Sharp PN-E802 Bedienungsanleitung

PN-E802 LCD MONIT OR OPERA TION MANUAL[...]

IMPORT ANT : T o aid reporting in case of loss or theft, please record the product’s model and serial numbers in the space provided. The numbers are located in the rear of the product. Model No.: Serial No.: U.S.A. ONL Y[...]

3 E IMPORT ANT INFORMA TION W ARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE P ARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning ash wit[...]

4 E Thank you for your purchase of a SHARP LCD product. T o ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly[...]

5 E SAFETY PRECAUTIONS (Continued) 19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below: • Use the specied batteries only . • Install the batterie[...]

6 E - The TFT color LCD panel used in this monitor is made with the application of high precision technology . However , there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness. Please note that these are not malfunctions but[...]

7 E MOUNTING PRECAUTIONS • Thisproductisforuseindoors. • A mountingbracketcompliantwithVESA specicationsis required. • Sincethemonitorisheavy ,consultyourdealerbefore installing,removingormovingthemonitor . • Mountingthemonitoronth[...]

8 E Supplied Components If any component should be missing, please contact your dealer .  Liquid Crystal Display Monitor: 1  Remote control unit: 1  Cable clamp: 2  Power cord: 1  R-6 battery (“AA” size): 2  CD-ROM (Utility Disk for Windows): 1  Setup Manual: 1  Cover: 2  Cover screws (M4 with washers): 4  V ertica[...]

9 E n Front view 1 23 45 1. LCD panel 2. Remote control sensor (See page 14. ) 3. Input switch (See page 17. ) 4. Power switch (See page 15. ) 5. Power LED (See page 15.) TIPS • Use a pointed object such as a pen tip to press the switches at the front of the monitor . Part Names n Rear view When the PN-ZB01 (optional) is attached 17 16 15 18 21 2[...]

10 E Part Names n Remote control unit 1 2 3 4 5 6 9 8 7 1. Signal transmitter 2. POWER button (See page 15.) 3. MUTE button (See page 17.) 4. VOL +/- buttons (See page 17.) BRIGHT +/- buttons (See page 17.) Cursor control ( / / / ) buttons 5. DISPLA Y button (See page 17.) 6. MODE button (See page 17.) 7. INPUT button (See page 17.) 8. MENU button [...]

11 E Connecting Peripheral Equipment Caution • Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected. • Be careful not to confuse the input terminal with the output terminal when connecting cables. Accidentally rever[...]

12 E Connecting Peripheral Equipment Connection when the PN-ZB01 (optional) is attached The PN-ZB01 expansion board (optional) allows the use of additional connection terminals. 6. PC/A V DVI-D input terminal • Set DVI of INPUT SELECT on the OPTION menu according to the device to be connected. • Select the audio input terminal to be used in PC [...]

13 E Connecting the Power Cord Caution • Use only the power cord supplied with the monitor . 1. T urn of f the main power switch. 2. Plug the power cord (supplied) into the AC input terminal. 3. Plug the power cord (supplied) into the AC power outlet. Binding Cables The cables connected to the terminals on the rear of the monitor can be fastened [...]

14 E Preparing the Remote Control Unit Installing the batteries 1. Press the cover gently and slide it in the direction of the arrow . 2. See the instructions in the compartment and put in the supplied batteries (R-6 (“AA” size) x 2) with their plus (+) and minus (-) sides oriented correctly . 3. Close the cover . TIPS • When the batteries be[...]

15 E Caution • T urn on the monitor rst before turning on the PC or playback device. T urning on the main power Main power switch Caution • The main power must be turned on/off with the main power switch. Do not connect/disconnect the power cord or turn the breaker on/off while the main power switch is on. • When switching the main power s[...]

16 E T urning Power On/Off n Date/time setting • If the time has yet to be set when the monitor is rst turned on, the date/time setting screen appears. Set the date and time. DA TE/TIME SETTING SET CANCE L // OK···[MENU] : : 01 01 12 / 12 AM 00 : / 20 1. Press , , or to select the date and time, and press or to change the numerical values. [...]

17 E Basic Operation 1 2 3 4 5 6 7 8 1. INPUT (Input mode selection) The men u is displayed. Press or to select the input mode, and press to enter . * Y ou can select the input terminal by pressing the input switch of the monitor . Input mode Video Audio PC D-SUB PC D-sub input terminal *1 Audio input terminal PC HDMI PC/A V HDMI input terminal *2 [...]

18 E Basic Operation n Switching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE PC input Displays image so it lls the entire screen. A V input An image with a 4:3 aspect ratio is stretched to ll the entire screen. ZOOM 1 PC input An image with a 4:3 aspect ratio is enl[...]

19 E Menu Items Displaying the menu screen Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 20 to 24 for details of each menu items. Caution • Do not turn the main power switch off while the menu items are being displayed. Doing so may initialize the settings. n [...]

20 E Menu item details The menu will differ depending on the input mode. n SCREEN Y ou can m ove the menu screen display position each time DISPLA Y is pressed. AUTO (PC D-SUB/PC RGB) The CLOCK , PHASE, H-POS, and V -POS are automatically adjusted. Pressing performs adjustment. Use this automatic adjustment when you use the PC D-sub input terminal [...]

21 E USER Adjusts each item when the WHITE BALANCE is set to USER. R-CONTRAST .... Adjusts bright-toned red component. G-CONTRAST .... Adjusts bright-toned green component. B-CONTRAST .... Adjusts bright-toned blue component. R-OFFSET .......... Adjusts dark-toned red component. G-OFFSET ......... Adjusts dark-toned green component. B-OFFSET ......[...]

22 E Menu Items COPY SETTING V ALUE When the monitor has been connected to multiple monitors by RS-232C, the settings in the monitor can be copied to the monitor connected to the RS-232C output terminal and to the daisy chain of connected monitors that follows. Selects the settings to copy with COPY SETTING V ALUE T ARGET . “PICTURE” ONL Y ....[...]

23 E Menu Items SCAN MODE (A V input) Sets the scan mode used for A V mode input. MODE1 ............... Over-scan display MODE2 ............... Under-scan display MODE3 ............... Under-scan display when the input signal is 1080i/p. Otherwise, over-scan display * Even when MODE1 is selected, under-scan display is used when the input signal is [...]

24 E Menu Items n PIP/PbyP PIP MODES Sets the display method. OFF ......... Displays one screen. PIP ........... Displays a sub screen inside a main screen. PbyP ........ Displays a main screen and a sub screen in a line. PbyP2 ...... Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line. PIP SIZE Set[...]

25 E n Enlarge • Y ou can align several monitors and integrate them into a single large screen to display . • Up to ve monitors can be aligned in both the horizontal and vertical directions. • Each monitor displays enlarg ed views of separated images. (Example) Horizontal direction: 2 monitors Ve rtical direction: 2 monitors Horizontal dir[...]

26 E n SCHEDULE Y ou can set the time to switch the monitor on and off. Set th is funct ion with “SCHEDU LE” in t he OPTIO N menu. (See page 22.) - : – – – – – – – – – – – – – – – – – SCHEDULE No. POWE RD AY OF THE WEEK TIM EI NPUT BRIGHT – – / – – / – – – – – – – – – : – – : – ?[...]

27 E n ADV ANCED items (A V input) (See page 20 for additional Menu item details.) FLESH TONE Adjust the hue control. 3D-NR Reduce the noise of playback images on video. Setting a higher level reduces more noise. However , it may cause blurring on an image. MPEG-NR Reduce block noise caused by digital compression. 3D-Y/C (A V VIDEO) Specify whether[...]

28 E Y ou can return the settings to their factory-preset values and restrict operations. 1. Hold SIZE down until “F” appears in the upper left corner of the screen. 2. While “F” appears, press , , , in that order . ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲▲▲▲▲▲ OFF UNLOCKED ON1 ON LED OFF MONI TO R FUNCTION 1/1 ALL RESET ADJUSTMENT[...]

29 E Controlling the Monitor with a PC (RS-232C) Y ou can control this monitor from a PC via RS-232C (COM port) on the PC. Y ou can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 30), you can make input mode selection/adjustment or can check the status of a specic monitor . Preca[...]

30 E Controlling the Monitor with a PC (RS-232C) n Response code format When a command has been executed correctly O K Return code (0D H , 0A H ) A response is returned after a command is executed. * If an ID number has been assigned O K SPC 0 0 1 ID number of respondin g monitor Space (20 H ) Return code (0D H , 0A H ) When a command has not been [...]

31 E Controlling the Monitor with a PC (RS-232C) n Commands for ID control The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST ........ . A monitor receiving this command sets its own ID number in the parameter eld. Example: IDST0001 OK 001 ← The[...]

32 E Controlling the Monitor with a PC (RS-232C) n Repeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. Y ou can use Repeater control function without assigning ID numbers. [E xamp l e ] Set 1 Set 2 Set 3S et 4 * If monitors are[...]

33 E RS-232C command table How to read the command table Command: Command eld (See page 29.) Direction: W When the “Parameter” is set in the parameter eld (see page 29), the command functions as described under “Control/Response Contents”. R The returned value indicated under “Reply” can be obtained by setting “????”, “ ?”[...]

34 E SCREEN menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) AUTO ASNC W 1 When the input mode is PC D-SUB, PC RGB. - ○ ○ CLOCK CLCK WR 0-1200 0-1200 When the input mode is PC D-SUB, PC RGB. V aries depending on the signal. PHASE PHSE WR 0-63 0-63 When the input mode is PC D-SUB, PC RGB. POSITIONING POSITI[...]

35 E PICTURE menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) AUTO AGIN W 1 When the input mode is PC D-SUB, PC RGB. - ○ ○ ANALOG GAIN ANGA WR 0-127 0-127 When the input mode is PC D-SUB, PC RGB. ○ ANALOG OFFSET ANOF WR 0-127 0-127 When the input mode is PC D-SUB, PC RGB. CONTRAST CONT WR 0-60 0-60 BLACK[...]

36 E AUDIO menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) TREBLE AUTR WR -5-5 -5-5 ○ ○ ○ BASS AUBS WR -5-5 -5-5 BALANCE AUBL WR -10-10 -10-10 RESET ARST W 3 - SETUP menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) OSD H-POSITION OSDH WR 0-100 0-100 ○ ○ ○ OSD[...]

37 E Controlling the Monitor with a PC (RS-232C) OPTION menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) DA TE/TIME SETTING DA TE WR AABBCCDDEE AABBCCDDEE AA: Y ear, BB: Month, CC: Day , DD: Hour, EE: Minute ○ ○ ○ DA TE DISPLA Y FORMA T DTFT WR 0-2 0-2 0: YYYY/MM/DD, 1: MM/DD/YYYY , 2: DD/MM/YYYY YYYY : [...]

38 E MUL TI menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) ENLARGE ENLG WR 0-1 0-1 0: OFF , 1: ON - ○ ○ ENLARGE MODE EMAG WR 0-4 0-4 0: OFF , 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5 EMHV WR 1 1-55 11-55 1 x 1 (OFF) to 5 x 5 (“m x n” is expressed as “mn”, where m and n are the numbers of monitors s[...]

39 E PIP/PbyP menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) PIP MODES MWIN WR 0-3 0-3 0: OFF , 1: PIP , 2: PbyP , 3: PbyP2 ○ ○ ○ PIP SIZE MPSZ WR 1-64 1-64 ○ PIP POS THE LONGEST DIRECTION MHPS W 0-100 ○ R 0-100 ○ THE SHORTEST DIRECTION MVPS W 0-100 ○ R 0-100 ○ PIP POS LD+SD BA TCH MPOS W 0-1[...]

40 E Others Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) SCREEN SIZE (PC) WIDE WR 1-5 1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2 ○ ○ ○ SCREEN SIZE (A V) WIDE WR 1-5 1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot ○ VOLUME VOLM WR 0-31 0-31 ○ MUTE MUTE WR 0-1 0-1 0: OFF , 1: ON[...]

41 E When the PN-ZB01 (optional) is attached, your monitor can be connected to a LAN allowing you to control it from a PC on the LAN. Y ou can also congure the monitor to send e-mail notication when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through). Hub LAN terminal LAN cabl[...]

42 E ■ T o set from a PC When the monitor is connected to a PC, LAN settings can be congured via PC. Set up process (1) Connect your monitor to a PC (2) Specify the PC’s IP address (3) Congure the monitor ’s LAN settings (1) Connecting your monitor to a PC Connect a commercially available crossover LAN cable (UPT cable, Category 5) to t[...]

43 E 6. Click on “LAN SETUP” under NETWORK. 7. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically , change this setting to “ON”. T o set the address manually , set this to “OFF”. IP ADDRESS If the DHCP CLIENT is set to “OFF”, specify an IP ad[...]

44 E ■ INFORMA TION Information about this monitor appears. ■ CONTROL Y ou can control the operations corresponding to the buttons ( POWER INPUT SIZE ) on the remote control unit. (See page 17.) TIPS • In standby mode, Power ON is the operation available. ■ ADJUSTMENT Y ou can adjust these settings which are also available on the monitor ?[...]

45 E ■ NETWORK (LAN SETUP) This screen allows you to set the settings necessary when the monitor is connected to a LAN. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically , change this setting to “ON”. T o set the address manually , set this to “OFF”. IP ADDRESS If the DHCP CLIENT is set to “OFF”[...]

46 E ■ NETWORK (GENERAL) This screen allows you to specify the general LAN settings. MONITOR NAME Specify a name for this monitor as it should appear on the Internet Explorer screen. AUTO LOGOUT TIME Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network. Specify in minutes from 1 to 65535. A valu[...]

47 E ■ MAIL (RECIPIENT) This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error . RECIPIENT E-MAIL ADDRESSES Specify the e-mail addresses to send error notication e-mail to. CONDITION Specify the conditions to send mails. When you check PERIODICAL, specify the date and time to send the [...]

48 E Controlling the Monitor with a PC (LAN) ■ SNMP Y ou can congure settings related to SNMP . SNMP SETTING Set whether to enable or disable SNMP . VERSION Set the version of the SNMP to be supported. COMMUNITY NAME 1 to 3 Set the name of the community required for the access. USER 1 to 3 Set the user name, password, authentication method and[...]

49 E T roubleshooting If you are experiencing any problem with your display , before calling for service, please review the following troubleshooting tips. There is no picture or sound. • Is the power cord disconnected? (See page 13.) • Is the main power switch off? (See page 15.) • Is the monitor in standby mode (the power LED illuminating i[...]

50 E The Power LED is ashing in red and green alternately . When “TEMPERA TURE” is displayed in the corner of the screen. • When the internal temperature of the monitor rises excessively , the brightness of the backlight decreases automatically in order to prevent high-temperature- related problems. When this occurs, “TEMPERA TURE” is [...]

51 E Specications n Product Specications Model PN-E802 LCD component 80" Class [80 inch (203.2cm) diagonal] TFT LCD Max. resolution (pixels) 1920 x 1080 Max. colors Approx. 1.06 billion colors Pixel pitch 0.923 mm (H) × 0.923 mm (V) Viewing angle 176 ° right/left/up/down (contrast ratio ≥ 10) Screen active area inch (mm) 69-3/4 x 39-[...]

52 E Specications n Dimensional Drawings Note that the values shown are approximate values. Unit: inch [mm] 3-15/16 [100] 4-13/16 [123] 3-15/16 [100] 1-15/16 [49] 2-3/4 [70] Opening width (70 [1778]) 70- 11 /16 [1795] 73-9/16 [1869] Opening height (39-1/2 [1004]) 43-1/16 [1094] 7-7/8 [200] 1-15/16 [49] 7-7/8 [200] 7-7/8 [200] VESA holes * When m[...]

53 E n Compatible signal timing (PC) VESA Wide US TEXT Sun Screen resolution Hsync Vsyn c D ot frequency Digital 640 × 480 800 × 600 848 × 480 1024 × 768 1 152 × 864 1280 × 768 1280 × 800 1280 × 960 1280 × 1024 1360 × 768 1400 × 1050 1440 × 900 1600 × 1200 *1 1680 × 1050 1920 × 1200 *1 1280 × 720 1920 × 1080 720 × 400 1024 × 768 [...]

54 E Specications n PC/A V DVI-D input terminal pins (DVI-D 24 pin) No. Function No. Function 1 TMDS data 2- 13 N.C. 2 TMDS data 2+ 14 +5V 3 TMDS data 2/4 shield 15 GND 4 N.C. 16 Hot-plug detection 5 N.C. 17 TMDS data 0- 6 DDC clock 18 TMDS data 0+ 7 DDC data 19 TMDS data 0/5 shield 8 N.C. 20 N.C. 9 TMDS data 1- 21 N.C. 10 TMDS data 1+ 22 TMDS c[...]

55 E • When installing, removing or moving the monitor , ensure that this is carried out by at least 6 people. • Be sure to use a wall-mount bracket designed or designated for mounting the monitor . • This monitor is designed to be installed on a concrete wall or pillar . Reinforced work might be necessary for some materials such as plaster /[...]

PN-E802 Mu EN12D(1)[...]