over the pilot transfer channel and center log side-to-side on the grate with pegs in upright position. Fig. 4. FIG . 2 NUGGET PLACEME[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 52 250-4721 JUNE 2001 LOGSET AND NUGGET INST ALLA TION, CONT . LOGSET INST ALL 5. Place Left T wig onto pegs on top of Rear and Front Logs. Fig. 5. 6. Place Right T wig onto pegs on top of Rear and Front Logs. Fig. 6. 7. Place Lower Left Front T wig in front of stops on log rack. Fig. 7. 8. Place Lower Fr[...]

Page 53 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 All arched and rectangular fascia attach to four flanges located two to each side of the glass frame. Insert and finger start bolts tightening with the 5/32" Allen wrench supplied with unit. INST ALLING GLASS The glass assembly has a narrow metal edge at top of the frame, and wi[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 54 250-4721 JUNE 2001 LEAK TEST 1. T urn on gas to the fireplace. 2. T urn on gas at the manual shutoff valve. 3. Leak test all gas joints prior to starting the appliance. 4. Familiarize yourself with the control panel components, see page 58. 5. Follow Lighting Instructions on next p age to light the pil[...]

Page 55 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 LIGHTING INSTRUCTIONS LIGHTING FOR YOUR SAFETY READ BEFORE LIGHTING W ARNING: If you do not follow these instructions exactly , a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot that must be lit manually . When ligh[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 56 250-4721 JUNE 2001 ADJUSTMENTS ADJUSTING THE BLOWER SPEED The blower will turn on automatically within approximately 10 minutes after start-up and the fireplace is up to temperature. This aids in transferring the heat into the living area. The blower speed can be increased or decreased using the Fan S [...]

Page 57 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 ADJUSTMENTS HIGH AL TITUDE OPERA TION In Canada, this unit is approved from 0 to 4500 feet above sea level. Installation of this stove at altitudes above 4500 feet is subject to field test of the individual inst allation and approval by the local authority having jurisdiction. In the[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 58 250-4721 JUNE 2001 OPERA TION Read this entire manual prior to using the fireplace. Pay particular attention to the “Safety Precautions” section on pages 6-9. Failure to follow the instructions may result in prop- erty damage, bodily injury , or even death. CONTROL P ANEL F AN SPEED This knob contr[...]

Page 59 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 MAINTENANCE GENERAL Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 60 250-4721 JUNE 2001 YEARL Y SERVICING PROCEDURES W ARNING! Failure to inspect and maintain the fireplace may lead to improper com- bustion and a potentially dangerous situation. The following procedures are rec- ommended to be completed by a qualified technician once per year , preferably prior to the b[...]

Page 61 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 Replace glass with part #842-3820 ONL Y , available from your dealer . 1. T urn valve to “OFF” position to prevent start-up of unit while door is removed. 2. Prep are a flat area to lay the door on by covering the surface with cardboard, disposable tarp or paper large enough to c[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 62 250-4721 JUNE 2001 MAINTENANCE BLOWER REPLACEMENT Part #842-3790 1. Disconnect power to unit at power supply (this may require shutting off power at the circuit breaker box). 2. Remove fascia and door . 3. Remove control panel cover . 4. Disconnect white wire from white wire at junction box in unit. 5.[...]

Page 63 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 MAINTENANCE ELECTRICAL SCHEMA TIC[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 64 250-4721 JUNE 2001 TROUBLESHOOTING Pilot won’t light ✔ Is a gas shut-off valve turned on? ✔ Is the valve control knob turned to “PILOT” (See Lighting Instructions, #7, Pg. 55). ✔ Is the valve control knob pushed in? (See Lighting Instructions, #8) ✔ W as the igniter pressed repeatedly? (S[...]

Page 65 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 TROUBLESHOOTING , (CONT .) Fireplace Design: Many of the components within this fireplace are designed specifically for safety purposes. I t i s therefore imperative that only certified gas service technicians should service this fireplace. Main Burner Operation: A millivolt system c[...]

REMINGTON QFP40 Direct V ent FIREPLACE Page 66 250-4721 JUNE 2001 P ARTS & ACCESSORIES PA R T S 842-0240 V alve (NG) 842-3501 Pilot 842-3910 Pilot Orifice NG (.025) 842-3900 Pilot Orifice LP (.016) 842-4480 Logset (7 pieces) 842-4490 Rear Log 842-4520 Front Log 842-4500 Le ft T wi g 842-4510 Right T wig 842-4530 Lower Left Front T wig 842-4550 [...]

Page 67 REMINGTON QFP40 Direct V ent FIREPLACE 250-4721 JUNE 2001 W ARRANTY GAS APPLIANCE LIMITED LIFETIME WARRANTY Aladdin Hearth Products, warrants this gas heating appliance to the original purchaser for the lifetime of the appliance, to be free from defects in material and workmanship. This warranty gives you specific legal rights; you may have[...]

REMINGT ON QFP40 Direct V ent Gas Fireplace Owner ’ s Manual[...]