Samsung SCC-B2015P Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Samsung SCC-B2015P an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Samsung SCC-B2015P, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Samsung SCC-B2015P die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Samsung SCC-B2015P. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Samsung SCC-B2015P sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Samsung SCC-B2015P
- Den Namen des Produzenten und das Produktionsjahr des Geräts Samsung SCC-B2015P
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Samsung SCC-B2015P
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Samsung SCC-B2015P zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Samsung SCC-B2015P und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Samsung finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Samsung SCC-B2015P zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Samsung SCC-B2015P, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Samsung SCC-B2015P widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    WDR DA Y/NIGHT COLOUR CAMERA SCC-B2315(P)/SCC-B2015P User Manual ENG GER FRE SP A IT A SCC-B2315_Euro_D.indd 1 2007-06-07 ソタネト 1:49:24[...]

  • Seite 2

    2 3 2 3 2 This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product. T o prevent damage which may result in fire or electric shock hazard, do not exp[...]

  • Seite 3

    2 3 2 3 ENG Safety Precautions CAUTION 1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive vibration or magnetic interference. 2. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 3. Remove the power plug from the outlet w[...]

  • Seite 4

    4 5 4 5 Impor tant Safety Instr uctions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer ’ s instructions. 8. Do not install near any[...]

  • Seite 5

    4 5 4 5 ENG Contents Safety Precautions ...... 2 Important Safety Instructions ..................... 4 Contents ........................... 5 Overview ........................... 6 Special Features ........... 7 Part Names and Functions ......................... 8 Side View ......................... 8 Rear Panel ....................... 10 Installat[...]

  • Seite 6

    6 7 6 7 Ov er view This enriched WDR (Wide Dynamic Range) Day/Night camera can clearly implement both dark and bright parts on the screen with the dual shutter. Wh en a br igh t obj ec t suc h as wi ndo w oc cup ies a par t of t he sc reen , it ap pear s whi te in c onve nti onal came ras. But u sing the s tate -of- the -art WD R fun ctio n tha t t[...]

  • Seite 7

    6 7 6 7 ENG Special F eatures High Sensitivity It implements images of high sensitivity using the up-to-date Super- HAD P/S CCD. WDR The WDR function of this camera is the state-of-the-art technology that can effectively enlarge the range for screen gain. It is mainly used for taking photos for window scenes inside a building. Using this technology[...]

  • Seite 8

    8 9 8 9 Par t Names and Functions ❚ Side V iew 1 Auto Iris Lens Connector This groove is used for screwing the mount adapter, a part of the bracket where the camera will be installed. 2 Mount Adapter Fixing Grooves These grooves are used when fixing screws of the mount adap ter connec ted to the brack et when insta lling the cam era on it. 3 Back[...]

  • Seite 9

    8 9 8 9 ENG 5 ALC Lens Selection Switch This switch is used to select the type of the Auto Iris lens for use. After this setting, you have to also set the lens type in the Setup menu (In ALC… and WDR… submenus of IRIS).  DC: When the Auto Iris lens is installed for DC control signals, set the switch to “DC.”  VIDEO: When the Auto Iris[...]

  • Seite 10

    10 1 1 10 1 1 ❚ Rear Panel AC24/DC12V(SCC-B2315, B2315P) AC220V~240V(SCC-B2015P) 1 5 2 3 4 1 2 3 4 SCC-B2315_Euro_D.indd 10 2007-06-07 ソタネト 1:49:26[...]

  • Seite 11

    10 1 1 10 1 1 ENG 1 Input/Output Connector This connector has input and output jacks for RS-485 control signals, Day & Night switching, and alarm output signals. No . Function Description 1 RS-485 DA T A+ Jack for connection to RS-485 DA T A+ signal line . 2 RS-485 DA T A- Jack for connection to RS-485 DA T A- signal line. 3 ALARM OUT Alarm out[...]

  • Seite 12

    12 13 12 13 2 Setup Switch This switch is used to set the function or property . When this switch is pressed for at least 2 seconds, the Setup menu appears.  [Left/Right] movement or changing the displayed value: By pressing this switch left or right, you can move left or right on the menu or change the displayed value.  [Up/Down] movement: B[...]

  • Seite 13

    12 13 12 13 ENG Installation ❚ Before Installation Checking the contents of the package Make sure that the following items are included in the package. Things to keep in mind during installation and use  Do not disassemble the camera on your own.  Always be careful when handling the camera. Do not strike the camera by your fists or shake it[...]

  • Seite 14

    14 15 14 15 Connecting the Auto Iris Lens Connector The Auto Iris Lens Connector that is provided with your camera consists of the following parts: Connect each uncovered shutter control cables to the Auto Iris Lens Connector as the following: Pin No. DC Control T ype Video Control T ype 1 Damp(-) Power (+12V) 2 Damp(+) Not applicable 3 Drive(+) Vi[...]

  • Seite 15

    14 15 14 15 ENG ❚ Installing the Camera Mounting the lens When using the CS lens Mount th e CS lens by r otating it clockwise a s shown in the picture : When using the C lens After mounting the C-mount adapter by rotating it clockwise, turn the C lens c lockwise until it is fi xed as shown i n the pi cture. CS lens C lens SCC-B2315_Euro_D.indd 1[...]

  • Seite 16

    16 17 16 17 Setting the ALC lens selection switch Y ou can set the lens selection switch located on the side of the camera according to the lens type. When the mounted lens is an auto Iris lens of DC control type, set the switch to “DC.” When the mounted lens is an auto Iris lens of Video control type, set the switch to “VIDEO.” N Adjusting[...]

  • Seite 17

    16 17 16 17 ENG Connecting cables and checking operation 1. Connect one end of the BNC cable to the VIDEO OUT jack on the rear of the camera. 2. Connect another end of the BNC cable to the VIDEO IN jack on the monitor. N BNC cable Video Out T erminal Video In T erminal of Monitor Rear Surface SCC-B2315_Euro_D.indd 17 2007-06-07 ソタネト 1:49:30[...]

  • Seite 18

    18 19 18 19 3. Finally connect the power adapter to the camera. You can connect 2 lines of the power adapter to the camera using the Slot Head screwdriver as shown in the picture. (GND: cable with the white stripe line ) Note Connect any power source of AC 24V and DC 12V irrespective of polarity . N SCC-B2315_Euro_D.indd 18 2007-06-07 ソタネト [...]

  • Seite 19

    18 19 18 19 ENG Camera Setup T hi s ch ap te r d es cr ib es h ow t o co n fig ur e th e c am er a- re la t ed s et ti ng s . If y ou p re ss t he S e tu p sw it ch f or a t le a st 2 s ec on d s, t he S et u p me nu a pp e ar s. T he S et up O S D (O n- sc re en D is pl ay ) m ap b ri ef is l ik e th e f ol lo wi ng : CAMERA ID ON... OFF IRIS WDR[...]

  • Seite 20

    20 21 20 21 ❚ CAMERA ID This CAMERA ID menu is used to assign a camera ID to this camera. If you press the Setup switch when the CAMERA ID menu is selected, the corresponding setup screen appears. Y ou can input a camera ID composed of alphabets, numbers, and special characters up to 20 characters long. The input camera ID can be displayed at the[...]

  • Seite 21

    20 21 20 21 ENG First select any of DC LENS, VIDEO LENS, and MANU in TYPE . Y ou can adjust the shutter speed in LEVEL 1 and the brightness in LEVEL 2 . Y ou can also select any of ALL, OUTDOOR, and INDOOR in WHITE BAL . In case of ALL, this camera controls both indoor and outdoor images. ALC... If you press the Setup switch when the ALC… submenu[...]

  • Seite 22

    22 23 22 23 ELC... If you press the Setup switch when the ELC… submenu is selected, the corresponding screen appears. Y ou can make the ELC (Elec - tronic Light Control) function active or not. Like the same as the ALC configuration, you can set the BLC zone and assign the level of the high speed shutter . ❚ SHUTTER The SHUTTER menu is used to[...]

  • Seite 23

    22 23 22 23 ENG If you keep pressing the LEFT/RIGHT Setup switch, shutter speeds toggles in the following order:  OFF  AUTO X2  AUTO X4  AUTO X6  AUTO X8  AUTO X12  AUTO X16  AUTO X24  AUTO X32  AUTO X48  AUTO X64  AUTO X96  AUTO X128  AUTO X256  OFF  1/100 (NTSC), 1/120 (P AL)  1/250  1/500 [...]

  • Seite 24

    24 25 24 25 ❚ MOTION The MOTION menu is used to set the intensity of the camera AGC level for monitoring motions. This function is available only in AUTO low speed mode. Y ou can select any of S.SLOW , SLOW , NORM, F AST , and F .F AST according to the AGC intensity level. T o monitor very fast moving objects in dark illumination, select F .F AST[...]

  • Seite 25

    24 25 24 25 ENG There are 3 different types like 1, 2, and 3. Y ou cannot change the setting for type 2 because it is prefixed with the full screen. In case of 1 and 3, you can se t the motion detection area on your own. Those 3 types are like the following: 1. Window type: The selected area is displayed with a box. The motion can be detected for t[...]

  • Seite 26

    26 27 26 27 3. Block type: The screen displays with small blocks. When a motion is detected in the selected blocks, the small blocks are displayed on the screen.  PRESET : The whole screen becomes the motion detection area.  USER... : Y ou can manually set the motion detection area. Use the UP/DOWN/LEFT/RIGHT Setup switch to set the area. T o[...]

  • Seite 27

    26 27 26 27 ENG Note In case of B/W mode, it may fail to focus when B/W mode is converted to Color mode. That is because it must have the condition to have IRIS opened for the maximum before adjusting the Back-Focus. The smaller the F number of lens is, the lower the focus depth of field is (e.g. Using a high speed electronic shutter may lower the [...]

  • Seite 28

    28 29 28 29 NIGHT ... If you press the Setup switch when the NIGHT… submenu is se- lected, the corresponding screen appears. Even in night mode, you can see colour images in bright illumina- tion. Therefore you can select any of COLOUR… and BW… In case of COLOUR…, you have to set the colour temperature for white balance. Y ou can also speci[...]

  • Seite 29

    28 29 28 29 ENG For this function, you can specify the level for each conversion between Day and Night. Note When the DA Y/NIGHT is set to AUTO, the AGC is displayed with --- so you cannot change its setting. EXT This automatically converts the colour mode to BW mode and vice versa by interfacing with an external sensor . ❚ WHITE BAL The WHITE BA[...]

  • Seite 30

    30 31 30 31  A TW2 : Its colour temperature variation range is approximately from 2000°K to 10000°K.  A WC  (Auto White Balance Control): The colour temperature setting is made once. After selecting this, expose to an object to memorize the colour temperature of it and press the Setup switch. The fixed colour temperature is applied.  [...]

  • Seite 31

    30 31 30 31 ENG In case of typ e1, a box type zon e is set whi le a diamond type zone is set for the typ e 2 . When the pr ivac y is any fro m 0 to 15, four di fferen t size s of mos aics are prov ided. When the pr ivac y is any fro m 1 6 to 23, you can not change the siz e o f the mosa ic because it is alread y pr efixed. For 16 to 23 privac ies, [...]

  • Seite 32

    32 33 32 33 Note In case of LINE, it doesn’t support DC 12V , for which “---” is displayed. DIGIT AL ZOOM Y ou can set the level and ratio of digital zoom. If you press the Setup switch when ON … is selected in DIGIT AL ZOOM , the corresponding screen appears. The first displayed num ber mean s the zoom ratio and the second displaye d numb[...]

  • Seite 33

    32 33 32 33 ENG DNR Y ou can configure the DNR (Digital Noise Reduction) related set- tings. If you press the Setup switch when ON… is selected in DNR , the corresponding screen appears. Y ou can set the level for this configuration. FLICKERLESS When this is set to ON, the shutter speed is set to 1/100 sec (for NTSC) or 1/120 sec (for P AL) to [...]

  • Seite 34

    34 35 34 35 SYSTEM INFO Y ou can check the system-related information. If you press the Setup switch when … is selected in SYSTEM INFO , the corresponding screen appears. Y ou can find the system information about ROM version, EEP version, protocol, address, type, baudrate, and serial number . ❚ RS-485 Th e RS -485 me nu i s us ed to c onfig [...]

  • Seite 35

    34 35 34 35 ENG If you pre ss the Setu p s witc h wh en … is se le cted in the RS- 485 men u, th e co rres pon ding scr een app ears . Y ou can set the protocol, baudrate, and address (range: 0 to 255) for this communication ❚ EXIT The EXIT menu is used to exit from the SETUP menu. Y ou can select the following options:  QUIT : Ignores the c[...]

  • Seite 36

    36 37 36 37 Item Details Product type CCTV Camera (WDR & DA Y/NIGHT) Power source SCC-B2315: AC 24V ± 10% (60Hz ± 0.3 Hz), DC 12V +10%/-5% SCC-B2315P: AC 24V ± 10% (50Hz ± 0.3 Hz), DC 12V +10%/-5% SCC-B2015P: AC 220 to 240V ± 10% (50Hz ± 0.3 Hz) Broadcast type SC C- B231 5P , B 2015 P: P AL Stan dard C olou r Sys te m SC C- B231 5: NTS C [...]

  • Seite 37

    36 37 36 37 ENG Item Details Dynamic Range NTSC: x128 / P AL: x160 IRIS WDR/ALC/ELC Electronic shutter speed High Speed : OFF~1/10K sec Low Speed : OFF~X256 AGC OFF/LOW/HIGH Motion F .F AST/FAST/NORM/SLOW/S.SLOW Motion Detection ON/OFF Day/Night DA Y/NIGHT/AUTO/EXT White Balance A TW1/A TW2/AWC/MANUAL Mode (3200°K, 5600°K, R/B Gain adjustment) Pr[...]

  • Seite 38

    38 39 38 39 Memo SCC-B2315_Euro_D.indd 38 2007-06-07 ソタネト 1:49:35[...]

  • Seite 39

    38 39 38 39 ENG Memo SCC-B2315_Euro_D.indd 39 2007-06-07 ソタネト 1:49:35[...]

  • Seite 40

    Cor rect Disposal of T his Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. T o prevent possib[...]