Renesas H8S/2628 Bedienungsanleitung

2004.1.29 H8S/2628 Group FP-100B User System Interface Cable HS2628ECH61H User’s Manual Renesas Microcom puter Development Envi ronment System Rev.4.00[...]

Cautions Keep safety firs t in your circuit des igns! 1. Renesas Technology Corp. puts the maximum effort into making s emiconductor products better and more reliable, but there is always the poss ibility that trouble may occur with them. Trouble with se miconductors may lead to pers onal injury, fire or property damage. Remember to give due cons i[...]

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attemp t to use the user system interface cable until you fully understand its mec h an is m. User Syst em Interf ace Ca ble: Throughout th is document, the term "[...]

II LIMITED WARRANTY Renesas warrants its user s ystem interface cables to be manufactured in accordance with published specifications and free from d efects in mater ial and/or workmanship. Renesas will re pair or replace a n y user sy stem interface cables deter mined to be defective in mate rial and/or workmanship. User s ystem interface cables a[...]

III State Law : Some states do not allo w the exclusion or limitatio n of i mpli ed warranties or liabilit y for incidental or consequential da mages, so the above limitatio n or exclusion may not apply to you. Thi s warr an t y give s yo u spec i fic le gal ri ght s, and you ma y ha ve ot her rig hts wh ic h ma y var y fro m state to state. The Wa[...]

IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attemp t to use the user system interface cable until you fully understand its mec h an is m. DEFINITION OF SI GNAL WORDS This is the safety alert sy mbol. It is u sed to al ert[...]

V W ARNING Observe the pr ecautions listed b elow. Failure to do so will result in a FIRE H AZARD and will damage the user system and the emul ator product or will r esult in PERSONAL INJURY. The USER PROGRA M will be LOST. 1. Do not repair or remodel the emul ator product by yourself for elect ric shock pre vention and quality assur ance. 2. Alway[...]

i Preface Thank y ou for purch asing this us er sys tem in terface cable (HS2628ECH61H) f or the Renes as’ origin al m icrocom puter H8S/ 2628 group. The HS2628ECH61H is a u ser sy stem interface cable th at connects an H8S/2628 group E6000 emu lator (HS 2628EPI61H; herein after ref erred to as the em ul ator) to the IC socket for an FP-100B pack[...]

ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User Sy stem In terface Cable to Em ulator Station .......................................... 3 2.2 Connect[...]

1 Section 1 Configuration CAUTION Use an IC149-100- 054-B51 socket (manuf actured by YAMAICH I ELECTRONICS Co., Lt d.) for the FP- 100B package IC socket on the user syst em. Figure 1 s how s the conf iguration of the HS2628ECH 61H user sy stem interface cable f or the FP-100B packag e. User system IC socket Cable head Screws (M2.6 x 12 mm) with fl[...]

2 Table 1 li s ts t h e HS 2628EC H61H com ponen t s. Pl eas e m ake su re you h ave all of t h es e com ponen ts when unpacking. Table 1 HS2628ECH61H Com p onents No. Component Quantity Remar ks 1 Cable body 1 Cable 2 Cable head 1 3 IC socket 1 For the FP-100B package 4 Socket cover 1 For installing an FP-100B packaged M CU 5 Screws (M 2.6 x 12 mm[...]

3 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user syst em[...]

4 Emulator station E6000 Cable body connector User system interface cable Figure 2 Connecting User System Interface Cable to Em ulator Station[...]

5 2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part . Before connecting, make sure that pin 1 on bot h sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage[...]

6 2.2.3 I nsertin g Cable Head CAUTION Check the location of pin 1 before inserting. Alig n pin 1 on the IC socket for an FP- 100B package on the us er syst em w ith pin 1 on the user sy stem interface cable h ead, and insert the u ser sy stem interface cable head in to the IC socket on the user system, as shown in figure 3. 2.2.4 Fas tening Cab le[...]

7 Fasten th e user sy stem interf ace cable head to the IC sock et for an FP-100B pack age on the u ser system w ith the four scr ews (M2.6 x 12 m m; wi th fou r flat w ash ers) provided. Each screw sh ould be tighten ed a little at a tim e, alternating betw een s crew s on opposin g corn ers . Take special care, such as m anually securing the IC s[...]

8 2.2.5 Fas tening Cab le Body Connect the cable body to the cable h ead. Cable body Cable head Remove jig Push two remove jigs. Removing User system Figure 4 Fastening Cable Body[...]

9 2.3 Recomm ended Dimensions for User System Mount Pad Figure 5 sh ow s th e recom m en ded dim ension s f or th e m ount pad (footprint) for the user sys tem with an IC s ocket for an FP-100B packag e (IC149-100- 054-B51: m anuf actured by YA MAICHI ELECTRONICS C o., Ltd.). Note th at the dim ens ions in figu re 5 are somew h at differen t from t[...]

10 2.4 Dimensions for User System Interface Cable Head The dimen sions for th e user sy stem interface cable h ead are show n in f igure 6. Unit: mm Tolerance: ±0.5 mm 63.5 63.5 17.0 17.0 29.5 29.5 Figure 6 Dim ensions for User System Interface Cable Head[...]

11 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dim ens ions, after con necting th e user sy stem interface cable head to th e user sy stem , are show n in figu re 7. 16.0 21.5 Cable head User system Unit: mm Tolerance: ±0.5 mm IC socket (IC149-100-054-B51 manufactured by YAMAICHI ELECTRONICS Co. Ltd.) Figure[...]

12 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.0785 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the f orce required to turn th e screw becom[...]

13 MCU Pin 1 IC socket (IC149-100-054-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Screws (M2.6 x 6 mm) with flat washers Socket cover Figure 8 Installing M CU to User System[...]

14 Section 4 Verifying Oper ation 1. Turn on the emu lator according to th e procedures described in the H8S Fam ily E6000 Em ul ator User' s Manu al (HS2000EPI61HE). 2. Verify the user sy stem in terface cable connections by accessing the external m emory and ports to check the bu s st ates of th e pins w ith th e MEMORY_FIL L com m an d (emu[...]

15 Section 5 Notice 1. Make s ure that pin 1 on the user sy stem IC socket is correctly aligned w ith pin 1 on the cable head before insertin g the cable head in to the user sy stem IC socket. 2. The dimen s ion s of the recom m ended m oun t pad f or th e u s er sy stem IC s ocket are dif ferent f rom those of the MCU. 3. This user sy stem interf [...]

H8S/2628 Group FP-100B User System Interface Cable HS2628ECH61H User's Manual Publication Date: Rev.4.00, January 29, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd.  2004 Renesas Technology Corp. All rights rese[...]

H8S/26 28 Gr oup F P-100B User Sy stem Inte rface C able HS2628E C H61H U ser’ s Manual REJ10B0084-0400H[...]