Samsung RNX-EASYN4 Bedienungsanleitung

Wireless Router RNX-EasyN4 User Manual[...]

T ABLE OF C ONTENTS 1 INTRODUCTION .............................................................................................................. 3 2 KEY FEA TURES .............................................................................................................. 4 3 P ACKAGE CONTENTS .....................................................[...]

Introduction Congratulations on your purchase of RNX-EASYN4 Wireless Network Broadband Router. RNX-EASYN4 is compliant with draft 802.11n v2.0 up to 6 times faster than standard 802.11g based routers while st ill being compatible with 802.11g & 802.11b gadgets. RNX-EASYN4 is not only a Wirele ss Access Point, but also doubles as a 4-port full-d[...]

Wireless Router RNX-EasyN4 U ser Manual 1 Key Features Features Advantages Incredible Data Rate up to 300Mbps** Heavy data payloads such as MPEG video streaming IEEE 802.11n Compliant and backward compatible with 802.11b/g Fully Interoperable with IEEE 802.11b / IEEE 802.11g compliant devices with legacy protection Four 10/100 Mbps Fast Switch Port[...]

Wireless Router RNX-EasyN4 U ser Manual 2 Package Contents Open the package carefully , and make sure that none of the items listed below are missing. Do not discard the packin g materials, in case of return; the unit must be shipped back in its origin al package. 1. 802.11n SOHO Router 2. 100V~120V Power Adapter 3. 2dBi 2.4GHz Fixed Antennas 4. Qu[...]

Wireless Router RNX-EasyN4 U ser Manual 3 Product Layout[...]

Wireless Router RNX-EasyN4 U ser Manual LED Description POWER Lights up when powered ON. Blinks on TEST/RESET WLAN Lights up in ORANGE when WLAN is enabled. Blinks on traffi c LAN PORT ACTIVY Blinks on traffic for specific LAN PORT 100 Mbps Lights up when 100 Mbp s data rate enabled on that specific port ITEM Description Reset Click this button to [...]

Wireless Router RNX-EasyN4 U ser Manual WPS Click this button to start WPS function. DC IN Power connector , connects to DC 12V Power Adapter LAN1 ~ 4 Local Area Network (LAN) port s 1 to 4 INTERNET Wide Area Network(W AN) port[...]

Wireless Router RNX-EasyN4 U ser Manual 4 Network + System Requirements T o begin using the RNX-EASYN4, make sure you meet the following as minimu m requirements: h PC/Notebook. h Operating System – Microsoft Windows 98SE/ME/XP/2000/VIST A h 1 Free Ethernet port. h WiFi card/USB dongle (802.1 1b/g/n) – optional. h External xDSL (ADSL) or Cable [...]

Wireless Router RNX-EasyN4 U ser Manual 6 Setup LAN, WAN LAN connection: Connect Ethernet cable between your PC/Notebook LAN port & one of the 4 available LAN ports on RNX -EASYN4. W AN connection: Connect Ethernet cable between W AN ports of your ADSL/CABLE modem & INTERNET port of RNX-EASYN4. Make sure your ADSL/CABLE modem is working wel[...]

Wireless Router RNX-EasyN4 U ser Manual 7 PC Network Adapter setup ( Windows XP ) • Enter [Start Menu] Æ select [Control panel] Æ select [Network]. • Select [Local Area Connection]) icon=>select [properties][...]

Wireless Router RNX-EasyN4 U ser Manual • Select [Internet Protocol (TCP/IP)] =>Click [Properties]. • Select the [General] tab. RNX-EASYN4 supports [DHCP] function, please select both [Obtain an IP address automatically] and [Obtain DNS server address automatically].[...]

Wireless Router RNX-EasyN4 U ser Manual 8 Bring up RNX-EASYN4 Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. Then, RNX-EASYN4 autom atically enters the self-test phase. During self-test phase, Power LED wi ll blink briefly, and then will be lit continuously to indicate that th is product is in normal ope[...]

Wireless Router RNX-EasyN4 U ser Manual Click Setup Wizard to setup your RNX-EASYN4 router. Click User Manual to launch smart wizard user manual. Click Adobe Reader to setup Adobe Acrobat reader on your PC/Notebook. Click EXIT anytime you want to abort.[...]

Wireless Router RNX-EasyN4 U ser Manual Click <Next> to proceed. Click <Exit> to abort.[...]

Wireless Router RNX-EasyN4 U ser Manual RNX-EASYN4 should be setup as depicted above. Make sure your DSL/CABLE modem is setup and working. Else take the help of your internet service provider. Click <Next> to proceed.[...]

Wireless Router RNX-EasyN4 U ser Manual Check the MODEM and RNX-EASYN4 connection. It should be as shown below. Check power connection for modem as well as RNX-EASYN4. Make sure antenna is connected to rear panel of RNX -EASYN4. Click <Next> to proceed.[...]

Wireless Router RNX-EasyN4 U ser Manual Notice the LED that should be light up at this stage. If not, check your procedures again. Click <Next> to configure WAN & Wireless settings.[...]

Wireless Router RNX-EasyN4 U ser Manual User name and password are admin/admin. Click <OK> . Your default browser will connect to RNX-EASYN4 Web Server http://192.168.0.1 .[...]

Wireless Router RNX-EasyN4 U ser Manual Click <Next> to enter mode selection. Select the mode that RNX-EASYN4 is going to be and set its configurations. AP Router mode does not enable WAN interface, Setup Wizard will skip WAN Configuration.[...]

Wireless Router RNX-EasyN4 U ser Manual Click <Next> to automatically detect your Internet Network settings. You could choose your service type or sele ct Others to setup WAN configurations manually. Smart Wizard has detected DHCP client. Configure the host name and MAC address of your ADSL modem. Click Next to proceed.[...]

Wireless Router RNX-EasyN4 U ser Manual Smart Wizard has finished setting up WAN Configuration . Click <Next> to proceed. Enter the name for your wireless network (SSID) and security key Click <Next> to proceed[...]

Wireless Router RNX-EasyN4 U ser Manual To apply the entire configuration, click <Reboot> . NOTE: After Wireless settings are applied, you need to connect from your WLAN client with the security settings you just finished configuring. Remember the type of security & security key .[...]

Wireless Router RNX-EasyN4 U ser Manual 10 Initial Setup RNX-EASYN4 RNX-EASYN4 uses web-interface for configuration to be a ccessed through your web browser, such as Internet Explorer or Netscape Communicator. - LOGIN Procedure 1. OPEN your browser (e.g. Internet Explorer). 2. Type http://192.168.0.1 in address bar and hit [Enter] button on your ke[...]

Wireless Router RNX-EasyN4 U ser Manual 3. Click <OK> to navigate into RNX-EASYN4 configuration home page. 4. You will see the home page of RNX-EASYN4 as follows.[...]

Wireless Router RNX-EasyN4 U ser Manual 12 AP Router Mode  System - S tatus This page allows you to monitor the current status of your router. You can use the status page to quickly see if you have any updated firmware available (bug fixes, updates). You can navigate from this page with a few interesting options for reminding or skipping this pa[...]

Wireless Router RNX-EasyN4 U ser Manual WAN Settings: This section displays whether the WAN port is connected to a Cable/DSL connection. It also displays the router’s WAN IP address, Subnet Mask, and ISP Gateway as well as MAC address, the Primary DNS. LAN Settings: This section displays the Broadband router LAN port’s current LAN & WLAN in[...]

Wireless Router RNX-EasyN4 U ser Manual WLAN Settings: This section displays the current WLAN configuratio n settings you’ve configured in the Wizard / Basic Settings / Wireless Settings section. Wireless configur ation details such as SSID, Security settings, BSSID, Channel number, mode of operation are briefly shown.[...]

Wireless Router RNX-EasyN4 U ser Manual - LAN The LAN Tabs reveals LAN settings which can be altered at will. If you are an entry level user, try accessing a website from your browser. If you can access website without a glitch, just do not change any of these settings. Click <Apply> at the bottom of this screen to save the changed configur a[...]

Wireless Router RNX-EasyN4 U ser Manual LAN IP IP address: 192.168.0.1. It is the router’s LAN IP address (Your LAN clients default gateway IP address). It can be changed based on your own choice. IP Subnet Mask: 255.255.255.0 Specify a Subnet Mask for your LAN segment. 802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree fu[...]

Wireless Router RNX-EasyN4 U ser Manual Start IP: This will be the beginning of the pool of IP add resses available for client devices. End IP: This will be the end of the pool of IP addresses ava ilable for client devices. Domain name: The Domain Name for the existing or customized network. - DHCP View the current LAN clients which are assigned wi[...]

Wireless Router RNX-EasyN4 U ser Manual - Schedule This page allows user to set up schedule function for Firewall and Power Saving .[...]

Wireless Router RNX-EasyN4 U ser Manual Add schedule, edit schedule options to a llow configuration of firewall and power savings services. Fill in the schedule and select type of service. Click < Apply > to implement those settings.[...]

Wireless Router RNX-EasyN4 U ser Manual The schedule table lists the pre-schedule service-runs. You can select any of them using the check box. - Event Log View operation event log . This page shows the current system log of the Broadband router. It displays any event occurred after system start up. At the bottom of the page, the system log can be [...]

Wireless Router RNX-EasyN4 U ser Manual - Monitor Show histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequently.[...]

Wireless Router RNX-EasyN4 U ser Manual - Language This Wireless Router support multiple language of web pages, You could select your native language here.[...]

Wireless Router RNX-EasyN4 U ser Manual  Wizard Click Wizard to configure the Broadband Router. Setup wizard will now b e displayed; check that the modem is connected and click <Next>. The details please refer to Smart Wizard.[...]

Wireless Router RNX-EasyN4 U ser Manual  INTERNET - S tatus This page shows the current Internet connection type and status - Dynamic IP Use the MAC address when registering for Internet service, and do not change it unless required by your ISP . If your ISP used the MAC address of the Ethernet card as an identifier , connect only the PC with th[...]

Wireless Router RNX-EasyN4 U ser Manual Host Name: This is optional. MAC address: The default value is set to the WAN’ s physical interface of the broadband router . - S tatic IP If your ISP Provider has assigned a fixed IP a ddress, enter the assigned IP address, Subnet mask, Default Gateway IP address, and Primary DNS of your ISP provider .[...]

Wireless Router RNX-EasyN4 U ser Manual - Point-to-Point over Ethernet Protocol (PPPoE)[...]

Wireless Router RNX-EasyN4 U ser Manual Login / Password: Enter the PPPoE username and password assigned by your ISP Provider . Service Name: This is normally optional. Maximum T ransmission Unit (MTU): This is the maxi mum size of the p ackets. T ype: Enable the Auto-reconnect option to automatically re-est ablish the connection when an applicatio[...]

Wireless Router RNX-EasyN4 U ser Manual  Wireless Settings - Basic In basic setting page, you can set wireless Radio, Mode, Band, SSID, and Channel. Radio: You can turn on/off wireless radio. If wireless Ra dio is off, you cannot associate with AP through wireless. Mode: In this device, we support three operation modes which are AP router and AP[...]

Wireless Router RNX-EasyN4 U ser Manual 2.4 GHz(B): If all your clients are 802.11b, select this one. 2.4 GHz(N): If all your clients are 802.11n, select this one. 2.4 GHz(B+G): Either an 802.11b or an 802.11g wireless devices are in your environment. 2.4 GHz(G): If all your clients are 802.11g, select this one. 2.4 GHz(B+G+N): Either 802.11b, 802.[...]

Wireless Router RNX-EasyN4 U ser Manual - WDS with AP Router Wireless Distribution System , a system that enables the wireless interconnection of access point, allows a wireless network to be expended using multiple access points without a wired backbone to like them. Each WDS APs need setting as same channel and encryption type. MAC address 1~4: P[...]

Wireless Router RNX-EasyN4 U ser Manual - Advanced This tab allows you to set the advanced wireless options. The options included are Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, and Preamble Type. You should not change these parameters unless you know what effect the changes will have on the router. Fragment Threshold: [...]

Wireless Router RNX-EasyN4 U ser Manual Beacon Interval: is the interval of time that this wireless router br oadcasts a beacon. A Beacon is used to synchronize the wireless network. DTIM Period: Enter a value between 1 and 255 for the Delivery Traffic Indication Message (DTIM). A DTIM is a countdown informing clients of the next window for listeni[...]

Wireless Router RNX-EasyN4 U ser Manual - Security This Access Point provides complete wireless LAN security function s, included are WEP, IEEE 802.1x, IEEE 802.1x with WEP, WPA with pre-shared key and WPA with RADIUS. With these security functions, you can prevent your wireless LAN from illegal access. Please make sure your wireless stations use t[...]

Wireless Router RNX-EasyN4 U ser Manual WMM: Wi-Fi MultiMedia if enabled supports QoS for experiencing better audio, video and voice in applications. Encryption: When you choose to disable encryption, it is very insecure to operate RNX-EASYN4. Enable 802.1x Authentication IEEE 802.1x is an authentication protocol. Every user must use a valid accoun[...]

Wireless Router RNX-EasyN4 U ser Manual Authentication Type: There are two authentication types: "Open System" and "Shared Key" . When you select "Open Sy stem" , wireless stations can associate with this wireless router without WEP encryption. When you select "Shared Key" , you should also setup a WEP key in[...]

Wireless Router RNX-EasyN4 U ser Manual 64-bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range) or 5-digit ASCII character as the encryption keys. 128-bit WEP: input 26-digit Hex values (in the "A-F", "a-f" and "0-9" range) or 13-digit ASCII characters as the encryptio[...]

Wireless Router RNX-EasyN4 U ser Manual WP A-Radius Encryption Wi-Fi Protected Access ( WPA ) is an advanced security standard. You can use an external RADIUS server to authenticate wireless stations and provide the sessio n key to encrypt data during communication. It uses TKIP o r C C M P ( AES ) to change the encryption key freque ntly. Press &l[...]

Wireless Router RNX-EasyN4 U ser Manual - MAC Address Filtering This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network. Enable wireless access control: Enable the wireless access control function[...]

Wireless Router RNX-EasyN4 U ser Manual Adding an address into the list Enter the "MAC Address" and "Comment" of t he wireless station to be added and then click <Add> . The wireless station will now be added into the "Current Access Control List" below. If you are having any difficulties filling in th e fields, [...]

Wireless Router RNX-EasyN4 U ser Manual WPS: Check the box to enable WPS function and uncheck it to disable the WPS function. WPS Current Status: If the wireless security (encryption) function of this wireless router is properly set, you’ll see a ‘Configured’ message here. Otherwise, you’ll see ‘ UnConfigured’ . Self Pin Code: This is t[...]

Wireless Router RNX-EasyN4 U ser Manual Authentication Mode: It shows the active authentication mode for the wireless connection. Passphrase Key: It shows the passphrase key that is randomly generated by the wireless router during the WPS process. You may need this information when using a device which doesn’t support WPS. Interface: If device is[...]

Wireless Router RNX-EasyN4 U ser Manual - Policy The Broadband router can allow you to set up the Wireless Access Policy. WAN Connection: Allow Wireless Client on specific SSID to access WAN port. Communication between Wireless clients: Allow Wireless Client to com municate with other Wireless Client on specific SSID. Communication between Wireless[...]

Wireless Router RNX-EasyN4 U ser Manual  Firewall Settings The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attacks, and def ending against a wide array of common Internet attacks. However, for applic ations that require unrestri c ted access to the Internet, you c[...]

Wireless Router RNX-EasyN4 U ser Manual Note : To enable the Firewall settings select Enable and click Apply - Advanced You can allow the VPN packets to pass through this Broadband router.[...]

Wireless Router RNX-EasyN4 U ser Manual - Demilit arized Zone (DMZ) If you have a client PC that cannot run an Internet ap plication (e.g. Games) properly from behind the NAT firewall, then you can open up the firewall restrictions to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets g[...]

Wireless Router RNX-EasyN4 U ser Manual Enable DMZ: Enable/disable DMZ LAN IP Address: Fill-in the IP address of a particular host in your LAN Network that will receive all the packets originally going to the WAN port/Public IP address above. Click <Apply> at the bottom of the screen to save the above configurations. - Denial of Service (DoS)[...]

Wireless Router RNX-EasyN4 U ser Manual Ping of Death: Protections from Ping of Death attack. Discard Ping From WAN: The router’s WAN port will not respond to any Ping requests Port Scan: Protects the router from Port Scans. Sync Flood: Protects the router from Sync Flood attack. - MAC Filter[...]

Wireless Router RNX-EasyN4 U ser Manual If you want to restrict users from accessing certain Internet applications / services (e.g. Internet websites, email, FTP etc.), and then this is the place to set that configuration. Access Control allows users to define the tra ffic type permitted in your LAN. You can control which PC client can have access [...]

Wireless Router RNX-EasyN4 U ser Manual Add PC MAC Address Fill in “ LAN MAC Address ” and <Description> of the PC that is allowed to access the Internet, and then click <Add> . If you find any typ o before adding it and want to retype again, just click <Reset> and the fields will be cleared. Remove PC MAC Address If you want [...]

Wireless Router RNX-EasyN4 U ser Manual - IP Filter Enable IP Filtering: Check to enable or disable IP Filtering. Deny: If you select “ Deny ” then all clients will be allowed to access Internet accept for the clients in the list below. Allow: If you select “ Allow ” then all clients will be denied to access Internet accept for the PCs in t[...]

Wireless Router RNX-EasyN4 U ser Manual Click <Apply> at the bottom of the screen to save the above configurations. - URL Filter You can block access to some Web sites from particular PCs by entering a full URL address or just keywords of the Web site. Enable URL Blocking: Enable or disable URL Blocking Add URL Keyword Fill in “URL/Keyword?[...]

Wireless Router RNX-EasyN4 U ser Manual Remove URL Keyword If you want to remove some URL keywords from the " Current URL Blocking Table ", select the URL keyword you want to remove in the table and then click <Delete Selected> . If you want remove all URL keywords from the table, click <Delete All> button. If you want to clea[...]

Wireless Router RNX-EasyN4 U ser Manual  Advanced Settings - Network Address T ranslation (NA T) Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public I P Addresses. NAT provides Firewall protection from hacker attacks and has the flexibility to all[...]

Wireless Router RNX-EasyN4 U ser Manual - Port Mapping Port Mapping allows you to re-direct a particular range of service port numbers (from the Internet / WAN Port) to a particular LAN IP address. It helps you to host servers behind the router NAT firewall. Enable Port Mapping: Enable or disable port mapping function. Description: description of t[...]

Wireless Router RNX-EasyN4 U ser Manual Add Port Mapping Fill in the " Local IP ", “ Type ”, “ Port Range ” and " Description " of the setting to be added and then click " Add ". Then this Port Mapping setting will be added into the " Current Port Mapping Table " below. If you find any typo before add[...]

Wireless Router RNX-EasyN4 U ser Manual[...]

Wireless Router RNX-EasyN4 U ser Manual Enable Port Forwarding: Enable or disable Port Forwarding. Description: The description of this setting. Local IP / Local Port: This is the LAN Client/Host IP address and Port number that the Public Port number packet will be sent to. Type: Select the port number protocol type (TCP, UDP or both). If you are u[...]

Wireless Router RNX-EasyN4 U ser Manual - Port T riggering (Special Applications) Some applications require multiple connections, such as Internet games, video Conferencing, Internet telephony and others. In this section you can configure the router to support multiple connections for these types of applications. Enable Trigger Port: Enable or disa[...]

Wireless Router RNX-EasyN4 U ser Manual Popular Applications: This section list s the more popular applications that require multiple connections. Select an application from the Popular Applications selection. Once you have selected an application, select a location (1-5) in the Copy to selection box and then click the Copy to button. This will aut[...]

Wireless Router RNX-EasyN4 U ser Manual - Application Layer Gateway (ALG) You can select applications that need ALG support. The router will let the selected application to correctly pass through the NAT gateway. - UPNP With UPnP, all PCs in you Intranet will di scover this router automatically. So, you don’t have to configure your PC and it can [...]

Wireless Router RNX-EasyN4 U ser Manual Enable/Disable UPnP: You can enable or Disable the UPnP feature here. After you enable the UPnP feature, all client systems that support UPnP, like Windows XP, can discover this router automatically and access the Internet through this router without having to configure anything. The NAT Traversal function pr[...]

Wireless Router RNX-EasyN4 U ser Manual get enough bandwidth. This can let you have a better experience in using critical real time services like Internet phone, video confere nce …etc. All the applications not specified by you are classified as rule “Others”. The rule with a smaller priority number has a higher priority; the rule with a larg[...]

Wireless Router RNX-EasyN4 U ser Manual Unlimited Priority Queue: The LAN IP address will not be bounded in the QoS limitation. High/Low Priority Queue: This can put the p ackets in the protocol and port range to High/Low QoS Queue. Bandwidth Allocation: This can reserve / limit the throughput of specific protoco ls and port range. Y ou can set the[...]

Wireless Router RNX-EasyN4 U ser Manual T ype: S pecify the direction of packet s. Upload, download or both. IP range: S pecify the IP address range. Y ou could also fill one IP address Protocol: S pecify the p acket type. The default ALL will put all p ackets in the QoS priority Queue. Port range: S pecify the Port range. Y ou could also fill one [...]

Wireless Router RNX-EasyN4 U ser Manual Destination LAN IP: S pecify the destination LAN IP address of static routing rule. Subnet Mask: S pecify the Subnet Mask of static routing rule. Default Gateway: S pecify the default gateway of static routin g rule. Hop s: S pecify the Ma x Hops number of st atic routing rule. Interface: S pecify the Interfa[...]

Wireless Router RNX-EasyN4 U ser Manual Old Password: Fill in the current password to allow changi ng to a new password. New P asswor d: Enter your new password and type it again in Repeat New Password for verification purposes Remote managemen t This allows you to designate a host in the Internet the ability to conf igure the Broadband router from[...]

Wireless Router RNX-EasyN4 U ser Manual Host Address: This is the IP address of the host in the Internet that will have management/configuration access to the Broadband router from a remote site. If the Host Address is left 0.0.0.0 this means anyone can access the router’s web-based configuration from a remote location, providing they know the pa[...]

Wireless Router RNX-EasyN4 U ser Manual Synchronize with the NTP server Time Zone: Select the time zone of the country you are currently in. The router will set its time based on your selection. NTP Time Server: The router can set up external NTP Time Server. Daylight Savings: The router can also take Daylight Savings into account. If you wish to u[...]

Wireless Router RNX-EasyN4 U ser Manual PC Date and Time: This field would display the PC date and time. Daylight Savings: The router can also take Daylight Savings into account. If you wish to use this function, you must sele ct the Daylight Savings Time period and check/tick the enable box to enable your daylight saving configuration. Click <A[...]

Wireless Router RNX-EasyN4 U ser Manual providers. This router supports DynDNS, TZO and other common DDNS service providers. Enable/Disable DDNS: Enable or disable the DDNS function of this router Server Address: Select a DDNS service provider Host Name: Fill in your static domain name that uses DDNS. Username: The account that your DDNS service pr[...]

Wireless Router RNX-EasyN4 U ser Manual Saving power in WLAN mode can be enabled / disabled in this page. - Diagnosis This page could let you diagnosis your current network status.[...]

Wireless Router RNX-EasyN4 U ser Manual - Firmware This page allows you to upgrade the router’s firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the a ppropriate field on this page. You can also use the Browse button to find the firmwar[...]

Wireless Router RNX-EasyN4 U ser Manual Once you’ve selected the new firmware file, click < Apply > at the bottom of the screen to start the upgrade process - Back-up This page allows you to save the current router configurations. When you save the configurations, you also can re-load the saved configurations into the ro uter through the Re[...]

Wireless Router RNX-EasyN4 U ser Manual Backup Settings: This can save the Broadband router current configuration to a file named " config.bin " on your PC. You can also use the <Upload> button to restore the saved configuration to the Broadband router. Alternatively, you can use the " Restore to Factory Defaults " tool to[...]

Wireless Router RNX-EasyN4 U ser Manual[...]

Wireless Router RNX-EasyN4 U ser Manual 13 Repeater Mode Repeater mode has limited settings compared to the AP mode. Choose “Repeater mode” on the top right corner of the configuration page. System restarts and connects to the IP address http://192.168..0.1 You will see the configuration homepage under “ REPEATER ” mode now.  System - St[...]

Wireless Router RNX-EasyN4 U ser Manual You can see the UP time, hardware information, serial number as well as firmware version information. LAN Settings: This page displays the Broadband router LAN port’s current LAN & WLAN information. It also shows whether the DHCP Server function is enabled / disabled. Wireless configuration details su c[...]

Wireless Router RNX-EasyN4 U ser Manual IP address: It is the router’s LAN IP address (Your LAN clients default gateway IP address). It can be changed based on your own choice. IP Subnet Mask: Specify a Subnet Mask for your LAN segment. 802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree function is enabled, this router wil[...]

Wireless Router RNX-EasyN4 U ser Manual The schedule table lists the pre-schedule service-runs. You can select any of them using the check box.[...]

Wireless Router RNX-EasyN4 U ser Manual - Event Log View operation log of RNX-EASYN4 . This page shows the current system log of the Broadband router. It displays any event occurred after system sta rt up. At the bottom of the page, the system log can be saved <Save> to a local file for further processing or the system log can be cleared <[...]

Wireless Router RNX-EasyN4 U ser Manual - Monitor Show the network packets histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequently. - Language This Wireless Router support multiple language of web pages, you could select your native language here.[...]

Wireless Router RNX-EasyN4 U ser Manual  Wireless -Basic You can set parameters that are used for the wireless stations to connect to this router. The parameters include Mode, ESSID, C hannel Number and Associated Client.[...]

Wireless Router RNX-EasyN4 U ser Manual Radio: Enable or Disable Wireless function Band: Allows you to set the AP fixed at 802.11b, 802.11 g or 802.11n mode. You can also select B+G mode to allow 802.11b and 802.11g clients at the same time. Enable ESSID: You can specify the maximum ESSID number. ESSID1~3: Allow you to specify ESSID of WLAN. Site S[...]

Wireless Router RNX-EasyN4 U ser Manual -Clint List This WLAN Client Table shows the Wireless client associate to this Wireless Router.[...]

Wireless Router RNX-EasyN4 U ser Manual -Policy The Broadband router can allow you to set up the Wireless Access Policy. Communication between Wireless clients: Allow Wireless Client to communicate with other Wireless Client on specific SSID. Communication between Wireless clients and wired clients: Allow Wireless Client to communicate with other W[...]

Wireless Router RNX-EasyN4 U ser Manual  Tools - Admin You can change the password required to log into the broadband router's system web-based management. By default, the passwor d is: admin. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive. Old Password: Fill in the current password to allow changi ng to a new[...]

Wireless Router RNX-EasyN4 U ser Manual New P asswor d: Enter your new password and in Repeat New Password for verification purposes Click <Apply> at the bottom of the screen to save the above configurations Remote managemen t This allows you to designate a host in the Internet the ability to configure the Broadband router from a remote site.[...]

Wireless Router RNX-EasyN4 U ser Manual - T ime The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions such as Event Log entries and Schedule settings. Time Setup: Synchronize with the NTP server[...]

Wireless Router RNX-EasyN4 U ser Manual Time Zone: Select the time zone of the country you are currently in. The router will set its time based on your selection. NTP Time Server: This accept local the IP Address of Local NTP Time Serve r Address. Daylight Savings: The router can also take Daylight Savings into account. If you wish to use this func[...]

Wireless Router RNX-EasyN4 U ser Manual Daylight Savings: The router can also take Daylight Savings into account. If you wish to use this function, you must select the Daylight Savings Time period and check/tick the enable box to enable your daylight saving configuration. Click <Apply> at the bottom of the screen to save the above configurati[...]

Wireless Router RNX-EasyN4 U ser Manual - Diagnosis This page could let you diagnosis your current network status. - Firmware This page allows you to upgrade the router’s firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate [...]

Wireless Router RNX-EasyN4 U ser Manual Once you’ve selected the new firmware file, click < Apply > at the bottom of the screen to start the upgrade process[...]

Wireless Router RNX-EasyN4 U ser Manual - Back-up The page allows you to save (Backup) the router’s current configuratio n settings. When you save the configuration setting (Backup) you can re-load the saved configuration into the router through the Restore selection . If extreme problems occur you can use the Restore to Factory Defaults selectio[...]

Wireless Router RNX-EasyN4 U ser Manual - Reset You can reset the broadband router when system stops responding correctly or stop functions.[...]

Wireless Router RNX-EasyN4 U ser Manual Appendix A – FCC Interference Statement Federal Communication Commission Interference St atement This equipment has been te sted and found to comply with the limits for a Class B digital device , pursuant to Part 15 of the FCC Ru les. These limits are designed to provide reasonable protection against harmfu[...]

Wireless Router RNX-EasyN4 U ser Manual Appendix B – IC Interference Statement Industry Canada st atement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not ca use harmful interference, and (2) this device must accept any interference received, including i[...]